1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
|
chip soc/intel/skylake
# Enable deep Sx states
register "deep_s3_enable_ac" = "0"
register "deep_s3_enable_dc" = "0"
register "deep_s5_enable_ac" = "1"
register "deep_s5_enable_dc" = "1"
register "deep_sx_config" = "DSX_EN_WAKE_PIN"
register "eist_enable" = "1"
register "serirq_mode" = "SERIRQ_CONTINUOUS"
# Set the Thermal Control Circuit (TCC) activation value to 95C
# even though FSP integration guide says to set it to 100C for SKL-U
# (offset at 0), because when the TCC activates at 100C, the CPU
# will have already shut itself down from overheating protection.
register "tcc_offset" = "5" # TCC of 95C
# GPE configuration
# Note that GPE events called out in ASL code rely on this
# route. i.e. If this route changes then the affected GPE
# offset bits also need to be changed.
register "gpe0_dw0" = "GPP_C"
register "gpe0_dw1" = "GPP_D"
register "gpe0_dw2" = "GPP_E"
register "gen1_dec" = "0x007c0a01" # EC 0xa00-0xa7f
register "gen2_dec" = "0x000c03e1" # COM3 port 0x3e0 - 0x3ef
register "gen3_dec" = "0x00fc02e1" # COM2/4/5/6 ports 0x2e0 - 0x2ff
# Disable DPTF
register "dptf_enable" = "0"
# FSP Configuration
register "SataSalpSupport" = "0"
register "SataMode" = "0"
register "SataPortsEnable[0]" = "1"
register "SataPortsEnable[1]" = "1"
register "SataPortsEnable[2]" = "1"
register "SataPortsDevSlp[0]" = "0"
register "SataPortsDevSlp[1]" = "0"
register "SataPortsDevSlp[2]" = "0"
register "SataSpeedLimit" = "2"
register "DspEnable" = "1"
register "IoBufferOwnership" = "0"
register "SsicPortEnable" = "0"
register "ScsEmmcHs400Enabled" = "0"
register "SkipExtGfxScan" = "1"
register "HeciEnabled" = "1"
register "SaGv" = "SaGv_Enabled"
register "PmConfigSlpS3MinAssert" = "2" # 50ms
register "PmConfigSlpS4MinAssert" = "1" # 1s
register "PmConfigSlpSusMinAssert" = "3" # 500ms
register "PmConfigSlpAMinAssert" = "3" # 2s
# VR Settings Configuration for 4 Domains
#+----------------+-------+-------+-------------+-------+
#| Domain/Setting | SA | IA | GT-Unsliced | GT |
#+----------------+-------+-------+-------------+-------+
#| Psi1Threshold | 20A | 20A | 20A | 20A |
#| Psi2Threshold | 4A | 5A | 5A | 5A |
#| Psi3Threshold | 1A | 1A | 1A | 1A |
#| Psi3Enable | 1 | 1 | 1 | 1 |
#| Psi4Enable | 1 | 1 | 1 | 1 |
#| ImonSlope | 0 | 0 | 0 | 0 |
#| ImonOffset | 0 | 0 | 0 | 0 |
#| VrVoltageLimit | 1.52V | 1.52V | 1.52V | 1.52V |
#+----------------+-------+-------+-------------+-------+
register "domain_vr_config[VR_SYSTEM_AGENT]" = "{
.vr_config_enable = 1,
.psi1threshold = VR_CFG_AMP(20),
.psi2threshold = VR_CFG_AMP(4),
.psi3threshold = VR_CFG_AMP(1),
.psi3enable = 1,
.psi4enable = 1,
.imon_slope = 0x0,
.imon_offset = 0x0,
.voltage_limit = 1520,
}"
register "domain_vr_config[VR_IA_CORE]" = "{
.vr_config_enable = 1,
.psi1threshold = VR_CFG_AMP(20),
.psi2threshold = VR_CFG_AMP(5),
.psi3threshold = VR_CFG_AMP(1),
.psi3enable = 1,
.psi4enable = 1,
.imon_slope = 0x0,
.imon_offset = 0x0,
.voltage_limit = 1520,
}"
register "domain_vr_config[VR_GT_UNSLICED]" = "{
.vr_config_enable = 1,
.psi1threshold = VR_CFG_AMP(20),
.psi2threshold = VR_CFG_AMP(5),
.psi3threshold = VR_CFG_AMP(1),
.psi3enable = 1,
.psi4enable = 1,
.imon_slope = 0x0,
.imon_offset = 0x0,
.voltage_limit = 1520,
}"
register "domain_vr_config[VR_GT_SLICED]" = "{
.vr_config_enable = 1,
.psi1threshold = VR_CFG_AMP(20),
.psi2threshold = VR_CFG_AMP(5),
.psi3threshold = VR_CFG_AMP(1),
.psi3enable = 1,
.psi4enable = 1,
.imon_slope = 0x0,
.imon_offset = 0x0,
.voltage_limit = 1520,
}"
register "PcieRpEnable[2]" = "1"
register "PcieRpEnable[3]" = "1"
register "PcieRpEnable[4]" = "1"
register "PcieRpEnable[8]" = "1"
register "PcieRpEnable[9]" = "1"
register "PcieRpEnable[10]" = "1"
register "PcieRpEnable[11]" = "1"
register "PcieRpClkSrcNumber[0]" = "0"
register "PcieRpClkSrcNumber[3]" = "1"
register "PcieRpClkSrcNumber[4]" = "2"
register "PcieRpClkSrcNumber[8]" = "3"
register "PcieRpClkSrcNumber[9]" = "3"
register "PcieRpClkSrcNumber[10]" = "3"
register "PcieRpClkSrcNumber[11]" = "3"
register "usb2_ports[0]" = "USB2_PORT_MID(OC_SKIP)" # Type-A Port (right)
register "usb2_ports[1]" = "USB2_PORT_MID(OC_SKIP)" # Type-A Port (right)
register "usb2_ports[2]" = "USB2_PORT_MID(OC_SKIP)" # WiFi
register "usb2_ports[3]" = "USB2_PORT_MID(OC_SKIP)" # F_USB3 header
register "usb2_ports[4]" = "USB2_PORT_MID(OC_SKIP)" # F_USB3 header
register "usb2_ports[5]" = "USB2_PORT_MID(OC_SKIP)" # Type-A Port (left)
register "usb2_ports[6]" = "USB2_PORT_MID(OC_SKIP)" # Type-A Port (left)
register "usb2_ports[7]" = "USB2_PORT_MID(OC_SKIP)" # GL850G for F_USB1 and F_USB2 headers
register "usb3_ports[0]" = "USB3_PORT_DEFAULT(OC_SKIP)" # Type-A Port (right)
register "usb3_ports[1]" = "USB3_PORT_DEFAULT(OC_SKIP)" # Type-A Port (right)
register "usb3_ports[2]" = "USB3_PORT_DEFAULT(OC_SKIP)" # F_USB3 header
register "usb3_ports[3]" = "USB3_PORT_DEFAULT(OC_SKIP)" # F_USB3 header
# PL2 override 25W
register "power_limits_config" = "{
.tdp_pl2_override = 25,
}"
# Send an extra VR mailbox command for the PS4 exit issue
register "SendVrMbxCmd" = "2"
device cpu_cluster 0 on
device lapic 0 on end
end
device domain 0 on
device pci 00.0 on end # Host Bridge
device pci 02.0 on end # Integrated Graphics Device
device pci 04.0 on end # SA thermal subsystem
device pci 14.0 on end # USB xHCI
device pci 14.1 on end # USB xDCI (OTG)
device pci 14.2 on end # Thermal Subsystem
device pci 14.3 off end # Camera
device pci 16.0 on end # Management Engine Interface 1
device pci 16.1 off end # Management Engine Interface 2
device pci 16.2 off end # Management Engine IDE-R
device pci 16.3 off end # Management Engine KT Redirection
device pci 16.4 off end # Management Engine Interface 3
device pci 17.0 on end # SATA
device pci 1c.0 off end # PCI Express Port 1
device pci 1c.1 off end # PCI Express Port 2
device pci 1c.2 on end # PCI Express Port 3
device pci 1c.3 off end # PCI Express Port 4
device pci 1c.4 on # PCI Express Port 5
smbios_slot_desc "SlotTypePciExpressMini52pinWithoutBSKO"
"SlotLengthOther" "MPCIE_WIFI1" "SlotDataBusWidth1X"
end
device pci 1c.5 on end # PCI Express Port 6
device pci 1c.6 off end # PCI Express Port 7
device pci 1c.7 off end # PCI Express Port 8
device pci 1d.0 on # PCI Express Port 9
smbios_slot_desc "SlotTypeM2Socket3" "SlotLengthOther"
"SSD_M.2 2242/2280" "SlotDataBusWidth4X"
end
device pci 1d.1 on end # PCI Express Port 10
device pci 1d.2 on end # PCI Express Port 11
device pci 1d.3 on end # PCI Express Port 12
device pci 1e.6 off end # SDXC
device pci 1f.0 on
chip drivers/pc80/tpm
device pnp 0c31.0 on end
end
chip superio/ite/it8786e
register "TMPIN1.mode" = "THERMAL_PECI"
register "TMPIN1.offset" = "100"
register "TMPIN1.min" = "128"
register "TMPIN2.mode" = "THERMAL_RESISTOR"
register "TMPIN2.min" = "128"
register "TMPIN3.mode" = "THERMAL_MODE_DISABLED"
register "ec.vin_mask" = "VIN_ALL"
# FAN1 is CPU fan (on board)
register "FAN1.mode" = "FAN_SMART_AUTOMATIC"
register "FAN1.smart.tmpin" = " 1"
register "FAN1.smart.tmp_off" = "35"
register "FAN1.smart.tmp_start" = "60"
register "FAN1.smart.tmp_full" = "85"
register "FAN1.smart.tmp_delta" = " 2"
register "FAN1.smart.pwm_start" = "20"
register "FAN1.smart.slope" = "24"
# FAN2 is system fan (4 pin connector populated)
#register "FAN2.mode" = "FAN_MODE_OFF"
# FAN3 PWM is used for LVDS backlight control
#register "FAN3.mode" = "FAN_MODE_OFF"
device pnp 2e.1 on # COM 1
io 0x60 = 0x3f8
irq 0x70 = 4
end
device pnp 2e.2 on # COM 2
io 0x60 = 0x2f8
irq 0x70 = 3
end
device pnp 2e.3 on # Printer Port
io 0x60 = 0x378
io 0x62 = 0x778
irq 0x70 = 5
drq 0x74 = 3
end
device pnp 2e.4 on # Environment Controller
io 0x60 = 0xa40
io 0x62 = 0xa30
irq 0x70 = 9
end
device pnp 2e.5 on # Keyboard
io 0x60 = 0x60
io 0x62 = 0x64
irq 0x70 = 1
end
device pnp 2e.6 on # Mouse
irq 0x70 = 12
end
device pnp 2e.7 off # GPIO
end
device pnp 2e.8 on # COM 3
io 0x60 = 0x3e8
irq 0x70 = 3
end
device pnp 2e.9 on # COM 4
io 0x60 = 0x2e8
irq 0x70 = 4
end
device pnp 2e.a off end # CIR
device pnp 2e.b on # COM 5
io 0x60 = 0x2f0
irq 0x70 = 3
end
device pnp 2e.c on # COM 6
io 0x60 = 0x2e0
irq 0x70 = 4
end
end
end # LPC Interface
device pci 1f.1 on end # P2SB
device pci 1f.2 on end # Power Management Controller
device pci 1f.3 on end # Intel HDA
device pci 1f.4 on end # SMBus
device pci 1f.5 on end # PCH SPI
device pci 1f.6 off end # GbE
end
end
|
