1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
|
chip soc/intel/skylake
# Enable deep Sx states
register "deep_s5_enable_ac" = "1"
register "deep_s5_enable_dc" = "1"
register "deep_sx_config" = "DSX_EN_LAN_WAKE_PIN"
# GPE configuration
# Note that GPE events called out in ASL code rely on this
# route. i.e. If this route changes then the affected GPE
# offset bits also need to be changed.
register "gpe0_dw0" = "GPP_B"
register "gpe0_dw1" = "GPP_D"
register "gpe0_dw2" = "GPP_E"
# Enable DPTF
register "dptf_enable" = "1"
# FSP Configuration
register "DspEnable" = "1"
register "IoBufferOwnership" = "3"
register "ScsEmmcHs400Enabled" = "1"
register "SkipExtGfxScan" = "1"
register "SaGv" = "SaGv_Enabled"
# Enabling SLP_S3#, SLP_S4#, SLP_SUS and SLP_A Stretch
# SLP_S3 Minimum Assertion Width. Values 0: 60us, 1: 1ms, 2: 50ms, 3: 2s
register "PmConfigSlpS3MinAssert" = "0x02"
# SLP_S4 Minimum Assertion Width. Values 0: default, 1: 1s, 2: 2s, 3: 3s, 4: 4s
register "PmConfigSlpS4MinAssert" = "0x04"
# SLP_SUS Minimum Assertion Width. Values 0: 0ms, 1: 500ms, 2: 1s, 3: 4s
register "PmConfigSlpSusMinAssert" = "0x03"
# SLP_A Minimum Assertion Width. Values 0: 0ms, 1: 4s, 2: 98ms, 3: 2s
register "PmConfigSlpAMinAssert" = "0x03"
# VR Settings Configuration for 4 Domains
#+----------------+-----------+-----------+-------------+----------+
#| Domain/Setting | SA | IA | GT Unsliced | GT |
#+----------------+-----------+-----------+-------------+----------+
#| Psi1Threshold | 20A | 20A | 20A | 20A |
#| Psi2Threshold | 4A | 5A | 5A | 5A |
#| Psi3Threshold | 1A | 1A | 1A | 1A |
#| Psi3Enable | 1 | 1 | 1 | 1 |
#| Psi4Enable | 1 | 1 | 1 | 1 |
#| ImonSlope | 0 | 0 | 0 | 0 |
#| ImonOffset | 0 | 0 | 0 | 0 |
#| IccMax | 7A | 34A | 35A | 35A |
#| VrVoltageLimit | 1.52V | 1.52V | 1.52V | 1.52V |
#+----------------+-----------+-----------+-------------+----------+
register "domain_vr_config[VR_SYSTEM_AGENT]" = "{
.vr_config_enable = 1,
.psi1threshold = VR_CFG_AMP(20),
.psi2threshold = VR_CFG_AMP(4),
.psi3threshold = VR_CFG_AMP(1),
.psi3enable = 1,
.psi4enable = 1,
.imon_slope = 0x0,
.imon_offset = 0x0,
.icc_max = VR_CFG_AMP(7),
.voltage_limit = 1520,
}"
register "domain_vr_config[VR_IA_CORE]" = "{
.vr_config_enable = 1,
.psi1threshold = VR_CFG_AMP(20),
.psi2threshold = VR_CFG_AMP(5),
.psi3threshold = VR_CFG_AMP(1),
.psi3enable = 1,
.psi4enable = 1,
.imon_slope = 0x0,
.imon_offset = 0x0,
.icc_max = VR_CFG_AMP(34),
.voltage_limit = 1520,
}"
register "domain_vr_config[VR_GT_UNSLICED]" = "{
.vr_config_enable = 1,
.psi1threshold = VR_CFG_AMP(20),
.psi2threshold = VR_CFG_AMP(5),
.psi3threshold = VR_CFG_AMP(1),
.psi3enable = 1,
.psi4enable = 1,
.imon_slope = 0x0,
.imon_offset = 0x0,
.icc_max = VR_CFG_AMP(35),
.voltage_limit = 1520,
}"
register "domain_vr_config[VR_GT_SLICED]" = "{
.vr_config_enable = 1,
.psi1threshold = VR_CFG_AMP(20),
.psi2threshold = VR_CFG_AMP(5),
.psi3threshold = VR_CFG_AMP(1),
.psi3enable = 1,
.psi4enable = 1,
.imon_slope = 0x0,
.imon_offset = 0x0,
.icc_max = VR_CFG_AMP(35),
.voltage_limit = 1520,
}"
# Enable Root port 1 and 5.
register "PcieRpEnable[0]" = "1"
register "PcieRpEnable[4]" = "1"
# Enable CLKREQ#
register "PcieRpClkReqSupport[0]" = "1"
register "PcieRpClkReqSupport[4]" = "1"
# RP 1 uses SRCCLKREQ1# while RP 5 uses SRCCLKREQ2#
register "PcieRpClkReqNumber[0]" = "1"
register "PcieRpClkReqNumber[4]" = "2"
register "i2c_voltage[4]" = "I2C_VOLTAGE_1V8" # I2C4 is 1.8V
# Must leave UART0 enabled or SD/eMMC will not work as PCI
register "SerialIoDevMode" = "{
[PchSerialIoIndexI2C0] = PchSerialIoPci,
[PchSerialIoIndexI2C1] = PchSerialIoPci,
[PchSerialIoIndexI2C2] = PchSerialIoDisabled,
[PchSerialIoIndexI2C3] = PchSerialIoDisabled,
[PchSerialIoIndexI2C4] = PchSerialIoPci,
[PchSerialIoIndexI2C5] = PchSerialIoDisabled,
[PchSerialIoIndexSpi0] = PchSerialIoDisabled,
[PchSerialIoIndexSpi1] = PchSerialIoDisabled,
[PchSerialIoIndexUart0] = PchSerialIoPci,
[PchSerialIoIndexUart1] = PchSerialIoDisabled,
[PchSerialIoIndexUart2] = PchSerialIoSkipInit,
}"
# PL2 override 25W
register "power_limits_config" = "{
.tdp_pl2_override = 25,
}"
# Send an extra VR mailbox command for the PS4 exit issue
register "SendVrMbxCmd" = "2"
# Use default SD card detect GPIO configuration
register "sdcard_cd_gpio" = "GPP_A7"
device domain 0 on
device ref igpu on end
device ref sa_thermal on end
device ref south_xhci on
register "usb2_ports" = "{
[0] = USB2_PORT_TYPE_C(OC0), /* Type-C Port 1 */
[1] = USB2_PORT_TYPE_C(OC1), /* Type-C Port 2 */
[2] = USB2_PORT_MID(OC_SKIP), /* Bluetooth */
[4] = USB2_PORT_MID(OC2), /* Type-A Port (card) */
[6] = USB2_PORT_FLEX(OC_SKIP), /* Camera */
[8] = USB2_PORT_LONG(OC3), /* Type-A Port (board) */
}"
register "usb3_ports" = "{
[0] = USB3_PORT_DEFAULT(OC0), /* Type-C Port 1 */
[1] = USB3_PORT_DEFAULT(OC1), /* Type-C Port 2 */
[2] = USB3_PORT_DEFAULT(OC2), /* Type-A Port (card) */
[3] = USB3_PORT_DEFAULT(OC3), /* Type-A Port (board) */
}"
end
device ref thermal on end
device ref i2c0 on
chip drivers/i2c/generic
register "hid" = ""ELAN0001""
register "desc" = ""ELAN Touchscreen""
register "irq" = "ACPI_IRQ_EDGE_LOW(GPP_E7_IRQ)"
device i2c 10 on end
end
end
device ref i2c1 on
chip drivers/i2c/generic
register "hid" = ""ELAN0000""
register "desc" = ""ELAN Touchpad""
register "irq" = "ACPI_IRQ_EDGE_LOW(GPP_B3_IRQ)"
register "wake" = "GPE0_DW0_05"
device i2c 15 on end
end
end
device ref heci1 on end
device ref uart2 on end
device ref i2c4 on
chip drivers/i2c/nau8825
register "irq" = "ACPI_IRQ_LEVEL_LOW(GPP_F10_IRQ)"
register "jkdet_enable" = "1"
register "jkdet_pull_enable" = "1"
register "jkdet_pull_up" = "1"
register "jkdet_polarity" = "1" # ActiveLow
register "vref_impedance" = "2" # 125kOhm
register "micbias_voltage" = "6" # 2.754
register "sar_threshold_num" = "4"
register "sar_threshold[0]" = "0x08"
register "sar_threshold[1]" = "0x12"
register "sar_threshold[2]" = "0x26"
register "sar_threshold[3]" = "0x73"
register "sar_hysteresis" = "0"
register "sar_voltage" = "6"
register "sar_compare_time" = "1" # 1us
register "sar_sampling_time" = "1" # 4us
register "short_key_debounce" = "3" # 30ms
register "jack_insert_debounce" = "7" # 512ms
register "jack_eject_debounce" = "0"
device i2c 1a on end
end
chip drivers/i2c/generic
register "hid" = ""INT343B""
register "desc" = ""SSM4567 Left Speaker Amp""
register "uid" = "0"
register "device_present_gpio" = "GPP_E3"
device i2c 34 on end
end
chip drivers/i2c/generic
register "hid" = ""INT343B""
register "desc" = ""SSM4567 Right Speaker Amp""
register "uid" = "1"
register "device_present_gpio" = "GPP_E3"
device i2c 35 on end
end
end
device ref pcie_rp1 on
chip drivers/wifi/generic
register "wake" = "GPE0_DW0_16"
device pci 00.0 on end
end
end
device ref pcie_rp5 on end
device ref uart0 on end
device ref emmc on end
device ref sdxc on end
device ref lpc_espi on
# EC host command ranges are in 0x800-0x8ff & 0x200-0x20f
register "gen1_dec" = "0x00fc0801"
register "gen2_dec" = "0x000c0201"
chip drivers/pc80/tpm
device pnp 0c31.0 on end
end
chip ec/google/chromeec
device pnp 0c09.0 on end
end
end
device ref hda on
chip drivers/generic/max98357a
register "hid" = ""MX98357A""
register "sdmode_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_E3)"
register "device_present_gpio" = "GPP_E3"
register "device_present_gpio_invert" = "1"
device generic 0 on end
end
end
device ref smbus on end
device ref fast_spi on end
end
end
|
