1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
|
chip soc/intel/tigerlake
register "power_limits_config[POWER_LIMITS_U_2_CORE]" = "{
.tdp_pl1_override = 15,
.tdp_pl2_override = 51,
}"
register "power_limits_config[POWER_LIMITS_U_4_CORE]" = "{
.tdp_pl1_override = 15,
.tdp_pl2_override = 51,
}"
register "tcc_offset" = "5" # TCC of 95
register "TcssAuxOri" = "1"
register "DdiPort1Hpd" = "0"
register "DdiPort2Hpd" = "0"
register "IomTypeCPortPadCfg[0]" = "0x090E000A"
register "IomTypeCPortPadCfg[1]" = "0x090E000D"
#+-------------------+---------------------------+
#| Field | Value |
#+-------------------+---------------------------+
#| chipset_lockdown | CHIPSET_LOCKDOWN_COREBOOT |
#| GSPI0 | cr50 TPM. Early init is |
#| | required to set up a BAR |
#| | for TPM communication |
#| | before memory is up |
#| GSPI1 | Fingerprint MCU |
#| I2C0 | Audio |
#| I2C1 | Touchscreen |
#| I2C2 | WLAN, SAR0 |
#| I2C3 | Camera, SAR1 |
#| I2C5 | Trackpad |
#+-------------------+---------------------------+
register "common_soc_config" = "{
.chipset_lockdown = CHIPSET_LOCKDOWN_COREBOOT,
.gspi[0] = {
.speed_mhz = 1,
.early_init = 1,
},
.i2c[0] = {
.speed = I2C_SPEED_FAST,
},
.i2c[1] = {
.speed = I2C_SPEED_FAST,
},
.i2c[2] = {
.speed = I2C_SPEED_FAST,
},
.i2c[3] = {
.speed = I2C_SPEED_FAST,
},
.i2c[5] = {
.speed = I2C_SPEED_FAST,
.speed_config[0] = {
.speed = I2C_SPEED_FAST,
.scl_lcnt = 163,
.scl_hcnt = 75,
.sda_hold = 36,
},
},
}"
#These settings improve the USB2 Port1 eye diagram
register "usb2_ports[4]" = "{
.enable = 1,
.tx_bias = 7,
.tx_emp_enable = 7,
.pre_emp_bias = 3,
.pre_emp_bit = 0,
}"
device domain 0 on
device ref dptf on
# DPTF Policy for Eldrid board
chip drivers/intel/dptf
## Disable Active Policy from baseboard
register "policies.active" = "{[0] = {.target=DPTF_NONE}}"
## Passive Policy
register "policies.passive[0]" = "DPTF_PASSIVE(CPU,CPU,95,5000)"
register "policies.passive[1]" = "DPTF_PASSIVE(CPU,TEMP_SENSOR_2,60,6000)"
## Critical Policy
register "policies.critical[0]" = "DPTF_CRITICAL(CPU,100,SHUTDOWN)"
register "policies.critical[1]" = "DPTF_CRITICAL(TEMP_SENSOR_2,80,SHUTDOWN)"
## Power Limits Control
# 3-15W PL1 in 200mW increments, avg over 28-32s interval
# PL2 is fixed at 51W, avg over 28-32s interval
register "controls.power_limits" = "{
.pl1 = {.min_power = 3000,
.max_power = 15000,
.time_window_min = 28 * MSECS_PER_SEC,
.time_window_max = 32 * MSECS_PER_SEC,
.granularity = 200,},
.pl2 = {.min_power = 15000,
.max_power = 51000,
.time_window_min = 28 * MSECS_PER_SEC,
.time_window_max = 32 * MSECS_PER_SEC,
.granularity = 1000,}}"
device generic 0 on end
end
end
device ref i2c0 on
chip drivers/i2c/generic
register "hid" = ""10EC5682""
register "name" = ""RT58""
register "desc" = ""Headset Codec""
register "irq_gpio" = "ACPI_GPIO_IRQ_EDGE_BOTH(GPP_F8)"
# Set the jd_src to RT5668_JD1 for jack detection
register "property_count" = "1"
register "property_list[0].type" = "ACPI_DP_TYPE_INTEGER"
register "property_list[0].name" = ""realtek,jd-src""
register "property_list[0].integer" = "1"
device i2c 1a on end
end
end
device ref i2c1 on
chip drivers/i2c/hid
register "generic.hid" = ""GDIX0000""
register "generic.desc" = ""Goodix Touchscreen""
register "generic.irq" = "ACPI_IRQ_LEVEL_LOW(GPP_E7_IRQ)"
register "generic.probed" = "1"
register "generic.reset_gpio" =
"ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C10)"
register "generic.reset_delay_ms" = "30"
register "generic.reset_off_delay_ms" = "3"
register "generic.enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_A8)"
register "generic.enable_delay_ms" = "12"
register "generic.stop_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_E3)"
register "generic.stop_off_delay_ms" = "1"
register "generic.has_power_resource" = "1"
register "hid_desc_reg_offset" = "0x01"
device i2c 14 on end
end
chip drivers/i2c/hid
register "generic.hid" = ""ELAN90FC""
register "generic.desc" = ""ELAN Touchscreen""
register "generic.irq" = "ACPI_IRQ_LEVEL_LOW(GPP_E7_IRQ)"
register "generic.probed" = "1"
register "generic.reset_gpio" =
"ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C10)"
register "generic.enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_A8)"
register "generic.reset_delay_ms" = "20"
register "generic.has_power_resource" = "1"
register "generic.disable_gpio_export_in_crs" = "1"
register "hid_desc_reg_offset" = "0x01"
device i2c 10 on end
end
end
device ref i2c5 on
chip drivers/i2c/generic
register "hid" = ""ELAN0000""
register "desc" = ""ELAN Touchpad""
register "irq" = "ACPI_IRQ_WAKE_LEVEL_LOW(GPP_E15_IRQ)"
register "wake" = "GPE0_DW2_15"
register "probed" = "1"
device i2c 15 on end
end
end
device ref hda on
chip drivers/generic/max98357a
register "hid" = ""MX98357A""
register "sdmode_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_A10)"
register "sdmode_delay" = "5"
device generic 0 on end
end
end
device ref pmc hidden
# The pmc_mux chip driver is a placeholder for the
# PMC.MUX device in the ACPI hierarchy.
chip drivers/intel/pmc_mux
device generic 0 on
chip drivers/intel/pmc_mux/conn
register "usb2_port_number" = "9"
register "usb3_port_number" = "1"
# SBU & HSL follow CC
device generic 0 on end
end
chip drivers/intel/pmc_mux/conn
register "usb2_port_number" = "4"
register "usb3_port_number" = "2"
# SBU is fixed, HSL follows CC
register "sbu_orientation" = "TYPEC_ORIENTATION_NORMAL"
device generic 1 on end
end
end
end
end # PMC
device ref north_xhci on
chip drivers/usb/acpi
device ref tcss_root_hub on
chip drivers/usb/acpi
register "desc" = ""USB3 Type-C Port C0 (MLB)""
register "type" = "UPC_TYPE_C_USB2_SS_SWITCH"
register "group" = "ACPI_PLD_GROUP(3, 2)"
device ref tcss_usb3_port1 on end
end
chip drivers/usb/acpi
register "desc" = ""USB3 Type-C Port C1 (DB)""
register "type" = "UPC_TYPE_C_USB2_SS_SWITCH"
register "group" = "ACPI_PLD_GROUP(2, 2)"
device ref tcss_usb3_port2 on
probe DB_USB USB3_ACTIVE
end
end
end
end
end
device ref south_xhci on
chip drivers/usb/acpi
device ref xhci_root_hub on
chip drivers/usb/acpi
register "desc" = ""USB2 Type-A Port A0 (MLB)""
register "type" = "UPC_TYPE_A"
register "group" = "ACPI_PLD_GROUP(1, 1)"
device ref usb2_port1 on end
end
chip drivers/usb/acpi
register "desc" = ""USB2 Type-C Port C1 (DB)""
register "type" = "UPC_TYPE_C_USB2_SS_SWITCH"
register "group" = "ACPI_PLD_GROUP(2, 1)"
device ref usb2_port4 on
probe DB_USB USB3_ACTIVE
end
end
chip drivers/usb/acpi
register "desc" = ""USB2 Camera""
register "type" = "UPC_TYPE_INTERNAL"
# The Linux Kernel does not allow an inverted BOTH_EDGE irq
# So we need to use GpioIO() instead of GpioInt()
# https://www.kernel.org/doc/Documentation/acpi/gpio-properties.txt
register "privacy_gpio" = "ACPI_GPIO_INPUT_ACTIVE_LOW(GPP_D4)"
device ref usb2_port5 on end
end
chip drivers/usb/acpi
register "desc" = ""USB2 Type-C Port C0 (MLB)""
register "type" = "UPC_TYPE_C_USB2_SS_SWITCH"
register "group" = "ACPI_PLD_GROUP(3, 1)"
device ref usb2_port9 on end
end
chip drivers/usb/acpi
register "desc" = ""USB2 Bluetooth""
register "type" = "UPC_TYPE_INTERNAL"
register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_A13)"
device ref usb2_port10 on end
end
chip drivers/usb/acpi
register "desc" = ""USB3 Type-A Port A0 (MLB)""
register "type" = "UPC_TYPE_USB3_A"
register "group" = "ACPI_PLD_GROUP(1, 2)"
device ref usb3_port1 on end
end
end
end
end
end
end
|
