1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
|
/* SPDX-License-Identifier: GPL-2.0-only */
#include <bootmode.h>
#include <console/console.h>
#include <delay.h>
#include <device/device.h>
#include <device/i2c_simple.h>
#include <drivers/ti/sn65dsi86bridge/sn65dsi86bridge.h>
#include <framebuffer_info.h>
#include <soc/display/mipi_dsi.h>
#include <soc/display/mdssreg.h>
#include <soc/qupv3_config.h>
#include <soc/qupv3_i2c.h>
#include <soc/usb.h>
#include "board.h"
#define BRIDGE_BUS 0x2
#define BRIDGE_CHIP 0x2d
static struct usb_board_data usb0_board_data = {
.pll_bias_control_2 = 0x22,
.imp_ctrl1 = 0x08,
.port_tune1 = 0xc5,
};
static void setup_usb(void)
{
/* Assert EN_PP3300_HUB for those board variants that use it. */
gpio_output(GPIO(84), 1);
setup_usb_host0(&usb0_board_data);
}
static void qi2s_configure_gpios(void)
{
gpio_configure(GPIO(49), GPIO49_FUNC_MI2S_1_SCK,
GPIO_NO_PULL, GPIO_8MA, GPIO_OUTPUT);
gpio_configure(GPIO(50), GPIO50_FUNC_MI2S_1_WS,
GPIO_NO_PULL, GPIO_8MA, GPIO_OUTPUT);
gpio_configure(GPIO(51), GPIO51_FUNC_MI2S_1_DATA0,
GPIO_NO_PULL, GPIO_8MA, GPIO_OUTPUT);
}
static void load_qup_fw(void)
{
qupv3_se_fw_load_and_init(QUPV3_0_SE1, SE_PROTOCOL_SPI, MIXED); /* ESIM SPI */
qupv3_se_fw_load_and_init(QUPV3_0_SE3, SE_PROTOCOL_UART, FIFO); /* BT UART */
qupv3_se_fw_load_and_init(QUPV3_0_SE4, SE_PROTOCOL_I2C, MIXED); /* Pen Detect I2C */
qupv3_se_fw_load_and_init(QUPV3_0_SE5, SE_PROTOCOL_I2C, MIXED); /* SAR I2C */
qupv3_se_fw_load_and_init(QUPV3_1_SE1, SE_PROTOCOL_I2C, MIXED); /* Trackpad I2C */
/*
* When coreboot firmware disables serial output,
* we still need to load console UART QUP FW for OS.
*/
if (!CONFIG(CONSOLE_SERIAL))
qupv3_se_fw_load_and_init(QUPV3_1_SE2, SE_PROTOCOL_UART, FIFO);
qupv3_se_fw_load_and_init(QUPV3_1_SE3, SE_PROTOCOL_I2C, MIXED); /* Speaker Amps I2C */
qupv3_se_fw_load_and_init(QUPV3_1_SE4, SE_PROTOCOL_SPI, MIXED); /* Fingerprint SPI */
qupv3_se_fw_load_and_init(QUPV3_1_SE5, SE_PROTOCOL_I2C, MIXED); /* Codec I2C */
}
static void configure_display(void)
{
printk(BIOS_INFO, "%s: Bridge gpio init\n", __func__);
/* Bridge Enable GPIO */
gpio_output(GPIO_EDP_BRIDGE_ENABLE, 1);
/* PP3300 EDP power supply */
gpio_output(GPIO_EN_PP3300_DX_EDP, 1);
}
static void display_init(struct edid *edid)
{
uint32_t dsi_bpp = 24;
uint32_t lanes = 4;
if (mdss_dsi_config(edid, lanes, dsi_bpp))
return;
sn65dsi86_bridge_configure(BRIDGE_BUS, BRIDGE_CHIP, edid, lanes, dsi_bpp);
mdp_dsi_video_config(edid);
mdss_dsi_video_mode_config(edid, dsi_bpp);
mdp_dsi_video_on();
}
static void display_startup(void)
{
static struct edid ed;
enum dp_pll_clk_src ref_clk = SN65_SEL_19MHZ;
i2c_init(QUPV3_0_SE2, I2C_SPEED_FAST); /* EDP Bridge I2C */
if (display_init_required()) {
configure_display();
mdelay(250); /* Delay for the panel to be up */
sn65dsi86_bridge_init(BRIDGE_BUS, BRIDGE_CHIP, ref_clk);
if (sn65dsi86_bridge_read_edid(BRIDGE_BUS, BRIDGE_CHIP, &ed) < 0)
return;
printk(BIOS_INFO, "display init!\n");
/* Configure backlight */
gpio_output(GPIO_BACKLIGHT_ENABLE, 1);
display_init(&ed);
fb_new_framebuffer_info_from_edid(&ed, (uintptr_t)0);
} else
printk(BIOS_INFO, "Skipping display init.\n");
}
static void mainboard_init(struct device *dev)
{
setup_usb();
qi2s_configure_gpios();
load_qup_fw();
display_startup();
}
static void mainboard_enable(struct device *dev)
{
dev->ops->init = &mainboard_init;
}
struct chip_operations mainboard_ops = {
.name = CONFIG_MAINBOARD_PART_NUMBER,
.enable_dev = mainboard_enable,
};
|
