1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
|
/* SPDX-License-Identifier: GPL-2.0-only */
#include <bootmode.h>
#include <cbfs.h>
#include <console/console.h>
#include <delay.h>
#include <device/device.h>
#include <device/i2c_simple.h>
#include <device/mmio.h>
#include <mipi/panel.h>
#include <drivers/ti/sn65dsi86bridge/sn65dsi86bridge.h>
#include <edid.h>
#include <framebuffer_info.h>
#include <soc/display/mipi_dsi.h>
#include <soc/display/mdssreg.h>
#include <soc/qupv3_config_common.h>
#include <soc/qup_se_handlers_common.h>
#include <soc/qupv3_i2c_common.h>
#include <soc/qcom_qup_se.h>
#include <soc/usb.h>
#include <types.h>
#include "board.h"
#include <soc/addressmap.h>
#define BRIDGE_BUS QUPV3_0_SE2
#define BRIDGE_CHIP 0x2d
static struct usb_board_data usb0_board_data = {
.pll_bias_control_2 = 0x22,
.imp_ctrl1 = 0x08,
.port_tune1 = 0xc5,
};
static void setup_usb(void)
{
/* Assert EN_PP3300_HUB for those board variants that use it. */
gpio_output(GPIO(84), 1);
setup_usb_host0(&usb0_board_data);
}
static void qi2s_configure_gpios(void)
{
gpio_configure(GPIO(49), GPIO49_FUNC_MI2S_1_SCK,
GPIO_NO_PULL, GPIO_8MA, GPIO_OUTPUT);
gpio_configure(GPIO(50), GPIO50_FUNC_MI2S_1_WS,
GPIO_NO_PULL, GPIO_8MA, GPIO_OUTPUT);
gpio_configure(GPIO(51), GPIO51_FUNC_MI2S_1_DATA0,
GPIO_NO_PULL, GPIO_8MA, GPIO_OUTPUT);
}
static void load_qup_fw(void)
{
qupv3_se_fw_load_and_init(QUPV3_0_SE1, SE_PROTOCOL_SPI, MIXED); /* ESIM SPI */
qupv3_se_fw_load_and_init(QUPV3_0_SE3, SE_PROTOCOL_UART, FIFO); /* BT UART */
qupv3_se_fw_load_and_init(QUPV3_0_SE4, SE_PROTOCOL_I2C, MIXED); /* Pen Detect I2C */
qupv3_se_fw_load_and_init(QUPV3_0_SE5, SE_PROTOCOL_I2C, MIXED); /* SAR I2C */
qupv3_se_fw_load_and_init(QUPV3_1_SE1, SE_PROTOCOL_I2C, MIXED); /* Trackpad I2C */
/*
* When coreboot firmware disables serial output,
* we still need to load console UART QUP FW for OS.
*/
if (!CONFIG(CONSOLE_SERIAL))
qupv3_se_fw_load_and_init(QUPV3_1_SE2, SE_PROTOCOL_UART, FIFO);
qupv3_se_fw_load_and_init(QUPV3_1_SE3, SE_PROTOCOL_I2C, MIXED); /* Speaker Amps I2C */
qupv3_se_fw_load_and_init(QUPV3_1_SE4, SE_PROTOCOL_SPI, MIXED); /* Fingerprint SPI */
qupv3_se_fw_load_and_init(QUPV3_1_SE5, SE_PROTOCOL_I2C, MIXED); /* Codec I2C */
}
static void power_on_bridge(void)
{
printk(BIOS_INFO, "%s: Bridge gpio init\n", __func__);
/* Bridge Enable GPIO */
gpio_output(GPIO_EDP_BRIDGE_ENABLE, 1);
/* PP3300 EDP power supply */
gpio_output(GPIO_EN_PP3300_DX_EDP, 1);
}
static void configure_mipi_panel(void)
{
int panel_id = sku_id() >> 8;
gpio_output(GPIO_MIPI_1V8_ENABLE, 1);
mdelay(5);
gpio_output(GPIO_AVDD_LCD_ENABLE, 1);
mdelay(5);
gpio_output(GPIO_AVEE_LCD_ENABLE, 1);
mdelay(15);
gpio_output(GPIO_VDD_RESET_1V8, 1);
mdelay(15);
/*
* In mrbland, BOE panel_id = 3, it needs 15ms delay and
* do reset again according to spec(See in b/197300876).
*/
if (CONFIG(BOARD_GOOGLE_MRBLAND) && (panel_id == 3)) {
gpio_output(GPIO_VDD_RESET_1V8, 0);
mdelay(5);
gpio_output(GPIO_VDD_RESET_1V8, 1);
}
}
static struct panel_serializable_data *get_mipi_panel(enum lb_fb_orientation *orientation)
{
const char *cbfs_filename = NULL;
int panel_id = sku_id() >> 8;
if (CONFIG(BOARD_GOOGLE_MRBLAND)) {
switch (panel_id) {
case 3:
cbfs_filename = "panel-BOE_TV101WUM_N53";
*orientation = LB_FB_ORIENTATION_LEFT_UP;
break;
case 6:
cbfs_filename = "panel-AUO_B101UAN08_3";
*orientation = LB_FB_ORIENTATION_LEFT_UP;
break;
}
}
if (CONFIG(BOARD_GOOGLE_WORMDINGLER)) {
switch (panel_id) {
case 0:
cbfs_filename = "panel-INX_P110ZZD_DF0";
*orientation = LB_FB_ORIENTATION_LEFT_UP;
break;
case 4:
cbfs_filename = "panel-BOE_TV110C9M_LL0";
*orientation = LB_FB_ORIENTATION_LEFT_UP;
break;
}
}
if (!cbfs_filename)
return NULL;
struct panel_serializable_data *panel = cbfs_map(cbfs_filename, NULL);
if (!panel) {
printk(BIOS_ERR, "Could not find panel data for %s!\n", cbfs_filename);
return NULL;
}
return panel;
}
static enum cb_err display_init(struct panel_serializable_data *panel)
{
uint32_t dsi_bpp = 24;
uint32_t lanes = 4;
if (mdss_dsi_config(&panel->edid, lanes, dsi_bpp))
return CB_ERR;
if (CONFIG(TROGDOR_HAS_MIPI_PANEL)) {
if (mdss_dsi_panel_initialize(panel->init))
return CB_ERR;
} else {
sn65dsi86_bridge_configure(BRIDGE_BUS, BRIDGE_CHIP, &panel->edid,
lanes, dsi_bpp);
if (CONFIG(TROGDOR_HAS_BRIDGE_BACKLIGHT))
sn65dsi86_backlight_enable(BRIDGE_BUS, BRIDGE_CHIP);
}
mdp_dsi_video_config(&panel->edid);
mdss_dsi_video_mode_config(&panel->edid, dsi_bpp);
mdp_dsi_video_on();
return CB_SUCCESS;
}
static void display_startup(void)
{
struct panel_serializable_data edp_panel = {0};
struct panel_serializable_data *panel = &edp_panel;
enum lb_fb_orientation orientation = LB_FB_ORIENTATION_NORMAL;
/* Always initialize this so QUP firmware is loaded for the kernel. */
i2c_init(BRIDGE_BUS, I2C_SPEED_FAST);
if (!display_init_required()) {
printk(BIOS_INFO, "Skipping display init.\n");
return;
}
if (CONFIG(TROGDOR_HAS_MIPI_PANEL)) {
configure_mipi_panel();
panel = get_mipi_panel(&orientation);
if (!panel)
return;
} else {
enum dp_pll_clk_src ref_clk = SN65_SEL_19MHZ;
power_on_bridge();
mdelay(250); /* Delay for the panel to be up */
sn65dsi86_bridge_init(BRIDGE_BUS, BRIDGE_CHIP, ref_clk);
if (sn65dsi86_bridge_read_edid(BRIDGE_BUS, BRIDGE_CHIP, &panel->edid) < 0)
return;
}
printk(BIOS_INFO, "display init!\n");
edid_set_framebuffer_bits_per_pixel(&panel->edid, 32, 0);
if (display_init(panel) == CB_SUCCESS) {
struct fb_info *fb = fb_new_framebuffer_info_from_edid(&panel->edid, 0);
fb_set_orientation(fb, orientation);
}
}
static void configure_sdhci(void)
{
/* Program eMMC drive strength to 16/16/16 mA */
write32((void *)SDC1_TLMM_CFG_ADDR, 0x9FFF);
/* Program SD card drive strength to 16/10/10 mA */
write32((void *)SDC2_TLMM_CFG_ADDR, 0x1FE4);
}
static void mainboard_init(struct device *dev)
{
/* Take FPMCU out of reset. Power was already applied
in romstage and should have stabilized by now. */
if (CONFIG(TROGDOR_HAS_FINGERPRINT))
gpio_output(GPIO_FP_RST_L, 1);
setup_usb();
qi2s_configure_gpios();
load_qup_fw();
display_startup();
configure_sdhci();
}
static void mainboard_enable(struct device *dev)
{
dev->ops->init = &mainboard_init;
}
struct chip_operations mainboard_ops = {
.enable_dev = mainboard_enable,
};
|
