1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
|
/*
* This file is part of the coreboot project.
*
* Copyright (c) 2015, The Linux Foundation. All rights reserved.
* Copyright 2014 Google Inc.
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; version 2 of the License.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
*/
#include <boardid.h>
#include <boot/coreboot_tables.h>
#include <delay.h>
#include <device/device.h>
#include <gpio.h>
#include <soc/clock.h>
#include <soc/soc_services.h>
#include <soc/usb.h>
#include <symbols.h>
#include <vendorcode/google/chromeos/chromeos.h>
#include "mmu.h"
#define USB_ENABLE_GPIO 51
static void setup_usb(void)
{
#if !CONFIG_BOARD_VARIANT_AP148
gpio_tlmm_config_set(USB_ENABLE_GPIO, FUNC_SEL_GPIO,
GPIO_PULL_UP, GPIO_10MA, GPIO_ENABLE);
gpio_set(USB_ENABLE_GPIO, 1);
#endif
usb_clock_config();
setup_usb_host1();
}
#define TPM_RESET_GPIO 22
static void setup_tpm(void)
{
if (board_id() != BOARD_ID_PROTO_0)
return; /* Only proto0 have TPM reset connected to GPIO22 */
gpio_tlmm_config_set(TPM_RESET_GPIO, FUNC_SEL_GPIO, GPIO_PULL_UP,
GPIO_4MA, GPIO_ENABLE);
/*
* Generate a reset pulse. The spec calls for 80 us minimum, let's
* make it twice as long. If the output was driven low originally, the
* reset pulse will be even longer.
*/
gpio_set(TPM_RESET_GPIO, 0);
udelay(160);
gpio_set(TPM_RESET_GPIO, 1);
}
#define SW_RESET_GPIO 26
static void assert_sw_reset(void)
{
if (board_id() == BOARD_ID_PROTO_0)
return;
/*
* only proto0.2 and later care about this. We want to keep the
* ethernet switch in reset, otherwise it comes up in default
* (bridging) mode.
*/
gpio_tlmm_config_set(SW_RESET_GPIO, FUNC_SEL_GPIO,
GPIO_PULL_UP, GPIO_4MA, GPIO_ENABLE);
gpio_set(SW_RESET_GPIO, 1);
}
static void mainboard_init(device_t dev)
{
/* disable mmu and d-cache before setting up secure world.*/
dcache_mmu_disable();
start_tzbsp();
/* Setup mmu and d-cache again as non secure entries. */
setup_mmu(DRAM_INITIALIZED);
start_rpm();
setup_usb();
assert_sw_reset();
setup_tpm();
/* Functionally a 0-cost no-op if NAND is not present */
board_nand_init();
#if IS_ENABLED(CONFIG_CHROMEOS)
/* Copy WIFI calibration data into CBMEM. */
cbmem_add_vpd_calibration_data();
#endif
/*
* Make sure bootloader can issue sounds The frequency is calculated
* as "<frame_rate> * <bit_width> * <channels> * 4", i.e.
*
* 48000 * 2 * 16 * 4 = 6144000
*/
audio_clock_config(6144000);
}
static void mainboard_enable(device_t dev)
{
dev->ops->init = &mainboard_init;
}
struct chip_operations mainboard_ops = {
.name = "storm",
.enable_dev = mainboard_enable,
};
void lb_board(struct lb_header *header)
{
struct lb_range *dma;
dma = (struct lb_range *)lb_new_record(header);
dma->tag = LB_TAB_DMA;
dma->size = sizeof(*dma);
dma->range_start = (uintptr_t)_dma_coherent;
dma->range_size = _dma_coherent_size;
#if IS_ENABLED(CONFIG_CHROMEOS)
/* Retrieve the switch interface MAC addressses. */
lb_table_add_macs_from_vpd(header);
#endif
}
|
