blob: 3de0ec84d5933361f8506df919d44b579de961c9 (
plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
|
# SPDX-License-Identifier: GPL-2.0-or-later
chip soc/amd/mendocino
# Set Package Power Parameters
register "thermctl_limit_degreeC" = "92"
# STT settings
register "stt_control" = "1"
register "stt_pcb_sensor_count" = "2"
register "stt_error_coeff" = "0x0038"
register "stt_error_rate_coefficient" = "0x0ed9"
register "stt_min_limit" = "15000"
register "stt_skin_temp_apu" = "0x2700"
# STT default mode
register "stt_m1" = "0x036b"
register "stt_m2" = "0x0022"
register "stt_c_apu" = "0xffc1"
register "stt_alpha_apu" = "0x199a"
# set usb3 port force to gen1
register "usb3_port_force_gen1" = "{
.ports.xhci0_port0 = 1,
.ports.xhci1_port0 = 1,
.ports.xhci1_port1 = 0,
}"
device domain 0 on
register "dxio_tx_vboost_enable" = "1"
device ref gpp_bridge_1 on
# Required so the NVMe gets placed into D3 when entering S0i3.
chip drivers/pcie/rtd3/device
register "name" = ""NVME""
device pci 00.0 on end
end
end # NVME
device ref gpp_bridge_2 on
# Required so the NVMe gets placed into D3 when entering S0i3.
chip drivers/pcie/rtd3/device
register "name" = ""NVME""
device pci 00.0 on end
end
end # NVME
device ref gpp_bridge_a on # Internal GPP Bridge 0 to Bus A
device ref xhci_1 on # XHCI1 controller
chip drivers/usb/acpi
device ref xhci_1_root_hub on # XHCI1 root hub
chip drivers/usb/acpi
register "desc" = ""USB3 Type-A Port A0 (MLB)""
register "type" = "UPC_TYPE_USB3_A"
register "use_custom_pld" = "true"
register "custom_pld" = "ACPI_PLD_TYPE_A(LEFT, RIGHT, ACPI_PLD_GROUP(2, 2))"
device ref usb3_port3 on end # USB 3.1 port3
end
chip drivers/usb/acpi
register "desc" = ""USB2 Type-A Port A0 (MLB)""
register "type" = "UPC_TYPE_USB3_A"
register "use_custom_pld" = "true"
register "custom_pld" = "ACPI_PLD_TYPE_A(LEFT, RIGHT, ACPI_PLD_GROUP(2, 2))"
device ref usb2_port3 on end # USB 2 port3
end
end # XHCI1 root hub
end
end # XHCI1 controller
end # Internal GPP Bridge 0 to Bus A
end # domain
device ref i2c_0 on
chip drivers/i2c/generic
register "hid" = ""ELAN0000""
register "desc" = ""ELAN Touchpad""
register "irq_gpio" = "ACPI_GPIO_IRQ_EDGE_LOW(GPIO_40)"
register "wake" = "GEVENT_20"
register "detect" = "1"
device i2c 15 on end
end
chip drivers/i2c/hid
register "generic.hid" = ""SYNA0000""
register "generic.cid" = ""ACPI0C50""
register "generic.desc" = ""Synaptics Touchpad""
register "generic.irq_gpio" = "ACPI_GPIO_IRQ_LEVEL_LOW(GPIO_40)"
register "generic.wake" = "GEVENT_20"
register "generic.detect" = "1"
register "hid_desc_reg_offset" = "0x20"
device i2c 2c on end
end
end # I2C0
device ref i2c_1 on
chip drivers/i2c/hid
register "generic.hid" = ""ELAN9004""
register "generic.desc" = ""ELAN Touchscreen""
register "generic.irq_gpio" = "ACPI_GPIO_IRQ_LEVEL_LOW(GPIO_29)"
register "generic.detect" = "1"
register "generic.enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPIO_131)"
register "generic.enable_delay_ms" = "10"
register "generic.reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPIO_136)"
register "generic.reset_off_delay_ms" = "1"
register "generic.reset_delay_ms" = "10"
register "generic.stop_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPIO_76)"
register "generic.stop_delay_ms" = "150"
register "generic.stop_off_delay_ms" = "1"
register "generic.has_power_resource" = "1"
register "hid_desc_reg_offset" = "0x01"
device i2c 10 on end
end
end # I2C1
device ref i2c_2 on
chip drivers/i2c/generic
register "hid" = ""RTL5682""
register "name" = ""RT58""
register "desc" = ""Realtek RT5682""
register "irq_gpio" = "ACPI_GPIO_IRQ_EDGE_BOTH(GPIO_90)"
register "property_count" = "1"
register "property_list[0].type" = "ACPI_DP_TYPE_INTEGER"
register "property_list[0].name" = ""realtek,jd-src""
register "property_list[0].integer" = "1"
device i2c 1a on end
end
chip drivers/i2c/generic
register "hid" = ""10EC1019""
register "desc" = ""Realtek SPK AMP R""
register "uid" = "1"
device i2c 29 on end
end
chip drivers/i2c/generic
register "hid" = ""10EC1019""
register "desc" = ""Realtek SPK AMP L""
register "uid" = "2"
register "probed" = "1"
device i2c 2a on end
end
end # I2C2
end # chip soc/amd/mendocino
|
