1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
277
278
279
280
281
282
283
284
285
286
287
288
289
290
291
292
293
294
295
296
297
298
299
300
301
302
303
304
305
306
307
308
309
310
311
312
313
314
315
316
317
318
319
320
321
322
323
324
325
326
327
328
329
330
331
332
333
334
335
336
337
338
339
340
341
342
343
344
345
346
347
348
349
350
351
352
353
354
355
356
357
358
359
360
361
362
363
364
365
366
367
368
369
370
371
372
373
374
375
376
377
378
379
380
381
382
383
384
385
386
387
388
389
390
391
392
393
394
395
396
397
398
399
400
401
402
403
404
405
406
407
408
409
410
|
chip soc/intel/cannonlake
# GPE configuration
# Note that GPE events called out in ASL code rely on this
# route. i.e. If this route changes then the affected GPE
# offset bits also need to be changed.
register "gpe0_dw0" = "PMC_GPP_A"
register "gpe0_dw1" = "PMC_GPP_C"
register "gpe0_dw2" = "PMC_GPP_D"
# EC host command ranges
register "gen1_dec" = "0x00040931" # 0x930-0x937
register "gen2_dec" = "0x00040941" # 0x940-0x947
register "gen3_dec" = "0x000c0951" # 0x950-0x95f
# FSP configuration
register "SaGv" = "SaGv_Enabled"
register "SataSalpSupport" = "1"
register "SataMode" = "Sata_AHCI"
register "SataPortsEnable[2]" = "1"
register "SataPortsDevSlp[2]" = "1"
register "InternalGfx" = "1"
register "SkipExtGfxScan" = "1"
register "PchPmSlpS3MinAssert" = "3" # 50ms
register "PchPmSlpS4MinAssert" = "4" # 4s
register "PchPmSlpSusMinAssert" = "4" # 4s
register "PchPmSlpAMinAssert" = "4" # 2s
register "PchUnlockGpioPads" = "1"
# USB2 PHY Power gating
register "PchUsb2PhySusPgDisable" = "1"
register "speed_shift_enable" = "1"
register "s0ix_enable" = "1"
register "dptf_enable" = "1"
register "satapwroptimize" = "1"
register "power_limits_config" = "{
.tdp_pl1_override = 25,
.tdp_pl2_override = 51,
.psys_pmax = 140,
}"
register "Device4Enable" = "1"
register "AcousticNoiseMitigation" = "1"
register "SlowSlewRateForIa" = "2"
register "SlowSlewRateForGt" = "2"
register "SlowSlewRateForSa" = "0"
register "SlowSlewRateForFivr" = "2"
# Enable eDP device
register "DdiPortEdp" = "1"
# Enable HPD for DDI ports B/C
register "DdiPortBHpd" = "1"
register "DdiPortCHpd" = "1"
# Enable DDC for DDI port B
register "DdiPortBDdc" = "1"
# VR Settings Configuration for 4 Domains
#+----------------+-------+-------+-------+-------+
#| Domain/Setting | SA | IA | GTUS | GTS |
#+----------------+-------+-------+-------+-------+
#| Psi1Threshold | 20A | 20A | 20A | 20A |
#| Psi2Threshold | 5A | 5A | 5A | 5A |
#| Psi3Threshold | 1A | 1A | 1A | 1A |
#| Psi3Enable | 1 | 1 | 1 | 1 |
#| Psi4Enable | 1 | 1 | 1 | 1 |
#| ImonSlope | 0 | 0 | 0 | 0 |
#| ImonOffset | 0 | 0 | 0 | 0 |
#| IccMax | 6A | 70A | 31A | 31A |
#| VrVoltageLimit | 1.52V | 1.52V | 1.52V | 1.52V |
#| AcLoadline | 10.3 | 1.8 | 3.1 | 3.1 |
#| DcLoadline | 10.3 | 1.8 | 3.1 | 3.1 |
#+----------------+-------+-------+-------+-------+
register "domain_vr_config[VR_SYSTEM_AGENT]" = "{
.vr_config_enable = 1,
.psi1threshold = VR_CFG_AMP(20),
.psi2threshold = VR_CFG_AMP(5),
.psi3threshold = VR_CFG_AMP(1),
.psi3enable = 1,
.psi4enable = 1,
.imon_slope = 0x0,
.imon_offset = 0x0,
.icc_max = VR_CFG_AMP(6),
.voltage_limit = 1520,
.ac_loadline = 1030,
.dc_loadline = 1030,
}"
register "domain_vr_config[VR_IA_CORE]" = "{
.vr_config_enable = 1,
.psi1threshold = VR_CFG_AMP(20),
.psi2threshold = VR_CFG_AMP(5),
.psi3threshold = VR_CFG_AMP(1),
.psi3enable = 1,
.psi4enable = 1,
.imon_slope = 0x0,
.imon_offset = 0x0,
.icc_max = VR_CFG_AMP(70),
.voltage_limit = 1520,
.ac_loadline = 180,
.dc_loadline = 180,
}"
register "domain_vr_config[VR_GT_UNSLICED]" = "{
.vr_config_enable = 1,
.psi1threshold = VR_CFG_AMP(20),
.psi2threshold = VR_CFG_AMP(5),
.psi3threshold = VR_CFG_AMP(1),
.psi3enable = 1,
.psi4enable = 1,
.imon_slope = 0x0,
.imon_offset = 0x0,
.icc_max = VR_CFG_AMP(31),
.voltage_limit = 1520,
.ac_loadline = 310,
.dc_loadline = 310,
}"
register "domain_vr_config[VR_GT_SLICED]" = "{
.vr_config_enable = 1,
.psi1threshold = VR_CFG_AMP(20),
.psi2threshold = VR_CFG_AMP(5),
.psi3threshold = VR_CFG_AMP(1),
.psi3enable = 1,
.psi4enable = 1,
.imon_slope = 0x0,
.imon_offset = 0x0,
.icc_max = VR_CFG_AMP(31),
.voltage_limit = 1520,
.ac_loadline = 310,
.dc_loadline = 310,
}"
# Intel Common SoC Config
register "usb2_ports[0]" = "USB2_PORT_TYPE_C(OC_SKIP)" # Left Type-C Port
register "usb2_ports[1]" = "USB2_PORT_LONG(OC0)" # Left Type-A Port
register "usb2_ports[2]" = "USB2_PORT_LONG(OC1)" # Right Type-A Port
register "usb2_ports[3]" = "USB2_PORT_EMPTY"
register "usb2_ports[4]" = "USB2_PORT_EMPTY"
register "usb2_ports[5]" = "USB2_PORT_LONG(OC_SKIP)" # Camera
register "usb2_ports[6]" = "{
.enable = 1, \
.ocpin = OC_SKIP, \
.tx_bias = USB2_BIAS_0MV, \
.tx_emp_enable = USB2_DE_EMP_ON_PRE_EMP_ON, \
.pre_emp_bias = USB2_BIAS_28P15MV, \
.pre_emp_bit = USB2_HALF_BIT_PRE_EMP, \
}" # WWAN
register "usb2_ports[7]" = "USB2_PORT_MID(OC_SKIP)" # USH
register "usb2_ports[8]" = "USB2_PORT_MID(OC_SKIP)" # Fingerprint
register "usb2_ports[9]" = "USB2_PORT_MID(OC_SKIP)" # Bluetooth
register "usb3_ports[0]" = "USB3_PORT_DEFAULT(OC_SKIP)" # Left Type-C Port
register "usb3_ports[1]" = "USB3_PORT_DEFAULT(OC0)" # Left Type-A Port
register "usb3_ports[2]" = "USB3_PORT_DEFAULT(OC1)" # Right Type-A Port
register "usb3_ports[3]" = "USB3_PORT_DEFAULT(OC_SKIP)" # WWAN
register "usb3_ports[4]" = "USB3_PORT_EMPTY"
register "usb3_ports[5]" = "USB3_PORT_EMPTY"
# Intel Common SoC Config
#+-------------------+---------------------------+
#| Field | Value |
#+-------------------+---------------------------+
#| chipset_lockdown | CHIPSET_LOCKDOWN_COREBOOT |
#| I2C0 | Touchscreen |
#| I2C1 | Touchpad |
#| I2C4 | H1 TPM |
#+-------------------+---------------------------+
register "tcc_offset" = "1"
# PCH Thermal Trip Temperature in deg C
register "common_soc_config.pch_thermal_trip" = "77"
register "common_soc_config" = "{
.chipset_lockdown = CHIPSET_LOCKDOWN_COREBOOT,
.i2c[0] = {
.speed = I2C_SPEED_FAST,
.rise_time_ns = 52,
.fall_time_ns = 110,
},
.i2c[1] = {
.speed = I2C_SPEED_FAST,
.rise_time_ns = 52,
.fall_time_ns = 110,
.data_hold_time_ns = 330,
},
.i2c[4] = {
.early_init = 1,
.speed = I2C_SPEED_FAST,
.rise_time_ns = 36,
.fall_time_ns = 99,
},
}"
# PCIe port 10 for M.2 2230 WLAN
register "PcieRpEnable[9]" = "1"
register "PcieClkSrcUsage[2]" = "9"
register "PcieClkSrcClkReq[2]" = "2"
# PCIe port 11 for card reader
register "PcieRpEnable[10]" = "1"
register "PcieRpLtrEnable[10]" = "1"
register "PcieClkSrcUsage[1]" = "10"
register "PcieClkSrcClkReq[1]" = "1"
# PCIe port 13 for M.2 2280 SSD
register "PcieRpEnable[12]" = "1"
register "PcieRpLtrEnable[12]" = "1"
register "PcieClkSrcUsage[4]" = "12"
register "PcieClkSrcClkReq[4]" = "4"
# GPIO PM programming
register "gpio_override_pm" = "1"
# GPIO community PM configuration
register "gpio_pm[COMM_0]" = "MISCCFG_ENABLE_GPIO_PM_CONFIG"
register "gpio_pm[COMM_1]" = "MISCCFG_GPSIDEDPCGEN | MISCCFG_GPRTCDLCGEN | MISCCFG_GSXSLCGEN | MISCCFG_GPDPCGEN | MISCCFG_GPDLCGEN"
register "gpio_pm[COMM_2]" = "MISCCFG_ENABLE_GPIO_PM_CONFIG"
register "gpio_pm[COMM_3]" = "MISCCFG_ENABLE_GPIO_PM_CONFIG"
register "gpio_pm[COMM_4]" = "MISCCFG_ENABLE_GPIO_PM_CONFIG"
device cpu_cluster 0 on
device lapic 0 on end
end
device domain 0 on
device pci 00.0 on end # Host Bridge
device pci 02.0 on end # Integrated Graphics Device
device pci 04.0 on end # SA Thermal device
device pci 12.0 on end # Thermal Subsystem
device pci 12.5 off end # UFS SCS
device pci 12.6 off end # GSPI #2
device pci 13.0 on # Integrated Sensor Hub
chip drivers/intel/ish
register "firmware_name" = ""arcada_ish.bin""
device generic 0 on end
end
end
device pci 14.0 on
chip drivers/usb/acpi
register "desc" = ""Root Hub""
register "type" = "UPC_TYPE_HUB"
device usb 0.0 on
chip drivers/usb/acpi
register "desc" = ""Left Type-C Port""
register "type" = "UPC_TYPE_C_USB2_SS_SWITCH"
register "group" = "ACPI_PLD_GROUP(1, 1)"
device usb 2.0 on end
end
chip drivers/usb/acpi
register "desc" = ""Left Type-A Port""
register "type" = "UPC_TYPE_A"
register "group" = "ACPI_PLD_GROUP(1, 2)"
device usb 2.1 on end
end
chip drivers/usb/acpi
register "desc" = ""Right Type-A Port""
register "type" = "UPC_TYPE_A"
register "group" = "ACPI_PLD_GROUP(2, 1)"
device usb 2.2 on end
end
chip drivers/usb/acpi
register "desc" = ""Camera""
register "type" = "UPC_TYPE_INTERNAL"
device usb 2.5 on end
end
chip drivers/usb/acpi
register "desc" = ""WWAN""
register "type" = "UPC_TYPE_INTERNAL"
device usb 2.6 on end
end
chip drivers/usb/acpi
register "desc" = ""USH""
register "type" = "UPC_TYPE_INTERNAL"
device usb 2.7 on end
end
chip drivers/usb/acpi
register "desc" = ""Fingerprint""
register "type" = "UPC_TYPE_INTERNAL"
device usb 2.8 on end
end
chip drivers/usb/acpi
register "desc" = ""Bluetooth""
register "type" = "UPC_TYPE_INTERNAL"
register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_H15)"
device usb 2.9 on end
end
chip drivers/usb/acpi
register "desc" = ""Left Type-C Port""
register "type" = "UPC_TYPE_C_USB2_SS_SWITCH"
register "group" = "ACPI_PLD_GROUP(1, 1)"
device usb 3.0 on end
end
chip drivers/usb/acpi
register "desc" = ""Left Type-A Port""
register "type" = "UPC_TYPE_USB3_A"
register "group" = "ACPI_PLD_GROUP(1, 2)"
device usb 3.1 on end
end
chip drivers/usb/acpi
register "desc" = ""Right Type-A Port""
register "type" = "UPC_TYPE_USB3_A"
register "group" = "ACPI_PLD_GROUP(2, 1)"
device usb 3.2 on end
end
chip drivers/usb/acpi
register "desc" = ""WWAN""
register "type" = "UPC_TYPE_INTERNAL"
device usb 3.3 on end
end
end
end
end # USB xHCI
device pci 14.1 off end # USB xDCI (OTG)
chip drivers/intel/wifi
register "wake" = "PME_B0_EN_BIT"
device pci 14.3 on end # CNVi wifi
end
device pci 14.5 off end # SDCard
device pci 15.0 on
chip drivers/i2c/hid
register "generic.hid" = ""WCOM48E2""
register "generic.desc" = ""Wacom Touchscreen""
register "generic.irq" = "ACPI_IRQ_LEVEL_LOW(GPP_C23_IRQ)"
register "generic.probed" = "1"
register "generic.reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_E7)"
register "generic.reset_delay_ms" = "120"
register "generic.enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_B21)"
register "generic.enable_delay_ms" = "55"
register "generic.has_power_resource" = "1"
register "generic.disable_gpio_export_in_crs" = "1"
register "hid_desc_reg_offset" = "0x1"
device i2c 0A on end
end
end # I2C #0
device pci 15.1 on
chip drivers/i2c/generic
register "hid" = ""ELAN0000""
register "desc" = ""ELAN Touchpad""
register "irq" = "ACPI_IRQ_EDGE_LOW(GPP_B3_IRQ)"
register "probed" = "1"
device i2c 2c on end
end
chip drivers/i2c/hid
register "generic.hid" = ""PNP0C50""
register "generic.desc" = ""Cirque Touchpad""
register "generic.irq" = "ACPI_IRQ_EDGE_LOW(GPP_B3_IRQ)"
register "generic.probed" = "1"
register "hid_desc_reg_offset" = "0x20"
device i2c 2a on end
end
end # I2C #1
device pci 15.2 off end # I2C #2
device pci 15.3 off end # I2C #3
device pci 16.0 off end # Management Engine Interface 1
device pci 16.1 off end # Management Engine Interface 2
device pci 16.2 off end # Management Engine IDE-R
device pci 16.3 off end # Management Engine KT Redirection
device pci 16.4 off end # Management Engine Interface 3
device pci 16.5 off end # Management Engine Interface 4
device pci 17.0 on end # SATA
device pci 19.0 on
chip drivers/i2c/tpm
register "hid" = ""GOOG0005""
register "irq" = "ACPI_IRQ_EDGE_LOW(GPP_D18_IRQ)"
device i2c 50 on end
end
end # I2C #4
device pci 19.1 off end # I2C #5
device pci 19.2 on end # UART #2
device pci 1a.0 off end # eMMC
device pci 1c.0 off end # PCI Express Port 1 (USB)
device pci 1c.1 off end # PCI Express Port 2 (USB)
device pci 1c.2 off end # PCI Express Port 3 (USB)
device pci 1c.3 off end # PCI Express Port 4 (USB)
device pci 1c.4 off end # PCI Express Port 5 (USB)
device pci 1c.5 off end # PCI Express Port 6
device pci 1c.6 off end # PCI Express Port 7
device pci 1c.7 off end # PCI Express Port 8
device pci 1d.0 off end # PCI Express Port 9
device pci 1d.1 on
smbios_slot_desc "SlotTypeM2Socket1_SD" "SlotLengthOther" "2230" "SlotDataBusWidth1X"
register "PcieRpSlotImplemented[9]" = "1"
end # PCI Express Port 10
device pci 1d.2 on # PCI Express Port 11
register "PcieRpSlotImplemented[10]" = "1"
end
device pci 1d.3 off end # PCI Express Port 12
device pci 1d.4 on
chip drivers/generic/bayhub
register "power_saving" = "1"
device pci 00.0 on end
end
smbios_slot_desc "SlotTypeM2Socket3" "SlotLengthOther" "2280" "SlotDataBusWidth4X"
register "PcieRpSlotImplemented[12]" = "1"
end # PCI Express Port 13 (x4)
device pci 1e.0 off end # UART #0
device pci 1e.1 off end # UART #1
device pci 1e.2 off end # GSPI #0
device pci 1e.3 off end # GSPI #1
device pci 1f.0 on
chip ec/google/wilco
device pnp 0c09.0 on end
end
end # LPC/eSPI
device pci 1f.1 on end # P2SB
device pci 1f.2 on end # Power Management Controller
device pci 1f.3 on end # Intel HDA
device pci 1f.4 on end # SMBus
device pci 1f.5 on end # PCH SPI
device pci 1f.6 off end # GbE
end
end
|
