blob: 55d9873fda99b2601eef747f9a2ee31c2cacdcb0 (
plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
|
chip soc/intel/baytrail
# SATA port enable mask (2 ports)
register "sata_port_map" = "0x1"
register "sata_ahci" = "0x1"
register "ide_legacy_combined" = "0x0"
# Route USB ports to XHCI
register "usb_route_to_xhci" = "1"
# USB Port Disable Mask
register "usb2_port_disable_mask" = "0x0"
register "usb3_port_disable_mask" = "0x0"
# USB PHY settings
# TODO: These values are from Baytrail and need tuned for Banjo board
register "usb2_per_port_lane0" = "0x00049a09"
register "usb2_per_port_rcomp_hs_pullup0" = "0x0300401d"
register "usb2_per_port_lane1" = "0x00049a09"
register "usb2_per_port_rcomp_hs_pullup1" = "0x0300401d"
register "usb2_per_port_lane2" = "0x00049209"
register "usb2_per_port_rcomp_hs_pullup2" = "0x01004015"
register "usb2_per_port_lane3" = "0x00049a09"
register "usb2_per_port_rcomp_hs_pullup3" = "0x0300401d"
# LPE audio codec settings
register "lpe_codec_clk_freq" = "25" # 25MHz clock
register "lpe_codec_clk_num" = "0" # PMC_PLT_CLK[0]
# SD Card controller
register "sdcard_cap_low" = "0x0"
register "sdcard_cap_high" = "0x0"
# Enable devices in ACPI mode
register "lpe_acpi_mode" = "1"
register "lpss_acpi_mode" = "1"
register "scc_acpi_mode" = "1"
# Allow PCIe devices to wake system from suspend
register "pcie_wake_enable" = "1"
# Enable PIPEA as DP_C
register "gpu_pipea_port_select" = "2" # DP_C
register "gpu_pipea_power_cycle_delay" = "6" # 600ms
register "gpu_pipea_power_on_delay" = "5000" # 500ms
register "gpu_pipea_light_on_delay" = "70" # 7ms
register "gpu_pipea_power_off_delay" = "500" # 50ms
register "gpu_pipea_light_off_delay" = "2000" # 200ms
# VR PS2 control
register "vnn_ps2_enable" = "1"
register "vcc_ps2_enable" = "1"
# Disable SLP_X stretching after SUS power well fail.
register "disable_slp_x_stretch_sus_fail" = "1"
device cpu_cluster 0 on
device lapic 0 on end
end
device domain 0 on
device pci 00.0 on end # SoC router
device pci 02.0 on end # GFX
device pci 11.0 off end # SDIO
device pci 12.0 off end # SD
device pci 13.0 on end # SATA
device pci 14.0 on end # XHCI
device pci 15.0 on end # LPE
device pci 17.0 on end # MMC
device pci 18.0 on end # SIO_DMA1
device pci 18.1 on end # I2C1
device pci 18.2 on end # I2C2
device pci 18.3 off end # I2C3
device pci 18.4 off end # I2C4
device pci 18.5 off end # I2C5
device pci 18.6 off end # I2C6
device pci 18.7 off end # I2C7
device pci 1a.0 off end # TXE
device pci 1b.0 on end # HDA
device pci 1c.0 on end # PCIE_PORT1
device pci 1c.1 off end # PCIE_PORT2
device pci 1c.2 off end # PCIE_PORT3
device pci 1c.3 off end # PCIE_PORT4
device pci 1d.0 on end # EHCI
device pci 1e.0 on end # SIO_DMA2
device pci 1e.1 off end # PWM1
device pci 1e.2 off end # PWM2
device pci 1e.3 off end # HSUART1
device pci 1e.4 off end # HSUART2
device pci 1e.5 off end # SPI
device pci 1f.0 on
chip drivers/pc80/tpm
device pnp 0c31.0 on end
end
chip ec/google/chromeec
# We only have one init function that
# we need to call to initialize the
# keyboard part of the EC.
device pnp ff.1 on # dummy address
end
end
end # LPC Bridge
device pci 1f.3 off end # SMBus
end
end
|
