1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
|
chip soc/intel/apollolake
# EMMC Tx CMD Delay
# Refer to EDS-Vol2-16.32.
# [14:8] steps of delay for DDR mode, each 125ps.
# [6:0] steps of delay for SDR mode, each 125ps.
register "emmc_tx_cmd_cntl" = "0x00000505"
# EMMC TX DATA Delay 1
# Refer to EDS-Vol2-16.33.
# [14:8] steps of delay for HS400, each 125ps.
# [6:0] steps of delay for SDR104/HS200, each 125ps.
register "emmc_tx_data_cntl1" = "0x00000c0d"
# EMMC TX DATA Delay 2
# Refer to EDS-Vol2-16.34.
# [30:24] steps of delay for SDR50, each 125ps.
# [22:16] steps of delay for DDR50, each 125ps.
# [14:8] steps of delay for SDR25/HS50, each 125ps.
# [6:0] steps of delay for SDR12, each 125ps.
register "emmc_tx_data_cntl2" = "0x1c2a2a2a"
# EMMC RX CMD/DATA Delay 1
# Refer to EDS-Vol2-16.35.
# [30:24] steps of delay for SDR50, each 125ps.
# [22:16] steps of delay for DDR50, each 125ps.
# [14:8] steps of delay for SDR25/HS50, each 125ps.
# [6:0] steps of delay for SDR12, each 125ps.
register "emmc_rx_cmd_data_cntl1" = "0x00181b1b"
# EMMC RX CMD/DATA Delay 2
# Refer to EDS-Vol2-16.37.
# [17:16] stands for Rx Clock before Output Buffer
# [14:8] steps of delay for Auto Tuning Mode, each 125ps.
# [6:0] steps of delay for HS200, each 125ps.
register "emmc_rx_cmd_data_cntl2" = "0x0001000f"
# EMMC Rx Strobe Delay
# Refer to EDS-Vol2-16.36.
# [14:8] Rx Strobe Delay DLL 1(HS400 Mode), each 125ps.
# [6:0] Rx Strobe Delay DLL 2(HS400 Mode), each 125ps.
register "emmc_rx_strobe_cntl" = "0x00000a0a"
# Override USB2 PER PORT register (PORT 4)
register "usb2eye[4]" = "{
.Usb20OverrideEn = 1,
.Usb20PerPortPeTxiSet = 7,
.Usb20PerPortTxiSet = 3,
.Usb20IUsbTxEmphasisEn = 3,
.Usb20PerPortTxPeHalf = 0,
}"
# Override USB2 PER PORT register (PORT 6)
register "usb2eye[6]" = "{
.Usb20OverrideEn = 1,
.Usb20PerPortPeTxiSet = 3,
.Usb20PerPortTxiSet = 0,
.Usb20IUsbTxEmphasisEn = 3,
.Usb20PerPortTxPeHalf = 0,
}"
# Intel Common SoC Config
#+-------------------+---------------------------+
#| Field | Value |
#+-------------------+---------------------------+
#| GSPI0 | cr50 TPM. Early init is |
#| | required to set up a BAR |
#| | for TPM communication |
#| | before memory is up |
#| I2C5 | Audio |
#| I2C6 | Trackpad |
#+-------------------+---------------------------+
register "common_soc_config" = "{
.gspi[0] = {
.speed_mhz = 1,
.early_init = 1,
},
.i2c[6] = {
.speed = I2C_SPEED_FAST,
.rise_time_ns = 66,
.fall_time_ns = 90,
.data_hold_time_ns = 350,
},
}"
device domain 0 on
device pci 15.0 on
chip drivers/usb/acpi
register "desc" = ""Root Hub""
register "type" = "UPC_TYPE_HUB"
device usb 0.0 on
chip drivers/usb/acpi
register "desc" = ""Right Type-A Port""
register "type" = "UPC_TYPE_A"
register "group" = "ACPI_PLD_GROUP(2, 2)"
device usb 2.1 on end
end
chip drivers/usb/acpi
device usb 2.3 off end
end
chip drivers/usb/acpi
register "desc" = ""Right Type-A Port""
register "type" = "UPC_TYPE_USB3_A"
register "group" = "ACPI_PLD_GROUP(2, 2)"
device usb 3.1 on end
end
chip drivers/usb/acpi
device usb 3.3 off end
end
end
end
end # - XHCI
device pci 17.1 on
chip drivers/i2c/da7219
register "irq" = "ACPI_IRQ_LEVEL_LOW(GPIO_137_IRQ)"
register "btn_cfg" = "50"
register "mic_det_thr" = "500"
register "jack_ins_deb" = "20"
register "jack_det_rate" = ""32ms_64ms""
register "jack_rem_deb" = "1"
register "a_d_btn_thr" = "0xa"
register "d_b_btn_thr" = "0x16"
register "b_c_btn_thr" = "0x21"
register "c_mic_btn_thr" = "0x3e"
register "btn_avg" = "4"
register "adc_1bit_rpt" = "1"
register "micbias_lvl" = "2600"
register "mic_amp_in_sel" = ""diff""
device i2c 1a on end
end
end # - I2C 5
device pci 17.2 on
chip drivers/i2c/generic
register "hid" = ""ELAN0000""
register "desc" = ""ELAN Touchpad""
register "irq" = "ACPI_IRQ_WAKE_EDGE_LOW(GPIO_135_IRQ)"
register "wake" = "GPE0_DW3_27"
register "probed" = "1"
device i2c 15 on end
end
chip drivers/i2c/hid
register "generic.hid" = ""ZNT0000""
register "generic.desc" = ""Zinitix Touchpad""
register "generic.irq" = "ACPI_IRQ_WAKE_LEVEL_LOW(GPIO_135_IRQ)"
register "generic.wake" = "GPE0_DW3_27"
register "generic.probed" = "1"
register "hid_desc_reg_offset" = "0xE"
device i2c 40 on end
end
end # - I2C 6
end
# Disable compliance mode
register "DisableComplianceMode" = "1"
end
|
