1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
277
278
279
280
281
282
283
284
285
286
287
288
289
290
291
292
293
294
|
chip soc/intel/apollolake
register "pcie_rp_clkreq_pin[2]" = "3" # wifi/bt
# Disable unused clkreq of PCIe root ports
register "pcie_rp_clkreq_pin[0]" = "CLKREQ_DISABLED"
register "pcie_rp_clkreq_pin[1]" = "CLKREQ_DISABLED"
register "pcie_rp_clkreq_pin[3]" = "CLKREQ_DISABLED"
register "pcie_rp_clkreq_pin[4]" = "CLKREQ_DISABLED"
register "pcie_rp_clkreq_pin[5]" = "CLKREQ_DISABLED"
# Set de-emphasis to disabled for PCIE WiFI (Thunderpeak)
# as it is required for detection
register "pcie_rp_deemphasis_enable[2]" = "0"
# Set de-emphasis to default (enabled) for remaining ports
register "pcie_rp_deemphasis_enable[0]" = "1"
register "pcie_rp_deemphasis_enable[1]" = "1"
register "pcie_rp_deemphasis_enable[3]" = "1"
register "pcie_rp_deemphasis_enable[4]" = "1"
register "pcie_rp_deemphasis_enable[5]" = "1"
# GPIO for PERST_0 (WLAN_PE_RST)
register "prt0_gpio" = "GPIO_164"
# GPE configuration
# Note that GPE events called out in ASL code rely on this
# route, i.e., if this route changes then the affected GPE
# offset bits also need to be changed. This sets the PMC register
# GPE_CFG fields.
# DW1 is used by:
# - GPIO_63 - H1_PCH_INT_ODL
# DW2 is used by:
# - GPIO_141 - EC_PCH_WAKE_ODL
# - GPIO_142 - TRACKPAD_INT2_1V8_ODL
# - GPIO_144 - PEN_EJECT_ODL
# DW3 is used by:
# - GPIO_117 - LTE_WAKE_ODL
# - GPIO_119 - WLAN_PCIE_WAKE_ODL
register "gpe0_dw1" = "PMC_GPE_NW_63_32"
register "gpe0_dw2" = "PMC_GPE_N_95_64"
register "gpe0_dw3" = "PMC_GPE_N_63_32"
# PL1 override 10 W: Due to error in the energy calculation for
# current VR solution. Experiments show that SoC TDP max (6W) can
# be reached when RAPL PL1 is set to 10W.
# Set RAPL PL2 to 15W.
register "power_limits_config" = "{
.tdp_pl1_override = 10,
.tdp_pl2_override = 15,
}"
# Minimum SLP S3 assertion width 28ms.
register "slp_s3_assertion_width_usecs" = "28000"
# Enable lpss s0ix
register "lpss_s0ix_enable" = "1"
# Enable DPTF
register "dptf_enable" = "1"
# Enable Audio Clock and Power gating
register "hdaudio_clk_gate_enable" = "1"
register "hdaudio_pwr_gate_enable" = "1"
register "hdaudio_bios_config_lockdown" = "1"
# Intel Common SoC Config
#+-------------------+---------------------------+
#| Field | Value |
#+-------------------+---------------------------+
#| GSPI0 | cr50 TPM. Early init is |
#| | required to set up a BAR |
#| | for TPM communication |
#| | before memory is up |
#| I2C0 | Digitizer |
#| I2C5 | Audio |
#| I2C6 | Trackpad |
#| I2C7 | Touchscreen |
#+-------------------+---------------------------+
register "common_soc_config" = "{
.gspi[0] = {
.speed_mhz = 1,
.early_init = 1,
},
.i2c[0] = {
.speed = I2C_SPEED_FAST,
.rise_time_ns = 152,
.fall_time_ns = 30,
},
.i2c[5] = {
.speed = I2C_SPEED_FAST,
.rise_time_ns = 104,
.fall_time_ns = 52,
},
.i2c[6] = {
.speed = I2C_SPEED_FAST,
.rise_time_ns = 114,
.fall_time_ns = 164,
.data_hold_time_ns = 350,
},
.i2c[7] = {
.speed = I2C_SPEED_FAST,
.rise_time_ns = 76,
.fall_time_ns = 164,
},
}"
register "pnp_settings" = "PNP_PERF_POWER"
device domain 0 on
device pci 00.0 on end # - Host Bridge
device pci 00.1 on end # - DPTF
device pci 00.2 off end # - NPK
device pci 02.0 on # - Gen
register "gfx" = "GMA_DEFAULT_PANEL(0)"
end
device pci 03.0 off end # - Gaussian Mixture Model (GMM)
device pci 0c.0 on
chip drivers/wifi/generic
register "wake" = "GPE0A_CNVI_PME_STS"
device generic 0 on end
end
end # - CNVi
device pci 0d.0 on end # - P2SB
device pci 0d.1 on end # - PMC
device pci 0d.2 on end # - Fast SPI
device pci 0d.3 on end # - Shared SRAM
device pci 0e.0 on
chip drivers/generic/max98357a
register "hid" = ""MX98357A""
register "sdmode_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPIO_91)"
register "sdmode_delay" = "5"
device generic 0 on end
end
end # - Audio
device pci 0f.0 on end # - Heci1
device pci 0f.1 on end # - Heci2
device pci 0f.2 on end # - Heci3
device pci 11.0 off end # - ISH
device pci 12.0 off end # - SATA
device pci 13.0 on
chip drivers/wifi/generic
register "wake" = "GPE0_DW3_11"
device pci 00.0 on end
end
end # - PCIe-A 0 Onboard M2 Slot(Wifi)
device pci 13.1 off end # - PCIe-A 1
device pci 13.2 off end # - PCIe-A 2
device pci 13.3 off end # - PCIe-A 3
device pci 14.0 off end # - PCIe-B 0
device pci 14.1 off end # - PCIe-B 1
device pci 15.0 on
chip drivers/usb/acpi
register "desc" = ""Root Hub""
register "type" = "UPC_TYPE_HUB"
device usb 0.0 on
chip drivers/usb/acpi
register "desc" = ""Left Type-C Port""
register "type" = "UPC_TYPE_C_USB2_SS_SWITCH"
register "group" = "ACPI_PLD_GROUP(1, 1)"
device usb 2.0 on end
end
chip drivers/usb/acpi
register "desc" = ""Left Type-A Port""
register "type" = "UPC_TYPE_A"
register "group" = "ACPI_PLD_GROUP(1, 2)"
device usb 2.1 on end
end
chip drivers/usb/acpi
register "desc" = ""Bluetooth""
register "type" = "UPC_TYPE_INTERNAL"
register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPIO_109)"
device usb 2.2 on end
end
chip drivers/usb/acpi
register "desc" = ""Right Type-A Port""
register "type" = "UPC_TYPE_A"
register "group" = "ACPI_PLD_GROUP(2, 2)"
device usb 2.3 on end
end
chip drivers/usb/acpi
register "desc" = ""Right Type-C Port""
register "type" = "UPC_TYPE_C_USB2_SS_SWITCH"
register "group" = "ACPI_PLD_GROUP(2, 1)"
device usb 2.4 on end
end
chip drivers/usb/acpi
register "desc" = ""SDCard""
register "type" = "UPC_TYPE_EXPRESSCARD"
device usb 2.5 on end
end
chip drivers/usb/acpi
register "desc" = ""User Facing Camera""
register "type" = "UPC_TYPE_INTERNAL"
device usb 2.6 on end
end
chip drivers/usb/acpi
register "desc" = ""World Facing Camera""
register "type" = "UPC_TYPE_INTERNAL"
device usb 2.7 on end
end
chip drivers/usb/acpi
register "desc" = ""Bluetooth""
register "type" = "UPC_TYPE_INTERNAL"
register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPIO_109)"
device usb 2.8 on end
end
chip drivers/usb/acpi
register "desc" = ""Left Type-C Port""
register "type" = "UPC_TYPE_C_USB2_SS_SWITCH"
register "group" = "ACPI_PLD_GROUP(1, 1)"
device usb 3.0 on end
end
chip drivers/usb/acpi
register "desc" = ""Left Type-A Port""
register "type" = "UPC_TYPE_USB3_A"
register "group" = "ACPI_PLD_GROUP(1, 2)"
device usb 3.1 on end
end
chip drivers/usb/acpi
register "desc" = ""Right Type-A Port""
register "type" = "UPC_TYPE_USB3_A"
register "group" = "ACPI_PLD_GROUP(2, 2)"
device usb 3.3 on end
end
chip drivers/usb/acpi
register "desc" = ""Right Type-C Port""
register "type" = "UPC_TYPE_C_USB2_SS_SWITCH"
register "group" = "ACPI_PLD_GROUP(2, 1)"
device usb 3.4 on end
end
chip drivers/usb/acpi
register "desc" = ""SDCard""
register "type" = "UPC_TYPE_EXPRESSCARD"
device usb 3.5 on end
end
end
end
end # - XHCI
device pci 15.1 off end # - XDCI
device pci 16.0 on end # - I2C 0
device pci 16.1 off end # - I2C 1
device pci 16.2 off end # - I2C 2
device pci 16.3 off end # - I2C 3
device pci 17.0 on end # - I2C 4
device pci 17.1 on end # - I2C 5
device pci 17.2 on end # - I2C 6
device pci 17.3 off end # - I2C 7
device pci 18.0 on end # - UART 0
device pci 18.1 off end # - UART 1
device pci 18.2 on end # - UART 2
device pci 18.3 off end # - UART 3
device pci 19.0 on
chip drivers/spi/acpi
register "hid" = "ACPI_DT_NAMESPACE_HID"
register "compat_string" = ""google,cr50""
register "irq" = "ACPI_IRQ_EDGE_LOW(GPIO_63_IRQ)"
device spi 0 on end
end
end # - GSPI 0
device pci 19.1 off end # - SPI 1
device pci 19.2 on end # - SPI 2
device pci 1a.0 on end # - PWM
device pci 1c.0 on end # - eMMC
device pci 1d.0 on end # - UFS
device pci 1e.0 off end # - SDIO
device pci 1f.0 on
chip ec/google/chromeec
device pnp 0c09.0 on end
end
end # - ESPI
device pci 1f.1 on end # - SMBUS
end
# FSP provides UPD interface to execute IPC command. PMIC has
# I2C_Slave_Address (31:24): 0x5E, Register_Offset (23:16): 0x43,
# RegOrValue (15:8): 0x2 and RegAndValue (7:0) 0xF8.
# The register is defined as: D[7:3] RSVD, D[2:0] PWROKDELAY.
# uint8 RegOrValue, RegAndValue, PmicReadReg
# RegOrValue = (UINT8)((PmicPmcIpcCtrl >> 8) & 0xff);
# RegAndValue = (UINT8)(PmicPmcIpcCtrl & 0xff);
# PmicReadReg &= RegAndValue;
# PmicReadReg |= RegOrValue;
# PmicReadReg value will be programmed into PMIC D[2:0] PWROKDELAY field
# and D[7:3] RSVD will not be impacted.
# Configure PmicPmcIpcCtrl for PMC to program PMIC PCH_PWROK delay
# from 100ms to 10ms.
# PWROKDELAY[2:0]: 000=2.5ms, 001=5.0ms, 010=10ms, 011=15ms, 100=20ms,
# 101=50ms, 110=75ms, 111=100ms (default)
register "PmicPmcIpcCtrl" = "0x5e4302f8"
# FSP UPD to modify the Integrated Filter (IF) value
# Set it to default value: 0x12
register "ModPhyIfValue" = "0x12"
end
|
