1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
|
# SPDX-License-Identifier: GPL-2.0-or-later
chip soc/amd/cezanne
register "system_configuration" = "3"
# eSPI Configuration
register "common_config.espi_config" = "{
.std_io_decode_bitmap = ESPI_DECODE_IO_0x80_EN | ESPI_DECODE_IO_0X60_0X64_EN,
.generic_io_range[0] = {
.base = 0x62,
/*
* Only 0x62 and 0x66 are required. But, this is not supported by
* standard IO decodes and there are only 4 generic I/O windows
* available. Hence, open a window from 0x62-0x67.
*/
.size = 5,
},
.generic_io_range[1] = {
.base = 0x800, /* EC_HOST_CMD_REGION0 */
.size = 256, /* EC_HOST_CMD_REGION_SIZE * 2 */
},
.generic_io_range[2] = {
.base = 0x900, /* EC_LPC_ADDR_MEMMAP */
.size = 255, /* EC_MEMMAP_SIZE */
},
.generic_io_range[3] = {
.base = 0x200, /* EC_LPC_ADDR_HOST_DATA */
.size = 8, /* 0x200 - 0x207 */
},
.io_mode = ESPI_IO_MODE_QUAD,
.op_freq_mhz = ESPI_OP_FREQ_33_MHZ,
.crc_check_enable = 1,
.dedicated_alert_pin = 1,
.periph_ch_en = 1,
.vw_ch_en = 1,
.oob_ch_en = 0,
.flash_ch_en = 0,
}"
register "i2c_scl_reset" = "GPIO_I2C0_SCL | GPIO_I2C1_SCL |
GPIO_I2C2_SCL | GPIO_I2C3_SCL"
device domain 0 on
device ref gpp_bridge_0 on end # WLAN
device ref gpp_bridge_1 on end # SD
device ref gpp_bridge_2 on end # LAN
device ref gpp_bridge_3 on end # NVMe
device ref gpp_bridge_a on # Internal GPP Bridge 0 to Bus A
device ref gfx on end # Internal GPU (GFX)
device ref xhci_0 on # USB 3.1 (USB0)
chip drivers/usb/acpi
device ref xhci_0_root_hub on
chip drivers/usb/acpi
register "desc" = ""Rear Type-C Port""
register "type" = "UPC_TYPE_C_USB2_SS_SWITCH"
register "group" = "ACPI_PLD_GROUP(1, 1)"
device ref usb3_port0 on end
end
chip drivers/usb/acpi
register "desc" = ""Front Type-A Port""
register "type" = "UPC_TYPE_USB3_A"
register "group" = "ACPI_PLD_GROUP(1, 2)"
device ref usb3_port1 on end
end
chip drivers/usb/acpi
register "desc" = ""Rear Type-C Port""
register "type" = "UPC_TYPE_C_USB2_SS_SWITCH"
register "group" = "ACPI_PLD_GROUP(1, 1)"
device ref usb2_port0 on end
end
chip drivers/usb/acpi
register "desc" = ""Front Type-A Port""
register "type" = "UPC_TYPE_USB3_A"
register "group" = "ACPI_PLD_GROUP(1, 2)"
device ref usb2_port1 on end
end
end
end
end
device ref xhci_1 on # USB 3.1 (USB1)
chip drivers/usb/acpi
device ref xhci_1_root_hub on
chip drivers/usb/acpi
register "desc" = ""Front Type-C Port""
register "type" = "UPC_TYPE_C_USB2_SS_SWITCH"
register "group" = "ACPI_PLD_GROUP(2, 2)"
device ref usb3_port4 on end
end
chip drivers/usb/acpi
register "desc" = ""USB HUB""
register "type" = "UPC_TYPE_USB3_A"
register "group" = "ACPI_PLD_GROUP(2, 1)"
device ref usb3_port5 on end
end
chip drivers/usb/acpi
register "desc" = ""Front Type-C Port""
register "type" = "UPC_TYPE_C_USB2_SS_SWITCH"
register "group" = "ACPI_PLD_GROUP(2, 2)"
device ref usb2_port4 on end
end
chip drivers/usb/acpi
register "desc" = ""USB HUB""
register "type" = "UPC_TYPE_USB3_A"
register "group" = "ACPI_PLD_GROUP(2, 1)"
device ref usb2_port5 on end
end
chip drivers/usb/acpi
register "desc" = ""Bluetooth""
register "type" = "UPC_TYPE_INTERNAL"
register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPIO_132)"
device ref usb2_port6 on end
end
end
end
end
end
device ref lpc_bridge on
chip ec/google/chromeec
device pnp 0c09.0 on end
end
end
device ref i2c_3 on
chip drivers/i2c/tpm
register "hid" = ""GOOG0005""
register "desc" = ""Cr50 TPM""
register "irq_gpio" = "ACPI_GPIO_IRQ_EDGE_LOW(GPIO_3)"
device i2c 50 on end
end
end
end # domain
device ref uart_0 on end # UART0
end # chip soc/amd/cezanne
|
