1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
277
278
279
280
281
282
283
284
285
286
287
288
289
290
291
292
293
294
295
296
297
298
299
300
301
302
303
304
305
306
307
308
309
310
311
312
313
314
315
316
317
318
319
320
321
|
chip soc/intel/cannonlake
# GPE configuration
# Note that GPE events called out in ASL code rely on this
# route. i.e. If this route changes then the affected GPE
# offset bits also need to be changed.
# DW1 is used by:
# - GPP_C1 - PCIE_14_WLAN_WAKE_ODL
# - GPP_C21 - H1_PCH_INT_ODL
register "gpe0_dw0" = "PMC_GPP_A"
register "gpe0_dw1" = "PMC_GPP_C"
register "gpe0_dw2" = "PMC_GPP_D"
# EC host command ranges are in 0x800-0x8ff & 0x200-0x20f
register "gen1_dec" = "0x00fc0801"
register "gen2_dec" = "0x000c0201"
# EC memory map range is 0x900-0x9ff
register "gen3_dec" = "0x00fc0901"
# FSP configuration
register "SkipExtGfxScan" = "1"
register "SataSalpSupport" = "1"
register "SataPortsEnable[1]" = "1"
register "SataPortsDevSlp[1]" = "1"
# Configure devslp pad reset to PLT_RST
register "SataPortsDevSlpResetConfig[1]" = "SataDevSlpPlatformReset"
register "satapwroptimize" = "1"
# Enable System Agent dynamic frequency
register "SaGv" = "SaGv_Enabled"
# Enable S0ix
register "s0ix_enable" = "1"
# Enable DPTF
register "dptf_enable" = "1"
register "power_limits_config" = "{
.tdp_pl1_override = 15,
.tdp_pl2_override = 64,
}"
register "Device4Enable" = "1"
# Enable eDP device
register "DdiPortEdp" = "1"
# Enable HPD for DDI ports B/C
register "DdiPortBHpd" = "1"
register "DdiPortCHpd" = "1"
register "tcc_offset" = "10" # TCC of 90C
# Unlock GPIO pads
register "PchUnlockGpioPads" = "1"
# SD card WP pin configuration
register "ScsSdCardWpPinEnabled" = "0"
# NOTE: if any variant wants to override this value, use the same format
# as register "common_soc_config.pch_thermal_trip" = "value", instead of
# putting it under register "common_soc_config" in overridetree.cb file.
register "common_soc_config.pch_thermal_trip" = "77"
# Select CPU PL2/PL4 config
register "cpu_pl2_4_cfg" = "baseline"
# VR Settings Configuration for 4 Domains
#+----------------+-------+-------+-------+-------+
#| Domain/Setting | SA | IA | GTUS | GTS |
#+----------------+-------+-------+-------+-------+
#| Psi1Threshold | 20A | 20A | 20A | 20A |
#| Psi2Threshold | 5A | 5A | 5A | 5A |
#| Psi3Threshold | 1A | 1A | 1A | 1A |
#| Psi3Enable | 1 | 1 | 1 | 1 |
#| Psi4Enable | 1 | 1 | 1 | 1 |
#| ImonSlope | 0 | 0 | 0 | 0 |
#| ImonOffset | 0 | 0 | 0 | 0 |
#| IccMax | 6A | 70A | 31A | 31A |
#| VrVoltageLimit | 1.52V | 1.52V | 1.52V | 1.52V |
#| AcLoadline | 10.3 | 1.8 | 3.1 | 3.1 |
#| DcLoadline | 10.3 | 1.8 | 3.1 | 3.1 |
#+----------------+-------+-------+-------+-------+
register "domain_vr_config[VR_SYSTEM_AGENT]" = "{
.vr_config_enable = 1,
.psi1threshold = VR_CFG_AMP(20),
.psi2threshold = VR_CFG_AMP(5),
.psi3threshold = VR_CFG_AMP(1),
.psi3enable = 1,
.psi4enable = 1,
.imon_slope = 0x0,
.imon_offset = 0x0,
.icc_max = 0,
.voltage_limit = 1520,
.ac_loadline = 1030,
.dc_loadline = 1030,
}"
register "domain_vr_config[VR_IA_CORE]" = "{
.vr_config_enable = 1,
.psi1threshold = VR_CFG_AMP(20),
.psi2threshold = VR_CFG_AMP(5),
.psi3threshold = VR_CFG_AMP(1),
.psi3enable = 1,
.psi4enable = 1,
.imon_slope = 0x0,
.imon_offset = 0x0,
.icc_max = 0,
.voltage_limit = 1520,
.ac_loadline = 180,
.dc_loadline = 180,
}"
register "domain_vr_config[VR_GT_UNSLICED]" = "{
.vr_config_enable = 1,
.psi1threshold = VR_CFG_AMP(20),
.psi2threshold = VR_CFG_AMP(5),
.psi3threshold = VR_CFG_AMP(1),
.psi3enable = 1,
.psi4enable = 1,
.imon_slope = 0x0,
.imon_offset = 0x0,
.icc_max = 0,
.voltage_limit = 1520,
.ac_loadline = 310,
.dc_loadline = 310,
}"
register "domain_vr_config[VR_GT_SLICED]" = "{
.vr_config_enable = 1,
.psi1threshold = VR_CFG_AMP(20),
.psi2threshold = VR_CFG_AMP(5),
.psi3threshold = VR_CFG_AMP(1),
.psi3enable = 1,
.psi4enable = 1,
.imon_slope = 0x0,
.imon_offset = 0x0,
.icc_max = 0,
.voltage_limit = 1520,
.ac_loadline = 310,
.dc_loadline = 310,
}"
register "PchPmSlpS3MinAssert" = "2" # 50ms
register "PchPmSlpS4MinAssert" = "1" # 1s
register "PchPmSlpSusMinAssert" = "1" # 500ms
register "PchPmSlpAMinAssert" = "3" # 98ms
# NOTE: Duration programmed in the below register should never be smaller than the
# stretch duration programmed in the following registers -
# - GEN_PMCON_A.SLP_S3_MIN_ASST_WDTH (PchPmSlpS3MinAssert)
# - GEN_PMCON_A.S4MAW (PchPmSlpS4MinAssert)
# - PM_CFG.SLP_A_MIN_ASST_WDTH (PchPmSlpAMinAssert)
# - PM_CFG.SLP_LAN_MIN_ASST_WDTH
register "PchPmPwrCycDur" = "1" # 1s
# Enable Audio DSP oscillator qualification for S0ix
register "cppmvric2_adsposcdis" = "1"
register "usb2_ports[0]" = "USB2_PORT_TYPE_C(OC2)" # Type-C Port 0
register "usb2_ports[1]" = "USB2_PORT_TYPE_C(OC2)" # Type-C Port 1
register "usb2_ports[2]" = "USB2_PORT_SHORT(OC3)" # Type-A Port 0
register "usb2_ports[3]" = "USB2_PORT_LONG(OC3)" # Type-A Port 1
register "usb2_ports[5]" = "USB2_PORT_MID(OC_SKIP)" # WWAN
register "usb2_ports[6]" = "USB2_PORT_LONG(OC_SKIP)" # Camera
register "usb2_ports[9]" = "USB2_PORT_MID(OC_SKIP)" # BT
register "usb3_ports[0]" = "USB3_PORT_DEFAULT(OC2)" # Type-C Port 0
register "usb3_ports[1]" = "USB3_PORT_DEFAULT(OC2)" # Type-C Port 1
register "usb3_ports[2]" = "USB3_PORT_DEFAULT(OC3)" # Type-A Port 0
register "usb3_ports[3]" = "USB3_PORT_DEFAULT(OC3)" # Type-A Port 1
register "usb3_ports[4]" = "USB3_PORT_DEFAULT(OC_SKIP)" # WWAN
# Enable Root port 9(x4) for NVMe.
register "PcieRpEnable[8]" = "1"
register "PcieRpLtrEnable[8]" = "1"
# RP 9 uses CLK SRC 1
register "PcieClkSrcUsage[1]" = "8"
# ClkReq-to-ClkSrc mapping for CLK SRC 1
register "PcieClkSrcClkReq[1]" = "1"
# PCIe port 14 for M.2 E-key WLAN
register "PcieRpEnable[13]" = "1"
register "PcieRpLtrEnable[13]" = "1"
# RP 14 uses CLK SRC 3
register "PcieClkSrcUsage[3]" = "13"
register "PcieClkSrcClkReq[3]" = "3"
#Enable I2S Audio, SSP0, SSP1 and DMIC0, default DMIC1 N/A (by variants override)
register "PchHdaDspEnable" = "1"
register "PchHdaAudioLinkSsp0" = "1"
register "PchHdaAudioLinkSsp1" = "1"
register "PchHdaAudioLinkDmic0" = "1"
register "PchHdaAudioLinkDmic1" = "0"
# GPIO PM programming
register "gpio_override_pm" = "1"
# GPIO community PM configuration
# Disable dynamic clock gating; with bits 0-5 set in these registers,
# some short interrupt pulses were missed (esp. cr50 irq)
register "gpio_pm[COMM_0]" = "0"
register "gpio_pm[COMM_1]" = "0"
register "gpio_pm[COMM_2]" = "0"
register "gpio_pm[COMM_3]" = "0"
register "gpio_pm[COMM_4]" = "0"
device domain 0 on
device ref igpu on end
device ref thermal on end
device ref xhci on
chip drivers/usb/acpi
device ref xhci_root_hub on
chip drivers/usb/acpi
register "desc" = ""Left Type-C Port""
register "type" = "UPC_TYPE_C_USB2_SS_SWITCH"
register "group" = "ACPI_PLD_GROUP(1, 1)"
device ref usb2_port1 on end
end
chip drivers/usb/acpi
register "desc" = ""Right Type-C Port 1""
register "type" = "UPC_TYPE_C_USB2_SS_SWITCH"
register "group" = "ACPI_PLD_GROUP(2, 1)"
device ref usb2_port2 on end
end
chip drivers/usb/acpi
register "desc" = ""Left Type-A Port""
register "type" = "UPC_TYPE_A"
register "group" = "ACPI_PLD_GROUP(1, 2)"
device ref usb2_port3 on end
end
chip drivers/usb/acpi
register "desc" = ""Right Type-A Port 1""
register "type" = "UPC_TYPE_A"
register "group" = "ACPI_PLD_GROUP(2, 2)"
device ref usb2_port4 on end
end
chip drivers/usb/acpi
register "desc" = ""WWAN""
register "type" = "UPC_TYPE_INTERNAL"
device ref usb2_port6 on end
end
chip drivers/usb/acpi
register "desc" = ""Camera""
register "type" = "UPC_TYPE_INTERNAL"
device ref usb2_port7 on end
end
chip drivers/usb/acpi
register "desc" = ""Bluetooth""
register "type" = "UPC_TYPE_INTERNAL"
register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C14)"
device ref usb2_port10 on end
end
chip drivers/usb/acpi
register "desc" = ""Left Type-C Port""
register "type" = "UPC_TYPE_C_USB2_SS_SWITCH"
register "group" = "ACPI_PLD_GROUP(1, 1)"
device ref usb3_port1 on end
end
chip drivers/usb/acpi
register "desc" = ""Right Type-C Port 1""
register "type" = "UPC_TYPE_C_USB2_SS_SWITCH"
register "group" = "ACPI_PLD_GROUP(2, 1)"
device ref usb3_port2 on end
end
chip drivers/usb/acpi
register "desc" = ""Left Type-A Port""
register "type" = "UPC_TYPE_USB3_A"
register "group" = "ACPI_PLD_GROUP(1, 2)"
device ref usb3_port3 on end
end
chip drivers/usb/acpi
register "desc" = ""Right Type-A Port 1""
register "type" = "UPC_TYPE_USB3_A"
register "group" = "ACPI_PLD_GROUP(2, 2)"
device ref usb3_port4 on end
end
chip drivers/usb/acpi
register "desc" = ""WWAN""
register "type" = "UPC_TYPE_INTERNAL"
device ref usb3_port5 on end
end
end
end
end # USB xHCI
device ref cnvi_wifi on
chip drivers/wifi/generic
register "wake" = "GPE0_PME_B0"
device generic 0 on end
end
end
device ref i2c0 on end
device ref i2c1 on end
device ref sata on end
device ref i2c4 on end
device ref pcie_rp9 on
register "PcieRpSlotImplemented[8]" = "1"
end # (x4 NVMe)
device ref pcie_rp14 on
chip drivers/wifi/generic
register "wake" = "GPE0_DW1_01"
device generic 0 on end
end
register "PcieRpSlotImplemented[13]" = "1"
end # (x1 WiFi)
device ref uart0 on end
device ref gspi0 on
chip drivers/spi/acpi
register "hid" = "ACPI_DT_NAMESPACE_HID"
register "compat_string" = ""google,cr50""
register "irq" = "ACPI_IRQ_EDGE_LOW(GPP_C21_IRQ)"
device spi 0 on end
end
end
device ref lpc_espi on
chip ec/google/chromeec
device pnp 0c09.0 on end
end
end
device ref p2sb on end
device ref hda on
chip drivers/sof
register "spkr_tplg" = "max98357a"
register "jack_tplg" = "rt5682"
register "mic_tplg" = "_2ch_pdm0"
device generic 0 on end
end
end
device ref smbus on end
end
end
|
