1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
277
278
279
280
281
282
283
284
285
286
287
288
289
290
291
292
293
294
295
296
297
298
299
300
301
302
303
304
305
306
307
308
309
310
311
312
313
314
315
316
317
318
319
320
321
322
323
324
325
326
327
328
329
330
331
332
333
334
335
336
337
338
339
340
341
342
343
344
345
346
347
348
349
350
351
352
353
354
355
356
357
358
359
360
361
362
363
364
365
366
367
368
369
370
371
372
373
374
375
376
377
378
379
380
381
382
383
384
385
386
387
388
389
390
391
392
393
394
395
396
397
398
399
400
401
402
403
404
405
406
407
408
409
410
411
412
413
414
415
416
417
418
419
420
421
|
fw_config
field DB_USB 0 2
option USB_ABSENT 0
option USB3_PS8815 1
option USB4_KB8001 2
end
field STYLUS 5
option STYLUS_ABSENT 0
option STYLUS_PRESENT 1
end
field AUDIO_AMP 7 9
option UNPROVISIONED 0
option MAX98360_ALC5682I_I2S 1
option MAX98360_ALC5682VS_I2S_2WAY 2
end
end
chip soc/intel/alderlake
register "SaGv" = "SaGv_Enabled"
# FIVR configurations for brya are disabled since the board doesn't have V1p05 and Vnn
# bypass rails implemented.
register "ext_fivr_settings" = "{
.configure_ext_fivr = 1,
}"
register "usb2_ports[0]" = "USB2_PORT_EMPTY"
register "usb2_ports[3]" = "USB2_PORT_EMPTY"
register "usb3_ports[3]" = "USB3_PORT_EMPTY"
register "tcss_ports[0]" = "TCSS_PORT_EMPTY"
register "SerialIoI2cMode" = "{
[PchSerialIoIndexI2C0] = PchSerialIoPci,
[PchSerialIoIndexI2C1] = PchSerialIoPci,
[PchSerialIoIndexI2C2] = PchSerialIoDisabled,
[PchSerialIoIndexI2C3] = PchSerialIoPci,
[PchSerialIoIndexI2C4] = PchSerialIoDisabled,
[PchSerialIoIndexI2C5] = PchSerialIoPci,
}"
register "SerialIoGSpiMode" = "{
[PchSerialIoIndexGSPI0] = PchSerialIoDisabled,
[PchSerialIoIndexGSPI1] = PchSerialIoDisabled,
}"
# Intel Common SoC Config
#+-------------------+---------------------------+
#| Field | Value |
#+-------------------+---------------------------+
#| I2C0 | Audio |
#| I2C1 | cr50 TPM. Early init is |
#| | required to set up a BAR |
#| | for TPM communication |
#| I2C3 | Touchscreen |
#| I2C5 | Trackpad |
#+-------------------+---------------------------+
register "common_soc_config" = "{
.i2c[0] = {
.speed = I2C_SPEED_FAST,
},
.i2c[1] = {
.early_init = 1,
.speed = I2C_SPEED_FAST,
},
.i2c[3] = {
.speed = I2C_SPEED_FAST,
},
.i2c[5] = {
.speed = I2C_SPEED_FAST,
},
}"
device domain 0 on
device ref dtt on
chip drivers/intel/dptf
## sensor information
register "options.tsr[0].desc" = ""DRAM_SOC""
register "options.tsr[1].desc" = ""Ambient""
register "options.tsr[2].desc" = ""Charger""
register "options.tsr[3].desc" = ""WWAN""
## Active Policy
register "policies.active" = "{
[0] = {
.target = DPTF_CPU,
.thresholds = {
TEMP_PCT(55, 65),
TEMP_PCT(52, 59),
TEMP_PCT(49, 50),
TEMP_PCT(46, 43),
TEMP_PCT(43, 37),
}
},
[1] = {
.target = DPTF_TEMP_SENSOR_1,
.thresholds = {
TEMP_PCT(55, 65),
TEMP_PCT(52, 59),
TEMP_PCT(49, 50),
TEMP_PCT(46, 43),
TEMP_PCT(43, 37),
}
}
}"
## Passive Policy
register "policies.passive" = "{
[0] = DPTF_PASSIVE(CPU, CPU, 95, 5000),
[1] = DPTF_PASSIVE(CPU, TEMP_SENSOR_0, 75, 5000),
[2] = DPTF_PASSIVE(CPU, TEMP_SENSOR_1, 75, 5000),
[3] = DPTF_PASSIVE(CHARGER, TEMP_SENSOR_2, 75, 5000),
[4] = DPTF_PASSIVE(CPU, TEMP_SENSOR_3, 75, 5000),
}"
## Critical Policy
register "policies.critical" = "{
[0] = DPTF_CRITICAL(CPU, 105, SHUTDOWN),
[1] = DPTF_CRITICAL(TEMP_SENSOR_0, 85, SHUTDOWN),
[2] = DPTF_CRITICAL(TEMP_SENSOR_1, 85, SHUTDOWN),
[3] = DPTF_CRITICAL(TEMP_SENSOR_2, 85, SHUTDOWN),
[4] = DPTF_CRITICAL(TEMP_SENSOR_3, 85, SHUTDOWN),
}"
register "controls.power_limits" = "{
.pl1 = {
.min_power = 13000,
.max_power = 15000,
.time_window_min = 28 * MSECS_PER_SEC,
.time_window_max = 28 * MSECS_PER_SEC,
.granularity = 200,
},
.pl2 = {
.min_power = 55000,
.max_power = 55000,
.time_window_min = 32 * MSECS_PER_SEC,
.time_window_max = 32 * MSECS_PER_SEC,
.granularity = 1000,
}
}"
## Charger Performance Control (Control, mA)
register "controls.charger_perf" = "{
[0] = { 255, 1700 },
[1] = { 24, 1500 },
[2] = { 16, 1000 },
[3] = { 8, 500 }
}"
## Fan Performance Control (Percent, Speed, Noise, Power)
register "controls.fan_perf" = "{
[0] = { 90, 6700, 220, 2200, },
[1] = { 80, 5800, 180, 1800, },
[2] = { 70, 5000, 145, 1450, },
[3] = { 60, 4900, 115, 1150, },
[4] = { 50, 3838, 90, 900, },
[5] = { 40, 2904, 55, 550, },
[6] = { 30, 2337, 30, 300, },
[7] = { 20, 1608, 15, 150, },
[8] = { 10, 800, 10, 100, },
[9] = { 0, 0, 0, 50, }
}"
## Fan options
register "options.fan.fine_grained_control" = "1"
register "options.fan.step_size" = "2"
device generic 0 alias dptf_policy on end
end
end
device ref tbt_pcie_rp0 off end
device ref tbt_pcie_rp1 on
probe DB_USB USB4_KB8001
end
device ref tbt_pcie_rp2 on
probe DB_USB USB4_KB8001
end
device ref cnvi_wifi on
chip drivers/wifi/generic
register "wake" = "GPE0_PME_B0"
device generic 0 on end
end
end
device ref tcss_dma0 on
probe DB_USB USB4_KB8001
chip drivers/intel/usb4/retimer
register "dfp[0].power_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_E4)"
use tcss_usb3_port2 as dfp[0].typec_port
device generic 0 on end
end
end
device ref tcss_dma1 on
probe DB_USB USB4_KB8001
chip drivers/intel/usb4/retimer
register "dfp[0].power_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_E4)"
use tcss_usb3_port3 as dfp[0].typec_port
device generic 0 on end
end
end
device ref pcie_rp6 off end
device ref pcie_rp8 on
chip soc/intel/common/block/pcie/rtd3
register "enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_H13)"
register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_D18)"
register "srcclk_pin" = "3"
device generic 0 on end
end
end #PCIE8 SD card
device ref i2c0 on
chip drivers/i2c/generic
register "hid" = ""10EC5682""
register "name" = ""RT58""
register "desc" = ""Headset Codec""
register "irq_gpio" = "ACPI_GPIO_IRQ_EDGE_BOTH(GPP_A23)"
# Set the jd_src to RT5668_JD1 for jack detection
register "property_count" = "1"
register "property_list[0].type" = "ACPI_DP_TYPE_INTEGER"
register "property_list[0].name" = ""realtek,jd-src""
register "property_list[0].integer" = "1"
device i2c 1a on
probe AUDIO_AMP MAX98360_ALC5682I_I2S
end
end
chip drivers/i2c/generic
register "hid" = ""RTL5682""
register "name" = ""RT58""
register "desc" = ""Headset Codec""
register "irq_gpio" = "ACPI_GPIO_IRQ_EDGE_BOTH(GPP_A23)"
# Set the jd_src to RT5668_JD1 for jack detection
register "property_count" = "1"
register "property_list[0].type" = "ACPI_DP_TYPE_INTEGER"
register "property_list[0].name" = ""realtek,jd-src""
register "property_list[0].integer" = "1"
device i2c 1a on
probe AUDIO_AMP MAX98360_ALC5682VS_I2S_2WAY
end
end
end #I2C0
device ref i2c1 on
chip drivers/i2c/tpm
register "hid" = ""GOOG0005""
register "irq" = "ACPI_IRQ_EDGE_LOW(GPP_A13_IRQ)"
device i2c 50 on end
end
end #I2C1
device ref i2c3 on
chip drivers/i2c/hid
register "generic.hid" = ""ELAN9008""
register "generic.desc" = ""ELAN Touchscreen""
register "generic.irq" = "ACPI_IRQ_LEVEL_LOW(GPP_C7_IRQ)"
register "generic.probed" = "1"
register "generic.reset_gpio" =
"ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C1)"
register "generic.reset_delay_ms" = "300"
register "generic.reset_off_delay_ms" = "1"
register "generic.enable_gpio" =
"ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_C0)"
register "generic.enable_delay_ms" = "6"
register "generic.stop_gpio" =
"ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C6)"
register "generic.stop_off_delay_ms" = "1"
register "generic.has_power_resource" = "1"
register "generic.disable_gpio_export_in_crs" = "1"
register "hid_desc_reg_offset" = "0x01"
device i2c 10 on end
end
chip drivers/generic/gpio_keys
register "name" = ""PENH""
register "gpio" = "ACPI_GPIO_IRQ_EDGE_BOTH(GPP_A7)"
register "key.wake_gpe" = "GPE0_DW0_08"
register "key.wakeup_route" = "WAKEUP_ROUTE_SCI"
register "key.wakeup_event_action" = "EV_ACT_ASSERTED"
register "key.dev_name" = ""EJCT""
register "key.linux_code" = "SW_PEN_INSERTED"
register "key.linux_input_type" = "EV_SW"
register "key.label" = ""pen_eject""
device generic 0 on
probe STYLUS STYLUS_PRESENT
end
end
end #I2C3
device ref i2c5 on
chip drivers/i2c/generic
register "hid" = ""ELAN0000""
register "desc" = ""ELAN Touchpad""
register "irq" = "ACPI_IRQ_WAKE_LEVEL_LOW(GPP_F14_IRQ)"
register "wake" = "GPE0_DW2_14"
register "probed" = "1"
device i2c 15 on end
end
end #I2C5
device ref hda on
chip drivers/generic/max98357a
register "hid" = ""MX98360A""
register "sdmode_gpio" =
"ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_A11)"
register "sdmode_delay" = "5"
device generic 0 on end
end
end
device ref pch_espi on
chip ec/google/chromeec
use conn1 as mux_conn[1]
use conn2 as mux_conn[0]
device pnp 0c09.0 on end
end
end
device ref pmc hidden
chip drivers/intel/pmc_mux
device generic 0 on
chip drivers/intel/pmc_mux/conn
use usb2_port3 as usb2_port
use tcss_usb3_port3 as usb3_port
device generic 2 alias conn2 on end
end
chip drivers/intel/pmc_mux/conn
use usb2_port2 as usb2_port
use tcss_usb3_port2 as usb3_port
device generic 1 alias conn1 on end
end
end
end
end
device ref tcss_xhci on
chip drivers/usb/acpi
device ref tcss_root_hub on
chip drivers/usb/acpi
register "desc" = ""USB3 Type-C Port C1 (DB)""
register "type" = "UPC_TYPE_C_USB2_SS_SWITCH"
register "use_custom_pld" = "true"
register "custom_pld" = "{
.visible = true,
.panel = PLD_PANEL_RIGHT,
.horizontal_position = PLD_HORIZONTAL_POSITION_LEFT,
.shape = PLD_SHAPE_OVAL,
.group = ACPI_PLD_GROUP(1, 1)}"
device ref tcss_usb3_port2 on end
end
chip drivers/usb/acpi
register "desc" = ""USB3 Type-C Port C2 (MLB)""
register "type" = "UPC_TYPE_C_USB2_SS_SWITCH"
register "use_custom_pld" = "true"
register "custom_pld" = "{
.visible = true,
.panel = PLD_PANEL_LEFT,
.horizontal_position = PLD_HORIZONTAL_POSITION_LEFT,
.shape = PLD_SHAPE_OVAL,
.group = ACPI_PLD_GROUP(2, 1)}"
device ref tcss_usb3_port3 on end
end
end
end
end
device ref xhci on
chip drivers/usb/acpi
device ref xhci_root_hub on
chip drivers/usb/acpi
register "desc" = ""USB2 Type-C Port C1 (DB)""
register "type" = "UPC_TYPE_C_USB2_SS_SWITCH"
register "use_custom_pld" = "true"
register "custom_pld" = "{
.visible = true,
.panel = PLD_PANEL_RIGHT,
.horizontal_position = PLD_HORIZONTAL_POSITION_LEFT,
.shape = PLD_SHAPE_OVAL,
.group = ACPI_PLD_GROUP(1, 1)}"
device ref usb2_port2 on end
end
chip drivers/usb/acpi
register "desc" = ""USB2 Type-C Port C2 (MLB)""
register "type" = "UPC_TYPE_C_USB2_SS_SWITCH"
register "use_custom_pld" = "true"
register "custom_pld" = "{
.visible = true,
.panel = PLD_PANEL_LEFT,
.horizontal_position = PLD_HORIZONTAL_POSITION_LEFT,
.shape = PLD_SHAPE_OVAL,
.group = ACPI_PLD_GROUP(2, 1)}"
device ref usb2_port3 on end
end
chip drivers/usb/acpi
register "desc" = ""USB2 Camera""
register "type" = "UPC_TYPE_INTERNAL"
device ref usb2_port6 on end
end
chip drivers/usb/acpi
register "desc" = ""USB2 Type-A Port A0 (DB)""
register "type" = "UPC_TYPE_A"
register "use_custom_pld" = "true"
register "custom_pld" = "{
.visible = true,
.panel = PLD_PANEL_RIGHT,
.horizontal_position = PLD_HORIZONTAL_POSITION_LEFT,
.shape = PLD_SHAPE_HORIZONTAL_RECTANGLE,
.group = ACPI_PLD_GROUP(1, 2)}"
device ref usb2_port9 on end
end
chip drivers/usb/acpi
register "desc" = ""USB2 Bluetooth""
register "type" = "UPC_TYPE_INTERNAL"
register "reset_gpio" =
"ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_D4)"
device ref usb2_port10 on end
end
chip drivers/usb/acpi
register "desc" = ""USB3 Type-A Port A0 (DB)""
register "type" = "UPC_TYPE_USB3_A"
register "use_custom_pld" = "true"
register "custom_pld" = "{
.visible = true,
.panel = PLD_PANEL_RIGHT,
.horizontal_position = PLD_HORIZONTAL_POSITION_LEFT,
.shape = PLD_SHAPE_HORIZONTAL_RECTANGLE,
.group = ACPI_PLD_GROUP(1, 2)}"
device ref usb3_port1 on end
end
end
end
end
end
end
|
