summaryrefslogtreecommitdiff
path: root/src/mainboard/asus/p8z77-m_pro/early_init.c
blob: 81eb6f474ca643417219875d18a00841ff1a8316 (plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
/* SPDX-License-Identifier: GPL-2.0-only */
#include <bootblock_common.h>
#include <device/pnp_ops.h>
#include <northbridge/intel/sandybridge/sandybridge.h>
#include <southbridge/intel/bd82x6x/pch.h>

#include <superio/nuvoton/common/nuvoton.h>
#include <superio/nuvoton/nct6779d/nct6779d.h>

#include <option.h>

#include <northbridge/intel/sandybridge/raminit_native.h>
#include <northbridge/intel/sandybridge/raminit.h>
#include <northbridge/intel/sandybridge/pei_data.h>

#define GLOBAL_DEV PNP_DEV(0x2e, 0)
#define SERIAL_DEV PNP_DEV(0x2e, NCT6779D_SP2)

const struct southbridge_usb_port mainboard_usb_ports[] = {
	/* {enable, current, oc_pin} */
	{ 1, 2, 0 }, /* Port 0: USB3 front internal header, top */
	{ 1, 2, 0 }, /* Port 1: USB3 front internal header, bottom */
	{ 1, 2, 1 }, /* Port 2: USB3 rear, ETH top */
	{ 1, 2, 1 }, /* Port 3: USB3 rear, ETH bottom */
	{ 1, 2, 2 }, /* Port 4: USB2 rear, PS2 top */
	{ 1, 2, 2 }, /* Port 5: USB2 rear, PS2 bottom */
	{ 1, 2, 3 }, /* Port 6: USB2 internal header USB78, top */
	{ 1, 2, 3 }, /* Port 7: USB2 internal header USB78, bottom */
	{ 1, 2, 4 }, /* Port 8: USB2 internal header USB910, top */
	{ 1, 2, 4 }, /* Port 9: USB2 internal header USB910, bottom */
	{ 1, 2, 6 }, /* Port 10: USB2 internal header USB1112, top */
	{ 1, 2, 5 }, /* Port 11: USB2 internal header USB1112, bottom */
	{ 0, 2, 5 }, /* Port 12: Unused. Asus proprietary DEBUG_PORT ??? */
	{ 0, 2, 6 }  /* Port 13: Unused. Asus proprietary DEBUG_PORT ??? */
};

void bootblock_mainboard_early_init(void)
{
	/* Setup COM/UART */
	nuvoton_pnp_enter_conf_state(GLOBAL_DEV);

	/* TODO / FIXME: Setup Multifuncion/SIO pins for COM */

	pnp_set_logical_device(SERIAL_DEV);
	nuvoton_pnp_exit_conf_state(GLOBAL_DEV);
	nuvoton_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);
}

void mainboard_get_spd(spd_raw_data *spd, bool id_only)
{
	read_spd(&spd[0], 0x50, id_only);
	read_spd(&spd[1], 0x51, id_only);
	read_spd(&spd[2], 0x52, id_only);
	read_spd(&spd[3], 0x53, id_only);
}

int mainboard_should_reset_usb(int s3resume)
{
	return !s3resume;
}

void mainboard_fill_pei_data(struct pei_data *pei_data)
{
	/*
	 * USB3 mode:
	 * 0 = Disable: work always as USB 2.0(ehci)
	 * 1 = Enable: work always as USB 3.0(xhci)
	 * 2 = Auto: work as USB2.0(ehci) until OS loads USB3 xhci driver
	 * 3 = Smart Auto : same than Auto, but if OS loads USB3 driver
	 *     and reboots, it will keep the USB3.0 speed
	 */
	int usb3_mode = 1;
	get_option(&usb3_mode, "usb3_mode");
	usb3_mode &= 0x3; /* ensure it's 0/1/2/3 only */

	/* Load USB3 pre-OS xHCI driver */
	int usb3_drv = 1;
	get_option(&usb3_drv, "usb3_drv");
	usb3_drv &= 0x1; /* ensure it's 0/1 only */

	/* Use USB3 xHCI streams */
	int usb3_streams = 1;
	get_option(&usb3_streams, "usb3_streams");
	usb3_streams &= 0x1; /* ensure it's 0/1 only */

	struct pei_data pd = {
		.pei_version = PEI_VERSION,
		.mchbar = DEFAULT_MCHBAR,
		.dmibar = DEFAULT_DMIBAR,
		.epbar = DEFAULT_EPBAR,
		.pciexbar = CONFIG_MMCONF_BASE_ADDRESS,
		.smbusbar = CONFIG_FIXED_SMBUS_IO_BASE,
		.wdbbar = 0x4000000,
		.wdbsize = 0x1000,
		.hpet_address = CONFIG_HPET_ADDRESS,
		.rcba = (uintptr_t)DEFAULT_RCBA,
		.pmbase = DEFAULT_PMBASE,
		.gpiobase = DEFAULT_GPIOBASE,
		.thermalbase = 0xfed08000,
		.system_type = 1, /* 0=Mobile, 1=Desktop/Server */
		.tseg_size = CONFIG_SMM_TSEG_SIZE,
		.spd_addresses = { 0xa0, 0xa2, 0xa4, 0xa6 }, /* SMBus mul 2 */
		.ts_addresses = { 0x00, 0x00, 0x00, 0x00 },
		.ec_present = 0, /* Asus 2203 BIOS shows XUECA016, but no EC */
		.gbe_enable = 0, /* Board uses no Intel GbE but a RTL8111F */
		.dimm_channel0_disabled = 0, /* Both DIMM enabled */
		.dimm_channel1_disabled = 0, /* Both DIMM enabled */
		.max_ddr3_freq = 1600, /* 1333=Sandy; 1600=Ivy */
		.usb_port_config = {
			/* {enabled, oc_pin, cable len 0x0080=<8inches/20cm} */
			{ 1, 0, 0x0080 }, /* USB3 front internal header */
			{ 1, 0, 0x0080 }, /* USB3 front internal header */
			{ 1, 1, 0x0080 }, /* USB3 ETH top connector */
			{ 1, 1, 0x0080 }, /* USB3 ETH botton connector */
			{ 1, 2, 0x0080 }, /* USB2 PS2 top connector */
			{ 1, 2, 0x0080 }, /* USB2 PS2 botton connector */
			{ 1, 3, 0x0080 }, /* USB2 internal header (USB78) */
			{ 1, 3, 0x0080 }, /* USB2 internal header (USB78) */
			{ 1, 4, 0x0080 }, /* USB2 internal header (USB910) */
			{ 1, 4, 0x0080 }, /* USB2 internal header (USB910) */
			{ 1, 6, 0x0080 }, /* USB2 internal header (USB1112) */
			{ 1, 5, 0x0080 }, /* USB2 internal header (USB1112) */
			{ 0, 5, 0x0080 }, /* Unused. Asus DEBUG_PORT ??? */
			{ 0, 6, 0x0080 }  /* Unused. Asus DEBUG_PORT ??? */
		},
		.usb3 = {
			/* 0=Disable; 1=Enable (start at USB3 speed)
			 * 2=Auto (start as USB2 speed until OS loads)
			 * 3=Smart Auto (like Auto but keep speed on reboot)
			 */
			usb3_mode,
			/* 4 bit switch mask. 0=not switchable, 1=switchable
			 * Means once it's loaded the OS, it can swap ports
			 * from/to EHCI/xHCI. Z77 has four USB3 ports, so 0xf
			 */
			0xf,
			usb3_drv, /* 1=Load xHCI pre-OS drv */
			/* 0=Don't use xHCI streams for better compatibility
			 * 1=use xHCI streams for better speed
			 */
			usb3_streams
		},
		/* ASUS P8Z77-M PRO manual says 1.35v DIMMs are supported */
		.ddr3lv_support = 1,
		/* PCIe 3.0 support. As we use Ivy Bridge, let's enable it,
		 * but might cause some system instability !
		 */
		.pcie_init = 1,
		/* Command Rate. 0=Auto; 1=1N; 2=2N.
		 * Leave it always at Auto for compatibility & stability
		 */
		.nmode = 0,
		/* DDR refresh rate. 0=Auto based on DRAM's temperature;
		 * 1=Normal rate for speed; 2=Double rate for stability
		 */
		.ddr_refresh_rate_config = 0
	};

	/* copy the data to output PEI */
	*pei_data = pd;
}