1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
|
chip soc/intel/skylake
# Enable Panel as eDP and configure power delays
register "panel_cfg" = "{
.up_delay_ms = 210, // T3
.down_delay_ms = 500, // T10
.cycle_delay_ms = 5000, // T12
.backlight_on_delay_ms = 1, // T7
.backlight_off_delay_ms = 200, // T9
}"
# Enable deep Sx states
register "deep_s3_enable_ac" = "1"
register "deep_s3_enable_dc" = "1"
register "deep_s5_enable_ac" = "1"
register "deep_s5_enable_dc" = "1"
register "deep_sx_config" = "DSX_EN_LAN_WAKE_PIN"
register "eist_enable" = "1"
# GPE configuration
# Note that GPE events called out in ASL code rely on this
# route. i.e. If this route changes then the affected GPE
# offset bits also need to be changed.
register "gpe0_dw0" = "GPP_C"
register "gpe0_dw1" = "GPP_D"
register "gpe0_dw2" = "GPP_E"
# Disable DPTF
register "dptf_enable" = "0"
# FSP Configuration
register "DspEnable" = "0"
register "IoBufferOwnership" = "0"
register "SkipExtGfxScan" = "1"
register "SaGv" = "SaGv_Enabled"
register "PmConfigSlpS3MinAssert" = "2" # 50ms
register "PmConfigSlpS4MinAssert" = "1" # 1s
register "PmConfigSlpSusMinAssert" = "3" # 500ms
register "PmConfigSlpAMinAssert" = "3" # 2s
# PL1 override 25W
# PL2 override 44W
register "power_limits_config" = "{
.tdp_pl1_override = 25,
.tdp_pl2_override = 44,
}"
# Send an extra VR mailbox command for the PS4 exit issue
register "SendVrMbxCmd" = "2"
device domain 0 on
device ref igpu on end
device ref sa_thermal on end
device ref south_xhci on
register "usb2_ports" = "{
[0] = USB2_PORT_MID(OC1), // Type-A Port (left)
[1] = USB2_PORT_MID(OC1), // Type-A Port (left)
[2] = USB2_PORT_FLEX(OC_SKIP), // FPR
[3] = USB2_PORT_FLEX(OC_SKIP), // SD
[4] = USB2_PORT_FLEX(OC_SKIP), // INT
[5] = USB2_PORT_MID(OC1), // Type-A Port (right)
[6] = USB2_PORT_FLEX(OC_SKIP), // Webcam
[7] = USB2_PORT_MID(OC_SKIP), // mPCIe / WiFi Port
[8] = USB2_PORT_MID(OC_SKIP), // mSATA / WWAN Port
}"
register "usb3_ports" = "{
[0] = USB3_PORT_DEFAULT(OC1), // Type-A Port (left)
[1] = USB3_PORT_DEFAULT(OC1), // Type-A Port (left)
}"
end
device ref thermal on end
device ref heci1 on end
device ref sata on
register "SataSalpSupport" = "1"
# The X210 has 3 SATA ports: a full SATA port, mSATA, and SATA over M.2
register "SataPortsEnable" = "{
[0] = 1,
[1] = 1,
[2] = 1,
}"
register "SataPortsDevSlp" = "{
[0] = 1,
[1] = 1,
[2] = 1,
}"
end
device ref pcie_rp3 on
# Ethernet controller
register "PcieRpEnable[2]" = "1"
register "PcieRpClkReqSupport[2]" = "1"
register "PcieRpClkReqNumber[2]" = "0"
register "PcieRpClkSrcNumber[2]" = "0"
register "PcieRpAdvancedErrorReporting[2]" = "1"
register "PcieRpLtrEnable[2]" = "1"
end
device ref pcie_rp4 on
# Wireless controller
register "PcieRpEnable[3]" = "1"
register "PcieRpClkReqSupport[3]" = "1"
register "PcieRpClkReqNumber[3]" = "1"
register "PcieRpClkSrcNumber[3]" = "1"
register "PcieRpAdvancedErrorReporting[3]" = "1"
register "PcieRpLtrEnable[3]" = "1"
end
device ref pcie_rp9 on
# NVMe controller
register "PcieRpEnable[8]" = "1"
register "PcieRpClkReqSupport[8]" = "1"
register "PcieRpClkReqNumber[8]" = "4"
register "PcieRpClkSrcNumber[8]" = "4"
register "PcieRpAdvancedErrorReporting[8]" = "1"
register "PcieRpLtrEnable[8]" = "1"
end
device ref lpc_espi on
register "serirq_mode" = "SERIRQ_CONTINUOUS"
register "gen1_dec" = "0x000c0681"
register "gen2_dec" = "0x000c1641"
chip ec/51nb/npce985la0dx
device pnp 0c09.0 on end
device pnp 4e.5 on end
device pnp 4e.6 on end
device pnp 4e.11 on end
end
end
device ref pmc on end
device ref hda on end
device ref smbus on end
end
end
|
