blob: d4ab5307206d74b88d413cf46834a28ad2020b2a (
plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
|
chip soc/intel/skylake
# Enable Panel as eDP and configure power delays
register "gpu_pp_up_delay_ms" = "210" # T3
register "gpu_pp_down_delay_ms" = "500" # T10
register "gpu_pp_cycle_delay_ms" = "5000" # T12
register "gpu_pp_backlight_on_delay_ms" = "1" # T7
register "gpu_pp_backlight_off_delay_ms" = "200" # T9
# Enable deep Sx states
register "deep_s3_enable_ac" = "1"
register "deep_s3_enable_dc" = "1"
register "deep_s5_enable_ac" = "1"
register "deep_s5_enable_dc" = "1"
register "deep_sx_config" = "DSX_EN_LAN_WAKE_PIN"
register "eist_enable" = "1"
# GPE configuration
# Note that GPE events called out in ASL code rely on this
# route. i.e. If this route changes then the affected GPE
# offset bits also need to be changed.
register "gpe0_dw0" = "GPP_C"
register "gpe0_dw1" = "GPP_D"
register "gpe0_dw2" = "GPP_E"
register "gen1_dec" = "0x000c0081"
register "gen2_dec" = "0x000c0681"
register "gen3_dec" = "0x000c1641"
# Enable "Intel Speed Shift Technology"
register "speed_shift_enable" = "1"
# Disable DPTF
register "dptf_enable" = "0"
# FSP Configuration
register "ProbelessTrace" = "0"
register "SataSalpSupport" = "1"
register "SataMode" = "0"
# The X210 has 3 SATA ports: a full SATA port, mSATA, and SATA over M.2
register "SataPortsEnable[0]" = "1"
register "SataPortsEnable[1]" = "1"
register "SataPortsEnable[2]" = "1"
register "SataPortsDevSlp[0]" = "1"
register "SataPortsDevSlp[1]" = "1"
register "SataPortsDevSlp[2]" = "1"
register "DspEnable" = "0"
register "IoBufferOwnership" = "0"
register "SsicPortEnable" = "0"
register "Cio2Enable" = "0"
register "ScsEmmcHs400Enabled" = "0"
register "ScsSdCardEnabled" = "0"
register "PttSwitch" = "0"
register "SkipExtGfxScan" = "1"
register "Device4Enable" = "1"
register "HeciEnabled" = "1"
register "SaGv" = "SaGv_Enabled"
register "PmConfigSlpS3MinAssert" = "2" # 50ms
register "PmConfigSlpS4MinAssert" = "1" # 1s
register "PmConfigSlpSusMinAssert" = "3" # 500ms
register "PmConfigSlpAMinAssert" = "3" # 2s
register "PmTimerDisabled" = "0"
register "serirq_mode" = "SERIRQ_CONTINUOUS"
register "PmConfigPciClockRun" = "1"
# Enable Root Ports 3, 4 and 9
register "PcieRpEnable[2]" = "1" # Ethernet controller
register "PcieRpClkReqSupport[2]" = "1"
register "PcieRpClkReqNumber[2]" = "0"
register "PcieRpClkSrcNumber[2]" = "0"
register "PcieRpAdvancedErrorReporting[2]" = "1"
register "PcieRpLtrEnable[2]" = "1"
register "PcieRpEnable[3]" = "1" # Wireless controller
register "PcieRpClkReqSupport[3]" = "1"
register "PcieRpClkReqNumber[3]" = "1"
register "PcieRpClkSrcNumber[3]" = "1"
register "PcieRpAdvancedErrorReporting[3]" = "1"
register "PcieRpLtrEnable[3]" = "1"
register "PcieRpEnable[8]" = "1" # NVMe controller
register "PcieRpClkReqSupport[8]" = "1"
register "PcieRpClkReqNumber[8]" = "4"
register "PcieRpClkSrcNumber[8]" = "4"
register "PcieRpAdvancedErrorReporting[8]" = "1"
register "PcieRpLtrEnable[8]" = "1"
register "usb2_ports[0]" = "USB2_PORT_MID(OC1)" # Type-A Port (left)
register "usb2_ports[1]" = "USB2_PORT_MID(OC1)" # Type-A Port (left)
register "usb2_ports[2]" = "USB2_PORT_FLEX(OC_SKIP)" # FPR
register "usb2_ports[3]" = "USB2_PORT_FLEX(OC_SKIP)" # SD
register "usb2_ports[4]" = "USB2_PORT_FLEX(OC_SKIP)" # INT
register "usb2_ports[5]" = "USB2_PORT_MID(OC1)" # Type-A Port (right)
register "usb2_ports[6]" = "USB2_PORT_FLEX(OC_SKIP)" # Webcam
register "usb2_ports[7]" = "USB2_PORT_MID(OC_SKIP)" # mPCIe / WiFi Port
register "usb2_ports[8]" = "USB2_PORT_MID(OC_SKIP)" # mSATA / WWAN Port
register "usb3_ports[0]" = "USB3_PORT_DEFAULT(OC1)" # Type-A Port (left)
register "usb3_ports[1]" = "USB3_PORT_DEFAULT(OC1)" # Type-A Port (left)
# PL1 override 25W
# PL2 override 44W
register "power_limits_config" = "{
.tdp_pl1_override = 25,
.tdp_pl2_override = 44,
}"
# Send an extra VR mailbox command for the PS4 exit issue
register "SendVrMbxCmd" = "2"
# Lock Down
register "common_soc_config" = "{
.chipset_lockdown = CHIPSET_LOCKDOWN_COREBOOT,
}"
device cpu_cluster 0 on
device lapic 0 on end
end
device domain 0 on
device pci 00.0 on end # Host Bridge
device pci 02.0 on end # Integrated Graphics Device
device pci 14.0 on end # USB xHCI
device pci 14.1 off end # USB xDCI (OTG)
device pci 14.2 on end # Thermal Subsystem
device pci 16.0 on end # Management Engine Interface 1
device pci 16.1 off end # Management Engine Interface 2
device pci 16.2 off end # Management Engine IDE-R
device pci 16.3 off end # Management Engine KT Redirection
device pci 16.4 off end # Management Engine Interface 3
device pci 17.0 on end # SATA
device pci 1c.0 off end # PCI Express Port 1
device pci 1c.1 off end # PCI Express Port 2
device pci 1c.2 on end # PCI Express Port 3
device pci 1c.3 on end # PCI Express Port 4
device pci 1c.4 off end # PCI Express Port 5
device pci 1c.5 off end # PCI Express Port 6
device pci 1c.6 off end # PCI Express Port 7
device pci 1c.7 off end # PCI Express Port 8
device pci 1d.0 on end # PCI Express Port 9
device pci 1d.1 off end # PCI Express Port 10
device pci 1d.2 off end # PCI Express Port 11
device pci 1d.3 off end # PCI Express Port 12
device pci 1f.0 on
chip ec/51nb/npce985la0dx
device pnp 0c09.0 on end
device pnp 4e.5 on end
device pnp 4e.6 on end
device pnp 4e.11 on end
end
end # LPC Interface
device pci 1f.1 off end # P2SB
device pci 1f.2 on end # Power Management Controller
device pci 1f.3 on end # Intel HDA
device pci 1f.4 on end # SMBus
device pci 1f.5 off end # PCH SPI
device pci 1f.6 off end # GbE
end
end
|
