1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
|
/* cpuRegInit */
void cpuRegInit (void)
{
int msrnum;
msr_t msr;
/* The following is only for diagnostics mode; do not use for OLPC */
if (0) {
/* Set Diagnostic Mode */
msrnum = CPU_GLD_MSR_DIAG;
msr.hi = 0;
msr.lo = DIAG_SEL1_SET | DIAG_SET0_SET;
wrmsr(msrnum, msr);
/* Set up GLCP to grab BTM data. */
msrnum = GLCP_DBGOUT; /* GLCP_DBGOUT MSR */
msr.hi = 0x0;
msr.lo = 0x08; /* reset value (SCOPE_SEL = 0) causes FIFO toshift out, */
wrmsr(msrnum, msr); /* exchange it to anything else to prevent this */
/* Turn off debug clock */
msrnum = GLCP_DBGCLKCTL; /* DBG_CLK_CTL */
msr.lo = 0x00; /* No clock */
msr.hi = 0x00;
wrmsr(msrnum, msr);
/* Set debug clock to CPU */
msrnum = GLCP_DBGCLKCTL; /* DBG_CLK_CTL */
msr.lo = 0x01; /* CPU CLOCK */
msr.hi = 0x00;
wrmsr(msrnum, msr);
/* Set fifo ctl to BTM bits wide */
msrnum = GLCP_FIFOCTL; /* FIFO_CTL */
msr.lo = 0x003880000; /* Bit [25:24] are size (11=BTM, 10 = 64 bit, 01= 32 bit, 00 = 16bit) */
wrmsr(msrnum, msr); /* Bit [23:21] are position (100 = CPU downto0) */
/* Bit [19] sets it up in slow data mode. */
/* enable fifo loading - BTM sizing will constrain */
/* only valid BTM packets to load - this action should always be on */
msrnum = 0x04C00006F; /* GLCP ACTION7 - load fifo */
msr.lo = 0x00000F000; /* Any nibble all 1's will always trigger */
msr.hi = 0x000000000;
wrmsr(msrnum, msr);
/* start storing diag data in the fifo */
msrnum = 0x04C00005F; /* DIAG CTL */
msr.lo = 0x080000000; /* enable actions */
msr.hi = 0x000000000;
wrmsr(msrnum, msr);
/* Set up delay on data lines, so that the hold time */
/* is 1 ns. */
msrnum = GLCP_PROCSTAT; /* GLCP IO DELAY CONTROLS */
msr.lo = 0x082b5ad68;
msr.hi = 0x080ad6b57; /* RGB delay = 0x07 */
wrmsr(msrnum, msr);
/* Set up DF to output diag information on DF pins. */
msrnum = DF_GLD_MSR_MASTER_CONF;
msr.lo = 0x0220;
msr.hi = 0;
wrmsr(msrnum, msr);
msrnum = GLCP_DBGOUT; /* GLCP_DBGOUT MSR */
msr.hi = 0x0;
msr.lo = 0x0; /* reset value (SCOPE_SEL = 0) causes FIFO to shift out, */
wrmsr(msrnum, msr);
/* end of code for BTM */
}
/* Enable Suspend on Halt */
msrnum = CPU_XC_CONFIG;
msr = rdmsr(msrnum);
msr.lo |= XC_CONFIG_SUSP_ON_HLT;
wrmsr(msrnum, msr);
/* ENable SUSP and allow TSC to run in Suspend */
/* to keep speed detection happy */
msrnum = CPU_BC_CONF_0;
msr = rdmsr(msrnum);
msr.lo |= TSC_SUSP_SET | SUSP_EN_SET;
wrmsr(msrnum, msr);
/* Setup throttling to proper mode if it is ever enabled. */
msrnum = GLCP_TH_OD;
msr.hi = 0x000000000;
msr.lo = 0x00000603C;
wrmsr(msrnum, msr);
/* Only do this if we are building for 5535 */
/* FooGlue Setup */
#if 1
/* Enable CIS mode B in FooGlue */
msrnum = MSR_FG + 0x10;
msr = rdmsr(msrnum);
msr.lo &= ~3;
msr.lo |= 2; /* ModeB */
wrmsr(msrnum, msr);
#endif
/* Disable DOT PLL. Graphics init will enable it if needed. */
msrnum = GLCP_DOTPLL;
msr = rdmsr(msrnum);
msr.lo |= DOTPPL_LOWER_PD_SET;
wrmsr(msrnum, msr);
/* Enable RSDC */
msrnum = CPU_AC_SMM_CTL;
msr = rdmsr(msrnum);
msr.lo |= 0x08;
wrmsr(msrnum, msr);
/* Enable BTB */
/* I hate to put this check here but it doesn't really work in cpubug.asm */
msrnum = GLCP_CHIP_REVID;
msr = rdmsr(msrnum);
if (msr.lo >= CPU_REV_2_1){
msrnum = CPU_PF_BTB_CONF;
msr = rdmsr(msrnum);
msr.lo |= BTB_ENABLE_SET | RETURN_STACK_ENABLE_SET;
wrmsr(msrnum, msr);
}
/* FPU impercise exceptions bit */
{
msrnum = CPU_FPU_MSR_MODE;
msr = rdmsr(msrnum);
msr.lo |= FPU_IE_SET;
wrmsr(msrnum, msr);
}
}
|
