1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
277
278
279
280
281
282
283
284
285
286
287
288
289
290
291
292
293
294
295
296
297
298
299
300
301
302
303
304
305
306
307
308
309
310
311
312
313
314
315
316
317
318
319
320
321
322
323
324
325
326
327
328
329
330
331
332
333
334
335
336
337
338
339
340
341
342
343
344
345
346
347
348
349
350
351
352
353
354
355
356
357
358
359
360
361
362
363
364
365
366
367
368
369
370
371
372
373
374
375
376
377
378
379
380
381
382
383
384
385
386
387
388
389
390
391
392
393
394
395
396
397
398
399
400
401
402
403
404
405
406
407
408
409
410
411
412
413
414
415
416
417
418
419
420
421
422
423
424
425
426
427
428
429
430
431
432
433
434
435
436
437
438
439
440
441
442
443
444
445
446
447
448
449
450
451
452
453
454
455
456
457
458
459
460
461
462
463
464
465
466
467
468
469
470
471
472
473
474
475
476
477
478
479
480
481
482
483
484
485
486
487
488
489
490
491
492
493
494
495
496
497
498
499
500
501
502
503
504
505
506
507
508
509
510
511
512
513
514
515
516
517
518
519
520
521
522
523
524
525
526
527
528
529
530
531
532
533
534
535
536
537
538
539
540
541
542
543
544
545
546
547
548
549
550
551
552
553
554
555
556
557
558
559
560
561
562
563
564
565
566
567
568
569
570
571
572
573
574
575
576
577
578
579
580
581
582
583
584
585
586
587
588
589
590
591
592
593
594
595
596
597
598
599
600
601
602
603
604
605
606
607
608
609
610
611
612
613
614
615
616
617
618
619
620
621
622
623
624
625
626
627
628
629
630
631
632
633
634
635
636
637
638
639
640
641
642
643
644
645
646
647
648
649
650
651
652
653
654
655
656
657
658
659
660
661
662
663
664
665
666
667
668
669
670
671
672
673
674
675
676
677
678
679
680
681
682
683
684
685
686
687
688
689
690
691
692
693
694
695
696
697
698
699
700
701
702
703
704
705
706
707
708
709
710
711
712
713
714
715
716
717
718
719
720
721
722
723
724
725
726
727
728
729
730
731
732
733
734
735
736
737
738
739
740
741
742
743
744
745
746
747
748
749
750
751
752
753
754
755
756
757
758
759
760
761
762
763
764
765
766
767
768
769
770
771
772
773
774
775
776
777
778
779
780
781
782
783
784
785
786
787
788
789
790
791
792
793
794
795
796
797
798
799
800
801
802
803
804
805
806
807
808
809
810
811
812
813
814
815
816
817
818
819
820
821
822
823
824
825
826
827
828
829
830
831
832
833
834
835
836
837
838
839
840
841
842
843
844
845
846
847
848
849
850
851
852
853
854
855
856
857
858
859
860
861
862
863
864
865
866
867
868
869
870
871
872
873
874
875
876
877
878
879
880
881
882
883
884
885
886
887
888
889
890
891
892
893
894
895
896
897
898
899
900
901
902
903
904
905
906
907
908
909
910
911
912
913
914
915
916
917
918
919
920
921
922
923
924
925
926
927
928
929
930
931
932
933
934
935
936
937
938
939
940
941
942
943
944
945
946
947
948
949
950
951
952
953
954
955
956
957
958
959
960
961
962
963
964
965
966
967
968
969
970
971
972
973
974
975
976
977
978
979
980
981
982
983
984
985
986
987
988
989
990
991
992
993
994
995
996
997
998
999
1000
1001
1002
1003
1004
1005
1006
1007
1008
1009
1010
1011
1012
1013
1014
1015
1016
1017
1018
1019
1020
1021
1022
1023
1024
1025
1026
1027
1028
1029
1030
1031
1032
1033
1034
1035
1036
1037
1038
1039
1040
1041
1042
1043
1044
1045
1046
1047
1048
1049
1050
1051
1052
1053
1054
1055
1056
1057
1058
1059
1060
1061
1062
1063
1064
1065
1066
1067
1068
1069
1070
1071
1072
1073
1074
1075
1076
1077
1078
1079
1080
1081
1082
1083
1084
1085
1086
1087
1088
1089
1090
1091
1092
1093
1094
1095
1096
1097
1098
1099
1100
1101
1102
1103
1104
1105
1106
1107
1108
1109
1110
1111
1112
1113
1114
1115
1116
1117
1118
1119
1120
1121
1122
1123
1124
1125
1126
1127
1128
1129
1130
1131
1132
1133
1134
1135
1136
1137
1138
1139
1140
1141
1142
1143
1144
1145
1146
1147
1148
1149
1150
1151
1152
1153
1154
1155
1156
1157
1158
1159
1160
1161
1162
1163
1164
1165
1166
1167
1168
1169
1170
1171
1172
1173
1174
1175
1176
1177
1178
1179
1180
1181
1182
1183
1184
1185
1186
1187
1188
1189
1190
1191
1192
1193
1194
1195
1196
1197
1198
1199
1200
1201
1202
1203
1204
1205
1206
1207
1208
1209
1210
1211
1212
1213
1214
1215
1216
1217
1218
1219
1220
1221
1222
1223
1224
1225
1226
1227
1228
1229
1230
1231
1232
1233
1234
1235
1236
1237
1238
1239
1240
1241
1242
1243
1244
1245
1246
1247
1248
1249
1250
1251
1252
1253
1254
1255
1256
1257
1258
1259
1260
1261
1262
1263
1264
1265
1266
1267
1268
1269
1270
1271
1272
1273
1274
1275
1276
1277
1278
1279
1280
1281
1282
1283
1284
1285
1286
1287
1288
1289
1290
1291
1292
1293
1294
1295
1296
1297
1298
1299
1300
1301
1302
1303
1304
1305
1306
1307
1308
1309
1310
1311
1312
1313
1314
1315
1316
1317
1318
1319
1320
1321
1322
1323
1324
1325
1326
1327
1328
1329
1330
1331
1332
1333
1334
1335
1336
1337
1338
1339
1340
1341
1342
1343
1344
1345
1346
1347
1348
1349
1350
1351
1352
1353
1354
1355
1356
1357
1358
1359
1360
1361
1362
1363
1364
1365
1366
1367
1368
1369
1370
1371
1372
1373
1374
1375
1376
1377
1378
1379
1380
1381
1382
1383
1384
1385
1386
1387
1388
1389
1390
1391
1392
1393
1394
1395
1396
1397
1398
1399
1400
1401
1402
1403
1404
1405
1406
1407
1408
1409
1410
1411
1412
1413
1414
1415
1416
1417
1418
1419
1420
1421
1422
1423
1424
1425
1426
1427
1428
1429
1430
1431
1432
1433
1434
1435
1436
1437
1438
1439
1440
1441
1442
1443
1444
1445
1446
1447
1448
1449
1450
1451
1452
1453
1454
1455
1456
1457
1458
1459
1460
1461
1462
1463
1464
1465
1466
1467
1468
1469
1470
1471
1472
1473
1474
1475
1476
1477
1478
1479
1480
1481
1482
1483
1484
1485
1486
1487
1488
1489
1490
1491
1492
1493
1494
1495
1496
1497
1498
1499
1500
1501
1502
1503
1504
1505
1506
1507
1508
1509
1510
1511
1512
1513
1514
1515
1516
1517
1518
1519
1520
1521
1522
1523
1524
1525
1526
1527
1528
1529
1530
1531
1532
1533
1534
1535
1536
1537
1538
1539
1540
1541
1542
1543
1544
1545
1546
1547
1548
1549
1550
1551
1552
1553
1554
1555
1556
1557
1558
1559
1560
1561
1562
1563
1564
1565
1566
1567
1568
1569
1570
1571
1572
1573
1574
1575
1576
|
%
% This document is released under the GPL
% Initially written by Stefan Reinauer, <stepan@openbios.org>
%
\documentclass[titlepage,12pt]{article}
\usepackage{a4}
\usepackage{graphicx}
\usepackage{url}
\usepackage[pdftex]{hyperref}
% \usepackage{makeidx}
% \makeindex
\hypersetup{
urlbordercolor={1 1 1},
menubordercolor={1 1 1},
linkbordercolor={1 1 1},
colorlinks=false,
% pdfpagemode=None, % PDF-Viewer starts without TOC
% pdfstartview=FitH,
pdftitle={LinuxBIOS on AMD64},
pdfauthor={Stefan Reinauer},
pdfsubject={LinuxBIOS configuration and build process},
pdfkeywords={LinuxBIOS, Opteron, AMD64, Athlon64, Build}
}
% \newcommand{\sh}[1]{\begin{verbatim}\texttt{#1}\end{verbatim}}
% \newcommand{\prog}[1]{\textit{#1}}
\setlength{\parindent}{0pt}
\title{LinuxBIOS on AMD64}
\author{Stefan Reinauer $<$stepan@openbios.org$>$}
\date{June 2nd, 2004}
\begin{document}
\maketitle
\thispagestyle{empty}
\tableofcontents
\newpage
%
% 1 Abstract
%
\section{Abstract}
This document targets porting LinuxBIOS to new mainboards and creating
custom firmware images using LinuxBIOS. It describes how to build
LinuxBIOS images for the AMD64 platform, including hypertransport
configuration and pertinent utilities. If you are missing information or
find errors in the following descriptions, contact
\href{mailto:stepan@openbios.org}{\textit{Stefan Reinauer $<$stepan@openbios.org$>$}}
%
% 2 Changes
%
\section{Changes}
\begin{itemize}
\item 2004/06/02 url and language fixes from Ken Fuchs $<$kfuchs@winternet.com$>$
\item 2004/02/10 acpi and option rom updates
\item 2003/11/18 initial release
\end{itemize}
%
% 3 What is LinuxBIOS
%
\section{What is LinuxBIOS?}
LinuxBIOS aims to replace the normal BIOS found on PCs, Alphas, and
other machines with a Linux kernel that can boot Linux from a cold
start. The startup code of an average LinuxBIOS port is about 500 lines
of assembly and 5000 lines of C. It executes 16 instructions to get into
32bit mode and then performs DRAM and other hardware initializations
required before Linux can take over.
The projects primary motivation initially was maintenance of large
clusters. Not surprisingly interest and contributions have come from
people with varying backgrounds. Nowadays a large and growing number of
Systems can be booted with LinuxBIOS, including embedded systems,
Desktop PCs and Servers.
%
% 4 Build Requirements
%
\section{Build Requirements}
To build LinuxBIOS for AMD64 from the sources you need a recent Linux
system for x86 or AMD64. SUSE Linux 8.2 or 9.0 are known to work fine.
The following toolchain is recommended:
\begin{itemize}
\item GCC 3.3.1
\item binutils 2.14.90.0.5
\item Python 2.3
\item CVS 1.11.6
\end{itemize}
\textbf{NOTE:} Later versions should also work. Prior versions might lead to problems.
\newpage
%
% 5 Getting the Sources
%
\section{Getting the Sources}
The latest LinuxBIOS sources are available via CVS. The CVS repository
is maintained at SourceForge.net (the project name is \emph{FreeBIOS}).
First you should create a directory for your LinuxBIOS trees:
{ \small
\begin{verbatim}
$ mkdir linuxbios
$ cd linuxbios
\end{verbatim}
}
You can get the entire source tree via CVS:
{ \small
\begin{verbatim}
$ cvs -d:pserver:anonymous@cvs.sourceforge.net:/cvsroot/freebios login
\end{verbatim}
}
Hit return when you are asked for a password. Then checkout (or update)
the freebios source tree as follows:
{ \small
\begin{verbatim}
$ cvs -z3 -d:pserver:anonymous@cvs.sourceforge.net:/cvsroot/freebios co freebios2
\end{verbatim}
}
Once the source tree is checked out, it can be updated with:
{ \small
\begin{verbatim}
% cvs update �Pd
\end{verbatim}
}
Due to recent problems with SourceForge's CVS infrastructure we set up a
snapshot site that keeps hourly source trees of the last four days. It
is available at \url{http://snapshots.linuxbios.org/}.
Due to major structural enhancements to \hbox{LinuxBIOS}, AMD64 support
is only available in the \texttt{freebios2} tree. This tree reflects (as
of November 2003) LinuxBIOS version 1.1.5 and will lead to LinuxBIOS 2.0
when finished. Most x86 hardware is currently only supported by the
LinuxBIOS 1.0 tree.
%
% 6 LinuxBIOS configuration overview
%
\section{LinuxBIOS configuration overview}
To support a large variety of existing hardware LinuxBIOS allows for a
lot of configuration options that can be tweaked in several ways:
\begin{itemize}
\item
Firmware image specific configuration options can be set in the image
configuration file which is usually found in
\texttt{freebios2/targets/$<$vendor$>$/$<$mainboard$>$/}. Such
options are the default amount of output verbosity during bootup, image
size, use of fallback mechanisms, firmware image size and payloads
(Linux Kernel, Bootloader...) The default configuration file name is
\texttt{Config.lb}, but LinuxBIOS allows multiple configurations to
reside in that directory.
\item Mainboard specific configuration options can be set in the
mainboard configuration file placed in
\texttt{freebios2/src/mainboard/$<$vendor$>$/$<$mainboard$>$}. The
mainboard configuration file is always called \texttt{Config.lb}. It
contains information on the onboard components of the mainboard like
CPU type, northbridge, southbridge, hypertransport configuration and
SuperIO configuration. This configuration file also allows to include
addon code to hook into the LinuxBIOS initialization mechanism at
basically any point.
\end{itemize}
This document describes different approaches of changing and configuring the
LinuxBIOS source tree when building for AMD64.
%
% 7 Building LinuxBIOS
%
\section{Building LinuxBIOS}
One of the design goals for building LinuxBIOS was to keep object files
out of the source tree in a separate place. This is mandatory for
building parallel LinuxBIOS images for several distinct mainboards
and/or platforms. Therefore building LinuxBIOS consists of two steps:
\begin{itemize}
\item
creating a build tree which holds all files automatically created by the
configuration utility and the object files
\item
compiling the LinuxBIOS code and creating a flashable firmware image.
\end{itemize}
The first of these two steps is accomplished by the \texttt{buildtarget}
script found in \texttt{freebios2/targets/}. To build LinuxBIOS for
instance for the AMD Solo Athlon64 mainboard enter:
\begin{verbatim}
% cd freebios2/targets
% ./buildtarget amd/solo
\end{verbatim}
This will create a directory containing a Makefile and other software
components needed for this build. The directory name is defined in the
firmware image specific configuration file. In the case of AMD's Solo
mainboard the default directory resides in
\texttt{freebios2/targets/amd/solo/solo}. To build the LinuxBIOS image, do
\begin{verbatim}
% cd amd/solo/solo
% make
\end{verbatim}
The LinuxBIOS image filename is specified in the firmware image specific
configuration file. The default filename for AMD's Solo mainboard is
\texttt{solo.rom}.
%
% 8 Programming LinuxBIOS to flash memory
%
\section{Programming LinuxBIOS to flash memory}
The image resulting from a LinuxBIOS build can be directly programmed to
a flash device, either using a hardware flash programmer or by using the
Linux flash driver devbios or mtd. This document assumes that you use a
hardware flash programmer. If you are interested in doing in-system
software flash programming, find detailed information:
\begin{itemize}
\item \url{http://www.openbios.org/development/devbios.html} (/dev/bios)
\item \url{http://www.linux-mtd.infradead.org/} (Memory Technology Device Subsystem MTD)
\end{itemize}
\newpage
%
% 9 LinuxBIOS configuration
%
\section{LinuxBIOS configuration}
The following chapters will cope with configuring LinuxBIOS. All
configuration files share some basic rules
\begin{itemize}
\item
The default configuration file name in LinuxBIOS is \texttt{Config.lb}.
\item
All variables used in a configuration file have to be declared in this
file with \texttt{uses VARNAME} before usage.
\item
Comments can be added on a new line by using the comment identifier
\texttt{\#} at the beginning of the line.
\item
LinuxBIOS distinguishes between statements and options. Statements cause
the LinuxBIOS configuration mechanism to act, whereas options set
variables that are used by the build scripts or source code.
\item
Default configuration values can be set in the mainboard configuration
files (keyword default)
\item
Option overrides to the default configuration can only be specified in
the build target configuration file
\texttt{freebios2/targets/$<$vendor$>$/$<$mainboard$>$/Config.lb}
(keyword option)
\end{itemize}
\subsection{Common Configuration Statements}
\begin{itemize}
\item \begin{verbatim}uses\end{verbatim}
All local configuration variables have to be declared before they can be
used. Example:
\begin{verbatim}
uses ROM_IMAGE_SIZE
\end{verbatim}
\textbf{NOTE:} Only configuration variables known to the configuration
system can be used in configuration files. LinuxBIOS checks
\texttt{freebios2/src/config/Options.lb} to see whether a configuration
variable is known.
\item \begin{verbatim}default\end{verbatim}
The \texttt{default} statement is used to set a configuration variable
with an overridable default value. It is commonly used in mainboard
configuration files.
Example:
\begin{verbatim}
default ROM_IMAGE_SIZE=0x10000
\end{verbatim}
It is also possible to assign the value of one configuration variable to
another one, i.e.:
\begin{verbatim}
default FALLBACK_SIZE=ROM_SIZE
\end{verbatim}
Also, simple expressions are allowed:
\begin{verbatim}
default FALLBACK_SIZE=(ROM_SIZE - NORMAL_SIZE)
\end{verbatim}
If an option contains a string, this string has to be protected with
quotation marks:
\begin{verbatim}
default CC="gcc �m32"
\end{verbatim}
\item \begin{verbatim}option\end{verbatim}
The \texttt{option} statement basically behaves identically to the
\texttt{default} statement. But unlike default it can only be used in
build target configuration files
(\texttt{freebios2/targets/$<$vendor$>$/$<$mainboard$>$}). The option
statement allows either to set new options or to override default values
set with the default statement in a mainboard configuration file.
Syntax and application are the same as with default.
\end{itemize}
\subsection{Firmware image specific configuration}
LinuxBIOS allows to create different firmware images for the same
hardware. Such images can differ in the amount of output they produce,
the payload, the number of subimages they consist of etc.
The firmware image specific configuration file can be found in \\
\texttt{freebios2/targets/$<$vendor$>$/<mainboard$>$}.
\subsubsection{Firmware image specific keywords}
In addition to the above described keywords the following statements are
available in firmware image specific configuration files:
\begin{itemize}
\item \begin{verbatim}romimage\end{verbatim}
The \texttt{romimage} definition describes a single rom build within the
final LinuxBIOS image. Normally there are two romimage definitions per
LinuxBIOS build: \texttt{normal} and \texttt{fallback}.
Each \texttt{romimage} section needs to specify a mainboard directory and a
payload. The mainboard directory contains the mainboard specific
configuration file and source code. It is specified relatively to
\texttt{freebios2/src/mainboard}. The payload definition is an absolute
path to a static elf binary (i.e Linux kernel or etherboot)
\begin{verbatim}
romimage "normal"
option USE_FALLBACK_IMAGE=0
option ROM_IMAGE_SIZE=0x10000
option LINUXBIOS_EXTRA_VERSION=".0Normal"
mainboard amd/solo
payload /suse/stepan/tg3ide_
disk.zelf
end
\end{verbatim}
\item \begin{verbatim}buildrom\end{verbatim}
The \texttt{buildrom} statement is used to determine which of the
LinuxBIOS image builds (created using \texttt{romimage}) are packed
together to the final LinuxBIOS image. It also specifies the order of
the images and the final image size:
\begin{verbatim}
buildrom ./solo.rom ROM_SIZE "normal" "fallback"
\end{verbatim}
\end{itemize}
\subsubsection{Firmware image configuration options}
In addition to the definitions described above there are a number of
commonly used options. Configuration options set in the firmware image
specific configuration file can override default selections from the
Mainboard specific configuration. See above examples about
option on how to set them.
\begin{itemize}
\item \begin{verbatim}CC\end{verbatim}
Target C Compiler. Default is \texttt{\$(CROSS\_COMPILE)gcc}. Set to
\texttt{gcc �m32} for compiling AMD64 LinuxBIOS images on an AMD64
machine.
\item \begin{verbatim}CONFIG_CHIP_CONFIGURE \end{verbatim}
Use new \textit{chip\_configure} method for configuring (nonpci)
devices. Set to \texttt{1} for all AMD64 mainboards.
\item \begin{verbatim}MAXIMUM_CONSOLE_LOGLEVEL\end{verbatim}
Errors or log messages up to this level can be printed. Default is
\texttt{8}, minimum is \texttt{0}, maximum is \texttt{10}.
\item \begin{verbatim}DEFAULT_CONSOLE_LOGLEVEL\end{verbatim}
Console will log at this level unless changed. Default is \texttt{7},
minimum is \texttt{0}, maximum is \texttt{10}.
\item \begin{verbatim}CONFIG_CONSOLE_SERIAL8250\end{verbatim}
Log messages to 8250 uart based serial console. Default is \texttt{0}
(don't log to serial console). This value should be set to \texttt{1}
for all AMD64 builds.
\item \begin{verbatim}ROM_SIZE\end{verbatim}
Size of final ROM image. This option has no default value.
\item \begin{verbatim}FALLBACK_SIZE\end{verbatim}
Fallback image size. Defaults to \texttt{65536} bytes. \textbf{NOTE:}
This does not include the fallback payload.
\item \begin{verbatim}HAVE_OPTION_TABLE\end{verbatim}
Export CMOS option table. Default is \texttt{0}. Set to \texttt{1} if
your mainboard has CMOS memory and you want to use it to store
LinuxBIOS parameters (Loglevel, serial line speed, ...)
\item \begin{verbatim}CONFIG_ROM_STREAM\end{verbatim}
Boot image is located in ROM (as opposed to \texttt{CONFIG\_IDE\_STREAM}, which
will boot from an IDE disk)
\item \begin{verbatim}HAVE_FALLBACK_BOOT\end{verbatim}
Set to \texttt{1} if fallback booting is required. Defaults to
\texttt{0}.
\end{itemize}
The following options should be used within a romimage section:
\begin{itemize}
\item \begin{verbatim}USE_FALLBACK_IMAGE\end{verbatim}
Set to \texttt{1} to build a fallback image. Defaults to \texttt{0}
\item \begin{verbatim}ROM_IMAGE_SIZE\end{verbatim}
Default image size. Defaults to \texttt{65535} bytes.
\item \begin{verbatim}LINUXBIOS_EXTRA_VERSION\end{verbatim}
LinuxBIOS extra version. This option has an empty string as default. Set
to any string to add an extra version string to your LinuxBIOS build.
\end{itemize}
\newpage
\subsection{Mainboard specific configuration}
Mainboard specific configuration files describe the onboard
mainboard components, i.e. bridges, number and type of CPUs. They also
contain rules for building the low level start code which is translated
using romcc and/or the GNU assembler. This code enables caches and
registers, early mtrr settings, fallback mechanisms, dram init and
possibly more.
\textbf{NOTE:} The \texttt{option} keyword can not be used in mainboard
specific configuration files. Options shall instead be set using the
\texttt{default} keyword so that they can be overridden by the image
specific configuration files if needed.
\subsubsection{Mainboard specific keywords}
The following statements are used in mainboard specific configuration
files:
\begin{itemize}
\item \begin{verbatim}arch\end{verbatim}
Sets the CPU architecture. This should be \texttt{i386} for AMD64 boards.\\
Example:
\begin{verbatim}
arch i386 end
\end{verbatim}
\item \begin{verbatim}cpu\end{verbatim}
The cpu statement is needed once per possibly available CPU. In a
one-node system, write:
\begin{verbatim}
cpu k8 "cpu0" end
\end{verbatim}
\item \begin{verbatim}driver\end{verbatim}
The \texttt{driver} keyword adds an object file to the driver section of a
LinuxBIOS image. This means it can be used by the PCI device
initialization code. Example:
\begin{verbatim}
driver mainboard.o
\end{verbatim}
\item \begin{verbatim}object\end{verbatim}
The \texttt{object} keyword adds an object file to the LinuxBIOS image.
Per default the object file will be compiled from a \texttt{.c} file
with the same name. Symbols defined in such an object file can be used
in other object files and drivers. Example:
\begin{verbatim}
object reset.o
\end{verbatim}
\item \begin{verbatim}makerule\end{verbatim}
This keyword can be used to extend the existing file creation rules
during the build process. This is useful if external utilities have to
be used for the build. LinuxBIOS on AMD64 uses romcc for it's early
startup code placed in auto.c.
To tell the configuration mechanism how to build \texttt{romcc} files,
do:
\begin{verbatim}
makerule ./auto.E
depends "$(MAINBOARD)/auto.c"
action "$(CPP) �I$(TOP)/src $(ROMCCPPFLAGS) $(CPPFLAGS) \
$(MAINBOARD)/auto.c > ./auto.E"
end
makerule ./auto.inc
depends "./auto.E ./romcc"
action "./romcc �mcpu=k8 �O ./auto.E > auto.inc"
end
\end{verbatim}
Each \texttt{makerule} section contains file dependencies (using the
texttt{depends} keyword) and an action that is taken when the dependencies
are satisfied (using the \texttt{action} keyword).
\item \begin{verbatim}mainboardinit\end{verbatim}
With the mainboardinit keyword it's possible to include assembler code
directly into the LinuxBIOS image. This is used for early infrastructure
initialization, i.e. to switch to protected mode. Example:
\begin{verbatim}
mainboardinit cpu/i386/entry16.inc
\end{verbatim}
\item \begin{verbatim}ldscript\end{verbatim}
The GNU linker ld is used to link object files together to a LinuxBIOS
ROM image.
Since it is a lot more comfortable and flexible to use the GNU linker
with linker scripts (ldscripts) than to create complex command line
calls, LinuxBIOS features including linker scripts to control image
creation. Example:
\begin{verbatim}
ldscript /cpu/i386/entry16.lds
\end{verbatim}
\item \begin{verbatim}dir\end{verbatim}
LinuxBIOS reuses as much code between the different ports as possible.
To achieve this, commonly used code can be stored in a separate
directory. For a new mainboard, it is enough to know that the code in
that directory can be used as is.
LinuxBIOS will also read a \texttt{Config.lb} file stored in that
directory. This happens with:
\begin{verbatim}
dir /pc80
\end{verbatim}
\item \begin{verbatim}config\end{verbatim}
This keyword is needed by the new chip configuration scheme. Should be
used as:
\begin{verbatim}
config chip.h
\end{verbatim}
\item \begin{verbatim}register\end{verbatim}
The \texttt{register} keyword can occur in any section, passing
additional \\
parameters to the code handling the associated device.
Example:
\begin{verbatim}
register "com1" = "{1, 0, 0x3f8, 4}"
\end{verbatim}
\item \begin{verbatim}northbridge\end{verbatim}
The \texttt{northbridge} keyword describes a system northbridge. Some
systems, like AMD64, can have more than one northbridge, i.e. one per
CPU node. Each northbridge is described by the path to the northbridge
code in LinuxBIOS (relative to \texttt{freebios2/src/northbridge}), i.e.
\texttt{amd/amdk8} and a unique name (i.e \texttt{mc0}) \\
Example:
\begin{verbatim}
northbridge amd/amdk8 "mc0"
[..]
end
\end{verbatim}
\item \begin{verbatim}southbridge\end{verbatim}
To simplify the handling of bus bridges in a LinuxBIOS system, all
bridges available in a system that are not northbridges (i.e AGP, IO,
PCIX) are seen as southbridges.
Since from the CPUs point of view any southbridge is connected via the
northbridge, a southbridge section is declared within the northbridge
section of the north bridge it is attached to.
Like the northbridge, any other bridge is described by the path to it's
driver code, and a unique name. If the described bridge is a
hypertransport device, the northbridge's hypertransport link it connects
to can be specified using the \texttt{link} keyword. Example:
\begin{verbatim}
northbridge amd/amdk8 "mc0"
[..]
southbridge amd/amd8111 "amd8111" link 0
[..]
end
[..]
end
\end{verbatim}
\item \begin{verbatim}pci\end{verbatim}
The \texttt{pci} keyword can only occur within a \texttt{northbridge} or
\texttt{southbridge} section. It is used to describe the PCI devices
that are provided by the bridge. Generally all bridge sections have a
couple of \texttt{pci} keywords.
The first occurrence of the \texttt{pci} keyword tells LinuxBIOS where
the bridge devices start, relative to the PCI configuration space used
by the bridge. The following occurences of the \texttt{pci} keyword
describe the provided devices.
Adding the option \texttt{on} or \texttt{off} to a PCI device will
enable or disable this device. This feature can be used if some bridge
devices are not wired to hardware outputs and thus are not used.
Example:
\begin{verbatim}
northbridge amd/amdk8 "mc1"
pci 0:19.0
pci 0:19.0
pci 0:19.0
pci 0:19.1
pci 0:19.2
pci 0:19.3
end
\end{verbatim}
or
\begin{verbatim}
southbridge amd/amd8111 "amd8111" link 0
pci 0:0.0
pci 0:1.0 on
pci 0:1.1 on
pci 0:1.2 on
pci 0:1.3 on
pci 0:1.5 off
pci 0:1.6 off
pci 1:0.0 on
pci 1:0.1 on
pci 1:0.2 on
pci 1:1.0 off
[..]
end
\end{verbatim}
\item \begin{verbatim}superio\end{verbatim}
SuperIO devices are basically handled like brigdes. They are taking
their driver code from \texttt{freebios2/src/superio/}. They don't
provide a PCI compatible configuration interface, but instead are ISA
PnP devices. Normally they are connected to a southbridge. If this is
the case, the \texttt{superio} section will be a subsection of the
\texttt{southbridge} section of the southbridge it is connected to.
Example:
\begin{verbatim}
superio NSC/pc87360 link 1
pnp 2e.0
pnp 2e.1
pnp 2e.2
pnp 2e.3
pnp 2e.4
pnp 2e.5
pnp 2e.6
pnp 2e.7
pnp 2e.8
pnp 2e.9
pnp 2e.a
register "com1" = "{1, 0, 0x3f8, 4}"
register "lpt" = "{1}"
end
\end{verbatim}
\end{itemize}
\newpage
\subsubsection{Mainboard specific configuration options}
The following options are commonly used in mainboard specific
configuration files.
They should be set using the \texttt{default} keyword:
\begin{itemize}
\item \begin{verbatim}HAVE_HARD_RESET\end{verbatim}
If set to \texttt{1}, this option defines that there is a hard reset
function for this mainboard. This option is not defined per default.
\item \begin{verbatim}HAVE_PIRQ_TABLE\end{verbatim}
If set to \texttt{1}, this option defines that there is an IRQ Table for
this mainboard. This option is not defined per default.
\item \begin{verbatim}IRQ_SLOT_COUNT\end{verbatim}
Number of IRQ slots. This option is not defined per default.
\item \begin{verbatim}HAVE_MP_TABLE\end{verbatim}
Define this option to build an MP table (v1.4). The default is not to
build an MP table.
\item \begin{verbatim}HAVE_OPTION_TABLE\end{verbatim}
Define this option to export a CMOS option table. The default is not to
export a CMOS option table.
\item \begin{verbatim}CONFIG_SMP\end{verbatim}
Set this option to \texttt{1} if the mainboard supports symmetric
multiprocessing (SMP). This option defaults to \texttt{0} (no SMP).
\item \begin{verbatim}CONFIG_MAX_CPUS\end{verbatim}
If \begin{verbatim}CONFIG_SMP\end{verbatim} is set, this option defines
the maximum number of CPUs (i.e. the number of CPU sockets) in the
system. Defaults to \texttt{1}.
\item \begin{verbatim}CONFIG_IOAPIC\end{verbatim}
Set this option to \texttt{1} to enable IOAPIC support. This is
mandatory if you want to boot a 64bit Linux kernel on an AMD64 system.
\item \begin{verbatim}STACK_SIZE\end{verbatim}
LinuxBIOS stack size. The size of the function call stack defaults to
\texttt{0x2000} (8k).
\item \begin{verbatim}HEAP_SIZE\end{verbatim}
LinuxBIOS heap size. The heap is used when LinuxBIOS allocates memory
with malloc(). The default heap size is \texttt{0x2000}, but AMD64 boards
generally set it to \texttt{0x4000} (16k)
\item \begin{verbatim}XIP_ROM_BASE\end{verbatim}
Start address of area to cache during LinuxBIOS execution directly from
ROM.
\item \begin{verbatim}XIP_ROM_SIZE\end{verbatim}
Size of area to cache during LinuxBIOS execution directly from ROM
\item \begin{verbatim}CONFIG_COMPRESS\end{verbatim}
Set this option to \texttt{1} for a compressed image. If set to
\texttt{0}, the image is bigger but will start slightly faster (since no
decompression is needed).
\end{itemize}
\newpage
%
% 10. Tweaking the source code
%
\section{Tweaking the source code}
Besides configuring the existing code it is sometimes necessary or
desirable to tweak certain parts of LinuxBIOS by direct changes to the
code. This chapter covers some possible enhancements and changes that
are needed when porting LinuxBIOS to a new mainboard or just come
handy now and then.
\subsection{Hypertransport configuration}
Before LinuxBIOS is able to activate all CPUs and detect bridges
attached to these CPUs (and thus, see all devices attached to the
system) it has to initialize the coherent hypertransport devices.
The current algorithms to do coherent hypertransport initialization are
not fully, automatically evaluating the hypertransport chain graph.
Therefore the code needs to be adapted when porting LinuxBIOS to a new
AMD64 mainboard. An example arrangement of hypertransport devices
looks like this:
\begin{figure}[htb]
\centering
\includegraphics[scale=1.0]{hypertransport.pdf}
\caption{Example: Hypertransport Link Connections}
\label{fix:hypertransport}
\end{figure}
Each hypertransport device has one to three hypertransport links that
are used for device interconnection. These links are called LDT$[$012$]$, or
accordingly UP, ACROSS, DOWN. Communication between the hypertransport
devices can be freely routed, honoring the physical wiring. Teaching the
coherent hypertransport initialization algorithm this wiring happens in
two steps.
\newpage
\begin{enumerate}
\item Setting outgoing connections
The algorithm needs to know which outgoing port of a CPU node is
connected to the directly succeeding node. This is done in
\texttt{freebios2/src/mainboard/$<$vendor$>$/$<$mainboard$>$/auto.c}
with a number of preprocessor defines (one define for two-node systems,
three defines for four-node systems).
The ports in question are flagged with a circle in the graph for
illustration. For the example graph above (all outgoing connections are
realized using LDT1/ACROSS) the defines are:
\begin{verbatim}
#define CONNECTION_0_1 ACROSS
#define CONNECTION_0_2 ACROSS
#define CONNECTION_1_3 ACROSS
\end{verbatim}
\item Describing routing information between CPUs.
There are basically three different message types for hypertransport
communication:
\begin{enumerate}
\item request packages
\item response packages
\item broadcast packages
\end{enumerate}
These three message types are routed using different hypertransport
ports. The routing information is written to the AMD K8 routing table.
In an Nnode system this routing table consists of 3*N*N entries , one
for each message type and for each possible CPU --> CPU communication. For
simplicity LinuxBIOS keeps the 3 routing entries for each CPU --> CPU
communication in one machine word. The routing table of each node looks
like this:
\begin{verbatim}
/* Routing Table for Node i
*
* F0: 0x40, 0x44, 0x48, 0x4c, 0x50, 0x54, 0x58, 0x5c
* i: 0, 1, 2, 3, 4, 5, 6, 7
*
* [ 0: 3] Request Route
* [0] Route to this node
* [1] Route to Link 0
* [2] Route to Link 1
* [3] Route to Link 2
* [11: 8] Response Route
* [0] Route to this node
* [1] Route to Link 0
* [2] Route to Link 1
* [3] Route to Link 2
* [19:16] Broadcast route
* [0] Route to this node
* [1] Route to Link 0
* [2] Route to Link 1
* [3] Route to Link 2
*/
\end{verbatim}
The routing table is passed to the coherent hypertransport
initialization algorithm by defining a function called
\texttt{generate\_row()} in \texttt{auto.c}:
\begin{verbatim}
static unsigned int generate_row
(uint8_t node, uint8_t row, uint8_t maxnodes)
\end{verbatim}
This function is trivial if there is only one CPU in the system, since
no routing has to be done:
\begin{verbatim}
static unsigned int generate_row
(uint8_t node, uint8_t row, uint8_t maxnodes)
{
return 0x00010101; /* default row entry */
}
\end{verbatim}
On a two-node system things look slightly more complicated. Since the
coherent hypertransport initialization algorithm works by consecutively
enabling CPUs, it contains routing information for driving the system
with one node and two nodes:
\begin{verbatim}
static unsigned int generate_row
(uint8_t node, uint8_t row, uint8_t maxnodes)
{
uint32_t ret=0x00010101; /* default row entry */
static const unsigned int rows_2p[2][2] = {
{ 0x00050101, 0x00010404 },
{ 0x00010404, 0x00050101 }
};
if(maxnodes>2) maxnodes=2;
if (!(node>=maxnodes || row>=maxnodes)) {
ret=rows_2p[node][row];
}
return ret;
}
\end{verbatim}
Systems with four nodes have to contain routing information for one, two
and four-node setups:
\begin{verbatim}
static unsigned int generate_row
(uint8_t node, uint8_t row, uint8_t maxnodes)
{
uint32_t ret=0x00010101; /* default row entry */
static const unsigned int rows_2p[2][2] = {
{ 0x00030101, 0x00010202 },
{ 0x00010202, 0x00030101 }
};
static const unsigned int rows_4p[4][4] = {
{ 0x00070101, 0x00010202, 0x00030404, 0x00010204 },
{ 0x00010202, 0x000b0101, 0x00010208, 0x00030808 },
{ 0x00030808, 0x00010208, 0x000b0101, 0x00010202 },
{ 0x00010204, 0x00030404, 0x00010202, 0x00070101 }
};
if (!(node>=maxnodes || row>=maxnodes)) {
if (maxnodes==2)
ret=rows_2p[node][row];
if (maxnodes==4)
ret=rows_4p[node][row];
}
return ret;
}
\end{verbatim}
\end{enumerate}
\subsection{DRAM configuration}
Setting up the RAM controller(s) is probably the most complex part of
LinuxBIOS. Basically LinuxBIOS serially initializes all RAM controllers
in the system, using SPDROM (serial presence detect) data to set
timings, size and other properties. The SPD data is usually read
utilizing the I2C SMBUS interface of the southbridge.
There is one central data structure that describes the RAM controllers
available on an AMD64 system and the associated devices:
\begin{verbatim}
struct mem_controller {
unsigned node_id;
device_t f0, f1, f2, f3;
uint8_t channel0[4];
uint8_t channel1[4];
};
\end{verbatim}
Available mainboard implementations and CPUs create the need to add
special setup code to RAM initialization in a number of places.
LinuxBIOS provides hooks to easily add code in these places without
having to change the generic code. Whether these hooks have to be used
depends on the mainboard design. In many cases the functions executed
by the hooks just carry out trivial default settings or they are even
empty.
Some mainboard/CPU combinations need to trigger an additional memory
controller reset before the memory can be initialized properly. This is,
for example, used to get memory working on preC stepping AMD64
processors. LinuxBIOS provides two hooks for triggering onboard memory
reset logic:
\begin{itemize}
\item \begin{verbatim}static void memreset_setup(void)\end{verbatim}
\item \begin{verbatim}static void memreset(int controllers, const struct
mem_controller *ctrl)\end{verbatim}
\end{itemize}
Some mainboards utilize an SMBUS hub or possibly other mechanisms to
allow using a large number of SPDROMs and thus ram sockets. The result
is that only the SPDROM information of one cpu node is visible at a
time. The following function, defined in \texttt{auto.c}, is called every time
before a memory controller is initialized and gets the memory controller
information of the next controller as a parameter:
\begin{verbatim}
static inline void activate_spd_rom (const struct mem_controller *ctrl)
\end{verbatim}
The way SMBUS hub information is coded into the \texttt{mem\_controller}
structure is mainboard implementation specific and not
described here. See \texttt{freebios2/src/mainboard/amd/quartet/auto.c}
for an example.
LinuxBIOS folks have agreed on SPD data being the central information
source for RAM specific information. But not all mainboards/RAM
modules feature a physical SPD ROM. To still allow an easy to use SPD
driven setup, there is a hook that abstracts reading the SPD ROM
ingredients that are used by the memory initialization mechanism:
\begin{verbatim}
static inline int spd_read_byte(unsigned device, unsigned address)
\end{verbatim}
This function, defined in \texttt{auto.c}, directly maps it's calls to
\texttt{smbus\_read\_byte()} calls if SPD ROM information is read via
the I2C SMBUS:
\begin{verbatim}
static inline int spd_read_byte(unsigned device, unsigned address)
{
return smbus_read_byte(device & 0xff, address);
}
\end{verbatim}
If there is no SPD ROM available in the system design, this function
keeps an array of SPD ROM information hard coded per logical RAM module.
It returns the �faked' SPD ROM information using device and address
as indices to this array.
\subsection {IRQ Tables}
Mainboards that provide an IRQ table should have the following two
variables set in their \texttt{Config.lb} file:
\begin{verbatim}
default HAVE_PIRQ_TABLE=1
default IRQ_SLOT_COUNT=7
\end{verbatim}
This will make LinuxBIOS look for the file \\
\texttt{freebios2/src/mainboard/<vendor>/<mainboard>/irq\_tables.c} which
contains the source code definition of the IRQ table. LinuxBIOS corrects
small inconsistencies in the IRQ table during startup (checksum and
number of entries), but it is not yet writing IRQ tables in a completely
dynamic way.
\textbf{NOTE:} To get Linux to understand and actually use the IRQ
table, it is not always a good idea to specify the vendor and device id
of the actually present interrupt router device. Linux 2.4 for example
does not know about the interrupt router of the AMD8111 southbridge. In
such cases it is advised to choose the vendor/device id of a compatible
device that is supported by the Linux kernel. In case of the AMD8111
interrupt router it is advised to specify the AMD768/Opus interrupt
controller instead (vendor id=\texttt{0x1022}, device id=\texttt{0x7443})
\subsection {MP Tables}
LinuxBIOS contains code to create MP tables conforming the
Multiprocessor Specification V1.4. To include an MP Table in a LinuxBIOS
image, the following configuration variables have to be set (in the
mainboard specific configuration file
\texttt{freebios2/src/mainboard/<vendor><mainboard>/Config.lb}):
\begin{verbatim}
default CONFIG_SMP=1
default CONFIG_MAX_CPUS=1 # 2,4,..
default HAVE_MP_TABLE=1
\end{verbatim}
LinuxBIOS will then look for a function for setting up the MP table in
the file \texttt{freebios2/src/mainboard<vendor>/<mainboard>/mptable.c}:
\begin{verbatim}
void *smp_write_config_table(void *v, unsigned long * processor_map)
\end{verbatim}
MP Table generation is still somewhat static, i.e. changing the bus
numbering will force
you to adopt the code in mptable.c. This is subject to change in future
revisions.
\subsection {ACPI Tables}
There is initial ACPI support in LinuxBIOS now. Currently the only gain with
this is the ability to use HPET timers in Linux. To achieve this, there is a
framework that can generate the following tables:
\begin{itemize}
\item RSDP
\item RSDT
\item MADT
\item HPET
\end{itemize}
To enable ACPI in your LinuxBIOS build, add the following lines to your
configuration files:
\begin{verbatim}
uses HAVE_ACPI_TABLES
[..]
option HAVE_ACPI_TABLES=1
\end{verbatim}
To keep Linux doing it's pci ressource allocation based on IRQ tables and MP
tables, you have to specify the kernel parameter \texttt{pci=noacpi} otherwise
your PCI devices won't get interrupts.
It's likely that more ACPI support will follow, when there is need for certain
features.
\subsection{POST}
LinuxBIOS has three different methods of handling POST codes. They can
be triggered using configuration file options.
\begin{itemize}
\item
\emph{Ignore POST completely}. No early code debugging is possible with
this setting. Set the configuration variable \texttt{NO\_POST} to
\texttt{1} to switch off all POST handling in LinuxBIOS.
\item
\emph{Normal IO port 80 POST}. This is the default behavior of
LinuxBIOS. No configuration variables have to be set. To be able to see
port 80 POST output, you need a POST expansion card for ISA or PCI. Port
80 POST allows simple debugging without any other output method
available (serial interface or VGA display)
\item
\emph{Serial POST}.
This option allows to push POST messages to the serial interface instead
of using IO ports. \textbf{NOTE:} The serial interface has to be
initialized before serial POST can work. To use serial POST, set the
configuration variable \texttt{CONFIG\_SERIAL\_POST} to the value 1.
\end{itemize}
\subsection{HDT Debugging}
If you are debugging your LinuxBIOS code with a Hardware Debug Tool
(HDT), you can find the source code line for a given physical EIP
address as follows: Look the address up in the file linuxbios.map. Then
search the label Lxx in the file auto.inc created by romcc. The original
source code file and line number is mentioned in auto.inc.
\subsection{Device Drivers}
With only a few data structures LinuxBIOS features a simple but flexible
device driver interface. This interface is not intended for autonomously
driving the devices but to initialize all system components so that they
can be used by the booted operating system.
Since nowadays most systems are PCI centric, the data structures used
are tuned towards (onboard and expansion bus) PCI devices. Each driver
consists of at least two structures.
The \texttt{pci\_driver} structure maps PCI vendor/device id pairs to a
second structure that describes a set of functions that together
initialize and operate the device:
\begin{verbatim}
static void adaptec_scsi_init(struct device *dev)
{
[..]
}
static struct device_operations lsi_scsi_ops = {
.read_resources = pci_dev_read_resources,
.set_resources = pci_dev_set_resources,
.enable_resources = pci_dev_enable_resources,
.init = lsi_scsi_init,
.scan_bus = 0,
};
static struct pci_driver lsi_scsi_driver __pci_driver = {
.ops = &lsi_scsi_ops,
.vendor = 0xXXXX,
.device = 0xXXXX,
};
\end{verbatim}
By separating the two structures above, M:N relations between compatible
devices and drivers can be described. The driver source code containing
above data structures and code have to be added to a LinuxBIOS image
using the driver keyword in the mainboard specific configuration file \\
\texttt{freebios2/src/mainboard/<vendor>/<mainboard>/Config.lb}:
\begin{verbatim}
driver lsi_scsi.o
\end{verbatim}
\subsection{Bus Bridges}
Currently all bridges supported in the LinuxBIOS2 tree are transparent
bridges. This means, once the bridge is initialized, it's remote devices
are visible on one of the PCI buses without special probing. LinuxBIOS
supports also bridges that are nontransparent. The driver support code
can provide a \texttt{scan\_bus} function to scan devices behind the bridge.
\subsection{CPU Reset}
When changing speed and width of hypertransport chain connections
LinuxBIOS has to either assert an LDTSTOP or a reset to make the changes
become active. Additionally Linux can do a firmware reset, if LinuxBIOS
provides the needed infrastructure. To use this capability, define the
option \texttt{HAVE\_HARD\_RESET} and add an object file specifying the
reset code in your mainboard specific configuration file
\texttt{freebios2/src/mainboard/$<$vendor$>$/$<$mainboard$>$/Config.lb}:
\begin{verbatim}
default HAVE_HARD_RESET=1
object reset.o
\end{verbatim}
The C source file \texttt{reset.c} (resulting in \texttt{reset.o}
during compilation) shall define the following function to take care
of the system reset:
\begin{verbatim}
void hard_reset(void);
\end{verbatim}
See \texttt{freebios2/src/mainboard/arima/hdama/reset.c} for an example
implementation.
\newpage
%
% 11. LinuxBIOS Internals
%
\section{LinuxBIOS Internals}
This chapter covers some of the internal structures and algorithms of
LinuxBIOS that have not been mentioned so far.
\subsection{Code Flow}
\begin{figure}[htb]
\centering
\includegraphics[scale=0.7]{codeflow.pdf}
\caption{LinuxBIOS rough Code Flow}
\label{fix:codeflow}
\end{figure}
\newpage
\subsection{Fallback mechanism}
LinuxBIOS provides a mechanism to pack two different LinuxBIOS builds
within one LinuxBIOS ROM image. Using the system CMOS memory LinuxBIOS
determines whether the last boot with a default image succeeded and
boots a failsafe image on failure. This allows insystem testing without
the risk to render the system unusable. See
\texttt{freebios2/src/mainboard/arima/hdama/failover.c} for example
code. The fallback mechanism can be used with the \texttt{cmos\_util}.
\subsection{(Un) Supported Standards}
LinuxBIOS supports the following standards
\begin{itemize}
\item Multiprocessing Specification (MPSPEC) 1.4
\item IRQ Tables (PIRQ)
\item ACPI (initial support on AMD64)
\item Elf Booting
\end{itemize}
However, the following standards are not supported until now, and will
probably not be supported in future revisions:
\begin{itemize}
\item APM
\end{itemize}
\subsection{LinuxBIOS table}
LinuxBIOS stores information about the system in a data structure called
the LinuxBIOS table. This table can be read under Linux using the tool
lxbios from the Lawrence Livermore National Laboratory.
Get more information about lxbios and the utility itself at
\url{http://www.llnl.gov/linux/lxbios/lxbios.html}
\subsection{ROMCC limitations}
ROMCC, part of the LinuxBIOS project, is a C compiler that translates to
completely rommable code. This means the resulting code does not need
any memory to work. This is one of the major improvements in LinuxBIOS
V2, since it allows almost all code to be written in C. DRAM
initialization can be factored and reused more easily among mainboards
and platforms.
Since no memory is available during this early initialization point,
romcc has to map all used variables in registers for the time being.
Same applies for their stack usage. Generally the less registers are
used up by the algorithms, the better code can be factored, resulting in
a smaller object size. Since getting the best register usage is an NP
hard problem, some heuristics are used to get reasonable translation
time. If you run out of registers during compilation, try to refactor
your code.
\subsection{CMOS handling}
LinuxBIOS can use the mainboard's CMOS memory to store information
defined in a data structure called the CMOS table . This information
contains serial line speed, fallback boot control, output verbosity,
default boot device, ECC control, and more. It can be easily enhanced by
enhancing the CMOS table. This table, if present, is found at
\texttt{freebios2/src/mainboard/$<$vendor$>$/$<$mainboard$>$/cmos.layout}.
It describes the available options, their possible values and their
position within the CMOS memory. The layout file looks as follows:
\begin{verbatim}
# startbit length config configID name
[..]
392 3 e 5 baud_rate
[..]
# configid value human readable description
5 0 115200
5 1 57600
5 2 38400
5 3 19200
5 4 9600
5 5 4800
5 6 2400
5 7 1200
\end{verbatim}
To change CMOS values from a running Linux system, use the
\texttt{cmos\_util}, provided by Linux Networks as part of the LinuxBIOS
utilities suite. Get it at
\textit{ftp://ftp.lnxi.com/pub/linuxbios/utilities/}
\subsection {Booting Payloads}
LinuxBIOS can load a payload binary from a Flash device or IDE. This
payload can be a boot loader, like FILO or Etherboot, a kernel image, or
any other static ELF binary.
To create a Linux kernel image, that is bootable in LinuxBIOS, you have
to use mkelfImage. The command line I used, looks like follows:
\begin{verbatim}
objdir/sbin/mkelfImage �t bzImagei386 �kernel /boot/vmlinuz \
�commandline="console=ttyS0,115200 root=/dev/hda3" \
�initrd=/boot/initrd �output vmlinuz.elf
\end{verbatim}
This will create the file \texttt{vmlinuz.elf} from a distribution
kernel, console redirected to the serial port and using an initial
ramdisk.
\subsection{Kernel on dhcp/tftp}
One possible scenario during testing is that you keep your kernel (or
any additional payload) on a different machine on the network. This can
quickly be done using a DHCP and TFTP server.
Use for example following \texttt{/etc/dhcpd.conf} (adapt to your
network):
\begin{verbatim}
subnet 192.168.1.0 netmask 255.255.255.0 {
range 192.168.1.0 192.168.1.31;
option broadcastaddress 192.168.1.255;
}
ddnsupdatestyle adhoc;
host hammer12 {
hardware ethernet 00:04:76:EA:64:31;
fixedaddress 192.168.1.24;
filename "vmlinuz.elf";
}
\end{verbatim}
Additionally you have to run a \texttt{tftp} server. You can start one
using \texttt{inetd}. To do this, you have to remove the comment from
the following line in \texttt{/etc/inetd.conf}:
\begin{verbatim}
tftp dgram udp wait root /usr/sbin/in.tftpd in.tftpd -s /tftpboot
\end{verbatim}
Then put your kernel image \texttt{vmlinuz.elf} in \texttt{/tftpboot} on
the \texttt{tftp} server.
\newpage
%
% 12. Advanced Device Initialization Mechanisms
%
\section{Advanced Device Initialization Mechanisms}
Like software, today's hardware is getting more and more complex. To
stay flexible many hardware vendors start breaking hardware
compatibility to old standards like VGA. Thus, VGA is still supported by
most cards, but emulation has to be enabled by the firmware for the
device to operate properly. Also, many expansion cards are small
discrete systems that have to initialize attached ram, download
controller firmware and similar. Without this initialization, an
operating system can not take advantage of the hardware, so there needs
to be a way to address this issue. There are several alternatives:
\subsection{Native LinuxBIOS Support}
For some devices (ie Trident Cyberblade 3d) there is native LinuxBIOS
support This means there is a small driver bound to the PCI id of the
device that is called after PCI device ressources are allotted.
PROs:
\begin{itemize}
\item open source
\item minimal driver
\item early control
\end{itemize}
CONs:
\begin{itemize}
\item need an additional driver
\item viable for onboard devices only
\item not flexible for pci cards
\end{itemize}
\subsection{Using Native Linux Support}
A simple way of getting a whole lot of drivers available for LinuxBIOS
is to reuse Linux drivers by putting a Linux kernel to flash. This
works, because no drivers are needed to get the Linux kernel (as opposed
to store the kernel on a harddisk connected to isa/scsi/raid storage)
PROs:
\begin{itemize}
\item large number of open source drivers
\end{itemize}
CONs:
\begin{itemize}
\item need Linux in Flash (BLOAT!)
\item drivers expect devices to be initialized (LSI1020/1030)
\item Linux only
\item large flash needed (4MBit minimum, normal operations 8+ MBit)
\end{itemize}
\subsection{Running X86 Option ROMs}
Especially SCSI/RAID controllers and graphics adapters come with a
special option rom. This option rom usually contains x86 binary code
that uses a legacy PCBIOS interface for device interaction. If this code
gets executed, the device becomes operable in Linux and other operating
systems.
PROs:
\begin{itemize}
\item really flexible
\item no need for additional drivers on firmware layer
\item large number of supported devices
\end{itemize}
CONs:
\begin{itemize}
\item non-x86 platforms need complex emulation
\item x86 platforms need legacy API
\item outdated concept
\end{itemize}
\subsection{Running Open Firmware Option ROMs}
Some PCI devices come with open firmware option roms. These devices are
normally found in computers from SUN, Apple or IBM. Open Firmware is a
instruction set architecture independent firmware standard that allows
device specific initialization using simple, small, but flexible
bytecode that runs with minimal footprint on all architectures that have
an Open Firmware implementation.
There is a free Open Firmware implementation available, called OpenBIOS,
that runs on top of LinuxBIOS. See www.openbios.org
PROs:
\begin{itemize}
\item architecture independence
\item small footprint
\item clean concept, less bugs
\end{itemize}
CONs:
\begin{itemize}
\item only small number of devices come with OpenFirmware capable option roms
\end{itemize}
%
% 13 Glossary
%
\section{Glossary}
\begin{itemize}
\item payload
LinuxBIOS only cares about lowlevel machine initialization, but also has
very simple mechanisms to boot a file either from FLASHROM or IDE. That
file, possibly a Linux Kernel, a boot loader or Etherboot, are called
payload, since it is the first software executed that does not cope with
pure initialization.
\item flash device
Flash devices are commonly used in all different computers since unlike
ROMs they can be electronically erased and reprogrammed.
\end{itemize}
\newpage
%
% 14 Bibliography
%
\section{Bibliography}
\subsection{Additional Papers on LinuxBIOS}
\begin{itemize}
\item { \small
\textit{\url{http://www.linuxnetworx.com/products/linuxbios_white_paper.pdf}}
}
\item
\textit{\url{http://www.linuxbios.org/papers/}}
\item
\textit{\url{http://www.lysator.liu.se/upplysning/fa/linuxbios.pdf}}
\item
\textit{\url{http://portal.acm.org/citation.cfm?id=512627}}
\end{itemize}
\subsection {Links}
\begin{itemize}
\item Etherboot: \textit{\url{http://www.etherboot.org/}}
\item Filo: \textit{\url{http://te.to/~ts1/filo/}}
\item OpenBIOS: \textit{\url{http://www.openbios.org/}}
\end{itemize}
\end{document}
|