| Age | Commit message (Collapse) | Author |
|---|
|
Note that against the specs, these definitions repeat
the sleep type also in the reserved fields 3 and 4.
For consistency, don't fix it here now.
Entry for \_S3 is now masked off if HAVE_ACPI_RESUME=n.
Change-Id: Icdc4c81d07fe7a99d5b0f8fa23e9443f58a40ab9
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/21143
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marc Jones <marc@marcjonesconsulting.com>
|
|
SSFG was meant to be used as a mask to enable sleepstates
_S1 thru _S4. However as a logical instead of bitwise 'and'
operation was used, all the states were enabled if only
one was marked available.
Note that all boards incorrectly had SSFG == 0x0D that previously
enabled ACPI S3 sleep state even when it was not available.
Change-Id: Ia948becff079383cbf861468da9e8a3ebbf213cb
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/21093
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marc Jones <marc@marcjonesconsulting.com>
|
|
SSFG was meant to be used as a mask to enable sleep states
_S1 thru _S4. However as a logical instead of bitwise 'and'
operation was used, all the states were enabled if only
one was marked available.
State _S3 is now set conditionally if HAVE_ACPI_RESUME=y.
For pi/hudson this had been fixed already preprocessor.
Note that all boards had SSFG == 0x0D that previously
enabled ACPI S3 sleep state even when it was not available.
States _S1 and _S2 still appear enabled in ASL/AML
but may not actually work.
TEST: 'cat /sys/power/state' and notice choice 'mem' was
removed from the list of available sleep states.
Change-Id: I27d616871c1771f0c87d8fba23d4ce1569607765
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/21091
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marc Jones <marc@marcjonesconsulting.com>
|
|
Return to empty stack before making the switch.
Change-Id: I6d6f633933fac5bc08d9542c371715f737fb42cf
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/20574
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: Raptor Engineering Automated Test Stand <noreply@raptorengineeringinc.com>
|
|
Change-Id: I5e7890aafbc8c80716ee49690e306482a482a863
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/20573
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Tested-by: Raptor Engineering Automated Test Stand <noreply@raptorengineeringinc.com>
|
|
Avoid conflicting disable_cache_as_ram() declaration and tidy
up include for inlined function.
Change-Id: Iba77c711f5eb023566b7d8ba148583948661bc99
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/20563
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Denverton_NS SoC
This change adds the FSP header files for FSP version 2.0 (15D50)
for the Intel Denverton_NS SoC.
Change-Id: I9672610df09089c549e74072345781bea0b4d06f
Signed-off-by: Mariusz Szafranski <mariuszx.szafranski@intel.com>
Reviewed-on: https://review.coreboot.org/20805
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: FEI WANG <wangfei.jimei@gmail.com>
Reviewed-by: Brenton Dong <brenton.m.dong@intel.com>
|
|
- Populate soc_intel_cannonlake_config
- Add usb.h and vr_config.h for CannonLake
Change-Id: I2a6e737594da1e766b157a38942e19a4f7fb9dfa
Signed-off-by: Pratik Prajapati <pratikkumar.v.prajapati@intel.com>
Reviewed-on: https://review.coreboot.org/21080
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
This enables adding the backlight driver to boards that may or may not
come with a keyboard backlight function.
It's the responsibility of the EC to report if that feature exists, but
that's not a big extra burden given that it already keeps track of
everything else related to the backlight.
BUG=b:64705535
BRANCH=none
CQ-DEPEND=CL:620595
TEST=configured KBLE manually and noticed the presence/absence of
/sys/devices/platform/GOOG0002:00/ on a Chrome OS Linux kernel,
corresponding to the value reported by the EC.
Change-Id: Idc36bfaa6e69581ba19b52d37af6956f63cfdb8f
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/21099
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
The Sideband Acces locking code is skipped from FSP by setting an
FSP-S UPD called PchSbAccessUnlock. This locking is being done in
coreboot during finalize.c.
This is done because coreboot was failing to disable HECI1 device
using Sideband interface during finalize.c if FSP already locks
the Sideband access mechanism before that.
So, as a solution, coreboot passes an UPD to skip the locking
in FSP, and in finalize.c, after disabling HECI, it removes the
Sideband access.
BUG=b:63877089
BRANCH=none
TEST=Build and boot poppy to check lspci not showing Intel ME
controller in the PCI device list.
Change-Id: I8dba4c97480200507969b0f2873337f97bd2ff6a
Signed-off-by: Barnali Sarkar <barnali.sarkar@intel.com>
Reviewed-on: https://review.coreboot.org/20956
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Kahlee has an ambient light sensor connected to the EC.
TEST=Can see the device in /sys/bus/iio
BUG=b:62030268
Change-Id: Id1138a0fc5270489a734bdf8b1f4ac02d358c0df
Signed-off-by: Akshu Agrawal <akshu.agrawal@amd.com>
Reviewed-on: https://review.coreboot.org/21146
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
devicetree.cb of cannonlake-u and y variant gets picked up
from src/mainboard/intel/cannonlake_rvp/variants/cnl_[u/y]
Change-Id: I83f636c93407a6fe17114582506397c46d1b4e20
Signed-off-by: Pratik Prajapati <pratikkumar.v.prajapati@intel.com>
Reviewed-on: https://review.coreboot.org/21137
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Define and populate PCI devices in devicetree for CNL-Y RVP
Change-Id: I311437798274dd48b0898f0832bf03d86fd9d3a6
Signed-off-by: Pratik Prajapati <pratikkumar.v.prajapati@intel.com>
Reviewed-on: https://review.coreboot.org/21055
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
|
|
Define and populate PCI devices in devicetree for CNL-U RVP
Change-Id: Id04f5efe77a04c180b5dd392da777195bd9fb7a3
Signed-off-by: Pratik Prajapati <pratikkumar.v.prajapati@intel.com>
Reviewed-on: https://review.coreboot.org/21054
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
|
|
This patch assigns the code of coral family, such that,
the 'mosys platform family' returns 'Google_Coral'.
BUG=b:64467244, b:64501879
BRANCH=none
TEST=Examine 'mosys platform family' w/ new firmware.
Change-Id: I1d8f8ca2166a1d80855608cf5b64b0cc7bf3dc93
Signed-off-by: Harry Pan <harry.pan@intel.com>
Reviewed-on: https://review.coreboot.org/21136
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
This update changes Cannonlake to use the new common PMC code. This
will help to reduce code duplication and streamline code bring up.
Change-Id: Ia69fee8985e1c39b0e4b104c51439bca1a5493ac
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/21062
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Configure core PRMRR first on all the cores and then follow
the SGX init sequence. Second microcode load would run the
MCHECK. To pass MCHECK, PRMRR on all cores needs to be
configured first. Hence, PRMRR configuration would be called
from soc_core_init while MP init for each core and then from
soc_init_cpus, BSP would call sgx_configure for each core
(including for itself). This code flow satisfies the MCHECK
passing pre-conditions; and apparently this patch fixes the
behavior of calling configure_sgx() “again” for BSP. (So
removed the TODO comment also).
Change-Id: I88f330eb9757cdc3dbfc7609729c6ceb7d58a0e1
Signed-off-by: Pratik Prajapati <pratikkumar.v.prajapati@intel.com>
Reviewed-on: https://review.coreboot.org/21007
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
To correct the SGX init sequence; PRMRR on all cores first
needs to be set, then follow the SGX init sequence. This
patch would refactor the common SGX code (and add needed
checks in the init sequence) so that SOC specific code can
call SGX init in correct order.
Change-Id: Ic2fb00edbf6e98de17c12145c6f38eacd99399ad
Signed-off-by: Pratik Prajapati <pratikkumar.v.prajapati@intel.com>
Reviewed-on: https://review.coreboot.org/21006
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Remove passing microcode patch pointer as param while calling
- soc_core_init()
- soc_init_cpus()
Also change callbacks in apollolake/geminilake and skylake/kabylake
common code to reflect the same function signature.
Change-Id: Ib03bb4a3063d243d97b132e0dc288ef3868a5a7b
Signed-off-by: Pratik Prajapati <pratikkumar.v.prajapati@intel.com>
Reviewed-on: https://review.coreboot.org/21010
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Early serial for W83627[HF|EHG] superios are handled by
superio/winbond/common/early_serial.c. Remove code
thus deprecated.
Build tested on select affected mainboards.
Change-Id: Idad6e0281f7a272e184feff686ce1407825429c7
Signed-off-by: Keith Hui <buurin@gmail.com>
Reviewed-on: https://review.coreboot.org/20988
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Six mainboards with Winbond superios directly configure
them in romstage.c. All use the common Winbond romstage
code. Change them to use the common config entry code to
allow for code refactoring such as [1]. Build tested.
[1] https://review.coreboot.org/20988
Change-Id: Icecd52ec622b9da86edb07c52893f4db001e5562
Signed-off-by: Keith Hui <buurin@gmail.com>
Reviewed-on: https://review.coreboot.org/20989
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Tested:
- i5-3550 and DIMM configurations: 2+0+2+2, 0+2+2+2, 2+2+2+2, 4+2+4+2
- debug output from serial port, EHCI debug port not found
- Arch Linux (Linux 4.11.5) loaded from SeaBIOS, GRUB2, and Linux payload
- all PCI and PCI Express slots
Issues:
- sometimes the machine fails to boot, with serial debug output it can
be seen it stucks after SMM initialization, and more likely to fail
to boot when serial cable is attached
- no S3 resume (not tested in vendor firmware)
Change-Id: I94fbfcee06921538b32aa3c23efa642e7e405ef6
Signed-off-by: Iru Cai <mytbk920423@gmail.com>
Reviewed-on: https://review.coreboot.org/20227
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Add two additional LED IDs.
Add Kconfig menu entries to allow selecting the action
to execute on death.
Overwrite weak die_notify method to notify user on death.
Flash all LEDs and play beep code 10 depending on Kconfig
options.
Successfully tested on:
Tested on Lenovo T500.
Tested on Lenovo X200.
Tested on Lenovo T430, but only LEDs are flashing.
Change-Id: Id34d399f154952a48c1f4ccb0c41a238b2d7ccb8
Signed-off-by: Patrick Rudolph <siro@das-labor.org
Reviewed-on: https://review.coreboot.org/19695
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Current coreboot does not create ACPI device for OS to recognize Raydium
touchscreen.
List the touch screen in the devicetree so that the correct ACPI device
are created.
BUG=b:64821783
BRANCH=reef
TEST=emerge-snappy coreboot
Change-Id: I8852e38f01f82b80c2c9718b93baf5894dbd745b
Signed-off-by: Kevin Chiu <Kevin.Chiu@quantatw.com>
Reviewed-on: https://review.coreboot.org/21083
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Current coreboot does not create ACPI device for OS to recognize MELFAS
touchscreen.
List the touch screen in the devicetree so that the correct ACPI device
are created.
BUG=b:64779224
BRANCH=reef
TEST=emerge-snappy coreboot
Change-Id: If2bc910d641e0cf2b120ed883c5788542959f568
Signed-off-by: Kevin Chiu <Kevin.Chiu@quantatw.com>
Reviewed-on: https://review.coreboot.org/21067
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Get microcode patch pointer from intel_mp_current_microcode() api
of mp_init and change sgx_configure function signature to drop
microcode_patch param.
Change-Id: I9196c30ec7ea52d7184a96b33835def197e2c799
Signed-off-by: Pratik Prajapati <pratikkumar.v.prajapati@intel.com>
Reviewed-on: https://review.coreboot.org/21009
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Select LPSS UART Base address based on LPSS UART port index.
Change-Id: I31b239e7e6b7e9ac8ea2fcfbcbd8cb148ef9e586
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/20999
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Select LPSS UART Base address based on LPSS UART port index.
Change-Id: I306d3d299f8d6a890ae519c74008f9d0d9dd1a76
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/20997
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Cannonlake SOC has two possible ways to make serial
console functional.
1. Legacy IO based access using Port 0x3F8.
2. LPSS UART PCI based access.
This patch to provide option to select index for LPSS
UART port: 0 = LPSS UART0, 1 = LPSS UART1, 2 = LPSS UART2
PCI based LPSS UART2 is by default enabled for Chrome Design.
Change-Id: I7afa5ab2c5eb06e6df8eeb1cb1cd0de00d2b2a28
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/20998
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Skylake/Kabylake SOC has two possible ways to make serial
console functional.
1. Legacy IO based access using Port 0x3F8.
2. LPSS UART PCI based access.
This patch to provide option to select index for LPSS
UART port: 0 = LPSS UART0, 1 = LPSS UART1, 2 = LPSS UART2
PCI based LPSS UART2 is by default enabled for Chrome Design.
Change-Id: I9647820fe59b5d1a1001a611b9ae3580946da0ae
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/20996
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Remove the duplicate MISCCFG_GPE0_DW* macros that are already present
in the common gpio code.
Change-Id: Iad75e5f7e276b37b5861f0c9a3bb0bb2824a638c
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/21078
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Add mp_current_microcode() function to get the microcode patch pointer.
Use this function to avoid reading the microcode patch from the boot
media. init_cpus() would initialize microcode_patch global variable to
point to microcode patch in boot media and this function can be used
to access the pointer.
Change-Id: Ia71395f4e5b2b4fcd4e4660b66e8beb99eda65b8
Signed-off-by: Pratik Prajapati <pratikkumar.v.prajapati@intel.com>
Reviewed-on: https://review.coreboot.org/21061
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
FSP might have done some settings for us there. Use pci_update_config32()
since the register is documented to be 32 bits wide.
Change-Id: I995e8a731a6958f10600174d031bb94f5a0a66db
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/21072
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Update Psi2Threshold, IccMax, ACLoadline and DCLoadline VR config
settings to match that of soraka.
BUG=b:62063434
BRANCH=None
TEST=Build and boot poppy.
Change-Id: I2c294eb14257d319e1e2d4d1e529481d921ba6f8
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/21105
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Rajneesh Bhardwaj <rajneesh.bhardwaj@intel.com>
|
|
Poppy uses MPS2949 IMVP8 controller and does not need the VR
workaround similar to Eve.
Change-Id: If6fb1890e024e1488d278bbe0a71a1a63ee321af
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/21104
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Rajneesh Bhardwaj <rajneesh.bhardwaj@intel.com>
|
|
Relevant changes (commit 2e8761e):
* Add an option to truncate the ME image file
* Add full support for Skylake (ME 11) and following, including
modules removal, truncation informations and partition
relocation
* Add two options to generate a shrinked ME image file and the
corresponding descriptor with a modified flash layout
* Update README.md
* Bug fixes
Also add a link to the usage guide in the Kconfig help.
Change-Id: I690c5d558139f64f38babf3c0988b53834ba8b37
Signed-off-by: Nicola Corna <nicola@corna.info>
Reviewed-on: https://review.coreboot.org/20915
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
|
|
Clear LAST_BYTE flag at beginning of block commands.
For reads, slave device determines in the message format how
many bytes it has to transfer out, host firmware only dictates
the maximum buffer length. Return SMBUS_ERROR if only
partial message was received.
For writes, return SMBUS_ERROR if length > 32.
For writes, fix off-by-one error reading memory one
byte past the buffer end.
Change-Id: If9e5d24255a0a03039b52d2863bc278d0eefc311
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/20879
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
A small typo in the dll setting code prevented this combination from
booting.
TESTED on ga-g41m-es2l with 800MHz FSB CPU and 667MHz ddr2
Change-Id: Ib013471773c20336ba0902b7f328bfb6ef970747
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/20981
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
|
|
Moves receive enable calibration to a separate file to lighten
raminit.c a bit.
Receive enable calibration is quite similar to gm45 so it reuses some
of its function names.
The functional changes are:
* the minimum coarse is now reset for each channel;
* on the second fine search for DQS high, TAP overflow is handled by
increasing medium;
* start coarse at CAS + 1 instead of CAS - 1. Other Intel northbridges
do the same and the results are more in line with register dumps
from vendor bios.
These might improve stability.
TESTED on ga-g41m-es2l
Change-Id: I0c970455e609d3ce96a262cbf110336a2079da4d
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/18692
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
On this device libgfxinit successfully initializes textmode and
framebuffer mode on the device connected to the HDMI1 port.
VGA port is not tested, due to lack of VGA with valid EDID.
Every ports works on GNU/Linux with kernel version 4.9+80+deb9u1.
Due to limitations within the libgfxinit's current build system,
it needs "select NORTHBRIDGE_INTEL_IVYBRIDGE" to work, even it is
PCH instead of CPU for which libgfxinit should be configured here.
Change-Id: Ib1513fc57b79eebc5d047c2e24585731c44bc215
Signed-off-by: Bill XIE <persmule@gmail.com>
Reviewed-on: https://review.coreboot.org/21071
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Fail at build-time if one of the following happens:
Platform includes SMI handler setup function smm_init()
in the build when configuration has HAVE_SMI_HANDLER=n.
Platform does not implement smm_init_completion() when
HAVE_SMI_HANDLER=y.
Change-Id: I7d61c155d2b7c2d71987980db4c25d520452dabf
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/21097
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Fix low memory corruption on S3 resume path.
Affected platforms were sandy/ivybridge.
Change-Id: I7379e7396b61ee4dc2438276d530feffaa1bc8f2
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/21100
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
|
|
SMM relocation code overwrite low memory owned by OS.
Change-Id: Ifa3d28bed3d3db65b0707bde62ae2b424a231f1a
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/19405
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Change-Id: I7c138758707f87c0d7a827b6887c7752d3714cde
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/21088
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Change-Id: I2d6fdfd0465fe5f558daa04c6f980f7226596b55
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/21087
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Instead of enabling power button SMI unconditionally, add a boot state
handler to enable power button SMI just before jumping to
payload. This ensures that:
1. We do not respond to power button SMI until we know that coreboot
is done.
2. On resume, there is no need to enable power button SMI. This avoids
any power button presses during resume path from triggering a
shutdown.
BUG=b:64811381
Change-Id: Icc52dc0103555602c23e09660bc38bb4bfddbc11
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/21082
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
|
|
... is enabled. Otherwise we are compiling an effectively
empty file.
Change-Id: I4e3d982066d1fa66a3da5f37e278ec7fd5bb1ea8
Signed-off-by: Keith Hui <buurin@gmail.com>
Reviewed-on: https://review.coreboot.org/21023
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Idwer Vollering <vidwer@gmail.com>
|
|
Reuse generic I2C functions that work for SMBus operations as well.
Change-Id: I5a93f17b905de38752254891aa4347ba4ed3b205
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/20855
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Change-Id: Ib31e77eec639c231520198c0b978d6c3c1eadaed
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/20454
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Do not use the global platform_i2c_transfer() function that can only be
implemented by a single driver. Instead, make a `struct device` aware
transfer() function the only interface function for I2C controller dri-
vers to implement.
To not force the slave device drivers to be implemented either above
generic I2C or specialized SMBus operations, we support SMBus control-
lers in the slave device interface too.
We start with four simple slave functions: i2c_readb(), i2c_writeb(),
i2c_readb_at() and i2c_writeb_at(). They are all compatible to respec-
tive SMBus functions. But we keep aliases because it would be weird to
force e.g. an I2C EEPROM driver to call smbus_read_byte().
Change-Id: I98386f91bf4799ba3df84ec8bc0f64edd4142818
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/20846
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Split `i2c.h` into three pieces to ease reuse of the generic defi-
nitions. No code is changed.
* `i2c.h` - keeps the generic definitions
* `i2c_simple.h` - holds the current, limited to one controller driver
per board, devicetree independent I2C interface
* `i2c_bus.h` - will become the devicetree compatible interface for
native I2C (e.g. non-SMBus) controllers
Change-Id: I382d45c70f9314588663e1284f264f877469c74d
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/20845
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
The code is based on autoport. I'm using a machine with discrete GPU,
and gfx.* in devicetree.cb is from 2760p.
It can be debug with serial port on dock.
Tested:
- CPU and memory: i5-2540M, 4G+0
- Arch Linux (Linux 4.11.7, SeaBIOS payload, with ATOM BIOS extracted
from vendor UEFI firmware)
- USB ports
- SD card reader
- WLAN
- DP display
- S3
Change-Id: I9c42723ba240a2e9b46998c1a8a708aebc66c604
Signed-off-by: Iru Cai <mytbk920423@gmail.com>
Reviewed-on: https://review.coreboot.org/20501
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
The code is based on autoport. The EHCI debug port is the upper USB
port beside the battery.
Tested and working:
- CPU and memory: i7-3720QM, 4G+4G
- Linux Mint with Linux 4.4 (SeaBIOS payload)
- All USB ports
- ExpressCard
- WLAN
- AC and battery status
- S3
- Other devices detected: DVD drive, smartcard reader, fingerprint, bluetooth
Not tested:
- VGA and DP
- Ethernet and modem
- Dock
Change-Id: I9f3cd124fc676d49add59e9f0a07f70a6bb0fff0
Signed-off-by: Iru Cai <mytbk920423@gmail.com>
Reviewed-on: https://review.coreboot.org/20489
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
The code is based on the code generated by autoport.
The EHCI debug port is between the DP port and eSATA port.
The serial port on dock can also be used for debugging.
The model with discrete graphics is not tested.
Tested and work:
- memory: 0+4G, 4G+0, 4G+4G
- Linux (Arch Linux with kernel 4.10.6) boot from SeaBIOS payload
with native graphics init
- WLAN
- keyboard, trackpoint and touchpad
- USB
- serial port on dock
- fan control
- AC and battery status
(EC) blobs:
This laptop uses SMSC KBC1126 EC, and there are two blobs needed by it.
You can use the tools in util/kbc1126/ to extract them and insert them
to the coreboot image using the following configuration:
-> Chipset
-> Add firmware images for KBC1126 firmware
Change-Id: Icbc051e2272b8ea73627940db15a56901d737472
Signed-off-by: Iru Cai <mytbk920423@gmail.com>
Reviewed-on: https://review.coreboot.org/18985
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
The code is generated by autoport.
The flash chip is socketed beside the WLAN slot. The EHCI debug port
is on right side of the laptop beside the RJ11 connector.
Things that work:
- memory: 0+8G, 4G+8G
- Linux (Linux Mint 18.1 with Linux 4.4)
- native graphics init + SeaBIOS payload with SeaVGABIOS
- all 3 USB ports
- WLAN
- WWAN
- SD card reader
- expresscard
- S3 suspend and resume
- internal flashing after IFD is unlocked and coreboot is flashed
- keyboard, trackpoint and touchpad
- fan control
- AC and battery status
Issues:
- Wacom digitizer does not work (even after I add it in DSDT)
- GRUB payload will freeze (in all Elitebooks, including chainloading GRUB
from SeaBIOS)
Things that are not tested:
- smart card reader
- cable modem
(EC) blobs:
This laptop uses SMSC KBC1126-NU as EC. It needs two blobs in the
flash chip. You can use the tools in util/kbc1126 to extract them
from OEM firmware, and use the following configuration to insert
them to coreboot image:
-> Chipset
-> Add firmware images for KBC1126 firmware
Change-Id: I3ffdb9f9c71f6c9a84e896abc3c424c8dd4bed0e
Signed-off-by: Iru Cai <mytbk920423@gmail.com>
Reviewed-on: https://review.coreboot.org/18241
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
This patch adds few helper functions in CPU common libraray code
which are mainly needed for ACPI module. The functions those are
moved to cpu common code is removed from common acpi files.
TEST= System boots properly and no regression observed.
Change-Id: Id34eb7e03069656238ca0cbdf6ce33f116e0e413
Signed-off-by: Shaunak Saha <shaunak.saha@intel.com>
Reviewed-on: https://review.coreboot.org/21051
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add SPI driver code for the SPI flash controller, including both
fast_spi and generic_spi.
Change-Id: Ie45146721f39d3cec20ff5136adf8925c75da1cd
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/21052
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Pratikkumar Prajapati <pratikkumar.v.prajapati@intel.corp-partner.google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Add callbacks for initial PCI devices enumeration.
Change-Id: Ia8a51973aa2b805d62590114bfc49968244b1668
Signed-off-by: Pratik Prajapati <pratikkumar.v.prajapati@intel.com>
Reviewed-on: https://review.coreboot.org/21053
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Chrome OS systems rely on the write status register to enable/disable
flash write protection and disabling this opcode breaks the ability
to enable or disable write protection with flashrom.
Add a configure option for this feature that will disable the opcode
for Write Status commands unless CONFIG_CHROMEOS is enabled.
Tested to ensure that a default build without CONFIG_CHROMEOS has this
option enabled while a build with CONFIG_CHROMEOS does not. Also
ensured that when this option is disabled (for Chrome OS) then flashrom
can be used with the --wp-enable and --wp-disable commands, depending
on the state of the external write protect pin.
Change-Id: Ia2ef3c3b1e10fba2c437e083f3537022f1fce84a
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/21021
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
|
|
Move the FSP-specific call for tearing down cache-as-RAM out of
postcar.c and replace it with an empty weak function.
This patch omits checking if (IS_ENABLED(CONFIG_FSP_CAR)). The
temp_ram_exit.c file with the real fsp_temp_ram_exit() is only built
when CONFIG_FSP_CAR is true.
Change-Id: I9adbb1f2a7b2ff50d9f36d5a3640f63410c09479
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/20965
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Remove cpu.h from the cache-as-ram setup and teardown files that rely
on the FSP implementation. The struct device statement causes a
build failure and there appears to be nothing needed from cpu.h in
the two .S files.
TEST: Build Google Reef with FSP_CAR selected on Chipset menu and add
FSP binaries on the Generic Drivers menu.
Change-Id: I560b730c18d7ec73b65f2e195b790e7dcacfd6bb
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/21057
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
The Giantec semiconductor GT24C16S and ON semiconductor CAT24C16
are the industrial standard electrically erasable programmable
read only memory (EEPROM's) and this patch adds ACPI objects
and power resources for NVMEM device.
Update DOVD method to set sensor IO LDO voltage and remove repetitive
code from OVFI, VCMP and NVMP power resources.
BUG=b:38326541
BRANCH=none
TEST=Build and boot soraka. Dump and verify that the generated DSDT table
has the required entries. Read the NVMEM content via sysfs interface.
Change-Id: If49ed33b7e1de1eabf317b31ceed8568dfca0aae
Signed-off-by: V Sowmya <v.sowmya@intel.com>
Reviewed-on: https://review.coreboot.org/20495
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
We do not need or use the Management Engine MBP HOB so that
step can be skipped when FSP initializes the ME.
BUG=b:64479422
TEST=boot with FSP debug enabled binary and ensure that the
output indicates this step is being skipped:
Skipping MBP data due to SkipMbpHob set!
Change-Id: I5ea22ec4b8b47fa17b1cf2bf562337bfaad5ec0d
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/20951
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
|
|
BUG=b:64705535
BRANCH=master
TEST=emerge-coral coreboot chromeos-bootimage and verify the keyboard
backlight can be bright and alt+f6, alt+f7 function keys can be used.
Change-Id: I777247a6b58d3d50b72f12ca2fcab49a06ed5431
Signed-off-by: Pan Sheng-Liang <Sheng-Liang.Pan@quantatw.com>
Reviewed-on: https://review.coreboot.org/21027
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Need to perform a dummy read in order to activate LPSS UART's
16550 8-bit compatibility mode.
TEST=Able to get serial log in both 32 bit and 8 bit mode through
LPSS UART2 based on CONFIG_DRIVERS_UART_8250MEM_32 and
CONFIG_DRIVERS_UART_8250MEM selection.
Change-Id: Ief58fdcb8a91f9951a48c3bd7490b1c7fee17e48
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/20940
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Need to perform a dummy read in order to activate LPSS UART's
16550 8-bit compatibility mode.
TEST=Able to get serial log in both 32 bit and 8 bit mode through
LPSS UART2 based on CONFIG_DRIVERS_UART_8250MEM_32 and
CONFIG_DRIVERS_UART_8250MEM selection.
Change-Id: I5f23fef4522743efd49167afb04d56032e16e417
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/20939
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Like commit c91ab1cfc that targeted AGESA f14.
MemRestore() is still broken after this fix.
Change-Id: I7457de5e0c52819560e2bfd46b9e351b00d3d386
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/20900
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Due to low-memory corruptions S3 support has now been
(at least temporarily) removed from AGESA platfroms.
Should we bring it back one day, CAR teardown on S3 path
will happen with an empty stack so ugly backup/recovery
of the stack will no longer be used.
If S3 feature is brought back, resume path code for FCH
will also see partial rewrite and agesawrapper.c file
will not be part of that.
Change-Id: Ib38c04d0e74f600e0b719940d5e2530f4c726cfd
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/20899
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
A decision has been made that boards with LATE_CBMEM_INIT
will be dropped from coreboot master starting with next
release scheduled for October 2017.
As existing implementation of CAR teardown in AGESA can only
do either EARLY_CBMEM_INIT or ACPI S3 support, choose the former.
ACPI S3 support may be brought back at a later date for
these platforms but that requires fair amount of work fixing
the MTRR issues causing low-memory corruptions.
Change-Id: I5d21cf6cbe02ded67566d37651c2062b436739a3
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/20898
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
LPC pci config register BIOS Control (BC) - offset 0xDC bit 1
is for Lock Down.
Change-Id: I4780d2e41c833c0146640f715759dbb0a948c4ab
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/21001
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
This patch fix the dependency for PMC common block code.
PMC block use SLP_TYP macros and acpi_sleep_from_pm1
function which is defined in arch/acpi.h and guarded
by CONFIG_ACPI_INTEL_HARDWARE_SLEEP_VALUES. So we need
PMC common block to depend on that config for proper
inclusion.
Change-Id: I88077626aff3efba0a95b3aaee0dbd71344ccb42
Signed-off-by: Shaunak Saha <shaunak.saha@intel.com>
Reviewed-on: https://review.coreboot.org/20964
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Rename BAR0 and BAR2 SRAM base and size macros to align with the spec.
* PMC_SRAM_BASE_0 -> SRAM_BASE_0
* PMC_SRAM_SIZE_0 -> SRAM_SIZE_0
* PMC_SRAM_BASE_1 -> SRAM_BASE_2
* PMC_SRAM_SIZE_1 -> SRAM_SIZE_2
Change-Id: I48d65c30368c4500549b535341b14ca262d7fc48
Signed-off-by: V Sowmya <v.sowmya@intel.com>
Reviewed-on: https://review.coreboot.org/20539
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch provides the option to use the common CPU
Mp Init code by selecting a Config Token.
CONFIG_SOC_INTEL_COMMON_BLOCK_CPU_MPINIT config token can be
selected to use the Common MP Init Code, also where CPU MP Init is
done before FSP-S Init.
And if the config token is not selected, the old way of
implementation will exist, where MP Init is been done after
FSP-S.
CQ-DEPEND=CL:*397551
BUG=none
BRANCH=none
TEST=Build and boot Reef
Change-Id: I35d012785000d3f3bfcc34138cda9cd4591559f6
Signed-off-by: Barnali Sarkar <barnali.sarkar@intel.com>
Reviewed-on: https://review.coreboot.org/20895
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Early serial init on this superio is done by
superio/winbond/common/early_serial.c and no board
currently references this instance anymore.
Change-Id: Iab8dd93663fc78ed0d8c6a5313bb6a1884d1a043
Signed-off-by: Keith Hui <buurin@gmail.com>
Reviewed-on: https://review.coreboot.org/20978
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Change all 440BX boards to use the combined RAM init routine added in
commit 078e3240 (northbridge/intel/i440bx: Merge RAM init routines) [1].
[1] https://review.coreboot.org/20676
Change-Id: I699db882189f99018d4a6fdcb00f9438b2a7a1bc
Signed-off-by: Keith Hui <buurin@gmail.com>
Reviewed-on: https://review.coreboot.org/20868
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Romstages of many 440BX boards included headers that are redundant.
Remove them as part of a bigger cleanup effort.
This finishes off what began in https://review.coreboot.org/20693.
Change-Id: I102a4f6e492eb607b7f88d4c6e15072a8b7fdc46
Signed-off-by: Keith Hui <buurin@gmail.com>
Reviewed-on: https://review.coreboot.org/20952
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
BUG=b:64468585
BRANCH=none
TEST=with the other sku-id related patches applied, coreboot obtains the
right SKU ID from EC
Change-Id: I96a0e030bbc5f1c98165e70353340c413f8dc352
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/20947
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
BUG=b:64468585
BRANCH=none
TEST=with the other sku-id related patches applied, coreboot obtains the
right SKU ID from EC
Change-Id: I82e324407b4b96495a3eb3d4caf110f9eae05116
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/20946
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
The following changes can make system call into FSP siliconinit and exit
from that until payloads.
1. Add frame to call fspsinit.
2. Temporarily set all the USB OC pin to 0 to pass FSP siliconinit.
This patch was merged too early, and reverted.
Originally reviewed on https://review.coreboot.org/#/c/20581
Change-Id: I14eeba575af1658ff8013c9a00bd71013566bcbe
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/20687
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Initialize postcar frame once finish FSP memoryinit
This patch was merged too early and reverted.
Originally reviewed on https://review.coreboot.org/#/c/20534
Change-Id: Id36aa44bb7a89303bc22e92e0313cf685351690a
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/20688
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add LPC common code to be shared across Intel platforms.
Also add LPC library functions to be shared across platforms.
Use common LPC code for Apollo Lake soc. Update existing Apollolake
mainboard variants {google,intel,siemens} to use new common
LPC header file.
Change-Id: I6ac2e9c195b9ecda97415890cc615f4efb04a27a
Signed-off-by: Ravi Sarawadi <ravishankar.sarawadi@intel.com>
Reviewed-on: https://review.coreboot.org/20659
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
The PCH_P2SB_EPMASK macro takes a parameter. Ensure parenthesis
are put around the parameter expansion.
Change-Id: I978e9397036ea3630434982fe4ecd698877fe0d6
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/21004
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
It was added with the words "Update the device header files" and we
maintained it for nearly 13 years :)
These functions are part of the SMBus spec but they are rarely used
and keeping them just in case increases the maintenance burden.
Change-Id: I69a1ea155a21463fc09b7b2c5b7302515a0030b2
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/20439
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
The PMIO region was moved, but not updated in the ASL. Change to
generate \_PR table runtime and to report the correct PMIO region
and length.
Fix on Kahlee, where the EC overlaps the region:
[ 0.802721] cros_ec_lpcs GOOG0004:00: couldn't reserve region0
[ 0.807446] cros_ec_lpcs: probe of GOOG0004:00 failed with error -16
BUG=b:63902389
BRANCH=none
TEST=Cros_ec_lps can reserve the region. ACPI tables are correct.
Change-Id: I870f810cc5d2edc0b842478cde5b3c164ed3b47f
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: https://review.coreboot.org/20910
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Our current struct for I2C segments `i2c_seg` was close to being compa-
tible to the Linux version `i2c_msg`, close to being compatible to SMBus
and close to being readable (e.g. what was `chip` supposed to mean?) but
turned out to be hard to fix.
Instead of extending it in a backwards compatible way (and not touching
current controller drivers), replace it with a Linux source compatible
`struct i2c_msg` and patch all the drivers and users with Coccinelle.
The new `struct i2c_msg` should ease porting drivers from Linux and help
to write SMBus compatible controller drivers.
Beside integer type changes, the field `read` is replaced with a generic
field `flags` and `chip` is renamed to `slave`.
Patched with Coccinelle using the clumsy spatch below and some manual
changes:
* Nested struct initializers and one field access skipped by Coccinelle.
* Removed assumption in the code that I2C_M_RD is 1.
* In `i2c.h`, changed all occurences of `chip` to `slave`.
@@ @@
-struct i2c_seg
+struct i2c_msg
@@ identifier msg; expression e; @@
(
struct i2c_msg msg = {
- .read = 0,
+ .flags = 0,
};
|
struct i2c_msg msg = {
- .read = 1,
+ .flags = I2C_M_RD,
};
|
struct i2c_msg msg = {
- .chip = e,
+ .slave = e,
};
)
@@ struct i2c_msg msg; statement S1, S2; @@
(
-if (msg.read)
+if (msg.flags & I2C_M_RD)
S1 else S2
|
-if (msg.read)
+if (msg.flags & I2C_M_RD)
S1
)
@@ struct i2c_msg *msg; statement S1, S2; @@
(
-if (msg->read)
+if (msg->flags & I2C_M_RD)
S1 else S2
|
-if (msg->read)
+if (msg->flags & I2C_M_RD)
S1
)
@@ struct i2c_msg msg; expression e; @@
(
-msg.read = 0;
+msg.flags = 0;
|
-msg.read = 1;
+msg.flags = I2C_M_RD;
|
-msg.read = e;
+msg.flags = e ? I2C_M_RD : 0;
|
-!!(msg.read)
+(msg.flags & I2C_M_RD)
|
-(msg.read)
+(msg.flags & I2C_M_RD)
)
@@ struct i2c_msg *msg; expression e; @@
(
-msg->read = 0;
+msg->flags = 0;
|
-msg->read = 1;
+msg->flags = I2C_M_RD;
|
-msg->read = e;
+msg->flags = e ? I2C_M_RD : 0;
|
-!!(msg->read)
+(msg->flags & I2C_M_RD)
|
-(msg->read)
+(msg->flags & I2C_M_RD)
)
@@ struct i2c_msg msg; @@
-msg.chip
+msg.slave
@@ struct i2c_msg *msg; expression e; @@
-msg[e].chip
+msg[e].slave
@ slave disable ptr_to_array @ struct i2c_msg *msg; @@
-msg->chip
+msg->slave
Change-Id: Ifd7cabf0a18ffd7a1def25d1d7059b713d0b7ea9
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/20542
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
The S3 resume path is broken on current Linux (4.11.3) and maybe
on older kernel, too.
Don't run the native graphics init when on S3 resume to fix it.
Tested on Lenovo T430.
Change-Id: Ifad145c86c2e8f019c507f97c889b70b7aa49882
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/20289
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
This patch to make code cleaner and remove unused systemagent
register macros. [same as KBL implementation]
Change-Id: I13b9c83097fc98183ea138c9087b5fc7834efd58
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/20942
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
As per GCC 7.1 compiler struct reset_reply is considered
as uninitialized inside send_heci_reset_message function.
Change-Id: I01b95d31bfb1d2e9af1704a28dacb9cfd1cdcb50
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/20941
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
This patch add new API to read LPSS CLK register. Also combine multiple
LPSS_CLOCK_CTL_REG writes into a single write inside lpss_clk_update function.
Change-Id: I420919ad9154c4cf426bc232c5eb59d95fd698d2
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/20938
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Simplify funciton names and remove reference to hudson in stoneyridge.
The southbridge in Stoney Ridge is Kern and hudson naming is
no longer accurate.
BUG=b:62200157
BRANCH=none
TEST=Build and booted on Kahlee.
Change-Id: Ide7a72dae69b881997101f1e37a1ac739901744d
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: https://review.coreboot.org/20912
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Call weak method die_notify.
The method should be overwritten in mainboard directory to signal that
a fatal error had occurred. On boards that do share the same EC and where
the EC is capable of controlling LEDs or a buzzer the method can be
overwritten in EC directory instead.
Tested on Lenovo T500.
Change-Id: I71f8ddfc96047e8a0d39f084588db1fe2f251612
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/19696
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
This allows the use of the native VGA init on boards featuring DVI-I
ports. Digital output is not supported.
Change-Id: I11a4dd68746e06c7e27ecf3e765bdd0d8cf40515
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/20890
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
These Kconfig options can be reused for the same purpose of selecting
the correct i2c pins for probing the analog output EDID in C native
graphic init. For this purpose this patch makes those options
independent of GFX_GMA and MAINBOARD_HAS_LIBGFXINIT.
Change-Id: If29c541d414e12b95d96ae9c249a7a20e863fe06
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/20894
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Copy from chrome-ec codebase, except for keeping the long-form license
header.
BUG=b:64468585
BRANCH=none
TEST=with the other sku-id related patches applied, coreboot obtains the
right SKU ID from EC
Change-Id: I513123547f3854945e827d2f7f6c0df6591886eb
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/20945
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Update PL2 override setting to 15W as per KBL Power Arch Guide.
Change-Id: I4a6f875f8c3bdb012d6ff97c1429f32db5210893
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/20943
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Migrate opregion code from northbridge/intel/common to
drivers/intel/gma in preparation for consolidation with
soc/intel/common opregion code. Rename init_igd_opregion()
for clarity and disambiguation with other implementations.
Change-Id: I2d0bae98f04dbe7e896ca34e15f24d29b6aa2ed6
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/20582
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
|
|
- let the coreboot build system insert the two blobs to the coreboot image
- EC and Super I/O initialization
- ACPI support
Tested on 2760p, 8460p, 2570p, 8470p.
Issue:
Kernel gives the following error:
ACPI Error: No handler for Region [ECRM] (...) [EmbeddedControl]
ACPI Error: Region EmbeddedControl (ID=3) has no handler
TODO:
- consider moving the Super I/O initialization code to ramstage, or
reuse the existing sio/smsc/kbc1100 code (if so, how to add the
additional kbc1126 specific functions to sio/kbc1100)
- sort out the ACPI code which is mostly from the ACPI dump of vendor
firmware
- find out why the digitizer in hp/2760p doesn't work
- GRUB payload freezing on all HP Elitebooks may be related to EC
Change-Id: I6b16eb7e26303eda740f52d667dedb7cc04b4ef0
Signed-off-by: Iru Cai <mytbk920423@gmail.com>
Reviewed-on: https://review.coreboot.org/19072
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The minimum needed defines are included here and pm.h
will be updated when the PMC code for cannonlake is uploaded.
Change-Id: Idaf2be1258b3ec71fa449b88516bcb06c730d776
Signed-off-by: Brandon Breitenstein <brandon.breitenstein@intel.com>
Reviewed-on: https://review.coreboot.org/20849
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add all missing _PCH_DEV definitions to pci_devs.h
Change-Id: I0f2eec5dff000738f41cfa6aec11b54a65f8adc3
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/20932
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
1. Add a new variable to GNVS to store information during S3 suspend
whether UART debug controller is enabled.
2. On resume, read stored GNVS variable to decide if UART debug port
controller needs to be initialized.
3. Provide helper functions required by intel/common UARRT driver for
enabling controller on S3 resume.
BUG=b:64030366
Change-Id: Idd17dd0bd3c644383f273b465a16add184e3b171
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/20888
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
