| Age | Commit message (Collapse) | Author |
|---|
|
This commit enables HECI such that interface can be used from
userspace on the dedede mainboards.
BUG=b:184219504
TEST=Build and flash drawcia, verify that Intel Flash Programming Tool
can communicate with the Converged Security Engine.
Signed-off-by: Aseda Aboagye <aaboagye@google.com>
Change-Id: I5b28c471d6554a5e14538073d48ef47da05936fc
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52196
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Verified that all accessed registers exist in all SoCs that use this
code (Carrizo, Mullins, Stoneyridge, Picasso and Cezanne at the moment)
and that the bit definitions match as well. Also at the time of writing
this patch only Picasso calls gpio_fill_wake_state, so dropping the
check won't change behavior. This also avoids having SoC specific code
that doesn't get selected by Kconfig options in the common AMD SoC
directory and also avoids having to add a check for SOC_AMD_CEZANNE to
support this functionality on Cezanne in a follow-up patch.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: If770780a67776daf81744db1b635ffd402653a47
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52223
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
There is no nb/amd/pi northbridge left in coreboot that could be paired
with the Bolton FCH, since the remaining nb/amd/pi northbridges all use
an integrated FCH (Avalon on Mullins and Kern on Carrizo) while Bolton
is a discrete FCH. I ran into this when verifying if the common soc/amd
GPIO functionality that gets added by selecting
SOC_AMD_COMMON_BLOCK_BANKED_GPIOS is valid for all chips selecting it
and that code isn't valid for Bolton that uses the old GPIO 100
interface.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Iffe876bee96e42645e1be10730b78959b1c06d59
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52222
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
To update the sx9324 registers after RF team fine-tuned the parameters.
BUG=b:172397658
BRANCH=firmware-zork-13434.B
TEST=build coreboot and verify the sx9324 function
Signed-off-by: Frank Wu <frank_wu@compal.corp-partner.google.com>
Change-Id: Ief85bc61952144a1d7a151100d89938517078ab4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51936
Reviewed-by: Kangheui Won <khwon@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
These macros aren't needed anywhere else, so reduce their visibility.
Change-Id: Ie8d14849b4fb86d34a841d4a13ee3bbb46f9f71c
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52061
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The register is 16 bits wide.
Change-Id: I58d44a17613965e0a27aab5246dcdce68e1a8201
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51950
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
The logic for bytes to copy to the function input pointer was wrong.
What it did was to loop over all 2 bytes that need to be read and only
copy the first byte.
Change-Id: Ic08cf01d800babd4a9176dfb2337411b789040f3
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52207
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Christian Walter <christian.walter@9elements.com>
|
|
The patch enables Bluetooth config in the devicetree and removes
non-existent Bluetooth PCI interface.
TEST=Verified by checking Garfield Peak controller's PID:VID(8087:0033) in
the lsusb ouput.
Output of lsusb:
Bus 004 Device 003: ID 0bda:8153 Realtek Semiconductor Corp. USB 10/100/1000 LAN
Bus 004 Device 002: ID 0bda:0411 Realtek Semiconductor Corp. 4-Port USB 3.0 Hub
Bus 004 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Bus 003 Device 003: ID 0781:55a9 SanDisk Corp. Dual Drive
Bus 003 Device 004: ID 413c:2113 Dell Computer Corp. Dell KB216 Wired Keyboard
Bus 003 Device 002: ID 0bda:5411 Realtek Semiconductor Corp. 4-Port USB 2.0 Hub
Bus 003 Device 005: ID 8087:0033 Intel Corp.
Signed-off-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Change-Id: I7a54d344ef1b0418bee56e7308977a61604b954a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52182
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Configure the power state to return to when the power is re-applied
after power failure.
BUG=b:183739671
TEST=Build and Boot to OS in Majolica and Guybrush. By default when the
power fails the device turns on after power is re-applied. When the
POWER_ON_AFTER_POWER_FAILURE is disabled, the device remains off even
after the power is re-applied.
Change-Id: I21c5da08c82156d6239450ef6921771da74cbaa1
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52049
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Introduce a power management library to handle the power resume after
power failure. Enable HAVE_POWER_STATE_AFTER_FAILURE config when this
library is enabled.
BUG=b:183739671
TEST=Build Guybrush and Majolica mainboard.
Change-Id: Iea4ea57d747425fe6714d40ba6e60f2447febf28
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51924
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Add GRXS and GTXS support. Move the gpio method into common place.
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I8ba377179d6976cf26ed0dc521d8e4eff051dc85
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52202
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
To enable WWAN we want to release it from reset start.
BUG=b:180166408
TEST=WWAN enumerates on brya
Change-Id: I4f9884d3b2fc8822dda1a6fe743c863aa6c696da
Signed-off-by: Alex Levin <levinale@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52199
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This option is not referenced anywhere. Drop it.
Change-Id: Ie59de5399a9b1713109bf334d4ad1d7f7efb91f9
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52104
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Tested with BUILD_TIMELESS=1, Asrock B85M Pro4 remains identical.
Change-Id: I5fb31f88bbf7c2f1e44924ca2d3169257a9598dd
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51888
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Change-Id: I4d949d252ca24ebd4e4ed9c7dd17ede3810a8bfd
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51884
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Tested with BUILD_TIMELESS=1, Getac P470 remains identical.
Change-Id: Ifea441ad95293ad93d11a5f2521370cfd387289b
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51883
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Tested with BUILD_TIMELESS=1, Roda RK9 remains identical.
Change-Id: I18f40d1bc3172b3c1b6b4828cefdb91aea679ba2
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51880
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Wrap `r` in parentheses to avoid unexpected behavior with compound
expressions. Fortunately, all uses of this macro do not cause issues.
Tested with BUILD_TIMELESS=1, Roda RK9 remains identical.
Change-Id: Id0f05a507c5e7e8c50e9765261d86bae73c7b5a6
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51879
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Some cases break reproducibility if refactored, and are left as-is.
Tested with BUILD_TIMELESS=1, Asus P5QL PRO remains identical.
Change-Id: I163995c0b107860449c2f36ad63e4e4ca52decb2
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51878
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The `CLKCFG_UPDATE` macro is copied from gm45 and unused. Correct it and
use the CLKCFG macros instead of magic values.
Tested with BUILD_TIMELESS=1, Asus P5QL PRO remains identical.
Change-Id: I17e972eba21282ac84c7afe10b7149cd1131fd07
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51877
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Breaking strings across multiple lines hurts greppability. Refactor the
code a bit to drop one indentation level, and then reflow the strings.
Change-Id: I0accdfd0d2c5f58e4da493ba0d4b5c6a067d92c3
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51876
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I67f38bcb1ec0fbbfb7f2f3fcfaf2f9bf2d9ac92c
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51875
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Try to unbreak long lines and user-visible strings.
Tested with BUILD_TIMELESS=1, Asus P5QL PRO remains identical.
Change-Id: I1bbf08cf665157840380517302ca581718e3cbe4
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51874
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Tested with BUILD_TIMELESS=1, Asus P5QL PRO remains identical.
Change-Id: I143e69446614ddc80562e5931c260329257fd3cb
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51873
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Bit 4 needs to be set then polled for after changing sync DLL taps.
Change-Id: I61b73998dec84710eec0d2561a6f4d88068e3373
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51872
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
These changes are not reproducible for some reason.
Change-Id: If1fcd0285c3a14686f7deb70d83a4c63d57d62fe
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51871
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Some cases break reproducibility if refactored, and are left as-is.
Tested with BUILD_TIMELESS=1, Foxconn D41S remains identical.
Change-Id: I484f04455fe4baa69888645554fcd72881ba197d
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51869
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Tested with BUILD_TIMELESS=1, Packard Bell MS2290 remains identical.
Change-Id: Ia0a086bd28b796d2cbe1c7a056922721c95612b8
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51868
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
These changes are not reproducible for some reason.
Change-Id: I43b445b8af8871db87fb86747db8a35cec75716a
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51867
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
One instance in northbridge.c breaks reproduciblity when changed.
Tested with BUILD_TIMELESS=1, Asus P8Z77-V LX2 remains identical.
Change-Id: I2148183827bcacc9e6edb91b26ad35eb2dae5090
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51866
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
There are some cases in `northbridge_topology_init` where condensing the
operation using one macro changes the binary, and have been left as-is.
Tested with BUILD_TIMELESS=1, Asrock B85M Pro4 remains identical.
Change-Id: I59c7d1f8d816b95e86d39dcbf7bc7ce8c34f0770
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51865
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The {MCH,DMI,EP}BAR macros can be used for both reading and writing.
While this can sometimes be useful, compile-time overflow checking is
limited. Moreover, and-masks need to be bit-wise negated, which is easy
to forget and may result in spurious overflow warnings, and silencing
them with a cast also suppresses true integer overflow issues.
To address these limitations and for consistency with the existing MMIO
API (arch/mmio.h and device/mmio.h), these macros will be replaced with
prefixed wrappers around MMIO API functions. However, existing platform
code needs to be refactored, and the risk of introducing regressions is
substantial. To minimize the risk of breakage, the bulk of the platform
code changes will be verified using reproducible builds.
This patch introduces the new accessors, to be put to use in follow-ups.
These accessors are implemented as macros so that subsequent commits can
be verified using reproducible builds. They will be replaced with actual
functions after refactoring all platforms.
Change-Id: I85376a9e2f6cd042b41036f90de7f9edc7ad4508
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51864
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Except for some formatting differences, the macros are equivalent.
Change-Id: I5dc4f115b0873fb96683263ecd152d3d1504647d
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51863
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Check TBT NVM FW Ready (INFR) bit to skip D3Cold for TBT when device
is in disconnected state.
Not adhering this recommendation is blocking the S0ix state transition.
BUG=b:183670327
TEST=S0ix state transition occurs with TBT disconnected.
Change-Id: Ib9b9ceee4393aeba37fdcb4e05d1b279a6ff72d2
Signed-off-by: Sugnan Prabhu S <sugnan.prabhu.s@intel.com>
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51274
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
|
|
Update FSP headers for Tiger Lake platform generated based on FSP
version 4043. Previous version was 3444.
BUG=b:178846052
BRANCH=none
TEST=none
Signed-off-by: Srinidhi N Kaushik <srinidhi.n.kaushik@intel.com>
Change-Id: Ibada380fe757d9a8b50b2ddfeb2c86b4a98cb5e2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50154
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
|
|
cbfs_mcache_real_size() has a subtle flaw: when the cache is perfectly
full to the end (so that the termination token sits exactly at the end
of the available space), the loop counting the size ends prematurely.
This means that when migrating the cache to CBMEM the terminating token
is not copied, which isn't actually noticeable unless you're looking for
a file that's not in the cache (because it doesn't exist or because not
all files fit when building).
This patch fixes the problem and slightly changes the error message for
when a cache isn't terminated (to make it more clear that this is a
different condition from a "normal" cache overflow that can happen when
building if there's not enough room to fit all files).
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: I8d89e7dadc958f97b173b3a2352f2010c8a3d1d5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52200
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
The patch enables HECI1 interface to allow OS applications to communicate
with CSE.
BUG=None
TEST=Build and boot ADLRVP. Run lspci and check pcie device (00:16.0)
Signed-off-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Change-Id: I34ff842481bdfc7933a76555ff0fd70f4fbbb9a7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52149
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
|
|
Enable I2C2 in devicetree and fill ACPI information for Codec.
BUG=b:182211161
TEST=builds
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: Ib75ef99cbca8b2f38268705704e7616b456f19d9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52179
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mathew King <mathewk@chromium.org>
|
|
Configure the BT disable GPIO to logic low in order to enable Bluetooth.
BUG=b:182211161
TEST=builds
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I7661dea682cbe0ae5e169d87e794ed6ed3c83b5e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52178
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mathew King <mathewk@chromium.org>
|
|
BUG=b:182211161
TEST=builds
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: Ie3917c10ecf37c914dbadce5949b8f4f772abd5c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52177
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mathew King <mathewk@chromium.org>
|
|
BUG=b:182211161
TEST=builds
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I29be8572bc7bb366347eabe553be49775dec46a8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52175
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mathew King <mathewk@chromium.org>
|
|
BUG=b:182211161
TEST=builds
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I483c2e77eedcb434709b67bf9b3fbca636499508
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52174
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mathew King <mathewk@chromium.org>
|
|
Enable Acoustic noise mitigation for boten and set slew rate to 1/8
which is calibrated value for the board.
BUG=b:180668001
BRANCH=dedede
TEST=build firmware to UPD and Acoustic noise test
Change-Id: I75851bd7c279feeab4ab94f4c82d55bf0e5ce316
Signed-off-by: Stanley Wu <stanley1.wu@lcfc.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52135
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Rename the Kconfig parameter to more accurately reflect what it does.
TPM can be initialised in a different stage too, for instance with
VBOOT it is done in verstage.
Change-Id: Ic0126b356e8430c04c7c9fd46d4e20022a648738
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52133
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
|
|
Some tests have to be able to catch assertion errors.
Adding CMocka mock_assert() enables that.
Additionally fix test_imd_create_tiered_empty(),
test_full_stack() and test_incorrectly_initialized_stack()
by adding missing expect_assert_failure().
Signed-off-by: Jakub Czapiga <jacz@semihalf.com>
Change-Id: I5e8dd1b198ee6fab61e2be3f92baf1178f79bf18
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51804
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
|
|
This guards code accessing the vboot context which does not exist if
vboot starts after romstage.
Change-Id: I2a38daa00d6d18df9c5e22858530814e23bb3e00
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52157
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
|
|
Use VPD variable "fsp_dimm_freq" to select DDR frequency limit.
Tested=On OCP Delta Lake, DDR frequency limit can be changed via VPD.
Signed-off-by: Tim Chu <Tim.Chu@quantatw.com>
Change-Id: I1232feae5090420d8fa42596b46f2d4dcaf9d635
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48946
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jonathan Zhang <jonzhang@fb.com>
|
|
The intel/soc/broadwell smihandler has no handler for this APM call.
Change-Id: I2bcec7cce00d433a197a9e2fb01434a2998e1452
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52167
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Configure unused GPIOs as NC
BUG=b:180830117
TEST=Build and boot lindar to OS.
Signed-off-by: Kevin Chang <kevin.chang@lcfc.corp-partner.google.com>
Change-Id: I0ba51dc262ccbf22b45d3be4b65e006f92587fd8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52151
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
|
|
Some eMMCs need 80+ms for CMD1 to complete. And the payload may need to
access eMMC in the very early stage (for example, Depthcharge needs it
20ms after started) so we have to start initialization in coreboot.
On Hayato Chromebook this can save ~100ms in total.
BUG=b:177389446
TEST=emerge-asurada coreboot
BRANCH=asurada
Signed-off-by: Wenbin Mei <wenbin.mei@mediatek.com>
Change-Id: I2f58d203e969dc1a13a479d7dc63b1b162a9ae3f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51973
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Select mmc storage config for asurada.
Build MTK host mmc driver.
BUG=b:177389446
TEST=emerge-asurada coreboot
BRANCH=asurada
Signed-off-by: Wenbin Mei <wenbin.mei@mediatek.com>
Change-Id: Iac656d57c2b834d1ce393fd991275b897e597b4b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52014
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
Add MTK host mmc driver support.
MTK host controller supports eMMC5.1 spec.
BUG=b:177389446
TEST=emerge-asurada coreboot
BRANCH=asurada
Signed-off-by: Wenbin Mei <wenbin.mei@mediatek.com>
Change-Id: I54a7749ed167c00cd631a76af7c67c654c7bc725
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51966
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
The conversion to ASL 2.0 syntax in commit 81d55cf introduced a
regression triggering a BUG in Linux when reading the battery current.
Correct the wrongly-converted calculation.
Fixes: 81d55cf ("src/ec/lenovo/h8/acpi/battery.asl: Convert to ASL 2.0")
Tested-by: Andrew A. I. <aidron@yandex.ru>
Change-Id: I1cea8f56eb0a674005582c87cad89f10a02d0701
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52144
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
selecting SOC_AMD_COMMON_BLOCK_USE_ESPI will disable the lpc decodes,
so not selecting that keeps the lpc decodes.
Change-Id: I03a8d4b804cee205b9e06b00e2e5a442452f8f86
Signed-off-by: Ritul Guru <ritul.bits@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52016
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
These changes involve NVMe specific GPIO programming to enable pcie
NVMe SSD boot. Add nvme dev,func in devicetree and also remove
unused GPIOs programmed in Bilby.
Change-Id: I4407f82122c04b13684d4176ba5cd5a9fe03f0db
Signed-off-by: Ritul Guru <ritul.bits@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51674
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This override was added to have the SCI mapping configured if GPIO was
used as WAKE_L pin. This however didn't set up the SCI level and trigger
information, so it likely never worked as intended.
Change-Id: I44661f05c8f517ece88714c625603579731d174b
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43049
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
When GPIO_2 was configured as PAD_NF with the WAKE_L function selected
the GPIO_2 override in soc_gpio_hook called soc_route_sci that wrote the
corresponding SCI mapping register, but didn't set up the SCI level and
trigger type, so that couldn't have worked on most of the boards. The
only boards where I think this was actually tested are the google/zork
ones and they configured GPIO_2 as PAD_SCI where the GPIO mux setting is
GPIO mode instead of the WAKE_L mode, but at least the SCI was
configured correctly. The new PAD_NF_SCI macro can configure both the
right GPIO mux setting and set up the SCI configuration correctly, so
use this new macro for the GPIO_2 pin. For test purposes I also added
the corresponding GPIO_2 configuration to amd/mandolin to see if the
affected registers end up having the expected value using the HDT
debugger to look at the registers, but didn't test the wake-up
functionality, since S3 resume isn't working on amd/mandolin yet.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Suggested-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Change-Id: Ic069e46b759fb6746645faccd254263c49a892d4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51756
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The CACHE_MRC_SETTINGS option is already selected in SoC Kconfig.
BUG = N/A
TEST = Build and boot facebook FBG1701
Signed-off-by: Frans Hendriks <fhendriks@eltan.com>
Change-Id: I1c7fd5ec36726724939660bf506a45a44848f8c4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52152
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Update the ACPI name from AMDP1015 to 1002105 based on b/177971830#180.
AMDI1015 -> AMD platform with RT1015
10021015 -> AMD platform with RT1015p
Reference:
https://www.spinics.net/lists/alsa-devel/msg124694.html
BUG=b:177971830
BRANCH=firmware-zork-13434.B
TEST=emerge-zork coreboot chromeos-bootimage, then verify with ALC1015 AMP
Signed-off-by: Frank Wu <frank_wu@compal.corp-partner.google.com>
Change-Id: Id8f378ad6f3328d7db949ecdb609a2f16acd3884
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52127
Reviewed-by: Kangheui Won <khwon@chromium.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
We seperate the EoTp packet extra data. So need to reduce the delta.
BUG=b:173603645
BRANCH=kukui
TEST=Display is normal on Kukui
Signed-off-by: Jitao Shi <jitao.shi@mediatek.com>
Change-Id: I0666068cfb04b78eb706278814163f050da32b9c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51432
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
|
|
This change hooks up the new gpio operations in DNV-NS.
Change-Id: I2179e641153da7230467c5766e4ded58fdb90292
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48618
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This commit includes makefile cleanup to exclude common source file
compilation in each stage by using all-y flag.
BUG=b:182963902
TEST=trogdor validated on limozeen
Change-Id: I48464567974a0729c1c6b6157bcce4fac39a8b38
Signed-off-by: T Michael Turney <mturney@codeaurora.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51758
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Shelley Chen <shchen@google.com>
|
|
PS/2 keyboard used IRQ 1.
BUG=none
TEST=Boot guybrush and see internal keyboard working
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I97b7382eac28aae2cc82f430c58cf8066b9701e1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52143
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Guybrush doesn't have a PS/2 mouse.
BUG=none
TEST=boot guybrush to the OS
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I87e51d23b69cfd6ad7bb88b364714d679e92728f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52145
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This register is used for masking/unmasking eSPI IRQs.
BUG=none
TEST=Build guybrush
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: Ia209539b2e0ce390e227757b16c2969b9124a845
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52142
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Rob Barnes <robbarnes@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
To train PCIe devices, the devices need to be enabled and taken out of
reset. This patch does the bare minimum needed to train PCIe. It is
not intended to handle timings, which will be addressed later.
Copy the enables for WWAN & WLAN into early GPIO Init so that they're
enabled before FSP-M runs and trains the PCIe busses.
Again, this patch is the minimum to let the FSP train the PCIe busses.
BUG=b:182202136
TEST=Boot guybrush from NVME.
Signed-off-by: Martin Roth <martinroth@chromium.org>
Change-Id: I3807e02de1e9ae40b0a4162217afd6aabb5b04ed
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52115
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This option's value is not used anywhere. Remove it.
Change-Id: I0f30cddd30d459f48b51f377b111bbc04709c5f8
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52102
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
|
|
It is zero for all mainboards. If one really wanted to ignore VT-d
support, a user-visible Kconfig option would be a better approach.
Change-Id: I320c10317f3fabee5443c16ebdf1ffd0e24193b8
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52101
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
|
|
Commit 0591348833f730a42e74039d8e2d957ec94a39d5 introduced this Kconfig
option inside soc/intel/common scope. However, it was only hooked up in
commit d74cd60b8159c3928dba318e6387f200ff3bb0e7 for Alder Lake, and in
commit 99157c1f4a80556462ca22a4ade87b2c8d09e674 for Tiger Lake. Hook up
the `SOC_INTEL_DISABLE_IGD` Kconfig option to all other platforms which
have the `InternalGfx` UPD.
Change-Id: Icd1379a835b445a6d4b028ebde5a3e355ee5b67b
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52100
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
WFC Camera driver will control the power sequence.
Therefore, set default to low.
BUG=b:184024459
TEST=abuilds
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I7ce25b83a715a022e36289dc0abf0d39f5798eb0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52148
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Update devicetree and gpio setting of metaknight to handle pen detection.
BUG=b:180426949
TEST=Build and check behavior is expected.
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Change-Id: Ieeca20eff57b16217a13d996dca3f662911f3e5a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51709
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I50e88ac946b9d8797571f9e3d4b325db760e423f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51932
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This is a temporary workaround for a bug that breaks graphics due to
some power management issue.
Signed-off-by: Matt Papageorge <matthewpapa07@gmail.com>
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ie4c8ff8e827901112fd8b2e993898006bc133241
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52141
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
pcie_rst isn't working correctly, so use the AUX resets to reset the
PCIe devices before training.
BUG=b:182202136
TEST=See PCIe devices train & enumerate
Change-Id: I6db21c79dcbd40c7a8c3f01c60b02882a3851278
Signed-off-by: Martin Roth <martinroth@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52114
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
TEST=Worked on Matt's Majolica board.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Signed-off-by: Matt Papageorge <matthewpapa07@gmail.com>
Change-Id: I65c7e0ebf1e43fd4608d46bae8a176cfc3d0236b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51956
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I838aeda2e6c403eaa3388a6b934e7ab6b4e918e3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52045
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Signed-off-by: Matt Papageorge <matthewpapa07@gmail.com>
Change-Id: Ic8a4349315f8759c79dc6b087b2a933c307cd573
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51957
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
This patch adds the functionality to write the DXIO and DDI descriptors
to the UPD data structure to the SoC code and adds the
mainboard_get_dxio_ddi_descriptors function to each mainboard using the
Cezanne SoC that gets called to get the descriptors from the board code.
Change-Id: I1cb36addcf0202cd56ce99e610a13d6d230bc981
Signed-off-by: Matt Papageorge <matthewpapa07@gmail.com>
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51948
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
This allows coreboot to easily iterate over the descriptors.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I2ecb3b543f90b8c6a957794f0c55b0ba5c72d59d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51955
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
The UPD header files get generated as part of the FSP build process. For
the initial Cezanne development we took the Picasso UPD data structures
as a starting point. This patch replaces it with the first version of
the Cezanne-specific UPD data structures that is present in version 12
of the internal work-in-progress FSP binary drops.
The serial_port_stride UPD-M field is removed, since the information is
already given by serial_port_use_mmio. The stride is 4 bytes for the
MMIO UART case and 1 byte for the legacy I/O case.
BUG=b:182524631
TEST=NVMe works on google/guybrush when the rest of the patch train is
applied as well.
Change-Id: Idca235029bf2e68d403230d55308820cab61a6c0
Signed-off-by: Matt Papageorge <matthewpapa07@gmail.com>
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51806
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ib16f133b270c99c6e060e5bd0c156cbb03293474
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51197
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
BUG=b:182211161
TEST=builds
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I375ad38da14189de2ae2713082a80e8cdb2fe5f3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52119
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
BUG=b:182211161
TEST=builds
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: Id6c20b32ddafe415132ce70abf5381ff3aad13f7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52118
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
BUG=b:182211161
TEST=builds
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I850a3ecc8776593d97f4162e812a39991caa30ef
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52117
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
GPIOs should be configured in ramstage even if they are configured in an
earlier stage.
BUG=b:182211161
TEST=builds
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I07d5c46d6ea6dc2bc9ab265d0c01772d653884cc
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52123
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
BUG=b:182211161
TEST=builds
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I2d4ec1556ac7136c454eb025ff99aafbf49b8982
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52122
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
BUG=b:182211161
TEST=builds
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I1d28c2335b095a77285dcb261a0dffe96d129c46
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52125
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
BUG=b:182211161
TEST=builds
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I9768feaadf2423acd50a71e9a2310b4ab2d1a2a8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52124
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
Following commit de50d39, remove the `volume` entry from cmos.default.
Change-Id: Ieebafffa0d2fbf6cdd24cff4ddefe090a727cbfa
Signed-off-by: Nicola Corna <nicola@corna.info>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52027
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
On VCCin there was an oscillation which occurred just as the kernel
started (kernel starting... message). On some devices, this behavior
seems even worse. In previous platforms VCCin toggled for a few ms
and then was stable. For volteer, this happens at the same point in
time for around 40ms. However, it starts oscillating again later in
the boot sequence. Once at the root shell, it seems to oscillate
indefinitely at around 100-200Hz (very variable though). To fix this
we need to control the deep C-state voltage slew rate.We have options
for controlling the deep C-state voltage slew rate through FSP UPDs.
This patch expose the following FSP UPD interface into coreboot:
- AcousticNoiseMitigation
- FastPkgCRampDisable
- SlowSlewRate
We are setting SlowSlewRate for all volteer boards to 2 which is Fast/8.
TGL has a single VR domain(Vccin). Hence, the chip config is updated to
allow mainboards to set a single value instead of an array and FSP UPDs
are accordingly set.
BUG=b:153015585
BRANCH=firmware-volteer-13672.B
TEST= Measure the change in noise level by changing the UPD values.
Signed-off-by: Shaunak Saha <shaunak.saha@intel.com>
Change-Id: Ica7f1f29995df33bdebb1fd55169cdb36f329ff8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50870
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
From Skylake/Sunrise Point onwards, there are two BIOS_CNTL registers:
one on the LPC/eSPI PCI device, and another on the SPI PCI device. When
the WPD bit changes from 0 to 1 and the LE bit is set, the PCH raises a
TCO SMI with the BIOSWR_STS bit set. However, the BIOSWR_STS bit is not
set when the TCO SMI comes from the SPI or eSPI controller instead, but
a status bit in the BIOS_CNTL register gets set. If the SMI cause is not
handled, another SMI will happen immediately after returning from the
SMI handler, which results in a deadlock.
Prevent deadlocks by clearing the SPI synchronous SMI status bit in the
SMI handler. When SPI raises a synchronous SMI, the TCO_STS bit in the
SMI_STS register is continously set until the SPI synchronous SMI status
bit is cleared. To not risk missing any other TCO SMIs, do not clear the
TCO_STS bit again in the same SMI handler invocation. If the TCO_STS bit
remains set when returning from SMM, another SMI immediately happens and
clears the TCO_STS bit, handling any pending events.
SPI can also generate asynchronous SMIs when the WPD bit is cleared and
one attempts to write to flash using SPI hardware sequencing. This patch
does not account for SPI asynchronous SMIs, because they are disabled by
default and cannot be enabled once the BIOS Interface Lock-Down bit in
the BIOS_CNTL register has been set, which coreboot already does. These
asynchronous SMIs set the SPI_STS bit of the SMI_STS register. Clearing
the SPI asynchronous SMI source should be done inside the SPI_STS SMI
handler, which is currently not implemented. All of this goes out of the
scope of this patch, and is currently not necessary anyway.
This patch does not handle eSPI because I cannot test it, and knowing if
a board uses LPC or eSPI from common code is currently not possible, and
this is beyond the scope of what this commit tries to achieve (fix SPI).
Tested on HP 280 G2, no longer deadlocks when SMM BIOS write protection
is on. Write protection will be enforced in a follow-up.
Change-Id: Iec498674ae70f6590c33a6bf4967876268f2b0c8
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50754
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This reverts commit 52e61945588bc327844acc4658426861d63ad189.
Reason for revert: Graphics actually works now. I should have abandoned this CL.
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I83aac3a2c616bb434706f23e36549760bc764080
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51985
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
TPM_INIT is disabled by default. This prevents TPM to be operational
when VBOOT is disabled.
Remove the TPM_INIT disable.
BUG=N/A
TEST=tested on facebook monolith with VBOOT disabled.
Change-Id: I84d525a18c84643903922fef0a11dcf98abbbe4d
Signed-off-by: Wim Vervoorn <wvervoorn@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52052
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
|
|
Make sure the standard for the board options are set when VBOOT is
enabled.
BUG=N/A
TEST=tested on facebook monolith
Change-Id: I9749eeeffbd26e7c5caaeb7c0407a765cf093337
Signed-off-by: Wim Vervoorn <wvervoorn@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52053
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
|
|
Added new LPC and IGD device IDs for Alderlake M.
Also, added entry for CPUID_ALDERLAKE_M_A0 in report_platform.c
TEST=Check if platform information print is coming properly in coreboot
Change-Id: If33c43da8cbd786261b00742e342f0f01622c607
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50138
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Ronak Kanabar <ronak.kanabar@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
1. Follow GT7375P Programming Guide_Rev.0.6 to increase
reset delay to 180ms.
BUG=b:181711141
TEST=Build and boot lindar to OS.
Signed-off-by: Kevin Chang <kevin.chang@lcfc.corp-partner.google.com>
Change-Id: I82222ca094eead7e9e691857e128243cfe7c310e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51739
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Zhuohao Lee <zhuohao@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Enable Bayhub SD card reader power-saving mode for Lindar and Lillipup.
BUG=b:173676531
TEST=Boot to OS and test with SD card function.
Signed-off-by: Kevin Chang <kevin.chang@lcfc.corp-partner.google.com>
Change-Id: I923d6e1beacd007c0e501f39c1f434c3e1085b9e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51623
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Zhuohao Lee <zhuohao@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
This patch changes the mem_pool implementation to track the last two
allocations (instead of just the last) and allow them both to be freed
if the mem_pool_free() calls come in in reverse order. This is intended
as a specific optimization for the CBFS cache case when a compressed
file is mapped on a platform that doesn't natively support
memory-mapping flash. In this case, cbfs_map() (chaining through to
_cbfs_alloc() with allocator == NULL) will call
mem_pool_alloc(&cbfs_cache) to allocate space for the uncompressed file
data. It will then call cbfs_load_and_decompress() to fill that
allocation, which will notice the compression and in turn call
rdev_mmap_full() to map the compressed data (which on platforms without
memory-mapped flash usually results in a second call to
mem_pool_alloc(&cbfs_cache)). It then runs the decompression algorithm
and calls rdev_munmap() on the compressed data buffer (the latter one in
the allocation sequence), leading to a mem_pool_free(). The remaining
buffer with the uncompressed data is returned out of cbfs_map() to the
caller, which should eventually call cbfs_unmap() to mem_pool_free()
that as well. This patch allows this simple case to succeed without
leaking any permanent allocations on the cache. (More complicated cases
where the caller maps other files before cbfs_unmap()ing the first one
may still lead to leaks, but those are very rare in practice.)
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: Ic5c4c56a8482752ed65e10cf35565f9b2d3e4b17
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52087
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
RETURN_FROM_VERSTAGE is a somewhat tricky construct that we don't
normally do otherwise in coreboot. While it works remarkably well in
general, new development can lead to unintentional interactions with
confusing results. This patch adds a debug print to the verstage right
before returning to the bootblock so that it's obvious this happens,
because otherwise in some cases the last printout in the verstage is
about some TPM commands which can be misleading when execution hangs
after that point.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: I9ca68a32d7a50c95d9a6948d35816fee583611bc
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52086
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
CBFS_VERIFICATION requires the CBFS metadata hash anchor to be linked
into an uncompressed stage, but for platforms using COMPRESS_BOOTBLOCK,
this is only the decompressor stage. The first CBFS accesses are made in
the bootblock stage after decompression, so if we want to make
CBFS_VERIFICATION work on those platforms, we have to pass the metadata
hash anchor from the decompressor into the bootblock. This patch does
just that. (Note that this relies on the decompressor data remaining
valid in memory for as long as the metadata hash anchor is needed. This
is always true even for OVERLAP_DECOMPRESSOR_ROMSTAGE() situations
because the FMAP and CBFS metadata necessarily need to have finished
verification before a new stage could be loaded.)
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: I2e6d7384cfb8339a24369eb6c01fc12f911c974e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52085
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
