| Age | Commit message (Collapse) | Author |
|---|
|
Add SPD support to lantis for MT53E512M32D1NP-046 WT:B
BUG=None
BRANCH=firmware-dedede-13606.B
TEST=FW_NAME=lantis emerge-dedede coreboot chromeos-bootimage
Change-Id: I22c50a55dd3b8bbda64ba1b607c8b22cc6592f98
Signed-off-by: Wisley Chen <wisley.chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56909
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
irq(ACPI_IRQ_LEVEL_LOW) -> ACPI_DESCRIPTOR_INTERRUPT -> IO-APIC,
will assert interrupt frequently;
irq_gpio(ACPI_GPIO_IRQ_EDGE_BOTH) -> ACPI_DESCRIPTOR_GPIO -> INT34C8;
will not assert interrupt frequently;
Because IRQ configuration can't be setted to both EDGE trigger.
BUG=b:195635555
BRANCH=dedede
TEST=Cirrus audio codec PLT pass
Signed-off-by: Sunwei Li <lisunwei@huaqin.corp-partner.google.com>
Change-Id: I65bca519f75af84848284f039b6ad67cb1887823
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56973
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Weimin Wu <wuweimin@huaqin.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
"Latched" GPIOs like this one are a virtual representation of the
pending interrupt flag for the edge-triggered pin and not a direct
representation of line state, so they should always be marked
ACTIVE_HIGH or depthcharge will incorrectly negate them. This has always
been wrong and meant that depthcharge doesn't correctly wait for Cr50
flow control responses on these platforms. Thankfully it doesn't seem
like we've seen any practical issues from this, but it's still very
wrong.
BRANCH=trogdor
BUG=none
TEST=Booted CoachZ (no visible difference)
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: Ie1586b0e10b64df0712e28552411c4d540a7e457
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56901
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
|
|
Setting the clock source depends on clock request pin for WLAN/SD/SSD device. Also turn off the unused (4/5/6) clock sources.
In guybrush, clock source 0/1/2/3 are routed for WLAN/SD/WWAN/SSD device.
BUG=b:186384256
BRANCH=none
TEST=Verify the config setting can update to the GPPCLKCONTROL registers.
Signed-off-by: Patrick Huang <patrick.huang@amd.corp-partner.google.com>
Change-Id: I240543e92cbc178cee034c37d7c26da0a6bbb7f6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56895
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
For mainboard devicetree, it always have definition for enabling
cpu_cluster 0 which is required for all the variants.
Since it is SoC related settings, it's better to keep in chipset.cb
as a common setting for all the mainboards using the same SoC.
BUG=None
BRANCH=None
TEST=Change has no functional impact on the brya board.
Change-Id: I20bf1a87c7a9b343a86053692617c127a1a3250d
Signed-off-by: MAULIK V VAGHELA <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56955
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
coreboot always assumes that BSP APIC ID will be 0 and core enumeration
logic will look for lapic id from the mainboard.
As per Intel 64 and IA-32 Architectures Software Developer’s Manual
Volume 3: 8.4.1 BSP and AP Processors, this assumption might
not hold true and we may have any other core as BSP. To handle this,
we need to remove hardcoding of APIC ID 0 from mainboard.
BUG=None
BRANCH=None
TEST=Check if there is no functional impact on the board.
Change-Id: I175ae26f934f08e125bea7cc3195bdb5792c2360
Signed-off-by: MAULIK V VAGHELA <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56954
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add Kconfig options and enable TPM device in devicetree
BUG=None
TEST=Booted the image and checked the successful TPM
communication in verstage,romstage & ramstage from
coreboot logs.
Signed-off-by: Thejaswani Puta thejaswani.putta@intel.com <thejaswani.putta@intel.com>
Change-Id: Icaedf9f17e35e82c35cbabd6d2938c167e42e9e8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54023
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Bora Guvendik <bora.guvendik@intel.com>
|
|
Create the driblee variant of the waddledee reference board by
copying the template files to a new directory named for the variant.
(Auto-generated by create_coreboot_variant.sh version 4.5.0.)
BUG=b:191732473
BRANCH=None
TEST=util/abuild/abuild -p none -t google/dedede -x -a
make sure the build includes GOOGLE_DRIBLEE
Signed-off-by: Frank Wu <frank_wu@compal.corp-partner.google.com>
Change-Id: I1ad9a4e0cf7999337b55d62d5cc94e4f6c2e98f3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56798
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Create the corori variant of the waddledee reference board by
copying the template files to a new directory named for the variant.
(Auto-generated by create_coreboot_variant.sh version 4.5.0.)
BUG=b:194356176
BRANCH=None
TEST=util/abuild/abuild -p none -t google/dedede -x -a
make sure the build includes GOOGLE_CORORI
Signed-off-by: Ian Feng <ian_feng@compal.corp-partner.google.com>
Change-Id: I8380d5aab61c99d545625789ff1251ec1caa84a2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56796
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
All Atlas devices have the touchscreen controller, so probing for its
presence is unnecessary. Removing the probe requirement allows the
touchscreen ACPI device in Linux to re-enumerate when rebinding its
I2C adapter device.
Without this change, after rebinding the touchscreen's I2C adapter
device using sysfs the touchscreen ACPI and HID devices are absent, and
the touchscreen is unresponsive.
With this change, the touchscreen ACPI and HID devices are re-created
after rebinding its I2C adapter device, and the touchscreen becomes
responsive again.
BUG=b:177350937
TEST=Tested on 2 Atlas DUTs running Chrome OS R94 top-of-tree builds
with Linux 4.4 and 5.4.
Built new AP FW from Atlas Chrome OS firmware branch with this change
applied. Tested shipping RO + new RW, and new RO + new RW.
Test sequence:
1) Boot DUT, verify basic touchscreen functionality.
2) $ cd /sys/bus/platform/drivers/i2c_designware
3) $ ls -ld i2c_designware.0{,/i2c-6{,/i2c-ACPI0C50:00{,/0018:0483:1058.*{,/hidraw{,/hidraw*}}}}}
lrwxrwxrwx. 1 root root 0 Aug 12 01:07 i2c_designware.0 -> ../../../../devices/pci0000:00/0000:00:15.0/i2c_designware.0
drwxr-xr-x. 5 root root 0 Aug 12 01:07 i2c_designware.0/i2c-6
drwxr-xr-x. 4 root root 0 Aug 12 01:07 i2c_designware.0/i2c-6/i2c-ACPI0C50:00
drwxr-xr-x. 5 root root 0 Aug 12 01:07 i2c_designware.0/i2c-6/i2c-ACPI0C50:00/0018:0483:1058.0002
drwxr-xr-x. 3 root root 0 Aug 12 01:07 i2c_designware.0/i2c-6/i2c-ACPI0C50:00/0018:0483:1058.0002/hidraw
drwxr-xr-x. 3 root root 0 Aug 12 01:07 i2c_designware.0/i2c-6/i2c-ACPI0C50:00/0018:0483:1058.0002/hidraw/hidraw1
4) $ echo i2c_designware.0 > unbind
5) Verify touchscreen is unresponsive (as expected after unbind).
6) $ ls -ld i2c_designware.0
ls: cannot access 'i2c_designware.0': No such file or directory
7) $ echo i2c_designware.0 > bind
*** Without this change: ***
8) Touchscreen remains unresponsive.
9) $ ls -ld i2c_designware.0{,/i2c-6{,/i2c-ACPI0C50:00}}
ls: cannot access 'i2c_designware.0/i2c-6/i2c-ACPI0C50:00': No such file or directory
lrwxrwxrwx. 1 root root 0 Aug 12 01:18 i2c_designware.0 -> ../../../../devices/pci0000:00/0000:00:15.0/i2c_designware.0
drwxr-xr-x. 4 root root 0 Aug 12 01:18 i2c_designware.0/i2c-6
*** With this change: ***
8) Touchscreen is functional again.
9) $ ls -ld i2c_designware.0{,/i2c-6{,/i2c-ACPI0C50:00{,/0018:0483:1058.*{,/hidraw{,/hidraw*}}}}}
lrwxrwxrwx. 1 root root 0 Aug 12 01:09 i2c_designware.0 -> ../../../../devices/pci0000:00/0000:00:15.0/i2c_designware.0
drwxr-xr-x. 5 root root 0 Aug 12 01:09 i2c_designware.0/i2c-6
drwxr-xr-x. 4 root root 0 Aug 12 01:09 i2c_designware.0/i2c-6/i2c-ACPI0C50:00
drwxr-xr-x. 5 root root 0 Aug 12 01:09 i2c_designware.0/i2c-6/i2c-ACPI0C50:00/0018:0483:1058.0003
drwxr-xr-x. 3 root root 0 Aug 12 01:09 i2c_designware.0/i2c-6/i2c-ACPI0C50:00/0018:0483:1058.0003/hidraw
drwxr-xr-x. 3 root root 0 Aug 12 01:09 i2c_designware.0/i2c-6/i2c-ACPI0C50:00/0018:0483:1058.0003/hidraw/hidraw1
Signed-off-by: Matthew Blecker <matthewb@chromium.org>
Change-Id: I7b90690b0591e8748d7a007f8cc9688d393e59db
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56928
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add supported memory parts in mem_parts_used.txt, and generate
SPD id for these parts.
MT53E512M32D1NP-046 WT:B
MT53E1G32D2NP-046 WT:B
BUG=b:192052098
TEST=FW_NAME=redrix emerge-brya coreboot
Signed-off-by: Wisley Chen <wisley.chen@quanta.corp-partner.google.com>
Change-Id: I61377e6cdd3af9d6d80b9e1e68191b39f43358ab
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56969
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Add I2C parameters to make sure each bus speed is around 390kHz.
BUG=b:188793264
TEST=Measure by scope.
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: Ib47228b8684c44f6acfec9e9e4b6e7b18ba6f6c0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56970
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Varshit B Pandya <varshit.b.pandya@intel.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Update initial gpio configuration for kano
BUG=b:192370253
TEST=FW_NAME=kano emerge-brya coreboot
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Change-Id: I4d6099fa8d17bebf798ddf236a68886087e2a95e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56940
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Recent change "7a8c68a: mb/google/brya: Configure H21 as GPO and A17
as low" turned EN_FCAM_PWR low since EN_FCAM_PWR is turned ON and
OFF by IPU driver while MIPI UFC probing. However USB UFC also
requires 3.3V which is enabled by A17. This caused USB UFC
enumeration to fail
BUG=b:196014678
Signed-off-by: Varshit B Pandya <varshit.b.pandya@intel.com>
Change-Id: I88c204ec07b1f7511f0d88074e336cfc9116a7d2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56882
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
modify reset_gpio as active low to meet touchscreen spec
BUG=b:195490284
BRANCH=none
TEST=build coreboot and touchscreen works
Signed-off-by: Casper Chang <casper_chang@wistron.corp-partner.google.com>
Change-Id: I7ce1b3025db8abebf5693b34da846a7e969246fb
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56923
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Enable MKBP (Matrix Keyboard Protocol) interface for all Brya family
to use for buttons and switches. Disable TBMC (Tablet Mode Switch
device), as it is not needed anymore.
BUG=b:170966461
TEST=manual test on Brya P1: Volume Up/Down buttons
Signed-off-by: Boris Mittelberg <bmbm@google.com>
Change-Id: Ic9c707f57871f388c363e01c9ab78a3b358ce728
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56903
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Add mainboard finalize and shutdown call to match zork.
Deassert EN_PWR_FP in bootblock, power up correctly in finalize.
| Phase | SOC_FP_RST_L | EN_PWR_FP | S3 resume |
|-----------|--------------|-----------|----------------------|
| Bootblock | **Low** | **Low** | Maintain High / High |
| Romstage | Low | Low | Maintain High / High |
| Ramstage | Low | **High** | Maintain High / High |
| Finalize | **High** | High | |
| Shutdown | **Low** | **Low** | |
BUG=b:191694480
TEST=Build, verify GPIO configuration.
Signed-off-by: Martin Roth <martinroth@chromium.org>
Change-Id: Iaae5feec60abb2480777d1f99174254c5132bb43
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56499
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Alder Lake SoC specific Kconfig that internally selects all eNEM
related Kconfig. CONFIG_ALDERLAKE_CAR_ENHANCED_NEM will get
autoselected if platform doesn't have INTEL_CAR_NEM Kconfig selected
explicitly.
BUG=b:168820083
TEST=Verified CONFIG_INTEL_CAR_NEM is still enable.
Change-Id: Ife1c7d2036cece4598275dfc26ed138fb46bd881
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56090
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Alder Lake onwards IA SoC to select CAR_HAS_L3_PROTECTED_WAYS from SoC
Kconfig and here is modified flow as below:
Add new MSR 0xc85 IA32_L3_PROTECTED_WAYS
Update eNEM init flow:
- Set MSR 0xC85 L3_Protected_ways = (1 << data ways) - 1
Update eNEM teardown flow:
- Set MSR 0xC85 L3_Protected_ways = 0x00000
BUG=b:168820083
TEST=Verified filling up the entire cache with memcpy at the beginning
itself and then running the entire bootblock, verstage, debug FSP-M
without running into any issue. This proves that code caching and
eviction is working as expected in eNEM mode.
Change-Id: Idb5a9ec74c50bda371c30e13aeadbb4326887fd6
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48344
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
As per TGL EDS doc:575681, two ways will be controlled with one bit
of SF QoS register(SF Mask#1/#2) hence, selects SF_MASK_2WAYS_PER_BIT
for TGL SoC.
Change-Id: Ibeef653e0c510b62880b10b3f9767664d89c9623
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56568
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
MSR IA_SF_QOS_INFO (0xc87) has been introduced since TGL and is used
to find out the NUM_SNOOP_FILTER_WAYS. Bit[5:0] of MSR 0xc87 indicates
the maximum number of bits that may be set in any of the SF MASK
register. Hence, this patch calculates SF way count using below logic:
Calculate SF masks 1:
1. Calculate SFWayCnt = (MSR 0xC87) & 0x3f
2. if CONFIG_SF_MASK_2WAYS_PER_BIT:
a. SFWayCnt = SFWayCnt / 2
3. Set SF_MASK_1 = ((1 << SFWayCnt) - 1) - SF_MASK_2
Change-Id: Ifd0b7e1a90cad4a4837adf6067fe8301dcd0a941
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51374
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
As per TGL EDS, two ways will be controlled with one bit of SF QoS
register hence, this patch introduces SF_MASK_2WAYS_PER_BIT Kconfig to
allow SoC users to select SF_MASK_2WAYS_PER_BIT to follow the EDS
recommendation.
Calculate SF masks 2:
1. if CONFIG_SF_MASK_2WAYS_PER_BIT:
a. data_ways = data_ways / 2
Also, program SF Mask#2 using below logic:
2. Set SF_MASK_2 = (1 << data_ways) - 1
Change-Id: I442bed75f13d26f357cfb32c54c5fe9efa4b474b
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56717
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Set PL4 value dynamically for brya board based on CPU SKUs
which is detectable at runtime.
BUG=b:194745919
BRANCH=None
TEST=Build FW and test on brya0 with below messages,
On brya (282):
Overriding DPTF power limits PL1 (3000, 15000) PL2 (39000, 39000) PL4 (100000)
On brya (482):
Overriding DPTF power limits PL1 (4000, 28000) PL2 (43000, 43000) PL4 (105000)
Change-Id: I20b98ccd8493ed238de647cda8ceb25f62029133
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56915
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Lockdown configuration is done in their baseboards. Thus, remove the
setting from the variants overridetree.
Change-Id: Iadb1201718466503987e4f6bd72bf711a2d3128e
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56964
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
|
|
Create the nipperkin variant of the guybrush reference board by
copying the template files to a new directory named for the variant.
(Auto-Generated by create_coreboot_variant.sh version 4.5.0.)
BUG=None
BRANCH=None
TEST=util/abuild/abuild -p none -t google/guybrush -x -a
make sure the build includes GOOGLE_NIPPERKIN
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Change-Id: Ie525ea501e6c3d5d94e67c1db1d4e307fb7ccba7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56921
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Bhanu Prakash Maiya <bhanumaiya@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Hook up microcode from 3rdparty repo for:
- TGL-U: 06-8c-01 (CPUID signature: 0x806c1)
- TGL-R: 06-8c-02 (CPUID signature: 0x806c2)
Verified microcode blob was found in CBFS on system76/darp7 (TGL-U).
CBFS: Found 'cpu_microcode_blob.bin' @0x103c0 size 0x31c00 in mcache @0x76c2d0ac
microcode: sig=0x806c1 pf=0x80 revision=0x88
coreboot reports the correct revision for the microcode.
Change-Id: I210c0133dad7ade63b9f7177aaa9a69b019469af
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56862
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add PL4 values for brya0 board for different CPU SKUs.
BUG=b:194745919
BRANCH=None
TEST=Build FW and test on brya0 with below messages,
On brya (282):
Overriding DPTF power limits PL1 (3000, 15000) PL2 (39000, 39000) PL4 (100000)
On brya (482):
Overriding DPTF power limits PL1 (4000, 28000) PL2 (43000, 43000) PL4 (105000)
Change-Id: I095e9eda6665fd1927f35ee57d52922eddd8227a
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56916
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Tune the USB phy settings to update TXVREFTUNE0/COMPDISTUNE0 to
higher value for USB port 5 (Type-A).
BUG=b:194053549
TEST= Pass USB 2.0 SI Eye diagram measurement.
Signed-off-by: Ivy Jian <ivy_jian@compal.corp-partner.google.com>
Change-Id: Id1ede34bdbee0c1f9f7d10fc7ffbc9648af31e3e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56925
Reviewed-by: Rob Barnes <robbarnes@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
DDR5 Maple Ridge SKU (Board ID 0x16) uses a Memory down DIMM
configuration.
TEST=Boot DDR5 MR SKU to OS.
Signed-off-by: Meera Ravindranath <meera.ravindranath@intel.com>
Change-Id: I0b7a96b5534d8b80776aa7578ce7c13181af7882
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56881
Reviewed-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Naming spd_info struct based on memory topology helps in reuse of
code.
lp4_lp5_spd_info -> memory_down_spd_info
ddr4_ddr5_spd_info -> dimm_module_spd_info
Signed-off-by: Meera Ravindranath <meera.ravindranath@intel.com>
Change-Id: I0b7a66b5524d8b80776ab7578ce7b13181af7882
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56899
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
|
|
Change-Id: I8c5d6686bf7c694f9d594e3801c79cfd7fb3da80
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56342
Reviewed-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Enable MKBP (Matrix Keyboard Protocol) interface for all dedede family
to use for buttons and switches. Disable TBMC (Tablet Mode Switch
device), as it is not needed anymore.
BUG=b:170966461
TEST=manual test on Madoo:
Volume Up/Down and Power buttons, Tablet Mode switch
Cq-Depend: chromium:3069163
Signed-off-by: Boris Mittelberg <bmbm@google.com>
Change-Id: I9d1f43e4dd56318af4c1d5f5c1c3a2c237a05c5f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56840
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
With current setting Display audio codec probe fails.
Hence HDMI/DP audio fails.
Earlier, with FSP 2037 was used the mode was incorrectly programmed to 4T
This setting was carried ahead with below change:
Commit : 50f8b4ebdd7db8077b87ab7686637599c9d93af3
The issue was fixed in later FSPs and with current
FSP v2237, we need to set the TMODE to 8T as per spec.
TEST=Verify HDMI/DP Playback on ADL P RVP
Fixes: 50f8b4ebdd7db8077b87ab7686637599c9d93af3
(soc/intel/alderlake: Add enum for HDA audio configuration)
Signed-off-by: Sathya Prakash M R <sathya.prakash.m.r@intel.com>
Change-Id: Ia39a33f5da2fea0dc2eaf4eae45999a711c61c33
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56208
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Balaji Manigandan <balaji.manigandan@intel.com>
Reviewed-by: Meera Ravindranath <meera.ravindranath@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Use a variable to store if the FSP should be responsible for the chipset
lockdown and use it for setting related configuration options. Thus, get
rid of that if-else-clause.
Change-Id: Ia6485bde5b33af067dfb15ca410a164e288b76b2
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52846
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
|
|
Use a variable to store if the FSP should be responsible for the chipset
lockdown and use it for setting related configuration options. Thus, get
rid of that if-else-clause.
Change-Id: I367554053f78b760ece6d59f79ce1f0e0f9fdfc6
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52845
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
|
|
Use a variable to store if the FSP should be responsible for the chipset
lockdown and use it for setting related configuration options. Thus, get
rid of that if-else-clause.
Change-Id: I0580fb3ec9daafac273dcb091f48ce403c22e8f8
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52844
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
|
|
Use a variable to store if the FSP should be responsible for the chipset
lockdown and use it for setting related configuration options. Thus, get
rid of that if-clause and adjust comments.
This changes behavior since now related options are always set,
depending on if coreboot or the FSP should be responsible for the
chipset lockdown. This ensures a defined state independent from the
default configuration of the FSP.
Change-Id: I0c43a11a40a474de4af22aa5506b1d387809bda2
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52843
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
|
|
Use a variable to store if the FSP should be responsible for the chipset
lockdown and use it for setting related configuration options. Thus, get
rid of that if-else-clause and adjust comments.
Change-Id: I202c212ec8e9ac63f5512c2e74040c23e1562b9a
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52842
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
|
|
This patch configures the SKU specific power delivery parameters for the
VR domains.
+--------------+-------+-------+-------+-------+-----------+--------+
| SKU |Setting| AC LL | DC LL |ICC MAX|TDC Current|TDC Time|
| | |(mOhms)|(mOhms)| (A) | (A) | (msec)|
+--------------+-------+-------+-------+-------+-----------+--------+
|ADL-P 682(45W)| IA | 2.3 | 2.3 | 160 | 57 | 28000 |
+ +-------+-------+-------+-------+-----------+--------+
| | GT | 3.2 | 3.2 | 50 | 57 | 28000 |
+--------------+-------+-------+-------+-------+-----------+--------+
|ADL-P 482(28W)| IA | 2.3 | 2.3 | 109 | 40 | 28000 |
+ +-------+-------+-------+-------+-----------+--------+
| | GT | 3.2 | 3.2 | 50 | 40 | 28000 |
+--------------+-------+-------+-------+-------+-----------+--------+
|ADL-P 282(15W)| IA | 2.8 | 2.8 | 80 | 20 | 28000 |
+ +-------+-------+-------+-------+-----------+--------+
| | GT | 3.2 | 3.2 | 40 | 20 | 28000 |
+--------------+-------+-------+-------+-------+-----------+--------+
These config values are generated iPDG application with ADL-P platform
package tool and supports 15W/28W/45W SKU's.
RDC Kit ID for the iPDG tools,
* Intel(R) Platform Design Studio Installer: 610905.
* Intel(R) Platform Design Studio - Platform ADL-P (Partial): 627345.
* Intel(R) Platform Design Studio - Platform ADL-P (Full): 630261.
BUG=b:195033556
Signed-off-by: V Sowmya <v.sowmya@intel.com>
Change-Id: I434fd30b5bce3bfab5a5800a30317aaa04d9926a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56325
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch updates the VccIn Aux Imon IccMax for ADL-P to SOC SKU
specific values from the FSP default value 160.
* ADL-P 682(45W) = 137.
* ADL-P 482(28W) = 128.
* ADL-P 282(15W) = 128.
These config values are generated iPDG application with ADL-P platform
package tool and supports 15W/28W/45W SKU's.
RDC Kit ID for the iPDG tools,
* Intel(R) Platform Design Studio Installer: 610905.
* Intel(R) Platform Design Studio - Platform ADL-P (Partial): 627345.
* Intel(R) Platform Design Studio - Platform ADL-P (Full): 630261.
BUG=b:195033556
Signed-off-by: V Sowmya <v.sowmya@intel.com>
Change-Id: I6c159035cba781d3661a0a0cef16f9591a583912
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56176
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch adds 4gb and 6gb dram density support to APL and GLK.
BUG=b:178665760
BRANCH=NONE
TEST=build fw and flash to the dut, the dut can boot up successfully.
Change-Id: Ic0d5d14f26a30da7a9caf4ef43d7fac88a4d2bf1
Signed-off-by: Jamie Chen <jamie.chen@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55153
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Originally we use rank_density=0 to mean disable the channel, but actually
rank_density=0 means 4Gb density in the FSP.
This patch changes the LPDDR4 enum values to the real density number and
adds a switch statement to mapping the density define in the FSP.
BUG=b:178665760
BRANCH=NONE
TEST=build fw and flash to the dut, the dut can boot up successfully.
Change-Id: I36dba2cef130211e7aea9e2a4f82c5db78f82a83
Signed-off-by: Jamie Chen <jamie.chen@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56805
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
System76 uses several custom CMOS values downstream. Reduce our diff by
providing a generic layout with the defaults:
boot_option=Fallback
debug_level=Debug
power_on_after_fail=Enable
Tested on galp3-c, gaze15, oryp5, oryp6. All boards boot multiple times
with USE_OPTION_TABLE selected.
Change-Id: Ie57b0e5713bba8ad46e1a4123a3ddd43e0eea964
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56888
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Move DFD driver to common folder so MT8195 can also use it.
BUG=b:192429713
TEST=emerge-asurada coreboot
Signed-off-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Change-Id: I7937cddf5f3a66f9269a94301d3134e6f4f9f22e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56908
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
Remove the unnecessary Vcore setting for the DVFS feature.
Signed-off-by: Ryan Chuang <ryan.chuang@mediatek.corp-partner.google.com>
Change-Id: If3c28e57a559a7ec04319c1a489138817e44ec4a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56907
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
The MEDIATEK_DRAM_DVFS_LIMIT_FREQ_CNT only makes sense if DVFS
is enabled (e.g., MEDIATEK_DRAM_DVFS) so we should change it to
depend on that instead of selecting DVFS.
Signed-off-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Change-Id: Ib81e4e48e863616ed1e36cd5c0000f4e2cfb5456
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56906
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
ALC1019 will use the ACPI compatible and share the same driver with
ALC1015. Add HID to support more compatible ICs.
BUG=b:195891240
TEST=ALC1019P driver can probe properly.
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I3e98297f3a39048b24d61e61ca95c60cd2037eb5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56877
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Add charger current throttling support for galtic
control charger index * 64 = Value mA
32*64=2048
28*64=1792
24*64=1536
20*64=1280
BUG=b:187231627
TEST=Built and tested on boten system
Cq-Depend: chrome-internal:3846209
Signed-off-by: FrankChu <frank_chu@pegatron.corp-partner.google.com>
Change-Id: I5e1849551ff051bca591f19f9e40da4c89ab74e7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54673
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Yang <paul.f.yang@intel.corp-partner.google.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
|
|
Haboki is project which use discrete TPM, so add discrete TPM and
disable cr50 in overrideree.
BUG=b:187094464
TEST=FW_NAME=haboki emerge-keeby coreboot chromeos-bootimage
Signed-off-by: Wisley Chen <wisley.chen@quanta.corp-partner.google.com>
Change-Id: I08f2a562c3f62c60402350151ea260b70890a744
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56829
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
|
|
Prevent the FSP from writing its default SVID SDID values of 8086:7270
for internal devices as this locks most of the registers. Allows the
subsystemid values set in devicetree to be used.
A description of this SSID table override behavior, along with example
code, is provided in the TigerLake FSP Integration Guide, section
15.178 ("SI_CONFIG Struct Reference").
The xHCI and HDA devices have RW/L registers rather than RW/O registers.
They can be written to multiple times but cannot be modified after
being locked, which happens during FspSiliconInit. Because coreboot
populates subsystem IDs after SiliconInit, these devices specifically
must be written beforehand or will otherwise be locked with their
default values of 0:0.
TGL also introduces parameters for customizing the default SVID:SSID.
These must be set or it will still use the FSP defaults.
Tested by checking lspci output on System76 darp7 (TGL-U).
References:
- b1fa231d76a ("soc/intel/cnl: Allow setting PCIe subsystem IDs after FSP-S")
- TigerLake FSP Integration Guide
- Intel Document #631120-001
Change-Id: I391b9fd0dc9dda925c1c8fe52bff153fe044d73e
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56867
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
|
|
Enable LTE PCIe port according to fw config.
BUG=b:192052098
TEST=emerge-brya coreboot chromeos-bootimage
Change-Id: Ic9472d2249c622858a75c63bc82e8e4e8166a3d7
Signed-off-by: Wisley Chen <wisley.chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56894
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add mipi camera support by selecting the Kconfig symbols and adding it
to the devicetree with ACPI UID 0x50000 and name IPU0.
BUG=b:192052098
TEST=checked mipi camera works
Signed-off-by: Wisley Chen <wisley.chen@quanta.corp-partner.google.com>
Change-Id: I69281f36ddbc1abf9905c8db9287500f9aa995c6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56893
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
add GPP_D16 in gimle gpio.c and set value to 1 for PP1800 DMIC init sequence
BUG=b:195968649
TEST=USE="project_gimble emerge-brya coreboot" and verify it builds
without error.
Signed-off-by: Mark Hsieh <mark_hsieh@wistron.corp-partner.google.com>
Change-Id: Ia0639162e2c3f02f622470fa16c21fe8a067cf7c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56889
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
New board introduced to trogdor family.
BUG=b:193870279
BRANCH=none
TEST=make
Change-Id: If3d9662e8725e30e1308d77b05545efbee29f846
Signed-off-by: Zanxi Chen <chenzanxi@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56384
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
Based on schematic and gpio table of taeko, generate overridetree.cb
settings for taeko.
BUG=b:195494281
TEST=FW_NAME=taeko emerge-brya coreboot chromeos-bootimage
Signed-off-by: Joey Peng <joey.peng@lcfc.corp-partner.google.com>
Change-Id: I96aaf48284a226edc39115f870bf0f3dd83ab8b4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56802
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Make use of deterministic cache helper functions from Alder Lake
SoC code to print useful information during boot as below:
Cache: Level 3: Associativity = 12 Partitions = 1 Line Size=64 Sets=16384
Cache size = 12 MiB
Change-Id: I30a56266015d69abccb885b3f230689488ee0360
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55654
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
This patch makes use of deterministic cache helper functions, for
example: cpu_get_cache_type(), cpu_get_cache_level() etc. helper
functions from arch/x86/cpu_common.c file.
Also, changed argument for get_number_of_caches() function that receives
cpu_get_max_cache_share() data directly.
Drop unused variables partitions, cache_line_size and number_of_sets as
struct cpu_cache_info.size would provide the cache size directly.
TEST=Able to dump SMBIOS Table 7 with this CL, no changes seen in output.
Getting SMBIOS data from sysfs.
SMBIOS 3.0 present.
Handle 0x0005, DMI type 7, 27 bytes
Cache Information
Socket Designation: CACHE1
Configuration: Enabled, Not Socketed, Level 1
Operational Mode: Unknown
Location: Internal
Installed Size: 288 kB
Maximum Size: 288 kB
Supported SRAM Types:
Unknown
Installed SRAM Type: Unknown
Speed: Unknown
Error Correction Type: Unknown
System Type: Data
Associativity: 12-way Set-associative
Handle 0x0006, DMI type 7, 27 bytes
Cache Information
Socket Designation: CACHE1
Configuration: Enabled, Not Socketed, Level 1
Operational Mode: Unknown
Location: Internal
Installed Size: 192 kB
Maximum Size: 192 kB
Supported SRAM Types:
Unknown
Installed SRAM Type: Unknown
Speed: Unknown
Error Correction Type: Unknown
System Type: Instruction
Associativity: 8-way Set-associative
Handle 0x0007, DMI type 7, 27 bytes
Cache Information
Socket Designation: CACHE2
Configuration: Enabled, Not Socketed, Level 2
Operational Mode: Unknown
Location: Internal
Installed Size: 1280 kB
Maximum Size: 1280 kB
Supported SRAM Types:
Unknown
Installed SRAM Type: Unknown
Speed: Unknown
Error Correction Type: Unknown
System Type: Unified
Associativity: Unknown
Handle 0x0008, DMI type 7, 27 bytes
Cache Information
Socket Designation: CACHE3
Configuration: Enabled, Not Socketed, Level 3
Operational Mode: Unknown
Location: Internal
Installed Size: 12288 kB
Maximum Size: 12288 kB
Supported SRAM Types:
Unknown
Installed SRAM Type: Unknown
Speed: Unknown
Error Correction Type: Unknown
System Type: Unified
Associativity: 12-way Set-associative
Change-Id: Iedbd3b745629dea57c3ad6b0d187eab2bcc3f7d3
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56121
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
This patch creates helper function that internally detects the CPU
type (AMD or Intel) and pick the leaf to send CPUID instruction with
different cache level to retrieve deterministic cache parameters.
Lists of helper functions generated as part of this CL :
1. cpu_check_deterministic_cache_cpuid_supported => if CPU has support
for deterministic cache using CPUID instruction.
2. cpu_get_cache_ways_assoc_info => Get cache ways for associativity.
3. cpu_get_cache_type => Get cache type.
4. cpu_get_cache_level => Get cache level.
5. cpu_get_cache_phy_partition_info => Get cache physical partitions.
6. cpu_get_cache_line_size => Get cache line size.
7. cpu_get_cache_sets => Get cache number of sets.
8. cpu_is_cache_full_assoc => Check if cache is fully associative.
9. cpu_get_max_cache_share => Cores are sharing this cache.
10. get_cache_size => Calculate the cache size.
11. fill_cpu_cache_info => Fill cpu_cache_info structure.
Change-Id: I0dd701fb47460092448b64c7fa2162f762bf3095
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55965
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
TSR2 thermal sensor doesn't define in cret. Fix DPTF passive and
critical policies for getting negative temperatures in OS.
BUG=b:195868075
BRANCH=dedede
TEST=Build and boot to OS in cret. Ensure that the DPTF entries look
correct in both static.c and SSDT tables i.e. passive and critical
policies for applicable devices only are present.
Signed-off-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Change-Id: I849662cbb3adc8e528d65af2c90e7c8e4880d607
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56870
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Add dynamic power limits selection mechanism for aldrvp board.
BUG=None
BRANCH=None
TEST=Build FW and test on adlrvp with DPTF tool
On adlrvp (282):
Overriding DPTF power limits PL1 (3000, 15000) PL2 (55000, 55000)
On adlrvp (682):
Overriding DPTF power limits PL1 (5000, 45000) PL2 (115000, 115000)
Change-Id: Id1aef0125c6e1e105665172f19bda271e232d94f
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56880
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
BUG=b:195901486, b:195387997
BRANCH=none
TEST=Check fan is able to control by EC
Signed-off-by: Scott Chao <scott_chao@wistron.corp-partner.google.com>
Change-Id: If758d75ff24c88c9eaf0de90ac0ef08d172a2edd
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56879
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Allows using the internal speakers of the oryp6.
Smart AMP data was collected using a logic analyzer connected to the IC
during system start on proprietary firmware. This data is then used to
generate a C file [1].
[1]: https://github.com/system76/smart-amp
Change-Id: I57781a7223a52b8fc5295cf686412926529c3a7f
Signed-off-by: Jeremy Soller <jeremy@system76.com>
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52417
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
For mainboard devicetree, it always have definition for enabling
cpu_cluster 0 which is required for all the variants.
Since it is SoC related settings, it's better to keep in chipset.cb
as a common setting for all the mainboards using the same SoC.
BUG=None
BRANCH=None
TEST=Change has no functional impact on the brya board.
Change-Id: I8f7c3184b62f8d84ca4605fb9f2a1cc569f1f964
Signed-off-by: MAULIK V VAGHELA <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56853
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
coreboot always assumes that BSP APIC ID will be 0 and core enumeration
logic will look for lapic id from the mainboard.
As per Intel 64 and IA-32 Architectures Software Developer’s Manual
Volume 3: 8.4.1 BSP and AP Processors, this assumption might
not hold true and we may have any other core as BSP. To handle this,
we need to remove hardcoding of APIC ID 0 from mainboard.
BUG=None
BRANCH=None
TEST=Check if there is no functional impact on the board.
Change-Id: Ibc60494b0032a3139c1e6c79251fb2da750c8de8
Signed-off-by: MAULIK V VAGHELA <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56852
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
|
|
update the DPTF parameters received from the thermal team.
BUG=b:195602767
TEST=emerge-ambassador coreboot
Signed-off-by: Kenneth Chan <kenneth.chan@quanta.corp-partner.google.com>
Change-Id: I5dc89d1d4c2b64c9aac780a7db743a91fd0ebc9b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56819
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Jeff Chase <jnchase@google.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Compatible headphone codec "Realtek ALC5682I-VD" and "cirrus CS42L42"
Compatible AMP codec "ALC1015Q-VB" and "MAX98360"
BUG=b:193373320
BRANCH=dedede
TEST=Both realtek and cirrus audio codec can work normally
Signed-off-by: Sunwei Li <lisunwei@huaqin.corp-partner.google.com>
Change-Id: I9121e75eaf46b43e6dc5ef2e31029a153c7a807d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56795
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Weimin Wu <wuweimin@huaqin.corp-partner.google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
|
|
Based on the Taeko's schematic, generate memory settings.
BUG=b:161089195
TEST=FW_NAME=taeko emerge-brya coreboot chromeos-bootimage
Signed-off-by: Joey Peng <joey.peng@lcfc.corp-partner.google.com>
Change-Id: I4e23c28aaf20d9e52b43033b4e41c751e26872bf
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56766
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
The TSR1._PSV has been redefined.
It will report errors when disassembling the ACPI tables with the iasl.
It is OK when Removing the TSR1._PSV and adding the TSR0._PSV
BUG=b:194509417
BRANCH=dedede
TEST=The iasl can run on Dut successfully
Signed-off-by: Tao Xia <xiatao5@huaqin.corp-partner.google.com>
Change-Id: I524255c79d3c71573d122944da5058389f79d95d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56828
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: Evan Green <evgreen@chromium.org>
|
|
This will enable to include multiple VBT binaries in a single image
and load corresponding file according to HW configuration.
BUG=None
TEST= Boot device on LP5/LP4, corresponding VBT file should be loaded.
Signed-off-by: Bernardo Perez Priego <bernardo.perez.priego@intel.com>
Change-Id: Iace0e5e0783b2074393a537da8cc645102d2acda
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55969
Reviewed-by: Bora Guvendik <bora.guvendik@intel.com>
Reviewed-by: Anil Kumar K <anil.kumar.k@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Keep the clock source for PCIe slots as always on. Also turn off the
unused (0/1/5/6) clock sources. Currently bilby only uses clock sources
2, 3 and 4, out of which clock source 3 and 4 are routed for PCIe
external slot. And clock source 2 is routed for M.2 PCIe slot.
TEST:Verify end devices enumerate on D:F 1.1/1.2 RPs over warm reboot.
Signed-off-by: Aamir Bohra <aamirbohra@gmail.com>
Change-Id: Ida485b06279b0a8659c8d00873c3d6023d1e542f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56826
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Update initial gpio configuration for taeko
BUG=b:195252436
TEST=FW_NAME=taeko emerge-brya coreboot
Change-Id: Ida1edbf874c93f6efac45c276920ead9311ac6f2
Signed-off-by: Joey Peng <joey.peng@lcfc.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56754
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Set power limits for brya0 variant board based on CPU SKUs
which is detectable at runtime.
BUG=b:194745919
BRANCH=None
TEST=Build FW and test on brya0 variant board with below messages,
On brya (282):
Overriding DPTF power limits PL1 (3000, 15000) PL2 (39000, 39000)
On brya (482):
Overriding DPTF power limits PL1 (4000, 28000) PL2 (43000, 43000)
Change-Id: I4c07319af756b10e5d22f320e97ff956fb4a14c6
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56622
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Enable Elan touchscreen and remove Goodix touchscreen. We also get confirmation by Elan that address is 0x15.
BUG=b:195494292
BRANCH=none
TEST=build coreboot and dmesg | grep hid, it showed i2c-ELAN9050:00.
Signed-off-by: Scott Chao <scott_chao@wistron.corp-partner.google.com>
Change-Id: I20a7fd0b370803c14990b77bab302727af197ccb
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56801
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The code is clearer when ACPI_DEVICE_SLEEP_D3_COLD is used instead of
the number 4.
Change-Id: I4b0ade1cd0b4b9cdb59f90f8d455269d0b69ed86
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56835
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
In order to support wake from D3cold, most devices require extra
circuitry and possibly out-of-band communications to the host.
Therefore, assume that most UARTs that do have wake capabilities support
wake from D3hot rather than D3cold.
BUG=b:187228954
TEST=compile
Change-Id: I24d6d0e81d980fc9c910d8f47f557c88990b6400
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56834
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
In order to support wake from D3cold, most devices require extra
circuitry and possibly out-of-band communications to the host.
Therefore, assume that most SPI peripherals that do have wake
capabilities support wake from D3hot rather than D3cold.
This also allows coreboot to expose a power resource to perform power
sequencing for a SPI peripheral that is intended to retain power in
S3/S0ix.
If support for a device with d3cold wake support is needed, it could be
added in later as an option.
BUG=b:187228954
TEST=compile
Change-Id: I1d739b49c1a43007eb0199fe39b3b7d7375e6577
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56833
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
The DA7219 does not support wake from D3cold, therefore update the
return value of _S0W from D3cold to D3hot.
BUG=b:187228954
TEST=compile
Change-Id: If03f83bb00ec90a2a6646d2c99d8bcc7e5533ac2
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56832
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Add dynamic power limits selection mechanism for brya board based on
CPU SKUs which is detectable at runtime.
BUG=b:194745919
BRANCH=None
TEST=Build FW and test on brya with below messages,
On brya (282):
Overriding DPTF power limits PL1 (3000, 15000) PL2 (39000, 39000)
On brya (482):
Overriding DPTF power limits PL1 (4000, 28000) PL2 (43000, 43000)
Change-Id: I86619516adeec13642f02ba7faf9fc4945ad774e
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56515
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
The board uses the default size specified in the SoC.
Change-Id: Ie71a0fea1ff9de6c4f1ce8db2db09bb3cd35d04d
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56865
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
|
|
coreboot always assumes that BSP APIC ID will be 0 and core enumeration
logic will look for lapic id from the mainboard.
As per Intel 64 and IA-32 Architectures Software Developer’s Manual
Volume 3: 8.4.1 BSP and AP Processors, this assumption might
not hold true and we may have any other core as BSP. To handle this,
we need to remove hardcoding of APIC ID 0 from mainboard.
BUG=None
BRANCH=None
TEST=Check if there is no functional impact on the board.
Change-Id: I726d70b4ffc35a28a654abbd20c866f1410e1aee
Signed-off-by: MAULIK V VAGHELA <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56759
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
coreboot always assumes that BSP APIC ID will always be 0 but as
per Intel 64 and IA-32 Architectures Software Developer’s Manual
Volume 3: 8.4.1 BSP and AP Processors, it says that BSP can
be any processor whose index/APIC ID might not be 0.
To handle this situation, init_cpu call is required to modify to
handle dynamic detection of APIC ID from BSP instead of hardcoding
always through devicetree. Function has been updated to create
a new node with actual BSP APIC ID when devicetree doesn't contain
APIC ID defined. In case APID ID is defined, function will use a
node with the APIC ID defined in devicetree.
Changes also requires to remove "lapic 0" hardcoding from devicetree
to allow code to fill BSP APIC ID dynamically. Otherwise coreboot
will create an extra node for CPU with APIC ID 0 and it'll show as a
extra node in kernel. This will cause kernel to report wrong (extra)
core count information then actually present.
BUG=None
BRANCH=None
TEST=Boot the JSL system and observe there is no functional impacts.
Without this CL kernel core count in `lscpu` = 3
With this CL, kernel core count is corrected to 2.
Change-Id: Ib14a5c31b3afb0d773284c684bd1994a78b94445
Signed-off-by: MAULIK V VAGHELA <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56758
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Disable reading of vdram/vddq/vmddr to reduce access of I2C
to reduce DRAM init time by about 30ms.
The values were only needed by HQA report and not needed on
production units.
BUG=b:195274787
Signed-off-by: Ryan Chuang <ryan.chuang@mediatek.corp-partner.google.com>
Change-Id: I32cd68fb8b52cec6e145d6772475fde0130ca6ac
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56850
Reviewed-by: Rex-BC Chen <rex-bc.chen@mediatek.corp-partner.google.com>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Support the config MEDIATEK_DRAM_DVFS_LIMIT_FREQ_CNT to limit DRAM
frequency counts to reduce DRAM initialization time by about 100ms.
BUG=b:195274787
Signed-off-by: Ryan Chuang <ryan.chuang@mediatek.corp-partner.google.com>
Change-Id: Ibcb9a50c24f428358ef682b64946d4c91ebd81d2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56849
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Rex-BC Chen <rex-bc.chen@mediatek.corp-partner.google.com>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
Raise little CPU to 2GHz at romstage to improve boot time by about
100 ms.
BUG=b:195274787
Signed-off-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Change-Id: Id6aac8f9db86a6c1e61ea94863f2cbde12c0482e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56844
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Rex-BC Chen <rex-bc.chen@mediatek.corp-partner.google.com>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
Add mt6359p vcore set/get support.
To adjust frequency of little core, we need to adjust voltage of vcore.
Signed-off-by: James Lo <james.lo@mediatek.corp-partner.google.com>
Change-Id: Ibf49390ba78870b834c6d0b64e3f0f30f3494f18
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56843
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Rex-BC Chen <rex-bc.chen@mediatek.corp-partner.google.com>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
Some eMMCs need 80+ms for CMD1 to complete. And the payload may need to
access eMMC in the very early stage (for example, Depthcharge needs it
20ms after started) so we have to start initialization in coreboot.
BUG=b:195274787
TEST=emerge-cherry coreboot
BRANCH=cherry
Signed-off-by: Wenbin Mei <wenbin.mei@mediatek.com>
Change-Id: Idc86f9121fa4a34f09a683f7a81087c13ea3dd42
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56842
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Rex-BC Chen <rex-bc.chen@mediatek.corp-partner.google.com>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
Select mmc storage config for cherry.
BUG=b:195274787
TEST=emerge-cherry coreboot
BRANCH=cherry
Signed-off-by: Wenbin Mei <wenbin.mei@mediatek.com>
Change-Id: I67c8795b6e6fc121e8fe61c40da05593faa02d94
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56841
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
Lulu is the only variant that does not disable channel 1 in pei_data
when the SPD index indicates it is unused. For consistency with the
other variants that use SPD files, disable channel 1 explicitly.
Change-Id: I8c613c5d90075495d2f76d33abf15d74ac63c125
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55802
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add camera support in devicetree and associated GPIO configuration.
BUG=b:193397569
BRANCH=dedede
TEST=Camera function is OK
Signed-off-by: Sunwei Li <lisunwei@huaqin.corp-partner.google.com>
Change-Id: I3275ab408f6a03735a35eaa8025c36df09c9898c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56647
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
- Chromebook have some platform need support MICMUTE and KBDILLUMTOGGLE.
- Sync ec_commands.h
This change syncs the coreboot version of google ec_commands.h with the
ec_commands.h from the google ec repository. This is a straight copy
except for the the copyright header.
BUG=b:194146863
BRANCH=none
TEST=check on evtest
type 4 (EV_MSC), code 4 (MSC_SCAN), value 9e
type 1 (EV_KEY), code 228 (KEY_KBDILLUMTOGGLE), 1
type 4 (EV_MSC), code 4 (MSC_SCAN), value 9b
type 1 (EV_KEY), code 248 (KEY_MICMUTE), value 1
Signed-off-by: Scott Chao <scott_chao@wistron.corp-partner.google.com>
Change-Id: Ie4fa3e627f448265f72279704d258b2d3fe8fc17
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56710
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Also change scan code from e02b to e01e. This is trying to fill the gaps in the standard table. The advise from Googler is using e01e for the keyboard backlight toggle key.
BUG=b:194146863
BRANCH=none
TEST=check on evtest
Signed-off-by: Scott Chao <scott_chao@wistron.corp-partner.google.com>
Change-Id: I402192ff354f30da35aec43202df9f1407911d34
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56763
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
DFD (Design for Debug) is a debugging tool, which scans
flip-flops and dumps to internal RAM on the WDT reset.
After system reboots, those values could be showed for
debugging.
Signed-off-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Change-Id: I39a4391c1d1e832d77b709f8f899bb1c6dcacd69
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56797
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
Tested on prodrive/hermes.
Change-Id: I72be8bde59d9eb0c1eff8c65dc734c6805732e09
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56086
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: <wouter.eckhardt@prodrive-technologies.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Disabling the 4 DWORD bursts causes SPI DMA operations to stall, so
leave it enabled when SPI DMA is used.
BUG=b:194919326
TEST=Build and boot to OS in Guybrush.
Change-Id: I363acdcdb4178a10e4f7eb2bbcbd6d0ca7924f2d
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56683
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jason Glenesk <jason.glenesk@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
|
|
Add a new Kconfig option to enable or disable the 4 DWORD burst support
of the SPI controller and use this setting to determine if the
corresponding feature bit in SPI100_HOST_PREF_CONFIG will be set or
cleared. Since fch_spi_disable_4dw_burst can now enable or disable the
feature, rename it to fch_spi_configure_4dw_burst. On Stoneyridge the
SPI_RD4DW_EN_HOST bit needs to be cleared (see the Rd4dw_en_host bit
definition in the SPIx2C SPI100 Host Prefetch Config register in the
public BKDG #55072 Rev 3.09), so add a SoC dependency to the Kconfig
option.
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Id754fa8d5f9554ed25cf9f3341bfdd1968693788
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56814
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jason Glenesk <jason.glenesk@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
|
|
Add a new tool that that prints elog events.
The tool, as input, accepts either a file with the RW_ELOG contents, or
if the file is not provided it reads the contents of RW_ELOG by calling
the "flashrom" tool.
The tool is based on "mosys eventlog list"[1]. For the moment it only
supports "list", but future commits will add additional functionality.
This commit also adds missing ELOG defines needed for the tool. These
defines are added with the rest of the ELOG defines, in
include/commonlib/bsd/elog.h
The tool is placed inside util/cbfstool. The rationale behind the
decision, is that this tool shares a lot in common with the other tools
located in cbfstool: vboot dependency, shared files like common.o and
valstr.o, and in spirit is similar to some of the tools located in
cbfstool/.
As an example, you call the tool like the following:
$ elogtool list -f rw_elog_dump.bin
[1]: https://chromium.googlesource.com/chromiumos/platform/mosys/+/refs/heads/main/lib/eventlog/elog.c
BUG=b:172210863
Signed-off-by: Ricardo Quesada <ricardoq@google.com>
Change-Id: Ia1fe1c9ed3c4c6bda846055d4b10943b54463935
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56406
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Jack Rosenthal <jrosenth@chromium.org>
|
|
Move ELOG defines and structs from include/elog.h to
include/comonlib/bsd/elog.h.
This is needed because the will be used from util/
(in a future commit).
It also replaces uNN types with uintNN_t types, for the reason described
above.
BUG=b:172210863
Signed-off-by: Ricardo Quesada <ricardoq@google.com>
Change-Id: I4f307f599a311810df2367b7c888f650cff1214a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56405
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jack Rosenthal <jrosenth@chromium.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
This CL adds support for new ADL-M graphics Device ID 0x46aa.
TEST=boot to OS
Signed-off-by: Bora Guvendik <bora.guvendik@intel.com>
Change-Id: Ib24b494b0eedad447f3b2a3d1d80c9941680c25d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56775
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Anil Kumar K <anil.kumar.k@intel.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
This feature was added in ADL-M RVP for discovering correct
audio topology using OEM string e.g., "ADL_MAX98373_ALC5682I_I2S"
for discovering boards having audio expansion card
Bug=None
Test= With CBI FW_CONFIG set to 0x100
localhost /home/root # dmidecode -t 11
Getting SMBIOS data from sysfs.
SMBIOS 3.0 present.
Handle 0x0009, DMI type 11, 5 bytes
OEM Strings
String 1: ADL_MAX98373_ALC5682I_I2S
Change-Id: I05887d9d654eae6d9d2da731d8ab4cf4a05c287f
Signed-off-by: Anil Kumar <anil.kumar.k@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55368
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Sathyanarayana Nujella <sathyanarayana.nujella@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Signed-off-by: Bora Guvendik <bora.guvendik@intel.com>
Change-Id: I80f11b8f0c2a1fdccbc322c3c4783c61684ff37a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55634
Reviewed-by: Selma Bensaid <selma.bensaid@intel.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
