| Age | Commit message (Collapse) | Author |
|---|
|
This patch increases the `tcc_offset` to reduce the TCC
(Thermal Control Circuit) activation temperature to avoid running
into abrupt power off during power cycle tests.
On Intel processors, the core frequency can be by an HW agent when
the current temperature reaches the TCC activation temperature.
The default TCC activation temperature is specified by MSR_IA32_TEMPERATURE_TARGET (which is 90°C for google/rex variants).
However, this patch adjusted the TCC by specifying an offset in
degrees C (i.e., using `tcc_offset` from variant override device tree).
Note: The bigger the TCC offset is, the lower the effective TCC activation temperature would be, to ensure that processors can be throttled earlier before the system critical overheats.
BUG=b:283008762
TEST=Able to perform power cycle on google/screebo w/o any crash/shutdown.
Change-Id: Ib19703877dbbfc26b2d9f538dda4f10c27cf872d
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76658
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
|
|
Hook the PchHdaSdiEnable UPD so that mainboard can change the
settings via devicetree. PchHdaSdiEnable UPD enable HDA SDI lanes.
BUG=b:268546941
TEST=Verified the settings on google/brya using debug FSP logs.
Signed-off-by: Bora Guvendik <bora.guvendik@intel.com>
Change-Id: I82bbfa5442936aefa53f8826e395b7ce75c895a3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76449
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
|
|
Adding EC_HOST_EVENT_PANIC to SCI mask allows the EC to interrupt the
Kernel when an EC panic occurs. If system safe mode is also enabled
on the EC, the kernel will have a short period to extract and save info
about the EC panic.
BUG=b:290985698
BRANCH=firmware-volteer-13672.B
TEST=Observe kernel ec panic handler run when ec panics
Change-Id: I87173f93d0e47baa816d15dad0777007342b4fdb
Signed-off-by: Rob Barnes <robbarnes@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76610
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
Choose BOARD_GOOGLE_MODEL_REX while setting up the default config value
for variants created using google/rex model.
TEST=Able to build and boot google/rex.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I107f4e375b5c9e9c0fb80c4d396164c10c1fc1e7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76657
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
|
|
This patch creates a new variant rex4es. The new variant will support ESx samples. The existing rex variant will support the QS samples.
BUG=b:290732344
TEST=Able to build google/rex4es board and boot on target hardware.
Change-Id: I25dd1f42ee812f47289da0c2ef7aa79d6f340d48
Signed-off-by: Dinesh Gehlot <digehlot@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76605
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
This patch creates a rex model so that other variants developed using
`rex` baseboard are easy to land without duplicating the config
selection.
So far, `rex0` and `rex_ec_ish` are developed using the `rex` model.
The plan is to extend the support for `rex4es` and `rex4es_ec_ish`
variants.
TEST=Able to build and boot google/rex.
Change-Id: Id4e8d1162da93b7266ee1108f870e89b6d884ab9
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76608
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Jakub Czapiga <jacz@semihalf.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
|
|
acpi.c contains architectural specific things like IOAPIC, legacy IRQ,
DMAR, HPET, ... all which require the presence of architectural headers.
Instead of littering the code with #if ENV_X86 move the functions to
different compilation units.
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Change-Id: I5083b26c0d4cc6764b4e3cb0ff586797cae7e3af
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76008
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
|
|
With arm64 -Wstack-usage= is enabled which is triggered on any use of
alloca(). Since this function basically works on x86 without wrecking
things and causing massive stack consumption it's unlikely to cause
problems on arm64.
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Change-Id: I5d445d151db5e6cc7b6e13bf74ce81007d819f1d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76007
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Tim Wawrzynczak <inforichland@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
|
|
SoC family is able to provide SoC-specific information
via amd/fsp/<soc_family>/soc_dmi_info.h.
Use common amd/fsp/common/dmi_info.h for all AMD platforms.
This way, duplicated dmi_info.h files in
vendorcode/amd/fsp/<soc_family>/ can be removed.
BUG=b:288520486
TEST=Dump `dmidecode -t 17`.
Change-Id: I5e0109af51b78360f7038b20a2975aceb721a7d5
Signed-off-by: Konrad Adamczyk <konrada@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76107
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
AGESA S3 restore needs to occur before SMM finalization/locking,
but it's a crapshoot as to which runs first since both use the same
BS_OS_RESUME/BS_ON_ENTRY boot state callback, and there's no way
to prioritize/force ordering.
To work around this, move the AGESA S3 resume call to the preceding
boot state (BS_OS_RESUME_CHECK) to ensure it runs first, and guard it
to ensure it only runs on the S3 resume path.
BUG=none
TEST=build/boot google/liara, verify S3 resume successful.
Change-Id: I765db140c6708a0b129f79fb7d3dc8a4ab3095bd
Signed-off-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76592
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
Follow baseboard Rex to make GPIO changes
BUG=b:286187821
TEST=Ability to enable and disable WIFI function in OS.
Change-Id: I805ce859c42c7c0a9d117418a80555658f844e09
Signed-off-by: Wentao Qin <qinwentao@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76551
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kun Liu <liukun11@huaqin.corp-partner.google.com>
Reviewed-by: Jakub Czapiga <jacz@semihalf.com>
|
|
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Icce4092f1e09d492e0faf4b5e85525871614d73d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76607
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
|
|
Add smn_read64 which calls smn_read32 twice to read two adjacent 32 bit
SMN registers and merges the results into a 64 bit value which it then
returns.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ib2d58ec9818559cbefd7b819ae311ad02fafa18f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76552
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
|
|
This supports a brand new I2C driver that is designed specifically
for the Pixel 2013 chromebook (LINK). The GMBus interface on the IGPU
is an i2c-compatible interface, but AFAIK only Link has touch devices
attached in this way.
On Windows, the PCIe device for the IGP is owned by the Intel
proprietary driver, hence a separate ACPI device has to be added for
the I2C driver arbitrator to attach to. The MMIO method is used instead
of _CRS so that Windows does not try to assign ownership of the
resource to our device (even though we're using the MMIO registers at
the same time as the IGP driver).
Even though in theory 2 drivers accessing the same MMIO may cause
problems, in testing, there has been no issues with
sleep/wake/hibernate, updating/installing/uninstalling the IGP driver,
or changing display resolutions with the i2c driver attached.
The arbitrator is necessary as well, since even though there are
multiple i2c buses, the MMIO registers are shared. Hence a shared lock
is required for i2c access across the buses.
The original Sleep Button devices are preserved for Linux due to the
completely custom and non-standard implementation of the Windows driver
in order to work around the non-standard nature of Link's hardware.
Change-Id: If7ee05d15bc17d335cf8c1a8e80bea62800de475
Signed-off-by: CoolStar <coolstarorganization@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76159
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
|
|
Now that we have x86 architecture specific VGA_MMIO_* defines in
arch/vga.h, use those instead of having SoC-specific defines for this.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I77b914d563bdc83e7fad7d7fccd5cf7777cb4918
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75669
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martin.roth@amd.corp-partner.google.com>
|
|
Copied from Linux kernel.
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Change-Id: I09f84e63346a270f1c7b77e8088b114800ff4864
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75923
Reviewed-by: Tim Wawrzynczak <inforichland@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
From the Linux documentation (Documentation/PCI/acpi-info.rst):
[6] PCI Firmware 3.2, sec 4.1.2:
If the operating system does not natively comprehend reserving the
MMCFG region, the MMCFG region must be reserved by firmware. The
address range reported in the MCFG table or by _CBA method (see Section
4.1.3) must be reserved by declaring a motherboard resource. For most
systems, the motherboard resource would appear at the root of the ACPI
namespace (under \_SB) in a node with a _HID of EISAID (PNP0C02), and
the resources in this case should not be claimed in the root PCI bus’s
_CRS. The resources can optionally be returned in Int15 E820 or
EFIGetMemoryMap as reserved memory but must always be reported through
ACPI as a motherboard resource.
So in order for the OS to use ECAM MMCONF over legacy PCI IO
configuration, a PNP0C02 HID device needs to reserve this region.
As no AMD platform has this defined in DSDT this fixes Linux using
legacy PCI IO configuration over MMCONF. Tianocore messes with e820
table in such a way that it prevents Linux from using PCIe ECAM. This
change fixes that problem.
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Change-Id: I852e393726a1b086cf582f4d2d707e7cde05cbf4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75729
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Sean Rhodes <sean@starlabs.systems>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
CPU:
- 2 SPR sockets
- 64 total PCIe 5.0 lanes with up to 64 lanes of Flex Bus/CXL per CPU
- Up to 32 DDR5 DIMM
- 1 Gbase-T NIC port
- 1 USB3.0 type A, 1 USB2.0 connector
- 1 VGA connector
BMC:
- ASPEED AST2600 BMC
- 1 DDR4 8Gb memory
- 1 8GB eMMC
Test:
The board boots to Linux 4.19.6 with all 192 cores available.
Change-Id: Ic9d99c3aadaa9f69e6d14d4b1a6c5157f5590684
Signed-off-by: Annie Chen <Chen.AnnieET@inventec.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75598
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Wei Chen <Chen.HW@inventec.com>
Reviewed-by: Annie Chen <chen.annieet@inventec.com>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
In order to reduce S0ix resume time, decrease stop_delay_ms from
300ms to 200ms for Goodix GT7996F. The value source is from
https://partnerissuetracker.corp.google.com/issues/285999032#comment16.
BUG=b:285999032
BRANCH=firmware-nissa-15217.B
TEST=boot uldren to ChromeOS and touchscreen is workable.
Change-Id: I2f0adadbd3d0774da03338cc0abd1639104876d9
Signed-off-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76577
Reviewed-by: Derek Huang <derekhuang@google.com>
Reviewed-by: Ian Feng <ian_feng@compal.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
There is a problem of screen shake on the old panel[1]. So increase the
panel GOP component pull-down circuit size in hardware, and update the
initialization code at the same time. The new initialization code is
mainly adjusted for GOP timing. When Display sleep in, raise all GOP
signals to VGHO and then drop to GND. In order to be consistent with
the current panel model, let's rename this file.
[1]: INX old panel product number is HJ110IZ-01A-B1, and the new
panel product number is HJ110IZ-01A-B2. We have recalled the shipment
old panel.
BUG=b:270276344
BRANCH=trogdor
TEST= test firmware display pass
Change-Id: I2b2534afee1ed700c39d3c360aafd685b63ccbfb
Signed-off-by: Cong Yang <yangcong5@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74973
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
This patch updates the Type-C USB2/3 port mapping to reflect the mux
connection change as mentioned in previous patch
commit ee3f796200bf3baf8a1906 (mb/google/rex/var/ovis: Fix mux
change as per schematics).
Here is the correct port mapping after considering the mux swap:
+--------------------------------+-------------+---------------+
| TCSS-USB Mapping | Port C0 | Port C1 | Port C2 |
+------------------+-------------+-------------+---------------+
| USB2-Port | 2 | 3 | 1 |
| USB3-Port | 0 | 2 | 1 |
+------------------+-------------+-------------+---------------+
BUG=b:289300284
TEST=Able to build and boot google/ovis to get display over Type-C1
and Type-C2 port.
Change-Id: I460004842dd8fcdc03fca6639d03e422259380ca
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76464
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Patch to increase CONSOLE_CBMEM_BUFFER_SIZE to contain FSP debug serial log.
The existing implementation uses larger cbmem size irrespective of FSP debug is enabled or
not. Ideally. larger cbmem size is required only if FSP debug is enabled.
Bug=b:284124701
TEST=Able to build and boot google/marasov.
Change-Id: I9a9e660f2738813808e0dd65d2783424b49f9a5e
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76541
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
Reduces the CAR (Cache-as-RAM) variable usage while using FSP debug binaries, which can prevent the CAR from becoming too full and unable
to integrate other CAR global variables.
This change has the following downsides:
- FSP debug output into the cbmem buffer will be partial.
To test this change, you can:
Build and boot google/rex without any function impact with non-serial
and serial FSP debug image (unless what has been documented here).
Bug=b:284124701
TEST=Able to build and boot google/rex.
Change-Id: I16a1aa25fd32327d03a37381a696c86c95014ba0
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76540
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Change SD_CLKREQ_ODL from GPP_D19 to GPP_D18
BUG=b:291051683
BRANCH=none
TEST=emerge-rex coreboot
Change-Id: Ic102e42482328580c5334e6ff036b774f5002e00
Signed-off-by: Kun Liu <liukun11@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76565
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Simon Zhou <zhouguohui@huaqin.corp-partner.google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
Add and use a define for the total number of P-state MSRs to avoid magic
constants in the code.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I37a89faa0f216790b3404fc03edc62408684cc24
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76546
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
|
|
There are 8 P-state MSRs and not only 7.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ic2899b6e454233c6cbb8fc1e439ff069c4d3d3a9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76545
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
|
|
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Change-Id: If2048c9cade731b2e4464d0670e0578f5f4bcea0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76291
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Change-Id: I2d01424731b149daa3d3378d66855ee5e074473b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76290
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
According to Intel doc#763797 to overcome early command training hang
issue, the CsPiStartHighinEct needs to be enabled for hynix memory.
BUG=b:284192689
BRANCH=firmware-brya-14505.B
TEST=Built and booted into OS.
Change-Id: Ic177c5ffcb6a3d3f76292a0d99ab0e806d43fc11
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76549
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
|
|
Enable CsPiStartHighinEct to fix MRC Cache fail issue
BUG=b:279835630
BRANCH=none
TEST=Pass MRC Cache test with toolkit 1000 times
Change-Id: I25cd856785bab9c661e30e2987b43f0dc2ba9564
Signed-off-by: Joey Peng <joey.peng@lcfc.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76544
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
According to Intel doc#763797 to overcome early command training hang
issue, the CsPiStartHighinEct needs to be enabled for hynix memory.
BUG=b:281643325
BRANCH=firmware-brya-14505.B
TEST=Built and booted into OS.
Change-Id: I95702e675fa3b73c7e8ee0c8625c7828d8129ea8
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76355
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This commit provides option for board to set CsPiStartHighinEct
FSP UPD using a new cs_pi_start_high_in_ect mb_cfg field.
BUG=b:279835630
BRANCH=none
TEST=CsPiStartHighinEct UPD is set properly
Change-Id: I7d0d5f3c782e29fb047ea421e1a5fdfc30bcc26d
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76354
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
Intel SPR supports up to 64 DIMMs on a 4 socket board.
Bump DIMM_INFO struct to 64 slots to properly present all
of them to the OS.
Change-Id: I52d77c4e9bff96adba6d265a272e0e425dbdb791
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73367
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Naresh <naresh.solanki.2011@gmail.com>
|
|
The Galago Pro 7 (galp7) is a Raptor Lake-H board.
Tested with a custom TianoCore UefiPayloadPkg.
Working:
- PS/2 keyboard
- I2C HID touchpad
- Both DIMM slots (with NMSO480E82-3200EA00)
- M.2 NVMe SSD
- All USB ports
- SD card reader
- Webcam
- Ethernet
- WiFi/Bluetooth
- Integrated graphics using Intel GOP driver
- Backlight controls on Windows 10 and Linux 6.2
- HDMI output
- DisplayPort output over USB-C
- Internal microphone
- Internal speakers
- Combined headphone + mic 3.5mm audio
- S3 suspend/resume
- Booting Pop!_OS Linux 22.04 with kernel 6.2.7
Not working:
- Detection of devices in TBT slot on boot
Change-Id: I1ae3b2c647aa75976a1ea97f7681f93eb000ba8a
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75277
Reviewed-by: Jeremy Soller <jeremy@system76.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Disable the CSME by default now that S3 is used instead of S0ix.
The CSME will not go into a low power state during S0ix when it is
disabled. This prevents the CPU from reaching C10 and so increases the
power usage during suspend compared to leaving CSME enabled. (This was
measured to be a ~2W different on TGL-U.) In S3, the state of the CSME
doesn't matter because the CPU will be off.
Change-Id: I88c0aebdcc977f3ba9dd8f46a6abfaa7a4ae8eb6
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73354
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jeremy Soller <jeremy@system76.com>
|
|
System76 EC since system76/ec@9ac513128ad9 detects if the keyboard is
white or RGB backlit via `RGBKB-DET#` at runtime. Remove the Kconfig for
the selection and update the ACPI methods for the new functionality.
Change-Id: I60d3d165a58e30d2afc8736c0eb64dd90c8227ca
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76152
Reviewed-by: Jeremy Soller <jeremy@system76.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The Darter Pro 9 (darp9) is a Raptor Lake-P board.
Tested with a custom TianoCore UefiPayloadPkg.
Working:
- PS/2 keyboard
- I2C HID touchpad
- Both DIMM slots with 5200 MT/s memory
- Both M.2 SSD slots
- All USB ports
- Webcam
- Ethernet
- WiFi/Bluetooth
- Integrated graphics using Intel GOP driver
- Internal microphone
- Internal speakers
- Combined 3.5mm headphone + mic audio
- 3.5mm microphone input
- S3 suspend/resume
- Booting Pop!_OS Linux 22.04 with kernel 6.2.7
Change-Id: If19caa90e5f90939b2946392da343b7f91f568ca
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75278
Reviewed-by: Jeremy Soller <jeremy@system76.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The Serval Workstation 13 (serw13) is a Raptor Lake-HX board.
Tested with a custom TianoCore UefiPayloadPkg.
Working:
- PS/2 Keyboard
- I2C HID touchpad
- Both DIMM slots with 5200 MT/s memory
- Both M.2 SSD slots
- All USB ports
- Webcam
- Ethernet
- WiFi/Bluetooth
- Integrated graphics using Intel GOP driver
- Internal microphone
- Internal speakers
- Combined 3.5mm headphone + mic audio output
- 3.5mm microphone input
- S3 suspend/resume
- Booting Pop!_OS Linux 22.04 with kernel 6.2.7
Not working:
- Discrete/Hybrid graphics
- Thunderbolt
Change-Id: Id709a7d06854ba9de673d5e3f25c0a1bbcc53d21
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73440
Reviewed-by: Jeremy Soller <jeremy@system76.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
After fixing TPM logs clobbering other regions in CB:73297, S3 no longer
causes cache issues resulting in power off after multiple suspends.
This is required for disabling Intel CSME by default.
Change-Id: I7eef4c883fd65db93dae81adabd895b2de90496a
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73353
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jeremy Soller <jeremy@system76.com>
|
|
The preram TPM log was being copied to the end of the CBMEM TPM log no
matter what the size of the CBMEM TPM log was. Eventually, it would
overwrite anything else in CBMEM beyond the TPM log.
This can currently be reproduced by enabling TPM_MEASURED_BOOT and
performing multiple S3 suspends, as coreboot is incorrectly performing
TPM measurements on S3 resume.
Change-Id: If76299e68eb5ed2ed20c947be35cea46c51fcdec
Signed-off-by: Jeremy Soller <jeremy@system76.com>
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73297
Reviewed-by: Martin L Roth <gaumless@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The current Sapphire Rapids code assumes that all sockets have working
CPUs. On multi-socket platforms a CPU might be missing or was disabled
due to an error. The variable PlatformData.numofIIO and the variable
SystemStatus.numCpus reflect the working CPUs, but not the actual
socket count.
Update the code to iterate over sockets until PlatformData.numofIIO
IIOs have been found. This is required as FSP doesn't sort IIOs by
working/non working status.
This resolves invalid ACPI table generation and it fixes a crash
as commands were sent to a disabled CPU.
TEST: Disabled Socket1 on IBM/SBP1.
Change-Id: I237b6392764bbdb3b96013f577a10a4394ba9c6e
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76559
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
ALC5682-VD/ALC5682I-VS load different kernel driver by different hid
name. Update hid name depending on the AUDIO_CODEC_SOURCE field of
fw_config.
ALC5682-VD: _HID = "10EC5682"
ALC5682I-VS: _HID = "RTL5682"
BUG=b:290876132
TEST=ALC5682-VD/ALC5682I-VS audio codec can work
Change-Id: Id5e0ba7a4ca57e311465ba8e74105f5ee7b8ee8a
Signed-off-by: Stanley Wu <stanley1.wu@lcfc.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76435
Reviewed-by: Derek Huang <derekhuang@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Use fw_config to separate pujjoteen5 intel wifi sar table.
BUG=b:279984381
Test=emerge-nissa coreboot
Signed-off-by: Leo Chou <leo.chou@lcfc.corp-partner.google.com>
Change-Id: I2e744bf0801bd7b18817a00fcbe3d0c62b8fc3d6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76453
Reviewed-by: Shou-Chieh Hsu <shouchieh@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Derek Huang <derekhuang@google.com>
|
|
Add an initial overridetree for gothrax based on the schematic.
BUG=b:274707912
BRANCH=None
TEST=emerge-nissa coreboot
Signed-off-by: Yunlong Jia <yunlong.jia@ecs.corp-partner.google.com>
Change-Id: Idfd9788a75f9c342f85d6e1a3d54327d64797dd8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76013
Reviewed-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Derek Huang <derekhuang@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Use the actual SocketID instead of the running index.
Change-Id: I9128909756d0dbb0c4dabc52acdc98cb2a4f7baa
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76558
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The comment is only true if all sockets have working CPUs installed.
Change-Id: I8c3376c9233c33fb770082573e07e9d96abb7855
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76557
Reviewed-by: Johnny Lin <Johnny_Lin@wiwynn.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Add a function to check if the CPU placed at the specified socket was
found usable during QPI init. This is useful for multi-socket
platforms were a CPU is missing or has been disabled due to an error.
Change-Id: I135968fcc905928b9bc6511e3ddbd7d12bad0096
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76556
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Use the FSP define to iterate over all sockets as the runtime value of
numofIIO is the detected number of sockets, not the highest working
socket.
This fixes printing the HOB on multi-socket platforms where a CPU has
been removed or has been disabled (4S system running as 3S).
Change-Id: Ieed67cd48d26c7634636c0aae6a56f3b6fbdf640
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76492
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Drivers for Pen Garage/SDCard Reader/LTE/SAR/WWAN and I2C for TPM.
BUG=b:274707912
BRANCH=None
Signed-off-by: Yunlong Jia <yunlong.jia@ecs.corp-partner.google.com>
Change-Id: I1203ca13bd55b8ab96ce5d323a36ffde06860fa9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76104
Reviewed-by: Derek Huang <derekhuang@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyle Lin <kylelinck@google.com>
|
|
On Intel Meteor Lake (MTL), PCIe CLK control register is accessed by
P2SB on IOE/SOC die.
So this patch does:
1. Enable PCIE_CLOCK_CONTROL_THROUGH_P2SB
2. Include pcie_clk.asl
3. Set the correct IOE_DIE_CLOCK_START for MTL-U/H.
BUG=b:288976547, b:289461604
TEST=Test on google/screebo and found the pcie clock is on/off properly
and sdcard PCIe port doesn't block S0ix with RTD3 cold enabled.
Change-Id: I6788ae766f36c9a0d4910fda1d6700f20ce73ea8
Signed-off-by: Kane Chen <kane.chen@intel.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76356
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
In the older platform such as Raptor Lake (RPL), Tiger Lake (TGL), it
needs PMC IPC cmd to turn on/off the corresponding clock.
Now on Meteor Lake (MTL), it control pcie clock registers on P2SB on
IOE or SoC die.
BUG=b:288976547, b:289461604
TEST=Test on google/screebo and found the pcie clock is on/off properly
and sdcard pcie port doesn't block S0ix with RTD3 cold enabled.
Change-Id: Ia729444b561daafc2dca0ed86c797eb98ce1f165
Signed-off-by: Kane Chen <kane.chen@intel.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76347
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch includes the ioe_pcr.asl file as Intel Meteor Lake has
support for IOE die.
BUG=b:290856936
TEST=Able to build and boot google/rex.
Change-Id: Ia534dbc0db5e54e173da9cdf475a7eb2bfda9e2f
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76410
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
|
|
This patch implements APIs to access PCR registers from IOE die.
BUG=b:290856936
TEST=Able to build and boot google/rex.
Change-Id: Ief7a00c4e81048f87ee308e659faeba3fde4c9cd
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76409
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
This patch introduces a new config named IOE_PCR_BASE_ADDRESS to define
P2SB base address.
BUG=b:290856936
TEST=Able to build and boot google/rex.
Change-Id: I289358f9c53b557a397bd7186e6b7419c5d8c954
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76411
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch creates a helper library to migrate all the common P2SB
access routines. The PCH P2SB ACPI implementation will now rely on the
common library to perform PCR read/write operations. This will make the
code more modular and easier to maintain.
The helper library provides a single interface for accessing P2SB
registers. This makes it easier to port the code to different platforms,
for example: adding support for PS2B belongs to the IOE die for
Meteor Lake SoC generation.
BUG=b:290856936
TEST=Able to build and boot google/rex.
Change-Id: I0b2e7ea416ca7082f68d0b822ebb9a87025b4a8b
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76408
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
- Use newer functions and avoid the * / KiB dance
- Use existing functions for figuring out TSEG and UMA
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Change-Id: I73549b23bd1bfd4009e6467a5bdfeef7de81a0cc
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76272
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Change-Id: Ib649943e13b9b319297c4be68b7039b760ebd820
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76270
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
|
|
In the JPEG decoder, use `bytes_per_line` instead of `width` for
address calculations, to allow for bigger framebuffers. When
calling jpeg_decode(), add an offset to the framebuffer address
so the picture gets centered.
Change-Id: I0174bdccfaad425e708a5fa50bcb28a1b98a23f7
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76424
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
Factor out all functions that use the indirect IO port based access to
the PM registers into a new compilation unit and only select it on
platforms that support this interface.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: If9c059e450e2137f7e05441ab89c1f0e7077be9a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76458
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
|
|
In all SoC pm_set_power_failure_state gets called either after a call to
enable_acpimmio_decode_pm04() or the ACPIMMIO mapping is already enabled
after reset on the SoC. This allows to use pm_read8 and pm_write8 that
use the ACPIMMIO mapping of the PM registers instead of pm_io_read8 and
pm_io_write8 which won't work on Phoenix and Glinda due to the IO ports
used on older generations to access to the PM registers not being
implemented any more.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Id0d0523d2c4920da41b3fb73cf62f22a60f1643a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76463
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
|
|
Use pm_io_write8 instead of open coding the same functionality.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I1d9397f2d85e48883f961adbbca0e1e71e825ce0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76462
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
|
|
Change-Id: I5c5b125ac03e07a22bcc15ad2d34c62edf74ee04
Signed-off-by: Anand Vaikar <a.vaikar2021@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76452
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
In all SoC lpc_early_init gets called either after a call to
enable_acpimmio_decode_pm04() or the ACPIMMIO mapping is already enabled
after reset on the SoC. This allows to use pm_read8 and pm_write8 that
use the ACPIMMIO mapping of the PM registers to set the PM_LPC_ENABLE
bit in the PM_LPC_GATING register instead of pm_io_read8 and
pm_io_write8 which won't work on Phoenix and Glinda due to the IO ports
used on older generations to access to the PM registers not being
implemented any more.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I8b31ec4e03a06796502c89e3c2cfaac2d41b0ed9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76461
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change i2c[0] parameter Thd:dat = 50ns;
Change i2c[1] parameter Thd:dat = 100ns;
BUG=b:287898252
BRANCH=none
TEST=Test success by EE.
Change-Id: Ibdbe4e17cf21c914b48fa6dc7d3eecf8218a2d8b
Signed-off-by: Zhongtian Wu <wuzhongtian@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76430
Reviewed-by: Kun Liu <liukun11@huaqin.corp-partner.google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
None of the platforms that used enable_acpimmio_decode_pm24 is in the
tree any more, so drop this function.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Iea345a825c4581bf2acb932692ebcad2a7a5b4ed
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76457
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
|
|
The enable_acpimmio_decode_pm04 function uses the IO port based indirect
access of the PM register space. The PM_INDEX and PM_DATA registers
don't exist any more on Glinda, so the code shouldn't access those.
Since the PM_04_ACPIMMIO_DECODE_EN bit in the
ACPIMMIO_DECODE_REGISTER_04 register is 1 after reset, the ACPIMMIO
space is still accessible.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ic6bc0479ea4ea2b9fe3629a6e15940b31b2864d3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76456
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
|
|
The enable_acpimmio_decode_pm04 function uses the IO port based indirect
access of the PM register space. The PM_INDEX and PM_DATA registers
don't exist any more on Phoenix, so the code shouldn't access those.
Since the PM_04_ACPIMMIO_DECODE_EN bit in the
ACPIMMIO_DECODE_REGISTER_04 register is 1 after reset, the ACPIMMIO
space is still accessible.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ia41f239b023edc094f5cbae63ed7c079649c74da
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76437
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch disables early EC sync to avoid an idle delay (~3sec)
without a provision to notify the user about some critical task
in progress.
Doing EC sync at later stage allows us to notify using graphical msg
on screen to make user aware of the WIP task.
BUG=b:279944831
TEST=Able to perform EC sync from depthcharge on google/rex.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I03ed40827c50e75ceaaf94e30d675014ebf22dac
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74837
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
Disable DMI link ASPM which can degrade performance of overall system.
Desktop does not need to be concerned that much about idle power
consumption.
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Change-Id: I60af9d2ab2913db449059e1e007999fa2f307f5d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69826
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change touchscreen reset_gpio GPP_C01 -> GPP_D07;
Change touchscreen enable_gpio GPP_C00 -> GPP_B17.
BUG=b:289425753
BRANCH=none
TEST=Test success by EE.
Change-Id: I7be6a2b4e87126b281f138c819d2a0a5b1af5821
Signed-off-by: Zhongtian Wu <wuzhongtian@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76429
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kun Liu <liukun11@huaqin.corp-partner.google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
Allows the new Infineon TPM chip used on Clevo laptops to be recognized.
Change-Id: I2ee31b787d80c0b9c24c748b1b28906a22a1dee7
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75807
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Create the craaskov variant of the nissa reference board by copying
the template files to a new directory named for the variant.
(Auto-Generated by create_coreboot_variant.sh version 4.5.0.)
BUG=b:290248526
BRANCH=None
TEST=util/abuild/abuild -p none -t google/brya -x -a
make sure the build includes GOOGLE_CRAASKOV
Change-Id: I1d12f7c3d0ef7067f4530c1c69c560f9a83561f6
Signed-off-by: Rex Chou <rex_chou@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76405
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Reviewed-by: Derek Huang <derekhuang@google.com>
Reviewed-by: Ian Feng <ian_feng@compal.corp-partner.google.com>
|
|
Add karis supported memory parts in mem_parts_used.txt, generate
SPD id.
1. MICRON MT62F1G32D2DS-023 WT:B
2. HYNIX H9JCNNNBK3MLYR-N6E
3. HYNIX H58G56BK8BX068
4. SAMSUNG K3KL8L80CM-MGCT
BUG=b:291018417
TEST=Use part_id_gen to generate related settings
Change-Id: I87c2c4f59454dec84d29590ee91379c9fa60ddcf
Signed-off-by: Tyler Wang <tyler.wang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76443
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: David Wu <david_wu@quanta.corp-partner.google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I01ae5a484287d2adb1516e1e4551b185b895fdde
Ref: RPL-UPH and RPL-U Refresh Platform Design Guide (#686872, rev 2.1)
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76097
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Change-Id: Id092b6dd9d42f2965801b0327a857a5a4945f793
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76288
Reviewed-by: Martin L Roth <gaumless@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add support for AP initiated mode entry. The code flow has been
optimized as below -
Code flow when AP initiated mode entry is disabled:
+-------+
| Start |
+---+---+
|
|
+---------+---------+
|wait_for_connection|
| Is DP ALT mode |
| available? |
+---------+---------+
|
+--------------->-------+
Yes| No |
+---------+---------+ |
|Skip enter_dp_mode | |
+---------+---------+ |
| |
| |
+-----------+----------+ |
|wait_for_dp_mode_entry| |
| Is DP flag set? | |
+-----------+----------+ |
| |
+--------------->--------
Yes| No |
+-----------+----------+ |
| wait_for_hpd | |
| Is HPD_LVL flag set? | |
+-----------+----------+ |
| |
+--------------->--------
Yes| No |
+-----------+----------+ |
| Rest of the code | |
+-----------+----------+ |
| |
+---------------<-------+
|
+---+---+
| End |
+-------+
Code flow when AP initiated mode entry is enabled:
+-------+
| Start |
+---+---+
|
+------------+-----------+
|Skip wait_for_connection|
+------------+-----------+
|
+--------+-------+
| enter_dp_mode |
| Is USB device? |
+--------+-------+
|
+--------------->-------+
Yes| No |
+---------+---------+ |
| enter_dp_mode | |
| Send DP mode | |
| entry command | |
+---------+---------+ |
| |
+-----------+----------+ |
|wait_for_dp_mode_entry| |
| Is DP flag set? | |
| (If not, loop wait | |
| until timed out) | |
+-----------+----------+ |
| |
+--------------->--------
Yes| No |
+-----------+----------+ |
| wait_for_hpd | |
| Is HPD_LVL flag set? | |
| (If not, loop wait | |
| until timed out) | |
+-----------+----------+ |
| |
+--------------->--------
Yes| No |
+-----------+----------+ |
| Rest of the code | |
+-----------+----------+ |
| |
+---------------<-------+
|
+---+---+
| End |
+-------+
BUG=b:247670186
TEST=Verify display over TCSS and its impact on boot time for
google/rex
Time taken by enter_dp_mode / wait_for_dp+hpd / MultiPhaseSiInit
functions with this patch train:
1. When AP Mode entry is enabled
- With type-c display on C1 and SuzyQ on C0: 6.9ms / 420ms / 616ms
- With USB key on C1 and SuzyQ on C0 : 6.0ms / 505ms / 666ms
- Without any device on C1 and SuzyQ on C0 : 3.7ms / 0ms / 178ms
2. When AP Mode entry is disabled
- With type-c display on C1 and SuzyQ on C0: 1.7ms / 2.5ms / 213ms
- With USB key on C1 and SuzyQ on C0 : 0.9ms / 3.3ms / 177ms
- Without any device on C1 and SuzyQ on C0 : 0.8ms / 1.8ms / 165ms
Without this patch train, wait_for_hpd would cause a constant delay of
WAIT_FOR_HPD_TIMEOUT_MS (i.e. 3 seconds) per type-c port when there is
no device connected.
Signed-off-by: Kapil Porwal <kapilporwal@google.com>
Change-Id: I514ccbdbaf905c49585dc00746d047554d7c7a58
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76366
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
Split wait-loop for DP and HPD flags as below -
- google_chromeec_wait_for_hpd
- google_chromeec_wait_for_dp_mode_entry
BUG=b:247670186
TEST=Verify display over TCSS and its impact on boot time for
google/rex
Signed-off-by: Kapil Porwal <kapilporwal@google.com>
Change-Id: I3e565d6134f6433930916071e94d56d92dc6cb06
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76370
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Wait for DP/HPD flags only in AP initiated mode entry
BUG=b:247670186
TEST=Verify display over TCSS and its impact on boot time for
google/rex
Signed-off-by: Kapil Porwal <kapilporwal@google.com>
Change-Id: I5137c346fbf1edabc60a53e0978e32f54885c330
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76369
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Skip TCSS `wait_for_connection` for AP initiated mode entry.
BUG=b:247670186
TEST=Verify display over TCSS and its impact on boot time for
google/rex
Signed-off-by: Kapil Porwal <kapilporwal@google.com>
Change-Id: Ia04ff470961831237fe851f7ae3feaa5623d4b4a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76368
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
Skip TCSS `enter_dp_mode` command when there is no USB device detected
on the port.
BUG=b:247670186
TEST=Verify display over TCSS and its impact on boot time for
google/rex
Signed-off-by: Kapil Porwal <kapilporwal@google.com>
Change-Id: Ie6cd84cab3631596d4d7178dae2040e25c621f63
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76352
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
Change-Id: Iad0244e798c03a26f755024453ecdd745e6286f3
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76473
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: Iafc3735b6d903a4496828189db14b09d3c4d2081
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76432
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The PRESERVE flag in the FMD file tells futility not to erase the
fmap partition when updating the firmware. Because of an issue on
myst right now, we want the RW_MRC_CACHE partition to be erased
when the firmware is updated.
BUG=b:290763369
TEST=None
Signed-off-by: Martin Roth <gaumless@gmail.com>
Change-Id: Id586ae057b2fd6d513ddbba5e1284dea39467d95
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76478
Reviewed-by: Jason Glenesk <jason.glenesk@amd.corp-partner.google.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Jon Murphy <jpmurphy@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
|
|
Phoenix doesn't have an eMMC controller and those UPDs were carried over
from Picasso. The SoC's fsp_m_params.c didn't write to any of those
fields, so this doesn't change any behavior.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ie3640c1493a92c1effba3ce42103d022bd8399ff
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76450
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
|
|
Because of the way that the CBFS filename is generated from the contents
of the microcode patch, if a duplicate microcode patch is included in
the build, the makefile would create a second copy of the name, which
doesn't work. This led to "odd" results where the other attributes of
the first copy were erased, causing cbfstool to fail. The cause of the
failure is not immediately obvious, and is a little difficult to track
down.
This patch causes an immediate failure and gives a reason as to the
cause of the issue.
When a failure is seen, this is the result:
File1: 3rdparty/amd_blobs/phoenix/psp/TypeId0x66_UcodePatch_PHXn4_A0.bin
File2: 3rdparty/amd_blobs/phoenix/psp/TypeId0x66_UcodePatch_PHX4_A0.bin
src/soc/amd/common/block/cpu/Makefile.inc:25: *** Error: The cbfs
filename "cpu_microcode_a740.bin" is used for both above files. Check
your microcode patches for duplicates.. Stop.
TEST=Now checked for both positive and negative failures.
Signed-off-by: Martin Roth <gaumless@gmail.com>
Change-Id: I3d34dc5585182545bdcbfa6370ebc34aa767cae2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76423
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Hook up microcode from 3rdparty repo for:
- 06-a5-03 (CPUID signature: 0xa0653)
- 06-a5-05 (CPUID signature: 0xa0655)
Fixes loading microcode on system76/bonw14.
Change-Id: Ie6789420926fe46fc61ea6773f02dc07dc2e9b5e
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76415
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jeremy Soller <jeremy@system76.com>
|
|
System76 boards use the VBT data file, not the VGA optionrom.
Change-Id: Ie4100e09221ae4f301a621e7aac62e38ac04a444
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76328
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jeremy Soller <jeremy@system76.com>
|
|
There is a data abort in ABL when the memory training data is used from
APOB Cache. Disable APOB Cache until the cause is identified. The
downside of this change is that the memory training happens in every
boot cycle.
BUG=b:290763369
TEST=Build BIOS image and boot to OS in Myst. Trigger a reboot from AP
console and ensure that the system boots to OS.
Change-Id: I20f4f40cdaac68bca6e121e3a238d13fe80d0d3c
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76422
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martin.roth@amd.corp-partner.google.com>
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
|
|
The dxio_port_param_type enum was copied over from Cezanne, but the enum
on the AGESA/FSP side changed between the generations. Add a TODO as a
reminder that this needs to be updated.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I8063ab00a508b045265bab73197c8ca117622800
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76448
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Use the proper dxio_link_hotplug_type enum values for the link_hotplug
field in the DXIO descriptors to replace the magic values in the code.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ieb1513737e6022a668287dc80a39d96cda2b18d5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76439
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add the dxio_link_hotplug_type enum definition for the link_hotplug
field in the DXIO descriptor struct.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ieeb3e3edaed2c689707edc4df7d25c777005fde2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76438
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
The dxio_port_param_type enum was copied over from Cezanne to Mendocino
to Phoenix, but the enum on the AGESA/FSP side changed between the
generations. Update the definition to match the definition used in the
Phoenix FSP.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I3c87fdc8bf0849d797c2af74c1d1495c7d85019f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76447
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The dxio_port_param_type enum was copied over from Cezanne to Mendocino,
but the enum on the AGESA/FSP side changed between the two generations.
Update the definition to match the definition used in the Mendocino FSP.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ie4c4d7e4e3eaf7af9a43007363135412633c7440
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76446
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
- Use newer functions and avoid the * / KiB dance
- Use existing functions for figuring out TSEG and UMA
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Change-Id: Ic6f42053b5303151906360d8512b9d63dd297854
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76249
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Change-Id: Ie585a66118c6bd1951bd004bbccbed0ee0ba9f75
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76248
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The OxPCIe952 serial cards currently fails after entering
postcar, since the state of oxpcie_present is not maintained
from previous stage.
As a quick work-around test the expected UART register space
to see if anyone decodes the address.
Change-Id: I5601034be6e413616fb3433c894fb008a3e02138
Signed-off-by: Nicholas Chin <nic.c3.14@gmail.com>
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74597
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change `CBFS_SIZE` to match the actual BIOS region size, as specified in
the FIT XML config.
Fixes building with `VALIDATE_INTEL_DESCRIPTOR` selected.
Change-Id: I91a46b3ed6cc3161df27eed19d8cdf2820e90d7e
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76326
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
It moves cr50_plat_irq_status() to common code and adds Kconfig
option to specify GPIO used for interrupt.
BUG=b:277787305
TEST=Build all affected platform and confirm using right GPIO
number. Tested on Skyrim.
Change-Id: I775c4e24cffee99b6ac3e05b58a75425029a86c8
Signed-off-by: Grzegorz Bernacki <bernacki@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75621
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
|
|
The file for Mendocino and Phoenix still used Cezanne in the comment and
from the file it's already clear to which SoC generation this belongs,
so just drop the SoC name from the comment.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I73e8b01e46904578226bb64e5e4659016c491880
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76440
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The Adder Workstation 3 (addw3) is a Raptor Lake-HX board.
Tested with a custom TianoCore UefiPayloadPkg.
Working:
- PS/2 keyboard
- I2C HID touchpad
- Both DIMM slots with 5200 MT/s memory
- Both M.2 SSD slots
- All USB ports
- Webcam
- Ethernet
- WiFi/Bluetooth
- Integrated graphics using Intel GOP driver
- Internal microphone
- Internal speakers
- Combined headphone + mic 3.5mm audio
- 3.5mm microphone input
- S3 suspend/resume
- Booting Pop!_OS Linux 22.04 with kernel 6.2.7
Not working:
- Discrete/Hybrid graphics
- Thunderbolt
Change-Id: I165a434fe18f8c0aac49cb872bb87f98551d8f2c
Signed-off-by: Jeremy Soller <jeremy@system76.com>
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73975
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
