Age | Commit message (Collapse) | Author |
|
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2901 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
This is generic PCI stuff, not nothbridge-specific in any way.
The respective #defines are already present in src/include/device/pci_def.h.
Abuild-tested, so shouldn't break anything.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2900 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Ethernet yet. The fixes are a board-specific fake spd_read_byte, cleaning up
comments, and just in general customizing for the 1c.
The lxraminit
change fixes a bug (&& used instead of ||), adds some debug prints which were
VERY useful debugging the alix1c, changes fatal error messages from print_debug
to print_emerg, and adds two functions:
banner, which just prints out a string with a banner, and
hcf, which print an emergency message and then pushes null bytes
into the uart forever, just to make sure that no bytes get lost
for any reason.
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2899 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
This board uses nearly the same devices as the BCOM Winnet100, so most of
the new code here is from the BCOM Winnet100. They differ in the IRQ routing
table only.
BTW: The AXUS board uses standard DIMM memory and can be run at 100MHz SDRAM
clock speed (it runs reliably here since month).
Signed-off-by: Juergen Beisert <juergen@kreuzholzen.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2898 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
- Add missing entry for the NIC:
device pci 0f.0 on end # Ethernet (onboard)
- Drop the following lines:
register "com1" = "{115200}"
register "com2" = "{38400}"
Those entries hardcode the BAUD rate (as far as I can tell, please
correct me if I'm wrong). We don't want that -- instead the config option
TTYS0_BAUD in Options.lb should be used(?) I verified that dropping those
lines will not break serial output (COM1, 115200, 8n1).
- Enable IDE (PCI device 00:12.2) and add the following register lines
to tell the CS5530 code to actually enable IDE channel 0:
register "ide0_enable" = "1"
register "ide1_enable" = "0" # Not available/needed on this board
Tested with a 2.5" hard drive and FILO, works fine.
- Enable USB (PCI device 00:13.0), not sure why it was commented.
- Enable COM2 as it's used by the smartcard reader.
- Add CONFIG_COMPRESSED_PAYLOAD_LZMA to Options.lb, in order to fix
abuild for this board.
- Add some more comments.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2896 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
(trivial)
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2895 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2893 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
make them const before putting them into the read-only segment...
(trivial)
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2892 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
rodata.pci_driver" warnings are coming from? We were packing those
structures into a read-only segment, but forgot to mark them const.
Despite its size, this is a fairly trivial patch created by a simple
search/replace
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2891 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2890 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2889 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2888 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
assumes a 1MB rom chip.
Hence the default position for the VGA bios should also assume a 1MB rom chip,
not a 512KB chip.
Signed-off-by: Ward Vandewege <ward@gnu.org>
Acked-by: Corey Osgood <corey.osgood@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2887 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Ward Vandewege <ward@gnu.org>
Acked-by: Ward Vandewege <ward@gnu.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2886 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Ward Vandewege <ward@gnu.org>
Acked-by: Ward Vandewege <ward@gnu.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2885 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2883 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2882 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
since it is still our most wide-spread codebase.
The patch is pretty trivial, and nobody except Torsten even looked at
it in a week, so....
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2880 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
serious issue, so I am self-acking.
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2879 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
days on a function named pll_reset that, on exit, says "Done
cpuRegInit", and which, in turn, made me think it was a lot farther
along that it was.
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2878 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
case of keyboard failure (the keyboard initialization was never hit).
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2869 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
This has not been working at all until now. With this fix, keyboard,
mouse, parallel port, and the Super I/O sensors work fine (tested
on actual hardware).
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2867 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2862 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
replacing it with a minimal, but working, framework which will be expanded.
Drop a bunch of useless and duplicated files, add missing license headers.
I'm self-acking it this time, the diff is a huge unreadable mess and the old
code is broken anyway...
This code is tested to build fine, and can boot a Linux kernel up to a
login-prompt via FILO (IDE). This is verified on actual hardware.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2859 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Joseph Smith <joe@smittys.pointclark.net>
Acked-by: Corey Osgood <corey.osgood@gmail.com>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2856 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Without this bugfix, the resource for the PCI/ISA video memory at
0xa0000 - 0xbffff is too big, i.e. it goes up to 0xcffff instead of
just 0xbffff as it should.
Here's the diff from two runs of the tool from
http://www.linuxbios.org/pipermail/linuxbios/2007-June/022449.html
on the MSI MS-7260 (K9N Neo), with and without the bugfix. After applying,
the resource size is correct again.
--- dumpres_lb_pci_vgacard_without_resfix.txt
+++ dumpres_lb_pci_vgacard_with_resfix.txt
@@ -11,7 +11,7 @@
MMIO map: #2 0x0000000000 - 0x000000ffff Access: / Dstnode:0 DstLink 0
MMIO map: #3 0x0000000000 - 0x000000ffff Access: / Dstnode:0 DstLink 0
MMIO map: #4 0x0000000000 - 0x000000ffff Access: / Dstnode:0 DstLink 0
-MMIO map: #5 0x00000a0000 - 0x00000cffff Access: R/W Dstnode:0 DstLink 0
+MMIO map: #5 0x00000a0000 - 0x00000bffff Access: R/W Dstnode:0 DstLink 0
MMIO map: #6 0x00fc000000 - 0x00fd1fffff Access: R/W Dstnode:0 DstLink 0
MMIO map: #7 0x00fd200000 - 0x00fd1fffff Access: R/W Dstnode:0 DstLink 0
MMIO map: #0 0x000000 - 0x003fff Access: R/W ISA VGA Dstnode:0 DstLink 0
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2853 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
use that feature in order to not waste RAM.
Also, add missing CONFIG_VIDEO_MB for the eaglelion/5bcm, which should
fix the build for that board.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2848 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
currently don't have it but need it to compile with the new Geode GX1
VGA support. This sets the size at 4MB, which was the size previously
defined in the VGA code.
Signed-off-by: Corey Osgood <corey.osgod@gmail.com>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2845 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2844 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
See http://www.linuxbios.org/BCOM_WINNET100_Build_Tutorial for hardware
description and build tutorials.
Signed-off-by: Juergen Beisert <juergen@kreuzholzen.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2843 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
This makes sense on systems with small memories when the VGA feature is
not used (CONFIG_VIDEO_MB = 0 in this case).
On Geode GX1 based systems the following amount of memory should be reserved
when VGA support is enabled:
- 1MiB for VGA and SVGA resolutions
- 2MiB for XGA resolution
- 4MiB for SXGA resolution
Signed-off-by: Juergen Beisert <juergen127@kreuzholzen.de>
Acked-by: Peter Stuge <peter@stuge.se>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2840 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
while I'm at it (trivial).
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2839 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Painting the splash graphic is now ifdef'ed.
Signed-off-by: Juergen Beisert <juergen127@kreuzholzen.de>
Acked-by: Peter Stuge <peter@stuge.se>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2836 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
to set up one of five screen resolutions (sorry no autodetection at runtime,
resolution is selected at buildtime) and displays a graphic in the right
bottom corner (splash screen).
Signed-off-by: Juergen Beisert <juergen127@kreuzholzen.de>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2827 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
i82801DB to reset. See this thread for more info:
http://article.gmane.org/gmane.linux.bios/26791
Signed-off-by: Joseph Smith <joe@smittys.pointclark.net>
Acked-by: Corey Osgood <corey.osgood@gmail.com>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2816 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
It is platform specific.
Signed-off-by: Marc Jones <marc.jones@amd.com>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2810 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
fixes the problems with PCI add-on cards not being detected or
initialized on MCP55-based systems (PCI bridge decoding change).
I have tested this on the MSI MS-7260 (K9N Neo) with a PCI VGA card,
which worked fine in any of the three PCI slots.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2807 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2804 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Reported by Robert Millan.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2801 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
This is tested with abuild so shouldn't break anything.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2800 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Morgan Tsai <my_tsai@sis.com>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2799 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2798 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Ward Vandewege <ward@gnu.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2797 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
assumes a 1MB rom chip.
Hence the default position for the VGA bios should also assume a 1MB rom chip, instead of a 512KB chip.
Signed-off-by: Ward Vandewege <ward@gnu.org>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2792 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Ward Vandewege <ward@gnu.org>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2787 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Ward Vandewege <ward@gnu.org>
Acked-by: Ward Vandewege <ward@gnu.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2786 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Ward Vandewege <ward@gnu.org>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2784 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
For example: in C51/MCP55 or C51/MCP51
Will allow
1. C51 at 0x10 to 0x14, and MCP at 0 to 4
2. C51 at 1 to 4, and MCP at 7 to 0x0a
The reason is c51/mcp51/mcp55 reported unitid is 0x0f (far beyond it
needed), and will prevent us from putting them on bus 0.
Typical values for c51/mcp55 or c51/mcp51:
HT_CHAIN_UNITID_BASE = 0x10 # for C51
HT_CHAIN_END_UNITID_BASE = 0 # for mcp
If only have mcp with c51,
HT_CHAIN_UNITID_BASE = 0 # for MCP
#HT_CHAIN_END_UNITID_BASE = 0 # default value 0x20
Signed-off-by: Yinghai Lu <yinghai.lu@amd.com>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2776 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
mostly undocumented, had a broken coding style, contained lots of dead
code and had several other problems, e.g. it enabled write access to the
ROM (why?), it unconditionally enabled primary/secondary IDE (which should
have a config option) and that even _twice_ (which is um... wrong).
The new code
- has 'ide0_enable' and 'ide1_enable' config options (which actually
work) to enable/disable the primary/secondary IDE interface in
Config.lb.
- Does _not_ enable write access to the ROM (or is there some good
reason to do that? If so, it should at least have a config option).
- Contains a bit more documentation.
- Uses readable (and documented) #defines instead of hardcoded magic values.
- aaand... it actually compiles ;-) Yep, that's right. The previous code
wouldn't even build, as it hadn't been fully ported from v1 (still used
v1 functions which are simply not available in v2).
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2775 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
(trivial)
Please fix this if you can.
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2774 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2773 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
(or at least most) mainboards. This should put and end to
copy-paste'ing the same file again and again for every mainboard.
Fix the build for the MSI MS-6178 target (wrong location of the common
failover.c file).
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Corey Osgood <corey.osgood@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2772 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Corey Osgood <corey.osgood@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2771 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Removed reset.c and added copyright headers.
Remove debug.c. It is not used and should not be here.
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2766 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
This is a geode LX board. There are timing settings that are not right
yet, we are still trying to get our board to boot Linux :-)
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2765 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
A trivial one-liner for the CPU I happen to have. The sales docs said it's
a "G1 revision", but the Rev F code works just fine.
Signed-off-by: Torsten Duwe <duwe@lst.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2754 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2739 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Peter Stuge <peter@stuge.se>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2738 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2735 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Generic driver for pretty much all known Standard Microsystems Corporation
(SMSC) Super I/O chips.
Most of the SMSC Super I/O chips seem to be similar enough (for our
purposes) so that we can handle them with a unified driver.
So far only the ASUS A8000 has been tested on real hardware!
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Corey Osgood <corey.osgood@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2734 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
(SMSC) Super I/O chips.
Most of the SMSC Super I/O chips seem to be similar enough (for our
purposes) so that we can handle them with a unified driver.
So far only the ASUS A8000 has been tested on real hardware!
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Corey Osgood <corey.osgood@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2733 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Now uses CAR.
New code for SPD-less memory implementation.
Updated IRQ routing.
Signed-off-by: Marc Jones <marc.jones@amd.com>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2728 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2727 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Marc Jones <marc.jones@amd.com>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2726 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
the system boot to a command line.
This patch comments out the code to set up the vga framebuffer to allow
the system to boot, without this fix the system hangs during elfboot.
The only line that is absolutely necessary to change is the SMRAM setup,
however I've commented out all vga setup to make it very obvious to both
the kernel/payload and anyone looking at the code that vga isn't
currently working. This setup might also be better handled in
northbridge.c, if it doesn't need to be done before ram init, yet
another reason to comment it all. In the future, LinuxBIOS needs to be
told that the graphics memory area, 1mb or 512kb (at the user or
developer's option), is reserved for the onchip vga, but I'm not sure if
it's taken at the top or bottom of the memory, yet. LB may also need to
set a base address for the AGP aperture and/or be told that range is
reserved as well, whether this was originally the job of the system bios
or vga bios is still a mystery. It also corrects the number of entries
in irq_tables.c, without this fix the kernel would probably complain and
hang due to unmapped IRQs.
Signed-off-by: Corey Osgood <corey.osgood@gmail.com>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2725 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2724 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
more than just one way. This version should be (more) correct.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2723 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
should only shift the mask one bit, not two.
Signed-off-by: Marc Jones <marc.jones@amd.com>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
Acked-by: Jordan Crouse <jordan.crouse@amd.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2722 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Corey Osgood <corey.osgood@gmail.com>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2721 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Corey Osgood <corey.osgood@gmail.com>
Acked-by: Joseph Smith <joe@smittys.pointclark.net>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2720 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
southbridges, along with the Asus MEW-VM. With this, my machine attempts to
boot linux, but does so very slowly and fails during the boot process, probably
because of the irq tables.
Signed-off-by: Corey Osgood <corey.osgood@gmail.com>
Acked-by: Joseph Smith <joe@smittys.pointclark.net>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2719 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
The DB800 is the AMD LX Reference Design Kit platform.
For details see: http://www.amd.com/geodelxdb800
Signed-off-by: Marc Jones <marc.jones@amd.com>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2718 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Still hardcoded for Tyan S1846.
This slightly increases performance, but it's still pretty horrible.
Some RAM settings are causing a dramatically slow system (confirmed
by comparing memtest performance results of the proprietary BIOS
and our code). Haven't found the problem, yet.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2717 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Both are very similar, thus both use the JUKI-511P target.
Linux with patches from Juergen Beisert
(http://www.linuxbios.org/pipermail/linuxbios/2007-May/020932.html)
boots and work fine (ide, usb, ethernet, serial, keyboard and sound
work normally).
Problems:
- Filo loads a bzImage only from ide0 (ide1 doesn't work yet).
- Video doesn't work, yet.
Signed-off-by: Nikolay Petukhov <nikolay.petukhov@gmail.com>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2716 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Nikolay Petukhov <nikolay.petukhov@gmail.com>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2714 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
- Linux booted with the proprietary BIOS reports 2e.f as PS/2 mouse
in the output of 'lspnp -v'.
- The floppy on 2e.f was a typo, should have been 2e.e from the beginning.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2709 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Super I/O part was incorrect.
Also, add ide0_enable/ide1_enable variables, and enable both the
primary and secondary IDE interface per default.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2708 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2707 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
return that skipped the disable code. This patch removes the return and
fixes the UART disable code.
The problem was that the disable code was ORing bits into the Legacy_IO
MSR causing issues with the LPC SIOs init code that would manifest as a
hang because the IO would not be decoded correctly. ANDing to clear the
bits fixes the issue.
Signed-off-by: Marc Jones <marc.jones@amd.com>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2706 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2705 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Sven Kapferer <skapfere@rumms.uni-mannheim.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2704 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
In a mainboard's Config.lb file you can configure whether the primary
and/or secondary IDE interfaces shall be enabled.
Also, various fixups in the rest of the southbridge code, most notably
the early SMBus code, plus some documentation improvements.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Corey Osgood <corey_osgood@verizon.net>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2703 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
As per JEDEC, we should wait 200us until voltages and clocks are stable.
Then apply NOPs for 200 clock cycles (for simplicity we use 200us here).
All other delays are so low that we get away with just waiting 1us.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Peter Stuge <peter@stuge.se>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2702 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
- Only check the RAM from 0 - 640 KB and 768 KB - 1 MB now. That's
available on all boards, regardless of what DIMMs you use.
Tested on the Tyan S1846, works fine.
- Properly set the PAM registers to allow the region from 768 KB - 1 MB
to be used as normal RAM (required for the above).
- Document all of this properly. Add/improve other documentation, too.
- Simplify and document code in northbridge.c.
- Cosmetics and coding style.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2701 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
accessible (but not writable), so that reading/loading a payload
from that area can work (for instance).
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2700 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
It moves the complete naming functionality to
src/cpu/amd/model_fxx/processor_name.c.
The current code sets the processor name string twice for Rev. F CPUs.
In src/cpu/amd/model_fxx/model_fxx_init.c the function
amd_set_name_string_f is called first. Several lines later
init_processor_name is called which doesn't recognize newer CPUs and
actually programs incorrect values, thus overwriting the previously set
CPU name. For example, this resulted in identifying an Opteron 2218 as a
Turion processor.
This patch removes the amd_set_name_string_f function from
src/cpu/amd/model_fxx/model_fxx_init.c and adds support for Rev. F CPUs
to src/cpu/amd/model_fxx/processor_name.c as described in the Revision
Guide for AMD NPT Family 0Fh Processors, AMD Document ID 33610 Rev 3.00,
October 2006.
Signed-off-by: Sven Kapferer <skapfere@rumms.uni-mannheim.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2699 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Philipp Degler <pdegler@rumms.uni-mannheim.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2698 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
the new src/southbridge/amd/cs5536 code completely replaces it.
The Artecgroup dbe61 board currently uses it, but that is broken anyway
at the moment. A fix to use the new CS5536 code for it is being worked on.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2697 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
- Add missing IT8712F_GPIO definition.
- Add functions for entering and exiting MB PnP mode.
- Add some more device init lines to pnp_dev_info[].
Signed-off-by: Philipp Degler <pdegler@rumms.uni-mannheim.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2695 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Philipp Degler <pdegler@rumms.uni-mannheim.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2694 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2688 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Marc Jones <marc.jones@amd.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2687 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
- the Transmeta TM5800 northbridge
- the Densitron DPX114 mainboard (the only one using the TM5800)
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2685 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2684 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Ward Vandewege <ward@gnu.org>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2683 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2682 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
devices conflicting with the northbridge devices on PCI bus 0.
Signed-off-by: Yinghai Lu <yinghailu@gmail.com>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2681 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
CPU: vendor AMD device
30ff2
CPU: family 0f, model 3f, stepping 02
All I know is this makes it boot when it didn't before, YMMV.
Signed-off-by: Jeremy Jackson <jerj@coplanar.net>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2678 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2676 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2675 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|