| Age | Commit message (Collapse) | Author |
|---|
|
Switch dratini overridetree to use chipset devicetree references.
Change-Id: I9f365077291ee9fa5f4dcf8835756f4cfd6eeab4
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78554
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <ericllai@google.com>
|
|
Switch akemi overridetree to use chipset devicetree references.
Drop USB port overrides which are identical to the baseboard.
TEST=build/boot google/hatch (akemi)
Change-Id: Ic25fbe4a634f8166047107a33c9fcee764f1159a
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78552
Reviewed-by: Eric Lai <ericllai@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Introduce Kconfig choice to pick between lzma, lz4 and no compression
at all of the VBT binary.
If VBT is needed in romstage, it can be used to set VBT lz4
compression as an alternative to enabling lzma compression support.
Indeed, the extra lzma code needed to de-compress VBT undermines the
compression size reduction between lzma and lz4.
BUG=b:279173035
TEST=Verified that vbt.bin is lz4 compressed with
VBT_CBFS_COMPRESSION_LZ4 and not compressed at all with
VBT_CBFS_COMPRESSION_NONE
Change-Id: I1df6a96c2ec122f0ef8ee6a1e96ffbd621b14941
Signed-off-by: Jeremy Compostella <jeremy.compostella@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76816
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Shelley Chen <shchen@google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Eric Lai <ericllai@google.com>
|
|
POWER_STATE_OFF_AFTER_FAILURE can't be directly selected since it's a
choice, so instead set POWER_STATE_DEFAULT_ON_AFTER_FAILURE to n, as
it's functionally equivalent. This fixes the warnings generated by
the pre-commit hook Kconfig check.
It is necessary to override and set default n in the mainboard Kconfig
as it is set to default y in src/soc/intel/common/block/pmc/Kconfig.
TEST=select starlabs/starbook_adl in menuconfig and verify the default
power-on setting is S5/soft off.
Change-Id: I3ce33517dcc0af693b8db8d1de2926117ad3c16b
Signed-off-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78627
Reviewed-by: Sean Rhodes <sean@starlabs.systems>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Eric Lai <ericllai@google.com>
|
|
Add FP enable/disable based on SKU ID for Morphius. This is meant
to resolve a UMA issue with Morphius devices that had the FPMCU
populated on non-fp devices. Since the FPMCU is present, and the
firmware enables the power GPIO's based on variant, not SKU, the
devices were reporting data on fingerprint errantly.
BUG=b:258040377
TEST=Flash to Morphius, test FP.
Disable test SKU, flash on Morphius, test FP.
Change-Id: If5794a9a1b7eb3daaa4cdfd1354dfb0c688624fd
Signed-off-by: Jon Murphy <jpmurphy@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78622
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
|
|
CB:77409 corrected what the UPD `Timer8254ClkSetting` was set to; this
stopped a few boards from booting.
Selecting USE_LEGACY_8254_TIMER ensures that the previous behaviour is
maintained.
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Change-Id: Ibf898cae6c9fbaf3dc7184eee745278d9b5eade4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78504
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This is required for compliant ACPI/SMBIOS implementations on AArch64,
and can optionally be displayed to the user.
Change-Id: I7022fc3c0035208bc3fdc716fc33f6b78d8e74fc
Signed-off-by: Benjamin Doron <benjamin.doron@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78042
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
|
|
Simplify audio overrides for dalboz baseboard-based variants by using
device aliases. This prevents duplicate ACPI devices from being
generated for the ChromeEC i2s tunnel (which causes Windows to BSOD
with an ACPI_BIOS_ERROR).
TEST=build/boot Win11 on google/zork (vilboz), dump ACPI tables
and verify only one EC tunnel device in SSDT.
Change-Id: I56aa2f761843aa269620f7e8c89ae9c0f205f349
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78509
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
There is only a single i2c tunnel bus for audio from the EC, so all
attached devices need to exist under a single device attached to that
bus. This change will facilitate cleanup/simplification using device
aliases in a subsequent commit.
TEST=tested with rest of patch train
Change-Id: Ie09c682a7419868d39421574568dff1a651fa0dc
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78626
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Select SOC_AMD_COMMON_LATE_SMM_LOCKING to ensure that SMM remains
unlocked on S3 resume until after the AGESA call to s3finalrestore
has completed. If SMM is locked prior, S3 resume will fail:
[DEBUG] agesawrapper_amds3laterestore() entry
[DEBUG] Error: Can't find 57a9e200 raw data to imd
[ERROR] S3 volatile data not found
TEST=build/boot google/liara, verify S3 resume succeeds.
Change-Id: I49659b4e5aba42367d6347e705cd92492fc34a0f
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78625
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Pre-Zen SoCs like Stoneyridge call into an AGESA binary as part of S3
resume, which will fail if SMM is locked, causing the device to
(eventually) cold boot. To mitigate this, add a new Kconfig to enable
"late" SMM locking, which restores the previous behavior prior to
commit 43ed5d253422 ("cpu/amd: Move locking SMM as part of SMM init").
TEST=tested with rest of patch train
Change-Id: I9971814415271a6a107c327523a0a7c188a91df6
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78352
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Move all security patch level (SPL) related Kconfig options to the
common AMD PSP Kconfig file. Commit 4ab1db82bb30 ("soc/amd: rework SPL
file override and SPL fusing handling") already reworked the SPL
handling, but missed that another Kconfig option
SOC_AMD_COMMON_BLOCK_PSP_FUSE_SPL controlled if the PSP mailbox command
to update the SPL fuses was sent by the code that got added to the build
when PERFORM_SPL_FUSING was selected.
To make things less unexpected, rename PERFORM_SPL_FUSING to
SOC_AMD_COMMON_BLOCK_PSP_SPL since it actually controls if the SPL
support code is added to the build and also rename
SOC_AMD_COMMON_BLOCK_PSP_FUSE_SPL to PERFORM_SPL_FUSING. This changes
what PERFORM_SPL_FUSING will do from including the code that could do
the fusing if another option is set to being the option that controls if
the fusing mailbox command will be set. All SoCs that support SPL now
select SOC_AMD_COMMON_BLOCK_PSP_SPL in their Kconfig, which won't burn
any SPL fuses.
The logic in the Skyrim mainboard Kconfig file is reworked to select
PERFORM_SPL_FUSING for all boards on which the SPL fuses should be
updated; on Guybrush PERFORM_SPL_FUSING default is changed to y for all
variants. The option to include the code that checks the SPL fusing
conditions and allows sending the command to update the SPL fuses if the
corresponding Kconfig is set doesn't need to be added on the mainboard
level, since it's already selected at the SoC level.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I12fd8775db66f16fe632674cd67c6af483e8d4e2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78309
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
|
|
Change-Id: I72ef272e48db7683a3170e157edd0a782143e8aa
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78431
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Martin Roth <martin.roth@amd.corp-partner.google.com>
Reviewed-by: Eric Lai <ericllai@google.com>
|
|
Select ACP audio for kahlee since it's located on the GPU.
TEST: build/boot careena to Win10. Observe audio device shows up
Change-Id: I51527a1bfae3e12ce5cf1da8a3465bbc9ddfa76e
Signed-off-by: CoolStar <coolstarorganization@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78406
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Supports a brand new ACP driver for STONEY / Grunt chromebooks.
AMD's Audio CoProcessor handles i2s/tdm audio, and is located on the
GPU.
On Windows the PCIe device for the GPU is owned by the AMD proprietary
driver, hence a separate device has to be added for the ACP driver.
Fortunately since IOMMU is disabled on STONEY, the driver itself can
pull BAR5 from the GPU and use that to initialize, so no special
configuration is required in ACPI other than the ID.
Change-Id: I0e31c3b31fa9fb99578c04b79fce2d8c1d695561
Signed-off-by: CoolStar <coolstarorganization@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78430
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
BUG=b:305793886
TEST=util/abuild/abuild -p none -t google/rex -x -a -b deku
built without errors.
Signed-off-by: Eran Mitrani <mitrani@google.com>
Change-Id: I332e404e82a7980bb8ed1fb084fe957f526f81d1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78393
Reviewed-by: YH Lin <yueherngl@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jakub Czapiga <czapiga@google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
Checking to see if a the location of a static variable is NULL isn't
super useful. If the check ever fails, there are much larger issues.
Found-by: Coverity Scan #1452607
Signed-off-by: Martin Roth <gaumless@gmail.com>
Change-Id: I6d3e012542287511f61807075c998efd6d10441e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78614
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change strcpy to strncpy just to be safe.
Found-by: Coverity Scan #1446759
Signed-off-by: Martin Roth <gaumless@gmail.com>
Change-Id: I7ed094a313692806a6ab6b4226b9978647e9cb8d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78621
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
By calling get_board_settings() when board_cfg is initialized, board_cfg
is guaranteed not to be NULL, so don't check to see if it's NULL.
Found-by: Coverity Scan #1513079
Signed-off-by: Martin Roth <gaumless@gmail.com>
Change-Id: I61105be9ed71ff30efdda66d2cbfcaf54d70053f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78618
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
In order to improve the readability of the settings, use a comma
separated list to assign values to their indexes instead of repeating
the option name for each index.
Don't convert the settings for PCIe root ports as they should stay in
the devicetree at their related root ports.
Change-Id: I85f7c0ddebf88dd21e6c2603ce45f0a4fc868d51
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78600
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
In order to improve the readability of the settings, use a comma
separated list to assign values to their indexes instead of repeating
the option name for each index.
Don't convert the settings for PCIe root ports as they should stay in
the devicetree at their related root ports.
While on it, remove superfluous comments related to modified settings.
Change-Id: I67f4fdcfb59da6c594c89d7ad3ee7f2ddbbea69b
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78592
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
In order to improve the readability of the settings, use a comma
separated list to assign values to their indexes instead of repeating
the option name for each index.
Don't convert the settings for PCIe root ports as they should stay in
the devicetree at their related root ports.
Change-Id: I25b87a157e934640355442edceb0760827dc7a43
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78591
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
In order to improve the readability of the settings, use a comma
separated list to assign values to their indexes instead of repeating
the option name for each index.
Don't convert the settings for PCIe root ports as they will be moved
into the devicetree to their related root ports at some later point.
While on it, remove superfluous comments related to modified settings.
Change-Id: I19af8c6b1167af793eb18b000fd93ec409385587
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78597
Reviewed-by: Erik van den Bogaert <ebogaert@eltan.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
|
|
It's not needed to put a backslash at the end of a line for quoted
multiline values. Thus, remove it.
Change-Id: I1b83d53598ba2adeed853a96d6c2c1a21f01a9f7
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78576
Reviewed-by: Erik van den Bogaert <ebogaert@eltan.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
The Medium Time Base (MTB) value is calculated by dividing one SPD
byte by another. Return an error if the divisor is zero before using
the value for division.
Found-by: Coverity Scan #1469303
Signed-off-by: Martin Roth <gaumless@gmail.com>
Change-Id: Ic0a70291c42b5c2d21d65de92487b2dd88609983
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78613
Reviewed-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
|
|
DDR2 already had a define to specify the SPD length, but other memory
types did not. This led to the value being coded into other locations.
Unify the definition for DDR2 to DDR5 and put the value at the top of
the respective header file.
Signed-off-by: Martin Roth <gaumless@gmail.com>
Change-Id: Id13b9c5d311984d4a98b831a8746d1659724aa96
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78601
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Keith Hui <buurin@gmail.com>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
|
|
For Sandy Bridge boards with MRC raminit support, migrate as much
MRC settings to devicetree as possible, to stop mainboard code from
needlessly overwriting entire PEI data structure, so they will not
interfere with upcoming transition to one standard Haswell way of
providing SPD info to northbridge.
Some exceptions allowed are described below and in code comments.
SPD-related items are kept out of devicetree for now. They will be
migrated (with a different representation) with the Haswell SPD
transition.
google/{butterfly,link,parrot,stout} have max DDR3 frequency set in
pei_data to 1600 (2*800), but in devicetree to 666. The reason for the
difference seems to be problems with native raminit code. These are
converted into ternaries tied to CONFIG_USE_NATIVE_RAMINIT, with an
added "fix me" tag. asus/p8x7x-series also needs the same treatment,
based on testing various memory on p8z77-m hardware.
TEST=Builds on all affected boards. asus/p8z77-m still works with multiple RAM modules tested.
Change-Id: Ie349a8f400eecca3cdbc196ea0790aebe0549e39
Signed-off-by: Keith Hui <buurin@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76962
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
|
|
The macro ENV_HAS_CBMEM achieves the same as this inline function.
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Change-Id: I6d65ca51c863abe2106f794398ddd7d7d9ac4b5e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77166
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jakub Czapiga <czapiga@google.com>
|
|
psys_pmax_watts is configured in SoC node of devicetree.
Value represents Watts the PSU provides.
Zero means automatic/default configuration (not optimal).
BUG=b:289853442
TEST=Build google/rex/ovis4es target board
Change-Id: I69afa06110254f6384352c062891c0c9c0b23070
Signed-off-by: Jakub Czapiga <jacz@semihalf.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76796
Reviewed-by: Martin L Roth <gaumless@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Adjust the STT settings.
BRANCH=none
BUG=b:270112575
TEST=emerge-skyrim coreboot chromeos-bootimage
Then the thermal team has verified.
Signed-off-by: Yunlong Jia <yunlong.jia@ecs.corp-partner.google.com>
Change-Id: I1df9bbf820b5a760007dcfd7bceb21063fc24696
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78523
Reviewed-by: Tim Van Patten <timvp@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Replace all remaining numeric references to PCI devices with their
aliases in chipset.cb.
Change-Id: I636f04c06c250639867c770511095773cb0c5205
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78508
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Update the filename for the PSP_SMUFW2_SUB1_FILE to use the compressed
and signed version (.csbin) rather than the uncompression + signed
version (.sbin), in order to be consistent with the other SMU firmware
files. This will also facilitate dropping the duplicate files in an
upcoming update to the amd_blobs repo and updating the SMU files (all
of which are .csbin).
This change is actually a no-op since the .csbin and .sbin are the same
file; it appears that the .sbin file was incorrectly named when added,
and then the same file was added later with the correct extension.
TEST=build/boot google/kahlee (liara)
Change-Id: I10fa8e949ab589d315862c06b4125c902520cbbc
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78512
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Utilize the SOC_AMD_COMMON_BLOCK_GRAPHICS_ATIF to provide the Windows
driver with information on backlight settings.
TEST: Boot google/careena to Win10. Observe display brightness controls
functional after driver loads (immediately with patched driver,
30 minutes with unpatched).
Change-Id: I6792a91f26a5f6e4dc478cdde776ff749f08946f
Signed-off-by: CoolStar <coolstarorganization@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78429
Reviewed-by: Eric Lai <ericllai@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
|
|
Select the common block graphics driver for Stoneyridge.
Drop Stoney's ACPI stub for the iGPU as the device will now be
generated by the common block acpigen and put into the SSDT.
TEST=tested with rest of patch train
Change-Id: I260b964be59c1a208ff907c474243a9ace03f206
Signed-off-by: CoolStar <coolstarorganization@gmail.com>
Signed-off-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78428
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Factor out the FSP-dependent graphics init call and header into a
separate file, so that the common graphics init can be used by non-FSP
platforms (eg Stoneyridge) without any preprocessor guards.
TEST=build google/skyrim
Change-Id: Ib025ad3adec0945b4454892d78c30b4cc79e57a0
Signed-off-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78599
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
In EC versions older than 1.18, if the mirror flag was enabled, the
EC would mirror once the system reached S5.
When a mirror is successful, the system will automatically power
on, as it acts like it's been in G3. This led to machines turning on
when the intention was them to be off.
In 1.18 and later, they're installed when turning on. The result was
slower boot times when mirroring, but no unwanted powering on.
Because of this, coreboot no longer needs to power off when setting
the mirror flag.
Change-Id: I973c1ecd59f32d3353ca392769b44aadf5fcc9c3
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78200
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
|
|
Disable the GpioOverride UPD in FSP M, and comment out the Clock Request
GPIOs to ensure that coreboot doesn't touch them.
This solves behaviour that can only be described as weird:
* Devices connected to Root Ports don't initialise
* Hang seen when entering S5
* Hang when edk2 is reached
Change-Id: Idf8d2112a1c44064af73bb54fd3e1a1a429e0649
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78199
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
|
|
Default SD card interface (PCI 14.5) to off in the baseboard, and have
all variants which use it enable it in their override tree. This will
allow for simplification when moving to using the chipset devicetree
references in a later patch.
Change-Id: I6e1230045f54e0fee376f5eeeca9da4fb9d5f6c4
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78550
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Reviewed-by: Yuchen He <yuchenhe126@gmail.com>
|
|
Default I2C3 (proximity sensor) to off in baseboard, since all variants
which use one already enable it in their override tree. This allows
variants which do not use it (the majority) to drop it from their
override trees.
Change-Id: If17cb4538a7f64d019e4e28285fb8977de72252f
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78549
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Reviewed-by: Yuchen He <yuchenhe126@gmail.com>
|
|
Default I2C2 (digitizer) to off in the baseboard, since all variants
which use one already enable it in their override tree. This allows
variants which do not use it (the majority) to drop it from their
override trees.
Change-Id: Ife42a6b849278362c1951b80b7a95363e68a2541
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78548
Reviewed-by: Yuchen He <yuchenhe126@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
|
|
Default GSPI1 (fingerprint reader) to off in baseboard, since all
variants which use one already enable it in their override tree.
This allows variants which do not use it to drop it from their
override trees.
Change-Id: I07979e35b67635ceadd3906e37de177dd081d35a
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78547
Reviewed-by: Yuchen He <yuchenhe126@gmail.com>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Create an event handler for the PEWAKE# GPIO and notify the device
driver to wake up the device.
BUG=b:301150499
TEST=Compiled and tested on google/redrix:
1. Enable runtime suspend for linux mtk_t7xx driver
2. Wait for device to enter suspended state
3. Modem should be able to wake up driver, e.g. on SIM card insert/eject
The interrupts should show up under /proc/interrupts as ACPI:Event
Signed-off-by: Paweł Anikiel <panikiel@google.com>
Change-Id: I32257689da85ea71f9de781093b3ede0cfe70a0e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78297
Reviewed-by: Jakub Czapiga <czapiga@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This signal gets deasserted by the WWAN modem to reactivate the PCIe
link when in low power mode. In order to handle this efficiently, the
kernel needs to set up an interrupt.
BUG=b:301150499
TEST=Compiled and tested on google/redrix
Signed-off-by: Paweł Anikiel <panikiel@google.com>
Change-Id: I37f6836aefe4a374eaff3e4bc11358be274cf563
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78416
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
|
|
Add ACPI devices for these components so that generated LPI constraints
for them have valid device references.
TEST=tested with rest of patch train
Change-Id: I3b85fec3de8f33d338425a417cc8b0f5290a5e4f
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78520
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
Add ACPI devices for these components so that generated LPI constraints
for them have valid device references.
TEST=tested with rest of patch train
Change-Id: Ib70dc29f54d28ec1fe7b630ab3fab24bcdd08154
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78519
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
devices
When walking the devicetree to generate the list of devices and minimum
sleep states, skip any devices which have the disable or hidden flags
set. This prevents adding entries for devices which are not present,
which are hidden (and likely to not have a min sleep state entry), or
generating duplicate entries in the case of PCIe remapping.
Any of these conditions are considered invalid by Windows and will
result in a BSOD with an INTERNAL_POWER_ERROR.
TEST=tested with rest of patch train
Change-Id: I06f64a72c82b9e03dc8af18700d24b3d10b7d3a7
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78518
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
|
|
If a root port is not present but was enabled in the devicetree, mark
it disabled so that no ACPI references will be generated by any
function which walks the devicetree (eg, LPI constraints).
TEST=tested with rest of patch train
Change-Id: I52e23fb1c0148a599ed736fc294e593ebbd27860
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78517
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Users have reported audio cutting in and out when playing through the
speakers on bonw15 and oryp11. This issue originally only affected
serw13 and was fixed before upstreaming. Apply the updated HDA verb
provided by Clevo to fix speaker output on these units as well.
Change-Id: I105bf165227456593863faa9bb8c4f152e49796b
Signed-off-by: Levi Portenier <levi@system76.com>
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Tested-by: Daniel Sutton <daniel@system76.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78511
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jeremy Soller <jeremy@system76.com>
|
|
Vendor DRAM Part Name Type
MICRON MT62F512M32D2DR-031 WT:B LPD5
HYNIX H9JCNNNBK3MLYR-N6E LPD5
HYNIX H9JCNNNCP3MLYR-N6E LPD5
MICRON MT62F1G32D4DR-031 WT:B LPD5
HYNIX H9JCNNNFA5MLYR-N6E LPD5
MICRON MT62F2G32D8DR-031 WT:B LPD5
SAMSUNG K3KL6L60GM-MGCT LPD5x
MICRON MT62F1G32D2DS-026 WT:B LPD5x
SAMSUNG K3KL8L80CM-MGCT LPD5x
HYNIX H58G56BK7BX068 LPD5x
MICRON MT62F2G32D4DS-026 WT:B LPD5x
SAMSUNG K3KL9L90CM-MGCT LPD5x
HYNIX H58G66BK7BX067 LPD5x
BUG=b:304920262
TEST=Run part_id_gen tool without any errors
Change-Id: I2968c2f0b9cdd55235f9833a3d3cdb3c83b8601b
Signed-off-by: wuweimin <wuweimin@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78389
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <ericllai@google.com>
|
|
Follow thermal team request, modify tcc_offset from 20 to 10.
BUG=b:306548525
TEST=Build and verified by thermal team
Change-Id: I7537e103be4cd1196c934ca72dbd61e064aed371
Signed-off-by: Tyler Wang <tyler.wang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78490
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: David Wu <david_wu@quanta.corp-partner.google.com>
|
|
Some Type-C monitors do not immediately assert HPD. If we enter FSP-S
before HDP is asserted, display initialisation may fail. So wait for
HPD.
This is similar to commit b40c6009141e ("mainboard/hatch: Fix puff DP
output on cold boots") on puff, except we don't use
google_chromeec_wait_for_displayport() since that EC command was removed
for TCPMv2 (https://crrev.com/c/4221975). Instead we use the HPD signals
only. By waiting for any HPD signal (Type-C or HDMI), we skip waiting if
HDMI is connected, which is the same behaviour as puff and fizz.
BUG=b:303533815
BRANCH=dedede
TEST=On dexi, connect a display via a Type-C to HDMI dongle and check
the dev and recovery screens are now displayed correctly. Also check the
logs in the following cases:
Cold reboot in dev mode, Type-C to HDMI dongle:
HPD ready after 800 ms
Warm reboot in dev mode, Type-C to HDMI dongle:
HPD ready after 0 ms
Cold/warm reboot in dev mode, direct Type-C:
HPD ready after 0 ms
Cold/warm reboot in dev mode, direct HDMI:
HPD ready after 0 ms
Cold/warm reboot in dev mode, no display:
HPD not ready after 3000 ms. Abort.
Change-Id: Ib4fc071cac98a542072ffbeb6943bff4c988554c
Signed-off-by: Kenneth Chan <kenneth.chan@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78450
Reviewed-by: Sheng-Liang Pan <sheng-liang.pan@quanta.corp-partner.google.com>
Reviewed-by: Ren Kuo <ren.kuo@quanta.corp-partner.google.com>
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: David Wu <david_wu@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Update overridetree to correct FP_MCU fw_config settings.
BUG=b:299284564, b:298328847, b:299570339
TEST=emerge-brya coreboot
Change-Id: If76dd8fa3567ed01b11a6d2ba796e8c39807816c
Signed-off-by: Morris Hsu <morris-hsu@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78454
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Bob Moragues <moragues@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Update overridetree for TouchPad.
BUG=b:299284564, b:298328847, b:299570339
TEST=emerge-brya coreboot
Change-Id: I4f88fa8a34b65aaeb64746e7f02e82d9913ce21b
Signed-off-by: Morris Hsu <morris-hsu@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78455
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Bob Moragues <moragues@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Set the following register value to make SX9324 work normally
"ph0_pin" = "{1, 3, 3}"
"ph1_pin" = "{3, 2, 1}"
"ph2_pin" = "{3, 3, 1}"
"ph3_pin" = "{1, 3, 3}"
"ph01_resolution" = "512"
"ph23_resolution" = "1024"
"startup_sensor" = "1"
"ph01_proxraw_strength" = "2"
"ph23_proxraw_strength" = "2"
"avg_pos_strength" = "256"
"cs_idle_sleep" = ""gnd""
"int_comp_resistor" = ""lowest""
"input_precharge_resistor_ohms" = "4000"
"input_analog_gain" = "3"
BUG=b:295109511
BRANCH=None
TEST=emerge-nissa coreboot chromeos-bootimage & Check sar sensor data
Signed-off-by: Yunlong Jia <yunlong.jia@ecs.corp-partner.google.com>
Change-Id: Ib15f12d754fec8b379afd702b27d0701fac78072
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78463
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Derek Huang <derekhuang@google.com>
|
|
After commit e12b313844da ("drivers/pc80/rtc/option.c: Allow CMOS
defaults to extend to bank 1"), Thinkpad X200 with
CONFIG(STATIC_OPTION_TABLE) can no longer resume from s3 (detected via
bisect).
Further inspection shows that DRAM training result of GM45 is stored
in CMOS above 128 bytes in raminit_read_write_training.c, for s3 resume
to restore, but it will be erased by sanitize_cmos(), which now clears
both bank 0 and bank 1, leaving only "untrained" result restored, so s3
resume will fail.
However, resetting CMOS seems unnecessary during s3 resume. Now,
cmos_need_reset will be negated when acpi_is_wakeup_s3() returns true.
Tested: Thinkpad X200 with CONFIG(STATIC_OPTION_TABLE) can resume from
s3 again with these changes.
Change-Id: I533e83f3b95f327b0e24f4d750f8812325b7770b
Signed-off-by: Bill XIE <persmule@hardenedlinux.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78288
Reviewed-by: Jonathon Hall <jonathon.hall@puri.sm>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Use human readable properties as upstream driver support.
BUG=b:297977526
TEST=Able to get sensor values changed w/wo a hand covering the device.
before this CL , SSD.dsl of STH9324
Package (0x02)
{
"semtech,ph0-pin",
Package (0x03)
{
Zero,
Zero,
Zero
},
...
Package (0x02)
{
"semtech,ph23-resolution",
Zero
},
Package (0x02)
{
"semtech,startup-sensor",
Zero
},
....
after this CL , SSD.dsl of STH9324
Package (0x02)
{
"semtech,ph0-pin",
Package (0x03)
{
One,
0x02,
0x02
},
...
Package (0x02)
{
" semtech,ph23-resolution",
0x0400
},
Package (0x02)
{
"semtech,startup-sensor",
One
},
Change-Id: Ie0d929228f4510f33b07d9c4cfdfcd2a9a437c27
Signed-off-by: Ivy Jian <ivy.jian@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78174
Reviewed-by: Eric Lai <ericllai@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Gwendal Grignou <gwendal@chromium.org>
|
|
Clevo had apparently swapped the Realtek card reader for the O2 Micro
card reader for newer batches of all TGL models. Enable the BayHub
driver on everything (except bonw15, which doesn't have a card reader)
to fix LTR programming, as was done for other in commit 3d7a5bdf58e0
("mb/system76: Enable DRIVERS_GENERIC_BAYHUB_LV2 to fix LTR issue").
Tested on system76/galp5: CPU reaches C-states deeper than C2 when idle.
Change-Id: I3667e08acd23c12638159a2f7d2592737a34e63d
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78298
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jeremy Soller <jeremy@system76.com>
Reviewed-by: Eric Lai <ericllai@google.com>
|
|
Update Goodix touchpad HID to GDIX0000 for GXTP7288 and GXTP7863.
BUG=b:305118852
BRANCH=firmware-dedede-13606.B
TEST=Build and touchpads are workable
# evtest for GXTP7863
No device specified, trying to scan all of /dev/input/event*
Available devices:
/dev/input/event0: Lid Switch
/dev/input/event1: Power Button
/dev/input/event2: AT Translated Set 2 keyboard
/dev/input/event3: cros_ec_buttons
/dev/input/event4: Elan Touchscreen
/dev/input/event5: GDIX0000:00 27C6:0D51 Mouse
/dev/input/event6: GDIX0000:00 27C6:0D51 Touchpad
# evtest for GXTP7288
No device specified, trying to scan all of /dev/input/event*
Available devices:
/dev/input/event0: Lid Switch
/dev/input/event1: Power Button
/dev/input/event10: GDIX0000:00 27C6:01F5 Touchpad
/dev/input/event11: sof-da7219max98360a Headset Jack
/dev/input/event12: sof-da7219max98360a HDMI/DP,pcm=2
/dev/input/event13: sof-da7219max98360a HDMI/DP,pcm=3
/dev/input/event14: sof-da7219max98360a HDMI/DP,pcm=4
/dev/input/event2: AT Translated Set 2 keyboard
/dev/input/event3: cros_ec_buttons
/dev/input/event4: ELAN900C:00 04F3:2E5D
/dev/input/event5: ELAN900C:00 04F3:2E5D UNKNOWN
/dev/input/event6: ELAN900C:00 04F3:2E5D UNKNOWN
/dev/input/event7: ELAN900C:00 04F3:2E5D Stylus
/dev/input/event8: ELAN900C:00 04F3:2E5D Stylus
/dev/input/event9: GDIX0000:00 27C6:01F5 Mouse
Change-Id: Id2a6223bdbb2f0693149136baa853ca2efb57815
Signed-off-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78503
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <ericllai@google.com>
|
|
When CBFS verification is enabled, add amdfw_a/b.rom at offset 128 bytes
to account for CBFS file header with hash attribute. When CBFS
verification is disabled, add amdfw_a/b.rom at offset 64 bytes to
account for CBFS file header without hash attribute.
BUG=None
TEST=Build Skyrim, Myst BIOS images with and without CBFS verification
enabled.
Change-Id: Ic374ac41df0c8fb8ce59488881ce5846e9058915
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78425
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
|
|
Fix the hash file names to be used to verify signed PSP binaries when
booting with VBOOT FW Slot B.
BUG=None
TEST=Build and boot to OS in Myst with PSP Verstage enabled using both
VBOOT slots A and B.
Change-Id: I89f02922bc901d8ac71d48bf5128fe6ecead43a0
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78236
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
|
|
Enable RO verification by GSC and RO/RW CBFS verification.
BUG=b:277087492
TEST=Build and boot to OS in Myst with CBFS verification enabled using
PSP verstage.
Change-Id: I2dd3ce59f331f89660185309ccf60c53d50e4fad
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78235
Reviewed-by: Tim Van Patten <timvp@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <ericllai@google.com>
|
|
Some stalls are observed while using CCP DMA in PSP verstage -
especially with CBFS verification enabled. Also with RW CBFS
verification enabled, the entire firmware body is not loaded during
verstage for verification. Instead the files are verified as and when
they are loaded from CBFS. Hence the impact to boot time is reduced
since only few files are loaded during PSP verstage. Hence disable CCP
DMA in PSP verstage until the root cause is identified.
BUG=None
TEST=Build and boot to OS in Myst with CBFS verification enabled.
Change-Id: I22ac108b08abcfe432dfd175644393e384888e11
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78234
Reviewed-by: Martin L Roth <gaumless@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add SPI flash RO ranges to be verified by GSC in order to enable CBFS
verification. Also with CBFS verification enabled, CBFS metadata is
more than 64 bytes. So configure the offset of amdfw_a/b to 128 bytes -
next address aligned to 64 bytes.
BUG=b:277087492
TEST=Build and boot to OS in Myst with and without CBFS verification
enabled.
Change-Id: Ibfffd3d6fce8b80ec156a7b13b387e1df8c43347
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78233
Reviewed-by: Tim Van Patten <timvp@google.com>
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Meteor Lake TME bits [42-45] are reserved regardless of if the part
supports TME or not.
On a device with TME fused off, we noticed some reboot hangs which
have been narrowed down to internal IP routing issues when the IA
accesses the Input Output Manager (IOM) which is mapped at
0x3fff0aa0000 (0x3ff upper 32 bits).
It turns out since TME is fused off, coreboot uses the full physical
address size reported by CPUID MAXPHYADDR (46 bits). Therefore, it
allocates thunderbolt memory range on 46 bits (0x3fff upper 32 bits).
Since 4 of these bits are actually reserved, it seems that this
address range is "stripped down" to 42 bits (=> 0x3ff upper 32 bits)
resulting in potential conflict with other devices such as IOM.
BUG=b:288978352
TEST=No reboot issue on rex with TME fused off
Change-Id: I96ba23ab304257003c0413243d3ac8129ce31743
Signed-off-by: Jeremy Compostella <jeremy.compostella@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78452
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
According the Intel Software Developer Manual,
CPUID.80000008H:EAX[15:8] reports the physical-address width supported
by the processor. Unfortunately, it does not necessarily reflect the
physical-address space the system can actulally use as some of those
bits can be reserved for internal hardware use.
It is critical for coreboot to know the actual physical address size.
Overestimating this size can lead to device resource overlaps due to
the hardware ignoring upper reserved bits. On rex for instance, it
creates some reboot hangs due to an overlap between thunderbolt and
Input Output Manager (IOM) address space.
As some SoCs, such as Meteor Lake, have physical address reserved bits
which cannot be probed at runtime, this commit introduces
`CPU_INTEL_COMMON_RESERVED_PHYS_ADDR_BITS' Kconfig to set the number
of physical address reserved bits at compilation time for those SoCs.
A runtime detection by hardware probing will be attempted if the value
is 0 (default).
BUG=b:288978352
Change-Id: I8748fa3e5bdfd339e973d562c5a201d5616f813e
Signed-off-by: Jeremy Compostella <jeremy.compostella@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78451
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
|
|
This reverts commit 55b7dee2784e9fe80870c6c33ba91b98021df8b5.
Reason for revert: accidentally submitted out of order / breaks tree
Change-Id: Ic15d0e3688cd54f7d678998341263e7bd30e75f2
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78525
Tested-by: Martin L Roth <gaumless@gmail.com>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
|
|
This reverts commit bb5fa6419dfd71950e61e75eecd48ef8203bb1b1.
Reason for revert: accidentally committed out of order; reverting to
unbreak tree
Change-Id: I36aa1fd3a0befe49b7e9e34198676f16fb08cf73
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78524
Reviewed-by: Martin L Roth <gaumless@gmail.com>
Tested-by: Martin L Roth <gaumless@gmail.com>
|
|
Change-Id: I52de5ea3d24b400a93adee7a6207a4439eac61db
Signed-off-by: Nicholas Chin <nic.c3.14@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77535
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
|
|
Having a CBFS cache scratchpad offers a generic way to decompress CBFS
files through the cbfs_map() function without having to reserve a
per-file specific memory region.
This commit introduces the x86 `RAMSTAGE_CBFS_CACHE_SIZE' Kconfig to
set a ramstage CBFS cache size. A cache size of zero disables the
CBFS cache feature. The default size is 16 KB which seems a
reasonable minimal value large enough to satisfy basic needs such as
the decompression of a small configuration file. This setting can be
adjusted depending on the platform needs and capabilities.
To support S3 suspend/resume use-case, the CBFS cache memory cannot be
released to the operating system. There are two options to meet this
requirement:
1. Define a static CBFS cache buffer (located in the .bss section)
2. Create a new CBMEM entry
Option #2 seems more powerful but considering that:
1. The CBFS cache is actually not a cache but just a scratch pad
designed to be isolated between stages
2. postcar is a very short stage not really needing CBFS cache
3. The static initialization of the `cbfs_cache' global
variable (cf. src/lib/cbfs.c) offers a simple and robust design
=> It is simpler to use a static buffer and limit the support to
ramstage.
Since some AMD SoCs (cf. `SOC_AMD_COMMON_BLOCK_NONCAR' Kconfig) define
a `_cbfs_cache' region, an extra `POSTRAM_CBFS_CACHE_IN_BSS' Kconfig
must be set to enable the use of a static buffer as the CBFS cache
scratchpad.
TEST=Decompression of vbt.bin in ramstage on rex using cbfs_map()
Change-Id: I7fbb1b51cda9f84842992e365b16c5ced1010b89
Signed-off-by: Jeremy Compostella <jeremy.compostella@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77885
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Having a CBFS cache scratchpad offers a generic way to decompress CBFS
files through the cbfs_map() function without having to reserve a
per-file specific memory region.
This commit introduces the x86 `PRERAM_CBFS_CACHE_SIZE' Kconfig to set
the pre-memory stages CBFS cache size. A cache size of zero disables
the CBFS cache feature. The default value is 16 KB which seems a
reasonable minimal value enough to satisfy basic needs such as the
decompression of a small configuration file. This setting can be
adjusted depending on the platform needs and capabilities.
We have set this size to zero for all the platforms without enough
space in Cache-As-RAM to accommodate the default size.
TEST=Decompression of vbt.bin in romstage on rex using cbfs_map()
Change-Id: Iee493f9947fddcc57576f04c3d6a2d58c7368e09
Signed-off-by: Jeremy Compostella <jeremy.compostella@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77290
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
This fixes assembling with clang which complains about fpu instructions.
TEST: BUILD_TIMELESS=1 remains the same.
Change-Id: I175b8e749fafde5fb7ffb8101fc0dc892d9b4e0d
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74539
Reviewed-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Enable sending EOP from payload
BUG=b:279184514
TEST=Verify sending EOP from depthcharge on google/rex
Signed-off-by: Kapil Porwal <kapilporwal@google.com>
Change-Id: I5eda0a5c6d4c34cfcc2de898adde0b005d6edc1e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74768
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Enable EC keyboard backlight for dochi.
BUG=b:299284564
TEST=FW_NAME=dochi emerge-brya coreboot chromeos-bootimage
Change-Id: I1b640c576fcdd368110b88cba6f969f10dfc15f1
Signed-off-by: Morris Hsu <morris-hsu@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78395
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Bob Moragues <moragues@google.com>
Reviewed-by: David Wu <david_wu@quanta.corp-partner.google.com>
Reviewed-by: Eric Lai <ericllai@google.com>
|
|
Change-Id: I8d64236fc81e848503535db6f52e93328a60404c
Signed-off-by: Varshit Pandya <pandyavarshit@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78391
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
|
|
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Change-Id: I2419feed1a76ec1cb04cb9640689b8758fa1d3f8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76527
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
|
|
Change-Id: Ief56bff2a1b8825d6e65aeb5f7ed9e8f432e465b
Signed-off-by: Varshit Pandya <pandyavarshit@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78390
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-by: Martin Roth <martin.roth@amd.corp-partner.google.com>
|
|
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Change-Id: I068fcbbcb0641cddce8fa85e2a64ab44d91d6bcf
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76526
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-by: Martin Roth <martin.roth@amd.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
As per PPR, Genoa supports up to 96 core, that is 192 threads.
It also supports dual socket.
Change-Id: I817fea7c41477f476794e9e5c16451037d01f912
Signed-off-by: Varshit Pandya <pandyavarshit@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78402
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martin.roth@amd.corp-partner.google.com>
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
|
|
GPP_H04/GPP_H05 doesn't use for I2C usage, remove I2C2 "on" settings.
BUG=b:294155897
TEST=Check ap firmware log, i2c2 is disabled
Change-Id: I0124fd108fbbd87507d252e9caab4dfc16aceddb
Signed-off-by: Tyler Wang <tyler.wang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78339
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Eran Mitrani <mitrani@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Update SaGv gears and frequency values as per recommendation
from power and performance team. This change doesn't cause
negative impact on firmware boot time performance.
BUG=b:274137879
TEST=Verified the settings on google/rex using debug FSP logs.
Signed-off-by: Bora Guvendik <bora.guvendik@intel.com>
Change-Id: Ie8a81c05f25b1cdab1008d09c606d1debea6e6e4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78268
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
Crypto Engine in PSP prefers the buffer from Static RAM (SRAM). Hence if
a buffer comes from within SRAM address range, then it is passed
directly to Crypto Engine. Otherwise a bounce bufer from the stack is
used. But on SoCs like Picasso where PSP Verstage stack is mapped to a
virtual address space this check fails causing a bounce buffer to be
used and hence a stack overflow. Fix this issue by assuming that the
buffer comes from the SRAM always in such SoCs and pass the buffer
directly to crypto engine.
BUG=b:259649666
TEST=Build and boot to OS in Dalboz with unsigned PSP verstage.
Change-Id: I2161c8f0720c770efa5c05aece9584c3cbe7712a
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78426
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
|
|
The Bayhub BH720 eMMC bridge is a fixed internal device, and needs to
me marked as non-removable in order for Windows to properly recognize/
utilize the device. Add the necessary ACPI to be generated at runtime.
TEST=build/boot/install Win11 on google/kahlee (liara)
Change-Id: I0815abf1d2dc5cfe785dc04670ab91f2a6a1af23
Signed-off-by: CoolStar <coolstarorganization@gmail.com>
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78403
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <ericllai@google.com>
|
|
Windows does not use these devices for audio. Hide these so they don't
clutter device manager.
Change-Id: Ic85eff7f7ff68e25cc005bbb822bf99374c96532
Signed-off-by: CoolStar <coolstarorganization@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78418
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
On all targets the domain works as a host bridge. Xeon-sp code intends
to feature multiple host bridges below a domain, hence rename the
function to pci_host_bridge_scan_bus.
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Change-Id: I4e65fdbaf0b42c5f4f62297a60d818d299d76f73
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78326
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-by: Yidi Lin <yidilin@google.com>
|
|
AMD Audio CoProcessor handles I2S audio on AMD SoC's. Prior to AMD
Ryzen platforms (e.g. STONEY) it is located on the Integrated GFX
device. As the proprietary AMD driver does not support accessing this
easily, reserve a custom ACPI ID from the coreboot namespace so that
another driver can be attached in Windows device manager.
Change-Id: I855b81908ed9ad0587b6367b052c726c36350208
Signed-off-by: CoolStar <coolstarorganization@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78405
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
|
|
Use 2 gpio for stylus detect and wake function.
GPP_E04 is the IRQ source, and GPP_E09 is the wake source.
BUG=b:304680060
TEST=Build and test on karis, stylus detect function works
Change-Id: I7a83326f76932c8e501e6369bb845fc7236291b4
Signed-off-by: Tyler Wang <tyler.wang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78336
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: David Wu <david_wu@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Use runtime detection for touchscreens.
BUG=b:289962599
BRANCH=firmware-nissa-15217.B
TEST=emerge-nissa coreboot
Change-Id: Ia43ada8b3b6dbee95dbadacc353106e0f8f37549
Signed-off-by: Rex Chou <rex_chou@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78338
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Reviewed-by: Eric Lai <ericllai@google.com>
|
|
This Kconfig option is used as a failback when `get_uint_option`
fails. It will fail after coreboot is flashed, as the cfr code has
not yet setup the options.
Change the default to OFF, so when it does fallback, it's the correct
behaviour.
Change-Id: I5d06047fe23322520e9c84ded8f1941f6d716a51
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78223
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
|
|
Change-Id: Id42d07aabfd08c6c7a38515f9cf4b749750deecd
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78202
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This is required for the HDA device to work.
Change-Id: I5fd3617c4cb1e69b7e0ecf6cddf4c143da99b927
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78201
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This adds support for the Librem 11 tablet, using the ME 13.50.15.1436
binary from the original BIOS (version 28.D8.E1.021) and FSP binaries
from a Jasper Lake Chromebook.
The following features were tested with PureOS:
* Audio (speakers, microphone, headset jack)
* Cameras
* Display
* Touchscreen and pen
* Keyboard cover, with tablet/laptop mode switch indicated via ACPI
* Power and volume buttons
* USB-C ports (USB 2/3, DP alt mode, PD charging)
* SD card reader
* WLAN
* Bluetooth
* NVMe SSD (socketed)
* Battery state information from EC
* Accelerometer
A UART is accessible with soldering via test points on the mainboard,
documented in the mainboard Kconfig with a toggle to enable it for
coreboot logging.
Change-Id: I545994889ddfb41f56de09b3a42840bccbd7c4aa
Signed-off-by: Jonathon Hall <jonathon.hall@puri.sm>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78343
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
|
|
Based on schematics and confirm with EE to remove TOF function.
BUG=b:290891557
BRANCH=firmware-nissa-15217.B
TEST=emerge-nissa coreboot
Change-Id: I1ae6a6562d87f8da5f41691a7606a1aa10989443
Signed-off-by: Rex Chou <rex_chou@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78147
Reviewed-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The next board revision of Librem 14 (v1-02) has replaced the ALC256
codec with ALC269. Add verbs for it.
Two GPIOs were changed from SMBus native functions to NC for this
revision. They are not used on either revision, change to NC.
Change-Id: I43b6265d2f502c05d5539ff3abf53ade0da6d706
Signed-off-by: Jonathon Hall <jonathon.hall@puri.sm>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78347
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
New Librem 14s have a newer CPU stepping, which changes them from CML
v1 to v2. The product is not significantly different and remains v1,
specifically "v1-02".
Select SOC_INTEL_COMETLAKE_1_2 to support all CPU steppings.
Change-Id: Iab37208b81e973714a2c088d2346eda518bf1214
Signed-off-by: Jonathon Hall <jonathon.hall@puri.sm>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78346
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
|
|
Define SOC_INTEL_COMETLAKE_1_2, which creates a build supporting both
Comet Lake v1 and v2 by including both sets of FSP binaries and
selecting one based on the CPUID.
A mainboard can select this instead of SOC_INTEL_COMETLAKE_1 or ..._2
to support all CML-U steppings in one build.
Change-Id: Ic8bf444560fd6b57064c47faf038643fabde010e
Signed-off-by: Jonathon Hall <jonathon.hall@puri.sm>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78345
Reviewed-by: Eric Lai <ericllai@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Michał Kopeć <michal.kopec@3mdeb.com>
|
|
Support embedding a second FSP-M/FSP-S binary for an SoC that can
select one at runtime.
Comet Lake v1 and v2 are different steppings of the same SKUs, but they
require different FSP binaries. Supporting both in a single build
requires embedding both FSPs and selecting one at runtime based on the
CPUID. This is desirable for a product that may have different CPU
steppings but is not otherwise differentiated enough for a separate
firmware build.
An SoC can select PLATFORM_USES_SECOND_FSP to indicate that two FSP-M/
FSP-S binaries are required. Implement soc_select_fsp_m_cbfs() and
soc_select_fsp_s_cbfs() to choose one based on platform-specific
criteria. For Comet Lake, the first FSP is CML v1 and the second is
CML v2, but in principle a platform could define any meaning for the
first and second FSP.
FSP-T is not affected, only one FSP-T can be embedded if FSP_CAR is
used.
Only one set of FSP headers is used, which is sufficient for Comet Lake
v1/v2; their headers are equivalent.
ADD_FSP_BINARIES, FSP_USE_REPO, and FSP_FULL_FD are supported for both
sets of FSP-S/FSP-M but cannot be configured separately, both use the
same configuration.
Change-Id: Ied4c6c49a6bdf278238272edd47a2006258be8e5
Signed-off-by: Jonathon Hall <jonathon.hall@puri.sm>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78344
Reviewed-by: Michał Kopeć <michal.kopec@3mdeb.com>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
|
|
Within TBT PCIe, following register offsets have been updated for
production silicon. Update ASL with new offsets.
1. MPC - Miscellaneous Port Configuration Register
2. RPPGEN - Root Port Power Gating Enable
3. SMSCS - SMI/SCI Status Register
BUG=306026121
TEST= Check TBT PCIe Tunnel creation and device enumration.
Change-Id: I0497f7108ef5046c2694aece232263582514a0c5
Signed-off-by: Ravi Sarawadi <ravishankar.sarawadi@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78163
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Jamie Ryu <jamie.m.ryu@intel.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
Commit bd9c562a9e0c6af65f5e798a17ba9a55892ef082 ("acpi: Configure
slp-s0 residency counter frequency in LPIT table") led to jenkins
reporting the following error:
!!!!! Error: defined(CONFIG_ACPI_SOC_INTEL_SLP_S0_FREQ_HZ)
used at src/include/acpi/acpi.h:457. Symbols of type 'hex'
are always defined.
Since hex Kconfig are always defined there is no need to test it being
defined but also no need to handle zero or non-zero values.
In addition:
1. This config was defined in Meteor Lake specific Kconfig file while
it should actually be define closer to where it is being used (here
soc/intel/common/block/acpi/Kconfig) and only set by the SoC Kconfig.
2. Once moved and under control of `SOC_INTEL_COMMON_BLOCK_ACPI_LPIT'
gating (lpit.c), the Kconfig name needed to be adjusted to better fit
its use.
3. Make Meteor Lake Kconfig sets the config but does not define it
anymore.
TEST=LPIT ACPI table Counter Frequency field is set to 0x2005 on rex
Change-Id: I2083c9209e61be6180cca2c9f74097e2f4b4ce9a
Signed-off-by: Jeremy Compostella <jeremy.compostella@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78458
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Bora Guvendik <bora.guvendik@intel.com>
Reviewed-by: Sukumar Ghorai <sukumar.ghorai@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
|
|
The microcode for RPL-S C0 and H0 is actually available, however, the
name of the file contained a typo: 06-b7-05 vs 06-bf-05. Fix the typos
in the comments.
Moreover, the ADL-S C0/H0 microcode file 06-97-05 has the same sha256
sum as the equivalent RPL-S C0/H0 microcode file 06-bf-05. The sha256
sum of ADL-S/RPL-S C0/H0 microcode on intel-microcode tag
microcode-20230808:
5d8d4a4d5456c43b7cc04937c80aec094ccbf3bd89f34ffa5182913ef944a9f9
Update the comments to correctly indicate supported CPU steppings.
Change-Id: I4c848e0dfc40f6c8e26a9b31e7c4cf4c5a09128f
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78413
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The SCI handler for the GPE associated with the Super I/O did not clear
the respective PME status bits resulting in the SCI reoccurring
endlessly. The /proc/interrupts reported millions of ACPI interrupts
generated in just a few minutes of uptime. The flood of interrupts
caused some units to be unusable in extreme cases once attempted to
boot Qubes OS for example. On systems like Qubes OS it had a huge
impact on performance due to many IPCs the SCIs caused under Xen.
Clear the PME bits of devices that report a PME event. Then clear
the global PME status bit at the end of SCI handler to prevent the SCI
from asserting again until a new event occurrs. With this change
the number of ACPI interrupts generated in the first minutes of uptime
settles at a few thousands.
TEST=Boot Qubes OS R4.1.2 on Dell OptiPlex 9010 SFF and check
/proc/interrupts in dom0 if the number of ACPI interrupts is only
a few thousands.
Change-Id: I64e03d268138a62b46084be41343ef7fb089dfc3
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78351
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Krystian Hebel <krystian.hebel@3mdeb.com>
|
