| Age | Commit message (Collapse) | Author |
|---|
|
Add more registers and make them optional, so they keep untouched/
their default if omitted.
Change-Id: I5d8008176d2972976b387c558658b8e70b50af8e
Signed-off-by: Max Blau <tripleshiftone@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32376
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Increase ramstage to 2M, required to actually embed the 7.2mb uImage
into the coreboot.rom, increase the postram cbfs cache in order for the
fit image to be loadable (without this increase the fit payload is found
but not loaded)
Change-Id: Iee0ed9f7958588ceda54bb32253c84cac68abea2
Signed-off-by: Marty E. Plummer <hanetzer@startmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32373
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
The name OPROM is somewhat inaccurate, since other steps to bring
up display and graphics are needed depending on mainboard/SoC.
This patch cleans up OPROM code nomenclature, and works towards
the goal of deprecating vboot1:
* Rename CONFIG_VBOOT_OPROM_MATTERS to
CONFIG_VBOOT_MUST_REQUEST_DISPLAY and clarify Kconfig
description
* Remove function vboot_handoff_skip_display_init
* Remove use of the VbInit oflag VB_INIT_OUT_ENABLE_DISPLAY
* Add |flags| field to vboot_working_data struct
* Create VBOOT_FLAG_DISPLAY_REQUESTED and set in vboot_handoff
BUG=b:124141368, b:124192753, chromium:948529
TEST=make clean && make test-abuild
TEST=build and flash eve device; attempt loading dev/rec modes
BRANCH=none
Change-Id: Idf111a533c3953448b4b9084885a9a65a2432a8b
Signed-off-by: Joel Kitching <kitching@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32262
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
Patch corrects IRQ and GPIO configuration for RT5682 codec's Jack INT.
Switching IOAPIC to GpioInt because ACPI Interrupt() doesn't support
jack triggering on both edges.
BUG=b:130180492
TEST=build and boot on a CML EVT board.
Use evtest & verify headset jack detection functions as expected.
Change-Id: Ia9bf8d554b54554f9ac1e78fd44a508964c8a14d
Signed-off-by: Naveen Manohar <naveen.m@intel.com>
Suggested-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32474
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Shelley Chen <shchen@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Use already defined system_reset() function.
Change-Id: I6e5aff96e06830931acf700593d3e1689857efdc
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32497
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Use already defined system_reset() function.
Change-Id: Ieff4271c4a09d564d5f3415d8bc2c3843c8460f2
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32378
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Use already defined system_reset() function.
Change-Id: I68ff4cffa2bfab6a15299795c3e1837fc9b85806
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32379
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Use already defined system_reset() function.
Change-Id: I32c731de0c30940d15fd01fec6f10b3b33c04370
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32496
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Use already defined system_reset() and full_reset() functions.
Change-Id: Ib7e399b5186aa704d0388c4a4b18480f2e3799f3
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32495
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Use already defined system_reset() function.
Change-Id: I436f62c4402736fb74c59d8b359d0b3963f0e659
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32494
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Use already defined system_reset() and full_reset() functions.
Change-Id: I0a05f3ac5c5340a509024de2b444960f498c3e99
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32492
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Trusted Firmware places some components in SRAM on RK3399 and therefore
restricts accesses to SRAM to the secure world. This makes the vboot
working data inaccessible to normal world payloads, so we need to
migrate it into CBMEM.
Change-Id: Ic7c95790f2f118ccbdd897550f13b5f987bdd831
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32490
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Joel Kitching <kitching@google.com>
|
|
Implement mt_pll_raise_ca53_freq() in MT8183 to raise the CPU frequency.
Move the function declaration to common header.
BUG=b:80501386
BRANCH=none
Test=Boots correctly on Kukui
Change-Id: Ide8d767486d68177fa2bfbcc5b559879eca1bcda
Signed-off-by: Tristan Shieh <tristan.shieh@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32465
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
With the default CPU voltage (0.8v), CPU frequency should be 1417Mhz at
most. We have to raise CPU frequency to 1989MHz after increasing CPU
voltage to 1.05v in romstage.
BUG=b:80501386
BRANCH=none
Test=Boots correctly on Kukui
Change-Id: I4c3e0fa27ccda8e0efe422b6ab503a1efb1697e9
Signed-off-by: Tristan Shieh <tristan.shieh@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32464
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
NEED_VB20_INTERNALS should always be specified when peeking
into vboot internal data structures.
BUG=b:124141368, chromium:956474
TEST=make clean && make test-abuild
BRANCH=none
Change-Id: I5a47a28350fd5a68efeff0d06ca150c1ae145412
Signed-off-by: Joel Kitching <kitching@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32452
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
Disable the GBB flag forcing manual recovery now that we can read
the manual recovery from H1.
Enable the GBB flag to skip EC software sync, since images built
from coreboot.org do not include the EC binaries by default.
Change-Id: I0e1d6304e3e29eda68c7b807cf0774275c37d710
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32476
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This reverts commit 9aae51ad1141a47d5c2f7133b02f5f0ab6168860.
Proper code in cpu/intel/common/ shall be used instead.
Change-Id: I4a5d558b03497d106083eece10c5b34e0e7cbb2d
Signed-off-by: Nico Huber <nico.h@gmx.de>
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/29683
Reviewed-by: Ronak Kanabar <ronak.kanabar@intel.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
We do not want the RX signal to be floating on the board as that could
cause the ISH to remain in a higher power state (because there is logic
to keep the ISH in an higher power state when there is an active UART).
Add an internal 20K pull up on the RX line. In normal configuration this
will burn an additional 544uW.
BRANCH=R75
BUG=b:131241969
TEST=verify that ISH console still works with rework
Change-Id: Ifc9621bcafe4c86edfa9cd6d58b307254d3a81ca
Signed-off-by: Jett Rink <jettrink@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32471
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
If the Intel IGD device pci 02.0 is disabled or undefined in
the device tree, then internal graphics pre-allocated memory
and GFX-VT MMIO memory for virtualization won`t be allocated
in the SoC address space.
Thus, patch resolves the FSP-S hang problem on Skylake/ Kaby
Lake processors when the IGD device is disabled. This should
provide to run FSP 2.0-based coreboot on these CPUs families
without integrated graphics card.
The following boards were used for testing:
- Asrock H110M-DVS board (desktop i5-6600) & NVIDIA GTX 1060
as external GPU.
Virtualization and GFX 3D acceleration with nouveau driver
still works well (tested on VirtualBox 5.1.38 with Ubuntu
18.04.1 as guest and host OS)
- Intel KBL-R U RVP board (mobile i5-8350u) without GFX.
Payload: tianocore edk2-stable201811-216-g51be9d0.
Change-Id: Id7a0cba582d83e3fe7e8d20342ee219cdd369a53
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32467
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Enable audio clock, intbus clock, infra clock and mtkaif
26m clock.Needed by audio playback in firmware.
BUG=b:117254418
BRANCH=none
TEST=Build pass and verified on kukui p1 board
Change-Id: I88060d9796cc23ad7f524943f36869e1ec85073d
Signed-off-by: Jiaxin Yu <jiaxin.yu@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32458
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
|
|
This patch adds the setting of psys_pmax to 136W. According to the
design, Rpsys is 11.8Kohm. Here is the equation to come out the
Psys_pmax value: Psys_pmax * 1.493uA/W * 11.8Kohm / 2 = 1.2V
Hence, Psys_pmax is 136W.
BUG=b:124792558
BRANCH=None
TEST=emerge-sarien coreboot chromeos-bootimage & Ensure the value is
passed to FSP by enabling FSP log & Boot into the OS
Change-Id: Id3f6be5f0c2346a7763195a992c0ae45faede056
Signed-off-by: Gaggery Tsai <gaggery.tsai@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32457
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
|
|
Clear the GPI Interrupt Status & Enable registers to prevent any
interrupt storms due to GPI.
BUG=b:130593883
BRANCH=octopus
TEST=Ensure that the Interrupt status & enable registers are reset
during the boot up when the system is brought out of G3, S5 & S3. Ensure
that the system boots fine to ChromeOS.
Change-Id: Ia3b9d3bf08472219348e20b53bae470c589039fb
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32448
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Add support to reset the GPI Interrupt Status & Enable registers so that
the system does not experience any interrupt storm from a GPI when it
comes out of one of the sleep states.
BUG=b:130593883
BRANCH=None
TEST=Ensure that the Interrupt status & enable registers are reset
during the boot up. Ensure that the system boots fine to ChromeOS.
Change-Id: I99f36d88cbab8bb75f12ab1a4d06437f837841cb
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32447
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Add the offset information for GPI interrupt status and enable register
in the pad_community structure. Populate the concerned information for
individual SoCs. This offset information is required to clear the
interrupt configuration during the bootup.
BUG=b:130593883
BRANCH=None
TEST=Ensure that the interrupt configuration are cleared during bootup.
Ensured that the system boots to ChromeOS.
Change-Id: I8af877a734e8d49b700d720b736da8764985a8f8
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32446
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Use already defined system_reset() function.
Change-Id: Ic4716a3bb1dc6c6b29a028fc0ab28f9195f08416
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32493
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
The ACPI code of LPE device is included regardless of the
availability of the LPE controller.
Linux remains requesting the status of device LPEA even if
this device is disabled.
Include ACPI LPE controller code at Braswell mainboards with
LPE enabled.
BUG=N/A
TEST=Linux 4.17+ on Portwell PQ7-M107
Change-Id: Ic8acf9ea9e9b0ba9b272e20beb2023b7a4716a73
Signed-off-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/29414
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Michał Żygowski <michal.zygowski@3mdeb.com>
|
|
The dqs_map array is used only for LPDDR3 and LPDDR4. It is not used for
DDR4, and so it can be removed from the baseboard memory initialization
code.
BRANCH=none
BUG=b:129706819
TEST=ensure the firmware builds without error; I don't have hardware
available to test this just yet.
Change-Id: I07fac3097d68f37b4630d3f0010f987da2f03bd7
Signed-off-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32484
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
First configuration supported is 8 GB system memory:
4 x 2 GB (K4E6E304ED-EGCG).
BRANCH=none
BUG=b:129706819
TEST=ensure the firmware builds without error; I don't have hardware
available to test this just yet.
Signed-off-by: Paul Fagerburg <pfagerburg@chromium.org>
Change-Id: Ibd92d585118ff75492e8a7188dcdb2a286836d56
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32364
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Intel's DQ_DQS_RComp_Info_Utility generates data for 6 entries. MRC will
return errors if we don't have all 6 entries in the map.
BRANCH=none
BUG=b:131103736
TEST=ensure the firmware builds without error; I don't have hardware
available to test this just yet.
Change-Id: I20a768de0e4440d7dde7b717794c4e2d0c62819c
Signed-off-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32475
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Changes includes:
- enable TPM1 + add entry in devicetree
- configure LPC IO to make IPMI work + add entry in devicetree
- introduce DSDT and SMBIOS entries for IPMI to make it detectable
by ipmi_si driver
Signed-off-by: Lukasz Siudut <lsiudut@fb.com>
Change-Id: Ia975643064075f1f861f4ead6f24ed71f345ea04
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32443
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
|
|
Enable LTR for NVMe so it can use ASPM L1.2.
BUG=b:127593309
TEST=build and boot on sarien and check L1 substate with lspci
before: L1SubCtl1: PCI-PM_L1.2+ PCI-PM_L1.1+ ASPM_L1.2- ASPM_L1.1+
after: L1SubCtl1: PCI-PM_L1.2+ PCI-PM_L1.1+ ASPM_L1.2+ ASPM_L1.1+
Change-Id: I9842beda6767f758556747f83cfcedbd00612698
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32456
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-by: Roy Mingi Park <roy.mingi.park@intel.com>
|
|
Remapping Hardware Status Affinity (RHSA) structure is applicable for
platforms supporting non-uniform memory. An ACPI Name-space Device
Declaration (ANDD) structure uniquely represents an ACPI name-space
enumerated device capable of issuing DMA requests in the platform.
Add RHSA and ANDD structures support for DMAR table generation.
BUG=b:130351429
TEST=Image built and booted to kernel
Change-Id: I042925a7c03831061870d9bca03f11bf25aeb3e7
Signed-off-by: John Zhao <john.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32189
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
The IRQ tables don't support this path, so we shouldn't report presence
of the legacy PICs. As the _PIC method is optional and we ignore the
passed parameter anyway, drop it.
Change-Id: I51301a600e16f74fde00fdcb4595e1f47a52e207
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/29833
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Lance Zhao <lance.zhao@gmail.com>
|
|
Change-Id: Ic1fcbf4b54b7d0b5cda04ca9f7fc145050c867b8
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32014
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Change-Id: If3c9783ebc41c103c915788139d91644b805f397
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/29832
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
|
|
This reverts commit 77fb3632a4a3d3004b3aa4950967be9164d9711d.
Reason for revert: This change inadvertently added a submodule.
Change-Id: I6cc2a3cd9d88986a2599a5ff2e5a066b1396a8c0
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32472
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch revises the AC/DC loadline settings because some major
layout changes between proto and evt boards.
BUG=b:130740639
BRANCH=None
TEST=emerge-atlas coreboot chromeos-bootimage and boot to the OS.
Change-Id: Iea12c621e7fab427a0de8f43f0290bf01d0c5a09
Signed-off-by: Gaggery Tsai <gaggery.tsai@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32359
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: caveh jalali <caveh@chromium.org>
Reviewed-by: Caveh Jalali <caveh@google.com>
|
|
BUG=crbug:948241
TEST=Booted and decompiled the table
[000h 0000 4] Signature : "MCFG"
[004h 0004 4] Table Length : 0000003C
[008h 0008 1] Revision : 01
[009h 0009 1] Checksum : 15
[00Ah 0010 6] Oem ID : "COREv4"
[010h 0016 8] Oem Table ID : "COREBOOT"
[018h 0024 4] Oem Revision : 00000000
[01Ch 0028 4] Asl Compiler ID : "CORE"
[020h 0032 4] Asl Compiler Revision : 00000000
[024h 0036 8] Reserved : 0000000000000000
[02Ch 0044 8] Base Address : 00000000F8000000
[034h 0052 2] Segment Group Number : 0000
[036h 0054 1] Start Bus Number : 00
[037h 0055 1] End Bus Number : 40
[038h 0056 4] Reserved : 00000000
Change-Id: I46dc1959971af4685a7ffd285429175d6882ae86
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32445
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
CPU's featuring a non eviction mode cache the whole ROM.
Therefore XIP stages don't need to follow some alignment constraints.
Change-Id: I4a30f31baa0f90279c0690ceb6aefea6de461bd9
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32442
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Change-Id: I4835ca3e20f2e53598bfc77b633aca946d3fde9c
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32431
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Change-Id: I8d80084095912c30bfd8fc100bf27b522485a08a
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32430
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Change-Id: Ic6eb9c7dbfc5fde97f0f45f09431c617cb850c38
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32429
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
'param' variable is unused because 'printram' function only expands to
something in debug builds (not default ones).
Change-Id: I0cdf34cbb9aaed5045db5294eeefeaac642aeb1a
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32428
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Jacob Garber <jgarber1@ualberta.ca>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I3b5092aa076b9693f78c86ffb9b99805696bb0bb
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32427
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Change-Id: I143f3395a385e170cce0979707d6a7f61107f40b
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32426
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Change-Id: Ie81377a31e6527c5fd5aaea99f08527912e870a0
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32425
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
The `printram` function only expands to a value only in debug builds.
This isn't done in default builds.
Change-Id: Ic88c4cc730ae2d0d0718c7f71260cd2b45a3ddcd
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32424
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Change-Id: Idd339e324b833d2d024edb45e33c3d74af4473e8
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32423
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Change-Id: Ibdfbf1031130ff861c4313d1271d6ccb68bf8837
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/29917
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Update submodule pointer to pull in newly-updated Braswell FSP.
Adjust FSP_FD_PATH for soc/cannonlake due to filename case change.
Change-Id: I02ee0d32fd4c04cd4971eff20fc5a7de3f9b07ec
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32420
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
|
|
Add FP_RST_ODL to early GPIO table, configured as low, so that the FPMCU
will get reset when coreboot enters bootblock.
BUG=b:130229952
BRANCH=none
TEST=Compiles (no Hatch device w/FP to test)
Change-Id: I8a8d8cc2c560f6518337f7500575fdc2265b6347
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32419
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
|
|
Lynx Point switched to doing mainboard-specific super I/O setup in the
bootblock with commit d893a2635fdd ("sb/intel/lynxpoint: Enable LPC/SIO
setup in bootblock"). The X10SLM+-F was added while that commit was in
review, and hence did not receive the necessary changes to SIO setup.
This patch has not been tested on hardware.
Change-Id: I7a648ec967dea2113cbbde1a93c1963ca6dd3c88
Signed-off-by: Tristan Corrick <tristan@corrick.kiwi>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32406
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
On EC end, we want to change this pin from push-pull to open-drain.
And since there is no external pull-up resistor on the board, we'll
have to configure this pin as internal-pull-up on AP end.
BUG=b:129306003
TEST=None
Change-Id: Ibc1f89fc25773220db009c6571400b01390dd756
Signed-off-by: Philip Chen <philipchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32292
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
FIT support takes more heap memory than most coreboot payloads.
Change-Id: Id17f25e94d97e937b0e9a9cee3dd1a8aef1d525d
Signed-off-by: Marty E. Plummer <hanetzer@startmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32392
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
Add common SoC config.
Disable PCIe WiFi.
Add digitizer.
Turn off native SD card interface.
No WWAN.
Add DA7219 driver to Kconfig.
BUG=b:130310626
BRANCH=none
TEST=compiles (no Hatch ref or Kohaku device to test)
Change-Id: I17d5ba6ce4ec412384e4a1678474b8d26499ba40
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32405
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Not all Hatch variants utilize the SoC's native SD card support. Move
the support to board-specific variants instead of the base device tree.
BUG=none
BRANCH=none
TEST=compiles (no Hatch device to test with)
Change-Id: Iae24114aad2c4d042c25da6f8cb740ccc8960082
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32417
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Similar to hatch(CB:32278), this change sets SerialIo
config for UART0 to PchSerialIoSkipInit to skip initialization in
FSP.
This change also adds a device to kohaku override tree to ensure that
the settings in it take effect.
BUG=b:130310626
Change-Id: Ia25b45811be26d55fc0019e4cd22eb7310b5a4c4
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32398
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
Enable acoustic noise mitgation for arcada platform,
the slow slew rates for Ia and Gt are fast time dived by 8.
BUG=b:131144464
TEST=waveform test and hardware validation result pass.
Signed-off-by: nathan chen <nathan_chen@wistron.corp-partner.google.com>
Change-Id: I37315ecfa245fce3085e62d1566ff037d8aa8ab4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32403
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Disable the POWER_OFF_ON_CR50_UPDATE option on sarien/arcada. This is
needed so that platform properly boots after doing a Cr50 firmware
update when running on battery.
BUG=b:126632503
BRANCH=none
TEST=Build coreboot on sarien/arcada.
TEST=Perform Cr50 firmware update on Sarien, confirm the platform boots
normally after sending TURN_UPDATE_ON to the Cr50.
Change-Id: I0b687285eb95070eaffb68611a7d98eb8434ce2c
Signed-off-by: Keith Short <keithshort@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32436
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Modify the POWER_OFF_ON_CR50_UPDATE Kconfig option so that specific
mainboard implementations can disable the option.
BUG=b:126632503
BRANCH=none
TEST=Build coreboot on sarien/arcada.
TEST=Perform Cr50 firmware update on Sarien, confirm the platform boots
normally after sending TURN_UPDATE_ON to the Cr50.
Change-Id: I3beefaae21de61e53ae232dbdc8ea9dbb2c78cd5
Signed-off-by: Keith Short <keithshort@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32435
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This change will save touchscreen power leakage 2-3mW in S0iX and
increase T2 display time delay to meet display panel requirement.
BUG=b:129899315
TEST= Measure touchscreen power from Sarien during S0iX
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I48419132ba734f20ad5cf484c2dda609570a6dd0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32330
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Sarien will change Melfas from HID to I2C and change address from
0x10 to 0x34. So we don't need VPD to separate Elan and Melfas
anymore.
BUG=b:131194574
TEST=boot up and check no Melfas HID device exist
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: Ic002f61b226743e1c18dbdbc51ce8b733916d8a0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32437
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
We want to disable touch for non-touch sku. We can use
strap pin GPP_B4 to identify it is connected with touch
or not.
touch sku: GPP_B4 is low
non-touch sku: GPP_B4 is high
BUG=b:131132419
TEST=boot up and check no touch device exist
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: If6681262c25e4b01e061a8520e38905d40345509
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32438
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Set CPU frequency from 1100MHz to 1989MHz to improve booting time.
BUG=b:80501386
BRANCH=none
Test=Boots correctly on Kukui
Change-Id: Id41c7ea8905c4db2537a5c32f96eb7c6b2c008ea
Signed-off-by: Tristan Shieh <tristan.shieh@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32397
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-by: You-Cheng Syu <youcheng@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The maximum CPU frequency is 1417MHz with current processor voltage
(0.8v). Set processor voltage to 1.05v for higher CPU frequency.
BUG=b:80501386
BRANCH=none
Test=Boots correctly on Kukui
Change-Id: I24ecdac2c85d3f012d9235449c0d727d727dc185
Signed-off-by: Tristan Shieh <tristan.shieh@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32396
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: You-Cheng Syu <youcheng@google.com>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
|
|
SSD reset pin had been added on DVT2, the power sequnence requires
toggle in boot stage.
BUG=b:130741066
TEST=Boot up with simulated DVT2 platform and confirm SSD can be
detected during warm reboot.
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Change-Id: Ie734875a49b8b61f8b813c473d30cbcaf4dd13d1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32434
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Tune I2C params for I2C buses 5, 6, and 7 to ensure that the
frequency does not exceed 400KHz.
BUG=b:131132499, b:128998988
BRANCH=octopus
TEST=emerge-octopus coreboot chromeos-bootimage and measured frequency
under 400 KHz
Change-Id: Ie8cfba72a0654402ccb0274c00b44fbfa2deea21
Signed-off-by: Tony Huang <tony-huang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32404
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Add goodix touchscreen support
BUG=b:131082228
BRANCH=octopus
TEST=emerge-octopus coreboot and verify that touchscreen works on
bloog.
Change-Id: I0b3b481ca806b6452d67ace5dfe53f12a14ac3be
Signed-off-by: Tony Huang <tony-huang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32387
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Change-Id: I556d00e8b06f631a5ca51ae2b5ba646e5f536480
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32422
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add support of GPIO IRQ APIs.
Change-Id: I11715a93999012622a5e28455731cbe249ba8f2c
Signed-off-by: Shefali Jain <shefjain@codeaurora.org>
Signed-off-by: Taniya Das <tdas@codeaurora.org>
Signed-off-by: Nitheesh Sekar <nsekar@codeaurora.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32241
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Update SPI enable/disable and configure clock
API for supporting all the blsp and qup for qcs405.
Change-Id: I39622571cb671f62312283a010129ceecb654f61
Signed-off-by: Shefali Jain <shefjain@codeaurora.org>
Signed-off-by: Taniya Das <tdas@codeaurora.org>
Signed-off-by: Nitheesh Sekar <nsekar@codeaurora.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32240
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Fixes src/northbridge/intel/sandybridge/raminit_mrc.c:286:3: error:
implicit declaration of function 'enable_usb_bar'
Change-Id: I48bf59c56b518477a3fc0d75902fc58df6b7def7
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32400
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: Ic23eb57a4096d4301d7f9478d8e65aaeb233de7b
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32399
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Change-Id: I7669b8dc07b1aa5f00e7d8d0b1305b3de6c5949c
Signed-off-by: T Michael Turney <mturney@codeaurora.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32287
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
When coreboot checks the TPM and key-ladder state it issues a reboot of
the Cr50 with a delay parameter. Older Cr50 code doesn't support the
delay parameter and reboots immediately, which prevented coreboot from
running the mainboard specific code needed for the AP to come back up.
This change calls mainboard_prepare_cr50_reset() prior to sending the
VENDOR_CC_IMMEDIATE_RESET command.
This change also fixes a false error message from the coreboot log that
indicated "Unexpected Cr50 TPM mode 3" when the Cr50 key ladder is
disabled.
BUG=b:130830178
BRANCH=none
TEST=build coreboot on sarien and grunt platforms.
TEST=Load Cr50 v3.15, run 'gsctool -a -m disable; reboot'. Verify
corebot send the
VENDOR_CC_IMMEDIATE_RESET command and that the AP boots normally.
Verify event log shows "cr50 Reset Required"
TEST=Force Cr50 automatic update. Verify event log shows "cr50 Update
Reset".
Change-Id: Ib05c9cfde8e87daffd4233114263de5b30822872
Signed-off-by: Keith Short <keithshort@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32365
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Declare plaform level hook method before and after system sleep for
possible power management related usage.
BUG=N/A
TEST=pass with make what-jenkins-does
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Change-Id: Ie63711748b6dbb99d34910824f2059464543e162
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32366
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: Ie8c5d5f7dd5b43becc144fd5e62d7de2f1ed3b80
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31432
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Without VBOOT_MEASURED_BOOT there is no need for these symbols.
Change-Id: I96391b7817c79f760713c67bc469164b5514879e
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32383
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Tested config:
Interleaved (config; status before, after):
DIMM{0 + 2}: ok, ok
DIMM{0 + 3}: Nok, ok
DIMM{1 + 2}: ok, ok
DIMM{1 + 3}: Nok, ok
DIMM{1 + 2 + 3}: ok, ok
DIMM{0 + 2 + 3}: ok, ok
DIMM{0 + 1 + 2}: ok, ok
DIMM{0 + 1 + 3}: Nok, ok
Not Interleaved:
DIMM{0 + 1 + 3}: Nok, Nok
DIMM{0 + 1 + 2}: ok, ok (with single ranked)
DIMM{0 + 1 + 2}: Nok, Nok (with only dual ranked)
DIMM{0 + 2 + 3}: Nok, ok
DIMM{1 + 2 + 3}: ok, ok
Change-Id: Ibf130a3d4b6f8fa816f7a5f06822a9b8807be3d4
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31007
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Commit 45d4b17 [nb/intel/sandybridge: Move southbridge code to bd82x6x]
moved early_pch_init() to the southbridge, but failed to include
early_pch.c for the non-native raminit case, which now fails to link.
As all boards default to native raminit, this was missed by the autobuilder.
Adjust early_pch.c to be compiled regardles of ram init type used
Test: build/boot google/stout with MRC ram init selected
Change-Id: I50db30fda9a1099fb434c04ea97bcc38f8455233
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32382
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
For full reset, use already defined full_reset() function.
Change-Id: Iec7dcf285f3cb1cdc8f48d348ff8496879625db5
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32377
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
This allows for serial console during the bootblock and enables
console in general for the bootblock.
Change-Id: I5c6e107c267a7acb5bf9cbeb54eb5361af3b6db4
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/30315
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Parameter passing is incorrect here, it should pass
complete StdHeader instead of attempting to fill
in HeapStatus that should be treated as a field private
to AGESA, based on where it is defined in the header
files.
Furthermore the while() loop did not evaluate the
return value. Feature can be brought back at a later
date after someone verifies it actually works correctly
across different stages.
Change-Id: Ib243b275f8700ecaeb330772c795d305c61899c5
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31484
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Each entrypoint to AGESA goes through the same sequence
and have same the function signature.
To avoid introducing bunch of preprocessor magic, rename
all the agesawrapper_amdXXX() functions that are actual
entrypoints to AGESA API, make them static, and provide
a single exposed entry function agesa_execute_state().
Change-Id: I96ae1874132da3843aa42c2f4e8a59ec771d3893
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31483
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This change will save touchscreen power leakage 2-3mW in S0iX and
increase T2 display time delay to meet display panel requirement.
BUG=b:129899315
TEST= Measure touchscreen power from Arcada during S0iX
Change-Id: I4b8f3fdc0d107b080c5febe6fa5d29ea5d1ed0fc
Signed-off-by: Roy Mingi Park <roy.mingi.park@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32311
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
|
|
Add SMBIOS type 9 system slots into coreboot, the definiation is up to
date with SMBIOS spec 3.2
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Change-Id: Ibcfa377c260083203c1daf5562e103001f76b257
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32293
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
|
|
This change is mainly to control PlatformDebugConsent FSP UPD.
PlatformDebugConsent is enabled if SOC_INTEL_CANNONLAKE_DEBUG_CONSENT != 0.
PlatformDebugConsent in FspmUpd.h has the details.
BUG=b:130203864
TEST=boot ok and PlatformDebugConsent can be controlled by Kconfig
Change-Id: Ib845b5e42bc78fb352a0c97c6301f2aeca522f29
Signed-off-by: Kane Chen <kane.chen@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32297
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
SOC_INTEL_DEBUG_CONSENT config is generally to enable default debug
interface of SoC.
Ex: USB DBC, DCI debug interface on cnl, whl, cml.
Change-Id: I313d80d6c63fd37164c63f78e9e69d3cb4a5566b
Signed-off-by: Kane Chen <kane.chen@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32337
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Linux remains using SPI1 and PWM ASL even if these devices are disabled.
SPI1 and PWM are disabled by Intel FSP.
Remove ASL code.
BUG=N/A
TEST=Boot Ubuntu on Intel CherryHill CRB
Change-Id: Iec2ca7520081d00bf7a53d58ee054aa6f23e5606
Signed-off-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/29417
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
|
|
Serial bus revision [Byte 3] and serial bus specific revision [Byte 9]
are not the same.
Change-Id: I366f62e6aa0e9c0dfbc1ec17adeebc42a0e777eb
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32329
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
|
|
Include pch.h in the source files instead in sandybridge.h.
Tested on Lenovo T520 (Intel Sandy Bridge).
Still boots to OS, no errors visible in dmesg.
Change-Id: I9e5b678e979a8d136d8d00b49486d0a882f77d81
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32065
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Change-Id: I2e1011d9ac93ed764b6c2aa425928a972ec2aa43
Signed-off-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32322
Reviewed-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: Ib843eb7144b7dc2932931b9e8f3f1d816bcc1e1a
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/26796
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: David Guckian
|
|
Change-Id: Iddba5b03fc554a6edc4b26458d834e47958a6b08
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32214
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: David Guckian
|
|
Change-Id: Ie21c390ab04adb5b05d5f9760d227d2a175ccb56
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32122
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
Also use macros instead of magic numbers.
Change-Id: I00bd687c487894c72d4e4363774dbcdfaf62dd54
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31310
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
|
|
The pci_or_configx function makes the code shorter and more readable.
Change-Id: Ic1ba250f8ac9fb75cf3252aec18af80842bda7dd
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32310
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Signed-off-by: Thejaswani Putta <thejaswani.putta@intel.com>
Change-Id: I15973ac28e9645826986cf63d2160eedb83024e4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32290
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Droid/Blorb supports keyboard backlight feature, so enable the ASL code.
BUG=b:130330141
BRANCH=octopus
TEST=Build and boot to OS, verify that the string 'KBLT' is in the DSDT.
Change-Id: I74684e3905d34b61fa4b851798dbca018f986e5a
Signed-off-by: Pan Sheng-Liang <sheng-liang.pan@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32298
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marco Chen <marcochen@google.com>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: David Wu <david_wu@quanta.corp-partner.google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This reverts commit 41dad286d846819242a84fc65faed2bbb35845ac. The change will make s0ix fail on Sarien/Arcada Platform.
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Change-Id: I169bc6f41fba82fcf515267e8e1d08aa5ee2dce4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32391
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
