| Age | Commit message (Collapse) | Author |
|---|
|
RaptorLake introduces the support of the Voltage Regulator Fast Vmode
feature. When enabled, it makes the SoC throttle when the current
exceeds the I_TRIP threshold. This threshold should be between
Iccmax.app and Iccmax and take into account the specification of the
Voltage Regulator of the system.
This change provides a mean to:
1. Enable the feature via the `vr_config->enable_fast_vmode'. If no
I_TRIP value is supplied FSPs picks an adapted I_TRIP value for
the current SoC assuming a Voltage Regulator error accuracy of
6.5%.
2. Set the I_TRIP threshold via the `vr_config->fast_vmode_i_trip'
field.
These new fields are considered independent from the other `vr_config'
fields so that the board configuration does not have to unnecessarily
supply other VR settings to enable Fast VMode.
Information about the Fast VMode Feature can be found in the following
Intel documents:
- 627270 ADL and RPL Processor Family Core and Uncore BIOS
Specification
- 724220 RaptorLake Platform Fast V-Mode
- 686872 RaptorLake Lake U P H Platform
BUG=b:243120082
BRANCH=firmware-brya-14505.B
TEST=Read I_TRIP from the Pcode and verify consistency with
a few `enable_fast_vmode' and `fast_vmode_i_trip' settings.
Signed-off-by: Jeremy Compostella <jeremy.compostella@intel.com>
Change-Id: I313acf01c534d0d32620a9dedba7cf3b304ed2ee
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66917
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Bora Guvendik <bora.guvendik@intel.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Add configuration to bump up the SPI flash bus speed from 66 MHz to 100
MHz starting the board version where required schematics update is done.
BUG=b:245949155
TEST=Build and boot to OS in Skyrim with 100 MHz SPI bus speed. Perform
warm and cold reboot cycles for 100 iterations each. Observe that the
boot time improved by ~115 ms compared to 66 MHz SPI flash bus speed.
At 66 MHz:
508:finished loading body 538,319 (83,806)
11:start of bootblock 1,196,809 (624,777)
14:finished loading romstage 1,236,905 (39,163)
970:loading FSP-M 1,237,056 (37)
15:starting LZMA decompress (ignore for x86) 1,237,073 (17)
16:finished LZMA decompress (ignore for x86) 1,358,937 (121,864)
8:starting to load ramstage 2,010,304 (0)
15:starting LZMA decompress (ignore for x86) 2,010,312 (8)
16:finished LZMA decompress (ignore for x86) 2,067,181 (56,869)
971:loading FSP-S 2,078,232 (7,999)
17:starting LZ4 decompress (ignore for x86) 2,078,253 (21)
18:finished LZ4 decompress (ignore for x86) 2,084,297 (6,044)
90:starting to load payload 2,316,933 (5)
15:starting LZMA decompress (ignore for x86) 2,316,947 (14)
16:finished LZMA decompress (ignore for x86) 2,339,819 (22,872)
Total Time: 2,464,338
At 100 MHz:
508:finished loading body 515,118 (59,364)
11:start of bootblock 1,115,043 (566,110)
14:finished loading romstage 1,146,713 (29,697)
970:loading FSP-M 1,146,865 (38)
15:starting LZMA decompress (ignore for x86) 1,146,881 (16)
16:finished LZMA decompress (ignore for x86) 1,249,351 (102,470)
8:starting to load ramstage 1,900,568 (1)
15:starting LZMA decompress (ignore for x86) 1,900,576 (8)
16:finished LZMA decompress (ignore for x86) 1,956,337 (55,761)
971:loading FSP-S 1,967,357 (7,930)
17:starting LZ4 decompress (ignore for x86) 1,967,377 (20)
18:finished LZ4 decompress (ignore for x86) 1,972,925 (5,548)
90:starting to load payload 2,205,300 (6)
15:starting LZMA decompress (ignore for x86) 2,205,313 (13)
16:finished LZMA decompress (ignore for x86) 2,227,087 (21,774)
Total Time: 2,349,804
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Change-Id: I5e8db22151fbc2db1f9e81b3644338348160736d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68116
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jon Murphy <jpmurphy@google.com>
|
|
Based on DMTF SMBIOS Specification 3.5.0
Signed-off-by: Erik van den Bogaert <ebogaert@eltan.com>
Change-Id: I710124ca88dac9edb68aab98cf5950aa16c695d3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67926
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
use function to check if pci device is on a particular bus
number.
TEST: compiled and qemu run successfully
Signed-off-by: Fabio Aiuto <fabioaiuto83@gmail.com>
Change-Id: I4a3e96381c29056de71953ea2c39cd540f3df191
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68103
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
use functions to check for pci devices instead of open-coded
solution.
TEST: compiled and qemu run successfully
Signed-off-by: Fabio Aiuto <fabioaiuto83@gmail.com>
Change-Id: Idb992904112db611119b2d33c8b1dd912b2c8539
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68102
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
add functions to check whether a device is enabled pci
device or a pci device on a specific bus number.
TEST: compile and qemu run successfully
Signed-off-by: Fabio Aiuto <fabioaiuto83@gmail.com>
Change-Id: I3257c8404017372f6cdd9f6cf9453502447343a0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68101
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This change updates scl_lcnt, scl_hcnt, sda_hold value for I2C5 to
follow I2C specification.
I2C_TCHPAD_SCL high period time is from 0.53 us to 0.6952 us.
I2C_TCHPAD_SDA hold time is from 0.13 us to 0.4623 us.
BUG=b:249031186
BRANCH=brya
TEST=EE check OK with test FW and TP function is normal.
Signed-off-by: John Su <john_su@compal.corp-partner.google.com>
Change-Id: I5977f0dbba8924cc8a1c72c36358d6ba6f2de940
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67920
Reviewed-by: Ricky Chang <rickytlchang@google.com>
Reviewed-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Frank Wu <frank_wu@compal.corp-partner.google.com>
|
|
Configure eMMC DLL tuning values for Pujjo board.
BUG=b:241854926
TEST=Use the value to boot on Pujjo successfully.
Signed-off-by: Leo Chou <leo.chou@lcfc.corp-partner.google.com>
Change-Id: Ic36c817fa546741e394668297ca43db3a45ee105
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68095
Reviewed-by: Reka Norman <rekanorman@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
An optional dGPU can be connected to the second PEG bridge:
-[0000:00]-+-00.0 Intel Corporation Xeon E3-1200 v3/4th Gen Core Processor DRAM Controller
+-01.0-[01]--
+-01.1-[02]----00.0 NVIDIA Corporation GK208M [GeForce GT 730M]
It's possible that the 01.0 bridge is never populated, but we have to
leave it on anyway so 01.1 can be enumerated.
Change-Id: Ieab7a7bf3b31b4ee9d9f12b5d827d866c87356e1
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68099
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Given the embedded nature, the Halo SKU, SO-DIMMs and 1 DIMM per
channel, `mobile` seems to come closest.
Change-Id: Ia27f1e4dec0a0d06be3d8c08bfe82becd41a2149
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67399
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
BUG=b:250470706
TEST=Boot to OS on pujjo and check that stylus GPIO are
configured based on fw_config.
Signed-off-by: Leo Chou <leo.chou@lcfc.corp-partner.google.com>
Change-Id: I4218748cb06426a918d89f688599c652062ac78c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68075
Reviewed-by: Reka Norman <rekanorman@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The values in this patch were found in the following datasheets:
* 334819 (APL)
* 336561 (GLK)
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Change-Id: I14c5933b9022703c8951da7c6a26eb703258ec37
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66230
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
SMMSTOREv2 requires 64k min size, 64k alignment.
TEST=build skyrim with SMMSTOREv2 enabled
Change-Id: I3501b6036df9ee1049a92e26a7b72e53b4604f60
Signed-off-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68124
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
SMMSTOREv2 requires 64k min size, 64k alignment.
TEST=build guybrush with SMMSTOREv2 enabled
Change-Id: I78cb873a5634c659067367260cc7063fbd60d77a
Signed-off-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68123
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
The patch uses is_devfn_enabled() function to enable the TBT PCIe ports
through FSP-M and FSP-S UPDs. Also, removes unused tbt_pcie_port_disable
array member from soc_intel_meteorlake_config struct.
TEST=Build coreboot for Google/Rex
Signed-off-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Change-Id: Ie55e196bd8f682864b8f74dbe253f345d7184753
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67831
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
|
|
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Change-Id: I714867d455c4e0d01d6cb1cb9dc64669fb41100c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66319
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
The Lite Mk IV's can enable fast charging, with support up to 100W
via USB-C PD 3.0.
The default for this is disabled, as it can reduce battery life
span. This patch adds the option to enable fast charging, by
writing 0x01 to 0x18 in the EC space.
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Change-Id: Ie01eb59d3f41b242190973fd9c58b1494320c12a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66298
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Add variant specific cmos files, which avoid options like "FastCharge"
existing in platforms that don't support such options.
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Change-Id: I04264cf72d47ef719acfd144d8bf9acb0ceccc11
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66297
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Add variant specific cmos files, which avoid options like "Thunderbolt"
existing in platforms that don't support such options.
This change also removes entries that were never used, including:
* smi_handler
* usb_always_on
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Change-Id: I359e5c5bbf29eb474f2d3bc42a8e80afc0a5d38a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66296
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Change-Id: Iba746431496b30daba098716337b688314eac283
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68081
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
|
|
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Change-Id: I61d4a188dc9526b71277c05dd317255fc9727414
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68080
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
|
|
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Change-Id: I5d9bc4ae942ba171a5d3ef4f77da69398fbac692
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68079
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
|
|
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Change-Id: I00e9636fa49c402f38119ba0bfc85c8c193fec12
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68052
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
|
|
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Change-Id: Ibacf704d362eecea3f7216ffcb02c2ef6f9a6d8f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68051
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
|
|
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Change-Id: Ie5d7d1dd446428d12a2f904545682e8fb9cd82f9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68050
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
|
|
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Change-Id: Ie23472d45c8232f5c907ec1757a648fa1a27d533
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68049
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
|
|
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Change-Id: Ibcd61e44f8e165627851e2c5325985f0765634b6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68048
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
|
|
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Change-Id: Icf459f07948cd29eb251b49fcecefb98c5f5f259
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68047
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martin.roth@amd.corp-partner.google.com>
|
|
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Change-Id: I908445b9f87b3db90527955116db22bbee674e1f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68046
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martin.roth@amd.corp-partner.google.com>
|
|
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Change-Id: I360e4f8ed3b87225a09c7cbb761c570a579771cf
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68045
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
|
|
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Change-Id: I94a81a30950cca6be5ba36a25f8bc6f87c2aad2f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68044
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
|
|
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Change-Id: I7e84760566db5da7ff88dcbe9fb028ebcb390bdc
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68043
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
|
|
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Change-Id: I0ab39ff20b0fb59026063e064e20ce901c2985fe
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68042
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
|
|
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Change-Id: I9b85836ac21da5b885a97f05e3973fb23a052fd5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68041
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
|
|
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Change-Id: I84639389ac1066468b82bb13d684e5423b909fcb
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68040
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
|
|
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Change-Id: I221a2bdb19cc7d17265c69d3fe3e1dfb490e7186
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68039
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
|
|
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Change-Id: I55412395071f0fccb839c40fefda998befaddebb
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68037
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
|
|
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Change-Id: I2ee8ef017d8a3409cbf47f1ed252a512dead224e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68036
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
|
|
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Change-Id: I1d2d85ff8cfca58295117b5cb625cadfc9008311
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68035
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
|
|
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Change-Id: I6870fb9f3d41ef5dc6599e979ce0c890a1e145ab
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68034
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
|
|
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Change-Id: I85e60c189c1ec1da5cf0e5b864447ef6f7b3f548
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68033
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
|
|
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Change-Id: I36c54e62797e67c1732f8deaf8843daf35610e22
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68032
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
|
|
Remove <stdint.h>, <stddef.h> and add <stdbool.h>. All of them are
included through <types.h>.
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Change-Id: If5296988c68302896e3676d7b80d0f133d5d4264
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68031
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
|
|
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Change-Id: I8c61f2a033f9630d3fa3eb5e364e6f38de5c7064
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68038
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
|
|
Currently, after the PCIe link is initialized, we wait 100ms every
time the link is not up anymore. However, this causes significant
delay. Assuming the first check is false, we'd like to increase the
frequency of checks for the link to be up. Changing to check every
10ms instead. This seems to save about 90ms in the device
configuration stage of bootup on herobrine.
BUG=b:218406702
BRANCH=None
TEST=reboot from AP console (on herobrine)
prior to fix (from cbmem dump):
40:device configuration 919,391 (202,861)
after fix (from cbmem dump):
40:device configuration 826,294 (112,729)
Change-Id: Ic67e7207c1e9f589b34705dc24f5d1ea423e2d56
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67884
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <inforichland@gmail.com>
Reviewed-by: mturney mturney <quic_mturney@quicinc.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
|
|
Intel Core i5-10210U can have the following IGD Device IDs
0x9B21/0x9B41/0x9BAC/0x9BCA/0x9BCC according to Intel ARK. Some of
these IDs were not present in coreboot source nor hooked to the
common graphics driver. Add the missing IDs so that the graphics
driver will probe on the mentioned processor and detect the
framebuffer.
TEST=Boot Protectli VP4650 with i5-10210U and see framebuffer is
detected when using FSP GOP and libgfxinit.
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Change-Id: Iee720a272367aead31c8c8fa712bade1b6e53948
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67975
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Commit 37a89d519d4e ("ec/lenovo/h8/acpi: Replace Not() with ASL 2.0
syntax") mixed up boolean and bit-wise operators while replacing Not()
with ASL 2.0 syntax. Thus, fix that.
Built dsdt.aml of lenovo/x230 and differs, but it remains the same when
this commit is applied after commit 37a89d519d4e.
Change-Id: Ifa848aafb5480acaac4fabffcf90a3dbf5248e43
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66380
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
To support an RPL SKU on brya0, brya0 must use the FSP for RPL.
Select SOC_INTEL_RAPTORLAKE for brya0 so that it will use the RPL
FSP headers for brya0.
BUG=b:248126749
BRANCH=firmware-brya-14505.B
TEST=cherry-pick Cq-Depends, then "emerge-brya intel-rplfsp
coreboot-private-files-baseboard-brya coreboot chromeos-bootimage",
flash and boot brya0 to kernel.
Cq-Depend: chromium:3893035, chrome-internal:4983198
Change-Id: I2dd84757532d734ad97b74ba960537d937fb313e
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68094
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: YH Lin <yueherngl@google.com>
Reviewed-by: Bora Guvendik <bora.guvendik@intel.com>
|
|
Add a new THERMAL FW_CONFIG bitfield for describing power consumption
category of SoC.
BUG=b:250089101
TEST="emerge-brya coreboot chromeos-bootimage", flash and boot brya0
and skolas to kernel.
Change-Id: Iba3bd87abd4c112ceff4bbe51a7cf9eae3a694f2
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68025
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: YH Lin <yueherngl@google.com>
Reviewed-by: Tarun Tuli <taruntuli@google.com>
|
|
1) Make the skolas FW_CONFIG field defintions compatible with the
brya0 FW_CONFIG field definitions to support skolas being a SKU of
brya0, and in sync with the config.star definitions for the FW_CONFIG
field for brya0 and skolas.
- brya0 specific changes:
1) remove WFC_MIPI_OVTI5675 definition (was 1)
2) redefine WFC_MIPI_OVTI8856 from 2 to 1
3) define new WFC_MIPI_KBAE350 camera type as 2
- skolas specific changes:
1) remove WFC_MIPI_OVTI5675 definition (was 1)
2) redefine WFC_MIPI_OVTI8856 from 2 to 1
3) define new WFC_MIPI_KBAE350 camera type as 2
2) Add support back in for UFC_MIPI_OVTI5675 in brya0 now that FW_CONFIG
defines are fixed.
BUG=b:248126749
TEST="emerge-brya coreboot chromeos-bootimage", flash brya0 and
verify it boots successfully to kernel and that WFC, UFC, and audio
works on skolas and brya0.
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Change-Id: I3be26e0a05f4dc08e5dc3f6ef7b71bdd8fd4f859
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67929
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: YH Lin <yueherngl@google.com>
|
|
Add the RPL CPU power limits to brya0's power limit table to support
both the brya0 ADL sku and the new RPL sku.
BUG=b:248126749
TEST="emerge-brya coreboot chromeos-bootimage", flash skolas with
image-brya0.serial.bin and verify skolas boots successfully to kernel.
Change-Id: I2ac067f98f1ff8f86cff0ed0e15010f454d9c91c
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67880
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jérémy Compostella <jeremy.compostella@intel.com>
Reviewed-by: Bora Guvendik <bora.guvendik@intel.com>
Reviewed-by: Tarun Tuli <taruntuli@google.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
|
|
On newer systems such as Alder Lake it has been noticed that Intel PTT
control area is not writable until PTT is switched to ready state. The
EDK2 CRB drivers always initialize the command/response buffer address
and size registers before invoking the TPM command. See STEP 2 in
PtpCrbTpmCommand function in
tianocore/edk2/SecurityPkg/Library/Tpm2DeviceLibDTpm/Tpm2Ptp.c
Doing the same in coreboot allowed to perform PTT TPM startup
successfully and measure the components to PCRs in ramstage on an
Alder Lake S platform.
TEST=Enable measured boot and see Intel PTT is started successfully
and no errors occur during PCR extends on MSI PRO Z690-A DDR4 WIFI.
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Change-Id: Ia8e473ecc1a520851d6d48ccad9da35c6f91005d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63957
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Krystian Hebel <krystian.hebel@3mdeb.com>
|
|
The delayed return of certain fetch instruction from memory to
the UFS causes the OCP fabric to timeout on the transaction
and become non-responsive.
As recommended by the SoC and IP teams,program the
OCP fabric register to avoid the timeout in the OCP fabric.
This patch adds the following changes
1. Program the OCP fabric registers in the PS0 routine.
2. Move the ssdt contents of UFS to dsdt asl code to avoid
duplication of UFS device creation
BUG=b:240222922
TEST=Build and boot Nirwen UFS board, observe no system hang
during Chrome PLT test.
Signed-off-by: Meera Ravindranath <meera.ravindranath@intel.com>
Change-Id: I949a4538ea5c5c378a4e8ff7bb88546db1412df2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67770
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
|
|
Select the config to separate the AMDFW binary from the verified boot
section.
BUG=b:203597980
TEST=Build Skyrim BIOS image and boot to OS with PSP verstage passing
the hash table and PSP verifying the binaries against the hash table.
Observe boot time improvement of ~120 ms while operating SPI bus at 66
MHz with PSP verstage enabled.
Before this patch series:
508:finished loading body 1,978,053,432 (201,518)
After this patch series:
508:finished loading body 7,948,797,849 (83,460)
Change-Id: I78ec6d28b4c5fc40bdade47489d58180a54dee4d
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67261
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jon Murphy <jpmurphy@google.com>
Reviewed-by: Tim Van Patten <timvp@google.com>
|
|
ChromeOS requires a custom SPL table. Update Kconfig to point to the
ChromeOS version of the SPL resident in the blobs directory.
Bug=b:245727030
Test=Boots
Signed-off-by: Jon Murphy <jpmurphy@google.com>
Change-Id: I70dcb19983c970283ee887b78a18c0668e83d4b0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67928
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
MSI PRO Z690-A WIFI DDR4 and MSI PRO Z690-A DDR4 are basically the
same boards, except the latter has no WiFi populated. Check the CNVi
WiFi presence and return correct SMBIOS product name string.
TEST=Check SMBIOS product name on both WiFi and non-WiFi variants in
Linux.
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Change-Id: I5fedbce413dfb6a589a406d1e34e3e114ca6a40f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68078
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch adds the functionality to initialize the sc16is750
i2c to uart converter chip with a 14.7MHz input clock to support
115200 baud rate.
Change-Id: Ib31188b8c0f9b0ce9454da984e630eca9101d145
Signed-off-by: Husni Faiz <ahamedhusni73@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67342
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <inforichland@gmail.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
Adjust the Makefile to look for SPD source Makefile. The current
SPD guard isn't set up correctly and is attempting to build the
APCB with SPD when SPD isn't present.
BUG=b:249988439
TEST=util/abuild/abuild -x -t GOOGLE_MORTHAL --verbose
util/abuild/abuild -x -t GOOGLE_SKYRIM --verbose
util/abuild/abuild -x -t GOOGLE_WINTERHOLD --verbose
Change-Id: I9cf13acb1188309ea6a1e6bdacc37d80b01f70a8
Signed-off-by: Jon Murphy <jpmurphy@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68018
Reviewed-by: Robert Zieba <robertzieba@google.com>
Reviewed-by: Tim Van Patten <timvp@google.com>
Reviewed-by: Martin Roth <martin.roth@amd.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Copy AMD PSP fw hash table into memory, then pass it to the PSP.
The PSP will use this hash to verify it's the correct firmware bundled
with coreboot build and not replaced.
BUG=b:203597980
TEST=Build Skyrim BIOS image with the hash table and boot to OS after
PSP verified the binaries against the hash table.
Change-Id: I84bea97c89620d0388b27891a898ffde77052239
Signed-off-by: Kangheui Won <khwon@chromium.org>
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/60291
Reviewed-by: Tim Van Patten <timvp@google.com>
Reviewed-by: Jon Murphy <jpmurphy@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add build rules to separate signed PSP/AMDFW. Also add build rules to
add the generated hash table containing SHA digest of individual PSP FW
components into CBFS. This will allow verified boot to load and verify
less components from SPI rom which means faster boot time.
BUG=b:206909680
TEST=Build Skyrim with modified fmap and Kconfig
Change-Id: If54504add72b30805b6874bee562e0b9482782b9
Signed-off-by: Kangheui Won <khwon@chromium.org>
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67260
Reviewed-by: Jon Murphy <jpmurphy@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Enabling this config will put signed amd firmwares into
SIGNED_AMDFW_[AB] region which is outside FW_MAIN_[AB]. Vboot only
verifies FW_MAIN_[AB] so these regions will not be verified by vboot,
instead the PSP will verify them.
As a result we have less to load and verify from SPI rom which means
faster boot time.
BUG=b:206909680
TEST=Build Skyrim with modified fmap and Kconfig.
Change-Id: If4fd3cff11a38d82afb8c5ce379f1d1b5b9adfbf
Signed-off-by: Kangheui Won <khwon@chromium.org>
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59867
Reviewed-by: Jon Murphy <jpmurphy@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This pin was originally set as output in error. This should be
a input to behave like GPP_E16 on the older variants.
BUG=b:239721380
TEST=build
Signed-off-by: Tarun Tuli <taruntuli@google.com>
Change-Id: Ic0f793ff52adb425ae5378b88d2837bb9e58edd2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67288
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <inforichland@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
|
|
The DPTF parameters were verified by the thermal team.
BUG=b:249446156
TEST=emerge-nissa coreboot chromeos-bootimage
Signed-off-by: Ian Feng <ian_feng@compal.corp-partner.google.com>
Change-Id: Ic7e0c73815dd02b97d89f94fab09a241b6279830
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67944
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Reka Norman <rekanorman@chromium.org>
|
|
Create the lisbon variant of the brask reference board by copying
the template files to a new directory named for the variant.
(Auto-Generated by create_coreboot_variant.sh version 4.5.0).
BUG=b:246657849
BRANCH=None
TEST=util/abuild/abuild -p none -t google/brya -x -a
make sure the build includes GOOGLE_LISBON
Signed-off-by: Kevin Chiu <kevin.chiu.17802@gmail.com>
Change-Id: Ia31752765657054b28ea16b046b63c38a72f95bf
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67900
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Zhuohao Lee <zhuohao@google.com>
|
|
De-duplicate common initialization code (self-test and device
identification) and put it in a new ipmi_if.c unit, which is
supposed to work with any underlying IPMI interface.
Change-Id: Ia99da6fb63adb7bf556d3d6f7964b34831be8a2f
Signed-off-by: Sergii Dmytruk <sergii.dmytruk@3mdeb.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67056
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Krystian Hebel <krystian.hebel@3mdeb.com>
|
|
CB:67670 recently changed the format of the MRC metadata header, but
left the signature the same. That kinda defeats the purpose of having a
signature which is to make a data structure recognizable (because now
the same signature can refer to two different structures that cannot be
otherwise distinguished). While we don't know of any use case where
anything other than coreboot currently parses this data structure (other
than a ChromeOS-internal utility that's about to be removed), it's
probably better to still switch to a different signature for the new
header format just to stay on the safe side (e.g. if we ever need to
start parsing this somewhere else in the future).
CB:67670 only landed a week ago so hopefully the old signature + new
format variant hasn't had much time to escape into the wild yet.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: Ic08b23862720db832a08dc4c6818894492f43cc3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68012
Reviewed-by: Reka Norman <rekanorman@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Change-Id: I0d03bd43b33570ee50f145ea6fd716c4072a11d9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67965
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Change-Id: Ibdbd9ae90aa9683f0381d1a2458f6918ce4c0faa
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67967
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Change-Id: I9563a7f6d37937a4951c5053dcfee140579098e8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67968
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Change-Id: I4721d24aecd53c51c66c7d448b7c331d50a09712
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67972
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Change-Id: Ibc257c2306351614669bd25ac83c24475f80fc6b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67973
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
This is a vboot feature, not a ChromeOS one, and unless selected by
vboot, compilation will fail in the non-ChromeOS + vboot build case.
TEST=build/boot skyrim w/vboot, w/o ChromeOS
Change-Id: If9a5343907457bf3319f045262fdddf7eae2f1cb
Signed-off-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67995
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This is a vboot feature, not a ChromeOS one, and unless selected by
vboot, compilation will fail in the non-ChromeOS + vboot build case.
TEST=build/boot guybrush w/vboot, w/o ChromeOS
Change-Id: I3108bcc8dfeacd99c9f5d36bd915d590292fef00
Signed-off-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67994
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This area relates to storing of AP RO verification information.
CONFIG_VBOOT_GSCVD is enabled by default for TPM_GOOGLE_TI50 and
guybrush is using TPM_GOOGLE_CR50.
Signed PSP verstage has the FMAP embedded. Since CB:67376 shifted the
RO section up by 8K, they were misaligned. Hence marking this area as
unused instead of removing the same to work around ChromeOS
infrastructure shortcoming.
Signed-off-by: Himanshu Sahdev <himanshu.sahdev@intel.com>
Change-Id: Id852e5b5c1f777992a96a75143757f4df8d975b6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67901
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
It turns out that one can use Kconfig options to specify values for
devicetree options, as long as the resulting expression is a compile
time constant. Use this to configure SaGv for Atlas: enable it by
default, but allow SaGv to be disabled manually for convenience when
testing. Enabling SaGv makes MRC train the RAM multiple times, which
takes a significant amount of time.
For further info on SAGV on ADL, please refer to Intel Doc 655258
(Alder Lake Datasheet) section 5.1.3.2.
Signed-off-by: Lean Sheng Tan <sheng.tan@9elements.com>
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Change-Id: I3c6ac25d414122c408f2348d12dba8dce909e567
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67412
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
For further info on SATA test mode, please refer to this doc:
https://www.intel.com/content/dam/www/public/us/en/documents/white-papers/sata-mqst-setup-paper.pdf
Signed-off-by: Lean Sheng Tan <sheng.tan@9elements.com>
Change-Id: I6ef79fc5723348d5fd10b2ac0847191fa4f37f41
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67410
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Also add missing device/mmio.h include.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I03af0772c735cdc7a4e221770dc528724baa7523
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67983
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
|
|
Also add missing device/mmio.h include.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I0f3f7ea36896c8e55c62acd93fe8fc4fb7c74b8a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67982
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
|
|
Also include arch/mmio via device/mmio.h and not directly to have the
[read,write][8,16,32]p helper functions available.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Id8573217d3db5c9d9b042bf1a015366713d508c5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67981
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
|
|
Also include arch/mmio via device/mmio.h and not directly to have the
[read,write][8,16,32]p helper functions available.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I51c6f5c73b41546b304f16994d517ed15dbb555f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67980
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
|
|
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I6e743068dfcf9d393096f775759181af1a1c470d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67979
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
|
|
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I8445f209e43366b43b9c4750bc5f074f6d4144aa
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67978
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
|
|
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I6372741284ad5f0453f0d4dfd8ebaddd7385f8ea
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67977
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
|
|
Enable DPTC and No Battery Mode for Skyrim. This allows Skyrim to boot
without a battery or with a critically low battery.
DPTC remains disabled for the Winterhold and Morthal variants until it
can be tested on those boards.
BRANCH=none
BUG=b:217911928
TEST=Boot skyrim with low & no battery
Signed-off-by: Tim Van Patten <timvp@google.com>
Change-Id: Icc4084476916cc8e142908d8e58baf7124568b8b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67211
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change the TPM I2C freqeuncy to 1 MHz for nivviks and nereid, and in
the baseboard. Other nissa devices will be changed after verification.
This saves 11 ms of boot time on nivviks and nereid.
400 kHz:
504:finished TPM initialization 272,304 (35,730)
...
512:finished TPM PCR extend 526,250 (23,729)
513:starting locking TPM 526,250 (0)
514:finished locking TPM 535,106 (8,855)
6:end of verified boot 543,927 (8,821)
1 MHz:
504:finished TPM initialization 266,293 (30,747)
...
512:finished TPM PCR extend 513,711 (20,108)
513:starting locking TPM 513,711 (0)
514:finished locking TPM 521,311 (7,599)
6:end of verified boot 528,893 (7,581)
BUG=b:249201598
TEST=On nivviks and nereid, all timing requirements in the spec are met.
Frequencies:
nivviks - 972.01 kHz
nereid - 968.99 kHz
Change-Id: I9dd783527d4215ed7d79d69853a1f321ea2d8a28
Signed-off-by: Reka Norman <rekanorman@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67942
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kangheui Won <khwon@chromium.org>
|
|
Disable the external 1.05v VR in S0 as a fix for the
display flicker issue in ADL-N.
Please refer the Doc with ID 742988 for more details.
BUG=b:248249033, b:245970842
TEST=Verified that the display flicker issue is fixed.
Signed-off-by: V Sowmya <v.sowmya@intel.com>
Change-Id: If9f40e6c37e80caceb726a8e5f4d4b14dc479858
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67654
Reviewed-by: Vidya Gopalakrishnan <vidya.gopalakrishnan@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Reka Norman <rekanorman@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Kangheui Won <khwon@chromium.org>
|
|
Disable the external 1.05v VR in S0 as a fix for the
Display flicker issue in ADL-N.
Please refer the Doc with ID 742988 for more details.
BUG=b:248249033, b:245970842
TEST=Verified that the display flicker issue is fixed.
Signed-off-by: V Sowmya <v.sowmya@intel.com>
Change-Id: Iaa53bfd99a550b2cffcdaee640ee3a429e93aef7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67653
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Vidya Gopalakrishnan <vidya.gopalakrishnan@intel.com>
Reviewed-by: Reka Norman <rekanorman@chromium.org>
Reviewed-by: Kangheui Won <khwon@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Commit c7204b5a4 [mb/google/guybrush: Enable backlight in the OS]
disabled the GPIO for the display backlight in favor of using ACPI
to enable it, but this breaks display output for payloads which do
not/can not enable the backlight GPIO themselves (edk2, grub, SeaBIOS).
Re-enable the GPIO for display backlight so that payloads other than
depthcharge work properly.
TEST=build/boot google/dewatt with Tianocore payload, verify payload
display visible.
Change-Id: I2519d779954ed89486045aa7de0b18f1c31a4374
Signed-off-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67246
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martin.roth@amd.corp-partner.google.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Example for Alder Lake PTT:
Handle 0x004C, DMI type 43, 31 bytes
TPM Device
Vendor ID: INTC
Specification Version: 2.0
Firmware Revision: 600.18
Description: Intel iTPM
Characteristics:
TPM Device characteristics not supported
OEM-specific Information: 0x00000000
TEST=Execute dmidecode and see the type 43 is populated with PTT
on MSI PRO Z690-A WIFI DDR4
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Change-Id: I05289f98969bd431017aff1aa77be5806d6f1838
Reviewed-on: https://review.coreboot.org/c/coreboot/+/64049
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Christian Walter <christian.walter@9elements.com>
|
|
Based on DMTF SMBIOS Specification 3.1.0.
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Change-Id: Ia2db29f8bc4cfbc6648bb2cabad074d9ea583ca9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/64048
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Christian Walter <christian.walter@9elements.com>
|
|
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Change-Id: Ie564d080955097b416943e772de6c62708ce5764
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67971
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
use is_enabled_cpu() on cycles over device list to check
whether the current device is enabled cpu.
TEST: compile test and qemu run successfully with coreinfo
payload
Signed-off-by: Fabio Aiuto <fabioaiuto83@gmail.com>
Change-Id: If64bd18f006b6f5fecef4f606c1df7d3a4d42883
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67797
Reviewed-by: Tim Wawrzynczak <inforichland@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Add function defs and prototypes of functions checking whether
a device is {a cpu,an enabled cpu}
TEST: compile test and qemu executed successfully with
coreinfo payload
Signed-off-by: Fabio Aiuto <fabioaiuto83@gmail.com>
Change-Id: Iabc0e59d604ae4572921518a8dad47dc3d149f81
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67502
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Change-Id: Ic0361e5d928c24cfe7dc0a8b0385fbe73d906b15
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62365
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Petr Cvek <petrcvekcz@gmail.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Fix the warning below when building GA-945GCM-S2L with 64-bit:
src/arch/x86/idt.S:216: Warning: no instruction mnemonic suffix given and no register operands; using default for `iret'
Change-Id: Ibbc106714e25293951a71d84fea0a660f41f9c02
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61336
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
This patch de-selects EC software sync config and enable early
EC Software Sync.
BUG=b:248775521
TEST=Able to perform EC sync on Google/Rex.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I6bf8018e8a3fd06bb98c82a27d12883fc8d3a5db
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67817
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tarun Tuli <taruntuli@google.com>
|
|
Rename so table more indicative of when GPIOs are set, and so it can
be used for more than just setting PCIe GPIOs.
Rename the getter function to match.
Change-Id: I285602209072247895c2cb0830f3faf675328757
Signed-off-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67810
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Rename variant_base_gpio_table() to baseboard_gpio_table(), since the
GPIO table comes from the baseboard, and is overridden by a separate
table from the variant.
Drop the __weak qualifier as this function is not overridden.
Change-Id: Icebf7e11736929389227063039575a4c5ecf3840
Signed-off-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67809
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
This patch adds ACPI configurations of 8MP YHUX and 2MP CJFKF28-1
as world- and user-facing cameras of Rex.
BUG=b:246413264
TEST=Verified world- and user-facing cameras using Chrome Camera App on
Google/rex device.
Signed-off-by: Daniel Kang <daniel.h.kang@intel.com>
Change-Id: Iaaa16e491a66500606b3a9eb1d87f396641778e0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67085
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tarun Tuli <taruntuli@google.com>
|
|
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Change-Id: Ib2c1738b7b6a6db1fa57ea34fb50588388140a51
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67911
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
|
