| Age | Commit message (Collapse) | Author |
|---|
|
Commit 16ab9bdcd578612bb3822373547f939eb90afd82 ("soc/intel/common:
Calculate and configure SF Mask 2") breaks the computation of the
number of ways and as result, all the derived masks. It results in MSR
such as `IA32_L3_MASK_1' to be improperly programmed yielding
unpredictable NEM issues such as hangs.
Indeed, this commit has introduced a backup of 0x1 into %edx before
comparing the requested cache-as-RAM size against the way size. When
the requested cache-as-RAM is larger, it reaches the second part of
the algorithm which computes the necessary number of ways to fit the
requested cache-as-RAM.
This algorithm uses the `div' instruction. Per specification, the div
instruction divides the 64 bits combination of %edx and %eax register.
Since 0x1 got backed up in %edx and assuming a
`CONFIG_DCACHE_RAM_SIZE' of 0x200000, we end up dividing 0x100200000
by the way size instead of 0x200000 which result in a necessary number
of ways of 4098 for a way size of 0x100000.
This commit clears the %edx register before calling the `div'
instruction.
BUG=b:360332771
TEST=Verified on PTL Intel reference platform
Change-Id: I5cb66da0aa977eecb64a0021268a6827747c521d
Signed-off-by: Jeremy Compostella <jeremy.compostella@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/83948
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Intel's PMC CrashLog size in legacy mode is expressed in DWORDs and
therefore needs to be explicitly recalculated to bytes.
BUG=None
TEST=Built and checked the size in logs
Change-Id: I2678d537439c24fbd10aa3ceffee63c9a849d28b
Signed-off-by: Jędrzej Ciupis <jciupis@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/83883
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jakub Czapiga <czapiga@google.com>
|
|
The power off code in depthcharge disables all GPEs prior to power off.
The problem is that for gpio wake sources that are locked, this power
off code cannot successfully clear any pending interrupt from that
source. This can result in the device incorrectly waking back up after
it's been powered off from the firmware dev screen.
BUG=b:360380950, b:359692570
BRANCH=None
TEST=verify brox DUT is able to power down and stay powered down when
selecting the "Power off" button in the firmware dev screen.
Change-Id: I5cd36640677996209beb8fe29f522ff8e07ebf00
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/83951
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <ericllai@google.com>
|
|
The power off code in depthcharge disables all GPEs prior to power off.
The problem is that for gpio wake sources that are locked, this power
off code cannot successfully clear any pending interrupt from that
source. This can result in the device incorrectly waking back up after
it's been powered off from the firmware dev screen.
BUG=b:360380950, b:359692570
BRANCH=None
TEST=verify rex DUT is able to power down and stay powered down when
selecting the "Power off" button in the firmware dev screen.
Change-Id: I3fdc02a82d197fd2b075e0a66c578149cef3a69f
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/83950
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Eric Lai <ericllai@google.com>
|
|
The power off code in depthcharge disables all GPEs prior to power off.
The problem is that for gpio wake sources that are locked, this power
off code cannot successfully clear any pending interrupt from that
source. This can result in the device incorrectly waking back up after
it's been powered off from the firmware dev screen.
BUG=b:360380950, b:359692570
BRANCH=firmware-brya-14505.B
TEST=verify brask, nissa, or brya DUT is able to power down and stay
powered down when selecting the "Power off" button in the firmware dev
screen.
Change-Id: Ic0ac73f8f29761f072d42f35e97198b56d32a9bc
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/83949
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Eric Lai <ericllai@google.com>
|
|
This patch replaces the SoC-specific config option
`SOC_INTEL_PANTHERLAKE_DEBUG_CONSENT` with the generic
`SOC_INTEL_COMMON_DEBUG_CONSENT`.
TEST=Able to build and boot google/fatcat without any functional impact
while debugging.
Change-Id: I36bbe14d02654ed9dbda21df0d9a6a6769b87754
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/83962
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Dinesh Gehlot <digehlot@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch replaces the SoC-specific config option
`SOC_INTEL_METEORLAKE_DEBUG_CONSENT` with the generic
`SOC_INTEL_COMMON_DEBUG_CONSENT`.
Additionally, updates the FSP configuration to use the new generic
config option.
TEST=Able to build and boot google/rex0 without any functional impact
while debugging.
Change-Id: I657d20a38e15eee333a4e45c0c600736148173d4
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/83961
Reviewed-by: Dinesh Gehlot <digehlot@google.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch replaces the SoC-specific config option
`SOC_INTEL_ALDERLAKE_DEBUG_CONSENT` with the generic
`SOC_INTEL_COMMON_DEBUG_CONSENT`.
Additionally, updates the FSP configuration to use the new generic
config option.
TEST=Able to build and boot google/redrix without any functional impact
while debugging.
Change-Id: I9a9c81b72d707f5ed2e1a53c139ee22be0e30068
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/83957
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Dinesh Gehlot <digehlot@google.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
This patch drops the SoC-specific config option
`SOC_INTEL_TIGERLAKE_DEBUG_CONSENT`.
Additionally, updates the FSP configuration to use the new generic
config option.
TEST=Able to build and boot google/volteer without any functional
impact while debugging.
Change-Id: I3e96b20e7e8b3ce3c2e4884abd315a5cc55fe71d
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/83963
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
This patch drops the SoC-specific config option
`SOC_INTEL_JASPERLAKE_DEBUG_CONSENT`.
Additionally, updates the FSP configuration to use the new generic
config option.
TEST=Able to build and boot google/dedede without any functional
impact while debugging.
Change-Id: I3e7abaf5fb3a0d5528041af5ce767a15fc738870
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/83960
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch drops the SoC-specific config option
`SOC_INTEL_ELKHARTLAKE_DEBUG_CONSENT`.
Additionally, updates the FSP configuration to use the new generic
config option.
TEST=Able to build and boot intel/elkhartlake_crb without any
functional impact while debugging.
Change-Id: Idb8db7230c432792e742218d41d891c529b2114f
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/83959
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch drops the SoC-specific config option
`SOC_INTEL_CANNONLAKE_DEBUG_CONSENT`.
Additionally, updates the FSP configuration to use the new generic
config option.
TEST=Able to build and boot google/hatch without any functional impact
while debugging.
Change-Id: Ifad11652b5fa6ff14f713f55a721cdbbfbfde471
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/83958
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
With commit 26b1a5f62b ("mb/acer/g43t-am3: Rework mainboard for variant
mechanism"), the files related to the G43T-AM3 mainboard were supposed
to be moved into its own variant directory. However, it seems it was
forgotten to delete the old ones and thus remove the duplicates.
Change-Id: I450fab074621d21e80216e4667eaf2510b0e14ad
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/83985
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This board now uses merlin so it can be removed.
Change-Id: I6036695ccf80b0a7d6e6463d26e5b32aa6cb9d57
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/83630
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
|
|
Remove the ITE mirror functionality; all devices will mirror
automatically when they exit G3, and this is good enough.
Change-Id: I9b82e1b1386b4607dfe7da9b25ba432ec0303cf8
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/83629
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This properly supports power_on_after_fail setting on affected
mainboards.
Tested on GA-H61M-S2PV
Change-Id: I3dcc4f032bc5f629fb916c4122beb8dc096bab20
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82737
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Change-Id: I15dfd5ed0541352930c3b70252b3e536ad1e6efd
Signed-off-by: Michael Strosche <michael.strosche@gmail.com>
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77374
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
|
|
Previously RAM probing was necessary for our QEMU-RISCV target in order
to find the available amount of memory.
Now we get the memory from the devicetree propagated by QEMU, so there
is no reason to keep it anymore.
Tested:
Start QEMU-RISCV and cause an exception to make sure the trap handler
still works.
Signed-off-by: Maximilian Brune <maximilian.brune@9elements.com>
Change-Id: I9b1e0dc78fc2a66d6085fe99a71245ff46f8e63c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/83873
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch adds a generic config option, SOC_INTEL_COMMON_DEBUG_CONSENT,
to control the debug interface on Intel SoCs. This eliminates the need
for SoC-specific config options like SOC_INTEL_<SOC_NAME>_DEBUG_CONSENT.
Default values are provided for various debug types:
- 0: Disabled
- 1: Enabled (DCI OOB + [DbC])
- 2: Enabled (DCI OOB)
- 3: Enabled (USB3 DbC)
- 4: Enabled (XDP/MIPI60)
- 5: Enabled (USB2 DbC)
- 6: Enabled (2-wire DCI OOB)
- 7: Manual
Specific SoCs can override the SOC_INTEL_COMMON_DEBUG_CONSENT value
using SoC config override methods.
TEST=Able to build google/rex.
Change-Id: I84ad03f0ffe5da4bc53c665489c430fe9b65ede7
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/83956
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <ericllai@google.com>
|
|
This patch selects the SOC_INTEL_COMMON_BASECODE option for Elkhart
Lake so that future patches can incorporate the common code debug
feature with it.
TEST=Able to build the EHL platform.
Change-Id: I71d95352fe627a7f1912f802aa971ad1ebbbead7
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/83955
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Adjust settings as recommended by thermal team.
Set tcc_offset value to 12 in devicetree.
BUG=b:308704811
BRANCH=firmware-rex-15709.B
TEST=emerge-ovis coreboot chromeos-bootimage
built bootleg and verified test result by thermal team
Change-Id: I0ae97bb0b2dbb2fe8f35221522506ec1f7da47f6
Signed-off-by: Tony Huang <tony-huang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/83971
Reviewed-by: Derek Huang <derekhuang@google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
To publish the Bluetooth Regulator Domain Settings under the right
ACPI device scope, the wifi generic driver requires the bluetooth
companion to be set accordingly.
BUG=b:345596420
TEST=Build and test on revin, check BRDS is shown in SSDT.
Change-Id: I87cfbdd0b8a97d84a96af373855219c60f39f173
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/83944
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: V Sowmya <v.sowmya@intel.com>
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Dinesh Gehlot <digehlot@google.com>
|
|
To publish the Bluetooth Regulator Domain Settings under the right
ACPI device scope, the wifi generic driver requires the bluetooth
companion to be set accordingly.
BUG=b:345596420
TEST=Build and test on nivviks, check BRDS is shown in SSDT.
Change-Id: Ib654f22033c68edbc602f14537aaa2151800598d
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/83943
Reviewed-by: Dinesh Gehlot <digehlot@google.com>
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: V Sowmya <v.sowmya@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch adds SoundWire driver to support ALC722 audio codec.
The existing ALC711 codec driver is refactored to include support for
ALC722 device based on config flag.
The ACPI address for the codec is calculated with the information in
the codec driver combined with the devicetree.cb hierarchy where the
link and unique IDs are extracted from the device path.
For example this device is connected to master link ID 0 and has strap
settings configuring it for unique ID 1:
chip drivers/soundwire/alc711
register "desc" = ""Headset Codec""
device generic 0.1 on end
end
reference datasheet: Realtek ALC722-CG ver. 0.56
TEST=This driver was tested on Intel RVP with on board ALC722 codec
by booting and disassembling the runtime SSDT to ensure that the
devices have the expected address and properties. Test soundcard
binding works and devices are detected and check for audio playback
using speaker output.
Signed-off-by: Anil Kumar <anil.kumar.k@intel.com>
Change-Id: Ieb16a1c6f3a79321fdc35987468daa8be33b6e49
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81920
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
EFI System Resource Table (ESRT) is an informational structure that
reports basic details about current system or device firmware. This is
chiefly used to perform firmware updates.
New CONFIG_DRIVERS_EFI_FW_INFO is off by default, enabling it adds
DRIVERS_EFI_FW_{GUID,VERSION,LSV} to be used to specify firmware
version/update information.
Existing forms of versions wouldn't be sufficient because there is no
universal way of converting string versions to 32-bit unsigned integers
and there are no GUIDs or lowest supported versions.
Change-Id: Ic1b768d7bed43edf7ca8e41552087734054de033
Signed-off-by: Sergii Dmytruk <sergii.dmytruk@3mdeb.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/83421
Reviewed-by: Christian Walter <christian.walter@9elements.com>
Reviewed-by: coreboot org <coreboot.org@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change STORAGE_UNPROVISIONED to STORAGE_UNKNOWN depend on depthcharge setting.
BUG=None
TEST=emerge-brox coreboot
Set STORAGE_UNKNOWN on jubilant, check that NVMe and UFS can boot.
Change-Id: I4cfd7322c2940862dfbae46e85522715cd7534c1
Signed-off-by: Morris Hsu <morris-hsu@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/83935
Reviewed-by: Ren Kuo <ren.kuo@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: YH Lin <yueherngl@google.com>
Reviewed-by: Bob Moragues <moragues@google.com>
|
|
Before:
I2C2 - 431KHz
I2C4 - 413KHz
After:
I2C2 - 364KHz
I2C4 - 370KHz
BUG=b:351968527
TEST=Rate of the actual measured machine is pass.
Change-Id: Ieb75db1dc95ffd5ca806a194ae678c700fa0741c
Signed-off-by: Wei Hualin <weihualin@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/83906
Reviewed-by: Eric Lai <ericllai@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Weimin Wu <wuweimin@huaqin.corp-partner.google.com>
|
|
Set up soundbar-related GPIOs for updating.
BUG=b:358435383
TEST=emerge-constitution coreboot chromeos-bootimage
Change-Id: I517da8de90487533e49e46649c5acf4ccfcc5160
Signed-off-by: Kenneth Chan <kenneth.chan@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/83936
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Eric Lai <ericllai@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch changes the strnlen() implementation to fix a small issue
where we would dereference once more byte than intended when not finding
a NUL-byte within the specified amount of characters. It also changes
the implementation to rely on a pre-calculated end pointer rather than a
running counter, since this seems to lead to slightly better assembly
(one less instruction in the inner loop) on most architectures.
Change-Id: Ic36768fd3a26e2b64143904e78cd0b52ba66898d
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/83933
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
This patch removes WWAN configuration from the bootblock.
It appears that setting it up in the bootblock may not be necessary.
Configure in bootblock,the seq will be triggered at the same time.
The customer would like us to leave some buffer for EN to RST.
BUG=b:357764679
TEST=Build and verified test result by EE team
Change-Id: I2c0e789c0bec293f4bca711e53644d62f4f83551
Signed-off-by: Roger Wang <roger2.wang@lcfc.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/83792
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Dinesh Gehlot <digehlot@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Since commit 1d029b40c9de ("lib/jpeg: Replace decoder with Wuffs'
implementation"), a relatively large heap allocation is needed to decode
many JPEGs for use as work area. The prior decoder did not need this,
but also had many limitations in the JPEGs it could decode, was not as
memory-safe and quickly crashed under fuzzing.
This commit keeps using Wuffs' JPEG decoder, but it no longer requires
any heap allocation (and thus configuring the heap size depending on how
big a bootsplash image you want to support).
Change-Id: Ie4c52520cbce498539517c4898ff765365a6beba
Signed-off-by: Nigel Tao <nigeltao@golang.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/83895
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Reviewed-by: Jonathon Hall <jonathon.hall@puri.sm>
|
|
We were previously at Wuffs 0.4.0-alpha.2. The C file was copied from
https://github.com/google/wuffs-mirror-release-c and its hash matches
https://github.com/google/wuffs-mirror-release-c/blob/90e4d81a6a8b7b601e8e568da32a105d7f7705e5/sync.txt#L9-L10
$ sha256sum src/vendorcode/wuffs/wuffs-v0.4.c
6c22caff4af929112601379a73f72461bc4719a5215366bcc90d599cbc442bb6 src/vendorcode/wuffs/wuffs-v0.4.c
Change-Id: Ie90d989384e0db2b23d7d1b3d9a57920ac8a95a2
Signed-off-by: Nigel Tao <nigeltao@golang.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/83894
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This adds a new board as a variant of the Acer G43T-AM3 with the
following prominent changes:
* Intel Q45 northbridge (GMCH) instead of a G43
* 4 MiB of flash instead of 2 MiB
* Two serial ports (one external, one internal)
* A parallel port connector (internal)
* An FDD connector
* DVI-D instead of HDMI
* No Firewire
The port was done based on logs and info received via private email. It
was only tested on the Acer G43T-AM3 so far, which still builds and works.
Change-Id: Ic2654ca4b198bfea409992be14e89702cf67ea50
Signed-off-by: Julia Kittlinger <launchpad.vineyard395@passinbox.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/83968
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
|
|
In preparation for CB:83968, rework the configuration files and move
files specific to G43T-AM3 to its own variant directory.
Change-Id: I425852f4bdacf7cb6688a5fb845ac3001373262e
Signed-off-by: Michael Büchler <michael.buechler@posteo.net>
Signed-off-by: Julia Kittlinger <launchpad.vineyard395@passinbox.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57764
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch calls `xhci_host_reset()` function to perform XHCI
controller reset.
Currently, the PMC IPC times out while sending the USB-C (0xA7) command
during poweron from S5 (S5->S4->S3->S0).
On Brya variants, poweron from S5 state results in PMC error while
sending PMC IPC (0xA7) to USB-C active ports, log here:
localhost ~ # cbmem -c | grep ERROR
[ERROR] PMC IPC timeout after 1000 ms
[ERROR] PMC IPC command 0x200a7 failed
[ERROR] pmc_send_ipc_cmd failed
[ERROR] Failed to setup port:0 to initial state
[ERROR] PMC IPC timeout after 1000 ms
[ERROR] PMC IPC command 0x200a7 failed
[ERROR] pmc_send_ipc_cmd failed
[ERROR] Failed to setup port:1 to initial state
[ERROR] PMC IPC timeout after 1000 ms
[ERROR] PMC IPC command 0x20a0 failed
This problem is not seen while powering on from G3 (G3->S5->S4->S3->S0).
During poweron the state of USB ports are not the same between S5 and G3
and it appears that the active USB port still is in U3 (suspend) while
PMC tries to send the IPC command, which results in a timeout.
This patch utilises the S5 SMI handler to reset the XHCI controller
using `xhci_host_reset()` prior entering into the S5, it helps to
restore the port state to active hence, no PMC timeout is seen with
this code change.
Supporting Doc=Intel expected to release a TA (Technical Advisory)
document to acknowledge this observation and supported W/A for ADL
generation platforms.
Till that time, keeping this W/A as part of the google/brya specific
mainboard alone.
Note: other ADL-SoC based mainboards might need to apply the similar
W/A.
BUG=b:227289581
TEST=No PMC timeout is observed while sending USB-C PMC command (0xA7)
during resume from S5.
Total Time: 1,045,855
localhost ~ # cbmem -c | grep ERROR
No PMC timeout error is observed with this CL.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: Ibf06a64f055a0cee3659b410652082f31e18e149
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63552
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
|
|
Recently merged commit 8cc1d79ed0c3 (mainboard/qemu-aarch64: Get top
of memory from device-tree blob) missed a rebase and hence needs the
include path updated.
Tested `make qemu` for qemu-aarch64.
Change-Id: Id669eeaabbc1710bb7e408659f2d79f682427919
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/83945
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
|
|
Trying to probe RAM space to figure out top of memory causes an
exception on AArch64 virtual machines with recent versions of QEMU, but
we temporarily enable exception handlers for that and use it to help
detect if a RAM address is usable or not. However, QEMU docs recommend
reading device information from the device-tree blob it provides us at
the start of RAM.
A previous commit adds a library function to parse device-tree blob that
QEMU provides us. Use it to determine top of memory in AArch64 QEMU
virtual machines, but still fall back to the RAM probing approach as a
last-ditch effort.
Change-Id: I4cc888b57cf98e0797ce7f9ddfa2eb34d14cd9c1
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80364
Reviewed-by: Maximilian Brune <maximilian.brune@9elements.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
List of changes:
1. Add required SoC programming till romstage
2. Include only required headers into include/soc
3. Fill required FSP-M UPD to call FSP-M API
4. Ref: Processor EDS documents
Panther Lake U/H 12Xe/H 4Xe External Design
Specification (EDS) Rev. 0.7, vol 1 of 2 #815002 and
Volume 2 of 2 #813030
BUG=b:348678529
TEST=Verified on Intel® Simics® Pre Silicon Simulation platform
for PTL using google/fatcat mainboard.
Change-Id: I27e1a6c56bca01e7f5f53fbf3cb6855bac7b2848
Signed-off-by: Saurabh Mishra <mishra.saurabh@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/83635
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jamie Ryu <jamie.m.ryu@intel.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
1.Set unused device's GPIOs to NC based on fw_config.
2.Disable config for nvme, ufs and CNVi based on fw_config.
3.Add fw_config STORAGE_UNKNOWN to enable all storages
for the first boot in factory.
BUG=None
TEST=emerge-brox coreboot chromeos-bootiamge
check fw_config messages in ap log
verify devices on/off by fw_config on jubilant
Change-Id: I8d9f4edea454e0861f91261bf13fa80572d0a181
Signed-off-by: Morris Hsu <morris-hsu@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/83874
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Ren Kuo <ren.kuo@quanta.corp-partner.google.com>
|
|
Locking GPP_F15 causes DUTs with fingerprint sensor to not be able to
correctly power down and stay powered down. This pin does not need to
be locked.
BUG=b:359692570, b:356750516
BRANCH=firmware-brya-14505.B
TEST=`FW_NAME=gimble emerge-brya coreboot chromeos-bootimage`, flash and
boot gimble into developer mode, then reboot into dev screen and select
the "Power off" button and verify gimble powers off and does not power
itself back up.
Change-Id: I1c73035b02021b0d1268cd46dcd0841621556ad5
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/83932
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The AP console log contains "HECI: No CSE device" and the system cannot be entered.
BUG=b:359474142
TEST=abuild -v -a -x -c max -p none -t google/dedede -b awasuki
The "HECI: No CSE device" message for AP log disappered
Change-Id: I488056dc8bca2174dd96c28793e3202b7aae890c
Signed-off-by: Weimin Wu <wuweimin@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/83905
Reviewed-by: Tongtong Pan <pantongtong@huaqin.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
This reverts commit 2eb5c1e83ef5206f384846d7514c3aebcaec5bb8.
Reason for revert: The latest release of FSP will not boot
without a display being connected using this VBT. The original
VBT does not have this issue, nor is the original issue that
commit 2eb5c1e83ef5206f384846d7514c3aebcaec5bb8 fixed.
Revert it to restore booting when there is no display.
Change-Id: I05f9037cd68b8b29e69156e2372a544985f4442e
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/83893
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
|
|
Both AGESA.h and cpu/amd/mtrr.h defined TOP_MEM and TOP_MEM2, but since
it was defined as unsigned long in AGESA.h, a workaround was needed in
cpu/amd/mtrr.h to not have the build fail due to a non-identical
redefinition of TOP_MEM and TOP_MEM2. Just removing the workaround
without reaming the defines isn't trivially possible, since the
stoneyridge romstage.c still ends up including both definitions which
can't be easily worked around. Now all non-vendorcode coreboot code uses
TOP_MEM_MSR and TOP_MEM2_MSR while the vendorcode part uses TOP_MEM and
TOP_MEM2 to avoid this.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ibad72dac17bd0b05734709d42c6802b7c8a87455
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74619
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martin.roth@amd.corp-partner.google.com>
|
|
Replace 'is_domain0(dev_get_domain(dev))' with 'is_dev_on_domain0(dev)'
which is a helper function that does exactly the same, but slightly
simplifies the call.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I8b0c52a9176288039e6414a09c3fe0662db79e4b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/83908
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Shuo Liu <shuo.liu@intel.com>
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
|
|
When `maxlen` is large (such as SIZE_MAX), the `end` pointer will
overflow, causing strnlen() to incorrectly return 0.
To not make the implementation over-complicated, fix the problem by
using a counter.
BUG=b:359951393
TEST=make unit-tests -j
BRANCH=none
Change-Id: Ic9d983b11391f5e05c2bceb262682aced5206f94
Signed-off-by: Yu-Ping Wu <yupingso@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/83914
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
|
|
The previous implementation incorrectly assumed that the presence of a
UFS device implied the availability of the ISH partition. This is not
always true, especially on Alder Lake platforms where ISH may be
enabled by default even without UFS.
This patch fixes the issue by directly checking for the presence of the
ISH device to determine if the ISH partition is available.
BUG=b:359440547
TEST=1. Able to dump the ISH version with UFS device:
```
tirwen-rev3 ~ # cbmem -c -1 | grep ISH
[DEBUG] ISH version: 5.4.2.7780
```
2. Able to dump the ISH version with eMMC device:
```
trulo-rev1 ~ # cbmem -c | grep ISH
[DEBUG] ISH version: 5.4.2.7780
```
Change-Id: I411e36606c0697f91050af40e0636f7c64810e95
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/83898
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Dinesh Gehlot <digehlot@google.com>
Reviewed-by: Eric Lai <ericllai@google.com>
|
|
Extracted from coreboot-Google_Phaser.11297.296.0.bin.
Fixes display init on newer LASER14 boards.
TEST=build/boot google/phaser, observe display init successful.
Change-Id: Icb48edb4e74f147e3458f845d921a15a2d1906da
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/83897
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
If a root port doesn't use a clock request pin, we shouldn't check if
this pin number, which defaults to 0 when not set, is already used. This
fixes the following spurious warning that was previously printed for
each external PCIe port which has the 'PCIE_RP_CLK_REQ_UNUSED' flag set
and didn't set 'clk_req' to some unused clock request pin number:
Found overlapped clkreq assignment on clk req 0
Tested on the cw-al-4l-v2.0 mainboard that uses an Alder Lake N100 SoC
which I'm currently porting coreboot to. Also changing this for Meteor
Lake, since they have the same implementation in their romstage
fsp_params.c file
Change-Id: I3ee66ca5ed5a2d06dfb68c45a50e11eb2b93daa0
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/83865
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-by: Maximilian Brune <maximilian.brune@9elements.com>
|
|
In next phase, riven will remove external fivr. Use the board version
to config external fivr for backward compatibility and show message.
BUG=b:359062365
TEST=build, boot to OS, suspend/resume work normally.
Change-Id: Id5f538b2eda7820a922b8d9ee14b2bae7df3726c
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/83891
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Eric Lai <ericllai@google.com>
|
|
Brox does not have PCIe WWAN or discrete GPU. Hence no need to power
them off during suspend. Hence also remove the MPTS ACPI method.
BUG=None
TEST=Build Brox firmware and boot to OS.
Change-Id: Ia239c3f038ce31934efb0a391350fa0f786e3fcd
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/83788
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
An upcoming vboot feature [1] will need strcat() to be defined in
string.h. Therefore, add strcat() and strncat() to commonlib/bsd. Remove
those functions from libpayload.
[1] https://chromium-review.googlesource.com/c/chromiumos/platform/vboot_reference/+/5650810
Change-Id: If02fce0eafb4f6fa01d8bab17d87a32360f4ac83
Signed-off-by: Yu-Ping Wu <yupingso@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/83765
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
Add strlen() and strnlen() to commonlib/bsd by rewriting them from
scratch, and remove the same functions from coreboot and libpayload.
Note that in the existing libpayload implementation, these functions
return 0 for NULL strings. Given that POSIX doesn't require the NULL
check and that other major libc implementations (e.g. glibc [1]) don't
seem to do that, the new functions also don't perform the NULL check.
[1] https://github.com/bminor/glibc/blob/master/sysdeps/i386/strlen.c
Change-Id: I1203ec9affabe493bd14b46662d212b08240cced
Signed-off-by: Yu-Ping Wu <yupingso@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/83830
Reviewed-by: Maximilian Brune <maximilian.brune@9elements.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
Brox uses Ti50 which always supports long interrupt pulse. Hence no need
to override GPIO PM.
BUG=None
TEST=Build Brox firmware and boot to OS. Perform suspend/resume for 25
cycles.
Change-Id: I6a138c1953714bc29570db587594cab8f315a4ec
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/83856
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch updates the platform-specific Meteor Lake early
sign-of-life config (SOC_INTEL_METEORLAKE_SIGN_OF_LIFE) with a generic
ChromeOS eSOL config (CHROMEOS_ENABLE_ESOL) which uses the Intel FSP
uGOP driver as an underlying technology for rendering eSOL screen.
This patch does not change the binary or the system behaviour.
BUG=b:352651132
TEST=Able to build google/rex and checked the config in output.
Change-Id: Ib4589f52080229b1c83915b51272a042b7ac32cd
Signed-off-by: Jayvik Desai <jayvik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/83769
Reviewed-by: Dinesh Gehlot <digehlot@google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch updates the early libgfx init config
(MAINBOARD_HAS_EARLY_LIBGFXINIT) used for Alder Lake SoC with a
generic CrOS/ChromeOS early sign of life config (CHROMEOS_ENABLE_ESOL)
This patch does not change the binary or the system behaviour and is
only meant to bind the early GFX initialization with a generic eSOL
config.
BUG=b:352651132
TEST=Able to build google/tivviks and checked the config in output
Change-Id: Ibc1b9190ac0e4d25f3c5517d74c9b519bc3bb349
Signed-off-by: Jayvik Desai <jayvik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/83841
Reviewed-by: Dinesh Gehlot <digehlot@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
This patch introduces a new early sign-of-life config option when
libgfx or uGOP is enabled for early graphics initialization.
BUG=b:352651132
TEST=Able to build google/rex and google/tivviks
Change-Id: Ic8fe4ca5234de7f8e579f950f6ccbf750f4c7950
Signed-off-by: Jayvik Desai <jayvik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/83705
Reviewed-by: Dinesh Gehlot <digehlot@google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch enables the TCSS XHCI in the devicetree to solve the genesys
hub enumeration issue.
BUG=b:348332200
TEST=Able to build google/nova and ensure lsusb can list genesys
hub device.
Change-Id: Ic8e25756a2975e884434c4c7e3d587f4c1f0ed0b
Signed-off-by: Pranava Y N <pranavayn@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/83845
Reviewed-by: Dinesh Gehlot <digehlot@google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Eric Lai <ericllai@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This change includes the <stdint.h> header file to resolve the
compilation error "'SIZE_MAX' undeclared". This issue was introduced
by commit hash af0d4bce65df277b56e495892dff1c712ed76ddd (region:
Introduce region_create() functions).
TEST=Able to build google/rex.
Change-Id: I0dbd839e3573d5c74375911903c8f9d6a66bbf28
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/83886
Reviewed-by: Jakub Czapiga <czapiga@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Confirm with EE, the GPP_C1 don't need PU 20K.
So modify GPP_C1 setting to remove PU 20k
Schematic version: 500E_GEN4S_ADL_N_MB_0418
BUG=b:358162951
TEST=Build and boot on pujjoga.
Change-Id: I7ad16cd29ab467d3eac74dab40522c577d91c747
Signed-off-by: Leo Chou <leo.chou@lcfc.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/83818
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Derek Huang <derekhuang@google.com>
Reviewed-by: Eric Lai <ericllai@google.com>
|
|
1. The P sensor need follow WWAN FW_CONFIG to enable/disable
2. Modify GPP_H19 setting to PAD_CFG_GPI_APIC to fix PLT test fail
Schematic version: 500E_GEN4S_ADL_N_MB_0418
BUG=b:357998089
TEST=1. Boot to OS and verify the P sensor devices is set based on
fw_config.
2. Confirm that the PLT test can pass successfully.
Change-Id: Ic3610180c8cf99eba9367e26bfc3666410af19f7
Signed-off-by: Leo Chou <leo.chou@lcfc.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/83794
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
This change adds the necessary configuration for the elan
touchscreen (ELAN9004) device, connected to I2C bus 16.
It includes settings for:
* HID descriptor
* Device description
* IRQ configuration
* Detection
* Reset, stop and enable GPIOs with their respective delays
* Power resource handling
* HID descriptor register offset
BUG=b:348125053 b:348126380
TEST=emerge-nissa coreboot
boot with elan TS, make sure elan TS is functional.
Change-Id: I64c5a11dfaacfcca34240375d4dca5c76a60f62e
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/83876
Reviewed-by: Eric Lai <ericllai@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
Turn on DRAM_LED on the mainboard in early bootblock, and turn it off
in ramstage. Primarily an indication if boot fails during raminit,
modeled after vendor firmware.
This LED is controlled by GPIO07 on the super I/O.
Boot tested on hardware.
Change-Id: I549b51375d1ef056d5fc01871bfe62d60b8a01cb
Signed-off-by: Keith Hui <buurin@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81890
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
|
|
This patch introduces a new configuration option,
FSP_UGOP_EARLY_SIGN_OF_LIFE, to the FSP driver. This enables uGOP
support using FSP-M for the early sign-of-life feature in SOC.
BUG=NA
TEST=Able to build google/rex and checked the config in output.
Change-Id: Ic0426ff7974a141ae9188b0098677b4cc97aee36
Signed-off-by: Jayvik Desai <jayvik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/83770
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Dinesh Gehlot <digehlot@google.com>
|
|
Change-Id: I27568d1205216f697b48ffb09ce5208505718978
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/83863
Reviewed-by: Dinesh Gehlot <digehlot@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Remove the unused config VPD from GNR Kconfig.
Change-Id: I3fc45ba05df5fc23e326081d6ce9e53b2046464c
Signed-off-by: Gang Chen <gang.c.chen@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82975
Reviewed-by: Martin L Roth <gaumless@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Shuo Liu <shuo.liu@intel.com>
|
|
List of changes:
1. Add required Pather Lake SoC programming till bootblock.
2. Include only required headers into include/soc.
3. Include PTL related DID, BDF.
4. Includes additional minimal code required to compile the PTL SoC
and google/fatcat mainbaord.
5. Ref: Processor EDS documents
vol0.51 #815002
BUG=b:348678529
TEST=Verified on Intel® Simics® Pre Silicon Simulation platform for
PTL using google/fatcat mainboard.
Change-Id: Ibcfe71eec27cebf04f10ec343a73dd92f1272aca
Signed-off-by: Saurabh Mishra <mishra.saurabh@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/83354
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Update dptf settings for EVT.
BUG=None
TEST=emerge-brox coreboot chromeos-bootiamge
Change-Id: Iadc95c14da6f879e25dac4804907e340dc16e47f
Signed-off-by: Morris Hsu <morris-hsu@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/83842
Reviewed-by: Ren Kuo <ren.kuo@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Update touchpad settings.
BUG=b:342867386
TEST=ensure touchpad is working.
Change-Id: Ibf62470b7fd921065201894a63d7e2a83dad53ce
Signed-off-by: Morris Hsu <morris-hsu@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/83840
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Ren Kuo <ren.kuo@quanta.corp-partner.google.com>
|
|
Add TPM TIS ACPI interrupt configuration, set teliks's
`TPM_TIS_ACPI_INTERRUPT` to 13.
BUG=b:352263941
TEST=emerge-nissa coreboot
Change-Id: Iaed51e0bb8abac0ed0b35bfcf12e95fd34f92242
Signed-off-by: Qinghong Zeng <zengqinghong@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/83832
Reviewed-by: Eric Lai <ericllai@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Weimin Wu <wuweimin@huaqin.corp-partner.google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
Because one side is not displayed when using type-c projection, the
configuration of DP AUX BIAS to SOC direct connection is added.
BUG=b:352263941
TEST=DP function of MB and DB workable
Change-Id: Id89d02212cdad549d1c26ed51a8d5af0f4e757c6
Signed-off-by: Qinghong Zeng <zengqinghong@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/83829
Reviewed-by: Weimin Wu <wuweimin@huaqin.corp-partner.google.com>
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch add a new Kconfig HAVE_SPECIFIC_GPMR and use it to include
soc/gpmr.h if necessary.
Change-Id: I94797a72af75fc96ab2cacb1d46b581605a15387
Signed-off-by: Yuchi Chen <yuchi.chen@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/83317
Reviewed-by: Shuo Liu <shuo.liu@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
For easier debugging it is useful to have a function that prints the PMP
regions.
Signed-off-by: Maximilian Brune <maximilian.brune@9elements.com>
Change-Id: I6ab1531c65b14690e37aecf57ff441bf22db1ce5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/83283
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-by: ron minnich <rminnich@gmail.com>
|
|
Use 'enum cb_err' instead of {-1,0}.
Change-Id: Icea33ea3e6a5e3c7bbfedc29045026cd722ac23e
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/83503
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
|
|
We introduce two new functions to create region objects. They allow us
to check for integer overflows (region_create_untrusted()) or assert
their absence (region_create()).
This fixes potential overflows in region_overlap() checks in SMI
handlers, where we would wrongfully report MMIO as *not* overlapping
SMRAM.
Also, two cases of strtol() in parse_region() (cbfstool), where the
results were implicitly converted to `size_t`, are replaced with the
unsigned strtoul().
FIT payload support is left out, as it doesn't use the region API
(only the struct).
Change-Id: I4ae3e6274c981c9ab4fb1263c2a72fa68ef1c32b
Ticket: https://ticket.coreboot.org/issues/522
Found-by: Vadim Zaliva <lord@digamma.ai>
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79905
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
LAPIC has been available since P54C released 1993.
Change-Id: Id564a3007ea7a3d9fb81005a05399a18c4cf7289
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61794
Reviewed-by: coreboot org <coreboot.org@gmail.com>
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch enables pch_hda_sdi_enable for the trulo baseboard and
removes SDI lanes update from its variants.
BUG=b:350931954
TEST=Boot verified on google/craask and google/tivviks
Change-Id: I2e0f43b8fffb5e583089769d2c7446b476ce5d5d
Signed-off-by: Dinesh Gehlot <digehlot@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/83859
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
To publish the Bluetooth Regulator Domain Settings under the right
ACPI device scope, the wifi generic driver requires the bluetooth
companion to be set accordingly.
BUG=b:345373187
TEST=Build and test on google/rex0, check BRDS is shown in SSDT.
Change-Id: I28541e7a23dd486d3e0ec38ee89e1ab13595fc72
Change-Id: I82f6290cb1934e2c0597286702f93e3789e8f345
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/83844
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: YH Lin <yueherngl@google.com>
|
|
To publish the Bluetooth Regulator Domain Settings under the right
ACPI device scope, the wifi generic driver requires the bluetooth
companion to be set accordingly.
BUG=b:345373187
TEST=Build and test on karis, check BRDS is shown in SSDT.
Change-Id: I28541e7a23dd486d3e0ec38ee89e1ab13595fc72
Signed-off-by: Tyler Wang <tyler.wang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/83791
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Jérémy Compostella <jeremy.compostella@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: YH Lin <yueherngl@google.com>
|
|
This reverts commit 1f1d8d2bcae64baea19d0e947ba5572a45f46eec.
Reason for revert: Intel® Wi-Fi 6E AX211 (CNVi) does not need Bluetooth
Regulator Domain Settings and therefore, the bluetooth companion
device declaration for CNVi is unnecessary.
BUG=b:345373187
TEST=Able to build and boot google/karis.
Change-Id: I296ddb93659af144e1a82a6b8219c9811c5fe545
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/83843
Reviewed-by: YH Lin <yueherngl@google.com>
Reviewed-by: Jérémy Compostella <jeremy.compostella@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
<device/mmio.h> is supposed to chain-include <arch/mmio.h>. See
`Documentation/contributing/coding_style.md` section `Headers and includes`
Change-Id: I08f7480650b42df1613994146a026bd1e12dbf66
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82693
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
|
|
Change-Id: Iab7e9f3d17c87576761333c4b62c40eea5e424a5
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82250
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
|
|
Use of smbios_memory_type needs <smbios.h>.
Change-Id: Iacab6171c61abd047c09ff7e20313a455bd8414f
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82245
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
|
|
Refactor EINT driver by
- Move `pos_bit_calc_for_eint` to `common/gpio_eint_v1.c` and rename to
`gpio_calc_eint_pos_bit`.
- Implement `gpio_get_eint_reg` to obtain EINT base address.
This change is prepared for the driver change in MT8196.
BUG=b:334723688
TEST=EINT works on Geralt
Change-Id: Ie53abc23971bfa39250ebd7dd48e28d6b91c5973
Signed-off-by: Yidi Lin <yidilin@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/83703
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
1. print host software ownership, SMI enable and NMI enable registers
after configuring
2. read and print GPIO configuration dword registers after writing
3. use %zu to print size_t values according to CI reporting.
Change-Id: I8820956f6db91c7bcc26b46a4361da3dfa8f77b5
Signed-off-by: Yuchi Chen <yuchi.chen@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/83316
Reviewed-by: Shuo Liu <shuo.liu@intel.com>
Reviewed-by: Jérémy Compostella <jeremy.compostella@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Pass the PSP NVRAM base and size to amdfwtool for all SoCs except Genoa
and Stoneyridge which don't use/support this.
If a mainboard has an section named 'PSP_RPMC_NVRAM' in its FMAP file,
the start and length of it in the flash will be passed to amdfwtool
which then adds the base and length to the corresponding type 0x54 PSP
directory table entry.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Id9f8a7eec68a5222be63e46173132f1c4a461b4f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/83815
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
|
|
Devicetree for lenovo/520 is missing USB ports config, hence they
don't work. This change introduces USB port config.
Tests performed:
- Can select a boot media using a USB keyboard from any port.
- Can boot from each port except usb@1:1.1.
- Measured read speed from a thumb drive on each port 24.5-28.9 MiB/s.
Change-Id: I96dba153a563e0e290b96b837fdca39d7598ef17
Signed-off-by: PuFF1k <exopuf@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/83764
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
|
|
As `qemu-q35/memmap.c` includes `qemu-q35/q35.h`, move macros into q35.h
file.
Change-Id: I0bf13def8bc4510053f6bb44e043bbcb0b958b01
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/83407
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
|
|
Details:
- Skeleton files to compile google/fatcat mainboard.
BUG=b:348678529
TEST=Build verified on with using PTL SOC and google/fatcat mainboard.
Change-Id: I4c069ba64f487259ce746dc52296618d91209602
Signed-off-by: Saurabh Mishra <mishra.saurabh@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/83732
Reviewed-by: Ronak Kanabar <ronak.kanabar@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Ravishankar Sarawadi <ravishankar.sarawadi@intel.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Jamie Ryu <jamie.m.ryu@intel.com>
|
|
This patch adds new North Peak PCI device IDs for Intel PTL-U and PTL-H.
Additionally, updates the tracehub driver's `pci_device_ids` list to
include these new IDs.
Source: Intel PTL-EDS vol 1. Document Number 815002, Rev 0.51 Chapter 2
BUG=b:347669091
TEST=Boot to OS using PTL Silicon, verify if above 4GB IMR region is
reserved.
Signed-off-by: Bora Guvendik <bora.guvendik@intel.com>
Change-Id: Ifa1a0a57c504e06d686e7e0826547251b456cc8b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/83786
Reviewed-by: Anil Kumar K <anil.kumar.k@intel.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The Fn key on jubilant emits a scancode of 94 (0x5e).
BUG=b:324079605
TEST=Flash jubilant, boot to Linux kernel, and verify that KEY_FN is
generated when pressed using `evtest`.
Change-Id: I963b0aa85598097fea69ec34d1e79ec0bbec3db3
Signed-off-by: Morris Hsu <morris-hsu@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/83821
Reviewed-by: Ren Kuo <ren.kuo@quanta.corp-partner.google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Since a generic ITE GPIO driver is available and in use, the existence
of chips-specific drivers no longer make sense. Remove the dead code
in favor of generic GPIO driver.
Change-Id: I7e031d12192af4bd47923d87c1d02c64f9c851a2
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/83497
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Refactor mainboards' code to use the new GPIO driver.
TEST=Put Google Jecht to S3 sleep and check if the LED blinks.
Change-Id: I707ee090ee2551b4935847e12ade678d36ff9302
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Tested-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/83469
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Add SAR Sensor SX9324 for WWAN:
- Apply DRIVERS_I2C_SX9324
- Config GPP_H19 for IRQ
- Add SX9324 registers settings based on tuning value from SEMTECH.
Refer to datasheet:
https://chromeos.google.com/partner/dlm/avl/component/3624/
BUG=b:345327104
TEST=Build and verify on jubilant
Change-Id: I629117f20ca513dc0c8eaa91744ad33e162ba4bb
Signed-off-by: Ren Kuo <ren.kuo@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/83779
Reviewed-by: Kenneth Chan <kenneth.chan@quanta.corp-partner.google.com>
Reviewed-by: David Wu <david_wu@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
wifi.SetTXPower test fail, so enable wifi sar.
BUG=b:351698478
TEST=emerge-brox coreboot
Change-Id: Ibf5425e72eddc45e376ef4e2d077180dab502200
Signed-off-by: Kun Liu <liukun11@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/83793
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jian Tong <tongjian@huaqin.corp-partner.google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Update header files for FSP for Raptor Lake refresh platform to
version 5045_00, previous version being 4435_00.
FSPM:
1. Add IgdGsm2Size UPD
2. Comment added for Offset 0x0AB6
FSPS:
1. Add CepEnable UPD
2. Offset size updated for UPD ReservedCpuPostMemProduction
2. Comment added for Offset 0x104C
MemInfoHob:
1. Structure updated
BUG=b:355384183
Kit:https://www.intel.com/content/www/us/en/secure/design/confidential/
software-kits/kit-details.html?kitId=815173
Cq-Depend: chrome-internal:7554984
Change-Id: I80cccb6aaa8f3a97d860a1e7908bfac0435b1aec
Signed-off-by: Kulkarni, Srinivas <srinivas.kulkarni@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/83653
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
This change adds the necessary configuration for the G2 Touchscreen(GTCH7503) device, connected to I2C bus 40.
It includes settings for:
* HID descriptor
* Device description
* IRQ configuration
* Detection
* Reset and enable GPIOs with their respective delays
* Power resource handling
* HID descriptor register offset
BUG=b:350844195
TEST=emerge-nissa coreboot
boot with G2 TS, make sure G2 TS is functional.
Change-Id: If17367cd62eb69a1237efe4aa3ca1a0c9640ba4c
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/83823
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
MKBP device is required for passing events from input sources to AP.
Input sources include buttons (power, volume); switches (lid, tablet
mode) and sysrq.
BUG=b:357521411
TEST=Build coreboot and switch tablet mode on orisa.
Change-Id: Ic712f53fb4063347c38df05167f0100afc06f979
Signed-off-by: Amanda Huang <amanda_hwang@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/83819
Reviewed-by: Eric Lai <ericllai@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
This change adds support for specifying the CSE_RW_VERSION directly in
Kconfig.
* If `CONFIG_SOC_INTEL_CSE_RW_VERSION` is defined, its value will be
used directly as the CSE_RW version.
* Otherwise, the version will be extracted from the CSE_RW binary file
as before.
Platform prior to Intel Meteor Lake still requires to override the CSE
RW version using CONFIG_SOC_INTEL_CSE_RW_VERSION config rather reading
the CSE RW version from CSE RW partition.
BUG=b:327842062
TEST=CSE RW update successful on Karis with this patch using below
recipe:
1. Overriding the CONFIG_SOC_INTEL_CSE_RW_VERSION="18.0.5.2269"
2. Without overriding the CONFIG_SOC_INTEL_CSE_RW_VERSION=""
Platform prior to Intel Meteor Lake would be using #1 and platform
starting with Meteor Lake expected to use #2 recipe.
Change-Id: I1327c813b7aef77c65766eb9c40003bb8a71d4b6
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/83831
Reviewed-by: Eric Lai <ericllai@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Dinesh Gehlot <digehlot@google.com>
|
|
This change adds support for soldered-down memory on the Fatcat board.
It introduces a new Kconfig option `MEMORY_SOLDERDOWN` and includes
the necessary Makefiles adjustments to handle SPD data in CBFS when
this option is enabled.
* A new Kconfig option `MEMORY_SOLDERDOWN` is added to control
soldered-down memory support.
* When `MEMORY_SOLDERDOWN` is enabled, it selects:
* `CHROMEOS_DRAM_PART_NUMBER_IN_CBI` if `CHROMEOS` is enabled
* `HAVE_SPD_IN_CBFS`
* The Makefile is updated to include the `variants/$(VARIANT_DIR)/
memory` subdirectory and conditionally include the `spd` subdirectory
based on `CONFIG_HAVE_SPD_IN_CBFS`.
BUG=b:348678071
TEST=Able to build google/fatcat with N-1 silicon.
Change-Id: I7edc1134630940812186118a29cbbd550f0e3634
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/83828
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Ravishankar Sarawadi <ravishankar.sarawadi@intel.com>
Reviewed-by: Pranava Y N <pranavayn@google.com>
|
|
Add the support LP5 RAM parts for fatcat:
DRAM Part Name ID to assign
H58G56BK7BX068 0 (0000)
BUG=b:347669091
TEST=emerge-fatcat coreboot
Change-Id: Idcdbbcd42dc6b1c8b13a89b1ace5b2973dde6d2b
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/83824
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Pranava Y N <pranavayn@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Ravishankar Sarawadi <ravishankar.sarawadi@intel.com>
|
