| Age | Commit message (Collapse) | Author |
|---|
|
Enhance USB 2.0 SI by increasing the level of "HS DC Voltage Level"
and "Disconnect Threshold Adjustment".
COMPDISTUNE0: 0x3->0x7
TXVREFTUNE0: 0x6->0xf
BUG=b:162614573
BRANCH=zork
TEST=1. emerge-zork coreboot
2. check U2 registers are set correctly
3. test with servo v4 type-c, it's working expectedly.
4. U2 SI pass
Signed-off-by: Kevin Chiu <kevin.chiu@quantatw.com>
Change-Id: I278cc0aaddbc9fce595bf57ca69ee8abfc9f5659
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46537
Reviewed-by: Rob Barnes <robbarnes@google.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Correct the two load line slope settings for the SVID3 telemetry.
AGESA sends these values to the SMU, which accepts them as units
of current. Proper calibration is determined by the AMD SDLE tool
and the Stardust test.
BUG=b:168265881
BRANCH=zork
TEST=emerge-zork coreboot
Change-Id: Id6c4f1a92d7f2ad293df7b63694e9665b85f8018
Signed-off-by: Kevin Chiu <kevin.chiu@quantatw.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46472
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Chris Wang <chris.wang@amd.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Early JSL silicon hang while booting Linux with ISST enabled. The
malfunctioning silicon revisions have been used only for development
purposes and have been phased out. Thus, drop the ISST workaround.
Change-Id: Ic335c0bf03a5b07130f79c24107a1b1b0ae75611
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46459
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Deduplicate code by using the new common cpu code implementation of
AES-NI locking.
Change-Id: I7ab2d3839ecb758335ef8cc6a0c0c7103db0fa50
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46278
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Currently, the serial console does not work.
With the serial port enabled in the vendor firmware, `superiotool` outputs
the global control register values below.
Found Nuvoton NCT6779D (id=0xc562) at 0x2e
Register dump:
idx 10 11 13 14 1a 1b 1c 1d 20 21 22 24 25 26 27 28 2a 2b 2c 2f
val ff ff ff ff 3a 28 00 10 c5 62 df 04 00 00 10 00 48 20 00 01
def ff ff 00 00 30 70 10 00 c5 62 ff 04 00 MM 00 00 c0 00 01 MM
UART A needs to be enabled in CR 0x2a by clearing bit 7. Do this by
selecting the Super I/O Kconfig symbol `SUPERIO_NUVOTON_COMMON_COM_A`.
This changes the default value 0xc0 to 0x40.
Note, due configuring the system as legacy free with
`HUDSON_LEGACY_FREE=y`, AGESA in romstage disables the LPC controller in
`FchInitResetLpcProgram()`.
coreboot-4.12-3417-g192b9576fe Tue Oct 20 09:15:53 UTC 2020 romstage starting (log level: 7)...
APIC 00: CPU Family_Model = 00610f31
APIC 00: ** Enter AmdInitReset [00020007]
Fch OEM config in INIT RESET
`AmdInitReset() returned AGESA_SUCCESS` is not transmitted anymore. Only
when coreboot enables the LPC controller again in ramstage, serial output
continues.
PCI: 00:14.4 bridge ctrl <- 0013
PCI: 00:14.4 cmd <- 00
PCI: 00:14.5 cmd <- 02
PCI: 00:15.0 bridge ctrl <- 0013
PCI: 00:15.0 cmd <- 00
PCI: 00:15.1 bridge ctrl <- 0013
[…]
done.
BS: BS_DEV_ENABLE run times (exec / console): 0 / 30 ms
Initializing devices...
CPU_CLUSTER: 0 init
[…]
Note, due to incorrect Super I/O configuration in the devicetree, the boot
hangs in `PCI: 00:14.3 init` when doing `outb(0, DMA1_RESET_REG)`. This
will be fixed in follow-up commits.
TEST=Receive (some) coreboot log messages over the serial console.
Change-Id: I0aa367316f274ed0dd5964ba5ed045b9aeaccf8d
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39371
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Following commit f50ea988b a couple of symbols are gone, so follow up
that change for this board as well.
Change-Id: I09fd3a107447eb45bb46b7f0f821377943f140b2
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46621
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Get rid of legacy pad macros by replacing them with their newer
equivalents.
TEST: TIMELESS-built board images match
Change-Id: I078f9bb3c78f642afc6dcfd64d77be823a4485c2
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46567
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This converts the constant for the XTAL frequency to a Kconfig option.
Change-Id: I1382dd274eeb9cb748f94c34f5d9a83880624c18
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46018
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Add a Kconfig for SoCs to indicate PM ACPI timer emulation support and
select it by the appropriate SoCs.
This Kconfig gets used in the follow-up changes.
Change-Id: I6ded79221a01655f298ff92b8bd2afabd1d2a3ff
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46017
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Update PL1 max and min power values
BUG=None
BRANCH=None
TEST=build and verify on dralat system
Change-Id: I75d47fa721576564f71fbd5d5fd2e820fc3f1925
Signed-off-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46502
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
When MRC_SAVE_HASH_IN_TPM is selected, we can just use the TPM hash to
verify the MRC_CACHE data. Thus, we don't need to calculate the
checksum anymore in this case.
BUG=b:150502246
BRANCH=None
TEST=make sure memory training still works on nami
Change-Id: I1db4469da49755805b541f50c7ef2f9cdb749425
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46515
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Pull selection of tpm hash index logic into cache_region struct. This
CL also enables the storing of the MRC hash into the TPM NVRAM space
for both recovery and non-recovery cases. This will affect all
platforms with TPM2 enabled and use the MRC_CACHE driver.
BUG=b:150502246
BRANCH=None
TEST=make sure memory training still works on nami and lazor
Change-Id: I1a744d6f40f062ca3aab6157b3747e6c1f6977f9
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46514
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Add new index for MRC_CACHE data in RW. Also update antirollback
functions to handle this new index where necessary.
BUG=b:150502246
BRANCH=None
TEST=make sure memory training still works on nami
Change-Id: I2de3c23aa56d3b576ca54dbd85c75e5b80199560
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46511
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
We need to extend the functionality of the mrc_cache hash functions to
work for both recovery and normal mrc_cache data. Updating the API of
these functions to pass in an index to identify the hash indices for
recovery and normal mode.
BUG=b:150502246
BRANCH=None
TEST=make sure memory training still works on nami
Change-Id: I9c0bb25eafc731ca9c7a95113ab940f55997fc0f
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46432
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This CL would remove these calls from fsp 2.0. Platforms that select
MRC_STASH_TO_CBMEM, updating the TPM NVRAM space is moved from
romstage (when data stashed to CBMEM) to ramstage (when data is
written back to SPI flash.
BUG=b:150502246
BRANCH=None
TEST=make sure memory training still works on nami
Change-Id: I3088ca6927c7dbc65386c13e868afa0462086937
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46510
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
Use this config to specify whether we want to save a hash of the
MRC_CACHE in the TPM NVRAM space. Replace all uses of
FSP2_0_USES_TPM_MRC_HASH with MRC_SAVE_HASH_IN_TPM and remove the
FSP2_0_USES_TPM_MRC_HASH config. Note that TPM1 platforms will not
select MRC_SAVE_HASH_IN_TPM as none of them use FSP2.0 and have
recovery MRC_CACHE.
BUG=b:150502246
BRANCH=None
TEST=emerge-nami coreboot chromeos-bootimage
Change-Id: Ic5ffcdba27cb1f09c39c3835029c8d9cc3453af1
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46509
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
When emitting ACPI tables for the Type-C connector class, skip writing
out a device reference if it is to a disabled device.
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: I84cc3e1a54e2b654239ad6e1a4662d582f3465cf
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45877
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
On DeltaLake server, there are following entry in MTRR address space:
0x0000201000000000 - 0x0000201000400000 size 0x00400000 type 0
In this case, the base address (with 4k granularity) cannot be held in
uint32_t. This results incorrect MTRR register setup. As the consequence
UEFI forum FWTS reports following critical error:
Memory range 0x100000000 to 0x183fffffff (System RAM) has incorrect attribute Uncached.
Change appropriate variables' data type from uint32_t to uint64_t.
Add fls64() to find least significant bit set in a 64-bit word.
Add fms64() to find most significant bit set in a 64-bit word.
Signed-off-by: Jonathan Zhang <jonzhang@fb.com>
Signed-off-by: Marc Jones <marcjones@sysproconsulting.com>
Change-Id: I41bc5befcc1374c838c91b9f7c5279ea76dd67c7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46435
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Configure board specific DPTF parameters for terrador and todor
BUG=b:171019363,b:170699797
BRANCH=volteer
TEST=build and verify by thermal team
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Change-Id: I19935ca98ec7a078869e73d65ea471df70f37121
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46487
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Add generic LPDDR4x SPD support for the following three memory
parts:
• K4U6E3S4AA-MGCR
• H9HCNNNBKMMLXR-NEE
• MT53E512M32D2NP-046 WT:F
BUG=b:170264065
TEST=none
Change-Id: Ie3163763a0ce291f27c43181d35c070c218b461d
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46349
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
MSR_FEATURE_CONFIG, which is used for locking AES-NI, is core-scoped,
not package-scoped. Thus, move locking from SMM to core init, where the
code gets executed once per core.
Change-Id: I3a6f7fc95ce226ce4246b65070726087eb9d689c
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46535
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
The Picasso build describes the DRAM region where the PSP places
our bootblock. Rather than relying on Kconfig values, make the build
more robust by using the actual size and target base address
from the boot block's ELF file.
Sample output of "readelf -l bootblock.elf" is:
------------------
Elf file type is EXEC (Executable file)
Entry point 0x203fff0
There is 1 program header, starting at offset 52
Program Headers:
Type Offset VirtAddr PhysAddr FileSiz MemSiz Flg Align
LOAD 0x001000 0x02030000 0x02030000 0x10000 0x10000 RWE 0x1000
Section to Segment mapping:
Segment Sections...
00 .text .data .bss .reset
------------------
We can extract the information from here.
BUG=b:154957411
TEST=Build & boot on mandolin
Change-Id: I5a26047726f897c57325387cb304fddbc73f6504
Signed-off-by: Zheng Bao <fishbaozi@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46092
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Tested with BUILD_TIMELESS=1, Packard Bell MS2290 remains identical.
Change-Id: I30512ef7ff7eb091e1f880c43a0a9ecf8625a710
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46530
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add devicetree and device ID for P-sensor
BUG=b:161217096
BRANCH=NONE
TEST=We can get the data from P-sensor if touch the SAR antenna.
Signed-off-by: alec.wang <alec.wang@lcfc.corp-partner.google.com>
Change-Id: I70f303995b106cca9758b36ebcde112ebcc90950
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46333
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marco Chen <marcochen@google.com>
Reviewed-by: Jamie Chen <jamie.chen@intel.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Update devicetree of boten that enable stylus
BUG=b:160752604
BRANCH=NONE
TEST=build bios and verify function for boten
Signed-off-by: alec.wang <alec.wang@lcfc.corp-partner.google.com>
Change-Id: Ifbcac18fcf758f3d870a6af0d1b03e34369414c0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45807
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marco Chen <marcochen@google.com>
Reviewed-by: Jamie Chen <jamie.chen@intel.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
I often find myself having to increase the CBFS size so that TianoCore
fits. Raise the default CBFS size to 2 MiB to alleviate this issue.
Change-Id: I871bb95dee55cc5bad68bb6e71f89ddfa4823497
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46488
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This adds another X11 series board, the X11SSH-F, which is similiar to
X11SSH-TF but differs in PCIe interfaces/devices, ethernet interfaces.
Signed-off-by: Bill XIE <persmule@hardenedlinux.org>
Change-Id: I92c32bff861f0b5697aea52ff282fae76b3b78ac
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45229
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
|
|
Signed-off-by: Huayang Duan <huayang.duan@mediatek.com>
Signed-off-by: Yidi Lin <yidi.lin@mediatek.com>
Change-Id: Ied350570a695cca1424a6562e41120bcaf467797
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44568
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Load params from flash and use those params to do dram fast calibration.
Signed-off-by: Huayang Duan <huayang.duan@mediatek.com>
Signed-off-by: Yidi Lin <yidi.lin@mediatek.com>
Change-Id: I45a4fedc623aecfd000c5860e0e85175f45b8ded
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44569
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
Add APIs to get and set the voltage for the target regulator.
BUG=b:147789962
BRANCH=none
TEST=emerge-asurada coreboot
Change-Id: I0e56df45fc3309c387b9949534334eadefb616b2
Signed-off-by: Yidi Lin <yidi.lin@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46404
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
Lock AES-NI (MSR_FEATURE_CONFIG) to prevent unintended changes of
AES-NI enablement as precaution, as suggested in Intel document
325384-070US.
Locking is enabled by default (as already done in SKL and Arrandale) and
may be disabled by the newly introduced Kconfig in the parent change.
Tested by checking the MSR.
Change-Id: I79495bfbd3ebf3b712ce9ecf2040cecfd954178d
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46273
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Add a Kconfig to be able to disable locking of AES-NI for e.g debugging,
testing, ...
Change-Id: I4eaf8d7d187188ee6e78741b1ceb837c40c2c402
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46277
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Add a check to only lock AES-NI when AES is supported.
Change-Id: Ia7ffd5393a3e972f461ff7991b9c5bd363712361
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46276
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Simplify the AES-NI code by using msr_set and correct the comment.
Change-Id: Ib2cda433bbec0192277839c02a1862b8f41340cb
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46275
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Copy the AES-NI locking function to common cpu code to be able to reuse
it.
This change only copies the code and adds the MSR header file. Any
further rework and later deduplication on the platforms code is done in
the follow-up changes.
Change-Id: I81ad5c0d4797b139435c57d3af0a95db94a5c15e
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46272
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
The PSP does not accept the SmmInfo command during a resume so
remove the call.
BUG=b:163017485
TEST=Run SST on trembyle, verify error message goes away
BRANCH=Zork
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Change-Id: Ib75a20c9594bc331aa7abf77be95196085a3dbc6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44398
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Correct the base address. This should have no noticeable effect,
as SMC_MSG_S3ENTRY accepts no arguments and doesn't return. The
argument writes were not getting to any target.
BUG=b:171037051
TEST=Run SST on morphius
BRANCH=Zork
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Change-Id: Ie3402f743cf7d4f4f42b8afa3e8b253be4761949
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46505
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
This Chili mainboard is used in an all-in-one PC.
For more information see
https://www.secunet.com/fileadmin/user_upload/_temp_/importexport/Print/Factsheets/englisch/SINA_Workstation_H_Client_V_Factsheet_EN_Web.pdf
Change-Id: Ic7a5dccbb0d5b7bceb154fb050cf991254475f7b
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Signed-off-by: Felix Singer <felix.singer@secunet.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39995
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Thomas Heijligen <src@posteo.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I3e4824722d3add989a352122b365c2a73f3f703b
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46329
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
Change-Id: Idd16454884d6d847eb7ad071ff1d3e0c0de53e5b
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46330
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
Change-Id: I8d54e157e4f0065fa0fd3df9df81a5b336031a99
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46332
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
The Chili base board is a ruggedized laptop with additional industrial
interfaces. So far, only booting and basic interfaces (USB, UART,
Video) are working with the original model, the "base" variant.
No further development is planned for this variant, as our primary
target was another one that will be added in a follow-up.
Change-Id: I1d3508b615ec877edc8db756e9ad38132b37219c
Signed-off-by: Thomas Heijligen <thomas.heijligen@secunet.com>
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Signed-off-by: Felix Singer <felix.singer@secunet.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39976
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
BUG=b:170703029
BRANCH=octopus
TEST=emerge-octopus coreboot
Signed-off-by: James Chao <james_chao@asus.corp-partner.google.com>
Change-Id: I2bf642963283b8a31a3bd9504c40541ca2f64b34
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46344
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
|
|
The XTAL shutdown (dis)qualification bit already unconditionally gets
set to 1 by FSP for these platforms, making this code redundant.
Change-Id: I7fa4afb0de2af1814e5b91c152d82d7ead310338
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46016
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
disabled"
This reverts commit e5269a8fd975fa0cba0655cd41f7f8cc99a1feb8.
Reason for revert: BIOS spec says, it's recommended to always enable
emulation (regardless of the OS version).
Change-Id: If0d7fa6f9766c7c4e2fa9e846c179adc6a4e1681
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45000
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Tested with BUILD_TIMELESS=1, Packard Bell MS2290 remains identical.
Change-Id: I01730e25ee78a74048f0b93faef00ebaee82ba77
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46529
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
There's no need to have multiple Kconfig symbols which do the same
thing. Introduce `SUPERIO_NUVOTON_COMMON_COM_A` and update boards to use
the new symbol. To preserve alphabetical order in mainboard Kconfig,
place the new symbol above the Super I/O symbol (instead of below).
Change-Id: Ic0a30b3177a1a535261525638be301ae07c59c14
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46522
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Bit 6 of global CR 0x2a toggles the mux for COM B. Bit 7 works just like
on the other two Nuvoton Super I/Os, so fold the conditionals together.
Change-Id: I8cebe35587ae68cac93ed392342662678621efd6
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46521
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
|
|
No recent Chromebooks have used I2C for TPM communication, and as a
result, a bug has crept in. The ability to extract Cr50 firmware string
is only supported via SPI, yet code in mainboard and vendorcode attempt
to do so unconditionally.
This CL makes it such that the code also compiles for future designs
using I2C. (Whether we want to enhance the I2C protocol to be able to
provide the version string, and then implement the support is a separate
question.)
This effort is prompted by the desire to use reworked Volteer EVT
devices for validating the new Ti50/Dauntless TPM. Dauntless will
primarily be using I2C in upcoming designs.
BRANCH=volteer
TEST=util/abuild/abuild -t GOOGLE_VOLTEER -c max -x
Change-Id: Ida1d732e486b19bdff6d95062a3ac1a7c4b58b45
Signed-off-by: jbk@chromium.org
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46436
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Caveh Jalali <caveh@chromium.org>
|
|
As ongoing work for generalizing mrc_cache to be used by all
platforms, we are pulling it out from fsp 2.0 and renaming it as
mrc_cache_hash_tpm.h in security/vboot.
BUG=b:150502246
BRANCH=None
TEST=emerge-nami coreboot chromeos-bootimage
Change-Id: I5a204bc3342a3462f177c3ed6b8443e31816091c
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46508
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
The subsystem ID registers are read/write-once. Writes by coreboot will
not take effect if FSP sets them.
Note that FSP sets one device ID for the SA devices and another for PCH
devices. coreboot will copy individual vendor and device IDs if
subsystem is not provided.
Change-Id: I9157fb69f2a49dfc08f049da4b39fbf86614ace3
Signed-off-by: Benjamin Doron <benjamin.doron00@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45006
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Coverity detects source memory is overrun. Fix this issue by using
the CONFIG_MAX_ROOT_PORTS value to avoid memory corruption.
Found-by: Coverity CID 1429762 1429774
TEST=None
Signed-off-by: John Zhao <john.zhao@intel.com>
Change-Id: Icc253eb9348d959a9e9e69a3f13933b7f97d6ecc
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46504
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Test: built google/volteer with `abuild --timeless` - SHA1 hashes match
Change-Id: Ice6cef402dfcc33f1fc7fdced66d38c380d338e5
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46467
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
This reverts commit c4a5acdabc28778b49a1c088b0736bac83e2ab51.
Reason for revert: Dalboz is missing pull-up on cmd line, so 400khz is not possible.
TEST=Boot Dalboz
BUG=b:159823235, b:169940175
BRANCH=zork
Change-Id: I89653bfeefa522c17ee2d736215bc22aa445871c
Signed-off-by: Rob Barnes <robbarnes@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45004
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
The camera sensor component chosen for UFC and WFC have an address
conflict. Resolve it by enabling GPIO based I2C Multiplexer. Also
configure the GPIO that is used as select line.
BUG=b:169444894
TEST=Build and boot waddledee to OS. Ensure that the ACPI identifiers
are added for I2C devices multiplexed using I2C MUX under the
appropriate scope.
Change-Id: I9b09e063b4377587019ade9e6e194f4aadcdd312
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45912
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This chip driver adds ACPI identifiers for multiplexed I2C bus that are
selected using GPIO. The multiplexed bus device defines the address
to select the I2C lines. These ACPI identifiers are consumed by the
i2c-mux-gpio kernel driver:
https://www.kernel.org/doc/html/latest/i2c/muxes/i2c-mux-gpio.html
BUG=b:169444894
TEST=Build and boot to OS in waddledee. Ensure that the ACPI identifiers
are added in appropriate context.
Scope (\_SB.PCI0.I2C3.MUX0)
{
Device (MXA0)
{
Method (_STA, 0, NotSerialized) // _STA: Status
{
Return (0x0F)
}
Name (_ADR, Zero) // _ADR: Address
}
}
Scope (\_SB.PCI0.I2C3.MUX0)
{
Device (MXA1)
{
Method (_STA, 0, NotSerialized) // _STA: Status
{
Return (0x0F)
}
Name (_ADR, One) // _ADR: Address
}
}
Change-Id: If8b983bc8ce212ce05fe6b7f01a6d9092468e582
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46144
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Add identifiers in ACPI tables for GPIO based I2C multiplexer. The
multiplexer device defines the GPIO resource used to select the
adapter/bus lines. The multiplexer adapter device defines the address
to select the adapter/client lines. These ACPI identifiers are consumed
by the i2c-mux-gpio kernel driver:
https://www.kernel.org/doc/html/latest/i2c/muxes/i2c-mux-gpio.html
BUG=b:169444894
TEST=Build and boot waddledee to OS. Ensure that the ACPI identifiers
are added for I2C devices multiplexed using I2C MUX under the
appropriate scope. Here is the output SSDT:
Scope (\_SB.PCI0.I2C3)
{
Device (MUX0)
{
Name (_HID, "PRP0001") // _HID: Hardware ID
Method (_STA, 0, NotSerialized) // _STA: Status
{
Return (0x0F)
}
Name (_CRS, ResourceTemplate () // _CRS: Current Resource Settings
{
GpioIo (Exclusive, PullDefault, 0x0000, 0x0000, IoRestrictionOutputOnly,
"\\_SB.PCI0.GPIO", 0x00, ResourceConsumer, ,
)
{ // Pin list
0x0125
}
})
Name (_DSD, Package (0x02) // _DSD: Device-Specific Data
{
ToUUID ("daffd814-6eba-4d8c-8a91-bc9bbf4aa301") /* Device Properties for _DSD */,
Package (0x02)
{
Package (0x02)
{
"compatible",
"i2c-mux-gpio"
},
Package (0x02)
{
"mux-gpios",
Package (0x04)
{
\_SB.PCI0.I2C3.MUX0,
Zero,
Zero,
Zero
}
}
}
})
}
}
Change-Id: Ib371108cc6043c133681066bf7bf4b2e00771e8b
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45911
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Change-Id: I3d5f595ebbc865501b086aebee1f492b4ab15ecd
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45700
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Make IMD private structures definitions accessible by other units.
To test IMD API correctness there is a need to access its internal
structure. It is only possible when private implementation is visible
in testing scope.
Signed-off-by: Jakub Czapiga <jacz@semihalf.com>
Change-Id: Iff87cc1990426bee6ac3cc1dfa6f85a787334976
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46216
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
|
|
The headers added are generated as per FSP v2376.
Previous FSP version was 2295.
Changes Include:
- add GpioOverride UPD in Fspm.h
- add new header FirmwareVersionInfo.h
Cq-Depend: TBD
Change-Id: I65c03d8eda11664541479983c7be11854410e1c6
Signed-off-by: Ronak Kanabar <ronak.kanabar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45899
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Replace vb2ex_hwcrypto_rsa_verify_digest with vb2ex_hwcrypto_modexp.
Instead of using hardware acceleration for whole RSA process,
acclerating only calculation part(modexp) increases transparency
without affecting boot time.
BUG=b:169157796
BRANCH=zork
TEST=build and flash, check time spent on RSA is not changed
Change-Id: I085f043bf2014615d2c9db6df0b7947ee84b9546
Signed-off-by: Kangheui Won <khwon@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45987
Reviewed-by: Edward O'Callaghan <quasisec@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Enable the USB4 retimer driver with GPP_H10 as the power control.
Change-Id: I166bc477f94c159bb411620a6bf77b5d1f194fb2
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44919
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
|
|
The USB4 retimer device needs to declare a _DSM with specific functions
that allow for GPIO control to turn off the power when an external
device is not connected. This driver allows the mainboard to provide
the GPIO that is connected to the power control.
BUG=b:156957424
Change-Id: Icfb85dc3c0885d828aba3855a66109043250ab86
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44918
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
To support camera second source GC5035 for kodama, add world facing
camera id as part of the sku id, which is determined by the data in
camera EEPROM. For models other than kodama, the camera id is always 0
and hence the sku id is unchanged.
BUG=b:144820097
TEST=emerge-kukui coreboot
TEST=Correct WFC id detected for kodama with GC5035 camera
BRANCH=kukui
Change-Id: I63a2b952b8c35c0ead8200d7c926e8d90a9f3fb8
Signed-off-by: Yu-Ping Wu <yupingso@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45811
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add cros_camera_info struct for camera information, and
check_cros_camera_info() for checking the magic, CRC and version.
BUG=b:144820097
TEST=emerge-kukui coreboot
BRANCH=kukui
Change-Id: I1215fec76643b0cf7e09433e1190e8bd387e6953
Signed-off-by: Yu-Ping Wu <yupingso@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46042
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add new memory.c to support DDR4 memory types.
BUG=b:170604353
TEST=emerge-volteer coreboot chromeos-bootimage
Change-Id: If96b0bda0ce95766f0957c37aa7cbecefc9c03e0
Signed-off-by: Wisley Chen <wisley.chen@quantatw.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46378
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
|
|
There's no need to use static functions to fill these settings in. Also,
add missing include for <stdint.h> and initialize `mem_cfg` in one line.
Change-Id: I82b0997846d4ec40cf9b1a8ebfb1e881b194e078
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46252
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Update dptc setting:
Stapm_time_constant 1400
BUG=b:170696020
BRANCH=zork
TEST=emerge coreboot and check "Stapm_time_constant"
Signed-off-by: John Su <john_su@compal.corp-partner.google.com>
Change-Id: I61d9e00a9d098ad9699b8cf89e70d11de2b95ffd
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46048
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Chris Wang <chris.wang@amd.corp-partner.google.com>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
|
|
Use the 96 character limit.
Signed-off-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Change-Id: I43d77db1f81d72aa13f3a702abff490a68a52bd7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46072
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
|
|
platform_fsp_silicon_init_params_cb is called by the fsp driver and
calls mainboard_silicon_init_params which sets the mainboard
PCH GPIOs.
Change-Id: Icf401e76741a6a7484295e999ddd566fe9510898
Signed-off-by: Marc Jones <marcjones@sysproconsulting.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46309
Reviewed-by: Jonathan Zhang <jonzhang@fb.com>
Reviewed-by: Bryant Ou <bryant.ou.q@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Drop the Kconfig for hyperthreading to be always able to check at
runtime if hyperthreading is supported. Having a Kconfig for this
doesn't have any benefit.
Change-Id: Ib7b7a437d758f7fe4a09738db1eab8189290b288
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46507
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
A newline is missing at the end of the informational message.
PNP: 002e.5 init
nct5572d_init: Disable mouse controller.PNP: 002e.5 init finished in 0 msecs
PNP: 002e.307 init
Change-Id: Ic73ed97be0993637be1e97040784d5a8e70a22ae
Fixes: 6ff1078990 ("superio: Log if mouse controller is disabled")
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45805
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
The passive clause is constructed with the past participle, which is
*defined* in this case. Fix all occurrences in AMD vendor code with the
command below.
git grep -l "is define at" src/mainboard/ | xargs sed -i 's/is define at/is defined at/'
Change-Id: I5aa0e6e064410b305aa5f2775271f6a8988da64b
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46066
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The passive clause is constructed with the past participle, which is
*defined* in this case. Fix all occurrences in AMD vendor code with the
command below.
$ git grep -l "is define at" src/vendorcode/amd/ | xargs sed -i 's/is define at/is defined at/'
Change-Id: Ia26c87aecb484dcb55737e417367757d38ce3b56
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46065
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
With a tabulator length of eight spaces, the alignment is the same, but
the other macro definitions are using a space, so do the same for
consistency, better alignment in diff views.
git grep -l -P 'define\tBLD' | xargs sed -i 's,define\tBLD,define BLD,g'
Change-Id: Ib71057c84dc897028cb0ceac29952e67bc541d2e
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46518
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Fixes: b266c6b5 ("AMD Steppe Eagle: Add binary PI vendorcode files")
Change-Id: Id317b53cfafaae629c2a94144c419e2112eaf7a9
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46517
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Currently, when selecting SUPERIO_NUVOTON_NCT*_COM_A, the whole global
control register 0x2a is written to 0x40. CR 0x2a defaults to 0xc0, so
indeed bit 7 is cleared, but the device early init code might have set
other bits in that control register, so setting it to 0x40 might
override already set bits. So, only clear bit 7 and leave the other bits
untouched.
Fixes: f95daa510d ("superio/nuvoton: Add back Nuvoton NCT6776 support")
Change-Id: I9ded9dab3985c4c8e5c45af354ef44af482e18c2
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46286
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Due to platform-specific constraints, it is not possible to enable DPR
by programming the MCH's DPR register in ramstage. Instead, assume it
has been programmed earlier and check that its value is valid. If it is,
then simply configure DPR in TXT public base with the same parameters.
Note that some bits only exist on MCH DPR, and thus need to be cleared.
Implement this function on most client platforms. For Skylake and newer,
place it in common System Agent code. Also implement it for Haswell, for
which the rest of Intel TXT support will be added in subsequent commits.
Do not error out if DPR is larger than expected. On some platforms, such
as Haswell, MRC decides the size of DPR, and cannot be changed easily.
Reimplementing MRC is easier than working around its limitations anyway.
Change-Id: I391383fb03bd6636063964ff249c75028e0644cf
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46490
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The BIOS ACM will check that enabled variable MTRRs do not cover more
than the ACM's size, rounded up to 4 KiB. If that is not the case,
launching the ACM will result in a lovely TXT reset. How boring.
The new algorithm simply performs a reverse bit scan in a loop, and
allocates one MTRR for each set bit in the rounded-up size to cache.
Before allocating anything, it checks if there are enough variable
MTRRs; if not, it will refuse to cache anything. This will result in
another TXT reset, initiated by the processor, with error type 5:
Load memory type error in Authenticated Code Execution Area.
This can only happen if the ACM has specific caching requirements that
the current code does not know about, or something has been compromised.
Therefore, causing a TXT reset should be a reasonable enough approach.
Also, disable all MTRRs before clearing the variable MTRRs and only
enable them again once they have been set up with the new values.
Tested on Asrock B85M Pro4 with a BIOS ACM whose size is 101504 bytes.
Without this patch, launching the ACM would result in a TXT reset. This
no longer happens when this patch is applied.
Change-Id: I8d411f6450928357544be20250262c2005d1e75d
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44880
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Christian Walter <christian.walter@9elements.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
When caching the BIOS ACM, one must cache less than a page (4 KiB) of
unused memory past the end of the BIOS ACM. Failure to do so on Haswell
will result in a lovely TXT reset with Class Code 5, Major Error Code 2.
The current approach uses a single variable MTRR to cache the whole BIOS
ACM. Before fighting with the variable MTRRs in assembly code, ensure
that enough variable MTRRs exist to cache the BIOS ACM's size. Since the
code checks that the ACM base is aligned to its size, each `one` bit in
the ACM size will require one variable MTRR to properly cache the ACM.
One of the several BIOS ACMs for Haswell has a size of 101504 bytes.
This is 0x18c80 in hexadecimal, and 0001 1000 1100 1000 0000 in binary.
After aligning up the BIOS ACM size to a page boundary, the resulting
size is 0x19000 in hexadecimal, and 0001 1001 0000 0000 0000 in binary.
To successfully invoke said ACM, its base must be a multiple of 0x20000
and three variable MTRRs must be used to cache the ACM. The MTRR ranges
must be contiguous and cover 0x10000, 0x8000, 0x1000 bytes, in order.
The assembly code is updated in a follow-up, and relies on these checks.
Change-Id: I480dc3e4a9e4a59fbb73d571fd62b0257abc65b3
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46422
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch adds some Kconfig hints to make it clearer that the
USE_QC_BLOBS option is required for SC7180 boards and guide the user in
the right direction through menuconfig. Also add those little arrows to
the Trogdor board options that are there on most other boards.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: I973cae8026a229408a1a1817c4808b0266387ea7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45214
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philip Chen <philipchen@google.com>
|
|
msr_set_bit can only set single bits in MSRs and causes mixing of bit
positions and bitmasks in the MSR header files. Thus, replace the helper
by versions which can unset and set whole MSR bitmasks, just like the
"and-or"-helper, but in the way commit 64a6b6c was done (inversion done
in the helper). This helps keeping the MSR macros unified in bitmask
style.
In sum, the three helpers msr_set, msr_unset and msr_unset_and_set get
added.
The few uses of msr_set_bit have been replaced by the new version, while
the used macros have been converted accordingly.
Change-Id: Idfe9b66e7cfe78ec295a44a2a193f530349f7689
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46354
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This configuration option shares a name with the FSP UPD, but
is enumerated differently. Change its name to minimise confusion
about the options.
Change-Id: Id74f043ecd549bde4501320bff1dc080bde64057
Signed-off-by: Benjamin Doron <benjamin.doron00@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45001
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Fix DSM function 0 (query function) to correctly report function support
for its revision. Revision 1 should return 0x3 because I2C HID supports
only 1 additional function. All other revisions should return 0.
BUG=b:170862147
BRANCH=Zork
TEST=ensure no dmesg errors; disassemble and verify SSDT
Signed-off-by: Josie Nordrum <JosieNordrum@google.com>
Change-Id: Iee082ef5cf44c4cf7ab304345af56f3b5173ca56
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46429
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Berknip has SSD/eMMC SKU, we should turn off eMMC if storage is NVMe SSD.
BUG=b:170592992
BRANCH=zork
TEST=1. emerge-zork coreboot
2. Check eMMC is enabled or disabled based on the eMMC bit in
FW_CONFIG.
Change-Id: I7aeabc98fc16bc2837c8dcdc40c3c6a80898cdc9
Signed-off-by: Kevin Chiu <kevin.chiu@quantatw.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46292
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Rob Barnes <robbarnes@google.com>
|
|
TEST=Build and test booting ADL RVP form NVMe and Optane
localhost ~ # lspci -d :f1a6
Show all the NVMe devices and be really verbose
localhost ~ # lspci -vvvd :f1a6
Print PCIe lane capabilities and configurations for all the NVMe devices.
Change-Id: I0a04b23b17df574d4fa3bae233ca40cd3b104201
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46420
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
A regular M.2 NVMe SSD shows up on RP9 and runs at x4 width.
Optane memory module shows up as 2 NVMe devices in x2 config:
- NVMe storage device uses RP9
- NVMe Optane memory uses RP11
Note: These two devices are sharing CLK PINs because of same M.2 slot.
TEST=Build and boot ADL RVP board using Intel Optane card.
Change-Id: Ia21d7d2fd07c4fb32291af7bb5a2e41e40316278
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46419
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Make PCI ClkReq-to-ClkSrc mapping correct to fix SSD detection issue
on ADL RVP.
TEST=Able to detect WD SSD card over PCH SSD RP9.
Change-Id: I7e26429281f8d3b9edae0f266a5868118369be3f
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46418
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
This patch programs GPIO for PCH SSD Power Enable (GPP_D16) and Port
Detect (GPP_A12) as per schematics.
TEST=Able to build and boot ADL RVP.
Change-Id: I015e46bdf25437c6b196deb3e610bc1b58726070
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46417
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Add 32-bit `popcnt` and 64-bit `popcnt64` helpers.
Change-Id: I2e6a1007e475b662a85c067d96f81326e7f02905
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46421
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Prepare for common ACPI. Add get_system_memory_map() helper
function to soc_util.c and use it in the SRAT ACPI code
to match the cpx code.
Change-Id: I54675b52aaf2999d884b3c20ccb143fbbf8b138a
Signed-off-by: Marc Jones <marcjones@sysproconsulting.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45847
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Jay Talbott <JayTalbott@sysproconsulting.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This change copies ec_commands.h from Chromium OS EC repo at 7b6cb69db.
The change also drops unneeded empty lines and coverts license header
to SPDX style.
BUG=b:147789962
BRANCH=none
TEST=emerge-asurada coreboot
Change-Id: I9816dab5edb418e76896355a0802c59307c664c4
Signed-off-by: Yidi Lin <yidi.lin@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46403
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
Signed-off-by: Huayang Duan <huayang.duan@mediatek.com>
Change-Id: I8f182fff45806912da2390939a6652932501d7c5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44705
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
|
|
This needs to be saved and restored, otherwise the BSP might have an
inconsistent MTRR setup with regards to the AP's which results in
weird errors and slowdowns in the operating system.
TESTED: Fixes booting OCP/Deltalake with Linux 5.8.
Change-Id: Iace636ec6fca3b4d7b2856f0f054947c5b3bc8de
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46375
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Christian Walter <christian.walter@9elements.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
While MRC.bin does not allocate any memory for DPR by default, it can be
patched to do so. However, the current northbridge code does not account
for DPR and will, among other things, place CBMEM inside it. Even though
this may seem like a good thing, it renders TianoCore unable to boot and
clashes with Intel TXT support (the reason to enable DPR to begin with).
Update memmap.c so that CBMEM top does not fall within DPR. Also, report
DPR as reserved, so that OSes know that the DPR memory is not to be used.
Change-Id: I11f23fd43188f987e35fd61f52587e567496cd78
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45712
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
This function is available for all TXT-capable platforms. Use it.
As it also provides the size of TSEG, display it when logging is on.
Change-Id: I4b3dcbc61854fbdd42275bf9456eaa5ce783e8aa
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46055
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Exposes PcieRpL1Substates to devicetree to allow boards to override this configuration.
Tested on an Acer Aspire VN7-572G (Skylake-U).
Change-Id: I36150858485715016158595c832c142b0582ddb8
Signed-off-by: Benjamin Doron <benjamin.doron00@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39538
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
This comment does not follow any of the styles outlined in the coding
style page of the documentation. Adjust it to match the preferred style.
Change-Id: Idf6d0ea69a08e378266b4256c476580889adfca8
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46428
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
HybridStorageMode FSP UPD needs to be set only for optane storage.
Enabling HybridStorageMode causes some extra delay in FspSiliconInit due
to HECI command and hence is avoided for NVMe and SATA scenerios. This
change disables "HybridStorageMode" for volteer baseboard. For boards
using optane HybridStorage needs to be enabled from overwrite devicetree.
We are enabling HybridStorage for volteer and volteer2 as those plaforms
have SKU's with optane storage.
BUG=b:158573805
TEST=Build and boot non optane device and confirm that FspSiliconInit
time is reduced. This saves ~100ms.
Signed-off-by: Shaunak Saha <shaunak.saha@intel.com>
Change-Id: I54fc78e3f888d4f2a02ba0ad6b9aef33eb872a9c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45643
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Add 64-bit versions of clz, __ffs & log2: `__ffs64`, `__clz64`,
and `log2_64`.
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: Iefc6e6c51f5b20607c88e38660a499a4f77ce0d0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45938
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
