Age | Commit message (Collapse) | Author |
|
Add WiFi SAR table for taniks.
BUG=b:226690925
TEST=build FW and checked SAR table can load by WiFi driver.
Signed-off-by: leo.chou <leo.chou@lcfc.corp-partner.google.com>
Change-Id: I7b52f71b1fe49c02beaa48410495b81661b58fac
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63684
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
commit c6b041a12e refactor the TPM Kconfig. MAINBOARD_HAS_LPC_TPM
has changed to MEMORY_MAPPED_TPM.
Signed-off-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Change-Id: Iff7e20ac271eb5b2afc9061819e2cc0cf2264cbf
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63773
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Ivy Jian <ivy.jian@quanta.corp-partner.google.com>
Reviewed-by: Frank Wu <frank_wu@compal.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Break TPM related Kconfig into the following dimensions:
TPM transport support:
config CRB_TPM
config I2C_TPM
config SPI_TPM
config MEMORY_MAPPED_TPM (new)
TPM brand, not defining any of these is valid, and result in "generic" support:
config TPM_ATMEL (new)
config TPM_GOOGLE (new)
config TPM_GOOGLE_CR50 (new, implies TPM_GOOGLE)
config TPM_GOOGLE_TI50 (new to be used later, implies TPM_GOOGLE)
What protocol the TPM chip supports:
config MAINBOARD_HAS_TPM1
config MAINBOARD_HAS_TPM2
What the user chooses to compile (restricted by the above):
config NO_TPM
config TPM1
config TPM2
The following Kconfigs will be replaced as indicated:
config TPM_CR50 -> TPM_GOOGLE
config MAINBOARD_HAS_CRB_TPM -> CRB_TPM
config MAINBOARD_HAS_I2C_TPM_ATMEL -> I2C_TPM && TPM_ATMEL
config MAINBOARD_HAS_I2C_TPM_CR50 -> I2C_TPM && TPM_GOOGLE
config MAINBOARD_HAS_I2C_TPM_GENERIC -> I2C_TPM && !TPM_GOOGLE && !TPM_ATMEL
config MAINBOARD_HAS_LPC_TPM -> MEMORY_MAPPED_TPM
config MAINBOARD_HAS_SPI_TPM -> SPI_TPM && !TPM_GOOGLE && !TPM_ATMEL
config MAINBOARD_HAS_SPI_TPM_CR50 -> SPI_TPM && TPM_GOOGLE
Signed-off-by: Jes B. Klinke <jbk@chromium.org>
Change-Id: I4656b2b90363b8dfd008dc281ad591862fe2cc9e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63424
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
After assessing the signal integrity, 100 MHz SPI fast speed can be
enabled for SPI ROM.
BUG=b:213403891
BRANCH=guybrush
TEST=Build and boot to OS in Dewatt board version 3.
Change-Id: If0318abf1fed9b1f4ba876f736fdbf92c1ea6933
Signed-off-by: Rob Barnes <robbarnes@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63747
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add FW_CONFIG probe for absent ANPEC APW8738BQBI IC on kracko.
BUG=b:223687184
TEST=emerge-dedede coreboot
Signed-off-by: Robert Chen <robert.chen@quanta.corp-partner.google.com>
Change-Id: Ib12265591e679e6b9ed34299f1256db05147eaef
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63111
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Henry Sun <henrysun@google.com>
Reviewed-by: Shou-Chieh Hsu <shouchieh@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
Add FW_CONFIG probe for absent ANPEC APW8738BQBI IC on drawcia.
BUG=b:223687184
TEST=emerge-dedede coreboot
Change-Id: I683049e9d2b10fc9455ef782ce798f1c453073bc
Signed-off-by: Robert Chen <robert.chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63110
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Henry Sun <henrysun@google.com>
Reviewed-by: Shou-Chieh Hsu <shouchieh@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
Add FW_CONFIG probe for absent ANPEC APW8738BQBI IC on lantis.
BUG=b:223687184
TEST=emerge-dedede coreboot
Signed-off-by: Robert Chen <robert.chen@quanta.corp-partner.google.com>
Change-Id: I3d8eec1d2f962d42f3be225eef8498e8b722aace
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63112
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Shou-Chieh Hsu <shouchieh@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
Fix WLAN PCIE speed to GEN2. Dynamic switching between speeds is causing
the PSP to hang when resuming from S0ix suspend. The root cause is still
under investigation. Just disabling PSPP fixes the hang but causes poor
PLT performance.
BUG=b:228830362
BRANCH=guybrush
TEST=suspend_stress_test on AC and DC
Change-Id: I988365e51aca0d6515c5605b3032521cf59d8d30
Signed-off-by: Rob Barnes <robbarnes@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63722
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Kevin Chiu <kevin.chiu.17802@gmail.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add FW_CONFIG STORAGE and probe for UNKNOWN, NVME and eMMC.
BUG=b:220039297
TEST=emerge-brask coreboot.
Signed-off-by: Raihow Shi <raihow_shi@wistron.corp-partner.google.com>
Change-Id: If83031edcd90ea746704590765102b9b0dee03c1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63080
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Zhuohao Lee <zhuohao@google.com>
|
|
This patch implements two APIs to perform LPC/eSPI write protect enable/
disable operation using PCI configuration space register 0xDC
(BIOS Controller).
BUG=b:211954778
TEST=Able to build and boot google/redrix to OS.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I8ce831218025a1d682ea2ad6be76901b0345b362
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63687
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
|
|
This patch performs additional SPI lock configuration as per Intel
Flash Security Specification.
BUG=b:211954778
TEST=Able to build google/brya and verified all flash security
recommendations are being met.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I922db8b46ac0d0523b91fc5aced88e38c8d8a560
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63627
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
This patch drops unused LPC BIOS control macros.
BUG=b:211954778
TEST=Able to build and boot google/hatch.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: Ib309c6bd0f27115357f8e62200808764748f51a6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63688
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Alder Lake-N has single memory controller with 64-bit bus width. Alder
Lake common meminit block driver considers bus width to be 128-bit and
populates the meminit data accordingly. By setting half_populated to
true, only the bottom half is populated.
Ideally, half_populated is used in platforms with multiple channels to
enable only one half of the channel. Alder Lake N has single channel,
and it would require for new structures to be defined in meminit block
driver for LPx memory configurations. In order to avoid adding new
structures, set half_populated to true. This has the same effect as
having single channel with 64-bit width.
BRANCH=NONE
TEST=Build and boot ADL-N RVP.
Signed-off-by: Usha P <usha.p@intel.com>
Change-Id: I2ecc3018a1ab039990ba47898ff0e0e2ede695cc
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62913
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Looks like the `notify_data` struct array idea comes from the FSP 2.0
notify driver, which has a similar struct but with several additional
fields. However, there's no need for this mechanism in the CSE driver
because the struct only contains a condition (boolean) and a function
to execute, which can be expressed as a regular if-block.
Change-Id: I65fcb2fc02ea16b37c764f1fd69bdff3382fad18
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63708
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Taeko/Tarlo uses the WIFI_SAR_ID field in FW_CONFIG to pick which
SAR table to load.
BUG=b:226684990
TEST=emerge-brya coreboot
Cq-Depend: chrome-internal:4676926, chrome-internal:4686953
Signed-off-by: Joey Peng <joey.peng@lcfc.corp-partner.google.com>
Change-Id: I9852553f5c91494db845d45a94e2566248538bba
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63644
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
Add supported memory parts in mem_parts_used.txt, and generate
SPD id for these parts.
MT53E512M32D1NP-046 WT:B (Micron)
MT53E1G32D2NP-046 WT:B (Micron)
H54G46CYRBX267 (Hynix)
H54G56CYRBX247 (Hynix)
K4U6E3S4AB-MGCL (Samsung)
K4UBE3D4AB-MGCL (Samsung)
BUG=None
TEST=build pass
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Change-Id: I1fbdce203afd282cef9fcd7aebbace69d19fbbf1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63706
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Create the osiris variant of the brya0 reference board by copying
the template files to a new directory named for the variant.
(Auto-Generated by create_coreboot_variant.sh version 4.5.0).
BUG=b:229352299
BRANCH=None
TEST=util/abuild/abuild -p none -t google/brya -x -a
make sure the build includes GOOGLE_OSIRIS
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Change-Id: I41e088a3415add86cba87c919af23494f816bb24
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63650
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I530bb217bb9a944990232dcf4e08f160b5267512
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55008
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Update SPI setting as below:
Normal speed:33mhz
Fast speed:66mhz
Alt speed:66mz
TPM speed:33mhz
BUG=b:225213679
TEST=boot skyrim and verify spi settings.
Signed-off-by: Chris.Wang <chris.wang@amd.corp-partner.google.com>
Change-Id: Icbe4b9f4794f7e883c3819258ede809c3c8922b0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63717
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
Increase RFI Spread Spectrum to 6% for Vell as RF team request. The
default of Spread Spectrum in FSP is 1.5%, and set 1.5% in baseboard
as default.
BUG=b:228929196
TEST=emerge-brya coreboot and pass RF test as before
Change-Id: I7cdca8f51ad18f4ab03e4e6c744b60da68263ce2
Signed-off-by: Robert Chen <robert.chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63440
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Enable SPI dTPM using eSPI bus.
Signed-off-by: Lean Sheng Tan <sheng.tan@9elements.com>
Change-Id: I18ca41c143ade024ee2840b619ba777b22a2a86a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63720
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
The PCI Local Bus Specification Revision 3.0 requires that
multi-function devices always implement function 0. Because of
this, enabling UFS (PCI device 12.7) requires ISH (PCI device 12.0)
to be enabled as well.
Signed-off-by: Lean Sheng Tan <sheng.tan@9elements.com>
Change-Id: Ia8b9561973640edc5f7d0f579dd640e805c0af17
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63719
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Signed-off-by: Lean Sheng Tan <sheng.tan@9elements.com>
Change-Id: I3f438a7b1dff1a44a81edc8adc983d08708fdd57
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63718
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
In order to enable the UFS controller (PCI device 12.7), the PCI
specification says that the device at function 0 in the same slot must
also be enabled, which is the ISH. Therefore, this CL enables both
the UFS controller and ISH.
TEST=Boot to kernel and check lspci output
00:12.0 Serial controller: Intel Corporation Device 54fc
00:12.7 Mass storage controller [0109]: Intel Corporation
Device 54ff
Signed-off-by: Meera Ravindranath <meera.ravindranath@intel.com>
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Change-Id: If15bcaffc8fd3bbbe4b181820993ab2d882bbbe1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62662
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Reviewed-by: Kangheui Won <khwon@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Configure GPP_R0, GPP_R1, GPP_R2 and GPP_R3 for headset function
enable with ALC5682I+MAX98360.
BUG=b:202671753
BRANCH=firmware-brya-14505.B
TEST=emerge-brya coreboot
Change-Id: I93070a8096d43557a50e5a545227f2906e299d8e
Signed-off-by: Amanda Huang <amanda_hwang@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63721
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Frank Wu <frank_wu@compal.corp-partner.google.com>
|
|
Based on the latest schematic, exchange I2C port for TPM/touchscreen.
TPM: I2C3 -> I2C1
Touchscreen: I2C1 -> I2C3
BUG=b:202671753
TEST=emerge-brya coreboot
Change-Id: Ifa6235869f34e0038a8ecad33d59654626cf7815
Signed-off-by: Amanda Huang <amanda_hwang@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63709
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Frank Wu <frank_wu@compal.corp-partner.google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
This reverts commit d80d88c0fec96b2fff93db87d0c83f4c6754ae7a.
Reason for revert: 100Mhz should only be enabled on DeWatt
on board version >=3. Enabling it on board version 2 will
cause failures.
BUG=b:213403891
BRANCH=guybrush
TEST=Build dewatt
Change-Id: I0b6acd2cda2af35ff33e89e3b339731e35d72cb1
Signed-off-by: Rob Barnes <robbarnes@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63746
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Packing structs will result in unaligned sizes, possible causing
problems for other entries.
Change-Id: Ifb756ab4e3562512e1160224678a6de23f3b84ec
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63714
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: Ie874fe2c023157fad0adc021faa45e70822208da
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63711
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
The `_PRS` ACPI object is not needed for static (non-configurable)
devices. For devices where `_CRS` always provides the same set of
resource settings, drop the `_PRS` object. Note that every dropped
`_PRS` object only provides one set of resource settings, which is
identical to the resource settings provided by the `_CRS` object.
Also, drop `IGNORE_IASL_MISSING_DEPENDENCY` as it's no longer needed.
Change-Id: If56267e8a68897236d5ff73322317cbef7ab2243
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63528
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
The `_PRS` ACPI object is not needed for static (non-configurable)
devices. For devices where `_CRS` always provides the same set of
resource settings, drop the `_PRS` object. Note that every dropped
`_PRS` object only provides one set of resource settings, which is
identical to the resource settings provided by the `_CRS` object.
The no-op `_DIS` methods can also be removed for the same reason.
Also, drop `IGNORE_IASL_MISSING_DEPENDENCY` as it's no longer needed.
Change-Id: I7e702e9318fbf68dbd883a145111e6beb6815b8b
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63527
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
The `_PRS` ACPI object is not needed for static (non-configurable)
devices. For devices where `_CRS` always provides the same set of
resource settings, drop the `_PRS` object. Note that every dropped
`_PRS` object only provides one set of resource settings, which is
identical to the resource settings provided by the `_CRS` object.
Also, drop `IGNORE_IASL_MISSING_DEPENDENCY` as it's no longer needed.
Change-Id: Ic37608ac9622b37cae6d81045740a033e9aa9d4f
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63526
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
This should no longer be needed because the ASL has been fixed.
Change-Id: I4d1500217bef54fa3d2be397e5e2a155da3f965d
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63525
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
The `_PRS` ACPI object is not needed for static (non-configurable)
devices. For devices where `_CRS` always provides the same set of
resource settings, drop the `_PRS` object. Note that every dropped
`_PRS` object only provides one set of resource settings, which is
identical to the resource settings provided by the `_CRS` object.
Change-Id: Ief40e790fdee336fd6c786e18cd01c41fa658c2c
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63521
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
|
|
The `_PRS` ACPI object is not needed for static (non-configurable)
devices. For devices where `_CRS` always provides the same set of
resource settings, drop the `_PRS` object. Note that every dropped
`_PRS` object only provides one set of resource settings, which is
identical to the resource settings provided by the `_CRS` object.
In addition, drop `IGNORE_IASL_MISSING_DEPENDENCY` from the two
mainboards using the MEC1308 code, `samsung/{lumpy, stumpy}`.
Change-Id: I5d5cdc28c2cfaa5dfcffd656060b931208977386
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63523
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
The `_PRS` ACPI object is not needed for static (non-configurable)
devices. For devices where `_CRS` always provides the same set of
resource settings, drop the `_PRS` object. Note that every dropped
`_PRS` object only provides one set of resource settings, which is
identical to the resource settings provided by the `_CRS` object.
In addition, drop `IGNORE_IASL_MISSING_DEPENDENCY` from the only
mainboard using the SCH5545 code, `dell/snb_ivb_workstations`.
Change-Id: Ic462bd3dfa287744d4f733561de81c09c1c397e6
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63522
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
The `_PRS` ACPI object is not needed for static (non-configurable)
devices. For devices where `_CRS` always provides the same set of
resource settings, drop the `_PRS` object. Note that every dropped
`_PRS` object only provides one set of resource settings, which is
identical to the resource settings provided by the `_CRS` object.
The no-op `_DIS` methods can also be removed for the same reason.
Also, drop `IGNORE_IASL_MISSING_DEPENDENCY` as it's no longer needed.
Change-Id: I71275f2581b999d606f36773578b36dbdccf6452
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63524
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Add PROP method under \_SB.DPTF.TPWR scope which will return static
worst case rest of platform power in miliWatts.
This value is static, which has to configured from devicetree of
overridetree for each platform
BUG=b:205928013
TEST=Build, boot brya0 and dump SSDT to check PROP method
Scope (\_SB)
{
Device (DPTF)
{
Device (TPWR)
{
Method (PROP, 0, Serialized)
{
Return (XXXX)
}
}
}
}
Signed-off-by: Varshit B Pandya <varshit.b.pandya@intel.com>
Change-Id: I1415d2a9eb55cfadc3a7b41b53ecbec657002759
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63697
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
1. Remove dmi.h as it's migrated as gpmr.header
2. Remove unused gpmr definitions
3. For old platforms, define DMI defintions in c code
for less code changes.
TEST=Build
Signed-off-by: Wonkyu Kim <wonkyu.kim@intel.com>
Change-Id: Ib340ff1ab7fd88b1e7b3860ffec055a75e562de7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63472
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
This patch migrates GPMR driver over DMI to accommodate future SOCs
with different interface (other than PCR/DMI).
TEST=Able to build and boot google/redrix.
Signed-off-by: Wonkyu Kim <wonkyu.kim@intel.com>
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I00ac667e8d3f2ccefd8d51a8150a989fc8e5c7e2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63471
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
This alias name is required for the mainboard.c code to generate the
appropriate power-off seqeuence for use during orderly S5 shutdown
from the OS. It had been accidentally removed, but is required, so
this patch adds it.
BUG=b:227788351
TEST=compile
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: I8936a01bd3a6b908033a8c58bd4e84b30d199e98
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63556
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
Disable SATA config from devicetree for ADL-N RVP, since we are not
planning to use it in chrome config.
Signed-off-by: Usha P <usha.p@intel.com>
Change-Id: Ic9dce3a0b06e1a0d0d9fa495aa406eb12557d842
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63443
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kangheui Won <khwon@chromium.org>
|
|
Change-Id: Idefbe15c5f7c7169d9b60079b90cd02affb261ca
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63701
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Configure the power saving pin for Smart Card.
BUG=b:229356121
TEST=emerge-brya coreboot chromeos-bootimage
Change-Id: Ia17970f717c6ba806d9603031c486bad86e42b37
Signed-off-by: Wisley Chen <wisley.chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63648
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
After assessing the signal integrity, 100 MHz SPI fast speed can be
enabled for SPI ROM.
BUG=b:213403891
TEST=Build and boot to OS in Dewatt board version 2.
Signed-off-by: Kenneth Chan <kenneth.chan@quanta.corp-partner.google.com>
Change-Id: I7301d873e36bec4ee46c9d18293f924500ea9aba
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63685
Reviewed-by: Rob Barnes <robbarnes@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Treat dimm addr_map 0 non-existent. addr_map default is 0, we don't set
it if Hw is not present. Also change the test case default to avoid 0.
SODIMM SMbus address 0x50 to 0x53 is commonly used.
BUG=b:213964936
BRANCH=firmware-brya-14505.B
TEST=emerge-brya coreboot chromeos-bootimage
The MRC training does not be performed again after rebooting.
Signed-off-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Change-Id: I2ada0109eb0805174cb85d4ce373e2a3ab7dbcac
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63628
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Frank Wu <frank_wu@compal.corp-partner.google.com>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
BUG=None
TEST=Build and boot to OS in Skyrim. Ensure that the XHCI controllers
are enumerated successfully and ACPI device objects are added in SSDT.
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Change-Id: I7ad4555212ed38ea0f9029275345e4945855a8c3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63641
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jon Murphy <jpmurphy@google.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
The patch disables PCH USB2 Phy power gating to prevent possible display
flicker issue for felwinter board. Please refer Intel doc#723158 for
more information.
BUG=b:221461379, b:226020977
TEST=Verify the build for felwinter board
Signed-off-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Change-Id: I25033ea218fa3154eb99af6be43c4198f4db3bcb
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63294
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
Add conn1 for pch_espi and add type-c port2 for pmc_mux.
BUG=b:220814038
TEST=emerge-brask coreboot.
Signed-off-by: Raihow Shi <raihow_shi@wistron.corp-partner.google.com>
Change-Id: Idfd7b761496a110f34838abb0fd408b37d390ba2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63570
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
This CL adds the delay time 50 ms and 20 ms into the RTD3 sequence,
the reason is that the rise and fall times of each signal
may differ by board, and so those board-specific delays
must be taken into account when power sequencing.
We checked power on sequence requires enable pin prior to reset pin,
so added delay to meet the sequence.
Based on BH799BB_Preliminary_DS_R079_20201124.pdf in chapter 7.2.
BUG=b:228907551
TEST=emerge-brask coreboot.
Signed-off-by: Raihow Shi <raihow_shi@wistron.corp-partner.google.com>
Change-Id: Idecb1c89655c9b8b720c3c65efc77e06e6a8b300
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63544
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Remove i2c1 because brask devicetree is already has it.
BUG=b:220814038
TEST=emerge-brask coreboot.
Signed-off-by: Raihow Shi <raihow_shi@wistron.corp-partner.google.com>
Change-Id: Ic782e1c6434ac57bdf65b3d9f4219bdf32d25b9e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63545
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Enable pen garage. Pen detect is active low.
BUG=b:229168203
TEST:Build and boot to OS in skyrim. Evtest work as expected
Input driver version is 1.0.1
Input device ID: bus 0x19 vendor 0x1 product 0x1 version 0x100
Input device name: "PRP0001:00"
Supported events:
Event type 0 (EV_SYN)
Event type 5 (EV_SW)
Event code 15 (SW_PEN_INSERTED) state 1
Properties:
Testing ... (interrupt to exit)
Event: time 1649922170.578779, type 5 (EV_SW), code 15 (SW_PEN_INSERTED), value 0
Event: time 1649922170.578779, -------------- SYN_REPORT ------------
Event: time 1649922172.070740, type 5 (EV_SW), code 15 (SW_PEN_INSERTED), value 1
Signed-off-by: Ian Feng <ian_feng@compal.corp-partner.google.com>
Change-Id: I3bb07af6aebdc355a73148d8be79b1014147f61d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63633
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Add Goodix touchscreen according to the Programming Guide Rev.0.7
BUG=b:228907558
TEST=local build and tested with Goodix touch screen
Change-Id: I35dd3ca76e9e0f17508bef46c90b53b4be5d0033
Signed-off-by: Ian Feng <ian_feng@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63573
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Fix the issue that can't hear the boot beep at dev screen. GPP_B14 is
used for PWM_PP3300_BUZZER and it should set to GPO. Modify GPP_B14 from
PAD_CFG_NF_LOCK to PAD_CFG_GPO_LOCK.
BUG=b:229345416
BRANCH=firmware-brya-14505.B
TEST=emerge-brask coreboot and verify if the buzzer beeps.
Signed-off-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Change-Id: I601735ab20974cd992ca5dd6dbaca1517a395aa2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63645
Reviewed-by: Frank Wu <frank_wu@compal.corp-partner.google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Pick specific VBTs for HDMI, DP, and ABSENT according to FW_CONFIG.
BUG=b:220241277
TEST=emerge-brask coreboot.
Signed-off-by: Raihow Shi <raihow_shi@wistron.corp-partner.google.com>
Change-Id: Icc8fbef1467605505459fce264697f670591c81e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63604
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
select DRIVERS_GENESYSLOGIC_GL9750 to disable ASPM L0s.
BUG=b:229213455
TEST=emerge-brya coreboot chromeos-bootimage
Signed-off-by: Wisley Chen <wisley.chen@quanta.corp-partner.google.com>
Change-Id: Ie89fa6c66974284063cd25ae8097db94a93326ca
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63638
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
This is a property of a platform and should not be exposed to the
user.
Change-Id: I34f9097d40b2bf732cecf30bf13ba5a413dd53a5
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63676
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
None of these options make sense on different ARCH.
Change-Id: Ie90ad24ff9013e38c42f10285cc3b546a3cc0571
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63673
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Insert CSE timestamps to coreboot timestamp table.
BUG=b:182575295
TEST=Boot to OS on Brya Redrix board.
Signed-off-by: Bora Guvendik <bora.guvendik@intel.com>
Change-Id: Ifbea7155a294e0039a5bd1d16588775e90a29ae3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63616
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Followed the Brya series to lock the gpio pins in baseboard. Variant
should honor locked gpios from baseboard, but not the last. Variant can
add more gpios to lock if needed.
BUG=b:216671701
TEST='emerge-nissa coreboot chromeos-bootimage', flash and verify that
nivviks boots successfully to kernel.
Signed-off-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Change-Id: Ib34ca287596a6958407a944d0caf53f4bcc60d9b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63568
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Kangheui Won <khwon@chromium.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
Add TPM I2C for crota to avoid TPM I2C fail.
BUG=b:229200525
TEST=emerge-brask coreboot.
Signed-off-by: Raihow Shi <raihow_shi@wistron.corp-partner.google.com>
Change-Id: I8054e623fb0c3c549c3373982ce9d4fbd57e0fd7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63635
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Add TPM I2C for crota to avoid TPM I2C fail.
BUG=b:226315394
TEST=USE="project_crota emerge-brya coreboot" and verify it builds
without error.
Signed-off-by: Terry Chen <terry_chen@wistron.corp-partner.google.com>
Change-Id: I7eb3ce6c2faf857c8f5d789af395e315caea4102
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63617
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
update STT setting for dewatt.
BUG=b:228040295
BRANCH=guybrush
TEST=build, verify the parameter has been applied to
the system by checking the AGT tool.
Signed-off-by: Chris.Wang <chris.wang@amd.corp-partner.google.com>
Change-Id: Id319d42747dd0d5f6a9ca727635d85e6b9bd65af
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63699
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
This patch creates a helper function to set SPI controller VCL bit as
recommended by Intel Flash Security Specification.
BUG=b:211954778
TEST=Able to build google/brya and verified that SPI flash controller
MMIO register 0xC4 bit 30 is set.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: Ie9a12db1bab81779fd8e7db90221d08da3c65011
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63626
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marc Jones <marc@marcjonesconsulting.com>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
This patch creates a helper function to clear HSFSTS_CTL (offset 0x04)
register Bits 0 to 4.
As per Intel PCH BIOS spec section 3.6 Flash Security Recommendation,
it's important to clear all SPI outstanding status before setting SPI
lock bits.
BUG=b:211954778
TEST=Able to build google/brya with this patch and clear SPI controller
HSFSTS_CTL register Bits 0 to 4.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I62adba0d0cef1d4c53b24800f90b4fe76a9d78b7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63625
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
This patch creates a helper function to check if any SPI transaction
is pending.
As per Intel PCH BIOS spec section 3.6 Flash Security Recommendation,
it's important to ensure there is no pending SPI transaction before
setting SPI lock bits.
BUG=b:211954778
TEST=Able to build google/brya with this patch and no error msg seen
due to `SPI transaction is pending`.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: Ibd3f67ae60bfcb3610cd0950b057da97ff74b5b9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63624
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
BUG=b:211954778
TEST=None
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: Ib8cc4b8d13b61e3935f2050d25ce0278162c91c4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63629
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
This patch converts whitespace into tabs to maintain the uniformity
across the fast_spi_def.h file.
BUG=b:211954778
TEST=Able to build google/brya.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I56bcd263c6a5c0036e459926a25538e3448fbce6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63623
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
|
|
Remove EC_ENABLE_LID_SWITCH since this causes a duplicate SW_LID
entries. The other SW_LID entry is generated by MKBP.
BUG=b:228907256
BRANCH=guybrush
TEST=Lid open close triggers events on Nipperkin
Change-Id: I5c1cf7aeac8405bce7bfc77110eceaf3e5383fe7
Signed-off-by: Rob Barnes <robbarnes@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63658
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Robert Zieba <robertzieba@google.com>
Reviewed-by: Jon Murphy <jpmurphy@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
BUG=b:227296841
BRANCH=guybrush
TEST=emerge-guybrush coreboot chromeos-bootimage
pass PLT criteria: S0 > 600ms, s0i3 > 14 days
Change-Id: I9c61e1d0f3db8b9885040255d6de266616768b68
Signed-off-by: Kevin Chiu <kevin.chiu.17802@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63537
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Rob Barnes <robbarnes@google.com>
Reviewed-by: Jon Murphy <jpmurphy@google.com>
|
|
This is based on previous work done by a good friend of mine.
The notable differences between this board and the SFF variant is that:
- CMT has 4 more PCI/PCIe ports than SFF.
- CMT has 2 more SATA ports than SFF.
TESTED on Z220 CMT Workstation (boots to payload)
Change-Id: I2b298921e6f509440ec7b049e086c0878f708bd3
Signed-off-by: Damien Zammit <damien@zamaudio.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62809
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Edward O'Callaghan <quasisec@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Built lenovo/t440p with BUILD_TIMELESS=1 and coreboot.rom remains the
same.
Change-Id: I7bac7ad5236346a3c2a8928ecdfadde6564ff232
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63429
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Change-Id: Ie772701192a3589b51642df446f0b2527fb7d630
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63428
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
|
|
Set the BT USB device to use GPIO for the power status. This causes an
ACPI `_STA()` function to be generated that returns the power status of
the BT USB device, rather than always returning `0x1`. This `_STA()`
function can be used during boot to skip enabling the device (and
performing the associated sleep) if the device is already powered on.
BRANCH=None
BUG=b:225022810
TEST=Dump SSDT table for guybrush
Signed-off-by: Tim Van Patten <timvp@google.com>
Change-Id: I72f6b28671efddfbef53f328d904a05f73f39efa
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63559
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
If the device has enabled `use_gpio_for_status`, then call the `_STA`
method in `_ON` to determine if the device is already enabled. If it is
already enabled, return early to skip re-enabling the device and
performing the associated sleep.
This change is necessary since the Linux kernel does not call `_STA`
before calling `_ON`.
BRANCH=None
BUG=b:225022810
TEST=Dump SSDT table for guybrush
Signed-off-by: Tim Van Patten <timvp@google.com>
Change-Id: I13aa41766555953b86eded4c72e3b317fe6db5c8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63613
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add the member `use_gpio_for_status` to the structure
`drivers_usb_acpi_config`, so the `devicetree.cb` can specify it.
This field is then used to initialize the corresponding field in the
structure `acpi_power_res_params` in `usb_acpi_fill_ssdt_generator()`.
The member `acpi_power_res_params::use_gpio_for_status()` is already
being used by `acpi_device_add_power_res()` to determine which version
of the `_STA()` method to output.
BRANCH=None
BUG=b:225022810
TEST=Dump SSDT table for guybrush
Signed-off-by: Tim Van Patten <timvp@google.com>
Change-Id: I69eb5f1ad79f3b2980f43dcf4a36585fca198ec9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63558
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
Replace 'struct lb_uint64' with 'typedef __aligned(4) uint64_t
lb_uint64_t', and remove unpack_lb64/pack_lb64 functions since it's no
longer needed.
Also replace 'struct cbuint64' with 'cb_uint64_t' and remove
'cb_unpack64' in libpayload for compatible with lb_uint64_t.
Signed-off-by: Jianjun Wang <jianjun.wang@mediatek.com>
Change-Id: If6b037e4403a8000625f4a5fb8d20311fe76200a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63494
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
Update the build scripts to inject variant specific SPDs into APCB.
BUG=None
TEST=Build and boot to OS in Skyrim boards with all the concerned memory
parts.
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Change-Id: I3b3f6f248d54681c6f55c00660d1f2988ae906ba
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63600
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add supported memory parts and generate the associated DRAM part ID.
Also for MT62F2G32D8DR-031 WT:B memory part, add a custom SPD that
configures the DRAM speed at 5500 MHz. Use this custom SPD until that
part can operate at full speed (i.e. 6400 MHz).
BUG=None
TEST=Build Skyrim.
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Change-Id: Id87e79f5d6187d57d74487841c09aa309f1450b4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63599
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Robert Zieba <robertzieba@google.com>
Reviewed-by: Jon Murphy <jpmurphy@google.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
Setup the following acoustic noise mitigation features:
1) Slew rate for both IA and GT domains to 1/8
2) Disable Fast package C ramp
BUG=b:229046516
TEST=build and verified by power team
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Change-Id: Ifb5700391e33818878994f205acae7ee3b1b96d9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63610
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Update Kconfig per Atlas usages:
1. Set EC I/O mapped UART as default UART output
2. Add EC IFD region & ACPI support
Signed-off-by: Lean Sheng Tan <sheng.tan@9elements.com>
Change-Id: I970de724237bcb08899aed7a4b87a23c5cdb0b48
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63464
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Christian Walter <christian.walter@9elements.com>
|
|
PSP needs SPL file to boot. Introduce the support to add SPL file.
Currently Sabrina does not have a specific SPL file. Use Cezanne SPL
file as a placeholder.
BUG=b:224618411
TEST=Build and boot to OS in Skyrim after adding Sabrina specific SPL
file.
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Change-Id: I222bb81b2babddc778b2cff858ef7979f85ac0e6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63313
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Disable PSPP parameters for WLAN card on Nipperkin. This feature
is causing S0ix resume hangs.
BUG=b:227296841,b:228830362
BRANCH=guybrush
TEST=Suspend stress test passes on Nipperkin
Signed-off-by: Rob Barnes <robbarnes@google.com>
Change-Id: I38f05b92ace4aba61163194a6a638915882b8871
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63593
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The printed address ranges in the tree (resource allocator and even
some MTRR code) usually shows the range inclusive (meaning from start
address to the real end address of the range). Though there is still
some code in the MTRR context which prints the ranges with an exclusive
end. This patch aligns the printing of ranges in the MTRR code to be
consistent among the tree so that the shown end addresses are now
inclusive.
Change-Id: I0ca292f9cf272564cb5ef1c4ea38f5c483605c94
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63541
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Christian Walter <christian.walter@9elements.com>
|
|
Some brya variants may need to initialize and finalize some
variant-specific devices during ramstage, therefore add the
commonly-used hooks and callbacks to support this.
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: Iede6dc5a5b9a7385fedd59d4eeaaba118eff0e20
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62382
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Add PAD_CFG_GPI_SCI_LOW_LOCK and PAD_CFG_GPI_SCI_HIGH_LOCK macro
to support mainboard to lock NC and GPI_SCI pins as applicable.
BUG=b:216583542
TEST=build passed
Signed-off-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Change-Id: I5060777cc09af6cb3144ad799154e77167521de3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63569
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
This patch renames all required IA common code blocks and PCH configs
from DMI to GPMR.
TEST=Able to build and boot google/redrix.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: Ic6e576dd7f207eb16d90c5cc2892d919980d91c4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63608
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
This patch enhances the GPMR driver to add public APIs for other IA
common code drivers and/or SoC code to utilize.
Also, migrated all PCR GPMR register definitions into the common
`pcr_gpmr.h` header file.
TEST=Able to build and boot google/redrix.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I87dca55a068366cb9a26a5218589166c1723da7f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63607
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
As a start of GPMR(General Purpose Memory Range) driver migration,
1. rename dmi folder to gpmr folder
2. rename dmi.c to gpmr.c
TEST=build
Signed-off-by: Wonkyu Kim <wonkyu.kim@intel.com>
Change-Id: I4d57f4b8bd06e0cf6c9afa4baf4a7bed64ecb56b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63170
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
|
|
If verified boot uses 2 RW FW slots, configure amdfwtool to maintain
single copy of PSP Level2 entries.
BUG=None
TEST=Build and boot to OS in Skyrim.
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Change-Id: I94eea693139b714c321b4be89380342ec7a21222
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63510
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
Previously, clock_configure() will configure the clocks to round up to
the next highest frequency bin. This seems non-intuitive. Changing
the logic to find an exact frequency match and will halt booting if no
match is found. Recently fixed a bug in CB:63311, where the clock was
being set incorrectly for emmc and was able to find it because of this
stricter check.
BUG=b:198627043
BRANCH=None
TEST=build herobrine image and try to set SPI frequency to number not
supported. Ensure device doesn't boot.
Change-Id: I9cfad7236241f4d03ff1a56683654649658b68fc
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63289
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <patrick@coreboot.org>
|
|
This patch adds `xhci_host_reset()` to reset XHCI controller and the
scope of this function is with SMM hence, compiling xhci.c for SMM as
well.
Also, refactored `xhci.c` code to keep PCI enumeration within the scope
of `ramstage` alone hence, guarded with `ENV_RAMSTAGE` env_variable.
BUG=b:227289581
TEST=Able to perform a call from `xhci_host_reset` from S5 smi handler.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: Ie0dc0a64044f291893931726d26c08c8b964a3cc
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63551
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch calls into need_restore_mtrr() from the mtrr_use_temp_range
function to set `put_back_original_solution` to discard any temporary
MTRR range prior to boot to payload.
BUG=b:225766934
TEST=Able to build and boot google/brya to verify that
`remove_temp_solution()` is able to discard any temporary MTRR range
before booting to payload.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I2e00ec593847e1eb173d5ac77b15b50342860f89
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63491
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
`put_back_original_solution` variable in mtrr.c is static, but there is
a need to set put_back_original_solution outside of mtrr.c in order to
let `remove_temp_solution` to drop any temporary MTRRs being set
outside `mtrr_use_temp_range()`, for example: `set_var_mtrr()` function
is used to set MTRRs for the ROM caching.
BUG=b:225766934
TEST=Able to build and boot google/redrix.
Change-Id: Ic6b5683b2aa7398a5e141f710394ab772e9775e7
Signed-off-by: Kane Chen <kane.chen@intel.corp-partner.google.com>
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63485
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
BUG=b:228448327
BRANCH=guybrush
TEST=emerge-guybrush coreboot chromeos-bootimage
check ACPI device "LCD" in SSDT
Signed-off-by: Kevin Chiu <kevin.chiu.17802@gmail.com>
Change-Id: I42c5abdbe3bfab72016d56399278a7aff9e33377
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63575
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Rob Barnes <robbarnes@google.com>
|
|
This patch fixes an issue introduced by CB:59195 when QcLib
doesn't return a mem_chip_info structure to coreboot, and
solves some other minor leftover issues from that patch.
BUG=b:182963902,b:177917361
TEST=Validated on qualcomm sc7280 development board
Signed-off-by: Ravi Kumar Bokka <rbokka@codeaurora.org>
Change-Id: I0d59669adaf287d0eb7b58ccb0fe3f98e3d23281
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63026
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
We don't want to enable the speaker on init. It will be enabled while
using GPIO AMP codec in depthcharge.
BUG=b:223289882
TEST=boot Nipperkin and Dewatt and then verify the devbeep and gpio
values in kernel
Signed-off-by: Yu-Hsuan Hsu <yuhsuan@google.com>
Change-Id: Id874421d7464b15be6e521576696bb97e6b22d6a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63540
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
UFS(Universal Flash Storage) is the next generation storage standard and
a SCSI storage technology. It is also a successor of eMMC.
Following changes are needed to add support for UFS -
1) Add UFS controller to chipset.cb and keep it off by default
2) Hook up FSP enable UPD for UFS #1 to the device from chipset.cb
Signed-off-by: Meera Ravindranath <meera.ravindranath@intel.com>
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Change-Id: I92f024ded64e1eaef41a7807133361d74b5009d4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62856
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Kangheui Won <khwon@chromium.org>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
The patch adds mechanism in the Alder Lake SoC code to control PCH
USB2 Phy power gating from brya board variant's devicetree. Please refer
Intel doc#723158 for more information.
BUG=b:221461379
TEST=Build and boot Gimble board
Signed-off-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Change-Id: I3d80a3e36c6f8a3c0f174f955b11457752809f4d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63293
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
Before:
[DEBUG] dw_i2c: SoC 400/3000 ns Bus: 400/1000000 ns
[DEBUG] dw_i2c: period 334 rise 13 fall 2 tlow 174 thigh 80 spk 7
[DEBUG] dw_i2c: hcnt = 104 lcnt = 202 sda hold = 7
After:
[DEBUG] dw_i2c: SoC 400/3000 ns Bus: 400/1000000 ns
[DEBUG] dw_i2c: period 334 rise 13 fall 2 tlow 174 thigh 80 spk 7
[DEBUG] dw_i2c: hcnt = 104 lcnt = 202 sda hold = 7
BUG=None
TEST=Check that the formatting looks correct, as above.
Change-Id: I6703a5d6512cee7848edae27afcfd82eb89bcacb
Signed-off-by: Reka Norman <rekanorman@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63563
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kangheui Won <khwon@chromium.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|