| Age | Commit message (Collapse) | Author |
|---|
|
ExtINT is related to external PIC mode i8259 interrupts,
they should be delivered to one CPU (BSP) only.
Change-Id: I78490d2cbe3d9f52e10ef2471508263fd6c146ba
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42434
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Picasso and Cezanne define and use APU_I2C[01234]_BASE for the base
addresses of the I2C controllers, so align Stoneyridge with this. The
ACPI device names aren't changed from I2C[ABCD] to I2C[0123] for now
since this might change behavior in the OS and would also change the
resulting binary of a timeless build.
TEST=Timeless build results in identical image for Google/Treeya.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I9c400c073eba5c14bd35703b717f75df89a8719d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58370
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Denverton-NS supports uCode PM Timer emulation, according to Intel
doc#558579 rev2.2. Thus, enable it.
Change-Id: I21f55816da9f5e240fdf01a0e92b67b09ef38599
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57944
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Since ACPI 5.0A it is allowed to disable the ACPI Timer, when the
according FADT flag `ACPI_FADT_PLATFORM_CLOCK` is unset.
Starting with Skylake, most platforms (except Xeon-SP) support PM Timer
emulation, so even legacy OSes and payloads should work fine with the
hardware PM Timer disabled. However, when the `TMR_STS` functionality
is required, some legacy OSes might still not work (properly).
Add a note about this to the Kconfig help.
Change-Id: I53f1814113902124779ed85da030374439570688
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58018
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Lance Zhao
|
|
The FADT contains a flag `ACPI_FADT_PLATFORM_CLOCK` telling the OSPM if
a specification-compliant PM Timer is present. Currently, this flag is
set regardless of the timer being enabled or disabled.
To be specification-compliant, only set that flag, when the hardware PM
Timer is enabled. This changes behaviour of all mainboards defaulting to
USE_PM_ACPI_TIMER=n.
Note: On platforms supporting uCode PM ACPI Timer emulation, this is
required, too, because emulation does not support `TMR_STS`. Any
OS or software checking this flag and thus relying on the overflow
flag would not work (properly).
Change-Id: Id2e5d69b5515c21e6ce922dab2cb88b494c65ebe
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57934
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Add support for SD card reader GL9750 and RTS5232S
BUG=b:203014989
TEST=FW_NAME=taeko emerge-brya coreboot
Signed-off-by: Joey Peng <joey.peng@lcfc.corp-partner.google.com>
Change-Id: I4353a094e2035ce94b5dd1a737e7e7009ad0614e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58318
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Follow the spec to correct the WWAN poweron and powerdown sequences.
BUG=b:195625346
TEST=USE="project_primus emerge-brya coreboot" and verify it builds
without error.
Signed-off-by: Ariel Fang <ariel_fang@wistron.corp-partner.google.com>
Change-Id: I232d283a9d6093f5da64fcdce44e5cb640e3df0e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58319
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Support GL9763E as a eMMC boot disk
BRANCH=none
BUG=b:202192686
TEST=enable DRIVERS_GENESYSLOGIC_GL9763E and check eMMC on taeko.
Cq-Depend: chromium:3153210
Signed-off-by: Kevin.Chang <kevin.chang@lcfc.corp-partner.google.com>
Change-Id: I5db2b229ce1bbea54efe15f5288f13f8d4656899
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58297
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: YH Lin <yueherngl@google.com>
|
|
The definition of those bits changed between Picasso and Renoir/Cezanne
so add a comment where those bit definitions are used as well.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: If1cf4b06fc35f94cbd482f2869fcc64739e7d272
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58345
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
The writes were originally added due to being part of the initialization
sequence in the reference code, but coreboot already has those registers
cleared by the time we reach this part of the code, so we can drop these
redundant writes.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I43344460e5355664841d77daf1df3fd386e047e9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58341
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
Move the actual implementation of configure_espi_with_mb_hook out of the
header file and into the espi_util.c file.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I1106e69a52bf329a41e8e12fd09db846310b102a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58340
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
If a system doesn't use eSPI or has the eSPI interface already
configured in verstage on PSP, not calling configure_espi_with_mb_hook
from fch_pre_init makes it a bit more obvious that the eSPI interface
initialization will be skipped.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ia77b83d56a5dab1bac6cfbbd92d33aa60a9e8b89
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58339
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
Rename configure_espi to configure_espi_with_mb_hook to clarify that
this function will call into the mb_set_up_early_espi function in the
mainboard-specific code if it exists.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I5d0f099288b0100242629c736dd69a8add977b5b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58338
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
Now that the I2C[ABCD]_BASE_ADDRESS defines aren't macros that calculate
the MMIO addresses any more, those defines can also be used in the ACPI
code.
TEST=Timeless build results in identical image for Google/Treeya.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I7de2f83dc2f8061d8f1735caf10314bcddb2d3fa
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58337
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
The I2C_BUS_ADDRESS(x) macro isn't used to iterate over the I2C
controller base addresses, so drop this and use the fixed MMIO address
for the I2C[ABCD]_BASE_ADDRESS defines instead which also allows using
those defines in the ACPI code.
TEST=Timeless build results in identical image for Google/Treeya.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Idd7484a0322dc5167cbb7fdcd9a2583f0dbed50e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58336
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
I2C_BASE_ADDRESS is the beginning of the MMIO space that contains the
I2C controllers MMIO. I2C[ABCD]_BASE_ADDRESS are the base addresses of
the 4 I2C controllers, so use I2CA_BASE_ADDRESS instead here.
TEST=Timeless build results in identical image for Google/Treeya.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ie8d6a438f76cd33929f5070f9ec6b2f280f471a0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58335
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
Before this patch the reservation of the MMIO region of the I2C
controllers was done in the LPC controller PCI device despite the I2C
controllers already being devices in the devicetree. This patch
implements this functionality as read_resources function of the I2C
device instead. This will only reserve the memory when the I2C devices
are enabled in devicetree which is a change from the previous behavior.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I67c853df3be2f593ecfa113ae2f74e5df7cf74e0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58307
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This change splits CSE metadata structure (added to CBFS) into two
separate CBFS files (me_rw.hash and me_rw.version). Since `struct
cse_rw_metadata` is now used, it is dropped completely.
This change is being made in order to prepare for the upcoming changes
to stitch CSE binary at build time. Since the binary might not be
available pre-built, it complicates the order of operations for the
addition of CSE metadata structure and declaring hash and version as
CPPFLAGS_common. Instead rules can be enabled for individual CBFS file
targets for hash and version that ensure proper ordering as well.
BUG=b:184892226
TEST=Ensured that update works correctly on brya by forcing version
mismatch. In case of version match, no update is triggered.
Signed-off-by: Furquan Shaikh <furquan@google.com>
Change-Id: I7c9bb165e6a64415affcd0b3331628092195fa0d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58158
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Set POWER_CTL MSR bit 18 to enable Energy/Performance Bias control.
TEST=Boot and verify EPB is enabled in coreboot log:
cpu: energy policy set to 6
Change-Id: Ibd1db77b5b63cb6e2b0ad9d2f79caa2f3b576ead
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58221
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
The SHRM region needs to be 4 byte aligned, which make enabling
compression slightly more complicated. We need to map it to cached
memory before loading it and flushing to memory (in aligned chunks)
then remapping the address space back to device memory before
beginning execution of the SHRM region.
Also, did some cleanup in this file based on comments in CB:49392.
BUG=b:182963902
BRANCH=None
TEST=Make sure we can still boot to kernel on herobrine
Change-Id: Iaad8a8a02abe40bd01766d94ef0b61aac7671936
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58191
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
Implement the read_resources function for the UART devices so that the
resource allocator knows about their fixed MMIO resources when enabled.
TEST=UART still works on Mandolin.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I4ffddee3f5f4281aca98ddfcefa639dfb7a38dae
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58306
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
Set PKG_CST_CONFIG_CONTROL MSR bit 15 to make bits 15:0 read-only.
Change-Id: Ieb740aa94255cb3c23a56495c4b645d847637b7f
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58222
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
This reverts commit 6260bf712a836762b18d80082505e981e040f4bc.
Reason for revert: This CL did not handle Intel GPIO correctly. We need
to add GPIO_EC_IN_RW into early_gpio_table for platforms using Intel
SoC.
Signed-off-by: Hsuan Ting Chen <roccochen@chromium.org>
Change-Id: Iaeb1bf598047160f01e33ad0d9d004cad59e3f75
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57951
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Configure I2C high / low time in the device tree to ensure Touchpad
I2C CLK runs accurately between 380 kHz and 400 kHz.
Measured I2C frequency just as below after tuning:
Touch Pad CLK: 389.2 KHz
BUG=b:202787528
TEST=Build and check after tuning I2C clock is between 380 kHz and 400 kHz
Change-Id: I0f9d062fc611de0062a39849aee1174268391682
Signed-off-by: Ian Feng <ian_feng@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58238
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Henry Sun <henrysun@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
|
|
Add PIXA touchpad into devicetree for sasukette.
BUG=b:202796169
BRANCH=dedede
TEST=built sasukette firmware and verified touchpad function
Signed-off-by: Zhi Li <lizhi7@huaqin.corp-partner.google.com>
Change-Id: I5bc8353692a753ec9254ab02b4ff0481386624b2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58239
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Weimin Wu <wuweimin@huaqin.corp-partner.google.com>
Reviewed-by: Henry Sun <henrysun@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Since espi_util.c is also built in the case of verstage on PSP, we can
just add it to all stages.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I65e07c356aac73c5de2d9ce5582434872a223c19
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58312
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
The bits REMOTE_IRR and SEND_PENDING are documented as read-only,
and reserved bits should not be modified either.
Change-Id: I6bcb9eb990debe169340a0bfe662158b62a8f4dc
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55700
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
The bit LAPIC_SPIV_ENABLE returns 0 after reset even though
LAPIC has not been temporarily disabled.
Change-Id: Id261bc68fe9d1b1b0e5a3ef599a8f33a686d283b
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55699
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Only the enable_lapic() part is required while doing
SMP init. Also disable_lapic() must not be called if
we rely on LAPIC for timer source.
Change-Id: Ib5e37c1a0a91fa4e9542141aa74f1c1876fee94e
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55261
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
If the VGA BIOS file path for `VGA_BIOS_FILE` in a mainboard's Kconfig
does not exist in the coreboot tree (including submodules), drop it.
These files should be stored in the `site-local` subdirectory and the
paths specified for each board in `site-local/Kconfig`. For example:
config VGA_BIOS_FILE
default "site-local/x200_vbios.bin" if BOARD_LENOVO_X200
Note that this is just an example. There are better ways to structure
one's `site-local` subfolder. Using the `CONFIG_MAINBOARD_DIR` option
would be one of them, though variants may still need special handling.
Also, update autoport to not generate `VGA_BIOS_FILE` defaults.
Change-Id: I1b5dfba035a42d7943f270f95fb7d32b285584d2
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51340
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
|
|
If available, use data from MEMINFO CBMEM table and saved handles
from type 17/19 tables to generate type 20 (Memory Device Mapped
Address) SMBIOS table.
Windows 10/11 and some other OSes use this table to report the total
memory available on a given device.
Change-Id: I2574d6209d973a8e7f112eb3ef61f5d26986e47b
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58271
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
microcode_file could be NULL and passed to get_microcode_size,
this was detected by klocwork scan.
Signed-off-by: Selma Bensaid <selma.bensaid@intel.com>
Change-Id: Ibb3d49ab18d8c26bbf5d6bf6bdf1bf91137f5736
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58233
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
There's no need to mask out bit 11, as it is unconditionally set. For
some reason, this changes the resulting coreboot image. Also simplify
another PCI operation with a redundant AND-mask.
Change-Id: I5492acd5f9c61db83a07ce7c1f6b887768c3eadf
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57499
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
variant_has_pcie_wwan helper returns true if gpp_bridge_2 PCIe engine is
enabled. On some variants, this engine is used by storage controllers.
Fix it by adding a weak override that returns no PCIe WWAN by default.
BUG=None
TEST=Build and boot to OS in Guybrush. Ensure that PCIe WWAN is
enumerated on boards where it is stuffed.
Change-Id: I07b9dd8fc5c8c3e1557f9268c1176d4a3cade1af
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58311
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
Scout only uses I2C 1, 2, and 3 in DVT units. This removes extraneous
I2C configuration copied from Puff.
BUG=b:202195805
TEST=Boot scout, verify no more errors due to missing I2C devices
Change-Id: Ide70a53e83b3e14540873062e3bef24d1134d2e1
Signed-off-by: Matt Ziegelbaum <ziegs@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58236
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
|
|
S3 is not currently functional on Guybrush. Remove support from ACPI.
BUG=b:202401767 b:181766974
TEST=Boot Guybrush
Confirm 'deep' is not in /sys/power/mem_sleep
Confirm S0ix suspend/resume still works
BRANCH=None
Change-Id: I9ed3e051f7f2e411670649ac2528a6f40229bdc6
Signed-off-by: Rob Barnes <robbarnes@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58282
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
`cse_fw_update()` is currently checking whether an update is required
by comparing versions once and then again comparing versions later in
`cse_is_downgrade_instance()` to determine if the update is an upgrade
or downgrade. Additionally, if CSE RW partition is corrupt (determined
based on `cse_is_rw_bp_sign_valid()`), `cse_is_downgrade_instance()`
ends up using the corrupted version information to determine if it is
a downgrade instance.
This change reorganizes the firmware update checks to return different
status values:
1. CSE_UPDATE_NOT_REQUIRED: No update required. Versions match.
2. CSE_UPDATE_UPGRADE: Update required and it is an upgrade.
3. CSE_UPDATE_DOWNGRADE: Update required and it is a
downgrade (requires data clear).
4. CSE_UPDATE_CORRUPTED: `cse_is_rw_bp_sign_valid()` failed and hence
requires data clear.
5. CSE_UPDATE_METADATA_ERROR: Unable to read CSE metadata from CBFS.
This change also prepares the file for follow up changes which
completely drop cse_rw_metadata structure.
BUG=b:184892226
Change-Id: Iabecab8e373e65a11ba7fe1bfc125467571a0588
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58157
Reviewed-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Currently WWAN_AUX_RST_L is in S5 domain and does not get asserted on
S0i3 entry. Based on the schematics, the pull-down on that signal leads
to 10 mW power leakage on S0i3 entry. Assert the signal on S0i3 entry to
achieve some power savings and de-assert it on S0i3 exit.
BUG=b:195748540
TEST=Build and boot to OS in Guybrush. Ensure that the signal gets
asserted on S0i3 entry and de-asserted on S0i3 exit. Trigger
suspend/resume cycles and ensure that the WWAN module is enumerated
after each cycle.
Change-Id: I43c8655ee5209779748e4365db973e094cb08aca
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58275
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add support to handle S0ix entry and exit notifications by adding the
corresponding _DSM functions. The function indices are chosen based on
the Modern Standby BIOS Implementation Guide 56358 Rev. 1.04. Inside
the notification functions perform any mainboard specific S0ix entry and
exit actions.
BUG=b:195748540
TEST=Build and boot to OS in Guybrush. Ensure that the notification
functions are invoked on S0ix entry and exit. Perform suspend/resume
cycles for multiple iterations.
Change-Id: I3014551f6e281d466628559453a0141a3dd6abad
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58274
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Correct the PCH serial IO settings, suitable for this mainboard.
Change-Id: I3c9915b2d52fbc6a15ac1e68c77bfb3983f7b1cd
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58296
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
Correct the USB settings, suitable for this mainboard.
Change-Id: I691d91d2a76e27b8efdc18eeae737a78e9ae38fa
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58295
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
Correct the remaining PCI devices, differing from the ehl1 mainboard.
Change-Id: I8112fa5ea86e879741061798530150701b759156
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58294
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
This mainboard has its own coreboot ready LED. The LED is switched
on via GPIO GPP_F20.
Change-Id: I3570d691e90d2cb6e11b856b876f0327da118522
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58293
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
Enable PCIe Clock power management and ASPM L1 substate by default. This
matches what Broadwell does.
Change-Id: Ic2bbcbc23d6bab0900d3e90ad8e2fbfa4aea3c16
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58281
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Enabling clock gating for CGPLL to lower power consumption in S3
and S0i3 states. See also: Cezanne PPR chapter 7, rev 3.03.
BUG=b:185273565
TEST=iotools mmio_read32 0xfed80e2c and 0e30 show clk gating
enabled and suspend_stress_test works.
Change-Id: I33cbdeec62e49db90b680da37e5028df03a9c015
Signed-off-by: Julian Schroeder <julianmarcusschroeder@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58279
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
Init overridetree based on the schematics.
Refer to brya0/overridetree.cb to update the settings of the devices
including DPTF, WIFI, NAU8825 and etc.
Refer to kano/overridetree.cb to update the SSD settings (pcie4_0).
TODO: DPTF and USB positions will be further updated later.
BUG=none
TEST=Build Pass
Signed-off-by: Alan Huang <alan-huang@quanta.corp-partner.google.com>
Change-Id: I30d26a47fe93736c63b578c9180b148ef73e8b9f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58165
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
HPD event may not be ready when configuring TCSS mux for DP,
check if any DP device is connected and wait for HPD ready before
TCSS configuration. Remove unnecessary dependency on mainboard
functions, use generic interface which provides USB-C mux
operations.
BUG=b:192947843
TEST=select ENABLE_TCSS_DISPLAY_DETECTION in Kconfig.name for
Brya. Build coreboot and update your Brya. Boot Brya with USB-C
display connected, you should find `HPD ready after %lu ms` and
`Port C%zd is configured to DP mode!` in coreboot log. Display
should show screen in developer mode or recovery mode.
Signed-off-by: Derek Huang <derek.huang@intel.corp-partner.google.com>
Change-Id: Ia7e6dd952d3183ecb76de6d4887ee573ef89bb50
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57139
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Currently override speed config is applied only for non EM100 cases.
For EM100 case, override speed board version defaults to 0 leading to
"comparison of unsigned expression >= 0 is always true" error. Fix this
error by defining the override speed config for both EM100 and non-EM100
use-cases.
BUG=None
TEST=Build Guybrush for both EM100 and non-EM100 cases.
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Change-Id: Id8ee7b01c69c4555d6e6a7b0d5f095ea3aaf3405
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58309
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Rob Barnes <robbarnes@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
P_BLK is legacy and superseded by ACPI _CST. Also, the implementation
for most platforms in soc/intel is broken. Thus, drop it.
For APL the IO redirection is kept since it's used as replacement for
the broken MWAIT instructions.
Change-Id: I489aa7886dd9a4c1e6c12542bc2a1feba245ec36
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58096
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
The HDAU stub device enables HDMI audio under MacOS.
Change-Id: Ifa2155512dd909a4e4a753f6475541e9410dfe91
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58272
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
No need for dynamic config (and the additional RAM training time)
on a Chromebox; always use high power/high performance mode.
Change-Id: I0295bac619af45a0d82da2bf39985c8bdcb77d5e
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58231
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
No need for dynamic config (and the additional RAM training time)
on a Chromebox; always use high power/high performance mode.
Change-Id: I8ad773d1c616b746235ec67b98b83c5910464140
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58230
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Add support to override SPI fast speeds based on board version from both
bootblock and verstage. Overrides apply for Guybrush only and SPI speed
is overridden from 66 MHz to 100 MHz starting board version 4. This will
help to improve the boot time on board version by ~60 ms and still allow
the old boards to boot with 66 MHz.
BUG=b:199779306
TEST=Build and boot to OS in Guybrush. Perform S5->S0, G3->S0, warm
reset and suspend/resume cycles for 50 iterations each.
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Change-Id: I5bf03ab8772f27aca346589e9c5662caf014d0d2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58117
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
Add support to override SPI ROM fast speed based on board version. This
will allow boards to start at lower speeds during bringup and then
switch to higher speeds after assessing the signal integrity. Also
implement a default no-op override.
BUG=None
TEST=Build and boot to OS in Guybrush. Perform S5->S0, G3->S0, warm
reset and suspend/resume cycles for 50 iterations each.
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Change-Id: Ia8ff3b3bdb53fee142527ae63aa7785945909304
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58116
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
Currently all SPI speed configurations are done through EFS at build
time. There is a need to apply SPI speed overrides at run-time - eg.
based on board version after assessing the signal integrity. This
override configuration can be carried out by PSP verstage and bootblock.
Export the APIs to set and read SPI speeds from both PSP verstage and
bootblock.
BUG=None
TEST=Build and boot to OS in guybrush. Perform S5->S0, G3->S0, warm
reset and suspend/resume cycles for 50 iterations each.
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Change-Id: I281531e506b56173471b918c746f58d1ad97162c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58115
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
eSPI is setup in two different locations in bootblock depending on early
port80 routing configuration. Also eSPI is setup in PSP, if verified
boot starts before bootblock. Consolidate all the scenarios by
initializating eSPI very early in fch_pre_init if verified boot starts
after bootblock and eSPI is enabled.
BUG=None
TEST=Build and boot to OS in Guybrush. Perform S5->S0, G3->S0, warm
reset and suspend/resume cycles for 50 iterations each.
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Change-Id: Icfeba17dae0a964c9ca73686e29c18d965589934
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58114
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
Since the GPIO mux/control MMIO regions are within the ACPIMMIO region,
we need to call enable_acpimmio_decode_pm04 here first so that accessing
the GPIO registers will work.
BUG=None
TEST=Build and boot to OS in Guybrush.
Change-Id: I4bc076261c72cf999a5f2464b74cff6bf694d473
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57782
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
update fw_config for nipperkin
BUG=b:196909635
BRANCH=guybrush
TEST=emerge-guybrush coreboot chromeos-bootimage
Signed-off-by: Kevin Chiu <kevin.chiu@quantatw.com>
Change-Id: Icd2c5509450e70aed158f146179f3a7fa24b547a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58161
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Bhanu Prakash Maiya <bhanumaiya@google.com>
Reviewed-by: Rob Barnes <robbarnes@google.com>
|
|
Tracker is a debugging tool, include AP/INFRA/PERI tracker.
When bus timeout occurs, the system reboots and latches some
values which could be used for debug.
Signed-off-by: Zhenguo Li <ot_zhenguo.li@mediatek.corp-partner.google.com>
Change-Id: I82f8e6e5f8ccb7f8246cae45a01a3ddd5f2966f2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58244
Reviewed-by: Rex-BC Chen <rex-bc.chen@mediatek.corp-partner.google.com>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Tracker is a debugging tool, include AP/INFRA/PERI tracker.
When bus timeout occurs, the system reboots and latches some
values which could be used for debug.
Signed-off-by: Zhenguo Li <ot_zhenguo.li@mediatek.corp-partner.google.com>
Change-Id: If457f4a096cd63038bf6b40552aa3caaba33d5fd
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58243
Reviewed-by: Rex-BC Chen <rex-bc.chen@mediatek.corp-partner.google.com>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
There is the wrong register offset printed in the debug log when the
data register is written:
'lpc_tpm: Write reg 0x18 with 0xnn' should be
'lpc_tpm: Write reg 0x24 with 0xnn' for data FIFO access.
This can be confusing when searching for issues with the help of the
TPM debug messages since the code itself is correct. Fix this error.
Change-Id: Ic28ee5a07146e804574b887ea05c62e7e88e9078
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58155
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Some poppy variants did not select a system type, which led to the
default desktop type being set. Select the best fit enclosure type
for each variant.
Alphabetize the variant-specific options for improved readability.
Change-Id: I7c23f8fa3ae1de67f7a68b8a4e9ec16c4e8044df
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58229
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Make use of the newly introduced ACPI macros for CPPC table generation
that currently exists of a bunch of confusing assignments of structs
that only get partially filled.
Test: dumped SSDT before and after do not differ.
Change-Id: I844d191b1134b98e409240ede71e2751e51e2159
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57888
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Lance Zhao
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Since the DRAM population is fixed to both channels on all mc_ehl boards
there is no need to have this 'half_populated' variable at all.
Simply use a fixed 'false' in the call of 'memcfg_init()' and delete
this variable here.
Change-Id: I783c17e6d92322a8b0c094cce803108e718011fa
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58177
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
|
|
The preferred location for the SPD data on mc_ehl based boards is the
HW-Info data structure. Inside this structure there is a field of 128
bytes available for the SPD data. So in order to use it construct a
buffer in memory which is 256 bytes long (as FSP requests minimum 256
bytes for the SPD data) and where the upper 128 bytes are taken from
HW-Info holding the needed timing parameters for LPDDR4.
If there is a case where HW-Info is not accessible or where the
contained SPD data is not valid (by checking the CRC in HW-Info SPD)
fall back to fixed SPD data set in CBFS.
Change-Id: I2b6a1bde0306ba84f5214b876eaf76ca12d8f058
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58176
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
|
|
Add supported memory parts in the mem_parts_used.txt and generate the
SPD ID for the memory parts. The memory parts being added are:
1. Samsung K4U6E3S4AB-MGCL
BUG=b:202480992
TEST=emerge-dedede coreboot
Signed-off-by: Zhi Li <lizhi7@huaqin.corp-partner.google.com>
Change-Id: I811f32defd50a940a09f238d38c962d2caf42855
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58196
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Weimin Wu <wuweimin@huaqin.corp-partner.google.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
|
|
For 1 bit long bit fields an unsigned type should be used. In this case
uint32_t is used instead of a generic unsigned int for both consistency
reasons with the rest of the file and to clarify that the bits will be
packed into a 32 bit memory location.
TEST=Resulting image of a timeless build for google/guybrush results in
identical binary.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ic630d1709174d90336746bc37da504437c12643c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58224
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
Replace the dt option `PmTimerDisabled` with use of the Kconfig option
`USE_PM_ACPI_TIMER` for enabling/disabling the PM Timer.
A default value representing the prior devicetree value was added to the
boards system76/{lemp10,galp5,darp7}, so this change will not alter
behaviour.
Change-Id: If1811c6b98847b22272acfa35ca44f4fbca68947
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58016
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lance Zhao
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Tim Crawford <tcrawford@system76.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Set PKG_CST_CONFIG_CONTROL MSR bit 15 to make bits 15:0 read-only.
Change-Id: Ia196906d3c2636742ae90160a224354e8df7863a
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58220
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Add a space before the `*/` C-style comment ending.
Change-Id: Ic8928286c8237808b9e380e4393078792589615d
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58219
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
|
|
Update MAX98360 ACPI HID from "MX98357A" to "MX98360A"
BUG=b:198716348
TEST=Build nipperkin, codec is functional with new machine driver.
Cq-Depend: chromium:3195465
Signed-off-by: Patrick Huang <patrick.huang@amd.corp-partner.google.com>
Change-Id: I8a1155848856db0cc4f42cfee0d914f8d1186b34
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58106
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
coreboot normally owns PCIe resets for all Cezanne based systems.
However during S0i3 resume coreboot cannot intervene for S0 GPIOs
(S5 carry over fine) so we needed an alternate way to de-assert
this reset on guybrush. This change feeds in the given S0 reset
GPIO (69 in this case) so that SMU may de-assert this reset on
S0i3 resume.
BUG=b:199780346
TEST=With latest FSP verify SD device trains each of 10 cycles
Cq-Depend: chrome-internal:4157948
Change-Id: Ieee31651db30147fda84ee1aa31df7cb1c206356
Signed-off-by: Matt Papageorge <matthewpapa07@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58198
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Update UPD to include option for FSP to de-assert PCIe reset GPIOs as
specified in the DXIO descriptors. This change requires FSP version
1.0.4 revision 2 otherwise setting this value does affect any FSP
behavior.
BUG=b:199780346
TEST=Verify toggling this value is reflected in FSP
Cq-Depend: chrome-internal:4170351
Change-Id: I0dee05fb0a650f026c2f09581117fa7fb5f6a90a
Signed-off-by: Matt Papageorge <matthewpapa07@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58197
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
bootblock_mainboard_early_init gets called before console_init.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ia5a1da336e8dfc451177a5319a656c407c9fef7d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58077
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
Document what setting the PM_ACPI_S5_LPC_PIN_MODE and
PM_ACPI_S5_LPC_PIN_MODE_SEL bits causes. The corresponding code will
eventually be factored out and moved to the Cezanne SoC code.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I10e3eee5cfc1c5ba2c88b8b7e83e96e481f787e1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58070
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
Since the LPC_LDRQ0_PD_EN gets set right after it got cleared, we can
remove the clearing of that bit. This is split off from the previous
patch to be able to use timeless build to verify that the previous patch
didn't change any behavior.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ieb300e7c7ce7e74c32ebdade0360ee4bd499b11a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58069
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
It's hard to understand what this code is doing because it uses hard
coded values, so use the register and bit defines instead.
BUG=none
TEST=Timeless build for guybrush results in identical binary.
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I2d74ed3b9b4984ab1e2a22c50375baf9c9589df0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57051
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Register and bit definitions are from the Cezanne PPR #56569 Rev 3.03.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ib109efe679560604ff8209b4177611eb2aa9ebdf
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58068
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
The definitions of bit 9 and 10 somehow got swapped between Picasso and
Renoir/Cezanne, so put those in the Cezanne-specific header file. The
reference code writes the same values to the raw bits in both, so we
probably would still get away with putting this into the common header,
but it's better to keep the defines consistent with the documentation in
all cases.
Register and bit definitions are from the Cezanne PPR #56569 Rev 3.03
and cross-checked to be compatible with the Picasso PPR #55570 Rev 3.16.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I3a033d63eeb06eed6783e4c3797ad8dea490db8d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55294
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
Fizz's USB ACPI code is intended to allow the OS to control port
charging power, but since Fizz's ports are dumb (vs smart), it
controls power to the port itself. The end result is that active
ports become disabled when rebooting from Windows (10/11), and
power is not restored until the device is powered down (a warm
reboot is not sufficient).
Subsequent Chromebox models (eg, Puff-based variants) don't bother
with EC-controlled USB port power, so just drop it since it's
problematic and provides no benefit.
Test: boot Windows 10/11, reboot, observe active USB ports still
functional (eg, USB KB still works)
Change-Id: I2c13d49b3ce8de8b0a38512db3c57d0c8ecbf0ad
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58185
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
|
|
Populate a memory_info struct with PEI and SPD data, in order to inject
the CBMEM_INFO table necessary to populate a type17 SMBIOS table.
On Broadwell, this is done by the MRC binary, but the older Sandy Bridge
MRC binary doesn't populate the pei_data struct with all the info
needed, so we have to pull it from the SPD.
Some values are hardcoded based on platform specifications.
Change-Id: I15e00a01121150b778cfa684b9147d0cac97beb8
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58188
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Test: build/boot Purism Librem 13v1, verify brightness controls
work under Windows 10/11 with Tianocore payload.
Change-Id: I27d04655adcd4a5dd42b025cfccb508cfd7aaeae
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58187
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
|
|
Caroline uses a Wacom digitizer, so adjust the ACPI HID
so that the proper drivers attach under Windows/Linux.
Change-Id: I732b09001dc41a91a32a5f9260abdab435b28b8a
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58186
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
|
|
Before attempting another commit 6260bf71 (vboot_logic: Set
VB2_CONTEXT_EC_TRUSTED in verstage_main), ensure that guybrush builds
chromeos.c in verstage to call get_ec_is_trusted() in vboot
verstage_main().
Signed-off-by: Hsuan Ting Chen <roccochen@chromium.org>
Change-Id: Ic22519fdde1b18f6ce0237022dee02ca37181a74
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58193
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
|
|
Before attempting another commit 6260bf71 (vboot_logic: Set
VB2_CONTEXT_EC_TRUSTED in verstage_main), ensure that guybrush programs
GPIO_EC_IN_RW (GPIO_91) as an early GPIO so that it can be read from in
verstage.
Signed-off-by: Hsuan Ting Chen <roccochen@chromium.org>
Change-Id: Ia6dcb225bbca89f3a873aad75a7d67625cdd3742
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58192
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
ALC5682-VD/ALC5682I-VS load different kernel driver by different hid
name. Update hid name depending on the AUDIO_CODEC_SOURCE field of
fw_config. Define FW_CONFIG bits 41 - 43 (SSFC bits 9 - 11)
for codec selection.
ALC5682-VD: _HID = "10EC5682"
ALC5682I-VS: _HID = "RTL5682"
BUG=b:198713670
TEST=ALC5682-VD/ALC5682I-VS audio codec can work
Signed-off-by: FrankChu <frank_chu@pegatron.corp-partner.google.com>
Change-Id: Iaba136a836b89f42411474ae733380e345cce687
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58162
Reviewed-by: Henry Sun <henrysun@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
1. Fix PCIe slot capabilities not being really read from an IIO root
port device. The Hot-Plug capability of IIO root port cannot be
enabled due to FSP limitation (v2.1-0.2.2.0), but the code should
reflect the true capabilities by reading the root port device's CSR.
2. Initialize the characteristics flags to 0 in the for-loop to fix the
issue of the flags values persists to the next iterations.
Tested=On OCP Delta Lake, dmidecode -t 9 shows the expected results.
For example without the fix it shows 'Hot-plug devices are supported'
but in fact it's not:
System Slot Information
Designation: SSD1_M2_Data_Drive
Type: x4 PCI Express 3 x4
Current Usage: Available
Length: Short
ID: 1
Characteristics:
3.3 V is provided
PME signal is supported
Hot-plug devices are supported
Bus Address: 0000:00:1d.0
With the fix it shows the correct result:
Handle 0x0016, DMI type 9, 19 bytes
System Slot Information
Designation: SSD1_M2_Data_Drive
Type: x4 PCI Express 3 x4
Current Usage: Available
Length: Short
ID: 1
Characteristics:
3.3 V is provided
PME signal is supported
Bus Address: 0000:00:1d.0
Change-Id: Iea437cdf3da5410b6b7a749a1be970f0948d92d9
Signed-off-by: Johnny Lin <johnny_lin@wiwynn.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58100
Reviewed-by: Johnny Lin <Johnny_Lin@wiwynn.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Jonathan Zhang <jonzhang@fb.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
On this mainboard there is a legacy PCI device, which is connected to
the PCIe root port via a PCIe-2-PCI bridge. This device only supports
legacy interrupt routing. For this reason, we have to adjust the PIR8
register (0x3150) which is responsible for PCIe device 25h. The bridge
is connected to PCIe root port 7.
The following routing is required:
INTA#->PIRQC#, INTB#->PIRQD#, INTC#->PIRQA#, INTD#-> PIRQB#
TEST:
- Boot into system software
Change-Id: Id6bb8d00458c4d1e3fefd01ac3848078355868d9
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58172
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
In upcoming patches, we need mainboard specific adjustments.
Change-Id: Icf9d829b19b2d26a39ad34be4658064083e9da6d
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58171
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
|
|
Enable LPC ComB on this mainboard.
TEST:
- Boot Linux and check with 'dmesg | grep tty'
Change-Id: I7ec58685a723c177df18144011934b206e6425d0
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58170
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
|
|
This mainboard uses an eSPI-to-LPC bridge for console output. For this
reason, the internal LPSS UART must be disabled.
Change-Id: I86777cf719def331f4d257ddd94e9a87125ebce8
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58169
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
|
|
Set the GPIOs according to the circuit diagram for this mainboard.
Change-Id: I19dc24a16ee9f533b45879bf60fb441e24018cc8
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58168
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
|
|
This mainboard has only SATA Port 1 available with no device sleep
feature.
Change-Id: I338833f2f9bcb407599cfc676ead0b8a9d7379bd
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58167
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
|
|
This mainboard has SD slot available and therefore it should be enabled.
Change-Id: I0c97e2dc589bf6b89713a473925e42a20278f457
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58166
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
|
|
This board has the RTC RX6110SA connected to the I2C2 instead of SMBus
as in mc_ehl1. Set the bus speed for I2C2 to 100 kHz, since this RTC
only supports the standard speed.
TEST:
- Console Log shows no errors for RX6110SA during I2C2 init
- Finalize device for I2C 00:32 shows correct date and time
Change-Id: I679c6397fa0d213a25eebaf8a9e0bda9941acd26
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58112
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
Since this variant uses different DDR4 devices compared to mc_ehl1 in a
memory down configuration, the SPD data file must be adapted.
In a first configuration we use Micron MT53D512M32D2NP modules.
Following values were adjusted according to this board characteristic
and with help of Serial Presence Detect (SPD) for LPDDR3 and LPDDR4
SDRAM Modules JEDEC Spec and the Specification for this Micron modules
itself:
- SPD Byte 4 - only 4Gb density instead of 8Gb for mc_ehl1
- SPD Byte 5 - different Row and Column Address Bits
- SPD Byte 29/30 - 4Gb LPDDR4 needs 130ns tRFCab
- SPD Byte 31/32 - 4Gb LPDDR4 needs 60ns tRFCpb
Change-Id: Icb25f418952f0c96117140863d0d9c897d814ac5
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58111
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
Add Synaptics touchpad device support in devicetree.
BUG=b:201043984
BRANCH=dedede
TEST=Touchpad device function is OK
Change-Id: Ifb240d7113e401de827384697fc752a76fbf7ac7
Signed-off-by: Alex1 Kao <alex1_kao@pegatron.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57921
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kirk Wang <kirk_wang@pegatron.corp-partner.google.com>
Reviewed-by: Shou-Chieh Hsu <shouchieh@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Return the package with a value for the dptf user space service.
This is required in write tpch method for pch device under dptf
driver.
BUG=b:198582766
BRANCH=None
TEST=Build FW and test on brya0 board
Change-Id: I64e1bb04a6115c7f93c84a5d6644101ac1d3d8ba
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58174
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
The PCI-SIG engineering change requirement provides the ACPI additions
for firmware latency optimization. This change adds additional ACPI DSM
function with both of FW_RESET_TIME and FW_D3HOT_TO_D0_TIME to the
USB4/TBT topology. The OS is informed to reduce latency for upstream
ports while connecting USB4/TBT devices.
BUG=b:199757442
TEST=It was validated that the first connected device waits only 50ms
instead of 100ms and all functions work on Voxel board.
Signed-off-by: John Zhao <john.zhao@intel.com>
Change-Id: I5a19118b75ed0a78b7436f2f90295c03928300d7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57625
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Add various methods support for pch device under dptf driver.
This provides support of different control knobs for FIVR.
BUG=b:198582766
BRANCH=None
TEST=Build FW and test on brya0 board
Change-Id: I2d40fff98cb4eb9144d55fd5383d9946e4cb0558
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57925
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
