Age | Commit message (Collapse) | Author |
|
parts.
This should help to reduce the code duplication for Rudolf's K8/VIA SMM
implementation...
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Joseph Smith <joe@settoplinux.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3870 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
SATA port status kept returning 0x1: BAR5+po+28h
1h = Device presence detected but Phy communication not established
This patch adds logic to force 1.5g if the drive fails to communicate at 3.0g.
Signed-off-by: Dan Lykowski <lykowdk@gmail.com>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3864 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
is no longer 0xA0 or 0xB0. It simply assumes that will never happen.
My 500 GB Seagate Barracuda ST3500820AS triggers that corner case on the
first init after poweron.
The current code hangs forever with my drive. Fix this by rerunning the
init sequence after SATA_BAR0+6 is no longer 0xA0 or 0xB0.
Add support for SATA port 2-4 (Primary Slave, Secondary Master,
Secondary Slave).
If only the 2nd SATA port is connected and the hardware acts strangely
(contrary to documentation), it will print the error message below and
continue anyway. The official AMD asm code behaves the same way.
SATA port 0 status = 0
No Primary Master SATA drive on Slot0
SATA port 1 status = 23
0x6=7f, 0x7=7f
drive no longer selected after 0 ms, retrying init
[8 repetitions]
0x6=7f, 0x7=7f
drive no longer selected after 0 ms, retrying init
Primary Slave device is not ready after 10 tries
Activate and improve debug messages for SPEW log level.
Fix some comments.
New log messages look like this:
PCI: 00:12.0 init
sata_bar0=3020
sata_bar1=3060
sata_bar2=3030
sata_bar3=3070
sata_bar4=3000
sata_bar5=fc309000
SATA port 0 status = 23
0x6=a0, 0x7=80
drive detection not yet completed, waiting...
0x6=a0, 0x7=80
drive detection not yet completed, waiting...
[... 281 repetitions ...]
0x6=0, 0x7=50
drive no longer selected after 2820 ms, retrying init
drive detection done after 0 ms
Primary Master device is ready after 2 tries
SATA port 1 status = 23
drive detection done after 0 ms
Primary Slave device is ready after 1 tries
SATA port 2 status = 0
No Secondary Master SATA drive on Slot2
SATA port 3 status = 0
No Secondary Slave SATA drive on Slot3
With this patch, my Asus M2A-VM boots into Linux without problems.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Zheng Bao <zheng.bao@amd.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3845 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
The RS690 chipset has a problem where it will not work with 1 GHz HT
speed unless NB_CFG_Q_F1000_800 bit 0 is set.
Tested, works on my Asus M2A-VM with an 1 GHz HT capable processor.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Bao, Zheng says:
As a matter of fact, both 600Mhz and 1Ghz have their own specific
setting.
This patch has been tested on dbm690t which HT link works on 800Mhz.
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3839 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
the SB600 code.
Signed-off-by: Maggie Li <Maggie.li@amd.com>
Reviewed-by: Zheng bao <Zheng.bao@amd.com>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3837 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Fix imlicit mdelay in src/southbridge/nvidia/mcp55/mcp55_nic.c
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Myles Watson <mylesgw@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3831 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Corey Osgood <corey.osgood@gmail.com>
Acked-by: Myles Watson <mylesgw@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3822 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Corey Osgood <corey.osgood@gmail.com>
Acked-by: Myles Watson <mylesgw@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3819 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
except get_nodes.
Signed-off-by: Myles Watson <mylesgw@gmail.com>
Acked-by: Marc Jones <marcj303@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3818 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
The device ID of 690G is 0x791E, while the ID of 690M and 690T is 0x791F
This fixes booting on 690G.
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3816 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
mainboard specific code. (And add a hook to allow other mainboards do
a similar thing if required)
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Ronald G Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3812 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
document verification against the data sheets.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Maggie Li <maggie.li@amd.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3811 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
0xe4 and 0xe5 registers. I'm suspecting that the documentation may be wrong.
Furthermore this fix for powernow may not work on CPUs hit by errata #181.
Workaround should be implemented. The powernow may not work on pre-A2 revisions
of VT8237S silicon, revision reg is unknown.
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3795 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Joe Bao <zheng.bao@amd.com>
Reviewed-by: Maggie Li <maggie.li@amd.com>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
Acked-by: Marc Jones <marcj303@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3786 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Joe Bao <zheng.bao@amd.com>
Reviewed-by: Maggie Li <maggie.li@amd.com>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
Acked-by: Marc Jones <marcj303@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3785 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Myles Watson <mylesgw@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3752 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Also, fix BIOS_CNTL, which is 0xdc on ICH7.
Build-tested with kontron/986lcd-m.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3733 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
ICH7 southbridge (but it might work with ICH4/ICH5 or so).
The ICH7 needs a different init code. Drop the non-working code for now.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3732 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
to only a set of reasonably similar ones, namely (for now) ICH0* - ICH6*,
and C-ICH.
All later ICH* southbridges (ICH7-ICH10) are _very_ different and were surely
not working with this driver anyway (and there's no chance to support
them reasonably with this driver without ending up in #ifdef hell).
ICH7 now has an extra driver in svn, whether ICH8-ICH10 are similar
enough to be supported by that ICH7 driver remains to be seen.
This patch was informally acked by Stefan Reinauer
<stepan@coresystems.de> on IRC.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3718 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Build-tested on kontron_986lcd_m.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3715 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Build-tested with the kontron/986lcd-m target.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3705 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
This includes an early SMI handler.
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3701 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Also, use more readable #defines instead of hardcoded config ports for
PM/PM2 related functions, and simplify them a bit.
Build-tested with the AMD dbm690t target.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Marc Jones <marc.jones@amd.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3680 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Jordan Crouse <jordan.crouse@amd.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3678 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
build. As far as I know, no C7 boards currently in the tree use SPI
flash.
Signed-off-by: Corey Osgood <corey.osgood@gmail.com>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3665 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
called from one target and that target is compiled with GCC, make the
function dependent on GCC.
ROMCC also chokes on the ULL suffix for integer constants. Change the
affected ones to UL for ROMCC compiled code.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3664 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
is also visible to ROMCC and ROMCC doesn't understand that.
The fix is to use __attribute__((packed)) only for gcc compiled code.
This has been unfixed for too long. There are more problems remaining,
but at least this one is solvable easily.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3660 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Build-tested with the AMD dbm690t board.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Marc Jones <marc.jones@amd.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3655 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Corey Osgood <corey.osgood@gmail.com>
Acked-by: Corey Osgood <corey.osgood@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3652 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3651 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
cleanup. (trivial)
Signed-off-by: Marc Jones <marcj.jones@amd.com>
Acked-by: Marc Jones <marcj.jones@amd.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3643 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
We shouldn't assume the presence of a working HDA codec, so put in
a reasonable timeout of 50usecs (timeout value borrowed from the kernel).
This makes SimNow work, since apparently though the codec is
present in Simnow, it is non functional.
Signed-off-by: Jordan Crouse <jordan.crouse@amd.com>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3640 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
got checked into v2. This should get us back to where we were. (trivial)
Signed-off-by: Marc Jones <marc.jones@amd.com>
Acked-by: Marc Jones <marc.jones@amd.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3636 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3631 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
certainly won't build -- that comes later. I am hoping to get some
eyeballs on it for simple errors.
rs690 is next.
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3630 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
code to use it. That makes the code more readable and also less
error-prone.
Abuild tested.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3624 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Most of the functions in SB600 are enabled except power management.
Signed-off-by: Michael Xie <Michael.Xie@amd.com>
Reviewed-by: Marc Jones <marc.jones@amd.com>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3589 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
All the PCIe slots are enabled in this patch except power management.
Signed-off-by: Michael Xie <Michael.Xie@amd.com>
Reviewed-by: Marc Jones <marc.jones@amd.com>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3588 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
be the
D1F0 bridge without activated I/O and MEM resources, otherwise it will hang
whole PCI bus.
U-boot is also disabling the IO/MEM decode when sizing the BARs, dont know why
does we not.
Second small change just changes a bit which controls the PSTATECTL logic.
Third change deals with the integrated VGA, which needs to be enabled early,
so the VGA_EN is set along the bridges, and PCI K8 resource maps are set
correctly. Finally the CPU accessible framebuffer is now disabled as it is not
needed.
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3587 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Myles Watson <mylesgw@gmail.com>
Acked-by: Myles Watson <mylesgw@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3584 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
programming remains unchanged (tested
on mine desktop) except of reverting the small change introduced by Bari
(gpio/inta setup reg 0x5b). This should go for some board specific file. The
change would broke at least mine board. But seems to be needed for jakllsch.
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Bari Ari <bari@onelabs.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3567 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Ed Swierk <eswierk@arastra.com>
Acked-by: Ed Swierk <eswierk@arastra.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3563 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
All devices work, no irq storms. Enjoy.
Signed-off-by: Bari Ari <bari@onelabs.com>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3556 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
and renames some existing macros for clarity.
Signed-off-by: Ed Swierk <eswierk@arastra.com>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3536 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
integrated LPC, SMBus, USB and SATA devices of the Intel EP80579
Integrated Processor.
Signed-off-by: Ed Swierk <eswierk@arastra.com>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3535 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3451 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
patch uses byte pointer and the MMIO read and write functions.
Signed-off-by: Marc Jones <marc.jones@amd.com>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3421 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Bari Ari <bari@onelabs.com>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3369 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
allowing you to specify per-mainboard GPIO settings.
Signed-off-by: Ed Swierk <eswierk@arastra.com>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3290 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
doing a
pci_write_config8.
Signed-off-by: Marc Jones <marc.jones@amd.com>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3282 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
for both serial ports, making it challenging to use COM2 for the early
console.
Enable the traditional I/O ranges 0x3f8 for COM1 and 0x2f8 for COM2.
Signed-off-by: Ed Swierk <eswierk@arastra.com>
Acked-by: Joseph Smith <joe@settoplinux.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3276 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
secondary controller was ok). There were two problems: the master sata
controller was not being initialized, and the irqs for the secondary ports on
both controllers were not being set in the mptable.
Thanks for Jonathan Kollasch for all the help figuring out the IRQ problem.
While all ports work reliably under a recent kernel (2.6.24), sata is about
half as fast as under the proprietary bios, according to bonnie++. That still
needs fixing...
Signed-off-by: Ward Vandewege <ward@gnu.org>
Acked-by: Myles Watson <mylesgw@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3253 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
southbridges.
It also keeps the boot processes from rebooting through out the coreboot process.
Signed-off-by: Joseph Smith <joe@smittys.pointclark.net>
Acked-by: Corey Osgood <corey.osgood@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3218 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
"off" in Config.lb should cause the PCI device not to respond to
configuration requests.
Replace the existing code that I naively copied from esb6300 with
something that actually works on the 3100.
Signed-off-by: Ed Swierk <eswierk@arastra.com>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3209 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Joseph Smith <joe@smittys.pointclark.net>
Acked-by: Corey Osgood <corey.osgood@gmail.com>
Acked-by: Ed Swierk <eswierk@arastra.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3208 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Ed Swierk <eswierk@arastra.com>
Acked-by: Ed Swierk <eswierk@arastra.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3207 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
There are no boards that use the i82801DB (ICH4). The code does NOT work.
Signed-off-by: Joseph Smith <joe@smittys.pointclark.net>
Acked-by: Corey Osgood <corey.osgood@gmail.com>
Acked-by: Ed Swierk <eswierk@arastra.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3206 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
pci_locate_device() to locate the SMBus controller and LPC bridge
devices on the PCI bus. Since these devices are always located at a
fixed PCI bus:device:function, the code can be simplified by
hardcoding the devices.
Signed-off-by: Ed Swierk <eswierk@arastra.com>
Acked-by: Corey Osgood <corey.osgood@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3205 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
the system automatically unless software resets the timer
periodically. The extra reboot extends boot time by several seconds.
The attached patch adds a function to the Intel 3100 southbridge code
that halts the TCO timer, thus preventing this extra reboot, and calls
the function early in the boot process on the Mt. Arvon board.
It also fixes a bug in the LPC device initialization -- the ACPI BAR
enable flag is bit 7, not bit 4.
Signed-off-by: Ed Swierk <eswierk@arastra.com>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3198 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
You can see this by executing commands like this:
grep -r pci_assign_irqs coreboot/src/*
This basically AMD/LX based boards: pcengines/alix1c,
digitallogic/msm800sev, artecgroup/dbe61, amd/norwich, amd/db800.
Also for AMD/GX1 based boards need a patch
[http://www.pengutronix.de/software/ptxdist/temporary-src/references/geode-5530.patch]
for the right IRQ setup.
AMD/GX1 based boards is: advantech/pcm-5820, asi/mb_5blmp, axus/tc320,
bcom/winnet100, eaglelion/5bcm, iei/nova4899r, iei/juki-511p.
I have two ideas.
1. Delete duplicate code from AMD/LX based boards.
2. Add IRQ routing for AMD/GX1 boards in coreboot.
The pirq.patch for IRQ routing logically consist from of two parts:
First part of pirq.patch independent from type chipsets and assign IRQ for
ever PCI device. It part based on AMD/LX write_pirq_routing_table() function.
Second part of pirq.patch depends of type chipset and set PIRQx lines
in interrupt router. This part supports only CS5530/5536 interrupt routers.
IRQ routing functionality is included through PIRQ_ROUTE in Config.lb.
Tested on iei/juki-511p(cs5530a), iei/pcisa-lx(cs5536) and also on
TeleVideo TC7020, see
http://www.coreboot.org/pipermail/coreboot/2007-December/027973.html.
Signed-off-by: Nikolay Petukhov <nikolay.petukhov@gmail.com>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3196 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
The V-link setup and HT bridge is redone, because VT8237A has it in another
device. So far following combination of chipsets should now work:
K8T890CE + VT8237R
K8M890(CE) + VT8237R
VIA PC1 brige moved to NB code (vt8237r_bridge.c -> k8t890_bridge.c) and
notes about K8M890 support were added.
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3183 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
max width of the link and also it will take the frequency of K8 HT
already done coreboot (and checks if t can run on it).
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3169 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
comments. Ripping out the ehci/uhci_init() code doesn't seem to have
done any harm, and I got rid of a bunch of unused junk in
i3100_smbus.h
I left the *_set_subsystem() arguments unsigned, as that's how the
function is declared in include/device/pci.h.
Signed-off-by: Ed Swierk <eswierk@arastra.com>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3157 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
flashes such as SST49LF080A: 1024K x8 (8 Mbit)
Tested on my system, the flash is found and if I use coreboot in second half it
works too.
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3148 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
nVidia cards. The enable link should be enough, retrain is done there.
Tested on my system.
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3147 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
a compiler warning.
Signed-off-by: Ronald Hoogenboom <hoogenboom30@zonnet.nl>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3115 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Don't enable pin0 for ioapic of io-4.
1. apic error in kernel for MB with mcp55+io55
2. some pcie-cards could have pci bridge there, so need to put entries
for device under them in mptable.
Signed-off-by: Yinghai Lu <yinghailu@gmail.com>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3112 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Due to the automatic nature of this update, I am self-acking. It worked in
abuild.
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3053 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
code is changed.
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3052 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Check that the SMBus controller is found and stop on an error.
Clean up and add additional path through the 8111 reset functions.
Signed-off-by: Marc Jones <marc.jones@amd.com>
Reviewed-by: Jordan Crouse <jordan.crouse@amd.com>
Acked-by: Myles Watson <myles@pel.cs.byu.edu>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3015 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
- Implement ISA related support:
- Initialize the RTC
- Enable access to all BIOS regions (but _not_ write access to ROM)
- Enable ISA (not EIO) support
- Without the *_isa.c file, the Super I/O init is never performed
- Improve IDE support:
- Add config option to enable Ultra DMA/33 for each disk
- Add config option to enable legacy IDE port access
- Implement hard reset support
- Implement USB controller support
- Various code cleanups and improvements
The code partially supports southbridges other than the 82371EB (but
which are very similar), more complete support will follow.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2994 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2990 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
2. Southbridge PCIe slots are working correctly now.
3. Disable keyboard & mouse ports for GA-2761GXDK.
Signed-off-by: Morgan Tsai <my_tsai@sis.com>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2976 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
- Use 'static' where appropriate.
- Use 'const' where appropriate.
- Indentation fixes.
- Add comment wrt init code which is only valid for VT8237R.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2974 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
* Strip unnecessary driver modules.
Signed-off-by: Morgan Tsai <my_tsai@sis.com>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2971 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Upon incoming SMAF message from CPU (C3 or FID/VID change), the SB will
assert SLP# which is connected to LDTSTOP_L on K8 CPUs. Question is for how
long. Imho for 100us. Which is more than plenty (2us required) I will try
to justify this once I know what bios to set in SB.
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2965 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
it to 8X transfer rate (up to 1066 MB/s) similar code placed here would be
needed for VT8237A/S etc. Using VIA recommended values despite they are for
K8T890CF, this is K8T890CE (still dont know what is exactly different).
This patch enables the parity error reporting on V-Link, so it enables NMI
generation for the SERR# errors. The NMI may not be generated, maybe port
61h needs some tuning too.
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2958 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
i82801xx code for the following parts:
- AC97 audio/modem
- Onboard network interface cards (NICs)
- USB 1.1 controllers
- SMBus controllers
Some other parts are still missing and will be added later.
Use PCI ID #defines from pci_ids.h everywhere. Constify various structs.
Also, fix some random cosmetic issues in the code.
All of this is relatively trivial and tested by manually building
all boards which currently use the i82801xx code.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2951 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
ARRAY_SIZE() can be used on ROMCC-dependent systems. Also adds stdlib.h
to vt8237r_early_smbus.c, so it'll build on those systems.
Signed-off-by: Corey Osgood <corey.osgood@gmail.com>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2949 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
(ICH/ICH0 up to the ICH9 family) in preparation for further
code improvements for the i82801xx southbridge code.
Small fixes in the 6300ESB PCI IDs.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2947 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
* Remove dead code
* Remove unused variables
* Fix bug where array was one element too small
* Fix error value truncation, the old code never entered the error path
* Remove warnings
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2945 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2939 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
ICH5/ICH5R (more to follow) in preparation of further 82801xx improvements.
Use human-readable names for the PCI ID #defines.
Rename *_ISA to *_LPC as per datasheet.
The 82801DBM only has 3 (not 4) USB devices, looks like a copy-paste error.
The fixes in southbridge code are only to keep the build working for now,
any real improvements will only go into the 82801xx code in future.
This is abuild-tested so it shouldn't break anything.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2938 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
the Jetway J7F2 patch that should be coming soon, and also moves most
defines into vt8237r.h. I've changed some of the values from u32 to u8,
because that's all they should ever need to be. Also includes
doxygenized comments!
Signed-off-by: Corey Osgood <corey.osgood@gmail.com>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2937 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2933 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
No functional code changes.
Signed-off-by: Jordan Crouse <jordan.crouse@amd.com>
Acked-by: Jordan Crouse <jordan.crouse@amd.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2932 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
2. Rename sisnb.c to sis761.c
3. Delete many mis-definition for sis device in
src/include/device/pci_ids.h
4. Trim trailing spaces for all files
Signed-off-by: Morgan Tsai <my_tsai@sis.com>
Acked-by: Jordan Crouse <jordan.crouse@amd.com>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2931 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2925 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Joseph Smith <joe@smittys.pointclark.net>
Acked-by: Corey Osgood <corey.osgood@gmail.com>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2912 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: <corey.osgood@gmail.com>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2907 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
code. This is trivial, I did it for the other components before.
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2905 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
southbridge now:
From: Morgan Tsai <my_tsai@sis.com>
It supports SiS761GX / SiS966 chipset, only for AMD K8 platform so far.
Due to integrated VGA sharing system memory, some code in southbridge
folder have to init northbridge.
Copyright (C) 2007 Morgan Tsai <my_tsai@sis.com>
Copyright (C) 2007 Silicon Integrated Systems Corp. (SiS)
Change Log:
Newly support GIGABYTE GA-2761GXDK
CPU type: AMD AM2 socket
Northbridge: SiS 761GX
Southbridge: SiS 966
SuperIO: ITE8716F
Signed-off-by: Morgan Tsai <my_tsai@sis.com>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2902 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2893 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
rodata.pci_driver" warnings are coming from? We were packing those
structures into a read-only segment, but forgot to mark them const.
Despite its size, this is a fairly trivial patch created by a simple
search/replace
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2891 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2883 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Painting the splash graphic is now ifdef'ed.
Signed-off-by: Juergen Beisert <juergen127@kreuzholzen.de>
Acked-by: Peter Stuge <peter@stuge.se>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2836 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
to set up one of five screen resolutions (sorry no autodetection at runtime,
resolution is selected at buildtime) and displays a graphic in the right
bottom corner (splash screen).
Signed-off-by: Juergen Beisert <juergen127@kreuzholzen.de>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2827 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
i82801DB to reset. See this thread for more info:
http://article.gmane.org/gmane.linux.bios/26791
Signed-off-by: Joseph Smith <joe@smittys.pointclark.net>
Acked-by: Corey Osgood <corey.osgood@gmail.com>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2816 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
fixes the problems with PCI add-on cards not being detected or
initialized on MCP55-based systems (PCI bridge decoding change).
I have tested this on the MSI MS-7260 (K9N Neo) with a PCI VGA card,
which worked fine in any of the three PCI slots.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2807 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Reported by Robert Millan.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2801 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|