| Age | Commit message (Collapse) | Author |
|---|
|
Intel platforms use Low Power Idle Table (LPIT) to enumerate platform
Low Power Idle states. There are two types of low power residencies
a) CPU PKG C10 - read via MSR (Function fixed hardware interface)
b) Platform Controller Hub (PCH) SLP_S0 - read via memory mapped IO
Ref. https://www.uefi.org/sites/default/files/resources/Intel_ACPI_Low_Power_S0_Idle.pdf,
section 2.2.1: value of 0 indicates that counter runs at TSC frequency.
Ref. Intel 64 and IA-32 Architectures Software Developer’s Manual (Vol 4)
MSR 0x632: PC10 residency counter is at same frequency as the TSC.
Whereas slp_s0 residency counter running in different frequency.
BUG=b:300440936
TEST=check kernel cpuidle sysfs are created after kernel boot
cat /sys/devices/system/cpu/cpuidle/low_power_idle_cpu_residency_us
cat /sys/devices/system/cpu/cpuidle/low_power_idle_system_residency_us
Change-Id: Ibde764551a21b9aecb1c269948f4823548294711
Signed-off-by: Sukumar Ghorai <sukumar.ghorai@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78177
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
This patch implements an API to report the presence of an external
display on Intel silicon. The API uses information from the transcoder
and framebuffer to determine if an external display is connected.
For example, if the transcoder is attached to any DDI ports other than
DDI-A (eDP), and the framebuffer is initialized, then it is likely
that an external display is present.
This information can be used by payloads to determine whether or not
to power on the display, even if eDP is not initialized.
BUG=b:299137940
TEST=Build and boot google/rex
Scenarios:
Booting with eDP alone: has_external_display value is 0
Booting with eDP + HDMI: has_external_display value is 0
Booting with HDMI alone: has_external_display value is 1
Booting with USB-C display alone: has_external_display value is 1
Change-Id: I77436940978c7fa9368d79394b46a5e794c32e42
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78080
Reviewed-by: Julius Werner <jwerner@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Eric Lai <ericllai@google.com>
|
|
Intel GFX IP TRANS_DDI_FUNC_CTL register bit definitions have changed
since Tiger Lake.
This register is used to map ports and pipes to display controllers,
so reflecting the correct status is important for detecting physical
display end point devices.
This patch ensures that ADL, MTL, and TGL SoCs choose GMA version 2 to
properly reflect the updated port and pipe register definitions.
BUG=b:299137940
TEST=Build and boot google/rex successfully.
Change-Id: Ie2082747d18a5f136f410b1019be4d6c801617b1
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78079
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Eric Lai <ericllai@google.com>
|
|
Use the common UWES ACPI method to enable wake from USB. The only
difference to other SoCs is that JSL only has 8 USB2 ports, so the USB3
PORTSC register offset is different.
BUG=b:300844110
TEST=When enabled on taranza, all USB2 and USB3 ports can wake from
suspend
Change-Id: Ibc90246965d5d809123e954847543d28d78498a5
Signed-off-by: Reka Norman <rekanorman@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78086
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sheng-Liang Pan <sheng-liang.pan@quanta.corp-partner.google.com>
|
|
The ACPI methods for enabling USB wake are identical on ADL, CNL and
SKL. Move them to a common ASL file so they can be reused more easily
on other SoCs.
Also move the USB_PORT_WAKE_ENABLE macro used to create enable bitmasks
in devicetree to a common header.
BUG=b:300844110
TEST=Use abuild to build kinox, puff, and fizz with and without this
change. Check the generated dsdt.aml is unchanged.
Change-Id: Iabdfe2bece7fafc284ddf04382f1bbcacc370cce
Signed-off-by: Reka Norman <rekanorman@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78085
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
|
|
During CSE firmware downgrade, data is cleared. To preserve PSR data
during downgrade, it needs to be backed up. Select
SOC_INTEL_CSE_LITE_PSR config to ensure PSR backup related flow is
executed on CSE Lite SKU.
BRANCH=None
BUG=b:273207144
TEST=Verify CSE firmware upgrade/downgrade on rex.
Change-Id: I39af029a5f0c018a5db3ac68191764abfa9518ac
Signed-off-by: Krishna Prasad Bhat <krishna.p.bhat.d@intel.com>
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76115
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch adds eventlog entries for the below scenarios:
1. To indicate success or failure of PSR data back-up command
2. To indicate the loss of PSR data when CSE update is corrupted, and
data clear command is issued to clear the data.
3. To indicate the loss of PSR data when CSE boot partition info
response is corrupted and data back-up is not initiated.
BRANCH=None
BUG=b:273207144
TEST=Verify elog event added after PSR data backup command is sent
cse_lite: PSR_HECI_FW_DOWNGRADE_BACKUP command sent
...
ELOG: Event(B9) added with size 10 at 2023-06-27 06:44:49 UTC
Change-Id: I2459a2b941d28a87b6c78f75dbe8779d73328d7a
Signed-off-by: Krishna Prasad Bhat <krishna.p.bhat.d@intel.com>
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75760
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Anil Kumar K <anil.kumar.k@intel.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
Get PSR bit state using MKHI_FWCAPS_GET_FW_FEATURE_STATE HECI command
Use this bit info to check if SKU supports PSR and consequently issue
PSR_HECI_FW_DOWNGRADE_BACKUP command for PSR data backup during
downgrade.
BUG=b:273207144
TEST=build CB image and boot on google/rex board. Check for
"PSR is supported in this SKU" message in coreboot logs to confirm
that PSR bit is set in SKU
Signed-off-by: Anil Kumar <anil.kumar.k@intel.com>
Change-Id: I6e92341a9dc799146eb8f1a70b3a4a16fd1aa0ae
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74874
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
During CSE FW downgrade we erase CSE data. This would result in
Platform Service Record(PSR) data also to be erased.
To avoid losing PSR data we need to make a backup before data clear.
This patch sends PSR_HECI_FW_DOWNGRADE_BACKUP HECI command to CSE,
informing the CSE to backup PSR data before a data clear operation
during downgrade.
CMOS memory is used to track the backup status. PENDING is the default
state, it is updated to DONE once PSR_HECI_FW_DOWNGRADE_BACKUP HECI
command is sent.
PSR data can be backed up only post DRAM is initialized. The idea is to
perform cse_fw_sync actions in ramstage when PSR is enabled on a
platform. As part of the cse_fw_sync actions, when a firmware downgrade
is requested the command to back-up data is sent. Once the backup has
been done, trigger the firmware downgrade.
BRANCH=None
BUG=b:273207144
TEST=build CB image for google/rex board and check PSR backup command
is being sent during a CSE FW downgrade. Also check PSR data is not
lost/erased after a downgrade using intel PSR tool.
Change-Id: I135d197b5df0a20def823fe615860b5ead4391f8
Signed-off-by: Anil Kumar <anil.kumar.k@intel.com>
Signed-off-by: Krishna Prasad Bhat <krishna.p.bhat.d@intel.com>
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74577
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
PSR data is created and stored in CSE data partition. In platforms that
employ CSE Lite SKU firmware, a firmware downgrade involves clearing of
CSE data partition which results in PSR data being lost. The PSR data
needs to be preserved across the firmware downgrade flow. CSE Lite SKU
firmware supports command to backup PSR data. Since firmware downgrade
and PSR data backup flows involve global resets, there is a need to
track the PSR data backup status across resets. So adding a CMOS
variable for the same.
This patch implements API to access PSR backup status stored in CMOS.
The get API allows to retrieve the PSR backup status from CMOS memory.
The update API allows to update the PSR backup status in CMOS.
BRANCH=None
BUG=b:273207144
TEST=Able to retrieve PSR backup status across resets.
Change-Id: I270894e3e08dd50ca88e5402b59c211d7e693d14
Signed-off-by: Krishna Prasad Bhat <krishna.p.bhat.d@intel.com>
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77069
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
CSE firmware downgrade and PSR data backup flows involve global resets,
there is a need to track the PSR data backup status across resets. In
the subsequent patches, a CMOS structure to store PSR back-up status
will be added.
The current SOC_INTEL_CSE_FW_PARTITION_CMOS_OFFSET of 68 can only store
cse_specific_info, as ramtop is at offset 100 and PSR back-up status
structure will not be able to fit within the range.
This patch overrides the SOC_INTEL_CSE_FW_PARTITION_CMOS_OFFSET to 161
to accommodate all CSE related info in adjacent CMOS memory.
BUG=b:273207144
TEST=Verify CSE RW FW versions are stored in CMOS memory in rex.
Change-Id: I8bae5245f93b99be15b4e59cfeffbc23eec95001
Signed-off-by: Krishna Prasad Bhat <krishna.p.bhat.d@intel.com>
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78054
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Intel Platform Service Record(PSR) will be enabled on Meteor Lake
platforms. cse_fw_sync actions happen in ramstage when PSR is enabled.
To avoid the boot time penalty of sending the cse_get_bp_info in
ramstage, call cse_fill_bp_info to get cse_bp_info response early in
romstage and store in cbmem. This data can be later used in ramstage.
BUG=b:273207144
TEST=Verify cse_bp_info is filled in romstage in rex.
Change-Id: Ic0e8fb34f21ff07e182a7b848d38e9d329010028
Signed-off-by: Krishna Prasad Bhat <krishna.p.bhat.d@intel.com>
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78056
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Anil Kumar K <anil.kumar.k@intel.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
|
|
PSR data is created and stored in CSE data partition. In platforms that
employ CSE Lite SKU firmware, a firmware downgrade involves clearing of
CSE data partition which results in PSR data being lost. The PSR data
needs to be preserved across the firmware downgrade flow. CSE Lite SKU
firmware supports command to backup PSR data, and this command can be
sent only in post-RAM stages. So the cse_fw_sync actions needs to be
moved to ramstage.
Sending cse_get_bp_info command in ramstage takes additional boot time
of ~45-55ms on rex. To avoid the boot time penalty, this patch provides
an API to get the cse_bp_info in early romstage. The response data is
then migrated to cbmem once memory is initialized. The same data in
cbmem can be utilized in ramstage to perform other cse_fw_sync actions.
This patch also adds check to validate cse_bp_info in cbmem and avoids
sending the command again if the data is valid.
BUG=b:273207144
TEST=Verify the command works in early romstage, data is migrated to
cbmem and valid data is available in ramstage on rex.
Change-Id: Ib1e72c950ba0f4911924805f501ec1bd54b6ba3c
Signed-off-by: Krishna Prasad Bhat <krishna.p.bhat.d@intel.com>
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78053
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Now that Intel has publicly released FSP headers/binaries for
RaptorLake-P/S client platforms, set the defaults accordingly if
FSP_USE_REPO is not selected. This does not change any existing
defaults as the RaptorLake headers in vendorcode are only used when
FSP_USE_REPO is not set.
TEST=build/boot google/brya (osiris)
Change-Id: Ida92d269fcaf6f323599ec174f4dcedbbe65f03c
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78190
Reviewed-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sean Rhodes <sean@starlabs.systems>
|
|
PSR data is created and stored in CSE data partition. In platforms that
employ CSE Lite SKU firmware, a firmware downgrade involves clearing of
CSE data partition which results in PSR data being lost. The PSR data
needs to be preserved across the firmware downgrade flow. CSE Lite SKU
firmware supports command to backup PSR data, and this command can be
sent only in post-RAM stages. So the cse_fw_sync actions needs to be
moved to ramstage.
This patch ensures SOC_INTEL_CSE_LITE_SYNC_IN_RAMSTAGE is selected when
PSR is enabled.
BUG=b:273207144
Change-Id: I7c9bf8b8606cf68ec798ff35129e92cd60bbb137
Signed-off-by: Krishna Prasad Bhat <krishna.p.bhat.d@intel.com>
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78055
Reviewed-by: Anil Kumar K <anil.kumar.k@intel.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch selects LZ4 decompression for logo CBFS file. Able to save
2ms of the boot time when HAVE_FSP_LOGO_SUPPORT config is enabled.
However, the compressed BMP logo size is increased by ~2KB.
Raw BMP Image size is ~97KB.
BUG=b:284799726
TEST=Able to see pre-boot splash screen while booting google/redrix
with 32MB (W25Q256JWEIM) SPI-Flash.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I98e2c9a4f77d0b91f84eda9aec5060b236bd5e94
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78121
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Jasper Lake was missing these bases, so attempting to enable an SCI
would poke unrelated registers starting from offset 0. Set them so
GPEs can be enabled.
GPE is used on the Librem 11 for the keyboard dock connector, its sense
signal on GPP_D4 raises a GPE which is used to indicate tablet/laptop
mode to the OS.
The register offsets are documented in the datasheet volume 2 (Intel
document 634545), all groups' GPE_STS/GPE_EN start at the same offsets.
Change-Id: Ib6b9b9a79e9cc4467e609eaf591ec4e87b78d617
Signed-off-by: Jonathon Hall <jonathon.hall@puri.sm>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78097
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Rather than disabling C State demotions for every single Raptor
Lake board due to an issue with S0ix, regardless of if they even
use S0ix, configure it in the mainboard.
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Change-Id: I4f941a549bc717ae2f8ec961ead7ac7668347c99
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77087
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
|
|
Currently the HDA device can neither be disabled using softstraps
nor can it be disabled by using FSP UPDs. Add code to disable it in
coreboot when it's marked as 'off' in coreboot's devicetree.
TEST: Device 00:1f.3 is hidden and platform boots into OS without issue.
Change-Id: Ifa1422d653cf81ee6faf2bdda27a471c2084642b
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77873
Reviewed-by: David Hendricks <david.hendricks@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This reverts commit 21e61847c4cf643d79855deba8f58fd45808d571.
Reverting as it breaks booting on google/dedede based boards. First boot
after flashing is successful, 2nd hangs with the following error:
[EMERG] FspMemoryInit returned with error 0x80000003!
TEST=build/boot google/dedede (magpie, metaknight)
Change-Id: I6a2474617b444414c4248dbeda23ed0915704a17
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78091
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sean Rhodes <sean@starlabs.systems>
Reviewed-by: Jonathon Hall <jonathon.hall@puri.sm>
|
|
cse_store_rw_fw_version() stores CSE RW firmware version in global
variable or cbmem in romstage and ramstage respectively, based on the
stage it is called in. The call to this function is from the
cse_print_boot_partition_info() in cse_get_bp_info.
In the subsequent patches, the idea is to send the cse_get_bp_info early
in romstage and store in cbmem once memory is initialized. So when the
cse_fw_sync is called in early ramstage, the stored cse_bp_info_rsp is
used instead of sending the CSE get boot partition info command again.
To de-link the call to cse_store_rw_fw_version from cse_get_bp_info and
to ensure the CSE RW FW version is stored in all cases, moving the
function to do_cse_fw_sync.
BUG=b:273207144
Change-Id: I0add2c167c85cbddef2ecb4c019061a08562bbdf
Signed-off-by: Krishna Prasad Bhat <krishna.p.bhat.d@intel.com>
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78051
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: sridhar siricilla <siricillasridhar@gmail.com>
|
|
PSR data is created and stored in CSE data partition. In platforms that
employ CSE Lite SKU firmware, a firmware downgrade involves clearing of
CSE data partition which results in PSR data being lost.
CSE Lite SKU firmware supports a command to backup PSR data before
initiating a firmware downgrade. PSR data backup command works only
after memory has been initialized. Moving only the downgrade would add
complexity of splitting the cse_fw_sync across pre-RAM and post-RAM
stages. So the idea is to move cse_fw_sync into ramstage when PSR is
enabled.
We are introducing a flow to get CSE boot partition info in early
romstage and then same data will be stored in cbmem once DRAM is
initialized. The CSE BP info data in cbmem will be utilized in early
ramstage to perform cse firmware sync operations. This helps in avoiding
re-sending the CSE get boot partition info command in ramstage. Having
cse_bp_info_rsp as global helps in de-linking cse_get_bp_info from
cse_fw_sync.
Many functions take cse_bp_info as input parameter. Since
cse_bp_info_rsp is global now, we can make use of global cse_bp_info and
remove it as input parameter from those functions.
BUG=b:273207144
TEST=Verify cse_bp_info_rsp holds value across the stage.
Change-Id: I0ee050b49fcae574882378b94329c36a228e6815
Signed-off-by: Krishna Prasad Bhat <krishna.p.bhat.d@intel.com>
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77070
Reviewed-by: sridhar siricilla <siricillasridhar@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Anil Kumar K <anil.kumar.k@intel.com>
|
|
Enable upd to reduce size of the memory test.
BUG=b:301441204
TEST=Able to build and boot google/rex.
w/o this patch:
951:returning from FspMemoryInit 650,922 (79,560)
w/ this patch:
951:returning from FspMemoryInit 618,490 (45,621)
Change-Id: I903591ec749d270a98895dafb2d8f8d0b287c26a
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78067
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Jakub Czapiga <jacz@semihalf.com>
Reviewed-by: Jérémy Compostella <jeremy.compostella@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Dinesh Gehlot <digehlot@google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
|
|
Hook the newly exposed LowerBasicMemTestSize UPD up so that boards
can configure it via devicetree.
BUG=b:301441204
TEST=Verified by enabling/disabling the UPD on google/rex.
Change-Id: Iec466aeaebd72f222d97f720a85bbb8c27e26325
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78066
Reviewed-by: Jakub Czapiga <jacz@semihalf.com>
Reviewed-by: Jérémy Compostella <jeremy.compostella@intel.com>
Reviewed-by: Dinesh Gehlot <digehlot@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
commit 06cb756f0202d7 ("soc/intel/common/block/cse/Kconfig: Remove
unused symbols") removed these Kconfigs since it's not obvious where
they're used. Add a comment to make it easier to grep for their uses.
Change-Id: I27d94e8a558d6e73004d45cd2aedd94678d29b94
Signed-off-by: Reka Norman <rekanorman@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78041
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This reverts commit 06cb756f0202d78d299b30728b6559f6107c43c3.
Reason for revert: These Kconfigs are needed by boards which use the
CSE stitching tools (i.e. select STITCH_ME_BIN). They're selected by
some boards in the downstream ChromeOS repo. They're used in
src/soc/intel/Makefile.inc (see the line with
`$(CONFIG_CSE_$(2)_FILE)`).
Change-Id: Ide6fc74b457439f06b7ef9b37f11d6c9ff226b80
Signed-off-by: Reka Norman <rekanorman@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76719
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Hook up the OC watchdog common block and initialize it if requested.
TEST=Enable watchdog on MSI PRO Z690-A and see the platform resets
after some time. Enable the watchdog in driverless mode and see the
platform no longer resets and periodic SMI keeps feeding the watchdog.
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Change-Id: I1c2c640d48b7e03ad8cd8d6cdf6aac447e93cd86
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68945
Reviewed-by: Krystian Hebel <krystian.hebel@3mdeb.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Reduce the OC WDT integration code footprint by consolidating
multiple API calls into a single function to be called by SoC.
Change-Id: Iba031cd8e0b72cabc4d0d8a216273d763231c889
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77574
Reviewed-by: Krystian Hebel <krystian.hebel@3mdeb.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Certain Intel Meteor Lake specific features are only enabled in
production silicon (not available in early SoC aka pre-production
silicon).
- SPI usage for production SoC is much optimized compared to pre-
production silicon.
- MIPI driver requires a way to identify between pre-prod vs prod
silicon.
This patch adds config options to select the Pre-Production
aka Engineering Silicon (ES). The mainboard users can specify which
underlying SoC is being used for the target platform.
BUG=b:300652989
TEST=No change in the functionality, just added new configs.
Change-Id: I60fe11c1151a3a6c290cd0105eb570cb78e81797
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77991
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Jakub Czapiga <jacz@semihalf.com>
Reviewed-by: Jamie Ryu <jamie.m.ryu@intel.com>
|
|
Enable SOC_INTEL_CRASHLOG and SOC_INTEL_IOE_DIE_SUPPORT Kconfig
options.
BUG=b:262501347
TEST=Able to build google/rex. Able to trigger and decode crashlog.
Change-Id: I4beef7393090889fde8d67827035c3b57a3dbb34
Signed-off-by: Pratikkumar Prajapati <pratikkumar.v.prajapati@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77583
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
|
|
Added Raptor Lake U graphics device ids.
Renamed Raptor Lake U graphics device ids that were marked as
Raptor Lake P.
Added Raptor Lake P graphics device ids.
References:
RaptorLake External Design Specification Volume 1 (640555)
TEST=Boot to OS
Signed-off-by: Bora Guvendik <bora.guvendik@intel.com>
Change-Id: I44734f927764f872b89e3805a47d16c1ffa28865
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77898
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I9a9926a7298bca0ca5b67a59124b1e0471e179c4
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77729
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
cpu_cl_cleanup() function checks if the SOC supports storage-off
feature. This feature allows to turn off PUNIT SSRAM to save power.
Enable the storage-off if it's supported. Enabling it also clears the
crashlog records from PUNIT SSRAM.
cpu_cl_rearm() function rearms the CPU crashlog.
BUG=b:262501347
TEST=Able to build google/rex. Verified both features get asserted.
Change-Id: Id9ba0f5db0b5d2bd57a7a21f178ef1e86ca63fae
Signed-off-by: Pratikkumar Prajapati <pratikkumar.v.prajapati@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77239
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add more details in CPU crashlog header structure, such as
storage off status and support, re-arm status etc. These fields
are used to check of particular feature is supported or not and
if supported what is the status of the feature.
BUG=b:262501347
TEST=Able to build google/rex.
Change-Id: I4242b6043b8f8ad9212780f44ca0448cd2b6b9f8
Signed-off-by: Pratikkumar Prajapati <pratikkumar.v.prajapati@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77562
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Introduce cpu_cl_cleanup() and cpu_cl_rearm() functions
for CPU crashlog flow. Also add default weak implementations.
BUG=b:262501347
TEST=Able to build google/rex.
Change-Id: Iad68d3fdaf7061148b184371f7ef87d83f2b2b38
Signed-off-by: Pratikkumar Prajapati <pratikkumar.v.prajapati@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77238
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Not all SOC follow the same programming to clear crashlog
data. So make common implementation of cpu_cl_clear_data()
weak.
BUG=b:262501347
TEST=Able to build google/rex.
Change-Id: Ic2b4631d57703abff0ab1880fb272ef67bb1b8e9
Signed-off-by: Pratikkumar Prajapati <pratikkumar.v.prajapati@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77237
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
relanding original commit 5013c60a871af8fbce8c38a1c342c454e5b8452f
("soc/intel/meteorlake: Generate new TME key on each warm boot") which was previously reverted by commit 19e66b7c951ce71a1b9bc20158af56e559f8a58f
(Revert "soc/intel/meteorlake: Generate new TME key on each warm boot")
due to consecutive reboot post warm reset issue.
The consecutive reboot post warm reboot issue has been fixed with
commit ba7a9eefcf4e571bc73d4be1141f676fc5547057 ("soc/intel/common: Fix
invalid MADT entries creation"), hence, reattempting to land the original TME key related patch.
BUG=299294328
TEST=Boot up the system, generate kernel crash using following
commands:
$ echo 1 > /proc/sys/kernel/sysrq
$ echo "c" > /proc/sysrq-trigger
System performs warm boot automatically. Once it is booted,
execute following commands in linux console of the DUT and confirm
ramoops can be read.
$ cat /sys/fs/pstore/console-ramoops-0
Signed-off-by: Anil Kumar <anil.kumar.k@intel.com>
Change-Id: I5d45d265ccef1a7d37669ea22a74b52e2f3ae20d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77902
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Pratikkumar V Prajapati <pratikkumar.v.prajapati@intel.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
DRIVERS_INTEL_MIPI_SUPPORTS_PRE_PRODUCTION_SOC is added to mipi camera
driver to extend the same support for all SoCs, so removing this config
from Alderlake SoC code.
BUG=None
TEST=Build rex and brya to check if the build passes without an
error.
Change-Id: I5bc23fce89f0ae22b64b90cb12621320cac30d85
Signed-off-by: Jamie Ryu <jamie.m.ryu@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77859
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Bora Guvendik <bora.guvendik@intel.com>
|
|
Change-Id: Icc7974931a9b3f5b5c7a2ed4df2c668dac0cd684
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77872
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
|
|
Change-Id: Ib365a17652b8531e865fa16eae837c68cbedbca8
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77871
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Reviewed-by: Naresh <naresh.solanki.2011@gmail.com>
|
|
Move the existing FSP 4221.00 headers for Raptor Lake to a
subdirectory called 4221.00_google, and select this if the
vendor is Google.
Add the standard FSP 4301.01 headers to a separate directory,
from Intel download #686654, and select this for all other
vendors.
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Change-Id: Icd99bdee1eeac70dfcaca3d07150d3de6bb83d81
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77101
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
BUG=b:264960828
TEST=On dibbi, ACPI tables contain entries for USB 3.4 and 3.5
Change-Id: If3266d356a2deaf42aa0943f85593416d80637ad
Signed-off-by: Reka Norman <rekanorman@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77866
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sam McNally <sammc@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
The PMC and P2SB IDs for Raptor Lake-S PCH were missing. Add them based
on doc 619362 rev 2.2.
Change-Id: I5de00adf2d87cf50571abb02b28e7feebdc3911e
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77448
Reviewed-by: Tim Crawford <tcrawford@system76.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
This patch addresses the increased boot time issue that occurs when ISH
store is enabled, such as in the "rex4es_ec_ish" variant.
During a cold reboot, the CBMEM memory resets and loses the stored
firmware versions. This causes the firmware versions to be fetched again
from the CSE, which increases the boot time by about 200 ms. This patch
stores a backup of the firmware version in CMOS and updates the CBMEM
memory during a cold reboot.
BUG=b:280722061
Test=Verified the changes on rex board.
Signed-off-by: Dinesh Gehlot <digehlot@google.com>
Change-Id: Ibc5a027aa2bb7217e5032f56fece0846783557a5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75755
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch implements APIs to access the CSE FW partition versions in
CMOS. The get API allows users to retrieve the current version from
CMOS memory. The set API allows users to set the version in CMOS
memory.
BUG=b:280722061
TEST=APIs verified on rex board.
Signed-off-by: Dinesh Gehlot <digehlot@google.com>
Change-Id: Idd0ee19575683691c0a82a291e1fd3b2ffb11786
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74995
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
|
|
Remove the check to follow the new flow that commit 9c348a7b7ea3
("soc/intel/alderlake: Fix processor hang while plug unplug of
TBT device") introduced.
Processor hang is observed while hot plug unplug of TBT device. BIOS
should execute TBT PCIe RP RTD3 flow based on the value of
TBT_DMA_CFG_VS_CAP_9[30]. It should skip TBT PCIe RP RTD3 flow, if
BIT30 in TBT FW version is not set.
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Change-Id: Ie822b8e1fd7592a31275db8455519c4cc6ac02ad
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77456
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
Change-Id: Ibf28fbdf791e7aa2faa41f3059150bf5ff5d21d1
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77735
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
x86 pre-memory stages do not support the `.data` section and as a
result developers are required to include runtime initialization code
instead of relying on C global variable definition.
To illustrate the impact of this lack of `.data` section support, here
are two limitations I personally ran into:
1. The inclusion of libgfxinit in romstage for Raptor Lake has
required some changes in libgfxinit to ensure data is initialized at
runtime. In addition, we had to manually map some `.data` symbols in
the `_bss` region.
2. CBFS cache is currently not supported in pre-memory stages and
enabling it would require to add an initialization function and
find a generic spot to call it.
Other platforms do not have that limitation. Hence, resolving it would
help to align code and reduce compilation based restriction (cf. the
use of `ENV_HAS_DATA_SECTION` compilation flag in various places of
coreboot code).
We identified three cases to consider:
1. eXecute-In-Place pre-memory stages
- code is in SPINOR
- data is also stored in SPINOR but must be linked in Cache-As-RAM
and copied there at runtime
2. `bootblock` stage is a bit different as it uses Cache-As-Ram but
the memory mapping and its entry code different
3. pre-memory stages loaded in and executed from
Cache-As-RAM (cf. `CONFIG_NO_XIP_EARLY_STAGES`).
eXecute-In-Place pre-memory stages (#1) require the creation of a new
ELF segment as the code segment Virtual Memory Address and Load Memory
Address are identical but the data needs to be linked in
cache-As-RAM (VMA) but to be stored right after the code (LMA).
Here is the output `readelf --segments` on a `romstage.debug` ELF
binary.
Program Headers:
Type Offset VirtAddr PhysAddr FileSiz MemSiz Flg Align
LOAD 0x000080 0x02000000 0x02000000 0x21960 0x21960 R E 0x20
LOAD 0x0219e0 0xfefb1640 0x02021960 0x00018 0x00018 RW 0x4
Section to Segment mapping:
Segment Sections...
00 .text
01 .data
Segment 0 `VirtAddr` and `PhysAddr` are at the same address while they
are totally different for the Segment 1 holding the `.data`
section. Since we need the data section `VirtAddr` to be in the
Cache-As-Ram and its `PhysAddr` right after the `.text` section, the
use of a new segment is mandatory.
`bootblock` (#2) also uses this new segment to store the data right
after the code and load it to Cache-As-RAM at runtime. However, the
code involved is different.
Not eXecute-In-Place pre-memory stages (#3) do not really need any
special work other than enabling a data section as the code and data
VMA / LMA translation vector is the same.
TEST=#1 and #2 verified on rex and qemu 32 and 64 bits:
- The `bootblock.debug`, `romstage.debug` and
`verstage.debug` all have data stored at the end of the `.text`
section and code to copy the data content to the Cache-As-RAM.
- The CBFS stages included in the final image has not improperly
relocated any of the `.data` section symbol.
- Test purposes global data symbols we added in bootblock,
romstage and verstage are properly accessible at runtime
#3: for "Intel Apollolake DDR3 RVP1" board, we verified that the
generated romstage ELF includes a .data section similarly to a
regular memory enabled stage.
Change-Id: I030407fcc72776e59def476daa5b86ad0495debe
Signed-off-by: Jeremy Compostella <jeremy.compostella@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77289
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
When using Intel(R) Xeon(R) Platinum 8490H on IBM/SBP1 the platform runs
with 480 cores. With 480 cores coreboot needs at least 440KiB for ACPI
tables. Bump the config to 512 KiB to have some free space for future
changes.
Change-Id: I2c0bbc36f45aab921f3189459de4438a0cd5dd1f
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77715
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Naresh <naresh.solanki.2011@gmail.com>
|
|
When CSE jumps between RO and RW, it triggers global reset so the
AP goes down to S5 and back to S0. For Chromebox, when AP goes
down to S5 EC set AP_IDLE flag. This cause an issue to warm reset
the Chromebox device when it is in recovery mode and powered by
USB-C adapter. This patch allows AP to direct EC to clear AP_IDLE
flag before trigger reset.
BUG=b:296173534
BRANCH=firmware-dedede-136-6.B
TEST=Chromebox DUT which is powered by USB-C adapter boots up
after warm reset in recovery mode
Change-Id: Ib0002c1b8313c6f25d2b8767c60639aed8a4f904
Signed-off-by: Derek Huang <derekhuang@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77632
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Reka Norman <rekanorman@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Daisuke Nojiri <dnojiri@google.com>
|
|
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Change-Id: I8515407eb10e1a74f37ea5a80fa31533c38badec
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77455
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The ensures that ITBT is ready to operate.
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Change-Id: If60404a88208c632cd60e8aaa6ba70494eefbed2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77454
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
The ACPI used for Tiger Lake, Alder Lake and Meteor Lake are very
similar, so can be moved to shared code.
This commit aligns minor difference between then, such as comments and
tabs/spaces.
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Change-Id: If6554c7ef9e83740d7ec5dcca6a9d7e32fb182db
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77453
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
commit f8ac3dda02f22ebf857efb5b845db97f00598f7d ("soc/intel/common:
Order the CPUs based on their APIC IDs") sort algorithnm walks all the
`cpu_info' entries without discarding empty ones. Since `cpu_info' is
not initialized, the data that is used is undefined and it generally
results in the creation of invalid `Local x2APIC' entries in the
MADT ("APIC") ACPI table.
Depending on the X2APIC ID value the Linux kernel behavior
changes (cf. arch/x86/kernel/acpi/boot.c::acpi_register_lapic()):
1. If (int)ID >= MAX_LOCAL_APIC (32768), the Linux kernel discards the
entry with the "skipped apicid that is too big" INFO level
message.
2. If (int)ID < MAX_LOCAL_APIC (32768) (including negative) this data
is taken into account and it can lead to undesirable behavior such
as core being disabled as (cf. "native_cpu_up: bad cpu" ERROR
kernel message).
TEST=Verified the MADT does not contain any invalid entries on rex.
Change-Id: I19c7aa51f232bf48201bd6d28f108e9120a21f7e
Signed-off-by: Jeremy Compostella <jeremy.compostella@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77615
Reviewed-by: Bora Guvendik <bora.guvendik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
|
|
It makes the detection of this feature accessible without the
CONFIG_SOC_INTEL_COMMON_BLOCK_CPU dependency.
BUG=288978352
TEST=compilation
Change-Id: I005c4953648ac9a90af23818b251efbfd2c04043
Signed-off-by: Jeremy Compostella <jeremy.compostella@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77697
Reviewed-by: Bora Guvendik <bora.guvendik@intel.com>
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I1dbfca33c437c680118eb3a92e60b5607c93e565
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77768
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I57b54653bd29a728825210403c8f426eb1c9cc48
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75633
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Sean Rhodes <sean@starlabs.systems>
|
|
This patch ensures that the LidStatus UPD is passed a dynamic value,
rather than always passing 1 (CONFIG_RUN_FSP_GOP enabled) for FSP 2.0
devices.
Problem statement:
* FSP-S GFX PEIM initializes the on-board display (eDP) even when the
LID is physically closed, because LidStatus is always set to 1.
* FSP-S skips external display initialization even when the LID is
closed.
Solution:
* FSP-S GFX PEIM module understands the presence of an external display
if LidStatus is not set, and tries to probe the other display
endpoint.
* Statically passing LidStatus as always enabled (aka 1) does not
illustrate the exact device scenarios, so this patch updates
LidStatus dynamically by reading the EC memory map offset.
BUG=b:299137940
TEST=Able to build and boot google/rex to redirect the display
using external HDMI monitor while LID is closed.
Change-Id: I7d7b678227a6c8e32114de069af8455b8c1aa058
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77685
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
Change-Id: I9ecd81ffaa48dbed225a23900704b259569cb7c8
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77527
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch renames `SAVE_MRC_AFTER_FSPS` config to
`FSP_NVS_DATA_POST_SILICON_INIT` to highlight the violation in the Xeon
SP FSP implementation, where the FSP Silicon Init API produces
Non-Volatile Storage (NVS) instead of the FSP-Memory Init API.
According to the FSP 2.x specification (section 11.3), the FSP
populates the NVS data using the FSP_NON_VOLATILE_STORAGE_HOB and
expects the boot firmware to parse the FSP_NON_VOLATILE_STORAGE_HOB
after the FspMemoryInit() API in API mode.
However, not all Intel SoC platforms that support the FSP 2.x
specification adhere to this requirement. For example, the FSP binary
for XEON SP platform produces NVS data (aka
FSP_NON_VOLATILE_STORAGE_HOB) after the FspSiliconInit() API.
Therefore, attempting to locate NVS data after the FspMemoryInit() API
on these platforms would result in an error. The `save_mrc_data.c`
implementation provides the required hooks to locate the NVS post
FSP-Silicon Init and store into Non-Volatile Storage.
BUG=b:296704537
TEST=Able to build and boot Intel Xeon SP w/o any functional impact.
Change-Id: I815a64263fa1415bfe30bb3c1c35e4adee307e86
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77616
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Johnny Lin <Johnny_Lin@wiwynn.com>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
|
|
This patch ensures that the VR configuration for IA, SA, and GFX is
properly initialized, assigning zero values to VR causes a black screen
(no display) issue.
Problem Statement:
Override CEP (Current Excursion Protection) value with zero aka set to
disable results into black screen issue (no display).
Solution:
Keep CEP default enabled and don't override w/ zero value.
w/o this patch:
[SPEW ] CPU_POWER_MGMT_VR_CONFIG : CepEnable[0] : 0x0
[SPEW ] CPU_POWER_MGMT_VR_CONFIG : CepEnable[1] : 0x0
[SPEW ] CPU_POWER_MGMT_VR_CONFIG : CepEnable[2] : 0x0
w/ this patch:
[SPEW ] CPU_POWER_MGMT_VR_CONFIG : CepEnable[0] : 0x1
[SPEW ] CPU_POWER_MGMT_VR_CONFIG : CepEnable[1] : 0x1
[SPEW ] CPU_POWER_MGMT_VR_CONFIG : CepEnable[2] : 0x1
Change-Id: I8908e8b6c995390b559212d456db6ddf984448a3
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77611
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eran Mitrani <mitrani@google.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
|
|
All of the SoCs in the cannonlake directory select the following
options. So move them to the common option SOC_INTEL_CANNONLAKE_BASE
in order to deduplicate selections.
* FSP_USES_CB_STACK
* HAVE_INTEL_FSP_REPO
* SOC_INTEL_CONFIGURE_DDI_A_4_LANES
Change-Id: I6ce5edb2ba2c138b44601b32c3ecba2e761136f7
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77447
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
|
|
Intel Cannon Lake was removed with commit d456f65056. Thus, remove this
dead code.
Change-Id: I53cd9d53b01e26f530684aa9c404f50b305c1f54
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77446
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
|
|
Add SA_DEV_SLOT_GNA definition to SoCs missing it, so the name
resolves properly.
TEST=tested with rest of patch train
Change-Id: I31c8b14e5083fc8e212a4e32330125fa72696c73
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Signed-off-by: CoolStar <coolstarorganization@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77576
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
Allows boards which enable the GNA device to provide an attachment
point for the OS drivers.
TEST=tested with rest of patch train
Change-Id: I3398eefb80e4407594883dd39128cd7885105ac3
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Signed-off-by: CoolStar <coolstarorganization@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77528
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
Remove MAILBOX word from CPU_CRASHLOG_MAILBOX_WAIT_STALL
and CPU_CRASHLOG_MAILBOX_WAIT_TIMEOUT macros, because they
can be used for other interface as well.
BUG=b:262501347
TEST=Able to build google/rex.
Change-Id: I62b04fa4b05c427db494a536ca6504db02dfeb68
Signed-off-by: Pratikkumar Prajapati <pratikkumar.v.prajapati@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77236
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Region with metadata tag contains information about BDF entry for
SOC PMC SRAM and IOE SRAM. We don't need to parse this as we already
define BDFs in soc/pci_devs.h for these SRAMs. Also we need to skip
to region as it does not contain any crashlog data.
BUG=b:262501347
TEST=Able to build google/rex. Able to trigger crashlog and decode
correctly.
Change-Id: Id8ed40b865cde8e89045f5c9e713398fcbff5890
Signed-off-by: Pratikkumar Prajapati <pratikkumar.v.prajapati@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76834
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
When parsing descriptor table the record can have tag type = 7.
This tag contains metadata depending on SOC. The platform may
choose to parse it based on implementation of crashlog.
BUG=b:262501347
TEST=Able to build google/rex.
Change-Id: I60dda06950974f7949fa5635141e4b7798c4d1f2
Signed-off-by: Pratikkumar Prajapati <pratikkumar.v.prajapati@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76833
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
CPU crashlog discovery table and crashlog record is considered
invalid if first 32bits of the table is either 0x0 (no crashlog)
or 0xdeadbeef (invalid crashlog).
Crashlog record is considered consumed if bit 31 is set. So in this
case stop processing the subsequent records.
BUG=b:289600699
TEST=Able to build and verified invalid records are skipped on
google/rex.
Change-Id: Ia81bd293a533217425e44473ae85b2115c85faf6
Signed-off-by: Pratikkumar Prajapati <pratikkumar.v.prajapati@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76333
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
CPUID CPUID_METEORLAKE_B0 onwards the discovery table offset needs
to be left-shifted by 3.
Reference: EDS Vol 1 (640228)
BUG=b:289600699
TEST=Able to boot google/rex with crashlog enabled.
Change-Id: I90647fb6190a52b42298398263978beaf931b035
Signed-off-by: Pratikkumar Prajapati <pratikkumar.v.prajapati@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76400
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
Older FSP releases don't have an option to do MP init via PPI, so it
should not be visible.
Change-Id: I74b4bd5dd72980b859763e89ead7d7f619321e66
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63759
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch adds option to override Fast Vmode on Meteor Lake SoC.
This requires CepEnable, EnableFastVmode, IccLimit FSPM UPDs in FSP
header. If the hardware supports Fast Vmode, the FSPM will set the
ICC limit value to the value passed from coreboot.
With CepEnable and EnableFastVmode enabled, if IccLimit is not
specified by coreboot, FSPM sets IccLimit as default value. If no
values assigned to all the three CepEnable, EnableFastVmode and
IccLimit, coreboot sets their values to 0 and Fast Vmode is disabled.
BUG=b:286809233
TEST=In debug MTL FSP logs, the value of FSP parameters is as passed
from coreboot including enable_fast_vmode, cep_enable, and
fast_vmode_i_trip. Also, fast_vmode_i_trip value is passed to pcode
using mailbox command without any error. This test done on google/rex
board.
Signed-off-by: Jay Patel <jay2.patel@intel.com>
Change-Id: Id05dccac56c504523f9327babe0c6fbeff488ec2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75566
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jakub Czapiga <jacz@semihalf.com>
|
|
This reverts commit 5013c60a871af8fbce8c38a1c342c454e5b8452f.
Reason for revert: consecutive reboots are causing kernel panic.
BUG=b:297153853
TEST=Able to perform 50 cycles of consecutive reboot after reverting
this CL and it boots to the OS every single time(w/o any kernel panic).
Change-Id: If6c96dcc62c706a522b98a1cf1dd1920ad6473a1
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77467
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Ivy Jian <ivy.jian@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add new block for handling overclocking watchdog. The watchdog is
present since Skylake or maybe even earlier so it is safe to use with
most of the microarchitectures utilizing intelblocks.
The patch adds the common block for initializing and feeding the
watchdog. Timeout is defined statically in Kconfig and should be set
high enough by the board or SoC Kconfig to let the board boot with
full memory training and avoid reset loops. Full training of 128GB
DDR5 DIMM memory on AlderLake takes about 5 minutes. Newer SoCs
with newer memory technologies and higher RAM capacity may take more.
The default has been set to 10 minutes.
The patch also adds support for feeding watchdog in driverless mode,
i.e. it utilizies periodic SMI to reload the timeout value and restart
the watchdog timer. This is optional and selectable by Kconfig option
as well. If the option is not enabled, payload and/or software must
ensure to keep feeding the watchdog, otherwise the platform will
reset.
TEST=Enable watchdog on MSI PRO Z690-A and see the platform resets
after some time. Enable the watchdog in driverless mode and see the
platform no longer resets and periodic SMI keeps feeding the watchdog.
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Change-Id: Ib494aa0c7581351abca8b496fc5895b2c7cbc5bc
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68944
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Krystian Hebel <krystian.hebel@3mdeb.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add two missing mapping for GPIO GPE routes
Signed-off-by: Cliff Huang <cliff.huang@intel.com>
Change-Id: I3f0d13cf7c07201856e934f22efc4cc8c4ea5bf0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77423
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The `use_8254` should be flipped, the same as the other Intel
SOCs.
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Change-Id: I2d6c859c0910b796d2ae5874a560ff9974578106
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77409
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
|
|
Those values need to match with the ones defined in PMC PWRM
GPIO CFG register.
Signed-off-by: Cliff Huang <cliff.huang@intel.com>
Change-Id: I8e84df83caab794e2fe7186e89e78343c2b55fd0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76536
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
Add a pmc.h file, which is needed for OC watchdog compilation. The PMC
definitions from pm.h are moved to pmc.h.
TEST=Build UP Squared and Intel GLKRVP sucessfully.
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Change-Id: I2726aaae1ce60d15a3944dadcf793def2dcb3a1c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69900
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Krystian Hebel <krystian.hebel@3mdeb.com>
|
|
Change-Id: If3c2e5bd9ee7e0f77d0c39ffe2ca9ad17b77d9bd
Signed-off-by: Michael Strosche <michael.strosche@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77373
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
|
|
Set EnforceDdrMemoryFreqPor to 0 for RMT builds. This is needed
for proper functioning when EnforcePopulationPor is set to 1.
Signed-off-by: Naresh Solanki <Naresh.Solanki@9elements.com>
Change-Id: Icf4fe01ac9b546830334717dbfa53782d2a85ba1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77339
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
Move specific options under the boolean and remove dummy
SOC_SPECIFIC_OPTIONS.
Change-Id: I6ae52ceb61489e5a050a60d1fbbf4250960407eb
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76487
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
|
|
The RPL PCH uses a different ACPI Device ID than ADL PCH.
Ref: Intel 700 Series Chipset Family PCH Datasheet, Volume 1 (#743835)
Change-Id: I03f47a43ff985213ad617e834db7f974f687d877
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77150
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
Similar situation happened last year when IoT FSP for ADL-S came out
before the Client FSP variant: https://github.com/intel/FSP/issues/83
It seems IoT FSP publishes the MemInfoHob.h file much later due to
legal reasons. Hack the missing file to get the builds using RPL-S IoT
FSP from repo working properly.
This change could be merged, subject for later revert (when the header
file is published).
Change-Id: Iec35db4573a3c3d011e4c1edf1c82a5c34438695
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76324
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jan Samek <jan.samek@siemens.com>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
|
|
PchPcieClockGating and PchPciePowerGating UPDs are not yet available
in RPL-S IOT FSP. It also looks like those UPDs are not generally
available in all public RaptorLake FSP headers yet, so guard it
against SOC_INTEL_RAPTORLAKE to avoid build errors.
Change-Id: Iedac21bafa3428957e054fc8fefa38f9f776772d
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77337
Reviewed-by: Jan Samek <jan.samek@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
|
|
Change-Id: I21db0474157ba20cdf3eaef086aaf29fde29d6c5
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76701
Reviewed-by: Martin L Roth <gaumless@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I6f2dc0fcc4392f77b8011221c0cf22af5da45172
Signed-off-by: Michael Strosche <michael.strosche@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77276
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
|
|
Remove unused HPET_BASE_ADDRESS.
It is already defined at <arch/hpet.h>.
Change-Id: I8c517283e56915873b8e1798571642fd9d8a5764
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77325
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Jakub Czapiga <jacz@semihalf.com>
|
|
broadwell/pch/Kconfig is sourced if SOC_INTEL_BROADWELL is true. So
remove 'if SOC_INTEL_BROADWELL' condition and duplicated
'INTEL_LYNXPOINT_LP'
Change-Id: I9b5676fd232b47e9d5f89f7faffdfd5d2c76984e
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76699
Reviewed-by: Martin L Roth <gaumless@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
IOE_PMC support was not enabled on Meteor Lake platforms. This patch
adds the bare minimum hooks to initialize and allocate a memory region
for IOE operations. Additionally, this patch moves those IOE operations
to a newly included IOE-specific file, Previously, PMC was responsible
for these operations.
BUG=b:287419766
TEST=build and verified on google/rex.
Change-Id: I8bbc0b8a3e32dad5404c80bc7717ef07e3ec60b9
Signed-off-by: Dinesh Gehlot <digehlot@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77261
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Allow users of Alderlake N processors to use the microcode repository
and also add their related microcode blob to the list of microcodes
which should be included in the coreboot rom.
Change-Id: I11c9cb13fa81118bfcb819bad5fb39731c7e3e76
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75632
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nicholas Chin <nic.c3.14@gmail.com>
|
|
This patch implements `soc_is_ish_partition_enabled()` override to
uniquely identify the SKU type between ISH and non-ISH to conclude
if ISH partition is enabled and need to retrieve the ISH version from
CSE FPT by sending a HECI command.
BUG=b:285405031
TEST=Able to uniquely identify the ISH SKUs while booting
to google/rex_ec_ish to dump the ISH version.
Change-Id: I48358ad9e2e582e8b2274cbf4655de01f8792e6c
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77177
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Dinesh Gehlot <digehlot@google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch uses the CSE firmware specific data to store Intel
ISH firmware related information. Sending an ISH partition version
information command on every boot cycle would impact the overall boot
performance.
This information is used by the auto-test framework to ensure the ISH
firmware update is proper for in-field devices.
BUG=b:285405031
TEST=Able to build and boot google/rex. Verified ISH FW version is
getting displayed across warm resets without impacting the boot time.
Change-Id: I0242c26dd90d834815799f54740d8147ff9d45b7
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77176
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
This patch selects SOC_INTEL_STORE_CSE_FW_VERSION config by default
for CSE LITE SKU. It helps to dump the CSE RW firmware version which
further consumed by auto-test infrastructure to ensure CSE RW firmware
update is successful.
BUG=b:285405031
TEST=Able to build and boot google/rex.
Verified CSE RW FW version (for LITE SKU) is getting displayed without
impacting the boot time.
Change-Id: Iba5903c73c0a45b01e6473714e0d5f759c061825
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77175
Reviewed-by: Dinesh Gehlot <digehlot@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
|
|
This patch introduces a CSE firmware specific data in order
to store Intel CSE and associated firmware related information which
requires a sync between Pre-RAM and Post-RAM phase.
This information will be used further to retrieve currently running
CSE RW firmware instead of fetching the version information by sending
a HECI cmd (which consumes 7ms-15ms depending upon the CSE operational
state).
Current implementation attempts to simply the CSE RW FW version store
and retrieval operations as below
* CSE sync in romstage (aka Pre-RAM) - Relying on .bss segment to store
the CSE info data in absence of real physical memory and sync back into
the CBMEM once available (after FSP-M exits).
* CSE sync in ramstage (aka Post-RAM) - Directly stored the CSE RW
version into the CBMEM (as CBMEM is online).
BUG=b:285405031
TEST=Able to build and boot google/rex. Verified CSE RW FW version
(for LITE SKU) is getting displayed without impacting the boot time.
w/o this patch:
10:start of ramstage 722,257 (43)
17:starting LZ4 decompress (ignore for x86) 723,777 (1,520)
w/ this patch:
10:start of ramstage 722,257 (43)
17:starting LZ4 decompress (ignore for x86) 723,777 (1,520)
Change-Id: Ia873af512851a682cf1fac0e128d842562a316ab
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77174
Reviewed-by: Julius Werner <jwerner@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
|
|
This UPD does exist for Alder Lake, so set it there also.
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Change-Id: If2f405804ab675aaf6dbf8b12d149566055b9eef
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77125
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
|
|
This patch adds the ability to show a pre-boot splash screen on
Meteor Lake systems using FSP-S.
The patch calls into `fsp_convert_bmp_to_gop_blt()` when the
`BMP_LOGO` config is enabled. This function converts a BMP
file to a BLT buffer, which is then used by FSP-S to render the splash
screen.
Additionally, increase the heap size (malloc'able size) upto 512KB
(when BMP_LOGO config is enabled) to accommodate high
resolution logo file.
BUG=b:284799726
TEST=Able to see splash screen while booting google/marasov
with BMP_LOGO config enable.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I9f4d1bc0aa991e784624ca19ba96a259ab8ddfa6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77233
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
This patch selects LZ4 decompression for logo CBFS file. Able to save
2ms of the boot time when HAVE_FSP_LOGO_SUPPORT config is enabled.
However, the compressed BMP logo size is increased by ~2KB.
Raw BMP Image size is ~97KB.
BUG=b:284799726
TEST=Able to see pre-boot splash screen while booting google/rex
with 32MB (W25Q256JWEIM) SPI-Flash.
w/o this patch:
sudo cbfstool image-screebo4es.bin print -r FW_MAIN_A
FMAP REGION: FW_MAIN_A
Name Offset Type Size Comp
...
...
logo.bmp 0x167480 raw 6172 LZMA (97078 decompressed)
...
15:starting LZMA decompress (ignore for x86) 849,090 (1,022)
16:finished LZMA decompress (ignore for x86) 851,207 (2,116)
w/ this patch:
sudo cbfstool image-screebo4es.bin print -r FW_MAIN_A
FMAP REGION: FW_MAIN_A
Name Offset Type Size Comp
...
...
logo.bmp 0x167480 raw 8568 LZ4 (97078 decompressed)
...
17:starting LZ4 decompress (ignore for x86) 849,419 (1,279)
18:finished LZ4 decompress (ignore for x86) 849,559 (140)
Change-Id: I856c39146a5ec0faf44c1cd37fa7c0d7296bf673
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76930
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
Intel has rebranded ESE as ISSE (Intel Silicon Security Engine),so all
references to ESE is updated to ISSE in the current coreboot code.
BUG=None
TEST=Build all the variants based on Intel Meteor Lake SoC
Signed-off-by: Usha P <usha.p@intel.com>
Change-Id: I1f8785704706d56a35e94a0f3386bc551cd1f263
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77241
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
|
|
Change-Id: If26184058536590b70bbb03209913118307ff6c5
Signed-off-by: Michael Strosche <michael.strosche@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76830
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Early Chromebook generations stored the information about
USB port power control for S3/S5 sleepstates in GNVS, although
the configuration is static.
Reduce code duplication and react to ACPI S4 as if it was ACPI
S5 request.
Change-Id: I7e6f37a023b0e9317dcf0355dfa70e28d51cdad9
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74524
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
|
