summaryrefslogtreecommitdiff
path: root/src/soc/intel/cannonlake/include
AgeCommit message (Collapse)Author
2021-05-02soc/intel/cannonlake/include: Drop unused codeFelix Singer
`soc_vtd_resources` from the else-part is unused since Cannon Lake was removed. Thus, drop it and that if-else-condition. Change-Id: I21689d1eae6952a80c98096443e7506a1466c07e Signed-off-by: Felix Singer <felixsinger@posteo.net> Reviewed-on: https://review.coreboot.org/c/coreboot/+/52775 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Nico Huber <nico.h@gmx.de>
2021-04-18soc/intel/cnl and mainboards: Drop `cnl_configure_pads()`Furquan Shaikh
CB:31250 ("soc/intel/cannonlake: Configure GPIOs again after FSP-S is done") introduced a workaround in coreboot for `soc/intel/cannonlake` platforms to save and restore GPIO configuration performed by mainboard across call to FSP Silicon Init (FSP-S). This workaround was required because FSP-S was configuring GPIOs differently than mainboard resulting in boot and runtime issues because of misconfigured GPIOs. This issue has since been fixed in FSP (verified with FSP v1263 on hatch). However, there were still 4 boards in coreboot using `cnl_configure_pads()`. As part of RFC CB:50829, librem_cnl, clevo/cml-u and system76/lemp9 were tested to ensure that this workaround is no longer required. This change drops the workaround using `cnl_configure_pads()` and updates all mainboards to use `gpio_configure_pads()` instead. Signed-off-by: Furquan Shaikh <furquan@google.com> Tested-by: Angel Pons <th3fanbus@gmail.com> (Tested purism/librem_cnl) Tested-by: Michael Niewöhner <foss@mniewoehner.de> (Tested clevo/cml-u which is similar to system76/lemp9) Change-Id: I7a4facbf23fc81707cb111859600e641fde34fc4 Reviewed-on: https://review.coreboot.org/c/coreboot/+/52248 Reviewed-by: Patrick Georgi <pgeorgi@google.com> Reviewed-by: Angel Pons <th3fanbus@gmail.com> Reviewed-by: Michael Niewöhner <foss@mniewoehner.de> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2021-03-27soc/intel: Rename and move MISCCFG_GPIO_PM_CONFIG_BITS definition to soc/gpio.hSubrata Banik
Lists of changes: 1. Rename MISCCFG_ENABLE_GPIO_PM_CONFIG -> MISCCFG_GPIO_PM_CONFIG_BITS 2. Move MISCCFG_GPIO_PM_CONFIG_BITS definition from intelblock/gpio.h to soc/gpio.h. Refer to detailed description below to understand the motivation behind this change. An advanced GPIO PM capabilities has been introduced since CNP PCH, refer to 'include/intelblock/gpio.h' for detailed GPIO PM bit definitions. Now with TGP PCH, additional bits are defined in the MISCCFG register for GPIO PM control. This results in different SoCs supporting different number of bits. The bits defined in earlier platforms (CNL, CML, ICL) are present on TGL, JSL and ADL too. Hence, refactor the common GPIO code to keep the bit definitions in intelblock/gpio.h, but the definition of MISCCFG_GPIO_PM_CONFIG_BITS is moved to soc/gpio.h so that each SoC can provide this as per hardware support. TEST=On ADL, TGL and JSL platform. Without this CL : GPIO COMM 0 MISCCFG:0xC0 (Bit 6 and 7 enable) With this CL : GPIO COMM 0 MISCCFG: 0x00 (Bit 6 and 7 disable) Change-Id: Ie027cbd7b99b39752941384339a34f8995c10c94 Signed-off-by: Subrata Banik <subrata.banik@intel.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/51767 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Furquan Shaikh <furquan@google.com>
2021-03-20soc/intel: Drop unused `GPIO_NUM_GROUPS` macroAngel Pons
This macro is unused and its value is often wrong. Drop it. Change-Id: Id3cfaa4d2eef49eddc02833efbe14e0c5c816263 Signed-off-by: Angel Pons <th3fanbus@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/51662 Reviewed-by: Subrata Banik <subrata.banik@intel.com> Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org> Reviewed-by: Furquan Shaikh <furquan@google.com> Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2021-03-01soc/intel: Drop `bootblock_cpu_init()` functionAngel Pons
Just call `fast_spi_cache_bios_region()` directly instead. Change-Id: I99f6ed4cf1a5c49b078cfd05e357c2d4c26ade45 Signed-off-by: Angel Pons <th3fanbus@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/50952 Reviewed-by: Michael Niewöhner <foss@mniewoehner.de> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2021-03-01soc/intel/{skl,cnl}: Do not chain-include systemagent.hAngel Pons
Change-Id: I8f48765ad99dad49f9d94c45aa4af6aff2ed702c Signed-off-by: Angel Pons <th3fanbus@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/50950 Reviewed-by: Michael Niewöhner <foss@mniewoehner.de> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2021-03-01soc/intel: Drop `romstage_pch_init()` functionAngel Pons
It only calls `smbus_common_init()`, so just call that directly. Change-Id: I0237f52bb9b0503e83f5dbf31c4064bd0f5bae28 Signed-off-by: Angel Pons <th3fanbus@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/50947 Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org> Reviewed-by: Michael Niewöhner <foss@mniewoehner.de> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2021-03-01soc/intel: Factor out common smbus.hAngel Pons
Change-Id: I31bb406bd2cf371ee935aa31777307043b2ee61a Signed-off-by: Angel Pons <th3fanbus@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/50942 Reviewed-by: Michael Niewöhner <foss@mniewoehner.de> Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org> Reviewed-by: Arthur Heymans <arthur@aheymans.xyz> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2021-03-01soc/intel: Factor out common gpe.hAngel Pons
The definitions are identical across seven platforms. Unify them. Change-Id: I32bbd0777f8ca9d0362d210b43e0ba8dd0c8d79b Signed-off-by: Angel Pons <th3fanbus@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/50940 Reviewed-by: Michael Niewöhner <foss@mniewoehner.de> Reviewed-by: Arthur Heymans <arthur@aheymans.xyz> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2021-02-25soc/intel/{skl,cnl}: Uniformize romstage.h whitespaceAngel Pons
Change-Id: Ide0e33826dd237bcd13f00400bbc8a08255b4f62 Signed-off-by: Angel Pons <th3fanbus@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/50945 Reviewed-by: Michael Niewöhner <foss@mniewoehner.de> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2021-02-16soc/intel: Drop aliases on MMCONF_BASE_ADDRESSKyösti Mälkki
Change-Id: I5ba60c1d8c314d37b4ef71c4613e6e0629da8149 Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/50662 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Angel Pons <th3fanbus@gmail.com> Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
2021-01-24soc/intel/cnl: use Kconfig to determine PCH typeMichael Niewöhner
We already know the PCH type at build time, so there is no need to do runtime detection. Thus, use Kconfig and drop `get_pch_series()`. Change-Id: I470871af5f5954e91a8135fddf4a2297a514d740 Signed-off-by: Michael Niewöhner <foss@mniewoehner.de> Reviewed-on: https://review.coreboot.org/c/coreboot/+/49874 Reviewed-by: Nico Huber <nico.h@gmx.de> Reviewed-by: Angel Pons <th3fanbus@gmail.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2021-01-21soc/intel/cannonlake: Allow RP#1 usage for ClkSrcJeremy Soller
0 is converted to not used, so use a special value to allow using PCIe root port #1. Change-Id: I2d64afc9bb4627913492edad8f36566e7fb18166 Signed-off-by: Jeremy Soller <jeremy@system76.com> Signed-off-by: Tim Crawford <tcrawford@system76.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/49172 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Patrick Rudolph <siro@das-labor.org>
2021-01-11soc/intel/cnl: add SLP_S0 residency register and enable LPIT supportMichael Niewöhner
Test: Linux adds the cpuidle sysfs interface; Windows with s0ix_enable=1 boots without crashing with an INTERNAL_POWER_ERROR. - Windows and Linux tested on google/akemi - Linux tested on clevo/cml-u Change-Id: I51fdf52419aa7f059b70a906fd8bdac88d5b6046 Tested-By: Matt DeVillier <matt.devillier@gmail.com> Tested-by: Michael Niewöhner <foss@mniewoehner.de> Signed-off-by: Michael Niewöhner <foss@mniewoehner.de> Reviewed-on: https://review.coreboot.org/c/coreboot/+/49046 Reviewed-by: Lance Zhao Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-12-17soc/intel/cannonlake: Change mainboard_silicon_init_params argumentPatrick Rudolph
Use FSPS_UPD instead of FSP_S_CONFIG as argument as already done on xeon_sp and denverton_ns. This allows to set test config UPDs from mainboard code as well. Change-Id: I6d67264e22df32b9210ce88b99d6a7a4f6b97ffb Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/48644 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Angel Pons <th3fanbus@gmail.com> Reviewed-by: Matt DeVillier <matt.devillier@gmail.com> Reviewed-by: Felix Singer <felixsinger@posteo.net>
2020-12-04soc/intel/{skl,cnl}: add NMI_{EN,STS} registersMichael Niewöhner
Add NMI_EN and NMI_STS registers, so they can be configured for using NMI gpios. References: - CMP-LP: Intel doc# 615146-1.2 - CMP-H: Intel doc# 620855-002 - SPT-H: Intel doc# 332691-003 - SPT-LP: Intel doc# 334659-005 - CNP-H: Intel doc# 337868-002 Test: trigger NMI via gpio on Supermicro X11SSM-F did not work before but now makes the Linux kernel complain about a NMI. Signed-off-by: Michael Niewöhner <foss@mniewoehner.de> Change-Id: I4d57ae89423bdaacf84f0bb0282bbb1c9df94598 Reviewed-on: https://review.coreboot.org/c/coreboot/+/48091 Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-10-24{cpu,soc}/intel: deduplicate cpu codeMichael Niewöhner
Move a whole bunch of copy-pasta code from soc/intel/{bdw,skl,cnl,icl, tgl,ehl,jsl,adl} and cpu/intel/{hsw,model_*} to cpu/intel/common. This change just moves the code. Rework is done in CB:46588. Change-Id: Ib0cc834de8492d59c423317598e1c11847a0b1ab Signed-off-by: Michael Niewöhner <foss@mniewoehner.de> Reviewed-on: https://review.coreboot.org/c/coreboot/+/46274 Reviewed-by: Felix Singer <felixsinger@posteo.net> Reviewed-by: Nico Huber <nico.h@gmx.de> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-10-21soc/intel: convert XTAL frequency constant to KconfigMichael Niewöhner
This converts the constant for the XTAL frequency to a Kconfig option. Change-Id: I1382dd274eeb9cb748f94c34f5d9a83880624c18 Signed-off-by: Michael Niewöhner <foss@mniewoehner.de> Reviewed-on: https://review.coreboot.org/c/coreboot/+/46018 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Nico Huber <nico.h@gmx.de>
2020-10-05soc: move mainboard_get_dram_part_num prototype to memory_info.hNick Vaccaro
BUG=b:169774661, b:168724473 TEST="emerge-volteer coreboot && emerge-nocturne coreboot && emerge-dedede coreboot" and verify they build successfully. Change-Id: I8b228475621ca1035fe13f8311355fc3b926e897 Signed-off-by: Nick Vaccaro <nvaccaro@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/45879 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Furquan Shaikh <furquan@google.com>
2020-10-05mb, soc: change mainboard_get_dram_part_num() prototypeNick Vaccaro
Change mainboard_get_dram_part_num() to return a constant character pointer to a null-terminated C string and to take no input parameters. This also addresses the issue that different SOCs and motherboards were using different definitions for mainboard_get_dram_part_num by consolidating to a single definition. BUG=b:169774661, b:168724473 TEST="emerge-volteer coreboot && emerge-dedede coreboot && emerge-hatch coreboot" and verify build completes successfully. Change-Id: Ie7664eab65a2b9e25b7853bf68baf2525b040487 Signed-off-by: Nick Vaccaro <nvaccaro@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/45873 Reviewed-by: Furquan Shaikh <furquan@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-10-03soc/intel: Make use of PMC low power program from common blockSubrata Banik
List of changes: 1. Select PMC_LOW_POWER_MODE_PROGRAM from applicable SoC directory 2. Remove redundant PMC programming from SoC and refer to common code block 3. Remove unused 'reg8' and 'reg32' variable as applicable from SoC function. Change-Id: I18894c49cfc6e88675b5fb71bca0412e5639fb4b Signed-off-by: Subrata Banik <subrata.banik@intel.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/45796 Reviewed-by: Angel Pons <th3fanbus@gmail.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-09-27soc/intel/cannonlake: Align gpio_op.asl with TGLSubrata Banik
Also drop gpio_common.h in favor of intelblocks/gpio_defs.h macros. TEST=Able to build and boot CNL and CML platform. 1) Dump and disassemble DSDT, verify unified methods like GRXS, GTXS etc. are there. 2) Verify no ACPI error seen while running 'dmesg' from console. 3) abuild --timeless to ensure there are no other functional changes. Change-Id: I78d712eeba56b9c098dc6a6f11e4e51cb2529b10 Signed-off-by: Subrata Banik <subrata.banik@intel.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/45654 Reviewed-by: Furquan Shaikh <furquan@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-09-21src/soc/intel: Drop unneeded empty linesElyes HAOUAS
Change-Id: Id93aab5630e928ee4d7e957801e15a4cc8739fae Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr> Reviewed-on: https://review.coreboot.org/c/coreboot/+/44594 Reviewed-by: Michael Niewöhner <foss@mniewoehner.de> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-09-17soc/intel/cannonlake: add missing special function padsMichael Niewöhner
The following parameters do nothing else than configuring the corresponding pads to native mode: - DdiPortEdp - DdiPort*Hpd - DdiPort*Ddc - GpioDdp* - SpiGpioAssign - I2c*GpioAssign - SerialIoUartDebugEnable - Gp*GpioAssign - Uart*GpioAssign - GpioEnableHdaLink - AudioLinkDmic* - AudioLinkSsp* - GpioEnableHdaSspMasterClock - AudioLinkSndw* - SmbAlertEnable Add the missing special function gpio pad groups for CNL, to be able to configure them via gpio.h instead having to set various FSP parameters. The groups and names are documented in the PCH EDS, in Linux (linux/drivers/pinctrl/intel/pinctrl-cannonlake.c) and other places. Also, see soc/intel/tigerlake for reference. Change-Id: Ia3bc1df1a14dbca7c7213577cb2d5b98bb0acf64 Signed-off-by: Michael Niewöhner <foss@mniewoehner.de> Reviewed-on: https://review.coreboot.org/c/coreboot/+/45211 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Subrata Banik <subrata.banik@intel.com>
2020-09-17soc/intel/cannonlake: rename "RSVD" GPIOs to their correct namesMichael Niewöhner
The names of the GPIO_RSVD_* are documented in the PCH EDS, in Linux (linux/drivers/pinctrl/intel/pinctrl-cannonlake.c) and other places. Also, see soc/intel/tigerlake for reference. Change-Id: I59df09c8fd464e75f918455aa1972765abc51459 Signed-off-by: Michael Niewöhner <foss@mniewoehner.de> Reviewed-on: https://review.coreboot.org/c/coreboot/+/45210 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Subrata Banik <subrata.banik@intel.com>
2020-09-09soc/intel/cannonlake: Add PCIe ports on PCH-HPatrick Rudolph
Fixes complains about missing INT configuration by the pciexp kernel modules. Tested with Linux 5.5 on Prodrive Hermes. Change-Id: I277f592cd8d2c86a9c7ba4b34d3f703f7d593582 Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/45065 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Angel Pons <th3fanbus@gmail.com>
2020-07-20soc/intel/cannonlake: Add configs for USB 3.1 Gen2 EV settingsJamie Chen
Add configs for USB 3.1 Gen2 EV settings so that people can set the EV settings per board in device tree. BUG=b:150515720 BRANCH=none TEST=build coreboot and fsp with enabled fw_debug. Flashed to puff and checked the log. All usb configs were set correctly. Signed-off-by: Jamie Chen <jamie.chen@intel.com> Change-Id: Id4860665619095139c329565d433d9eb495cac02 Reviewed-on: https://review.coreboot.org/c/coreboot/+/39448 Reviewed-by: Edward O'Callaghan <quasisec@chromium.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-07-14src: Remove unused 'include <stdint.h>Elyes HAOUAS
Found using: diff <(git grep -l '#include <stdint.h>' -- src/) <(git grep -l 'int8_t\|int16_t\|int32_t\|int64_t\|intptr_t\|intmax_t\|s8\|u8\|s16\|u16\|s32\|u32\|s64\|u64\|INT8_MIN\|INT8_MAX\|INT16_MIN\|INT16_MAX\|INT32_MIN\|INT32_MAX\|INT64_MIN\|INT64_MAX\|INTMAX_MIN\|INTMAX_MAX' -- src/) |grep -v vendorcode |grep '<' Change-Id: I5e14bf4887c7d2644a64f4d58c6d8763eb74d2ed Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr> Reviewed-on: https://review.coreboot.org/c/coreboot/+/41827 Reviewed-by: Patrick Georgi <pgeorgi@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-06-25soc/intel/cannonlake: Add missing USB_PORT_WAKE_ENABLE defineEdward O'Callaghan
Align support for enable wake-on-usb attach/detach as was introduced in Skylake in `commit 3bfe3404df32ca226c624be0435c640bf1ebeae7`. BUG=b:159187889 BRANCH=none TEST=none Change-Id: Ie63e4f1fcdea130f8faed5c0d34a6a96759946b6 Signed-off-by: Edward O'Callaghan <quasisec@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/42716 Reviewed-by: Sam McNally <sammc@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-05-26cannonlake: update processor power limits configurationSumeet R Pawnikar
Update processor power limit configuration parameters based on common code base support for Intel Cannonlake SoC based platforms. BRANCH=None BUG=None TEST=Built and tested on drallion system Change-Id: Iac6e6f81343fcd769619e9d7ac339430966834f6 Signed-off-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/41235 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
2020-05-14soc/intel: Drop ABOVE_4GB_MEM_BASE_SIZE and use cpu_phys_address_size()Furquan Shaikh
This change uses cpu_phys_address_size() to calculate the size of high MMIO region instead of a macro for each SoC. This ensures that the entire range above TOUUD that can be addressed by the CPU is used for MMIO above 4G boundary. Change-Id: I01a1a86c0c65856f9f35185c2f233c58f18f5dfe Signed-off-by: Furquan Shaikh <furquan@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/41347 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2020-05-14soc/intel/common/block/systemagent: Use TOUUD as base for MMIO above 4GFurquan Shaikh
This change sets the base for MMIO above 4G to TOUDD. It matches what is used by resource allocator if MMIO resources are allocated above 4G and also matches the expectation in northbridge.asl. This change also gets rid of the macro ABOVE_4GB_MEM_BASE_ADDRESS since it is now unused. BUG=b:149186922 TEST=Verified that kernel does not complain about MMIO windows above 4G. Signed-off-by: Furquan Shaikh <furquan@google.com> Change-Id: Ibbbfbdad867735a43cf57c256bf206a3f040f383 Reviewed-on: https://review.coreboot.org/c/coreboot/+/41155 Reviewed-by: Aaron Durbin <adurbin@chromium.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-05-11treewide: Remove "this file is part of" linesPatrick Georgi
Stefan thinks they don't add value. Command used: sed -i -e '/file is part of /d' $(git grep "file is part of " |egrep ":( */\*.*\*/\$|#|;#|-- | *\* )" | cut -d: -f1 |grep -v crossgcc |grep -v gcov | grep -v /elf.h |grep -v nvramtool) The exceptions are for: - crossgcc (patch file) - gcov (imported from gcc) - elf.h (imported from GNU's libc) - nvramtool (more complicated header) The removed lines are: - fmt.Fprintln(f, "/* This file is part of the coreboot project. */") -# This file is part of a set of unofficial pre-commit hooks available -/* This file is part of coreboot */ -# This file is part of msrtool. -/* This file is part of msrtool. */ - * This file is part of ncurses, designed to be appended after curses.h.in -/* This file is part of pgtblgen. */ - * This file is part of the coreboot project. - /* This file is part of the coreboot project. */ -# This file is part of the coreboot project. -# This file is part of the coreboot project. -## This file is part of the coreboot project. --- This file is part of the coreboot project. -/* This file is part of the coreboot project */ -/* This file is part of the coreboot project. */ -;## This file is part of the coreboot project. -# This file is part of the coreboot project. It originated in the - * This file is part of the coreinfo project. -## This file is part of the coreinfo project. - * This file is part of the depthcharge project. -/* This file is part of the depthcharge project. */ -/* This file is part of the ectool project. */ - * This file is part of the GNU C Library. - * This file is part of the libpayload project. -## This file is part of the libpayload project. -/* This file is part of the Linux kernel. */ -## This file is part of the superiotool project. -/* This file is part of the superiotool project */ -/* This file is part of uio_usbdebug */ Change-Id: I82d872b3b337388c93d5f5bf704e9ee9e53ab3a9 Signed-off-by: Patrick Georgi <pgeorgi@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/41194 Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-05-06treewide: replace GPLv2 long form headers with SPDX headerPatrick Georgi
This replaces GPLv2-or-later and GPLv2-only long form text with the short SPDX identifiers. Commands used: perl -i -p0e 's|/\*[*\n\t ]*This program is free software[:;].*you.*can.*redistribute.*it.*and/or.*modify.*it.*under.*the.*terms.*of.*the.*GNU.*General.*Public.*License.*as.*published.*by.*the.*Free.*Software.*Foundation[;,].*version.*2.*of.*the.*License.*or.*(at.*your.*option).*any.*later.*version.+This.*program.*is.*distributed.*in.*the.*hope.*that.*it.*will.*be.*useful,.*but.*;.*without.*even.*the.*implied.*warranty.*of.*MERCHANTABILITY.*or.*FITNESS.*FOR.*A.*PARTICULAR.*PURPOSE..*.*See.*the.*GNU.*General.*Public.*License for more details.[\n\t ]*\*/|/* SPDX-License-Identifier: GPL-2.0-or-later */|s' $(cat filelist) perl -i -p0e 's|/\*[*\n\t ]*This program is free software[:;].*you.*can.*redistribute.*it.*and/or.*modify.*it.*under.*the.*terms.*of.*the.*GNU.*General.*Public.*License.*as.*published.*by.*the.*Free.*Software.*Foundation[;,].*version.*2.+This.*program.*is.*distributed.*in.*the.*hope.*that.*it.*will.*be.*useful,.*but.*;.*without.*even.*the.*implied.*warranty.*of.*MERCHANTABILITY.*or.*FITNESS.*FOR.*A.*PARTICULAR.*PURPOSE..*.*See.*the.*GNU.*General.*Public.*License for more details.[\n\t ]*\*/|/* SPDX-License-Identifier: GPL-2.0-only */|s' $(cat filelist) perl -i -p0e 's|/\*[*\n\t ]*This program is free software[:;].*you.*can.*redistribute.*it.*and/or.*modify.*it.*under.*the.*terms.*of.*the.*GNU.*General.*Public.*License.*version.*2.*as.*published.*by.*the.*Free.*Software.*Foundation[.;,].+This.*program.*is.*distributed.*in.*the.*hope.*that.*it.*will.*be.*useful,.*but.*;.*without.*even.*the.*implied.*warranty.*of.*MERCHANTABILITY.*or.*FITNESS.*FOR.*A.*PARTICULAR.*PURPOSE..*.*See.*the.*GNU.*General.*Public.*License for more details.[\n\t ]*\*/|/* SPDX-License-Identifier: GPL-2.0-only */|s' $(cat filelist) perl -i -p0e 's|/\*[*\n\t ]*This software is licensed under.*the.*terms.*of.*the.*GNU.*General.*Public.*License.*version.*2.*as.*published.*by.*the.*Free.*Software.*Foundation,.+This.*program.*is.*distributed.*in.*the.*hope.*that.*it.*will.*be.*useful,.*but.*;.*without.*even.*the.*implied.*warranty.*of.*MERCHANTABILITY.*or.*FITNESS.*FOR.*A.*PARTICULAR.*PURPOSE..*.*See.*the.*GNU.*General.*Public.*License for more details.[\n\t ]*\*/|/* SPDX-License-Identifier: GPL-2.0-only */|s' $(cat filelist) Change-Id: I7a746088a35633c11fc7ebe86006e96458a1abf8 Signed-off-by: Patrick Georgi <pgeorgi@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/41066 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: David Hendricks <david.hendricks@gmail.com> Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
2020-05-06treewide: Move "is part of the coreboot project" line in its own commentPatrick Georgi
That makes it easier to identify "license only" headers (because they are now license only) Script line used for that: perl -i -p0e 's|/\*.*\n.*This file is part of the coreboot project.*\n.*\*|/* This file is part of the coreboot project. */\n/*|' # ...filelist... Change-Id: I2280b19972e37c36d8c67a67e0320296567fa4f6 Signed-off-by: Patrick Georgi <pgeorgi@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/41065 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: David Hendricks <david.hendricks@gmail.com> Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Angel Pons <th3fanbus@gmail.com>
2020-05-02acpi: Move ACPI table support out of arch/x86 (3/5)Furquan Shaikh
This change moves all ACPI table support in coreboot currently living under arch/x86 into common code to make it architecture independent. ACPI table generation is not really tied to any architecture and hence it makes sense to move this to its own directory. In order to make it easier to review, this change is being split into multiple CLs. This is change 3/5 which basically is generated by running the following command: $ git grep -iIl "arch/acpi" | xargs sed -i 's/arch\/acpi/acpi\/acpi/g' BUG=b:155428745 Change-Id: I16b1c45d954d6440fb9db1d3710063a47b582eae Signed-off-by: Furquan Shaikh <furquan@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/40938 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
2020-04-06soc/intel/cannonlake: Use SPDX for GPL-2.0-only filesAngel Pons
Done with sed and God Lines. Only done for C-like code for now. Change-Id: I48422453735d50eb9292f39a3c031073d647a17c Signed-off-by: Angel Pons <th3fanbus@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/40212 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Felix Singer <felixsinger@posteo.net>
2020-03-18soc: Remove copyright noticesPatrick Georgi
They're listed in AUTHORS and often incorrect anyway, for example: - What's a "Copyright $year-present"? - Which incarnation of Google (Inc, LLC, ...) is the current copyright holder? - People sometimes have their editor auto-add themselves to files even though they only deleted stuff - Or they let the editor automatically update the copyright year, because why not? - Who is the copyright holder "The coreboot project Authors"? - Or "Generated Code"? Sidestep all these issues by simply not putting these notices in individual files, let's list all copyright holders in AUTHORS instead and use the git history to deal with the rest. Change-Id: I4c110f60b764c97fab2a29f6f04680196f156da5 Signed-off-by: Patrick Georgi <pgeorgi@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/39610 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Angel Pons <th3fanbus@gmail.com> Reviewed-by: David Hendricks <david.hendricks@gmail.com>
2020-03-07intel/soc: skl,apl,cnl,icl,tgl: add INTRUDER relevant registersMichael Niewöhner
Add registers that are relevant for the case intrusion detection functionality. Intel documents: 332691-003EN, 335193-006, 341081-001, ... Change-Id: If12d21e8e6721abb877cbbfbbba8f0127a86d96b Signed-off-by: Michael Niewöhner <foss@mniewoehner.de> Reviewed-on: https://review.coreboot.org/c/coreboot/+/39263 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2020-03-07intel/soc: skl,apl,cnl,icl,tgl,common: enable TCO SMIs if selectedMichael Niewöhner
Enable TCO SMIs in common code, if selected by Kconfig. This is needed for the follow-up commits regarding INTRUDER interrupt. Tested on X11SSM-F. Change-Id: If63effe74ac59b5d051a6454bc6375bb89605215 Signed-off-by: Michael Niewöhner <foss@mniewoehner.de> Reviewed-on: https://review.coreboot.org/c/coreboot/+/39262 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2020-02-25soc/intel/cannonlake: Add TDC config for CMLMarx Wang
Add Thermal Design Current (TDC) defaults for CML: 1. TdcEnable 2. TdcPowerLimit BUG=b:148912093 BRANCH=None TEST=build coreboot and Intel FSP with fw_debug enabled, flash image to the device, capture the log from the serial port during boot-up and check TdcEnable and TdcPowerLimit for each domain in captured log Signed-off-by: Marx Wang <marx.wang@intel.com> Change-Id: Ie4b17e5b4ce41c1adb436ae5646f0d8578a440e8 Reviewed-on: https://review.coreboot.org/c/coreboot/+/38741 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com> Reviewed-by: John Su <john_su@compal.corp-partner.google.com> Reviewed-by: Angel Pons <th3fanbus@gmail.com>
2020-02-17src/intel: Define HFSTS3 registerSridhar Siricilla
Changes: 1. Define HFSTS3 register across SoCs(apl/cnl/icl/tgl). 2. Define cse_is_hfs3_fw_sku_custom() which checks ME's Firmware SKU is Custom or not. TEST=Verified on hatch, soraka, bobba and iclrvp. Change-Id: I4188e58a4a08d87be2d84674e00ed1407fb8bf82 Signed-off-by: Sridhar Siricilla <sridhar.siricilla@intel.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/38798 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
2020-02-09soc/intel/{common,skl,cnl,icl,apl,tgl}: Move HFSTS1 register definition to SoCSridhar Siricilla
Below changes are implemented: 1. Move HFSTS1 register definition to SoC since HFSTS1 register definition is specific to a SoC. Moving structure back to SoC specific to avoid unnecessay SoC specific macros in the common code. 2. Define a set of APIs in common code since CSE operation modes and working states are same across SoCs. cse_is_hfs1_com_normal(void) cse_is_hfs1_com_secover_mei_msg(void) cse_is_hfs1_com_soft_temp_disable(void) cse_is_hfs1_cws_normal(void) 3. Modify existing code to use callbacks to get data of me_hfs1 structure. TEST=Build and Boot hatch, soraka, tglrvp, bobba and iclrvp boards. Change-Id: If7ea6043d7b5473d0c16e83d7b2d4b620c125652 Signed-off-by: Sridhar Siricilla <sridhar.siricilla@intel.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/35546 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Furquan Shaikh <furquan@google.com>
2020-02-04soc/intel: Add get_pmbaseEugene Myers
Originally a part of security/intel/stm. Add get_pmbase to the intel platform setup code. get_pmbase is used by the coreboot STM setup functions to ensure that the pmbase is accessable by the SMI handler during runtime. The pmbase has to be accounted for in the BIOS resource list so that the SMI handler is allowed this access. Change-Id: If6f6295c5eba9eb20e57ab56e7f965c8879e93d2 Signed-off-by: Eugene D. Myers <edmyers@tycho.nsa.gov> Reviewed-on: https://review.coreboot.org/c/coreboot/+/37990 Reviewed-by: Patrick Georgi <pgeorgi@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-02-04soc/intel/cannonlake: Allow Audio DSP OSC qualification for low power idleAamir Bohra
With Audio DSP OSC qualification disabled from S0ix criteria. S0ix is achieved before the DSP is suspended. When driver tries to suspend DSP its already turned off. BUG=b:139481313 Change-Id: I20b793b95483af03ce4ae068ac07864a9e90d39b Signed-off-by: Aamir Bohra <aamir.bohra@intel.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/37604 Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org> Reviewed-by: Furquan Shaikh <furquan@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-01-18soc/intel/cannonlake: Add chip config for SATA strengthJamie Chen
Add config to chip.h for tuning SATA gen3 strength. BUG=b:147351936 BRANCH=none TEST=build successful in puff Change-Id: I4dcd23834fa3c01c1d88697a7bb8cf361709b62e Signed-off-by: Jamie Chen <jamie.chen@intel.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/38432 Reviewed-by: Edward O'Callaghan <quasisec@chromium.org> Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-01-10soc/intel/{apl,cnl,icl,skl,tgl}: Make above 4GB MMIO resource properSubrata Banik
This patch ensures coreboot is not publishing above 4GB mmio resource if soc common config "enable_above_4GB_mmio" not enable. Publishing unnecessary 4GB above MMIO resource with wrong base and size is causing problem while working with discrete GPU. Unable to boot with dGPU on IA platform with below error: [ 2.297425] pcieport 0000:00:1c.0: PCI bridge to [bus 05] [ 2.302858] pcieport 0000:00:1c.0: bridge window [io 0x2000-0x2fff] [ 2.309427] pcieport 0000:00:1c.0: bridge window [mem 0xb2000000-0xb20fffff] [ 2.316679] pcieport 0000:00:1c.0: bridge window [mem 0x840000000-0x8c01fffff 64bit pref] [ 2.325072] pcieport 0000:00:1c.0: PCI bridge to [bus 05] [ 2.330502] pcieport 0000:00:1c.0: bridge window [io 0x2000-0x2fff] [ 2.337062] pcieport 0000:00:1c.0: bridge window [mem 0xb2000000-0xb20fffff] [ 2.344317] pcieport 0000:00:1c.0: bridge window [mem 0xa0000000-0xb01fffff 64bit pref] [ 2.352541] [drm] Not enough PCI address space for a large BAR. Change-Id: I77b3a0e44582b047d7fbe679d3000d616f7e6111 Signed-off-by: Subrata Banik <subrata.banik@intel.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/38125 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com> Reviewed-by: Pratikkumar V Prajapati <pratikkumar.v.prajapati@intel.com>
2020-01-09sb/intel/common: Add smbus_set_slave_addr()Kyösti Mälkki
Change-Id: I7dddb61fab00e0f4f67d4eebee0cfe8dcd99f4ab Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/38230 Reviewed-by: Angel Pons <th3fanbus@gmail.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-01-06soc/intel/cannonlake: Add VR config for CFL, CNL and WHLPatrick Rudolph
Add VR config IccMax, DC and AC loadline defaults and voltage regulator maximum for all CFL, CNL and WHL. This supports mainboards with replaceable CPUs and provides sane defaults for boards that are missing the devicetree overwrite. Remove the default IccMax to make use of the introduced lookup-table. Also change some hex values to decimal. I couldn't find CML datasheet, so those are left out for now. Used Doc #337344 and #338023 Section 7. Change-Id: I1d2e174157d468830cc0baf2a2d8295ef61a1a63 Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/37466 Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2019-12-26soc/intel/cannonlake: Refactor pch_early_init() codeUsha P
This patch keeps required pch_early_init() function like ABASE programming, GPE and RTC init into bootblock and moves remaining functions like TCO configuration and SMBus init into romstage/pch.c in order to maintain only required chipset programming for bootblock and verstage. Rename the pch_init function to bootblock_pch_init and romstage_pch_init according to the stage it is defined in. TEST=Able to build and boot hatch successfully. Change-Id: Idf7b04edc3fce147f7857561ce7d5b0cd05f43fe Signed-off-by: Usha P <usha.p@intel.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/37308 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Subrata Banik <subrata.banik@intel.com>
2019-12-03soc/intel/cannonlake: Configure GPIO PM configuration in bootblockSubrata Banik
This patch performs below operations: 1. Rename soc_fill_gpio_pm_configuration to soc_gpio_pm_configuration 2. Move soc_gpio_pm_configuration() to gpio_common.c 3. Calling from bootblock and after FSP-S to ensure GPIO PM configuration is updated with devicetree.cb value even with platform reset. BUG=b:144002424 TEST=coreboot configures all MISCCFG.bit 0-5 local clock gating based on devicetree.cb Change-Id: I54061d556d62462d9012bc47bb9f3604a3e5a250 Signed-off-by: Subrata Banik <subrata.banik@intel.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/37319 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Furquan Shaikh <furquan@google.com>
2019-11-22intel/smm: Provide common smm_relocation_paramsKyösti Mälkki
Pull in all copies of smm_relocation_params structs defined for intel platforms. Pull in all the inlined MSR accessors to the header file. Change-Id: I39c6cffee95433aea1a3c783b869eedfff094413 Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/34840 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2019-11-10soc/intel/common/ebda: Drop codeArthur Heymans
There is no need to use EBDA to pass cbmem_top from romstage to later stages. Change-Id: I46e2459ff3c785f530cabc5930004ef920ffc89a Signed-off-by: Arthur Heymans <arthur@aheymans.xyz> Reviewed-on: https://review.coreboot.org/c/coreboot/+/36362 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Michael Niewöhner Reviewed-by: Nico Huber <nico.h@gmx.de>
2019-11-04soc/intel: skl,cnl,icl: rely on TOLUM as cbmem_top returned by FSPMichael Niewöhner
Instead of doing our own calculations, rely on TOLUM returned by FSP for cbmem_top. This (hopefully) saves us from making mistakes in weird calculations of offsets and alignments. Further this makes it easier to implement e.g. SGX PRMRR size selection via Kconfig as we do not have to make any assumptions about alignments but can simply pass (valid) values to FSP. Tested successfully on X11SSM-F Change-Id: If66a00d1320917bc68afb32c19db0e24c6732812 Signed-off-by: Michael Niewöhner <foss@mniewoehner.de> Reviewed-on: https://review.coreboot.org/c/coreboot/+/36136 Reviewed-by: Arthur Heymans <arthur@aheymans.xyz> Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Nico Huber <nico.h@gmx.de> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2019-11-01soc/intel/{cnl,icl}: Move globalnvs.asl/nvs.h into common/block/Subrata Banik
This patch creates a common instance of globalnvs.asl/nvs.h inside intel common code (soc/intel/common/block/) and ask cnl & icl soc code to refer globalnvs.asl and nvs.h from common code block. TEST=Able to build and boot Hatch and ICL DE system. Dump DSDT.asl to verify GNVS operation region presence after booting to OS. Change-Id: Ia9fb12a75557bd7dc38f6d22ba2b32065d18b3ee Signed-off-by: Subrata Banik <subrata.banik@intel.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/36457 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Arthur Heymans <arthur@aheymans.xyz> Reviewed-by: Michael Niewöhner Reviewed-by: Angel Pons <th3fanbus@gmail.com>
2019-10-21Revert "soc/intel/cannonlake: Remove DMA support for PTT"Jeremy Soller
This reverts commit d5018a8f78b9e1f0b7d3d1be298cba9716b10c6c. Reason for revert: Breaks boot on Whiskey Lake-U boards Both System76 and Purism have had memory initialization failures when this patch is applied, with the following error message: Failed to accommodate FSP reserved memory request! An extra 4096 bytes needs to be reserved for the FSP on these systems, and reinstating the PTT reservation does this as expected. PTT is enabled for the System76 galp3-c in the ME configuration, which is why the behaviour is different. Signed-off-by: Jeremy Soller <jeremy@system76.com> CC: Matt DeVillier <matt.devillier@gmail.com> CC: Subrata Banik <subrata.banik@intel.com> Change-Id: Ib82f02c4a2b1cd2dbf95d4ca4a9edd314e78edd2 Reviewed-on: https://review.coreboot.org/c/coreboot/+/35924 Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Lance Zhao <lance.zhao@gmail.com> Reviewed-by: Michael Niewöhner Reviewed-by: Patrick Rudolph <siro@das-labor.org> Reviewed-by: Matt DeVillier <matt.devillier@gmail.com> Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2019-08-15intel/smm: Define struct ied_header just onceKyösti Mälkki
Change-Id: I6fc083aa30d05c11c1b6db7b3facacf5ae857c92 Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/34855 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Angel Pons <th3fanbus@gmail.com>
2019-08-15soc/intel: Rename some SMM support functionsKyösti Mälkki
Rename southbridge_smm_X to smm_southbridge_X. Rename most southcluster_smm_X to smm_southbridge_X. Change-Id: I4f6f9207ba32cf51d75b9ca9230e38310a33a311 Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/34856 Reviewed-by: Aaron Durbin <adurbin@chromium.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2019-08-15intel/ice,sky,cannon: Drop unused EMRR and UNCORE_EMRR codeKyösti Mälkki
There was no code present to call wrmsr with the data we prepared in the structs. The MSRS are already set up by FSP, just reference with the more recent names of PRMRR and UNCORE_PRMRR. Change-Id: Ib49e7af52e1170a1304975ff0ae63f99e106dffe Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/34824 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Angel Pons <th3fanbus@gmail.com>
2019-08-15mainboard/google: Fix indirect includesKyösti Mälkki
Change-Id: Ie79702efab519b16cff45ccad61b95e7d8c2fbac Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/34854 Reviewed-by: Angel Pons <th3fanbus@gmail.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2019-08-09cpu/x86/smm: Drop SMI handler address from structKyösti Mälkki
Change-Id: Ib925b11ba269e0f3a9a0a7550705bf2a6794c5b1 Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/34747 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2019-08-08arch/x86: Change smm_subregion() prototypeKyösti Mälkki
Do this to avoid some amount of explicit typecasting that would be required otherwise. Change-Id: I5bc2c3c1dd579f7c6c3d3354c0691e4ba3c778e1 Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/34706 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
2019-08-07cpu/x86/smm: Promote smm_subregion()Kyösti Mälkki
No need to limit these declarations to FSP. Both PARALLEL_MP_INIT smm_relocate() and TSEG_STAGE_CACHE can be built on top of this. Change-Id: I7b0b9b8c8bee03aabe251c50c47dc42f6596e169 Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/34701 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
2019-07-25soc/intel: Guard remaining SA_DEV_ROOT definitionKyösti Mälkki
Prevent implicit cast to pointers. The compiler doesn't warn about the conversion from integer to pointer without a cast, because SA_DEV_ROOT is literally '0' and there seems to be an exception for that conversion. Change-Id: I64fc156e3b9f578414ad03a00edb7cf3e33205c1 Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/34544 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Nico Huber <nico.h@gmx.de>
2019-07-21soc/intel: Expand SA_DEV_ROOT for ramstageKyösti Mälkki
We do not want to disguise somewhat complex function calls as simple macros. Change-Id: I298f7f9a1c6a64cfba454e919eeaedc7bb2d4801 Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/34411 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Furquan Shaikh <furquan@google.com>
2019-07-17soc/intel: Fix regression with hidden PCI devicesKyösti Mälkki
Fix regression with commit 903b40a soc/intel: Replace uses of dev_find_slot() Platforms where FSP hides PCI devices before enumeration may halt with error message 'PCI: dev is NULL!'. The workaround here is to print an error message revealing the faulty source code function and revert to old behaviour of dev_find_slot(). Change-Id: I5eab3e7f1993b686103eaa257aacda379dc259fa Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/34285 Reviewed-by: Matt DeVillier <matt.devillier@gmail.com> Reviewed-by: Maxim Polyakov <max.senia.poliak@gmail.com> Reviewed-by: Angel Pons <th3fanbus@gmail.com> Reviewed-by: Christian Walter <christian.walter@9elements.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2019-07-13cpu/x86: Move smm_lock() prototypeKyösti Mälkki
The function implementations are in local platform scopes. Change-Id: I7a3025398b15fe6d2c5a13cdb65f3e62a49c0bc6 Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/34151 Reviewed-by: Angel Pons <th3fanbus@gmail.com> Reviewed-by: Furquan Shaikh <furquan@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2019-07-10soc/intel: Remove invalid smm_relocate stubsKyösti Mälkki
Remove the per-platform empty stubs, builds would just fail as there is no equivalent conditional for the smmrelocate.c file. Change-Id: Ie11f307b7bc5415bfdba6a2c66aed01b70d9f0e0 Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/34150 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Furquan Shaikh <furquan@google.com> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2019-07-07soc/intel/{cannonlake,icelake}: Do not define PCH_DEV_PMC in ramstageFurquan Shaikh
This change intentionally removes the definition of PCH_DEV_PMC from ramstage to avoid silent errors. This device gets hidden from PCI bus in FSP-S and hence dropped from the root bus by the resource allocator. In order to avoid incorrect references to the device, avoid defining it in ramstage where it known to return NULL. BUG=b:136861224 Change-Id: I4f69470ec80c7127a2b604ed2b1f794f5a63e126 Signed-off-by: Furquan Shaikh <furquan@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/34120 Reviewed-by: Subrata Banik <subrata.banik@intel.com> Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2019-07-07soc/intel/cannonlake, mb/google/sarien: Get rid of unused dev paramFurquan Shaikh
This change gets rid of unused dev param to pmc_set_afterg3. BUG=b:136861224 Change-Id: Ic197d6fb8618db15601096f5815e82efc2b539c1 Signed-off-by: Furquan Shaikh <furquan@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/34117 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com> Reviewed-by: Subrata Banik <subrata.banik@intel.com>
2019-07-05soc/intel/cannonlake: Fix PMC and GPIO block values for PCH-HJeremy Soller
Some of the values used for GPIO_CFG and MISCCFG were not correct, causing GPEs to not work correctly. This adjusts them according to the values found in the original ACPI tables for the System76 Gazelle. Unfortunately, the Intel documentation[1] mentioned below is also incorrect. I have mentioned this to Intel already. The source for the Intel CoffeeLake FSP also confirms these new numbers. This was tested on a System76 Gazelle (gaze14). The EC uses GPP_K3 for its GPE and GPP_K6 is used for the lid switch GPE. Both function correctly after applying this change. [1] Intel Document #572235: Intel ® 300 Series Chipset Families Platform Controller Hub External Design Specification (EDS) - Volume 2 of 2 Change-Id: I4ecc9552468037598ef5d4e10122d660dcbfe71d Signed-off-by: Jeremy Soller <jeremy@system76.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/33941 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Nico Huber <nico.h@gmx.de> Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
2019-07-04soc/intel: Replace uses of dev_find_slot()Kyösti Mälkki
To call dev_find_slot(0, xx) in romstage can produce invalid results since PCI bus enumeration has not been progressed yet. Replace this with method that relies on bus topology that walks the root bus only. Change-Id: I2883610059bb9fa860bba01179e7d5c58cae00e5 Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/33996 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
2019-06-03soc/intel: Replace UART_BASE() and friends with a KconfigNico Huber
Re-add the Kconfig CONSOLE_UART_BASE_ADDRESS. It was lost by accident on APL at least. It is used outside of soc/intel/ scope, e.g. to con- figure SeaBIOS. As we only ever configure a single UART for the coreboot console, we don't need different addresses for each possible UART. Which saves us a lot of code. Change-Id: I28e1d98aa37a6acb57b98b8882fc4fa131d5d309 Signed-off-by: Nico Huber <nico.h@gmx.de> Reviewed-on: https://review.coreboot.org/c/coreboot/+/33098 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Patrick Rudolph <siro@das-labor.org>
2019-05-28soc/intel/cannonlake: Dump ME status info before notify EndOfFirmwareBora Guvendik
Dumping ME status displays wrong information if we disable Heci1 because it is called after fsp notifies EndOfFirmware and disables Heci1. This patch moves the ME status dump before fsp notify EndOfFirmware. TEST=Boot to OS, check ME dump information Change-Id: Ifd8b18a41c502c4ecfb84698a7669028394589fd Signed-off-by: Bora Guvendik <bora.guvendik@intel.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/32991 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Subrata Banik <subrata.banik@intel.com> Reviewed-by: Furquan Shaikh <furquan@google.com> Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
2019-05-22soc/intel/cannonlake: Dump ME f/w version and status informationTim Wawrzynczak
At the end of device enable, print the ME f/w version number. Before resume or loading payload, dump the ME's Host Firmware Status registers. BUG=b:131437724 BRANCH=none TEST=Prints seemingly sane values on WHL and CML devices. Change-Id: Ibeb3a2a85cd84c9baa45f90f20a3dcf69f7d5646 Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org> Reviewed-on: https://review.coreboot.org/c/coreboot/+/32527 Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org> Reviewed-by: Furquan Shaikh <furquan@google.com> Reviewed-by: Subrata Banik <subrata.banik@intel.com> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2019-05-20soc/intel/cannonlake: Make use of gpio_pm_configure()Subrata Banik
Provide option in chip.h to set dynamic local clock gating setting. BUG=b:130764684 TEST=Able to build and boot CML. Change-Id: Iec60076398b745e11d5025e4d7a5c35374d918a4 Signed-off-by: Subrata Banik <subrata.banik@intel.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/32790 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Furquan Shaikh <furquan@google.com>
2019-05-15soc/intel/cannonlake: Support different SPD read type for each slotPhilip Chen
Also clean up cannonlake_memcfg_init. The major changes include: (1) Add enum 'mem_info_read_type' to spd_info. (2) Add per-dimm-slot spd_info to cnl_mb_cfg. (3) Setup memory config for each slot independently. (4) Squash meminit_memcfg_spd(). BUG=chromium:960581, b:124990009 BRANCH=none TEST=boot hatch, hatch_whl, and kohaku Change-Id: I686a85996858204c20fd05ef24787a0487817c34 Signed-off-by: Philip Chen <philipchen@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/32513 Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org> Reviewed-by: Furquan Shaikh <furquan@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2019-04-29soc/intel: Add GPI interrupt config register offset infoKarthikeyan Ramasubramanian
Add the offset information for GPI interrupt status and enable register in the pad_community structure. Populate the concerned information for individual SoCs. This offset information is required to clear the interrupt configuration during the bootup. BUG=b:130593883 BRANCH=None TEST=Ensure that the interrupt configuration are cleared during bootup. Ensured that the system boots to ChromeOS. Change-Id: I8af877a734e8d49b700d720b736da8764985a8f8 Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/32446 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Furquan Shaikh <furquan@google.com>
2019-04-29soc/intel/cannonlake: Modify dq_map to provide for 6 entriesPaul Fagerburg
Intel's DQ_DQS_RComp_Info_Utility generates data for 6 entries. MRC will return errors if we don't have all 6 entries in the map. BRANCH=none BUG=b:131103736 TEST=ensure the firmware builds without error; I don't have hardware available to test this just yet. Change-Id: I20a768de0e4440d7dde7b717794c4e2d0c62819c Signed-off-by: Paul Fagerburg <pfagerburg@chromium.org> Reviewed-on: https://review.coreboot.org/c/coreboot/+/32475 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Furquan Shaikh <furquan@google.com>
2019-04-26soc/{amd,intel}/chip: Use local include for chip.hElyes HAOUAS
Change-Id: Ic1fcbf4b54b7d0b5cda04ca9f7fc145050c867b8 Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr> Reviewed-on: https://review.coreboot.org/c/coreboot/+/32014 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Nico Huber <nico.h@gmx.de>
2019-04-18soc/intel/cnl: Generate DMAR ACPI tableJohn Zhao
The platform supports Virtualization Technology for Directed I/O. Generate DMAR acpi table if VT-d feature is enabled. BUG=b:130351429 TEST=Booted to kernel and verified the DMAR table contents. Change-Id: I4e1ee5244c67affb13947436d81628c5dc665c9e Signed-off-by: John Zhao <john.zhao@intel.com> Signed-off-by: Pratik Prajapati <pratikkumar.v.prajapati@intel.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/31917 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Nico Huber <nico.h@gmx.de> Reviewed-by: Furquan Shaikh <furquan@google.com> Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
2019-04-11soc/intel/cannonlake: Correct the GPE DWx mapping for GPIO groupsAamir Bohra
This implementation corrects the GPE DWx mapping for GPIO groups. The assignments is done in GPIO MISCFG register for all GPIO communities. And configures the which GPIO communities get register as Tier1. BUG=b:121212459 TEST: Verified the GPIO MISCFG is getting set as per updated map. Change-Id: I451997367025a6dc9e5931bd649524e935ad6aca Signed-off-by: Aamir Bohra <aamir.bohra@intel.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/32175 Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com> Reviewed-by: Furquan Shaikh <furquan@google.com> Reviewed-by: Lijian Zhao <lijian.zhao@intel.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2019-04-08Replace remaining IS_ENABLED(CONFIG_*) with CONFIG()Nico Huber
Another run of find src/ -type f | xargs sed -i -e 's/IS_ENABLED\s*(CONFIG_/CONFIG(/g' Change-Id: I3243197ab852a3fbc3eb2e2e782966a350b78af2 Signed-off-by: Nico Huber <nico.h@gmx.de> Reviewed-on: https://review.coreboot.org/c/coreboot/+/32224 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr> Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Julius Werner <jwerner@chromium.org>
2019-03-29soc/intel/cannonlake: Ignore GBE LTRLijian Zhao
Ignore integrated GBE controller LTR setting to make it wake up from s0ix with 10/100M cable attached. BUG=b:122435844 TEST= Test on sarien platorm, after the changes sytem can wake by WOL, and also checked SLP_S0 residency can increase with 10/100M cable and battery connected. Signed-off-by: Lijian Zhao <lijian.zhao@intel.com> Change-Id: Iec7dd197b8a456751f8e4dcb19e3e153f5888613 Reviewed-on: https://review.coreboot.org/c/coreboot/+/31888 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
2019-03-25soc/intel/cannonlake: Clear PMCON status bitsKrishna Prasad Bhat
The prev_sleep_state value was showing 5 even after warm reboot, once the SUS_PWR_FLR bit is being set. This bit was not being cleared. Hence clearing the PMCON status bits. BUG=b:128482282 BRANCH=None TEST=In cbmem logs, check for value of “prev_sleep_state” using command cbmem –c | grep “prev_sleep_state” For cold reboot, "prev_sleep_state 5" For warm reboot, "prev_sleep_state 0" Change-Id: If9863d52ed3c61b6a160df53f023b0787eaaed68 Signed-off-by: Krishna Prasad Bhat <krishna.p.bhat.d@intel.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/31902 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
2019-03-16soc/intel/cannonlake: Add required FSP UPD changes for CMLSubrata Banik
This patch adds required FSP UPD changes for CometLake SoC. Also this patch tries to create common parse logic for CometLake as well as cannonlake SOC. We parse device tree parameters for PCI devices and fill values in FSP UPDs. We fill UPDs based on pci device config as well as SerialIoDev config of devicetree. For PCI devices, if PCI device is disabled from devicetree, we'll assign disable value to FSP UPD. In case devicetree doesn't fill this parameter or value is invalid in SerialIoDev config, default mode will be set to PCI. In case of valid value, we'll fill the same value into FSP UPD. BUG=none BRANCH=none TEST=check if CML board boots and proper UPD values are filled. Change-Id: Ib92b660409ab01d70358042b2ed29b8bf9cab26d Signed-off-by: Subrata Banik <subrata.banik@intel.com> Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/31284 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Furquan Shaikh <furquan@google.com> Reviewed-by: V Sowmya <v.sowmya@intel.com>
2019-03-13soc/intel/cannonlake: Allow mainboard to override DRAM part numberFurquan Shaikh
In order to support mainboards that do not store DRAM part number in the traditional way i.e. within the CBFS SPD for soldered memory, this change provides a runtime callback to allow mainboards to provide DRAM part number from a custom location e.g. external EEPROM on hatch. For other boards it should be a NOP since the weak implementation of mainboard_get_dram_part_num does nothing. BUG=b:127609572 Change-Id: I9b2d4c33fc378b9a24b111971ec2bfdb5f8d57d0 Signed-off-by: Furquan Shaikh <furquan@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/31850 Reviewed-by: Aaron Durbin <adurbin@chromium.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2019-03-08coreboot: Replace all IS_ENABLED(CONFIG_XXX) with CONFIG(XXX)Julius Werner
This patch is a raw application of find src/ -type f | xargs sed -i -e 's/IS_ENABLED\s*(CONFIG_/CONFIG(/g' Change-Id: I6262d6d5c23cabe23c242b4f38d446b74fe16b88 Signed-off-by: Julius Werner <jwerner@chromium.org> Reviewed-on: https://review.coreboot.org/c/coreboot/+/31774 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Patrick Georgi <pgeorgi@google.com>
2019-03-04arch/io.h: Drop unnecessary includeKyösti Mälkki
Change-Id: I91158452680586ac676ea11c8589062880a31f91 Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com> Reviewed-on: https://review.coreboot.org/c/31692 Reviewed-by: Patrick Georgi <pgeorgi@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2019-03-04soc/intel/cannonlake: Move common definitions to a header fileRizwan Qureshi
Move common definitions for PCH H and LP to a common header. Change-Id: If47692ecb05134db1ee6c0fb10125d6a1b67f127 Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com> Reviewed-on: https://review.coreboot.org/c/31621 Reviewed-by: Lijian Zhao <lijian.zhao@intel.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2019-02-27soc/intel/cannonlake: Add a config for configuring SD_VDD1_PWR_EN#Rizwan Qureshi
SD controller in CNL-PCH provides a ability to configure the behavior of SD_VDD1_PWR_EN# as an active high or low signal. FSP provides an UPD "SdCardPowerEnableActiveHigh" to control the same. However, for platforms using SD_VDD1_PWR_EN# as active high, the SDXC card connector is always powered and may impact system power. This is because SD_VDD1_PWR_EN# does not de-assert during SDXC D3 or when SD card is not inserted. Workaround is to change the pad ownership of SD_VDD1_PWR_EN to GPIO and force the TX buffer to low in _PS3. And restore the pad mode to native function in _PS0. Hence add a Kconfig option to update the UPD, which the board can select based on how the SD_VDD1_PWR_EN is implemented on it. And, the workaround gets applied based on this config. BUG=b:123350329 Change-Id: Iee262d7ecdf8c31362aec3d95dd9b3e8359e0c25 Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com> Reviewed-on: https://review.coreboot.org/c/31445 Reviewed-by: Furquan Shaikh <furquan@google.com> Reviewed-by: Nico Huber <nico.h@gmx.de> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2019-02-27soc/intel/cannonlake: Add ASL functions to manipulate RX/TX buffersRizwan Qureshi
Add a function in gpio ASL library to enable/disable pad Rx/Tx Buffers. BUG=b:123350329 Change-Id: I6c40d79debb61b0c4e96e485b410d446b77d9cf6 Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com> Reviewed-on: https://review.coreboot.org/c/31619 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Nico Huber <nico.h@gmx.de> Reviewed-by: Furquan Shaikh <furquan@google.com>
2019-02-26soc/intel/cannonlake: Update GPIO definitions for Virtual GPIORizwan Qureshi
Denote appropriate reserved groups as virtual GPIOs in Cannonlake LP/H SoC. Change-Id: I4da161b91f83749b0ae29b387b5c99c1c3f706d8 Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com> Reviewed-on: https://review.coreboot.org/c/31552 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Lijian Zhao <lijian.zhao@intel.com> Reviewed-by: Furquan Shaikh <furquan@google.com>
2019-02-22soc/intel/cannonlake: Add ASL function for setting pad modeRizwan Qureshi
Add a function in gpio ASL library to set pad mode. BUG=b:123350329 Change-Id: I6c683f27ddffc3132001706d1694c71bb5664577 Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com> Reviewed-on: https://review.coreboot.org/c/31444 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Furquan Shaikh <furquan@google.com>
2019-02-21soc/intel/cannonlake: Add field to identify single channel memoryShelley Chen
Variants of Hatch need to accommodate single channel DDR. Also, removing const modifier as we'll need to set these fields incrementally now. For the single channel configuration, we set MemorySpdPtr10 to 0. For the dual channel configuration, we set MemorySpdPtr10 to MemorySpdPtr00. BUG=b:123062346, b:122959294 BRANCH=None TEST=Boot into current boards and ensure that we have 2 channels as expected Change-Id: Ice22b103664187834e255d1359bfd9b51993b5b6 Signed-off-by: Shelley Chen <shchen@google.com> Reviewed-on: https://review.coreboot.org/c/31262 Reviewed-by: Patrick Rudolph <patrick.rudolph@9elements.com> Reviewed-by: Furquan Shaikh <furquan@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2019-02-15soc/intel/cannonlake: Define VR settingsRoy Mingi Park
Define VR settings configuration as per board design. BUG=N/A TEST=Build and boot up into sarien platform. Change-Id: Ic9927943b1f8fab687659fd1d6da0e3988a3aba2 Signed-off-by: Roy Mingi Park <roy.mingi.park@intel.com> Reviewed-on: https://review.coreboot.org/c/31405 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
2019-02-07soc/intel/cannonlake: Configure GPIOs again after FSP-S is doneFurquan Shaikh
FSP-S is currently configuring GPIOs that it should not. This results in issues where mainboard devices don't behave as expected e.g. host unable to receive TPM interrupts as the pad for the interrupt is re-configured as something else. Until FSP-S is fixed, this change adds a workaround by reconfiguring GPIOs after FSP-S is run. All mainboards need to call cnl_configure_pads instead of gpio_configure_pads so that SoC code can maintain a reference to the GPIO table and use that to re-configure GPIOs after FSP-S is run. BUG=b:123721147 BRANCH=None TEST=Verified that there are no TPM IRQ timeouts in boot log on hatch. Change-Id: I7787aa8f185f633627bcedc7f23504bf4a5250b4 Signed-off-by: Furquan Shaikh <furquan@google.com> Reviewed-on: https://review.coreboot.org/c/31250 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
2019-01-25soc/intel/cannonlake: Export function to set After G3 stateDuncan Laurie
Export the SOC level function to set the After G3 state so it can be changed by the mainboard. The setting will be restored by a normal boot but in some circumstances coreboot wants to ensure that it will be powered up again after a reset. BUG=b:121380403 TEST=update cr50 firmware on sarien and reboot and ensure the host does not power off after the cr50 initiated reset. Change-Id: I6cd572ac91229584b9907f87bb4b340963203c32 Signed-off-by: Duncan Laurie <dlaurie@google.com> Reviewed-on: https://review.coreboot.org/c/31056 Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2019-01-16soc/intel/cannonlake: Add processor power limits control supportSumeet Pawnikar
Add processor power limits control support to configure values. BRANCH=None BUG=b:122343940 TEST=Built and tested on Arcada system Change-Id: I5990dc05b51481a0074855914cef20cf07378cde Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com> Reviewed-on: https://review.coreboot.org/c/30907 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Patrick Georgi <pgeorgi@google.com>
2019-01-16buildsystem: Promote rules.h to default includeKyösti Mälkki
Does not fix 3rdparty/, *.S or *.ld or yet. Change-Id: I66b48013dd89540b35ab219d2b64bc13f5f19cda Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com> Reviewed-on: https://review.coreboot.org/c/17656 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Nico Huber <nico.h@gmx.de>
generated by cgit v1.2.3 (git 2.25.1) at 2024-12-29 01:41:02 +0000