| Age | Commit message (Collapse) | Author |
|---|
|
Signed-off-by: Ritul Guru <ritul.bits@gmail.com>
Change-Id: I07d5aaac9c05986e8a952c7e670d002d864e18d7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67170
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Use dynamic power and thermal configuration (DPTC) via ACPI ALIB calls
to throttle the SOC when there is no battery or critically low battery,
to enable the SOC to boot without overwhelming the AC charger and
browning out.
DPTC is not enabled for low/no battery mode with this CL. It will be
enabled for Skyrim in a following CL.
BRANCH=none
BUG=b:217911928
TEST=Boot skyrim
Signed-off-by: Tim Van Patten <timvp@google.com>
Change-Id: Ifeddb99e97af93b40a5aad960d760e4c101cf086
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67189
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add support for DPTC by calling SB.DPTC() as part of PNOT().
BRANCH=none
BUG=b:217911928
TEST=Boot skyrim
Signed-off-by: Tim Van Patten <timvp@google.com>
Change-Id: Ifc332bfc4d273031c93b77673224b4f3c2871fb1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67694
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add DPTC Low/No battery VRM limit registers to throttle the SOC.
BRANCH=none
BUG=b:217911928
TEST=Build skyrim
Signed-off-by: Tim Van Patten <timvp@google.com>
Change-Id: I9c4ed227b54efbab9f03d6acf64b1160ad73f460
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67692
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Set the DPTC VRM limit values for normal mode.
BRANCH=none
BUG=b:217911928
TEST=Boot skyrim
Signed-off-by: Tim Van Patten <timvp@google.com>
Change-Id: I2041a713323f039dcfdacdfa43e74cf450c3c0d1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67691
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add VRM DPTC limit registers. These are required when throttling the SOC
for low/no battery mode to prevent the SOC from overwhelming the
charger.
b/245942343 is tracking passing these additional fields to the FSP and
having the FSP configure them.
BRANCH=none
BUG=b:217911928
TEST=Build skyrim
Signed-off-by: Tim Van Patten <timvp@google.com>
Change-Id: Ie62129d967192f9a9cf654b1854d7dbe4324802a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67378
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Update acpigen_write_alib_dptc() to support "low/no battery mode",
which throttles the SOC when there is no battery connected or the
battery charge is critically low.
This is in preparation for enabling this functionality for Mendocino.
BUG=b:217911928
TEST=Build zork
TEST=Boot nipperkin
TEST=Boot skyrim
Signed-off-by: Tim Van Patten <timvp@google.com>
Change-Id: Icea10a3876a29744ad8485be1557e184bcbfa397
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66804
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
There are platforms equipped with AMD SoC where I2C3 controller
connected to TPM device is shared between X86 and PSP. In order to
handle this, PSP acts as an I2C-arbitrator, where x86 (kernel) sends
acquire and release requests to be accepted by PSP.
Introduce new CONFIG for Mendocino SoCs similar to what we have for
Cezanne.
BUG=b:241878652
BRANCH=none
Signed-off-by: Jan Dabros <jsd@semihalf.com>
Change-Id: I015a24715271d2b26c0bd3c9425e20fb2987a954
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67674
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
SOC_AMD_COMMON_BLOCK_ACPI_DPTC can be enabled conditionally for any
skyrim boards, similar to mainboard/google/zork/Kconfig. This makes the
value dptc_tablet_mode_enable redundant.
This CL removes dptc_tablet_mode_enable so DPTC is controlled entirely
with the Kconfig value SOC_AMD_COMMON_BLOCK_ACPI_DPTC. This means DPTC
is only included for boards that actually enable it.
BRANCH=none
BUG=b:217911928
TEST=emerge-skyrim coreboot
Signed-off-by: Tim Van Patten <timvp@google.com>
Change-Id: I73fca5a16826313219247f452d37fb526ad4f4df
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67639
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
SOC_AMD_COMMON_BLOCK_ACPI_DPTC can be enabled conditionally for any
guybrush boards, similar to .mainboard/google/zork/Kconfig This makes
the value dptc_tablet_mode_enable redundant.
This CL removes dptc_tablet_mode_enable so DPTC is controlled entirely
with the Kconfig value SOC_AMD_COMMON_BLOCK_ACPI_DPTC. This means DPTC
is only included for boards that actually enable it.
BRANCH=none
BUG=b:217911928
TEST=emerge-guybrush coreboot
Signed-off-by: Tim Van Patten <timvp@google.com>
Change-Id: I07f1266fa80a6c9ee4ec3b3ba970a70c6c72fb54
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67638
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Moving the config value SOC_AMD_COMMON_BLOCK_ACPI_DPTC to
soc/amd/picasso/Kconfig and conditionally enabling it for only Morphius
boards makes the value dptc_tablet_mode_enable redundant.
This CL removes dptc_tablet_mode_enable so DPTC is controlled entirely
with the Kconfig value SOC_AMD_COMMON_BLOCK_ACPI_DPTC. This means DPTC
is only included for boards that actually enable it.
BRANCH=none
BUG=b:217911928
TEST=Build zork
Signed-off-by: Tim Van Patten <timvp@google.com>
Change-Id: Ic54a9bb491234088be8184bec8b09e2e31ffa298
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67635
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
AMD CPUs have a convenient MSR that allows to set the SMBASE in the save
state without ever entering SMM (e.g. at the default 0x30000 address).
This has been a feature in all AMD CPUs since at least AMD K8. This
allows to do relocation in parallel in ramstage and without setting up a
relocation handler, which likely results in a speedup. The more cores
the higher the speedup as relocation was happening sequentially. On a 4
core AMD picasso system this results in 33ms boot speedup.
TESTED on google/vilboz (Picasso) with CONFIG_SMI_DEBUG: verify that SMM
is correctly relocated with the BSP correctly entering the smihandler.
Change-Id: I9729fb94ed5c18cfd57b8098c838c08a04490e4b
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/64872
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Move enabling SOC_AMD_COMMON_BLOCK_ACPI_DPTC from
soc/amd/picasso/Kconfig to mainboard/google/zork/Kconfig and
conditionally enable it only for Morphius boards.
This reduces which boards/variants have DPTC enabled to only those that
actually use it.
BRANCH=none
BUG=b:217911928
TEST=Build zork
Signed-off-by: Tim Van Patten <timvp@google.com>
Change-Id: Iddebcf5dbadae135c8110e2afd9ad76ef7dcc09d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67637
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Conditionally include dptc.asl based on the Kconfig value
SOC_AMD_COMMON_BLOCK_ACPI_DPTC.
BRANCH=none
BUG=b:217911928
TEST=Build zork
TEST=Build guybrush
TEST=Build skyrim
TEST=Build majolica
Change-Id: Idd94af8e8b2d7973abc0fb939e4600189e21656a
Signed-off-by: Tim Van Patten <timvp@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67620
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Now that the FSP binary check logic is fixed to only check the FSP files
if ADD_FSP_BINARIES is selected, the default paths for the not yet
published Cezanne FSP binaries can be added without breaking abuild.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I9950a1fe7bd1b21109cca9631de1a8f1d265d9b2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57216
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
Only check if the FSP_M size is small enough to fit inside the memory
region reserved for it if ADD_FSP_BINARIES selected.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Suggested-by: Nico Huber <nico.h@gmx.de>
Change-Id: I6a115412c113eb0d02b8d4dfc2bb347305f97809
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57223
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
Locking SMM as part of the AP init avoids the need for
CONFIG_PARALLEL_MP_AP_WORK to lock it down.
Change-Id: Ibcdfc0f9ae211644cf0911790b0b0c5d1b0b7dc9
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/64871
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I7c457ab69581f8c29f2d79c054ca3bc7e58a896e
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/64870
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This is the same for all supported AMD hardware.
Change-Id: Ic6b954308dbb4c5a2050f1eb8f15acb41d0b81bd
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67617
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Being divided by 1000 causes data loss and the loss is expand by
muliplication.
So we just set a lower divisor before muliplication.
BUG=b:185922528
Change-Id: Ib43103cc62c18debea3fd2c23d9c30fb0ecd781b
Signed-off-by: Zheng Bao <fishbaozi@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67050
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Add support for having different Security Patch Level (SPL) table files
in the read-only and the read-write A/B partitions. This allows the SPL
table file in the main or RO FMAP partition to only cover the embedded
firmware binaries in that partition and have a separate SPL file in the
RW A and B partitions that covers the embedded firmware binaries in the
RW partitions.
BUG=b:243470283
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I1ba8c370ce14f7ec88e7ef2f9d0b64d6bb4fa176
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67555
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martin.roth@amd.corp-partner.google.com>
|
|
Since mono_time is now 64-bit, the utility functions interfacing with
mono_time should also be 64-bit so precision isn't lost.
Fixed build errors related to printing the now int64_t result of
stopwatch_duration_[m|u]secs in various places.
BUG=b:237082996
BRANCH=All
TEST=Boot dewatt
Change-Id: I169588f5e14285557f2d03270f58f4c07c0154d5
Signed-off-by: Rob Barnes <robbarnes@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66170
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
The following boards are setting DTPC tablet mode values without
corresponding device tree values, meaning they are effectively setting
"random" values for tablet mode:
1. Cezanne
2. Mendocino
The device tree has tablet mode disabled, so the code should never be
exercised, but this CL removes it entirely to cleanup "dead" code.
BRANCH=none
BUG=b:217911928
TEST=Build nipperkin
TEST=Boot skyrim
Signed-off-by: Tim Van Patten <timvp@google.com>
Change-Id: Ide96f255b69670d1b4c37ca2f94cc3504a958b57
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67181
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Refactor AMD DPTC tablet mode in preparation for adding low/no battery
DPTC settings.
1. Refactor and simplify acpigen_write_alib_dptc() into the following
functions:
- acpigen_write_alib_dptc_default()
- acpigen_write_alib_dptc_tablet()
2. Add device tree register value dptc_tablet_mode_enable to control
whether DPTC tablet mode is enabled for a variant.
3. Add dptc.asl to perform the necessary ACPI checking before modifying
the DPTC settings.
BRANCH=none
BUG=b:217911928
TEST=Build zork
TEST=Build nipperkin
TEST=Boot skyrim
Change-Id: I2518fdd526868c9d5668a6018fd3570392e809c0
Signed-off-by: Tim Van Patten <timvp@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66994
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Enable the APOB_HASH feature. This improves boot times by ~10ms.
BUG=b:193557430
TEST=boot to OS and verify boot time improvement
Signed-off-by: Fred Reitberger <reitbergerfred@gmail.com>
Change-Id: I9628b67cd3206ffdbef23162c453dc183c69e5a5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67377
Reviewed-by: Martin Roth <martin.roth@amd.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Comparing the APOB in RAM to flash takes a significant amount of time
(~11ms). Instead of comparing the entire APOB, use a fast hash function
and compare just that. Reading, hashing, and comparing the hash take
~70 microseconds.
BUG=b:193557430
TEST=compile and boot to OS in chausie with and without this option set
Signed-off-by: Fred Reitberger <reitbergerfred@gmail.com>
Change-Id: I241968b115aaf41af63445410660bdd5199ceaba
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67301
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martin.roth@amd.corp-partner.google.com>
|
|
dptc_enable is being treated as a bool, so convert to explicitly be a
bool.
BRANCH=none
BUG=b:217911928
TEST=Build zork
TEST=Build guybrush
TEST=Build skyrim
Change-Id: I0e93d892b3b8016221812c8b9ec6c257dcf13ef5
Signed-off-by: Tim Van Patten <timvp@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67188
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add additional DPTC parameter IDs that are necessary when throttling the
SOC due to low/no battery.
These additional parameters are used in later CLs.
BRANCH=none
BUG=b:217911928
TEST=Build zork
TEST=Build nipperkin
TEST=Build skyrim
Signed-off-by: Tim Van Patten <timvp@google.com>
Change-Id: I9e944d7c620414ec92d08a3d1173ba281d593ffc
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67182
Reviewed-by: Martin Roth <martin.roth@amd.corp-partner.google.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
Definition of FIRMWARE_LOCATION, POUND_SIGN, DEP_FILES,
amd_microcode_bins are moved to common Makefile.inc.
Change-Id: I5a0ea27002e09d0b879bafad37a5d418ddb4e644
Signed-off-by: Zheng Bao <fishbaozi@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62658
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jon Murphy <jpmurphy@google.com>
|
|
Select SOC_AMD_COMMON_BLOCK_ESPI_EXTENDED_DECODE_RANGES and remove the
TODO from SOC_AMD_COMMON_BLOCK_HAS_ESPI.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I90e3bf3f196e22b428b01ea0437c1224702d2b44
Reviewed-on: https://review.coreboot.org/c/coreboot/+/64055
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jon Murphy <jpmurphy@google.com>
|
|
Compile-time support of DPTC is controlled by
EC_ENABLE_AMD_DPTC_SUPPORT in each variant's ec.h file. This CL removes
EC_ENABLE_AMD_DPTC_SUPPORT and replaces it with the Kconfig value
SOC_AMD_COMMON_BLOCK_ACPI_DPTC.
Each variant's run-time support of DPTC continues to be controlled by
the variant's overridetree.cb "dptc_enable" value.
BRANCH=none
BUG=b:217911928
TEST=Build zork
TEST=Boot skyrim
Signed-off-by: Tim Van Patten <timvp@google.com>
Change-Id: Ic101e74bab88e20be0cb5aaf66e4349baa1432e3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67180
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martin.roth@amd.corp-partner.google.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
The CPPC table value for UEFI BIOS has been changed. The code has been
merged to AGESA. We can get the value by dumping ACPI table. Then we
align the coreboot code with the new value.
BUG=b:190420984
Change-Id: I091ab3bbc5f94961f8b366a3fa00f50f5c9fa182
Signed-off-by: Zheng Bao <fishbaozi@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63632
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
The size of the input parameter to RESET_SYSTEM svc call is expected to
be 4 bytes. Fix the reset_system type from enum to uint32_t.
BUG=b:243476183
TEST=Build and boot to OS in Skyrim with PSP verstage. Trigger a system
reset to ensure that the system is reset successfully.
Change-Id: I6319a1dfc89602722c1c2b1c4ee744493ae8b33f
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67117
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I68667d084001c753e74ba480fa7b6e09b1b88cb8
Signed-off-by: Ritul Guru <ritul.bits@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66369
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Only 16 MByte of the SPI flash can be mapped right below the 4 GB
boundary.
In case of a larger SPI flash size, still only the 16 MByte region
starting at 0xff000000 can be configured as WRPROT and be reserved for
the MMIO mapped SPI flash region. The next 16 MByte MMIO region starting
at address 0xfe000000 contain for example the LAPIC MMIO region, the
ACPIMMIO region and the UART/I2C controller MMIO regions which shouldn't
be configured as WRPROT. Reserving this region for the MMIO mapped SPI
flash would also result in an overlap with the MMIO resources mentioned
above.
In the case of a smaller SPI flash, reserving the full 16 MByte flash
MMIO region makes sure that the resource allocator won't try to put
anything else in the lower parts of the 16 MByte SPI mapping region.
To avoid the issues described above, always reserve/cache the maximum
amount of 16 MBytes of flash that can be mapped below 4 GB.
TEST=On boards with 16 MByte SPI flash chips, the resulting image of a
timeless build doesn't change with this patch. Verified this on Chausie
(Mendocino), Majolica (Cezanne), Cereme (Picasso) and Google/Careena
(Stoneyridge). On Mandolin (Picasso) with an 8 MByte flash, the
resulting image of a timeless build is different, but neither the
coreboot console output nor the Linux dmesg output shows any errors that
might be related to this change.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ie12bd48e48e267a84dc494f67e8e0c7a4a01a320
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66700
Reviewed-by: Martin Roth <martin.roth@amd.corp-partner.google.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Voltage set based on standard configuration for each type.
TEST=build/boot google/skyrim, verify output in cbmem console log,
DMI type 17 table.
Change-Id: I9b1e68a9417e43cbb9c55b4c471664f3f9090342
Signed-off-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66981
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
Since the frequency field is deprecated, print the max/configured MT/s
speeds instead.
TEST=build/boot google/skyrim, verify output in cbmem console log
Change-Id: Icee5af762ca37c3b2ec8c9a52a7f32fb848390b0
Signed-off-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66980
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
Hook up newly-added method to convert from frequency to MT/s so that
boards which use (LP)DDR5 report their capability properly.
BUG=b:239000826
TEST=build/boot google/skyrim, verify SMBIOS Type 17 table reports
DRAM speeds correctly.
Change-Id: I694b6c227a8d8fb40c897053808bc79df330ed0c
Signed-off-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66954
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
smn_read32 is used in this file, so include the header file with the
function prototype so that the file compiles successfully.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I5bef96cd08f22b3475e8b5ba4e984a6e1ab4da36
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66913
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
|
|
Since the I2C controller is part of the FCH, move the early
initialization from bootblock.c to early_fch.c which also matches what
the newer AMD SoCs do.
TEST=Successfully boots on google/liara and all I2C/cr50/TPM functions
appear to work properly
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I22d3a8888eaa34ea612da719c408c0083769e806
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66866
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The functionality of sb_enable_lpc is implemented in the common LPC
support code as lpc_enable_controller. This gets called by the common
lpc_early_init which also calls lpc_disable_decodes and lpc_set_spibase.
The lpc_set_spibase call was already done in bootblock_fch_early_init,
so the main change in code behavior is that now lpc_disable_decodes gets
called during early FCH initialization. The lpc_enable_port80 and
sb_lpc_decode calls after the lpc_early_init code will reenable some of
the decodes.
TEST=Successfully boots on google/liara, cbmem and dmesg logs look clean
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ia58a6f609fa149a6c09ed99f08bdc4f05eb56f96
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66841
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I35dd9a2f0520077913bd3d8f408206dea1b30acb
Signed-off-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66867
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
The PCI config space of the SMBus device has a secondary mapping as an
ACPIMMIO bank. Since the PCI device is on bus 0, it's already available
early in boot after the enable_pci_mmconf call, so there's no need to
use the ACPIMMIO mapping instead of the PCI config space mapping.
Verstage on PSP could theoretically access the PCI config space via the
0xcf8/0xcfc register pair, but since verstage on PSP doesn't have the
ACPIMMIO mapping anyway, we won't loose any functionality here.
Change-Id: I5c8ce8de0a6ab0ed41e7e8a5980d0f0510aaa993
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42685
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
This is sort-of reverts commit cbf290c692b2 ("soc/amd/sabrina: drop
CPPC code"), since it turned out that the CPPC feature is supported
on Sabrina (now Mendocino) despite this being missing from the
documentation I looked at when writing the patch referenced above.
Since the CPPC ACPI code generation functionality has been moved to
common code, this isn't a direct revert.
BUG=b:237336330
TEST=None
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I1c059653eeae207d723c77e8a78b19c86e362296
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66401
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Mendocino has more eSPI decode ranges than Picasso or Cezanne. To
support these additional ranges, introduce a new Kconfig option
SOC_AMD_COMMON_BLOCK_ESPI_EXTENDED_DECODE_RANGES that can be selected by
the SoCs that support the additional eSPI IO/MMIO decode ranges.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ib761cdf201c35805d68cf5e8e462607ffd9fa017
Reviewed-on: https://review.coreboot.org/c/coreboot/+/64054
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
Now that we have functionality to get the minimal and nominal
frequencies, the corresponding fields in the CPPC config can now be
populated. If the HOB isn't present and/or the frequency values
could not be obtained, CPPC_UNSUPPORTED is still used; otherwise the
HOB-provided frequency in MHz is used for those two fields.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Signed-off-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Change-Id: Id3257690a3388d44ceceb7ac4f1db3d49e195caa
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66551
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add common AMD FSP functionality to get the nominal and minimal CPU core
CPPC frequencies. Those functions will be used in the _CPC ACPI object
generation in a follow-up patch.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Signed-off-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Change-Id: I68ebdf610795d2673e0118a732f54f5f719b73c0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66550
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The SMI sleep entry handler will access the SMN space via the index/data
register at PCI config space offsets 0xb8 and 0xbc of the device at bus
0, device 0, function 0. This register pair is also used by other
software components running on the x86 cores after boot, so it should be
saved and restored at the beginning/end of the SMI handler if it
accesses SMN. The sleep entry SMI handler is a special case, since the
OS is already done at the moment we enter the sleep SMI handler which is
the last code that gets run on the x86 cores before entering S3/4/5.
BUG=b:237004699
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I0980562ef8a61489082a81c71d6d00d0786d68cb
Reviewed-on: https://review.coreboot.org/c/coreboot/+/65529
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
Checking if the return value of the fsp_find_extension_hob_by_guid call
is NULL should make the code a bit easier to read.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I6bdb07eab6da80f46c57f5d7b3c894b41ac23b8a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66699
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
The PSP currently uses a hard coded GPIO for the TPM IRQ. Not all board
versions use the same GPIO. This method allows the mainboard to pass
in the correct GPIO.
BUG=b:241824257
TEST=Boot guybrush and verify PSP message prints
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: Ie05d095d7f141d6a526d08fbf25eb2652e96aa49
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66614
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Since bootblock_soc_early_init gets called before
bootblock_mainboard_early_init which does the early GPIO setup, external
I2C level shifters that are controlled by GPIOs might not be enabled yet.
Moving the reset_i2c_peripherals call to bootblock_soc_init makes sure
that the early GPIO setup is already done when reset_i2c_peripherals is
called.
Haven't probed any SCL signal on the non-SoC side of the I2C level
shifters yet, but the waveform on the SCL pin of I2C3 on the SoC of a
barla/careena Chromebook doesn't have the longer than expected SCL
pulses any more.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: If02140aef56ed6db7ecee24811724b5b24e54a91
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57291
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
This reverts commit 8b1c6c6cb384c89659abbd043c2566df358d8f95. With
updated APCB, eSPI configuration carries over to bootblock. Hence eSPI
does not need to be re-initialized in bootblock.
BUG=b:241426419
TEST=Build and boot to OS in Skyrim with PSP verstage.
Cq-Depend: chrome-internal:4929421
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Change-Id: I426b07329d4a0154d915381c99dcc9746b7a3d7c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66697
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Since the path after the chip keyword needs to point to the directory
that contains the chipset's chip.h file, change this from
soc/amd/rembrandt to soc/amd/mendocino.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I63334fbd59e74df491035b5cf7e296818cc02665
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66688
Reviewed-by: ritul guru <ritul.bits@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
The Cezanne CPPC ACPI table generation code also applies to Sabrina, so
move it to the common AMD SoC code directory so that it can be used for
Sabrina too.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I5ce082a27429948f8af7f55944a1062ba03155da
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66400
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
This reverts commit Ic152c295954d33ef1acddb3b06f0c6bbfbfb38ae.
There was a bug that caused the SMU to hang when writing port80. it has
since been resolved, so revert this workaround.
BUG=b:227201571
TEST=Build and boot to OS in Skyrim.
Signed-off-by: Jon Murphy <jpmurphy@google.com>
Change-Id: I5f10e282ab03756c7dbfb48182940f979eb122e4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66470
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
|
|
We want to extend the vb2ex_hwcrypto APIs on the vboot side to allow
passing 0 for the data_size parameter to vb2ex_hwcrypto_digest_init()
(see CL:3825558). This is because not all use cases allow knowing the
amount of data to be hashed beforehand (most notable the metadata hash
for CBFS verification), and some HW crypto engines do not need this
information, so we don't want to preclude them from optimizing these use
cases just because others do.
The new API requirement is that data_size may be 0, which indicates that
the amount of data to be hashed is unknown. If a HW crypto engine cannot
support this case, it should return VB2_ERROR_EX_HWCRYPTO_UNSUPPORTED to
those calls (this patch adds the code to do that to existing HW crypto
implementations). If the passed-in data_size value is non-zero, the HW
crypto implementation can trust that it is accurate.
Also reduce a bit of the console spew for existing HW crypto
implementations, since vboot already logs the same information anyway.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: Ieb7597080254b31ef2bdbc0defc91b119c618380
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66621
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
'Mendocino' was an embargoed name and could previously not be used
in references to Skyrim. coreboot has references to sabrina both
in directory structure and in files. This will make life difficult
for people looking for Mendocino support in the long term. The code
name should be replaced with "mendocino".
BUG=b:239072117
TEST=Builds
Cq-Depend: chromium:3764023
Cq-Depend: chromium:3763392
Cq-Depend: chrome-internal:4876777
Signed-off-by: Jon Murphy <jpmurphy@google.com>
Change-Id: I2d0f76fde07a209a79f7e1596cc8064e53f06ada
Reviewed-on: https://review.coreboot.org/c/coreboot/+/65861
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martin.roth@amd.corp-partner.google.com>
|
|
The default state for the IRQ lines when the eSPI controller comes out
of reset is high. This is because the IRQ lines are shared with the
other IRQ sources using AND gates. This means that in order to not cause
any spurious interrupts or miss any interrupts, the IO-APIC must use a
low polarity trigger.
On zork/guybrush/skyrim the eSPI IRQs are currently working as follows:
* On power on/resume the eSPI controller drives IRQ 1 high.
* eSPI controller gets configured to not invert IRQ 1.
* OS configures IO-APIC IRQ 1 as Edge/High.
* EC writes to HIKDO (Keyboard Data Out) which causes the EC to set IRQ1
high.
* eSPI controller receives IRQ 1 high, doesn't invert it, and leaves IRQ
1 as high. This results in missing the first interrupt.
* When the x86 reads from HIKDO, the EC deasserts IRQ1. This causes the
eSPI controller to set IRQ1 to low. We are now primed to catch the
next edge high interrupt. This is generally not a problem since the
linux driver will probe the 8042 with interrupts off.
On S3/S0i3 resume since the eSPI controller comes out of reset driving
the IRQ lines high, we trigger a spurious IRQ since the IO-APIC is
configured to trigger on edge high. This results in the 8042 controller
getting incorrectly marked as a wake trigger.
By configuring the IO-APIC to use low polarity interrupts, we no longer
lose the first interrupt. This also means we can use a level interrupt
to match what the EC actually asserts.
We use the `Interrupt` keyword instead of the `IRQ` keyword in the ACPI
because the linux kernel will ignore the level/polarity parameters
for the `IRQ` keyword and default to `edge/high. `Interrupt` doesn't
have this problem.
The PIC is not currently configured anywhere and it defaults to an
edge/high trigger. We could add some code to configure the PICs trigger
register, but I don't think we need the functionality right now.
For zork and guybrush, this change is a no-op. eSPI is configured in
verstage which is located in RO, and we have already locked RO for
these devices. We will need to figure out how to properly set the
`vw_irq_polarity` for these devices.
BUG=b:218874489, b:160595155, b:184752352, b:157984427, b:238818104
TEST=On zork, guybrush and skyrim
$ suspend_stress_test --post_resume_command 'cat /sys/devices/platform/i8042/serio0/wakeup/wakeup35/active_count'
Verify keyboard works as expected and no interrupt storms are observed.
On morphius I verified keyboard and mouse work on windows as well.
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I4608a7684e34ebb389e0e55ceba7e7441939afe7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54924
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Change the SPL file from the 'cezanne' placeholder to a mendocino
filename. Also, move the default location to blobs/mainboard since
it's not board-agnostic.
BUG=b:241543152
BUILD=Enable feature and build amd/chausie
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Change-Id: I47647c5d926484e25e3f893e72c671554e277a56
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66465
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
|
|
Change the name of the whitelist file from the 'cezanne' placeholder
to a mendocino path/to/file. Also, as whitelist files won't be pushed
into a public repo, modify the path to point to site-local.
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Change-Id: I49bbf1335606567735e36ed9bda1314bfc6247d6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66464
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Modify sabrina's fw.cfg to point to the proper directory and use the
standard names, as released by AMD.
The name 'sabrina' was an alias used for the Mendocino product. The
public-facing builds have been using Cezanne blobs, renamed as Sabrina
or SBR, but can now take advantage of the appropriate blobs.
BUG=b:239072117
TEST=Build amd/chausie
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Change-Id: Id646844e41980802be1e39dce96e5adaace4311d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66463
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Boot issue while using FW slot A has been root-caused to the usage of
same TLB to map HW Crypto engines and SPI flash. With upcoming PSP
release, this TLB usage conflict has been resolved. Hence enable CCP
DMA.
BUG=b:240175446
TEST=Build and boot to OS in Skyrim with PSP verstage using CCP DMA.
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Change-Id: I2b12adb7e94e489bf07963a6f9a829cf4b36ad5c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66444
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Currently bootblock does not initialize eSPI if it is already done in
PSP verstage. But some other component is clobbering the eSPI
configuration causing timeouts in EC communication after the boot flow
hits x86. To workaround this issue, re-initialize eSPI in bootblock.
BUG=b:217414563
TEST=Build and boot to OS in Skyrim with PSP verstage.
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Change-Id: I41c0b2816a106a6a547f3cb372693e1bb7f23734
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66443
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I774be6d80e0aae725ecb1027501c8d66e0bf5a08
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66399
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
|
|
This function is only called from the same compilation unit, so turn it
into a static function.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I5c2deaa46f69c763df9612e39415b37c60d631be
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66398
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
|
|
Switching off the pads of the internal crystal oscillator that connect
to the crystal on the board in S0i3 saves a little power, so enable it.
No measurements to quantify the power savings have been made. PPR #57243
revision 1.59 was used as a reference.
BUG=b:237647468
TEST=None
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I52f14ae5c614ad8ff0479b619de7164afa1e7648
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66336
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
|
|
Add static check to ensure the reserved APOB DRAM space is the same size
as the MRC_CACHE region specified in the fmap.
Update sabrina APOB DRAM size to match the fmap.
TEST: Timeless builds identical. Test build with a larger MRC_CACHE than
APOB DRAM failed the assert as expected.
Signed-off-by: Fred Reitberger <reitbergerfred@gmail.com>
Change-Id: Ia14f6ef94b9062df0612fe96098b1012085ccf9c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/65878
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Sabrina"
This reverts commit 78261e308de5361b2ff045091e8fb18cad2a5035.
Reason for revert: Now that PSP supports a soft fuse flag to toggle the
verstage serial logs, prevent PSP verstage from writing to the UART.
BUG=None
TEST=Build and boot to OS in Skyrim with PSP verstage. Ensure that PSP
verstage logs are not seen twice in the console.
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Change-Id: I7ef2d585c320ea5903197939136dd2049a71af95
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66248
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
HW Modexp engine is verified to be working fine. Any verification
failures during PSP verstage are because the firmware body is not read
correctly. This might be because of the incorrect SPI ROM mapping. Hence
enable the HW modexp engine for keyblock, preamble and firmware body
verification.
BUG=b:240175446
TEST=Build and boot to OS in Skyrim with PSP verstage using one of the
FW slots.
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Change-Id: I8f6742630a7049354a24053fce28c477e53259e6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66247
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
Enabling them causes firmware keyblock/preamble and/or body verification
failure. Hence disabling them to use software based verification.
Re-enable them once the issue is root-caused.
BUG=b:217414563
TEST=Build and boot to OS in Skyrim with PSP and x86 verstage.
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Change-Id: I7e259ae5d790977d08afcb0a77f8d4f38c85f39e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66134
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Currently only SHA_GENERIC is used and does not need to be passed.
BUG=b:217414563
TEST=Build and boot to OS in Skyrim with PSP and x86 verstage.
Change-Id: Id705b1361fffaf940c51515e7f77d7fb0677fc4a
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66133
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
The SPI_RESTRICTED_CMD register is not a PCI configuration register. It
is memory mapped from the SPI bar.
Verified against PPR 55570 rev 3.16, PPR 56569 rev 3.03, and PPR 57243
rev 1.50
TEST=Compile tested only
Change-Id: I7c88aaea9ddac200644bb368be3bd4e9be47fd7b
Signed-off-by: Fred Reitberger <reitbergerfred@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63305
Reviewed-by: Martin Roth <martin.roth@amd.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
PSP expects PSP L2 directory address relative to the start of the SPI
ROM. Also PSP does not expect BIOS L2 directory address since it is an
entry in PSP L2 directory. Update the configuration such that PSP
verstage passes the right address to PSP.
BUG=b:217414563
TEST=Build Skyrim BIOS image. Ensure that PSP verstage passes the
address as expected by PSP.
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Change-Id: I8dc3aa4cb401d16a68da446f83eb9e68ee290fea
Reviewed-on: https://review.coreboot.org/c/coreboot/+/65866
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
On SoCs where PSP use A/B recovery layout, PSP expects PSP L2 directory
address relative to the start of the SPI ROM. Unfortunately there is
nothing in the EFS2 header to help identify such SoCs. Hence add a
config item to statically identify such SoCs.
Also when PSP uses A/B recovery layout, BIOS L2 directory is an entry in
the PSP L2 directory. Hence the address of BIOS L2 directory is not part
of EFS2 header. Thankfully PSP is able to identify the BIOS L2 directory
itself and does not expect PSP verstage to pass the address. Modify PSP
verstage to handle these updates.
BUG=b:217414563
TEST=Build Skyrim BIOS image. Ensure that PSP verstage returned the PSP
L2 directory as expected.
Change-Id: I2f856a62055c80b8e2db91c983832611a5f0389c
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/65865
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
PSP supports mapping FCH UART and verstage logs are visible in console.
Hence pre-bootblock cbmem contents do not have to be dumped to console.
BUG=b:238937687
TEST=Build Skyrim BIOS image. Ensure that PSP verstage logs in CBMEM are
not dumped to console again during bootblock.
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Change-Id: I8336e372b894d8b2f9bbfb21ab15a78527dcc4c4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/65863
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
Skyrim uses second SPI pads for ESPI. Switch to it initialize ESPI in
verstage.
BUG=b:217414563
TEST=Build Skyrim BIOS image. Ensure that ESPI init is successful in PSP
verstage.
Change-Id: I6e3462e95c50d256b6c159ae1d854dd69a538bb0
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/65862
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Martin L Roth <gaumless@tutanota.com>
|
|
Change-Id: I187c2482dd82c6c6d1fe1cbda71710ae1a2f54ad
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/64890
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
This allows the mainboard code to change FSP-M parameters depending on
parameters that are only known at run time and not at build time.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I3e0e196a5d861acd7635c59db44ecf1970b73ce2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/65855
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martin.roth@amd.corp-partner.google.com>
|
|
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Change-Id: Id56310bd616cd19fee5dc934676006b2dc34b1ff
Reviewed-on: https://review.coreboot.org/c/coreboot/+/65929
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Change-Id: Ibe20d48bdd8c776f9658620a13814f96e564dabc
Reviewed-on: https://review.coreboot.org/c/coreboot/+/65907
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Change-Id: I54438978db13ba00188e53239f7034d1b258e912
Reviewed-on: https://review.coreboot.org/c/coreboot/+/65900
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Change-Id: I7b6e41fa3b7cd8c8f7327c690212ec4990e8baf5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/65895
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
The APOB in sabrina is larger than in cezanne/picasso and no longer
fits in the previously allocated 64K space for it. Other symbols are
placed immediately after the APOB region and end up corrupting the APOB
data on sabrina.
Add a Kconfig option to specify the APOB size in DRAM to reserve enough
memory and increase the size for sabrina to 128K
TEST=Timeless builds are identical for mandolin/majolica for PCO/CZN.
Build chausie and verify symbols do not overlap _apob region
BUG=b:224056176
Signed-off-by: Fred Reitberger <reitbergerfred@gmail.com>
Change-Id: Ia5dbacae67ff02fc8a6ec84b9007110ca254daa3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/65852
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
This change is to allow AMD MP2 I2C OS driver to access
I2C0/1 devices when MP2 firmware is loaded.
Change-Id: Iaf25eb4dcf949e4b512ec0e86dbe5ccbc91c3d24
Signed-off-by: Ritul Guru <ritul.bits@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/65673
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This moves the die() statement to a common place.
Change-Id: I24c9f00bfee169b4ca57b469c089188ec62ddada
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/65812
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
This allows the compiler to optimize out code called after run_ramstage.
Also remove some die() statements in soc code as run_ramstage already
has a die_with_postcode statement.
Change-Id: Id8b841712661d3257b0dc67b509f97bdc31fcf6f
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/65811
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
Since there are many identifiers whose name contain "__unused" in
headers of musl libc, introducing a macro which expands "__unused" to
the source of a util may have disastrous effect during its compiling
under a musl-based platform.
However, it is hard to detect musl at build time as musl is notorious
for having explicitly been refusing to add a macro like "__MUSL__" to
announce its own presence.
Using __always_unused and __maybe_unused for everything may be a good
idea. This is how it works in the Linux kernel, so that would at least
make us match some other standard rather than doing our own thing
(especially since the other compiler.h shorthand macros are also
inspired by Linux).
Signed-off-by: Bill XIE <persmule@hardenedlinux.org>
Change-Id: I547ae3371d7568f5aed732ceefe0130a339716a9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/65717
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
This makes it easier to have common code for MP init on AMD systems.
Change-Id: Icb6808edf96a17ec0b3073ba2486b3345a4a66ea
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/64867
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
This avoids searching the HOB output multiple times when calling
smm_region().
Change-Id: Iad09c3aa3298745ba3ba7012e6bb8cfb8785d525
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/65787
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Change-Id: I73174766980e0405e7b8efd4f059bb400c0c0a25
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/64866
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Change-Id: Idd214893f304ce767633ffbf905f47a5092c2ee4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/65697
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Sabrina previously didn't support UART mapping in psp verstage. Now that it has been enabled, add the relevant uart code here.
BUG=b:218709292
TEST=Set serial soft fuse, boot to kernel, check logs
Signed-off-by: Jon Murphy <jpmurphy@google.com>
Change-Id: I591fa69b6e722929839babfff62e9d56c68e1112
Reviewed-on: https://review.coreboot.org/c/coreboot/+/65532
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Branding changes to unify and update Chrome OS to ChromeOS (removing the
space).
This CL also includes changing Chromium OS to ChromiumOS as well.
BUG=None
TEST=N/A
Change-Id: I39af9f1069b62747dbfeebdd62d85fabfa655dcd
Signed-off-by: Jon Murphy <jpmurphy@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/65479
Reviewed-by: Jack Rosenthal <jrosenth@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
|
|
This change adds new Rembrandt SoC support by defining it as base SoC
of sabrina as sabrina is derived from Rembrandt SoC.
All the needed changes for Rembrandt SoC will be applied under
SOC_AMD_REMBRANDT config.
Change-Id: I1c9392918cc2c6b511d467f99aceefc725750ce6
Signed-off-by: Ritul Guru <ritul.bits@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63353
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Reverting commit 1e25fd426ad8 ("soc/amd/common/block/psp: introduce
AMD_SOC_SEPARATE_EFS_SECTION").
A better solution was used in commit c17330c1dddb ("mb/amd/chausie: Add
EC blob into CBFS"), and this is no longer necessary.
TEST: Boot chausie
Signed-off-by: Fred Reitberger <reitbergerfred@gmail.com>
Change-Id: I27a8622a1f0d871690b181a79adca225a20996ea
Reviewed-on: https://review.coreboot.org/c/coreboot/+/65492
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
This replaces IORESOURCE_SUBTRACTIVE with IORESOURCE_RESERVE.
Change-Id: Ib3d934ca704273daacbeb3c52412bf04e2be7217
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/64695
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Return the correct processor family code for smbios per System
Management BIOS (SMBIOS) Reference Specification DSP0134 revision 3.5.0.
BUG=b:234409052
TEST=Boot chausie to chromeos and verify "dmidecode -t processor"
outputs the correct processor family.
Signed-off-by: Fred Reitberger <reitbergerfred@gmail.com>
Change-Id: I617ce3e23f4b28a197034756d285339595d3b53b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/65364
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Most of the src/soc/Kconfig files are only there for AMD and Intel to
load the main SoC Kconfig files before any common files. That can be
done in src/Kconfig instead. Moving the loads to the lower level allows
the removal of all but the Intel soc/Kconfig file, which can be removed
in a follow-on patch.
Signed-off-by: Martin Roth <gaumless@gmail.com>
Change-Id: I5061191fe23e0b7c745e90874bd7b390806bbcfa
Reviewed-on: https://review.coreboot.org/c/coreboot/+/65327
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
|
|
The common AMD ACPI GPIO access code is verified to be correct for
Sabrina.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I834076c0a1d1784a272896f2d8f082ebfb86a383
Reviewed-on: https://review.coreboot.org/c/coreboot/+/65317
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
The MCA banks were updated in commit 736d68c0b36e ("soc/amd/sabrina/mca:
update MCA bank names to match the hardware"), but seems that I forgot
to remove the TODO about checking if this is still correct for Sabrina.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ifd86113ccb9eeab704679afab0b985f9febed13b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/65314
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
