Age | Commit message (Collapse) | Author |
|
The RCOMP data group is special and is programmed differently. Prepare
to simplify the code by programming it outside of the loop. Subsequent
commits will simplify the logic even further, then clean up cosmetics.
The special DDR3 case in the loop overwrites the command group strength
multiplier value. It doesn't need to be programmed for each RCOMP group.
Add a comment to justify not programming this register while programming
the settings for the RCOMP data group.
Tested on Asus P5QL PRO (DDR2), still boots.
Change-Id: I5c2484f48e3c07e8e787b1894932e342e8e8a75c
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49398
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Change-Id: I84d5457173598e8ff41dfb048a6858b41c5692ac
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49397
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
These settings can be programmed with a single register write. Factor
the writes out into a single function to avoid some redundancy.
Tested on Asus P5QL PRO, still boots.
Change-Id: I3a08c255dd2b0deae650c7fe2ba4e1f4d1cef581
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49396
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
MRC uses an incorrect mask when programming this register, but the reset
default value is zero and it is only programmed once. As it makes no
difference, we can safely use the correct mask. Document this difference
in a comment to indicate the deviation from MRC behavior is intentional.
The default value for this register was dumped from Asus P5QL PRO.
Change-Id: I93b0c382f76e141b319414258e40a8bfe6c7848a
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49391
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Consistently use commas after the last element of arrays, and also align
columns of values and comments. Remove `MHz` units from DDR speed values
to avoid confusion, as the memory's actual clock speed is half of these.
Tested with BUILD_TIMELESS=1, Asus P5QL PRO remains identical.
Change-Id: Id13022483c6221ce87d21dd21a5cfe4317a55ccd
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49390
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Time has proven this statement to be unnecessary. Uncommenting it would
not have any effect on the existing code, thus remove it completely.
Change-Id: Iff4cdd71435e4fd69d4f3284e9fb2830fdd5b173
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49389
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
These accessors can be reused for several other northbridges.
Tested with BUILD_TIMELESS=1, Roda RK9 remains identical.
Change-Id: Ia16ccc63dddebf938f4e9a7f5518e4d25d3e7e66
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49748
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Drop casts to prevent pointer arithmetic and for consistency with other
platforms. These macros will be factored out in a subsequent commit.
Change-Id: I959e7378a8bf46fd1772192090a751d7a2f6f470
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49747
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Guarding the MCHBAR macro breaks reproducibility, but should not have
any functional impact.
Change-Id: I8be8d7b8a0f289d2be76d3dec43999f6b42e3265
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49746
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: Ief81d49f04c1743b2a37633c4a35da9d6ddb0974
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50039
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
It was commented that the need for the delay was mainly related
to external displays and only with VBIOS execution. Move the
delay such that it is done only when we actually need to execute
the VBIOS aka option rom.
A delay is currently only defined for librem/purism_bdw in
its Kconfig. As the description of the issue sounds like it
would equally happen on other platforms when VBIOS is involved,
promote the Kconfig visible option to global scope.
Change-Id: I4503158576f35057373f003586bbf76af4d59b3d
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48787
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Create `FIXED_RCBA_MMIO_BASE` and use it everywhere, except in cases
where a pointer cast would be necessary. Instances in Sandy Bridge MRC
code were left as-is intentionally, so as not to collide with another
cleanup patch train.
Tested with BUILD_TIMELESS=1, these boards remain identical:
- Asus P8Z77-V LX2
- Packard Bell MS2290
Change-Id: I642958fbd6f02dbf54812d6a75d6bc3087acc77a
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50036
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This partially reverts:
- Commit 77d3b655ed
- Commit 487c1a24f5
- Commit 875c21f491
- Commit c4d1b47ad9
- Commit b96c358751
- Commit 9cbf26d18e
It is intentional to use <device/pci_ops.h> whenever one needs to use
PCI config access. The bootblock.c files needing I/O config do not need
to be an exception to this.
Change-Id: Ifba05717dad404a844618815c5347a05e07a3362
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50231
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
|
|
Change-Id: Ide5673dc99688422c5078c8c28ca5935fd39c854
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50186
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Change-Id: I3dafffa61f4fe6089fd11ef6579626aff8088df5
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50185
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Change-Id: Ide960d7957e8a95961ec3722ad7478926a84c544
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49538
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Also replace 'reg' with 'reg32'.
Change-Id: I2aa8862de0f7629386ef09acbb0606056cc3697c
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49537
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: Ib370fc1bae017d084844eece44799676a657323b
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49541
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Also rename 'reg' to 'reg32'.
Change-Id: Id741f636162a8a228bca069637993422deb5e09c
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49535
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Also rename 'reg' to 'reg32'.
Change-Id: Ie8dd238a8f10daad9653f44b3ada329c3ede58fe
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49536
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Also rename 'reg' to 'reg32'.
Change-Id: I3aca03dfe20dd0a61cba3ba55146f76e412a2c5e
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49540
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
They aren't necessary. Removing them changes the binary because the
corresponding access macros no longer perform pointer arithmetics.
Change-Id: I9723a00b58ee35befdce6a3a51aa2b1fce8efa80
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49745
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Done for consistency with other northbridges.
Change-Id: I08023809477c1cef0d7762b5e4fde65fadf6a6d8
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46991
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
|
|
Taken from Broadwell.
Change-Id: I246fdc1473bf8949073377d03622026bd3e6aafa
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46990
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
|
|
Change-Id: I5c75409fd3b7b018e402c471cbd856eca20278b7
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49757
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I635f3615f566502f79bbd81f9f743ce63bba3b1a
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49758
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Note that bootblock.c originally wrote a reserved bit of the PCIEXBAR
register. The `length` bitfield was set to 0, so assume 256 busses.
Moreover, the ASL reservation for MMCONFIG was only for 64 busses.
Change-Id: I7366a5096aacd92401535be020358447650b4247
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49759
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Note that bootblock.c originally wrote a reserved bit of the PCIEXBAR
register. The `length` bitfield was set to 0, so assume 256 busses.
Change-Id: Ie967747b4bf559b5aedc67cbcd35bca51f5a692e
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49760
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Bootblock enabling needs some special handling. Also, the definition of
the `get_pcie_bar` function is incorrect for Ironlake, so remove it.
With this patch, using 64 and 128 for MMCONF_BUS_NUMBER should work.
However, it has not been tested. Using 256 busses should still work.
Change-Id: Ic466ddc7b80f60af5cbff53583281440f02974c7
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49761
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: Id88c18129bb773d979ad84bd0bb47188d74d4bc4
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49762
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I0d6338f763a78895b1ae14d1ab68253851b6c283
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49763
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Use defined RCBAx macros over readX/writeX calls.
Tested with BUILD_TIMELESS=1, Packard Bell MS2290 remains identical.
Change-Id: I87cae75268ef5f329001706e4771e98653d40cd1
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50037
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Only specify the type of MMCONF_BASE_ADDRESS and MMCONF_BUS_NUMBER once.
Change-Id: Iacd2ed0dae5f1fb6b309124da53b3fa0eef32693
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50032
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Avoid indirect header inclusion, include `pch.h` where necessary.
Change-Id: I6b72976a28ffaad68bcf558c8a13b5c221070522
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49944
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
|
|
Use the same variable name as soc/intel to implement a common
_PIC method at top-level ASL.
Change-Id: I48f9e224d6d0101c2101be99cd18ff382738f0dd
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49903
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
All callsites of `rmw_1d0` use the same `flag` value.
Change-Id: I84fab5d3fd270ce684cd6ca892c213b0d8610283
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49578
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
|
|
Reference code does not run any DMI recipe for Sandy Bridge. Create a
helper function and exit early for Sandy Bridge. The CPUID value will
be used in a follow-up, since DMI setup has stepping-specific steps.
Change-Id: I5d7afb1ef516f447b4988dd5c2f0295771d5888e
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48413
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Based on reference code, update the DMI ASPM setup steps.
Change-Id: I1248305b2f76f48f4e6910de1a6980e942f16945
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48536
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Backport commit ab7586fa26 (broadwell: Set C9/C10 vccmin) to Haswell.
Change-Id: I9cddc7dd45e96c6f99327ee2583917bf8bedfbdd
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46922
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Increase DCACHE_RAM_SIZE to 32kB and remove "NO_CBFS_MCACHE".
It’s quite safe to increase DCACHE_RAM_SIZE. All LGA775 targets
should have at least 256K L2 cache. That is plenty for XIP RO cache of
bootblock + romstage and a 32K CAR.
Change-Id: I393b2727bd90a990c3108a4dbead62b17d7fc531
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49505
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Fixed resources should not overlap.
Change-Id: I166e0095ac0cc0dd8271a693bb452f505a1a9413
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49626
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
This cosmetic change does 2 things:
- change bitwise shifting to division
- Make the division by / KiB explicit for fixed legacy ranges like
0xa0000.
Change-Id: Ia6c2ee29e37040ea9b11505e9888c7f6f8da78bc
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49625
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
This memory is used for option roms and BIOS. This matches the ACPI
code.
Change-Id: I53dd4b967569889108352ca70086a12ce252e8e0
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49624
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
This cosmetic change does 2 things:
- change bitwise shifting to division
- Make the division by / KiB explicit for fixed legacy ranges like
0xa0000-0xbffff.
Change-Id: I626989fa6625e0b3613a11e709c614d40a788b0e
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49623
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Fixed resources should not overlap.
Change-Id: I7a70f5475c1d701db2cb8cbea659bacf6d0c52ae
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49622
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
This cosmetic change does 2 things:
- change bitwise shifting to division
- Make the division by / KiB explicit for fixed legacy ranges like
0xa0000-0xbffff.
Change-Id: If4e05f496abc05e06a944b244824376f3937a57b
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49621
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Change-Id: Ic5a49a81a886aecde0fbaae3ecfa6b0504a4e3ec
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49620
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Change-Id: Ic2582dbf70e11e0566ba525c72300a6248807512
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49619
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Given the lack of documentation for this platform, having this info
in coreboot logs (e.g. from board_status) can be pretty useful.
Change-Id: I6a743c1efc1b6da71589460a69bfe4785e3e77a2
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49576
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
It looks like we didn't care to reserve the VGA MMIO (a & b segments)
and the c..f segments, initially. It was probably never needed until
the new resource allocator that will make use of any unclaimed space.
Change-Id: Iebdae64914d9f8301cafc67a5aba933c11294707
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49603
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
This reverts commit 27af8a7e5df435d93547061a3273ec4de45f0080.
Reason for revert: This depends on CB:45517 which hasn't landed yet.
Change-Id: I2a6fbf54cfe01bf25e9ea8da84f6f2a17418f0ae
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49647
Tested-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Change-Id: Iee24c6bf82ab6ff6691707ed0c388cfe492cc925
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49523
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Change-Id: Ie3bfdb27aa7c981a500e82b6a6958576e0048bcd
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49532
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jacob Garber <jgarber1@ualberta.ca>
|
|
Change-Id: I9763499ad5cf0395c83770908a277f089ceed475
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49530
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jacob Garber <jgarber1@ualberta.ca>
|
|
Change-Id: I9e723e1d31b093a4781413efe7f290a295b833dc
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49524
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jacob Garber <jgarber1@ualberta.ca>
|
|
Change-Id: Iabd6c69cd4c28f0015d4cf1f95d5ae0b6dc8b47e
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49568
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jacob Garber <jgarber1@ualberta.ca>
|
|
For a long time, second parameter 'stop' has been
ignored. The tested range is within 1 MiB above 'start'.
Change-Id: Icbf94cd6a651fbf0cd9aab97eb11f9b03f0c3c31
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48561
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Command timing is the absolute value of the most negative `pi_coding`
value across all ranks, or zero if there are no negative values. Use the
MAX() macro to ease proving that `cmd_delay` can never be negative, and
then drop the always-false underflow check.
The variable type for `cmd_delay` still needs to be signed because of
the comparisons with `pi_coding`, which is a signed value. Using an
unsigned type would result in undefined and also undesired behavior.
Change-Id: I714d3cf57d0f62376a1107af63bcd761f952bc3a
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49320
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Clock is a differential signal and propagates faster than command and
control, therefore its timing needs to be offset with `pi_code_offset`.
It is also a periodic signal, so it can safely wrap around.
To avoid potential undefined behavior, make `clk_delay` signed. It makes
no difference with valid values, because the initial value can be proven
to never be negative and `pi_code_offset` is always positive. With this
change, it is possible to add an underflow check, for additional sanity.
Change-Id: I375adf84142079f341b060fba5e79ce4dcb002be
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49319
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Commit 7584e550cc (nb/intel/sandybridge: Clean up program_timings)
introduced this condition along with a comment that says the opposite.
Command and clock timings always need to be computed, so drop both the
nonsensical condition and the equally-worthless corresponding comment.
Change-Id: I509f0f6304bfb3e033c0c3ecd1dd5c9645e004b2
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49318
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Use C-style comments everywhere, and follow the coding style.
Tested with BUILD_TIMELESS=1, Asus P5QL PRO remains identical.
Change-Id: I3ef96c5f6553ad50cee7d7f5614128b62a89e4ea
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49387
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Eaglelake MRC 2.55 does this, and also stalls for less time.
Change-Id: Iaaefd32c341a490e5c129df865407ec3f8da8212
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49385
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
To allow other platforms to reuse this code, extract it into a separate
compilation unit. Since HPET is enabled through the southbridge, place
the code in the southbridge scope. Finally, select the newly-added
Kconfig option from i82801gx and replace lpc.c `enable_hpet` function.
Change-Id: I7a28cc4d12c6d79cd8ec45dfc8100f15e6eac303
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49365
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Add brackets around the parameters to avoid operation order problems.
Tested with BUILD_TIMELESS=1, Roda RK9 remains identical.
Change-Id: I023bb116fa2bdcaa7cfdce2445513da3959e827d
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45435
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Wrap `r` in parentheses to avoid unexpected behavior with compound
expressions. This prevents `CxDRBy_BOUND_MB(r+1, base)` from triggering
undefined behavior when `r = 2`, as the shift would be greater than 32.
Change-Id: I14235b2708ab502d842da677451c14203a469b45
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49261
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Sort MSR definitions, move MCHBAR registers to northbridge and relocate
C-state latency macros into the header.
Tested with BUILD_TIMELESS=1, Asrock B85M Pro4 remains identical.
Change-Id: I3b02f1b1eff522c037e6fc8bb0d831423913da29
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46914
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: Iacb1fb0a1309c3c23e670fee540514b6f546314a
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49066
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
|
|
To allow adjusting the phase shift of the various I/O signals, the
memory controller contains several PIs (Phase Interpolators). These
devices subdivide a QCLK (quarter of a clock cycle) in 64 `ticks`,
and the desired phase shift is specified in a register. For shifts
larger than one QCLK, there are `logic delay` registers, which allow
shifting a whole number of QCLKs in addition to the PI phase shift.
The number of PI ticks in a QCLK is often used in raminit calculations.
Define the `QCLK_PI` macro and use it in place of magic numbers. In
addition, add macros for other commonly-used values that use `QCLK_PI`
to avoid unnecessarily repeating `2 * QCLK_PI`, such as `CCC_MAX_PI`.
Tested with BUILD_TIMELESS=1, Asus P8Z77-V LX2 does not change.
Change-Id: Id6ba32eb1278ef71cecb7e63bd8a95d17430ae54
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49065
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Drop unused definition and remove outdated comments.
Change-Id: I16033b558fe4c01a9394382dc0c9d0bdc66193d9
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46993
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
|
|
There's no need to use `memset` here.
Change-Id: I0478bc3ff25b75bf0b554aa83ead6a63fcbd975c
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49064
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
There are multiple different devicetree setting formats for graphics
panel settings present in coreboot. Replace the ones for the platforms
that already have (mostly) unified gma/graphics setup code by a unified
struct in the gma driver. Hook it up in HSW, BDW, SKL, and APL and adapt
the devicetrees accordingly.
Always ensure that values don't overflow by applying appropriate masks.
The remaining platforms implementing panel settings (GM45, i945, ILK and
SNB) can be migrated later after unifying their gma/graphics setup code.
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Change-Id: I445defe01d5fbf9a69cf05cf1b5bd6c7c2c1725e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48885
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
For easier review of the switch to a new register struct in the
follow-up change, the panel delay times get converted from destination
register raw format to milliseconds representation in this change.
Formula for conversion of power cycle delay:
gpu_panel_power_cycle_delay_ms =
(gpu_panel_power_cycle_delay - 1) * 100
Formula for all others:
gpu_panel_power_X_delay_ms = gpu_panel_power_X_delay / 10
The register names gain a suffix `_ms` and calculation of the
destination register raw values gets done in gma code now.
Change-Id: Idf8e076dac2b3048a63a0109263a6e7899f07230
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48958
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
which select INTEL_GMA_ACPI. Rework brightness level includes and
platform-level asl files to avoid duplicate device definition for GFX0.
Include gfx.asl for Skylake/Kabylake, since all other soc/intel/common
platforms already do. Adjust mb/51nb/x210 to prevent device redefinition.
Some OSes (e.g. Windows, MacOS) require/prefer the ACPI device for
the IGD to exist, even if ACPI brightness controls are not utilized.
This change adds a GFX0 ACPI device for all boards whose platforms
select INTEL_GMA_ACPI without requiring non-functional brightness
controls to be added at the board level.
Change-Id: Ie71bd5fc7acd926b7ce7da17fbc108670fd453e0
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48862
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
|
|
Correct the mask for the power cycle delay from 0xff to 0x1f, to
represent the actual maximum value according to Intel graphics PRM for
Haswell, Volume 2c and Intel graphics PRM for Broadwell, Volume 2c.
Change-Id: Ib187f1ca6474325475e5ae4cc1b2ffbce12f10bf
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48957
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
src/northbridge/amd/pi/00660F01/Kconfig does not exist. Remove the
source statement.
Also, no kconfig files under src/soc/intel/common/basecode/. Clean
that up.
Signed-off-by: Jack Rosenthal <jrosenth@chromium.org>
Change-Id: I10917b76ff6c2a9d5a97d5c7dfa9e8925cd8c8a4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48676
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
The Sandy Bridge steppings appear in the BWG, and Ivy Bridge steppings
appear in reference code. Add them for the sake of completeness.
Change-Id: I7d17cdd04a771ca319c908fc757f868e95ea7944
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48410
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
|
|
The steppings correspond to the CPUID bits 3:0, so move them to the CPU
scope, and include the CPU header from files using the stepping macros.
Change-Id: Idf8fba4911f98953bb909777aea57295774d8400
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48409
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Rewrite some constants to make their meaning somewhat clearer.
Tested with BUILD_TIMELESS=1, Asus P8Z77-V LX2 does not change.
Change-Id: I321f5e61d7c695ae77e61b84728e34930f69d400
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48615
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Native raminit only supports 1.5V operation, but there are DIMMs which
request 1.65V operation in XMP profiles. Add an option to force XMP to
be used when the requested voltage isn't supported, which will run the
DIMMs at 1.5V with XMP timings. Consider this to be overclocking.
Change-Id: I64bfac8f72dadf662ceadfc7998daf26edf5a710
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48614
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Leverage existing `ch_dimms` value and use constants for brevity.
Change-Id: I4e08166c8e9fbd15ff1dcd266abb0689e4b159f7
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48613
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Pointers to structs can be very useful, especially when they point to an
array element. In this case, changing one pointer allows the function to
be rewritten more concisely, since most redundancy can be eliminated.
Tested on Asus P8Z77-V LX2, still boots. No functional difference.
Change-Id: I7f0c37ea49db640f197162f371165a6f8e9c1b9c
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48612
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Ensure that IOSAV is finished before continuing. This might solve some
random failures on the I/O and roundtrip latency training algorithm.
Tested on Asus P8Z77-V LX2, still boots.
Change-Id: Ic08a40346b6c60e372bada10f9c4ee42eb974f9f
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48403
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Most ofte, `iosav_run_once` precedes a `wait_for_iosav` call. Add a
helper function to reduce clutter. The cases where `iosav_run_once`
isn't followed by `wait_for_iosav` will be handled in a follow-up.
Tested on Asus P8Z77-V LX2, still boots.
Change-Id: Ic76f53c2db41512287f41b696a0c4df42a5e0f12
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48402
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
These comments were helpful before the massive IOSAV refactoring, but
they are no longer needed since the function names are clear enough.
Change-Id: Ieb9bdf3f7fc72f63a8978f2b98e0bc8228c55868
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48401
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Print delay values in a suitable format for human consumption.
Change-Id: I0d86187d3e458ee2cb3fd11ec896ac363b8d3249
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48400
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I164daa59696f2fe8de3a4b3e7da46c7c723778eb
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48602
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Now that the purpose of each training algorithm is clear, replace the
last instances of the original names in comments and print statements
with the current, correct names. Also, print which channel has failed
command training, for completeness and consistency with other errors.
Change-Id: I9cc5c4b04499297825ca004c6bd1648a68449d2c
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48601
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Document the algorithm to adjust I/O and roundtrip latencies.
Change-Id: Ic8b9aed54a34bb3252c457e87e81387fd410e305
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48397
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Tested on Asus P8H61-M PRO, still boots.
Change-Id: I147ba0ade8a5317a0fe76e9ea84947fd91d794b4
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47773
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Refactor in preparation to split up `program_timings`.
Tested on Asus P8Z77-V LX2, still boots.
Change-Id: I68410165f397d8b4f662e40e88fb6a58ab1c5cff
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47772
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Use absolute values for the Rx and Tx bus timings instead of values
relative to the CA (Command/Address) bus timing. This makes the
calculations more accurate, less complex and less error-prone.
Tested on Asus P8H61-M PRO, still boots. Training results do not seem to
be affected by this patch, and the margins roughly have the same shape.
Change-Id: I28ff1bdaadf1fcbca6a5e5ccdd456de683206410
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47771
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Currently it's not possible to add multiple graphics driver into
one coreboot image. This patch series will fix this issue by providing
a single API that multiple graphics driver can use.
This is required for platforms that have two graphic cards, but
different graphic drivers, like Intel+Aspeed on server platforms or
Intel+Nvidia on consumer notebooks.
The goal is to remove duplicated fill_fb_framebuffer(), the advertisment
of multiple indepent framebuffers in coreboot tables, and better
runtime/build time graphic configuration options.
Replace set_vbe_mode_info_valid with fb_add_framebuffer_info or
fb_new_framebuffer_info_from_edid.
Change-Id: I95d1d62385a201c68c6c2527c023ad2292a235c5
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39004
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
|
|
Change-Id: I3e60cfc1fd3352b8b0c7460503179425cc593d36
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48589
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Change-Id: I0a32295e72270cde2e9bd2f8f00358b47ffd3e33
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48562
Reviewed-by: Christian Walter <christian.walter@9elements.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Clarify the clock, command and control programming sequence.
Tested on Asus P8Z77-V LX2, still boots.
Change-Id: I1aa4144197dc25dc8d6ef1d23e465280bddd95a3
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47770
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Do not combine the host bridge device ID with the CPU stepping because
it is confusing. Although Sandy/Ivy Bridge processors incorporate both
CPU and northbridge components into the same die, it is best to treat
them separately. Plus, this change enables moving CPU stepping macros
from northbridge code into the CPU scope, which is done in a follow-up.
Change-Id: I27ad609eb53b96987ad5445301b5392055fa4ea1
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48408
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Commit 7f1363d9b4 (nb/intel/sandybridge: Program MR2 shadow register)
has a bug where the system locks up and power cycles when booting Linux,
but is still able to pass memtest86+ with flying colors. The issue will
occur when the following conditions are true:
- CPU is Ivy Bridge
- Memory speed is not greater than 1066 MHz (DDR3-2133 or slower)
- System contains dual-rank DIMMs
- The second rank of the dual-rank DIMMs is mirrored
- All DIMMs support Extended Temperature Range
- At least one of the DIMMs does not support Auto Self-Refresh
If all of these conditions are met, the final value of the MR2 Shadow
registers configures the memory controller to issue a MRS command to
update MR2 before entering self-refresh mode, but indicates that rank
mirroring is not required (the first rank on a DIMM is never mirrored).
Before the memory controller enters self-refresh, it sends MRS commands
to all ranks to update MR2, but the missing address and bank mirroring
means DRAM chips on mirrored ranks instead clobber MR1 with junk data.
With garbage in MR1, the mirrored ranks no longer function properly,
which ultimately leads to all hell breaking loose (undefined behavior).
The condition is backwards, since only odd ranks can be mirrored. To
avoid this problem completely, simply remove the condition. The final
register value will still be correct, since the bits are always ORed.
Tested on Asus P8Z77-V LX2, fixes booting Linux with dual-rank DIMMs.
Change-Id: Iceff741eb85fab0ae846e50af0080e5ff405404c
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48550
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
|
|
Move all memory map definitions into a separate header.
Tested with BUILD_TIMELESS=1, Packard Bell MS2290 remains identical.
Change-Id: I1f37ad9cae39041f98871c613b308b5ac5da01b3
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45379
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
There's no need to wrap these macros with casts. Removing them allows
dropping more casts in `early_init.c`.
To avoid binary changes the casts are put into the
{MCH,DMI,EP}BAR{8,16,32} macros instead where they are needed to reach
the right memory locations.
Change-Id: Icff7919f7321a08338db2f0a765ebd605fd00ae2
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45378
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Inspired by Idca25b2e4bf65abcb and Ib275f9ad8ca9ff move all memory map
definitions into a header with a common name.
Change-Id: I32a99f70f4d2eb52367c9edfc0aa6d5da2fec03f
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48234
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|