| Age | Commit message (Collapse) | Author |
|---|
|
Add camera support in devicetree.
BUG=b:190797339
BRANCH=None.
TEST=built pirika firmware and verified camera function is OK.
Change-Id: I66ded32105f3166e2faec3ea5dcfb93c29822366
Signed-off-by: Alex1 Kao <alex1_kao@pegatron.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55450
Reviewed-by: Kirk Wang <kirk_wang@pegatron.corp-partner.google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
In order to meet timing requirement of WWAN reseting it in early GPIOs
and asserting Reset GPIO in ramstage
BUG=b:180166408
TEST=Build and boot Brya system and verify enumeration of L850 and FM350 devices
Signed-off-by: Varshit Pandya <varshit.b.pandya@intel.com>
Change-Id: Id6d69696b6c645eec3fa314a608c69214bafba82
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54912
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Fix build failures in the case <vc/.../chromeos.h> is removed.
Change-Id: Ie45066f39cd6fb92cca697a6bd5bc8bb8c60b4e7
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55506
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
APIC Serial Bus pins were removed with ICH5 already, so a choice
'irq_on_fsb = 0' would not take effect. The related register BOOT_CONFIG
0x3 is also not documented since ICH5.
For emulation/qemu-q35 with ICH9 the choice INTERRUPT_ON_APIC_BUS was
wrong and ignored as BOOT_CONFIG register emulation was never implemented.
For ICH4 and earlier, the choice to use FSB can be made based on the
installed CPU model but this is now just hardwired to match P4 CPUs of
aopen/dxplplusu.
For sb/intel/i82371eb register BOOT_CONFIG 0x3 is also not defined
and the only possible operation mode there is APIC Serial Bus, which
requires no configuration.
Change-Id: Id433e0e67cb83b44a3041250481f307b2ed1ad18
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55257
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This a mainly a preparation for adding the MMIO UART devices to the
chipset devicetree.
TEST=none
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I533e4a909fdeb1614dbc5df015440b9df5d83233
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55544
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I06102f4fcc3bf9de332c71a52c632241b95cde19
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55543
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
The BMC EEPROM layout has been updated to contain system and mainboard
serial numbers. Use these values in SMBIOS Type 1 and Type 2 tables.
Change-Id: I55b51a856b4ad28fd56b02015b2e1d49cd629735
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55275
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Use hostbridge.asl from Haswell instead of Broadwell. Both files are
equivalent. Then, drop the now-unused hostbridge.asl from Broadwell.
Tested with BUILD_TIMELESS=1, Purism Librem 13 v1 remains identical.
Change-Id: I87d51727b75a9c59e2f5f3ba8d48c575ce93c78c
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55484
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Mainboard information can be found in the included documentation.
Signed-off-by: Bill XIE <persmule@hardenedlinux.org>
Change-Id: Ic811e24bd72da84e5ca8f5b09f2eb65872153b72
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55111
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Disable all display related UPDs if IGD is not enabled as FSP
don't need to perform display port initialization while IGD itself
is disabled else assign UPDs based on devicetree config.
TEST=Dump FSP-M display related UPDs with IGD enable and disable
to ensure patch integrity.
Change-Id: I0479904141dfc5e707679109aa18b7ef4264cf96
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55273
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Add support for the ThinkPad W541 based on Peter Lemenkov's initial W541
port. Compiled and tested with SeaBIOS and Tianocore booting into Arch
Linux 5.10.32-lts. The Haswell mrc.bin blob is required.
Tested working:
- SATA SSD
- SATA DVD drive
- M.2 SATA
- All USB ports
- SD card reader
- Speakers/headphone jack
- Keyboard/touchpad
- libgfxinit
- VGA
- mini DisplayPort (Thunderbolt untested)
- eDP laptop screen
- NVIDIA GPU in Linux
- Camera/Mic
- Smartcard reader
- Internal flashing when IFD is unlocked
- ThinkPad basic dock (VGA, USB, Ethernet)
- CMOS options
- WLAN
- Bluetooth
- Ethernet
- Using me_cleaner
- All DDR3 slots
Not working:
- Keyboard backlight
- First boot can take up to 20s (MRC.bin is slow)
Untested:
- Thunderbolt
- Internal flashing when IFD is locked
- Other ThinkPad docks (DisplayPort, DVI, Audio)
- ExpressCard slot
- Battery thresholds
- WWAN card
- Fingerprint reader
- USB Debug console
Signed-off-by: Justin Wu <amersel@runbox.me>
Change-Id: Ia43070f51bba3cf59ba9b7d9e29e4e778efbeb08
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52659
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Peter Lemenkov <lemenkov@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change GPP_B2 (EN_PP3300_SSD) to PLTRST to avoid S3 resume hang.
BUG=b:174776411
BRANCH=none
TEST=none
Change-Id: I18ee085cde0570ef278ea3869be30471ed04e3db
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55446
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Change GPP_B2 (EN_PP3300_SSD) to PLTRST to avoid S3 resume hang.
BUG=b:174776411
BRANCH=none
TEST=none
Change-Id: Icfde6b57ff5f6e49ff7804eff6e6a5819bb784bc
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55445
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Change GPP_B2 (EN_PP3300_SSD) to PLTRST to avoid S3 resume hang.
BUG=b:174776411
BRANCH=none
TEST=none
Change-Id: Ib0858afa1b5dc9de9db87485d3e0bf6032416746
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55444
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Change GPP_B2 (EN_PP3300_SSD) to PLTRST to avoid S3 resume hang.
BUG=b:174776411
BRANCH=none
TEST=none
Change-Id: I19b5e1c4beebbc1ebd3d2e30bc22e8c890aaf78f
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55443
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Change GPP_B2 (EN_PP3300_SSD) to PLTRST to avoid S3 resume hang.
BUG=b:174776411
BRANCH=none
TEST=none
Change-Id: I7d35c284b88b8828d31fff9ccafeb914542b0837
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55442
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Change GPP_B2 (EN_PP3300_SSD) to PLTRST to avoid S3 resume hang.
Add GPP_B2 to the early_gpio_table.
BUG=b:174776411
BRANCH=none
TEST=none
Change-Id: If8c253236051f6d170fab444cfc166e5d2ed7bc2
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55441
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Change GPP_B2 (EN_PP3300_SSD) to PLTRST to avoid S3 resume hang.
Add GPP_B2 to the early_gpio_table.
BUG=b:174776411
BRANCH=none
TEST=none
Change-Id: I49f7b1b69c3c3ab5593c7230d8f631a3b54c9c9d
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55440
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Change GPP_B2 (EN_PP3300_SSD) to PLTRST to avoid S3 resume hang.
Add GPP_B2 to the early_gpio_table.
BUG=b:174776411
BRANCH=none
TEST=none
Change-Id: I1214246bb1318869e9b6f57cb6a7e74bbe6574cc
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55439
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Change GPP_B2 (EN_PP3300_SSD) to PLTRST to avoid S3 resume hang.
Add GPP_B2 to the early_gpio_table.
BUG=b:174776411
BRANCH=none
TEST=none
Change-Id: Ifb6b5b14cec9e6f7c68aa9b01621fdb21c885552
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55438
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Change GPP_B2 (EN_PP3300_SSD) to PLTRST to avoid S3 resume hang.
Add GPP_B2 to the early_gpio_table.
BUG=b:174776411
BRANCH=none
TEST=none
Change-Id: I07be950096aef42dbf4f067134e56c5849dfa02d
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55433
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Change GPP_B2 (EN_PP3300_SSD) to PLTRST to avoid S3 resume hang.
BUG=b:174776411
BRANCH=none
TEST=none
Change-Id: Ia7db2d0a1fff98d1cfb8e7e979c0a81b9f3d0e9e
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55432
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
The system will hang when resuming from S3 if the SSD reset gpio is not
reset early enough.
Change GPP_A11 in baseboard to PLTRST to avoid an S3 resume hang.
BUG=b:174776411
BRANCH=none
TEST=none
Change-Id: Ia78d813cb6bc689b07e8d8ead1ade6e77f925ce1
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55431
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
The same functionality can be provided through a runtime-generated SSDT.
The remaining parts of device NVS are removed in a follow-up.
Since the SSDTs are only loaded after the DSDT (if loaded at all), using
SSDT-provided objects outside method bodies is not possible: the objects
are not yet in OSPM's ACPI namespace, which causes in ACPI errors. Owing
to this, the operation regions used by the _PS0 and _PS3 methods need to
be moved into the SSDT, as they depend on the SSDT-provided BAR1 values.
Tested on out-of-tree Compal LA-A992P, generated SSDT disassembles with
no errors and contains expected values. Linux does not complain either.
Change-Id: I89fb658fbb10a8769ebea2e6535c45cd7c212d06
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52520
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Add support for Maple Ridge DDR5 SKU with boardid 0x16
TEST=Verified build for ADL-P Chrome RVP
Signed-off-by: Deepti Deshatty <deepti.deshatty@intel.com>
Change-Id: I9f0e9072f5866b60fb8463bb90f61915c78568db
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52760
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Meera Ravindranath <meera.ravindranath@intel.corp-partner.google.com>
Reviewed-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-by: V Sowmya <v.sowmya@intel.com>
|
|
Many more asus boards using Panther Point PCH other than Z77 can be
added as variants of this series.
Signed-off-by: Bill XIE <persmule@hardenedlinux.org>
Change-Id: I3e0b5734658912a69ccde94d530399059502c4c4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55110
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Mainboard information can be found in the included documentation.
Signed-off-by: Bill XIE <persmule@hardenedlinux.org>
Change-Id: Ic56ac0e5f93a6e818ef0666e41996718471b1cf6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54338
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Set register "generic.stop_delay_ms" to 150 to reduce power resume time.
BUG=b:185308246
TEST=tested on voema
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Change-Id: Idd90191ee7ecbbc544121dc0b93101bea64f0e5f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54275
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add SPD support to elemi for MT40A512M16TB-062E:R
BUG=b:190020997
TEST=FW_NAME=elemi emerge-volteer coreboot chromeos-bootimage
Change-Id: I548ea2ec01dd0a43442a691cf870c2bc1b58bc74
Signed-off-by: Wisley Chen <wisley.chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55165
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
|
|
This is the same settings as voxel.
BUG=None
TEST=FW_NAME=trondo emerge-volteer coreboot chromeos-bootimage
Verify that the image-trondo.bin is generated successfully.
Change-Id: I04df68ce1683fa32195df1a93f5bde2e3efe6090
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54274
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
|
|
Create the gimble variant of the brya0 reference board by copying
the template files to a new directory named for the variant.
(Auto-Generated by create_coreboot_variant.sh version 4.5.0).
BUG=b:190334274
BRANCH=None
TEST=util/abuild/abuild -p none -t google/brya -x -a
make sure the build includes GOOGLE_GIMBLE
Change-Id: If425571d95b3b20910f890428fb5726ebad2fdf4
Signed-off-by: Mark Hsieh <mark_hsieh@wistron.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55300
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
`GFX_GMA_PANEL_1_ON_EDP` already defaults to `y` on Sandy Bridge.
Change-Id: I481754dc4f086469216c6e939c77b3c84bebea08
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55391
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Evgeny Zinoviev <me@ch1p.io>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Create the scout variant of the puff reference board by copying
the template files to a new directory named for the variant.
(Auto-Generated by create_coreboot_variant.sh version 4.5.0).
BUG=b:187080143
BRANCH=None
TEST=util/abuild/abuild -p none -t google/hatch -x -a
make sure the build includes GOOGLE_SCOUT
Signed-off-by: Jeff Chase <jnchase@google.com>
Change-Id: I3be9d2d30821c2c9132ed94c9faf1f33b62bbc7e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55173
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Kangheui Won <khwon@chromium.org>
|
|
Regenerate SPD for MT53E1G32D2NP-046 WT:B with correct value of ranks.
BUG=b:190692797
TEST=Build and boot to OS
Signed-off-by: Ivy Jian <ivy_jian@compal.corp-partner.google.com>
Change-Id: Icee095c7114f1d6dd960f2134db3816b367bf987
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55384
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Split parameter '(devfn << 2) | intx' to 'devfn, intx'.
Formatted with 'spatch --max-width 96'
Change-Id: I17a6b3919b6e55aaa7ca2873ca713b36ebe7d3a6
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55285
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Read I/O APIC ID and version from hardware registers.
With coccinelle below, and minor fixups.
@ r1 @
expression E1, E2, E3, E4;
typedef u8;
@@
-smp_write_ioapic(E1, E2, E3, E4);
+u8 ioapic_id = smp_write_ioapic_from_hw(E1, E4);
@ r2 @
expression E1, E2, E3, E4;
@@
-mptable_add_isa_interrupts(E1, E2, E3, E4)
+mptable_add_isa_interrupts(E1, E2, ioapic_id, E4)
@ r3 @
expression E1, E2, E3, E4, E5, E6, E7;
@@
-smp_write_pci_intsrc(E1, E2, E3, E4, E5, E6, E7)
+smp_write_pci_intsrc(E1, E2, E3, E4, E5, ioapic_id, E7)
@ r4 @
symbol mp_INT;
expression E1, E3, E4, E5, E6, E7;
@@
-smp_write_intsrc(E1, mp_INT, E3, E4, E5, E6, E7)
+smp_write_intsrc(E1, mp_INT, E3, E4, E5, ioapic_id, E7)
Change-Id: I20799f0c09cf0292661e1f3cb93373b2c68b7314
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55284
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
The SKU ID for Cherry is retrieved via CBI interface.
Signed-off-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Change-Id: Icefa016c2e5f68bd194f76d2252856835c65b8e8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55383
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
|
|
This change removes the GBB flag that disables SW sync
BUG:184229267
TEST:manually running chromeos-firmwareupdate
Signed-off-by: Boris Mittelberg <bmbm@google.com>
Change-Id: Ie8b759a0cdb0c3a0a6458f64c16216459f076e27
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55400
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
volet don't support usb4, remove it to prevent USBC(P0) issue.
BUG=b:189740531
TEST=build and verify USB(P0) disaply out normal
Signed-off-by: Sheng-Liang Pan <sheng-liang.pan@quanta.corp-partner.google.com>
Change-Id: Ia78c7cee76ec2e3a5334ad8805a0d45616aade93
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55344
Reviewed-by: YH Lin <yueherngl@google.com>
Reviewed-by: Zhuohao Lee <zhuohao@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add EC_HOST_EVENT_HANG_DETECT to S3/S5/S0ix wake mask. This event is
sent when the EC detects the AP didn't fully enter a sleep state.
BUG=b:186571086
TEST=Trigger hang detect while AP is in S0ix, AP wakes from S0ix
Change-Id: I09ccf609fc453c19b4fb1ddaa5a0c86d7a85aad1
Signed-off-by: Rob Barnes <robbarnes@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55365
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
The patch updates PMC Descriptor which is part of Descriptor Region if
system equipped with Alder lake A0 silicon. This change allows to use
unified Descriptor Region for Alder lake A0(CPU ID:0x906a0) and B0
(CPUD ID:0x906a1) silicons.
BUG=B:187431859
TEST=Verified PMC Descriptor getting modified for Alder lake B0 silicon if
not updated.
coreboot logs appear as below with this patch:
On First boot after flashing the image:
coreboot-coreboot-unknown.9999.4589c0f Wed Jun 9 18:23:43 UTC 2021 bootblock starting (log level: 8)...
CPU: Genuine Intel(R) 0000
CPU: ID 906a0, Alderlake Platform, ucode: 0000001a
..
FMAP: Found "FLASH" version 1.1 at 0x1804000.
FMAP: base = 0x0 size = 0x2000000 #areas = 32
FMAP: area SI_DESC found @ 0 (4096 bytes)
SF: Detected 00 0000 with sector size 0x1000, total 0x2000000
Erasing flash addr 0 + 4 KiB
Update of PMC Descriptor successful, trigger GLOBAL RESET
Next boot after GLOBAL RESET:
coreboot-coreboot-unknown.9999.4589c0f Wed Jun 9 18:23:43 UTC 2021 bootblock starting (log level: 8)...
..
FMAP: area SI_DESC found @ 0 (4096 bytes)
SF: Detected 00 0000 with sector size 0x1000, total 0x2000000
Update of PMC Descriptor is not required!
VBOOT: Loading verstage.
..
CBFS: Found 'fallback/verstage' @0x2264c0 size 0x16b08 in mcache @0xfef84d38
Signed-off-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Change-Id: I6d9a2ce0f0b3e386eefa1962ce706b58f31a8576
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55254
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Note that there are assumptions about LAPIC MMIO location
in both AMD and Intel sources in coreboot proper.
Change-Id: I2c668f5f9b93d170351c00d77d003c230900e0b4
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55194
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Currently variant_has_fpmcu() is called very early in bootblock, before
eSPI is initialized. When checking CBI for its presence, that causes
an error and nothing else can be read from CBI in bootblock.
Moving it slightly later in bootblock doesn't hurt anything from a
timing standpoint, and allows CBI to be read.
BUG=None
TEST=See CBI get read and the FPMCU field read correctly.
Signed-off-by: Martin Roth <martinroth@chromium.org>
Change-Id: I6de44119e92c8820b266f9f07287706c7d4eb505
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54740
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Most of the Kconfig files for Intel SOC devices define the MAX_CPUS
value within src/soc/intel/*/Kconfig.
Move the definition there for Tiger Lake and remove from the mainboard
Kconfig files.
Signed-off-by: Andy Pont <andy.pont@sdcsystems.com>
Change-Id: If145b9eb5d99821f4ce513118e4417d05f821ef5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55307
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
speaker L/R
Add Realtek audio codec ALC5682I and speaker L/R the same way as in waddledee
BUG=b:188446060
BRANCH=dedede
TEST=Boot to check ALC5682I and speaker L/R are functional
Change-Id: I8173ffbfb1a8f18978a5e35c69972d4a6d8cb04a
Signed-off-by: Alex1 Kao <alex1_kao@pegatron.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54529
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Kirk Wang <kirk_wang@pegatron.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Provide functions to allow for variants to override only a few pads from
the baseboard table.
BUG=b:189362981
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: I3ae6c11ca8614d523f3402f1c1abb7c82124e473
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55324
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
|
|
Add low_power_probe config to camera devices so that driver skips initial
probe during kernel boot and hence prevents privacy LED blink.
BUG=b:178060668
TEST=Build and boot to OS on Drawcia. Ensure no blink on privacy LED.
Signed-off-by: Varshit Pandya <varshit.b.pandya@intel.com>
Change-Id: I00dfe2ce0b57ff3eaa258204f49e79a280754dcf
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52190
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add function to force memory training and add VPD variable to operate
this function.
Tested=On OCP Delta Lake, memory training can be forced via VPD.
Signed-off-by: Tim Chu <Tim.Chu@quantatw.com>
Change-Id: I53a923b51b36f9f5db491ef142109f58f9a4611d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51972
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jonathan Zhang <jonzhang@fb.com>
|
|
Correct GPIO settings as below reason:
1. GPP_D19/GPP_D20/GPP_D21 not being used but set to NF.
2. GPP_B7 should configure as WWAN SAR detect ODL, but set to GPI
BUG=b:188956448
BRANCH=dedede
TEST=The LTE DPR pin can be pulled down normally when someone
get close to the P-sensor antenna.
Signed-off-by: Tao Xia <xiatao5@huaqin.corp-partner.google.com>
Change-Id: Idc214fcd9c4631368a71f4d59bb644df739982ab
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55175
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Update DPTF parameters from internal thermal team.
BUG=b:181189479
BRANCH=dedede
TEST=emerge-dedede coreboot
Signed-off-by: Tao Xia <xiatao5@huaqin.corp-partner.google.com>
Change-Id: I379c0ea79a7c27bdd81ed41a54135f7284fb6412
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54715
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
This patch adds a new variant called Pazquel that is identical to Lazor
for now.
BUG=b:187232137
TEST=make
Signed-off-by: Yunlong Jia <yunlong.jia@ecs.corp-partner.google.com>
Change-Id: Ib531ea5df19fe91e619f23baada73842554538ad
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55268
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
This will tell the kernel to ignore PCI ASPM when suspending the device
and instead place the device into D3. We don't actually have a pin to
control power to the NVMe so we leave it in D3Hot. I'm not sure if
`PCI_RST#` is working correctly on S0i3 suspend/resume. If it's not
acting as expected we can add the reset GPIO and have the OS do it.
BUG=b:184617186
TEST=Run suspend_stress_test on guybrush for 10 cycles
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I29539ac120a9f1b7c1bfeaca745cfc82acfa461a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54967
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Power limits (PL1 and PL2) depend on the specific SKU of the CPU.
By expanding the SoC chip config power_limits_config member to
an array indexed by ADL_*_POWER_LIMITS_*_CORE macros, the
appropriate power limits are applied. Using this the correct
set of power limits are being selected from the array based on
system agent PCI ID. Based on this, chipset.cb file contains
the set of power limits being used by varieties of ADL boards.
These power limit values are as per document 619501.
BUG=None
BRANCH=None
TEST=Built and verified the following console output on below boards
On adlrvp (482):
CPU PL1 = 28 Watts
CPU PL2 = 64 Watts
On adlrvp (682):
CPU PL1 = 45 Watts
CPU PL2 = 115 Watts
On brya (282):
CPU PL1 = 15 Watts
CPU PL2 = 55 Watts
Change-Id: Ic1676e2b4d611cdc85e770f131d5b6d5ecd180be
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54676
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Selma Bensaid <selma.bensaid@intel.com>
|
|
This changes adds the EC_HOST_EVENT_USB_MUX to be dark resume source.
BUG=None
TEST=Build coreboot image successfully.
Signed-off-by: John Zhao <john.zhao@intel.com>
Change-Id: I6f4dcbc60a6cb131f28de205bd9ef436f2b508eb
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55126
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
IO MWAIT redirection is not enabled, and C-states are reported using the
_CST ACPI object, which overrides the P_LVLx values.
Change-Id: I737bd58bcda3e7c5f6591e4c2309530ff035e2c8
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55218
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
|
|
IO MWAIT redirection is not enabled. The code is missing, but C-states
should instead be reported using the _CST ACPI object.
Change-Id: I21fd2fa6ee4aa1ed57694549d5cb48159f37af26
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55217
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
|
|
Configure GPIO D22/D23/E11.
Add P-sensor to device tree, these registers are draft version.
BUG=b:178092096
BRANCH=dedede
TEST=built firmware and dmesg shows STH9324 initial success.
Change-Id: I2c8feedd6efc1a471304322a17480c836e22349e
Signed-off-by: Tony Huang <tony-huang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55133
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Using an array reduces the amount of boilerplate code.
Change-Id: Ic6a48a01d3b96e69273dc28bdb6699ce7c0931b2
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55246
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Some of the I2C buses are required to operate at different voltage level
compared to other I2C buses eg. I2C bus to Google Security Chip (GSC)
should be at 1.8V level. By default, all the I2C buses are initialized
to operate at 3.3 V. Add support to configure I2C pad RX select through
devicetree and update the concerned devicetree.
BUG=b:188538373
TEST=Build and boot to OS in Guybrush. Ensure that the communication
with GSC is fine. Build Majolica mainboard.
Change-Id: I595a64736fdac0274abffb68c5e521302275b845
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55149
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Some of the GPIOs are either re-purposed for different use-cases or are
unused in upcoming board phase (board version 2). Update the GPIO
configuration accordingly. Here are the GPIOs that are updated:
GPIO Board Id 1 Board Id 2
=============================================
GPIO31 TP183 EN_SPKR
GPIO69 EN_SPKR SD_AUX_REST_L
GPIO70 SD_AUX_RESET_L Unused TP27
GPIO74 RAM_ID_CHAN_SEL Unused TP49
BUG=b:189327557, b:188542649, b:188542497
TEST=Build Guybrush mainboard. Verify Audio is audible and SD card is
detected fine in Board ID 1.
Change-Id: I31523b3e03d2b59577f33eae548747834cfc98aa
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55148
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
GSC is connected with AP via i2c bus so we need to enable i2c in
psp_verstage.
Signed-off-by: Kangheui Won <khwon@chromium.org>
Change-Id: I5f7b73be67a692ea7de31ae53bd111d0e4b6998c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55136
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Update DPTF parameters from internal thermal team.
BUG=b:180875580
BRANCH=dedede
TEST=emerge-dedede coreboot
Signed-off-by: Tao Xia <xiatao5@huaqin.corp-partner.google.com>
Change-Id: Id18a38cddbcacbafbe2c54d94dbda5e00de02b3b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55208
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: Evan Green <evgreen@chromium.org>
|
|
If unspecified, chipset code already uses 101, and 0x65 == 101.
Change-Id: I524ca492fa577003df23017756f74a455582132f
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55212
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
|
|
These PCH PCIe ports are used and should be enabled.
Resolves: https://ticket.coreboot.org/issues/311
Change-Id: I26ace6e043c7c66f8944f0986923014703423b8c
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55169
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Swift Geek (Sebastian Grzywna) <swiftgeek@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
|
|
Looks like the comments were derived from a preproduction board's
schematics. Production boards use a different port mapping.
Change-Id: I40c267ff048959b131c22c07695212e8bd90c3f4
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55171
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Swift Geek (Sebastian Grzywna) <swiftgeek@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
|
|
Use the device aliases provided by alderlake chipset.cb instead of
the raw pci device+function. Take advantage of the default states
in chipset.cb and only list the devices that are enabled for all
shadowmountain board variants.
TEST=Dump devicetree device enable list without and with this CL, no
difference observed.
Change-Id: I2b769d653ad8ad8ff069a0787d00ff33ead5c912
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55206
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Use the device aliases provided by alderlake chipset.cb instead of
the raw pci device+function. Take advantage of the default states
in chipset.cb and only list the devices that are enabled for all
different adlrvp boards.
TEST=Dump devicetree device enable list without and with this CL, no
difference observed.
Change-Id: Ib9e82d953416c076588974f3167d00ae96f01bb5
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55205
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I095394d9a79506346b8464c850d03cbd8ce2b812
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55221
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
On Chromebooks the RAM code is implemented by the resistor straps
that we can read and decode from ADC. For Cherry the RAM code can be
read from ADC channel 2 and 3.
Signed-off-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Change-Id: I4f28bc1c567cb886bd90d930219981a6206b9bb9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55156
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
This patch adds support for SPM. This adds 43ms to the boot time.
TEST=program counter of SPM is correct value after booting up.
Signed-off-by: Dawei Chien <dawei.chien@mediatek.com>
Signed-off-by: Edward-JW Yang <edward-jw.yang@mediatek.corp-partner.google.com>
Signed-off-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Change-Id: I5f17f6d51fc9ad2d23c71c3c5cd29fdc777dc071
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55154
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Reviewed-by: Rex-BC Chen <rex-bc.chen@mediatek.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This reverts commit 2e665eb8daa2963c52092e694a5316dc544a23f5.
Reason for revert: Was submitted too early and out-of-order.
Change-Id: I119b7a81b849bbe3424d73d5fdf9b55481444686
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54971
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
I2C4 is not used pn Brya hence make below changes:
1. Disable it in SerialIoI2cMode.
2. Remove I2C4 config in common_soc_config.
TEST=Make sure FSP is not programming I2C4.
Change-Id: I94c72b7fac9d8a001913b5faa2c0c8a3e8b701e9
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55170
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Add support for LabTop Mk III (kblr) and LabTop Mk IV (cml)
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Change-Id: Iffa6061b0e600880b0c93746f35b1731e4841e31
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55128
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Only I2C controller 3 is used on this mainboard. Disable all other
controllers.
Change-Id: Id06d98787a0574a5b3a8dc2e86858dfcc7154606
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55090
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
|
|
The I2C bus at which the external RTC is attached to is operated at
standard speed (100 kHz) at coreboot runtime. The OS can choose to run it
at fast speed since it uses its own driver and controller setup.
Report additional bus timings for fast mode so that OS can do it right.
Change-Id: I82e11e5dde8ad1047713f105c5a6d020eebf1ffd
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55089
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add Goodix GT7996F touchscreen into devicetree for cret.
BUG=b:180547935, b:188501391
BRANCH=dedede
TEST=Built cret firmware and verified touchscreen function.
Signed-off-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Change-Id: I2a6f7c1e9900492937202c0bc6595674f1e79e5b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54872
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
|
|
For all of the audio devices in overridetree.cb add the probe matches
that will determine if the device should be enabled or not based on the
selected audio daughter board type.
AUDIO=MAX98357_ALC5682I_I2S: enable max98357, dmic1 and alc5682i
AUDIO=MAX98373_ALC5682_SNDW: enable max98373, dmic2 and alc5682
BUG=b:188696010
TEST=test different audio devices based on fw_config value:
> AUDIO=UNKNOWN
ectool cbi set 6 0x00000000 4 2
> AUDIO=MAX98357_ALC5682I_I2S
ectool cbi set 6 0x00000100 4 2
> AUDIO=MAX98373_ALC5682_SNDW
ectool cbi set 6 0x00000200 4 2
Change-Id: I6f159442516830f9d304d78c83f070e4fcff4a37
Signed-off-by: Sugnan Prabhu S <sugnan.prabhu.s@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54716
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
In order to resolve the I2C address conflict with another peripheral in
the upcoming hardware build, left speaker amplifier I2C address is
reconfigured.
BUG=b:188539052
TEST=Build Guybrush mainboard. On Guybrush board ID 1, all the 3
speaker amplifiers are added to the ACPI table.
\_SB.I2C2.D028: Realtek SPK AMP L at I2C: 03:28
\_SB.I2C2.D029: Realtek SPK AMP R at I2C: 03:29
\_SB.I2C2.D02A: Realtek SPK AMP L1 at I2C: 03:2a
At the OS side, the concerned speaker amplifiers are probed and
enumerated.
localhost ~ # i2cdetect -y -r 2
0 1 2 3 4 5 6 7 8 9 a b c d e f
00: -- -- -- -- -- -- -- -- -- -- -- -- --
10: -- -- -- -- -- -- -- -- -- -- UU -- -- -- -- --
20: -- -- -- -- -- -- -- -- UU UU -- -- -- -- -- --
30: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
40: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
50: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
60: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
70: -- -- -- -- -- -- -- --
Change-Id: I69a7e7dd65a459c2e5629ada1dea1f1660dd9990
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55028
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Configure I2C rise/fall time in device tree to ensure I2C
CLK runs accurately at I2C_SPEED_FAST (<400 kHz).
Measured I2C frequency changes are just as below after tuning:
touchpad: 434kHz ---> 391kHz
touchpanel: 439kHz ---> 382kHz
audio codec RT5682: 445kHz ---> 385kHz
BUG=b:187555396
BRANCH=dedede
TEST=Build and check after tuning I2C clock is under 400 kHz
Signed-off-by: Tao Xia <xiatao5@huaqin.corp-partner.google.com>
Change-Id: I8438e37be49f8a74f53fd8460110dac1a3f06993
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54249
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
The entries in the ACPI tables for the fingerprint module's SPI
configuration were incorrect.
1) The GPIO is routed to IOAPIC (and SCI), therefore in ACPI, it must be
described by Interrupt(), not GpioInt()
2) The chip-select signal was selected as 1, not 0 `device spi 0/1 on`
BUG=b:181635081
TEST=verified in kernel logs:
localhost # ~ dmesg|egrep 'cros-ec-dev|cros-ec-spi'
[ 4.569412] cros-ec-dev cros-ec-dev.1.auto: CrOS Fingerprint MCU detected
[ 4.575303] cros-ec-spi spi-PRP0001:00: Chrome EC device registered
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: I9ef6c99f011969fc444e0c12b806529cb82bba3d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55147
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
As per the comments in CB:54090 mainboard api
mainboard_tcss_get_port_info() is simplified and moved to tcss common
block code.
Signed-off-by: Deepti Deshatty <deepti.deshatty@intel.com>
Change-Id: I7894363df4862f7cfe733d93e6160677fb8a9e31
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54733
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
|
|
Further add initial Silicon UPD storage settings:
- SATA
- SD card
- eMMC
Signed-off-by: Lean Sheng Tan <lean.sheng.tan@intel.com>
Change-Id: Id4145fcf156756a610b8a9a705d4ab99fe7b0bf8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55082
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
|
|
Further add initial Silicon UPD settings for:
- PCIe root ports
- USB
Signed-off-by: Lean Sheng Tan <lean.sheng.tan@intel.com>
Change-Id: I60afb78a7997b8465dd6318f3abee28f95a65100
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55034
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add Elan eKTH7D18 touchscreen into devicetree for cret.
BUG=b:180547935, b:187484857
BRANCH=dedede
TEST=Built cret firmware and verified touchscreen function.
Signed-off-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Change-Id: Iab87ddfc7b46420439efa3e7e55c88ad4c27155d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54868
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
|
|
Further add initial silicon UPD settings for:
- graphics & display
- chipset lockdown
- PAVP
- legacy timer
- PCH master gating control
- HECI
This CL also enables HECI 1 in devicetree.cb.
Signed-off-by: Lean Sheng Tan <lean.sheng.tan@intel.com>
Change-Id: I657f44f8506640c23049614b2db9d1837e6d44ed
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54960
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
|
|
Configure I2C rise/fall time in device tree to ensure I2C
CLK runs accurately (380<frequency<400 kHz).
Measured touchpad I2C frequency is 394 kHz
BUG=b:189740533
BRANCH=dedede
TEST=Build bios and make sure frequency meets specification.
Change-Id: Ibc0504a5be6fe9237b8b30783c659a761d10561a
Signed-off-by: Zanxi Chen <chenzanxi@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55109
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
There are two touch pads that Sasukette used have the same I2C address.
It will show "/dev/input/event4: SPPT2600:00 06CB:CE9D Touchpad" when
the Synaptics touch pad is connected after running evtest under VT2.
BUG=b:189520603
BRANCH=dedede
TEST=It will show "/dev/input/event4: SYNA0A00:00 06CB:CE9D Touchpad"
when the Synaptics touch pad is connected after running evtest under VT2.
Signed-off-by: Tao Xia <xiatao5@huaqin.corp-partner.google.com>
Change-Id: If0bd80baa27dfeb7bcb43f0ca4b02e1228e372a6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55035
Reviewed-by: zanxi chen <chenzanxi@huaqin.corp-partner.google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Create the primus variant of the brya0 reference board by copying
the template files to a new directory named for the variant.
(Auto-generated by create_coreboot_variant.sh version 4.5.0)
BUG=b:188272162
BRANCH=None
TEST=util/abuild/abuild -p none -t google/brya -x -a
make sure the build includes GOOGLE_PRIMUS
Signed-off-by: Scott Chao <scott_chao@wistron.corp-partner.google.com>
Change-Id: I26787f296793b281b7f1ee1a7d240006163c6015
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55132
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
1) Hynix H9HCNNNCPMMLXR-NEE
2) Micron MT53E1G32D2NP-046 WT:B
BUG=b:186616388, b:181736400
Change-Id: I56bfe8aa4f8d8aab2011fa8d17b3b2c8659658e3
Signed-off-by: Amanda Huang <amanda_hwang@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54951
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
In order to support no MIPI camera variant, move related configuration into variant folder.
BUG=b:188272162
BRANCH=none
TEST=build no MIPI camera variant without error
Signed-off-by: Scott Chao <scott_chao@wistron.corp-partner.google.com>
Change-Id: I4e64d078a8e39732ad29443c3b09ca008a7e902f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55134
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Based on schematic and gpio table of volet, update gpio and
devicetree settings for volet Proto.
BUG=b:186334008
TEST=FW_NAME=volet emerge-volteer coreboot chromeos-bootimage
Signed-off-by: Sheng-Liang Pan <sheng-liang.pan@quanta.corp-partner.google.com>
Change-Id: Ia0e9557e01ce1e7a49a3dddf6da3e4a29587a8b7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55113
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
volet use same memory configuration from Voxel, copy voxel setting to
volet.
BUG=b:186334008
TEST=FW_NAME=volet emerge-volteer coreboot chromeos-bootimage
Signed-off-by: Sheng-Liang Pan <sheng-liang.pan@quanta.corp-partner.google.com>
Change-Id: I7e65b18f2ddae3d1ce02d9006153269697188f61
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55096
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: YH Lin <yueherngl@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
BUG=none
TEST=Use command $ lspci -vv
LTR+ is listed on DevCtl2
Signed-off-by: Bernardo Perez Priego <bernardo.perez.priego@intel.com>
Change-Id: If65d08a46b9e7304fbe4b92b7f1e6d4e08c599e7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54492
Reviewed-by: Ryan A Albazzaz <ryan.a.albazzaz@intel.corp-partner.google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
1. Add 1 port and 1 endpoint
2. Add support for OVTI8856
WFC is on I2C0
BUG=None
BRANCH=None
TEST=Build and boot brya
Signed-off-by: Meera Ravindranath <meera.ravindranath@intel.com>
Signed-off-by: Varshit B Pandya <varshit.b.pandya@intel.com>
Change-Id: Ic5e9c28f255bdf86a68ce80a4f853be4e7c7ccfe
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52013
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Id2bdce5871f57e9edb17f89cba61b5c5ae018566
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55104
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ia6199c70163d32467abe5ba5da55c73ff62ba10f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55103
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
The chipset devicetree only has the essential PCIe devices enabled that
are needed for the SoC code to work. It also defines aliases for all
PCIe devices that can be used to reference the devices in the mainboard-
specific devicetrees and devicetree overrides. To make the change easier
to review that part will be done in a follow-up patch.
Despite missing in the PPR, device pci 18.7 exists on Picasso.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I6b7c3fd32579a23539594672593a243172c161c7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50626
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
Add Silicon upd settings for LPSS (GSPI/UART/I2C).
Signed-off-by: Lean Sheng Tan <lean.sheng.tan@intel.com>
Change-Id: Ib0c3cd1d37ff9892d09d6d86ac50e230549c7e53
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54959
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
Already released Linux versions did not have the needed ACPI-extension
in the RTC driver. If the ACPI-Support is enabled for the RTC, this
older Linux will not be able to use this device as it will be claimed by
the PNP-drivers. As there is no way to avoid that an older Linux kernel
meets a newer coreboot in the field, we need to disable the ACPI
support for the RTC for the mc_apl-based mainboards.
Change-Id: I9f9939ba3234dc3654a4ef8a498649453941ebdf
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55004
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
TEST=Boot to OS and verify acpi tables.
Signed-off-by: Bora Guvendik <bora.guvendik@intel.com>
Change-Id: I3c78ac44afa3515acef9ea2d59f22f95e6b45e90
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54490
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: John Zhao <john.zhao@intel.corp-partner.google.com>
Reviewed-by: John Zhao <john.zhao@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
