| Age | Commit message (Collapse) | Author |
|---|
|
speaker L/R
Add Realtek audio codec ALC5682I and speaker L/R the same way as in waddledee
BUG=b:188446060
BRANCH=dedede
TEST=Boot to check ALC5682I and speaker L/R are functional
Change-Id: I8173ffbfb1a8f18978a5e35c69972d4a6d8cb04a
Signed-off-by: Alex1 Kao <alex1_kao@pegatron.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54529
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Kirk Wang <kirk_wang@pegatron.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Provide functions to allow for variants to override only a few pads from
the baseboard table.
BUG=b:189362981
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: I3ae6c11ca8614d523f3402f1c1abb7c82124e473
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55324
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
|
|
Add low_power_probe config to camera devices so that driver skips initial
probe during kernel boot and hence prevents privacy LED blink.
BUG=b:178060668
TEST=Build and boot to OS on Drawcia. Ensure no blink on privacy LED.
Signed-off-by: Varshit Pandya <varshit.b.pandya@intel.com>
Change-Id: I00dfe2ce0b57ff3eaa258204f49e79a280754dcf
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52190
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add function to force memory training and add VPD variable to operate
this function.
Tested=On OCP Delta Lake, memory training can be forced via VPD.
Signed-off-by: Tim Chu <Tim.Chu@quantatw.com>
Change-Id: I53a923b51b36f9f5db491ef142109f58f9a4611d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51972
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jonathan Zhang <jonzhang@fb.com>
|
|
Correct GPIO settings as below reason:
1. GPP_D19/GPP_D20/GPP_D21 not being used but set to NF.
2. GPP_B7 should configure as WWAN SAR detect ODL, but set to GPI
BUG=b:188956448
BRANCH=dedede
TEST=The LTE DPR pin can be pulled down normally when someone
get close to the P-sensor antenna.
Signed-off-by: Tao Xia <xiatao5@huaqin.corp-partner.google.com>
Change-Id: Idc214fcd9c4631368a71f4d59bb644df739982ab
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55175
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Update DPTF parameters from internal thermal team.
BUG=b:181189479
BRANCH=dedede
TEST=emerge-dedede coreboot
Signed-off-by: Tao Xia <xiatao5@huaqin.corp-partner.google.com>
Change-Id: I379c0ea79a7c27bdd81ed41a54135f7284fb6412
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54715
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
This patch adds a new variant called Pazquel that is identical to Lazor
for now.
BUG=b:187232137
TEST=make
Signed-off-by: Yunlong Jia <yunlong.jia@ecs.corp-partner.google.com>
Change-Id: Ib531ea5df19fe91e619f23baada73842554538ad
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55268
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
This will tell the kernel to ignore PCI ASPM when suspending the device
and instead place the device into D3. We don't actually have a pin to
control power to the NVMe so we leave it in D3Hot. I'm not sure if
`PCI_RST#` is working correctly on S0i3 suspend/resume. If it's not
acting as expected we can add the reset GPIO and have the OS do it.
BUG=b:184617186
TEST=Run suspend_stress_test on guybrush for 10 cycles
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I29539ac120a9f1b7c1bfeaca745cfc82acfa461a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54967
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Power limits (PL1 and PL2) depend on the specific SKU of the CPU.
By expanding the SoC chip config power_limits_config member to
an array indexed by ADL_*_POWER_LIMITS_*_CORE macros, the
appropriate power limits are applied. Using this the correct
set of power limits are being selected from the array based on
system agent PCI ID. Based on this, chipset.cb file contains
the set of power limits being used by varieties of ADL boards.
These power limit values are as per document 619501.
BUG=None
BRANCH=None
TEST=Built and verified the following console output on below boards
On adlrvp (482):
CPU PL1 = 28 Watts
CPU PL2 = 64 Watts
On adlrvp (682):
CPU PL1 = 45 Watts
CPU PL2 = 115 Watts
On brya (282):
CPU PL1 = 15 Watts
CPU PL2 = 55 Watts
Change-Id: Ic1676e2b4d611cdc85e770f131d5b6d5ecd180be
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54676
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Selma Bensaid <selma.bensaid@intel.com>
|
|
This changes adds the EC_HOST_EVENT_USB_MUX to be dark resume source.
BUG=None
TEST=Build coreboot image successfully.
Signed-off-by: John Zhao <john.zhao@intel.com>
Change-Id: I6f4dcbc60a6cb131f28de205bd9ef436f2b508eb
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55126
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
IO MWAIT redirection is not enabled, and C-states are reported using the
_CST ACPI object, which overrides the P_LVLx values.
Change-Id: I737bd58bcda3e7c5f6591e4c2309530ff035e2c8
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55218
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
|
|
IO MWAIT redirection is not enabled. The code is missing, but C-states
should instead be reported using the _CST ACPI object.
Change-Id: I21fd2fa6ee4aa1ed57694549d5cb48159f37af26
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55217
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
|
|
Configure GPIO D22/D23/E11.
Add P-sensor to device tree, these registers are draft version.
BUG=b:178092096
BRANCH=dedede
TEST=built firmware and dmesg shows STH9324 initial success.
Change-Id: I2c8feedd6efc1a471304322a17480c836e22349e
Signed-off-by: Tony Huang <tony-huang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55133
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Using an array reduces the amount of boilerplate code.
Change-Id: Ic6a48a01d3b96e69273dc28bdb6699ce7c0931b2
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55246
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Some of the I2C buses are required to operate at different voltage level
compared to other I2C buses eg. I2C bus to Google Security Chip (GSC)
should be at 1.8V level. By default, all the I2C buses are initialized
to operate at 3.3 V. Add support to configure I2C pad RX select through
devicetree and update the concerned devicetree.
BUG=b:188538373
TEST=Build and boot to OS in Guybrush. Ensure that the communication
with GSC is fine. Build Majolica mainboard.
Change-Id: I595a64736fdac0274abffb68c5e521302275b845
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55149
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Some of the GPIOs are either re-purposed for different use-cases or are
unused in upcoming board phase (board version 2). Update the GPIO
configuration accordingly. Here are the GPIOs that are updated:
GPIO Board Id 1 Board Id 2
=============================================
GPIO31 TP183 EN_SPKR
GPIO69 EN_SPKR SD_AUX_REST_L
GPIO70 SD_AUX_RESET_L Unused TP27
GPIO74 RAM_ID_CHAN_SEL Unused TP49
BUG=b:189327557, b:188542649, b:188542497
TEST=Build Guybrush mainboard. Verify Audio is audible and SD card is
detected fine in Board ID 1.
Change-Id: I31523b3e03d2b59577f33eae548747834cfc98aa
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55148
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
GSC is connected with AP via i2c bus so we need to enable i2c in
psp_verstage.
Signed-off-by: Kangheui Won <khwon@chromium.org>
Change-Id: I5f7b73be67a692ea7de31ae53bd111d0e4b6998c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55136
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Update DPTF parameters from internal thermal team.
BUG=b:180875580
BRANCH=dedede
TEST=emerge-dedede coreboot
Signed-off-by: Tao Xia <xiatao5@huaqin.corp-partner.google.com>
Change-Id: Id18a38cddbcacbafbe2c54d94dbda5e00de02b3b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55208
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: Evan Green <evgreen@chromium.org>
|
|
If unspecified, chipset code already uses 101, and 0x65 == 101.
Change-Id: I524ca492fa577003df23017756f74a455582132f
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55212
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
|
|
These PCH PCIe ports are used and should be enabled.
Resolves: https://ticket.coreboot.org/issues/311
Change-Id: I26ace6e043c7c66f8944f0986923014703423b8c
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55169
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Swift Geek (Sebastian Grzywna) <swiftgeek@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
|
|
Looks like the comments were derived from a preproduction board's
schematics. Production boards use a different port mapping.
Change-Id: I40c267ff048959b131c22c07695212e8bd90c3f4
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55171
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Swift Geek (Sebastian Grzywna) <swiftgeek@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
|
|
Use the device aliases provided by alderlake chipset.cb instead of
the raw pci device+function. Take advantage of the default states
in chipset.cb and only list the devices that are enabled for all
shadowmountain board variants.
TEST=Dump devicetree device enable list without and with this CL, no
difference observed.
Change-Id: I2b769d653ad8ad8ff069a0787d00ff33ead5c912
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55206
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Use the device aliases provided by alderlake chipset.cb instead of
the raw pci device+function. Take advantage of the default states
in chipset.cb and only list the devices that are enabled for all
different adlrvp boards.
TEST=Dump devicetree device enable list without and with this CL, no
difference observed.
Change-Id: Ib9e82d953416c076588974f3167d00ae96f01bb5
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55205
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I095394d9a79506346b8464c850d03cbd8ce2b812
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55221
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
On Chromebooks the RAM code is implemented by the resistor straps
that we can read and decode from ADC. For Cherry the RAM code can be
read from ADC channel 2 and 3.
Signed-off-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Change-Id: I4f28bc1c567cb886bd90d930219981a6206b9bb9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55156
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
This patch adds support for SPM. This adds 43ms to the boot time.
TEST=program counter of SPM is correct value after booting up.
Signed-off-by: Dawei Chien <dawei.chien@mediatek.com>
Signed-off-by: Edward-JW Yang <edward-jw.yang@mediatek.corp-partner.google.com>
Signed-off-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Change-Id: I5f17f6d51fc9ad2d23c71c3c5cd29fdc777dc071
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55154
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Reviewed-by: Rex-BC Chen <rex-bc.chen@mediatek.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This reverts commit 2e665eb8daa2963c52092e694a5316dc544a23f5.
Reason for revert: Was submitted too early and out-of-order.
Change-Id: I119b7a81b849bbe3424d73d5fdf9b55481444686
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54971
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
I2C4 is not used pn Brya hence make below changes:
1. Disable it in SerialIoI2cMode.
2. Remove I2C4 config in common_soc_config.
TEST=Make sure FSP is not programming I2C4.
Change-Id: I94c72b7fac9d8a001913b5faa2c0c8a3e8b701e9
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55170
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Add support for LabTop Mk III (kblr) and LabTop Mk IV (cml)
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Change-Id: Iffa6061b0e600880b0c93746f35b1731e4841e31
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55128
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Only I2C controller 3 is used on this mainboard. Disable all other
controllers.
Change-Id: Id06d98787a0574a5b3a8dc2e86858dfcc7154606
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55090
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
|
|
The I2C bus at which the external RTC is attached to is operated at
standard speed (100 kHz) at coreboot runtime. The OS can choose to run it
at fast speed since it uses its own driver and controller setup.
Report additional bus timings for fast mode so that OS can do it right.
Change-Id: I82e11e5dde8ad1047713f105c5a6d020eebf1ffd
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55089
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add Goodix GT7996F touchscreen into devicetree for cret.
BUG=b:180547935, b:188501391
BRANCH=dedede
TEST=Built cret firmware and verified touchscreen function.
Signed-off-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Change-Id: I2a6f7c1e9900492937202c0bc6595674f1e79e5b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54872
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
|
|
For all of the audio devices in overridetree.cb add the probe matches
that will determine if the device should be enabled or not based on the
selected audio daughter board type.
AUDIO=MAX98357_ALC5682I_I2S: enable max98357, dmic1 and alc5682i
AUDIO=MAX98373_ALC5682_SNDW: enable max98373, dmic2 and alc5682
BUG=b:188696010
TEST=test different audio devices based on fw_config value:
> AUDIO=UNKNOWN
ectool cbi set 6 0x00000000 4 2
> AUDIO=MAX98357_ALC5682I_I2S
ectool cbi set 6 0x00000100 4 2
> AUDIO=MAX98373_ALC5682_SNDW
ectool cbi set 6 0x00000200 4 2
Change-Id: I6f159442516830f9d304d78c83f070e4fcff4a37
Signed-off-by: Sugnan Prabhu S <sugnan.prabhu.s@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54716
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
In order to resolve the I2C address conflict with another peripheral in
the upcoming hardware build, left speaker amplifier I2C address is
reconfigured.
BUG=b:188539052
TEST=Build Guybrush mainboard. On Guybrush board ID 1, all the 3
speaker amplifiers are added to the ACPI table.
\_SB.I2C2.D028: Realtek SPK AMP L at I2C: 03:28
\_SB.I2C2.D029: Realtek SPK AMP R at I2C: 03:29
\_SB.I2C2.D02A: Realtek SPK AMP L1 at I2C: 03:2a
At the OS side, the concerned speaker amplifiers are probed and
enumerated.
localhost ~ # i2cdetect -y -r 2
0 1 2 3 4 5 6 7 8 9 a b c d e f
00: -- -- -- -- -- -- -- -- -- -- -- -- --
10: -- -- -- -- -- -- -- -- -- -- UU -- -- -- -- --
20: -- -- -- -- -- -- -- -- UU UU -- -- -- -- -- --
30: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
40: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
50: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
60: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
70: -- -- -- -- -- -- -- --
Change-Id: I69a7e7dd65a459c2e5629ada1dea1f1660dd9990
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55028
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Configure I2C rise/fall time in device tree to ensure I2C
CLK runs accurately at I2C_SPEED_FAST (<400 kHz).
Measured I2C frequency changes are just as below after tuning:
touchpad: 434kHz ---> 391kHz
touchpanel: 439kHz ---> 382kHz
audio codec RT5682: 445kHz ---> 385kHz
BUG=b:187555396
BRANCH=dedede
TEST=Build and check after tuning I2C clock is under 400 kHz
Signed-off-by: Tao Xia <xiatao5@huaqin.corp-partner.google.com>
Change-Id: I8438e37be49f8a74f53fd8460110dac1a3f06993
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54249
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
The entries in the ACPI tables for the fingerprint module's SPI
configuration were incorrect.
1) The GPIO is routed to IOAPIC (and SCI), therefore in ACPI, it must be
described by Interrupt(), not GpioInt()
2) The chip-select signal was selected as 1, not 0 `device spi 0/1 on`
BUG=b:181635081
TEST=verified in kernel logs:
localhost # ~ dmesg|egrep 'cros-ec-dev|cros-ec-spi'
[ 4.569412] cros-ec-dev cros-ec-dev.1.auto: CrOS Fingerprint MCU detected
[ 4.575303] cros-ec-spi spi-PRP0001:00: Chrome EC device registered
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: I9ef6c99f011969fc444e0c12b806529cb82bba3d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55147
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
As per the comments in CB:54090 mainboard api
mainboard_tcss_get_port_info() is simplified and moved to tcss common
block code.
Signed-off-by: Deepti Deshatty <deepti.deshatty@intel.com>
Change-Id: I7894363df4862f7cfe733d93e6160677fb8a9e31
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54733
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
|
|
Further add initial Silicon UPD storage settings:
- SATA
- SD card
- eMMC
Signed-off-by: Lean Sheng Tan <lean.sheng.tan@intel.com>
Change-Id: Id4145fcf156756a610b8a9a705d4ab99fe7b0bf8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55082
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
|
|
Further add initial Silicon UPD settings for:
- PCIe root ports
- USB
Signed-off-by: Lean Sheng Tan <lean.sheng.tan@intel.com>
Change-Id: I60afb78a7997b8465dd6318f3abee28f95a65100
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55034
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add Elan eKTH7D18 touchscreen into devicetree for cret.
BUG=b:180547935, b:187484857
BRANCH=dedede
TEST=Built cret firmware and verified touchscreen function.
Signed-off-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Change-Id: Iab87ddfc7b46420439efa3e7e55c88ad4c27155d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54868
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
|
|
Further add initial silicon UPD settings for:
- graphics & display
- chipset lockdown
- PAVP
- legacy timer
- PCH master gating control
- HECI
This CL also enables HECI 1 in devicetree.cb.
Signed-off-by: Lean Sheng Tan <lean.sheng.tan@intel.com>
Change-Id: I657f44f8506640c23049614b2db9d1837e6d44ed
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54960
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
|
|
Configure I2C rise/fall time in device tree to ensure I2C
CLK runs accurately (380<frequency<400 kHz).
Measured touchpad I2C frequency is 394 kHz
BUG=b:189740533
BRANCH=dedede
TEST=Build bios and make sure frequency meets specification.
Change-Id: Ibc0504a5be6fe9237b8b30783c659a761d10561a
Signed-off-by: Zanxi Chen <chenzanxi@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55109
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
There are two touch pads that Sasukette used have the same I2C address.
It will show "/dev/input/event4: SPPT2600:00 06CB:CE9D Touchpad" when
the Synaptics touch pad is connected after running evtest under VT2.
BUG=b:189520603
BRANCH=dedede
TEST=It will show "/dev/input/event4: SYNA0A00:00 06CB:CE9D Touchpad"
when the Synaptics touch pad is connected after running evtest under VT2.
Signed-off-by: Tao Xia <xiatao5@huaqin.corp-partner.google.com>
Change-Id: If0bd80baa27dfeb7bcb43f0ca4b02e1228e372a6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55035
Reviewed-by: zanxi chen <chenzanxi@huaqin.corp-partner.google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Create the primus variant of the brya0 reference board by copying
the template files to a new directory named for the variant.
(Auto-generated by create_coreboot_variant.sh version 4.5.0)
BUG=b:188272162
BRANCH=None
TEST=util/abuild/abuild -p none -t google/brya -x -a
make sure the build includes GOOGLE_PRIMUS
Signed-off-by: Scott Chao <scott_chao@wistron.corp-partner.google.com>
Change-Id: I26787f296793b281b7f1ee1a7d240006163c6015
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55132
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
1) Hynix H9HCNNNCPMMLXR-NEE
2) Micron MT53E1G32D2NP-046 WT:B
BUG=b:186616388, b:181736400
Change-Id: I56bfe8aa4f8d8aab2011fa8d17b3b2c8659658e3
Signed-off-by: Amanda Huang <amanda_hwang@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54951
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
In order to support no MIPI camera variant, move related configuration into variant folder.
BUG=b:188272162
BRANCH=none
TEST=build no MIPI camera variant without error
Signed-off-by: Scott Chao <scott_chao@wistron.corp-partner.google.com>
Change-Id: I4e64d078a8e39732ad29443c3b09ca008a7e902f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55134
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Based on schematic and gpio table of volet, update gpio and
devicetree settings for volet Proto.
BUG=b:186334008
TEST=FW_NAME=volet emerge-volteer coreboot chromeos-bootimage
Signed-off-by: Sheng-Liang Pan <sheng-liang.pan@quanta.corp-partner.google.com>
Change-Id: Ia0e9557e01ce1e7a49a3dddf6da3e4a29587a8b7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55113
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
volet use same memory configuration from Voxel, copy voxel setting to
volet.
BUG=b:186334008
TEST=FW_NAME=volet emerge-volteer coreboot chromeos-bootimage
Signed-off-by: Sheng-Liang Pan <sheng-liang.pan@quanta.corp-partner.google.com>
Change-Id: I7e65b18f2ddae3d1ce02d9006153269697188f61
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55096
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: YH Lin <yueherngl@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
BUG=none
TEST=Use command $ lspci -vv
LTR+ is listed on DevCtl2
Signed-off-by: Bernardo Perez Priego <bernardo.perez.priego@intel.com>
Change-Id: If65d08a46b9e7304fbe4b92b7f1e6d4e08c599e7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54492
Reviewed-by: Ryan A Albazzaz <ryan.a.albazzaz@intel.corp-partner.google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
1. Add 1 port and 1 endpoint
2. Add support for OVTI8856
WFC is on I2C0
BUG=None
BRANCH=None
TEST=Build and boot brya
Signed-off-by: Meera Ravindranath <meera.ravindranath@intel.com>
Signed-off-by: Varshit B Pandya <varshit.b.pandya@intel.com>
Change-Id: Ic5e9c28f255bdf86a68ce80a4f853be4e7c7ccfe
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52013
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Id2bdce5871f57e9edb17f89cba61b5c5ae018566
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55104
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ia6199c70163d32467abe5ba5da55c73ff62ba10f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55103
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
The chipset devicetree only has the essential PCIe devices enabled that
are needed for the SoC code to work. It also defines aliases for all
PCIe devices that can be used to reference the devices in the mainboard-
specific devicetrees and devicetree overrides. To make the change easier
to review that part will be done in a follow-up patch.
Despite missing in the PPR, device pci 18.7 exists on Picasso.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I6b7c3fd32579a23539594672593a243172c161c7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50626
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
Add Silicon upd settings for LPSS (GSPI/UART/I2C).
Signed-off-by: Lean Sheng Tan <lean.sheng.tan@intel.com>
Change-Id: Ib0c3cd1d37ff9892d09d6d86ac50e230549c7e53
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54959
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
Already released Linux versions did not have the needed ACPI-extension
in the RTC driver. If the ACPI-Support is enabled for the RTC, this
older Linux will not be able to use this device as it will be claimed by
the PNP-drivers. As there is no way to avoid that an older Linux kernel
meets a newer coreboot in the field, we need to disable the ACPI
support for the RTC for the mc_apl-based mainboards.
Change-Id: I9f9939ba3234dc3654a4ef8a498649453941ebdf
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55004
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
TEST=Boot to OS and verify acpi tables.
Signed-off-by: Bora Guvendik <bora.guvendik@intel.com>
Change-Id: I3c78ac44afa3515acef9ea2d59f22f95e6b45e90
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54490
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: John Zhao <john.zhao@intel.corp-partner.google.com>
Reviewed-by: John Zhao <john.zhao@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Variant mc_apl1 is the only one that uses gpio.c from baseboard. For
this reason, gpio.c is moved from baseboard to mc_apl1.
Change-Id: Ie2ba8181dfe887df9abbbd648f2cbdc6ffc65530
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54945
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
|
|
With commit 405f229689 (soc/intel/*: drop UART pad configuration from
common code) the UART pad configuration was dropped from common SoC
code. Through a second commit 5ff17ed393 (mb/siemens/mc_apl1: do UART
pad configuration at board-level) the UART pad configuration was made
for mc_apl1 baseboard. This change is also needed for all other mc_apl
boards.
Change-Id: If78726d9b141e4e7580cca3267f49c1a5b95d7fa
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54911
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
|
|
Upload the FSP-M UPD configs. This CL also updated the chip.h and
devicetree.cb with the relevant variables and configs.
This CL also updated the GPIO related settings (PMC & SD card) in
devicetree.cb.
Signed-off-by: Lean Sheng Tan <lean.sheng.tan@intel.com>
Change-Id: If6321064b37535b390cf3dd7c41a719c598a0cd7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54892
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
|
|
`mainboard_silicon_init_params()` should *only* be used for configuring
FSP options which can not be configured anywhere else. Therefore, use
the init phase from the mainboard_ops driver for configuring the GPIOs.
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Change-Id: Ia01091938ac113cb5cf95f046609a1ebf3620806
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48143
Reviewed-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Update the first version DPTF parameters received from the thermal team.
BUG=b:188936764
TEST=emerge-volteer coreboot chromeos-bootimage
Cq-Depend: chrome-internal:3851737
Signed-off-by: FrankChu <frank_chu@pegatron.corp-partner.google.com>
Change-Id: Id14b1d0bdd48c65eafbdd2e80b4611c86781be00
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54858
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Update devicetree and gpio driving of storo that enable stylus
Updates the GPIO configuration for GPP_C12 to
PAD_CFG_GPI_GPIO_DRIVER and device tree entry for PENH device to
use WAKEUP_ROUTE_GPIO_IRQ.
BUG=b:188519508,b:188365033
BRANCH=dedede
TEST=build bios and the pen behavior can be detected.
Change-Id: I2ffc969569b3ca29ba76326140f958a9707199f7
Signed-off-by: Zanxi Chen <chenzanxi@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54762
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I7571ed92b3c3fa79581e2c7342960ca31451af1f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54935
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
Change-Id: I84b9ef080f1ac91ea6f7273457b882677abf70d3
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52885
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The `write_offset` parameter is always zero. Remove it.
Change-Id: Ib63cb25904ad6c1c7424a9c01d8bf1e84c08453b
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52884
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
These PCIe and DMA ports are not available for adlrvp_m.
BUG=none
TEST=Boot device
Signed-off-by: Bernardo Perez Priego <bernardo.perez.priego@intel.com>
Change-Id: Ic568c692fbb82fb3fc70c0cafc2328f8fa2cd74d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54885
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Enabling AC connect/disconnect wake events in brya to meet Chrome OS
wake requirements.
These changes are similar to Volteer and Shadowmountain.
BUG=none
BRANCH=None
TEST=manual tested DUT wakes for AC connect/disconnect in S0ix
Change-Id: I14b3efd429e3aa701af534f150baf35fcdeb9f35
Signed-off-by: madhusudanarao amara <madhusudanarao.amara@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54855
Reviewed-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-by: Sooraj Govindan <sooraj.govindan@intel.corp-partner.google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Initial upload of the GPIO configs for EHL CRB.
This CL also includes the UART GPIO configs in early GPIO table.
Signed-off-by: Lean Sheng Tan <lean.sheng.tan@intel.com>
Change-Id: Ied4cbb34149b0b837597c0fc17dc5956f3ca409e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54891
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
We would like to have an easy way to completely disable TPM support on a
board. For boards that don't pre-select a TPM protocol via the
MAINBOARD_HAS_TPMx options, this is already possible with the
USER_NO_TPM option. In order to make this available for all boards, this
patch just removes the whole USER_TPMx option group and directly makes
the TPM1 and TPM2 options visible to menuconfig. The MAINBOARD_HAS_TPMx
options can still be used to select defaults and to prevent selection of
a protocol that the TPM is known to not support, but the NO_TPM option
always remains available.
Also fix some mainboards that selected TPM2 directly, which they're not
supposed to do (that's what MAINBOARD_HAS_TPM2 is for), and add a
missing dependency to TPM_CR50 so it is set correctly for a NO_TPM
scenario.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: Ib0a73da3c42fa4e8deffecb53f29ee38cbb51a93
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54641
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Christian Walter <christian.walter@9elements.com>
|
|
This fixes the following error from the Linux kernel:
ccp 0000:03:00.2: ioremap failed
ccp 0000:03:00.2: initialization failed
ccp: probe of 0000:03:00.2 failed with error -12
BUG=b:186575712,b:189202985
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Id1c6a6cbbdda2cb22e81e2b52b364617d6765e09
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54963
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This fixes the following error from the Linux kernel:
ccp 0000:03:00.2: ioremap failed
ccp 0000:03:00.2: initialization failed
ccp: probe of 0000:03:00.2 failed with error -12
BUG=b:186575712,b:189202985
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I5cbc620001d3c21c538b62ab2811b6e07269feb2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54962
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The firmware config field in CBI lets us control initialization
parameters based on the OEM design.
BUG=b:188713024
TEST=Build
Signed-off-by: Martin Roth <martinroth@chromium.org>
Change-Id: I56ddc7218688919f20f41e0f143419c39d83849d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54732
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
Since the default for the corresponding UPD of the Picasso FSP is
DXIO_PSPP_POWERSAVE and the devicetree default is DXIO_PSPP_PERFORMANCE,
add a deviectree setting for each board that's using the Picasso SoC
code to not change the setting for the existing boards.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I0008ebb0c0f339ed3bdf24ab95a20aa83d5be2c9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54934
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
Not sure which policy we should select here or if that should be done in
the board-specific devicetree overrides instead of the baseboard.
BUG=b:188793754
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I792d909ce75cb73571c9fec58c18f749ea3ae029
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54933
Reviewed-by: Matt Papageorge <matthewpapa07@gmail.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
BUG=b:188793754
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I5fd0021170777c755ecb78d339aec05ff786710f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54932
Reviewed-by: Matt Papageorge <matthewpapa07@gmail.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
BUG=b:188793754
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I262c4c3ae90d8d12fdfe71a3620739070a444a55
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54931
Reviewed-by: Matt Papageorge <matthewpapa07@gmail.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
All relevant USB phy settings can now be controlled via devicetree.
The given values are the AMD default ones.
For proper tuning procedure and values contact AMD.
Signed-off-by: Julian Schroeder <julianmarcusschroeder@gmail.com>
Change-Id: Ie8d08bde54f8c0cb8202ba111b9c7a9bd33fa03e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54785
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
Configure GPIO CAM_PDN5 (AP_XHCI_INIT_DONE) as output, so that
payloads (for example depthcharge) can assert it to notify EC to enable
USB VBUS.
BUG=b:187149602
TEST=emerge-asurada coreboot
BRANCH=asurada
Change-Id: I3bf63f91b8057e35be2780024a8b398c3044729b
Signed-off-by: Yu-Ping Wu <yupingso@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54902
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Build of the entire smm-class is skipped if we have
HAVE_SMI_HANDLER=n.
Change-Id: I64bdcb28a996609111861ebafe172493b0650354
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54852
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Rocky Phagura
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
ACPI code for this mainboard uses none of these values.
Change-Id: I429bf8dc229fd830ae662034a8b733c9ee669140
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54851
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
haboki/habokay is the same design as drawlat/drawcia, and differs only
in replacing Cr50 with discrete TPM.
BUG=b:187094464
TEST=FW_NAME=haboki emerge-keeby coreboot
Cq-Depend: chrome-internal:3850094
Change-Id: Id866927b7041c5bf1c73fb4f0c03798eb61efa79
Signed-off-by: Wisley Chen <wisley.chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54755
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add GPIO "beep enable" for switching on and off.
Signed-off-by: Trevor Wu <trevor.wu@mediatek.com>
Change-Id: Iddb781e30fa90f05767cceeb83e623432540dcc0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54739
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
Add new memory MT53E512M32D1NP-046 WT:B in the mem_parts_used.txt and
generate the SPD ID for the parts.
BUG=b:183057749
BRANCH=dedede
TEST=Build the cret board.
Signed-off-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Change-Id: Ib797af858e8f7ea275291e552102db74f4724aad
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54747
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add Goodix touchscreen according to the Programming Guide Rev.0.7
BUG=b:188872893
TEST=build and boot into OS.
check dmesg trying to add GDIX0000:00 device.
Signed-off-by: Ivy Jian <ivy_jian@compal.corp-partner.google.com>
Change-Id: I38c9bbf6e1c1531bf3524552db58c0bf183acbb4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54760
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
BUG=b:189053502
BRANCH=puff
TEST=build image and verified by thermal team.
Change-Id: Ic2337b9eabef158633c5e6dfa935ed5c8d3d76d1
Signed-off-by: Tony Huang <tony-huang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54718
Reviewed-by: Sam McNally <sammc@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This reverts commit 2f8a7046bb120d96022ada1e74545f859f97521f.
Reason for revert: CB:54752 makes this unnecessary
Change-Id: I3ad0bcafe50e3eafb9a106720c6c9ea5cb0efc4f
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54789
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add ELAN touchpad into devicetree for sasukette.
BUG=b:188376649
BRANCH=dedede
TEST=built sasukette firmware and verified touchpad function
Signed-off-by: lizhi7 <lizhi7@huaqin.corp-partner.google.com>
Change-Id: I898aeda936eb10ef4ead679a1c087060fad71a08
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54369
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Weimin Wu <wuweimin@huaqin.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Drawper would use synaptics touchpad.
BUG=b:184878424
TEST=emerge-dedede coreboot and check touchpad function work.
Change-Id: I2d2c205e19d8e3472e0fa7ca20fd38e381ac0de0
Signed-off-by: Tony Huang <tony-huang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54756
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Update ACPI HID to 10025682 for Machine driver probe
BUG=b:187912480
TEST=Build and boot to OS in Mancomb. Ensure that the sound card probed.
Signed-off-by: Ivy Jian <ivy_jian@compal.corp-partner.google.com>
Change-Id: I5dc87c7a8fb876adc26165655f8f2d4157aa68c9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54749
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Send USB_MUX host event for the connect/disconnect type C devices.
BUG=none
BRANCH=None
TEST=manual tested USB connect/disconnect
Change-Id: I5a720e1f1ea42f200e0e4c98f42894e4b92c67f8
Signed-off-by: madhusudanarao amara <madhusudanarao.amara@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54725
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-by: Sooraj Govindan <sooraj.govindan@intel.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
BUG=b:188446049
TEST=Build and boot to OS in mancomb. Ensure that the system can suspend
and resume successfully. Ensure that the sleep state GPIOs are
reflecting the state as expected.
Change-Id: I43e86a07075fe66f89c2c5665adc209e985e4f04
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54687
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Drawper support LTE+HDMI,
so use DB_PORTS_1A_HDMI_LTE to select HDMI VBT output for it.
BUG=b:186393848
BRANCH=dedede
TEST=Build and boot to OS check HDMI output works.
Change-Id: Ibf34cce1e3cbfce8a71dce880c50f85db9295b1e
Signed-off-by: Tony Huang <tony-huang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54645
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
DB_PORTS_1C_1A_LTE 6
DB_PORTS_1C 7
DB_PORTS_1A_HDMI_LTE 8
BUG=b:186393848
BRANCH=dedede
TEST=build pass
Change-Id: I8632960d7e538402bf033d07402116dac848f5ac
Signed-off-by: Tony Huang <tony-huang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54644
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Enable ASPM, Common Clock and Clock Power Managment. Accomplish this
by adding the options in the platform Kconfig as well as dxio
descriptors.
BUG=b:187743927
TEST=Boot to ChromeOS and see ASPM, CC and Clock PM enabled with lspci
Change-Id: I9d6e606763798afc6b797d7d24ee7cae09f9e33f
Signed-off-by: Matt Papageorge <matthewpapa07@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54681
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Enable ASPM, Common Clock and Clock Power Managment. Accomplish this
by adding the options in the platform Kconfig as well as dxio
descriptors.
BUG=b:187743927
TEST=Boot to ChromeOS and see ASPM, CC and Clock PM enabled with lspci
Change-Id: Iefc4b5b489cb8caf59f21dd4333d7af66ba47c32
Signed-off-by: Matt Papageorge <matthewpapa07@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54282
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
UI monitors this input event and sends global mic mute command to CRAS
when the physical switch is toggled.
BUG=b:184593945
BRANCH=puff
TEST=build image and verify with evtest on DUT.
Apply crrev.com/c/2870806 with chrome cmdline flag and verify global
mute is triggered.
Verify sequences of switch toggle and suspend/resume.
Change-Id: Id89947885fdd96c5b5d598bda6db127daf298dc3
Signed-off-by: Ben Zhang <benzh@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54333
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
MAINBOARD_HAS_TPM1 should not be selected, since the module is
replaceable.
Signed-off-by: Bill XIE <persmule@hardenedlinux.org>
Change-Id: Ia3790154476b0db54f37e1f3abb91ba5ee891c31
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54629
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Tested with BUILD_TIMELESS=1, coreboot.rom for the Asus P8Z77-M PRO
remains identical when not adding the .config file in it.
Change-Id: I7f1d93e500153a9821e7ddb693d77c864c879f0d
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54414
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Tested with BUILD_TIMELESS=1, coreboot.rom for the Asus P8Z77-V LX2
remains identical when not adding the .config file in it.
Change-Id: Ia84b07f5fec3c2969134b0d0bc39248d50ac04ff
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54413
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
The mainboard.c guard was only added to preserve reproducibility when
unifying the boards. The `install_intel_vga_int15_handler` function does
nothing when `VGA_ROM_RUN` is not selected. Remove the guard and always
select `INTEL_INT15` for simplicity.
Change-Id: If38ca49dba81921a3e7abe22542ae74d8914a38d
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54412
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
