summaryrefslogtreecommitdiff
path: root/src/mainboard
AgeCommit message (Collapse)Author
2020-05-11mainboard/asus/p3b-f: Reintroduce as variant of p2bKeith Hui
Fold this last ASUS 440BX board into the P2B family, while bringing in some changes: - Devicetree becomes overridetree. - Remove non-existent IR device and disable ACPI device on Super I/O to match OEM firmware. - Add SB GPO settings from OEM firmware to devicetree. This disables the SPD enabling magic this board needs. By moving the enabling part to bootblock the hacky enable_spd hook can be eliminated. - Initialize the serial port in bootblock, like the other boards. Boot tested on hardware. Change-Id: I65f2cb9d1bd4c82550de43889e3502526a46bd18 Signed-off-by: Keith Hui <buurin@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/41047 Reviewed-by: Angel Pons <th3fanbus@gmail.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-05-11mb/google/cyan/*: fixup GPIOsMatt DeVillier
Commit 73b723d [google/cyan: Switch Touchpad and Touchscreen...] in additon to changing the touchpad/touchscreen interrupts from edge to level triggered, also marked them as maskable. This was partially reverted in a86bbea0 [google/cyan: set touchscreen GPIO to non_maskable], but did not resolve all of the issues. Additionally, 73b723d also accidentally changed the pad interrupt select from L3 to L1 for all touchscreen GPIOs. Clean up this mess by setting all touchpad/touchscreen GPIOs back to maskable, and set the pad level to L3 for all touchscreen GPIOs. Tested on several cyan variants Change-Id: I70e8e2d4ff317c3b9b4108ed6c5bc80e9b0bbc75 Signed-off-by: Matt DeVillier <matt.devillier@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/41176 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Angel Pons <th3fanbus@gmail.com>
2020-05-11mb/google/octopus/variants/dood: Disable XHCI LFPS power managementKenneth Chan
LTE module Fibocom L850-GL is lost after idle overnight, with this workaround, host will not initiate U3 wakeup at the same time with device, which will avoid the race condition. Disable XHCI LFPS power management. If the option is set in the devicetree, the bits[7:4] in XHCI MMIO BAR + offset 0x80A4 (PMCTRL_REG) will be updated from default 9 to 0. BUG=b:155955302 BRANCH=octopus TEST=build coreboot with DisableXhciLfpsPM being set to 1 and flash the image to the device. Run following command to check if bits[7:4] are set 0: >iotools mmio_read32 "XHCI MMIO BAR + 0x80A4" Signed-off-by: Kenneth Chan <kenneth.chan@quanta.corp-partner.google.com> Change-Id: I88357f44317a5cff2e04508638eb065e5ada4c4c Reviewed-on: https://review.coreboot.org/c/coreboot/+/41143 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Marco Chen <marcochen@google.com> Reviewed-by: Ren Kuo <ren.kuo@quanta.corp-partner.google.com>
2020-05-11mb/intel/jasperlake_rvp: Turn off unused I2C lanesPandya, Varshit B
Change-Id: Id49032c0f9b701fe12873c80e1bc0e4b64ba7106 Signed-off-by: Pandya, Varshit B <varshit.b.pandya@intel.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/40859 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com> Reviewed-by: Ronak Kanabar <ronak.kanabar@intel.com> Reviewed-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
2020-05-11mb/intel/jasperlake_rvp: Add support for SMI handlerMaulik V Vaghela
SMI handler was not present in jasperlake rvp to handle wake events when platform goes to sleep or shutdown or s0ix. Adding this support for board which supports chromeec. BUG=None BRANCH=None TEST=Check wake event on board and platform wakes up due to events lid wake event or power button press. Change-Id: I8e35955b06d6efaf9275ec03f519c9bcaa9ba345 Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/40853 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Ronak Kanabar <ronak.kanabar@intel.com>
2020-05-11mb/google/kukui: fix screen scrolling on devices using anx7625Paul Ma
anx7625 enables MIPI receiver to check EOTP packet as default. If MIPI_DSI_MODE_EOT_PACKET is not set in flags, soc dsi will not send out EOTP packet and some panel models will display abnormal such as scrolling all the time. BUG=b:144824303 BRANCH=kukui TEST=boot damu board, edp panel with anx7625 as bridge boots up without scrolling. Signed-off-by: Paul Ma <magf@bitland.corp-partner.google.com> Change-Id: Iad651202bde2a40024af8c12153143ada2ce2439 Reviewed-on: https://review.coreboot.org/c/coreboot/+/41161 Reviewed-by: Yu-Ping Wu <yupingso@google.com> Reviewed-by: Hung-Te Lin <hungte@chromium.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-05-11mb/google/kukui: Fix backlight flash white before show logoJitao Shi
Turn backlight off before panel poweron. BUG=b:155107047 TEST=make # board = kukui BRANCH=kukui Signed-off-by: Jitao Shi <jitao.shi@mediatek.com> Change-Id: I0f31923bd7c1dfa26d4b1bbd0a230ae400b08ca3 Reviewed-on: https://review.coreboot.org/c/coreboot/+/41146 Reviewed-by: Hung-Te Lin <hungte@chromium.org> Reviewed-by: Yu-Ping Wu <yupingso@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-05-11mb/google/octopus: Fix default FMDMatt DeVillier
On Apollo Lake/Gemini Lake platforms, FSP requires more than a simple RW_MRC_CACHE; without the RECOVERY and VAR cache regions, FSP-m will fail on s3 resume and trigger a full reset instead. This fixes the default.fmd for octopus to match that used for reef. Test: build/boot google/ampton, verify sleep/resume works under Linux with 5.x kernel. Change-Id: I8565aa93256df7d6e0b359d70e9305f34e5ccb60 Signed-off-by: Matt DeVillier <matt.devillier@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/41016 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Angel Pons <th3fanbus@gmail.com>
2020-05-10mb/google/kahlee: Hold WLAN PCIe reset low at boot for mordinKevin Chiu
gpio70 is assigned to use as WLAN rst in new schematic to fulfill RTK RTL8822CE power sequence: WLAN rst will need to be active at least 50ms after WLAN power on. Also in order to keep the rst low in consistency, override default gpio70 to low. BUG=b:154357210,b:154848243 BRANCH=master TEST=emerge-grunt coreboot Change-Id: I98c8afe42b7f92016f83483acbb3b9ae64b159f7 Signed-off-by: Kevin Chiu <Kevin.Chiu@quantatw.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/40805 Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Martin Roth <martinroth@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-05-10mb/google/kahlee: Don't reset the touchpad/screen on bootMartin Roth
touchpad & touchscreen power enable gets reset during resume causing unintended wake interrupts, causing dark resume failures. This prevents the board from being shut down after it's been suspended for a long period of time and can end up draining the battery. BUG=b:153173717 TEST=Build only - Needs to be tested by ODMs. Signed-off-by: Martin Roth <martin@coreboot.org> Change-Id: If403da8853e59eaaf589062c9bd6f10deb626998 Reviewed-on: https://review.coreboot.org/c/coreboot/+/41063 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Kevin Chiu <Kevin.Chiu@quantatw.com>
2020-05-10src/mainboard: Replace GPLv2 long form headers with SPDX headerElyes HAOUAS
Change-Id: I64d9468682a4aae3084b17b8724d035f17d01dff Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr> Reviewed-on: https://review.coreboot.org/c/coreboot/+/41187 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Patrick Georgi <pgeorgi@google.com>
2020-05-09src/: Replace GPL boilerplate with SPDX headerPatrick Georgi
Command used: perl -i -p0e 's|(\#\#*)[\w*]*.*is[\#\s]*licensed[\#\s]*under[\#\s]*the[\#\s]*terms[\#\s]*of[\#\s]*the[\#\s]*GNU[\#\s]*General[\#\s]*Public[\#\s]*License[\#\s]*version[\#\s]*2,[\#\s]*as[\#\s]*published[\#\s]*by[\#\s]*the[\#\s]*Free[\#\s]*Software[\#\s]*Foundation,[\#\s]*and[\#\s]*may[\#\s]*be[\#\s]*copied,[\#\s]*distributed,[\#\s]*and[\#\s]*modified[\#\s]*under[\#\s]*those[\#\s]*terms.[\#\s]*This[\#\s]*program[\#\s]*is[\#\s]*distributed[\#\s]*in[\#\s]*the[\#\s]*hope[\#\s]*that[\#\s]*it[\#\s]*will[\#\s]*be[\#\s]*useful,[\#\s]*but[\#\s]*WITHOUT[\#\s]*ANY[\#\s]*WARRANTY;[\#\s]*without[\#\s]*even[\#\s]*the[\#\s]*implied[\#\s]*warranty[\#\s]*of[\#\s]*MERCHANTABILITY[\#\s]*or[\#\s]*FITNESS[\#\s]*FOR[\#\s]*A[\#\s]*PARTICULAR[\#\s]*PURPOSE.[\#\s]*See[\#\s]*the[\#\s]*GNU[\#\s]*General[\#\s]*Public[\#\s]*License[\#\s]*for[\#\s]*more[\#\s]*details.\s(#* *\n)*|\1 SPDX-License-Identifier: GPL-2.0-only\n\n|' $(cat filelist) Change-Id: Ia7ce0a78f96563b8dc0f6eb648c4ba4cefb2b838 Signed-off-by: Patrick Georgi <pgeorgi@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/41180 Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-05-09src/: Replace GPL boilerplate with SPDX headersPatrick Georgi
Used commands: perl -i -p0e 's|\/\*[\s*]*.*is free software[:;][\s*]*you[\s*]*can[\s*]*redistribute[\s*]*it[\s*]*and\/or[\s*]*modify[\s*]*it[\s*]*under[\s*]*the[\s*]*terms[\s*]*of[\s*]*the[\s*]*GNU[\s*]*General[\s*]*Public[\s*]*License[\s*]*as[\s*]*published[\s*]*by[\s*]*the[\s*]*Free[\s*]*Software[\s*]*Foundation[;,][\s*]*version[\s*]*2[\s*]*of[\s*]*the[\s*]*License.[\s*]*This[\s*]*program[\s*]*is[\s*]*distributed[\s*]*in[\s*]*the[\s*]*hope[\s*]*that[\s*]*it[\s*]*will[\s*]*be[\s*]*useful,[\s*]*but[\s*]*WITHOUT[\s*]*ANY[\s*]*WARRANTY;[\s*]*without[\s*]*even[\s*]*the[\s*]*implied[\s*]*warranty[\s*]*of[\s*]*MERCHANTABILITY[\s*]*or[\s*]*FITNESS[\s*]*FOR[\s*]*A[\s*]*PARTICULAR[\s*]*PURPOSE.[\s*]*See[\s*]*the[\s*]*GNU[\s*]*General[\s*]*Public[\s*]*License[\s*]*for[\s*]*more[\s*]*details.[\s*]*\*\/|/* SPDX-License-Identifier: GPL-2.0-only */|' $(cat filelist) perl -i -p0e 's|\/\*[\s*]*.*is[\s*]*free[\s*]*software[:;][\s*]*you[\s*]*can[\s*]*redistribute[\s*]*it[\s*]*and/or[\s*]*modify[\s*]*it[\s*]*under[\s*]*the[\s*]*terms[\s*]*of[\s*]*the[\s*]*GNU[\s*]*General[\s*]*Public[\s*]*License[\s*]*as[\s*]*published[\s*]*by[\s*]*the[\s*]*Free[\s*]*Software[\s*]*Foundation[;,][\s*]*either[\s*]*version[\s*]*2[\s*]*of[\s*]*the[\s*]*License,[\s*]*or[\s*]*.at[\s*]*your[\s*]*option.[\s*]*any[\s*]*later[\s*]*version.[\s*]*This[\s*]*program[\s*]*is[\s*]*distributed[\s*]*in[\s*]*the[\s*]*hope[\s*]*that[\s*]*it[\s*]*will[\s*]*be[\s*]*useful,[\s*]*but[\s*]*WITHOUT[\s*]*ANY[\s*]*WARRANTY;[\s*]*without[\s*]*even[\s*]*the[\s*]*implied[\s*]*warranty[\s*]*of[\s*]*MERCHANTABILITY[\s*]*or[\s*]*FITNESS[\s*]*FOR[\s*]*A[\s*]*PARTICULAR[\s*]*PURPOSE.[\s*]*See[\s*]*the[\s*]*GNU[\s*]*General[\s*]*Public[\s*]*License[\s*]*for[\s*]*more[\s*]*details.[\s*]*\*\/|/* SPDX-License-Identifier: GPL-2.0-or-later */|' $(cat filelist) perl -i -p0e 's|\/\*[\s*]*.*is[\s*#]*free[\s*#]*software[;:,][\s*#]*you[\s*#]*can[\s*#]*redistribute[\s*#]*it[\s*#]*and/or[\s*#]*modify[\s*#]*it[\s*#]*under[\s*#]*the[\s*#]*terms[\s*#]*of[\s*#]*the[\s*#]*GNU[\s*#]*General[\s*#]*Public[\s*#]*License[\s*#]*as[\s*#]*published[\s*#]*by[\s*#]*the[\s*#]*Free[\s*#]*Software[\s*#]*Foundation[;:,][\s*#]*either[\s*#]*version[\s*#]*3[\s*#]*of[\s*#]*the[\s*#]*License[;:,][\s*#]*or[\s*#]*.at[\s*#]*your[\s*#]*option.[\s*#]*any[\s*#]*later[\s*#]*version.[\s*#]*This[\s*#]*program[\s*#]*is[\s*#]*distributed[\s*#]*in[\s*#]*the[\s*#]*hope[\s*#]*that[\s*#]*it[\s*#]*will[\s*#]*be[\s*#]*useful[;:,][\s*#]*but[\s*#]*WITHOUT[\s*#]*ANY[\s*#]*WARRANTY[;:,][\s*#]*without[\s*#]*even[\s*#]*the[\s*#]*implied[\s*#]*warranty[\s*#]*of[\s*#]*MERCHANTABILITY[\s*#]*or[\s*#]*FITNESS[\s*#]*FOR[\s*#]*A[\s*#]*PARTICULAR[\s*#]*PURPOSE.[\s*#]*See[\s*#]*the[\s*#]*GNU[\s*#]*General[\s*#]*Public[\s*#]*License[\s*#]*for[\s*#]*more[\s*#]*details.[\s*]*\*\/|/* SPDX-License-Identifier: GPL-3.0-or-later */|' $(cat filelist) perl -i -p0e 's|(\#\#*)[\w]*.*is free software[:;][\#\s]*you[\#\s]*can[\#\s]*redistribute[\#\s]*it[\#\s]*and\/or[\#\s]*modify[\#\s]*it[\s\#]*under[\s \#]*the[\s\#]*terms[\s\#]*of[\s\#]*the[\s\#]*GNU[\s\#]*General[\s\#]*Public[\s\#]*License[\s\#]*as[\s\#]*published[\s\#]*by[\s\#]*the[\s\#]*Free[\s\#]*Software[\s\#]*Foundation[;,][\s\#]*version[\s\#]*2[\s\#]*of[\s\#]*the[\s\#]*License.*[\s\#]*This[\s\#]*program[\s\#]*is[\s\#]*distributed[\s\#]*in[\s\#]*the[\s\#]*hope[\s\#]*that[\s\#]*it[\s\#]*will[\#\s]*be[\#\s]*useful,[\#\s]*but[\#\s]*WITHOUT[\#\s]*ANY[\#\s]*WARRANTY;[\#\s]*without[\#\s]*even[\#\s]*the[\#\s]*implied[\#\s]*warranty[\#\s]*of[\#\s]*MERCHANTABILITY[\#\s]*or[\#\s]*FITNESS[\#\s]*FOR[\#\s]*A[\#\s]*PARTICULAR[\#\s]*PURPOSE.[\#\s]*See[\#\s]*the[\#\s]*GNU[\#\s]*General[\#\s]*Public[\#\s]*License[\#\s]*for[\#\s]*more[\#\s]*details.\s(#* *\n)*|\1 SPDX-License-Identifier: GPL-2.0-only\n\n|' $(cat filelist) perl -i -p0e 's|(\#\#*)[\w*]*.*is free software[:;][\s*]*you[\s*]*can[\s*]*redistribute[\s*]*it[\s*]*and\/or[\s*]*modify[\s*]*it[\s*]*under[\s*]*the[\s*]*terms[\s*]*of[\s*]*the[\s*]*GNU[\s*]*General[\s*]*Public[\s*]*License[\s*]*as[\s*]*published[\s*]*by[\s*]*the[\s*]*Free[\s*]*Software[\s*]*Foundation[;,][\s*]*version[\s*]*2[\s*]*of[\s*]*the[\s*]*License.[\s*]*This[\s*]*program[\s*]*is[\s*]*distributed[\s*]*in[\s*]*the[\s*]*hope[\s*]*that[\s*]*it[\s*]*will[\s*]*be[\s*]*useful,[\s*]*but[\s*]*WITHOUT[\s*]*ANY[\s*]*WARRANTY;[\s*]*without[\s*]*even[\s*]*the[\s*]*implied[\s*]*warranty[\s*]*of[\s*]*MERCHANTABILITY[\s*]*or[\s*]*FITNESS[\s*]*FOR[\s*]*A[\s*]*PARTICULAR[\s*]*PURPOSE.[\s*]*See[\s*]*the[\s*]*GNU[\s*]*General[\s*]*Public[\s*]*License[\s*]*for[\s*]*more[\s*]*details.\s(#* *\n)*|\1 SPDX-License-Identifier: GPL-2.0-only\n\n|' $(cat filelist) Change-Id: Ia01908544f4b92a2e06ea621eca548e582728280 Signed-off-by: Patrick Georgi <pgeorgi@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/41178 Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-05-08mainboard/*/*/*.asl: Replace GPLv2 long form headers with SPDX headerElyes HAOUAS
Change-Id: I5970cd188d06214d410949f4a3f8816c85c39451 Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr> Reviewed-on: https://review.coreboot.org/c/coreboot/+/41141 Reviewed-by: Angel Pons <th3fanbus@gmail.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-05-08mainboard/*/*.spd.hex: Replace GPLv2 long form headers with SPDX headerElyes HAOUAS
Change-Id: I3eb39d985f2712ab0a7a5a76b06ed625eb51c9d0 Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr> Reviewed-on: https://review.coreboot.org/c/coreboot/+/41140 Reviewed-by: Angel Pons <th3fanbus@gmail.com> Reviewed-by: Frans Hendriks <fhendriks@eltan.com> Reviewed-by: Wim Vervoorn <wvervoorn@eltan.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-05-08mb/google/reef: add G2 TS support for snappyKevin Chiu
Add G2 GTCH7503 HID TS support spec from G2: G7500 / Ver.1.2 (3, April, 2018) BUG=b:155827595 BRANCH=master TEST=emerge-snappy coreboot Change-Id: I151bf141148f4f00b3dadd9c44ab3a6b7731cde1 Signed-off-by: Kevin Chiu <Kevin.Chiu@quantatw.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/41090 Reviewed-by: Martin Roth <martinroth@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-05-07mb/x9scl/early_init: Remove unused includesElyes HAOUAS
Change-Id: I455a43ab6c4931a4fb1f717a65013b6b7cefb777 Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr> Reviewed-on: https://review.coreboot.org/c/coreboot/+/40827 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Angel Pons <th3fanbus@gmail.com>
2020-05-06treewide: replace GPLv2 long form headers with SPDX headerPatrick Georgi
This replaces GPLv2-or-later and GPLv2-only long form text with the short SPDX identifiers. Commands used: perl -i -p0e 's|/\*[*\n\t ]*This program is free software[:;].*you.*can.*redistribute.*it.*and/or.*modify.*it.*under.*the.*terms.*of.*the.*GNU.*General.*Public.*License.*as.*published.*by.*the.*Free.*Software.*Foundation[;,].*version.*2.*of.*the.*License.*or.*(at.*your.*option).*any.*later.*version.+This.*program.*is.*distributed.*in.*the.*hope.*that.*it.*will.*be.*useful,.*but.*;.*without.*even.*the.*implied.*warranty.*of.*MERCHANTABILITY.*or.*FITNESS.*FOR.*A.*PARTICULAR.*PURPOSE..*.*See.*the.*GNU.*General.*Public.*License for more details.[\n\t ]*\*/|/* SPDX-License-Identifier: GPL-2.0-or-later */|s' $(cat filelist) perl -i -p0e 's|/\*[*\n\t ]*This program is free software[:;].*you.*can.*redistribute.*it.*and/or.*modify.*it.*under.*the.*terms.*of.*the.*GNU.*General.*Public.*License.*as.*published.*by.*the.*Free.*Software.*Foundation[;,].*version.*2.+This.*program.*is.*distributed.*in.*the.*hope.*that.*it.*will.*be.*useful,.*but.*;.*without.*even.*the.*implied.*warranty.*of.*MERCHANTABILITY.*or.*FITNESS.*FOR.*A.*PARTICULAR.*PURPOSE..*.*See.*the.*GNU.*General.*Public.*License for more details.[\n\t ]*\*/|/* SPDX-License-Identifier: GPL-2.0-only */|s' $(cat filelist) perl -i -p0e 's|/\*[*\n\t ]*This program is free software[:;].*you.*can.*redistribute.*it.*and/or.*modify.*it.*under.*the.*terms.*of.*the.*GNU.*General.*Public.*License.*version.*2.*as.*published.*by.*the.*Free.*Software.*Foundation[.;,].+This.*program.*is.*distributed.*in.*the.*hope.*that.*it.*will.*be.*useful,.*but.*;.*without.*even.*the.*implied.*warranty.*of.*MERCHANTABILITY.*or.*FITNESS.*FOR.*A.*PARTICULAR.*PURPOSE..*.*See.*the.*GNU.*General.*Public.*License for more details.[\n\t ]*\*/|/* SPDX-License-Identifier: GPL-2.0-only */|s' $(cat filelist) perl -i -p0e 's|/\*[*\n\t ]*This software is licensed under.*the.*terms.*of.*the.*GNU.*General.*Public.*License.*version.*2.*as.*published.*by.*the.*Free.*Software.*Foundation,.+This.*program.*is.*distributed.*in.*the.*hope.*that.*it.*will.*be.*useful,.*but.*;.*without.*even.*the.*implied.*warranty.*of.*MERCHANTABILITY.*or.*FITNESS.*FOR.*A.*PARTICULAR.*PURPOSE..*.*See.*the.*GNU.*General.*Public.*License for more details.[\n\t ]*\*/|/* SPDX-License-Identifier: GPL-2.0-only */|s' $(cat filelist) Change-Id: I7a746088a35633c11fc7ebe86006e96458a1abf8 Signed-off-by: Patrick Georgi <pgeorgi@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/41066 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: David Hendricks <david.hendricks@gmail.com> Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
2020-05-06treewide: move copyrights and authors to AUTHORSPatrick Georgi
Also split "this is part of" line from copyright notices. Change-Id: Ibc2446410bcb3104ead458b40a9ce7819c61a8eb Signed-off-by: Patrick Georgi <pgeorgi@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/41067 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: David Hendricks <david.hendricks@gmail.com> Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
2020-05-06treewide: Move "is part of the coreboot project" line in its own commentPatrick Georgi
That makes it easier to identify "license only" headers (because they are now license only) Script line used for that: perl -i -p0e 's|/\*.*\n.*This file is part of the coreboot project.*\n.*\*|/* This file is part of the coreboot project. */\n/*|' # ...filelist... Change-Id: I2280b19972e37c36d8c67a67e0320296567fa4f6 Signed-off-by: Patrick Georgi <pgeorgi@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/41065 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: David Hendricks <david.hendricks@gmail.com> Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Angel Pons <th3fanbus@gmail.com>
2020-05-06soc/intel/tgl: Synchronize GPIO ASL table with Linux kernelShaunak Saha
Kernel pinctrl driver changed for Tiger Lake and went to old scheme. Kernel patch: https://chromium-review.googlesource.com/c/chromiumos/ third_party/kernel/+/2116670 BUG=b:151683980 BRANCH=none TEST=Build and boot tgl board. In /sys/kernel/debug/pinctrl verify INTC34C5:00 listing all the pins. Cq-Depend:chromium:2116670 Change-Id: I9f1d399ff7380125ad5b935f9590a7d9cc442b04 Signed-off-by: Shaunak Saha <shaunak.saha@intel.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/39801 Reviewed-by: Furquan Shaikh <furquan@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-05-06mb/google/dedede: Enable PMC, P2SB and PCH SPI in the devicetreeKarthikeyan Ramasubramanian
BUG=None TEST=Build and boot the mainboard. Change-Id: I1aae4adf1c13fd4ff58aa38a877f34e142f320f1 Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/41037 Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org> Reviewed-by: Aamir Bohra <aamir.bohra@intel.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-05-06mb/purism/librem_skl: select DRIVERS_GENERIC_CBFS_SERIALMatt DeVillier
This driver was previously added for another out-of-tree Librem device, but forgot to switch over the librem_skl boards to use it. Remove duplicate functionality from mainboard.c and delete the empty file. Test: build/boot Librem 13v2 and verify serial number read from CBFS via dmidecode. Signed-off-by: Matt DeVillier <matt.devillier@puri.sm> Change-Id: Ide952197335c6bfbad846c6d6f62be5c4c57e2cb Reviewed-on: https://review.coreboot.org/c/coreboot/+/41040 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Patrick Georgi <pgeorgi@google.com>
2020-05-06mb/purism/librem_{bdw,skl}: select MAINBOARD_HAS_TPM1Matt DeVillier
Current model Librems all have a TPM 1.2 module, so select it at the board level to avoid having to do so in .config. Signed-off-by: Matt DeVillier <matt.devillier@puri.sm> Change-Id: Iab8b39c39aef2a3fc182f1a50091f84f2151a394 Reviewed-on: https://review.coreboot.org/c/coreboot/+/41038 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Patrick Georgi <pgeorgi@google.com> Reviewed-by: Michael Niewöhner Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2020-05-05mb/intel/jasperlake_rvp: Configure IP specific GPIOsMaulik V Vaghela
This patch configures all IP related GPIOs as per mainboard schematics. Till now, we were relying on FSP to do IP specific GPIO programming but now we'll program all GPIOs from mainboard. This will remove ambiguity of GPIO programming done by FSP and coreboot will do full GPIO programming Programming GPIOs of following IPs - I2C - Emmc - Display - CPU specific gpio (SLP lines) - Cnvi - SD BUG=None BRANCH=None TEST=compile coreboot and checked that all IP functionality working. Change-Id: I98583b768cbd8ab4af536b31d758cb1cee93edfb Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/40572 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aamir Bohra <aamir.bohra@intel.com> Reviewed-by: V Sowmya <v.sowmya@intel.com> Reviewed-by: Ronak Kanabar <ronak.kanabar@intel.com>
2020-05-04mb/purism/librem_skl: disable serial console outputMatt DeVillier
Librem SKL/KBL boards do not have an exposed serial port interface. Set board Kconfig so that a default built image with Tianocore payload is bootable and doesn't hang due to trying to send data over a non-existant serial port. Test: build/boot librem 13v4 with board defaults + Tianocore Signed-off-by: Matt DeVillier <matt.devillier@puri.sm> Change-Id: I4c3f8a3c1726f804957b06b437b399291854a3f5 Reviewed-on: https://review.coreboot.org/c/coreboot/+/40873 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Angel Pons <th3fanbus@gmail.com> Reviewed-by: Nico Huber <nico.h@gmx.de> Reviewed-by: Michael Niewöhner Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2020-05-04mb/purism/librem_skl: Clean up KconfigMatt DeVillier
Reorder Kconfig selects alphabetically, and select the correct SoC for each variant (even though it currently makes no difference). Signed-off-by: Matt DeVillier <matt.devillier@puri.sm> Change-Id: I46f651a530ef0ed617dd1f3eee077e84279a40f2 Reviewed-on: https://review.coreboot.org/c/coreboot/+/40913 Reviewed-by: Angel Pons <th3fanbus@gmail.com> Reviewed-by: Nico Huber <nico.h@gmx.de> Reviewed-by: Michael Niewöhner Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-05-04mb/purism/librem_skl: rename variant directoriesMatt DeVillier
Since the same variant dirs are used by multiple versions of the same board, drop the v2/v3 labels. Signed-off-by: Matt DeVillier <matt.devillier@puri.sm> Change-Id: Id913e31ab52043e49769be9d3ebf6e71ecb0c856 Reviewed-on: https://review.coreboot.org/c/coreboot/+/40912 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Michael Niewöhner
2020-05-04mb/purism/librem_skl: Convert to use override devicetreeMatt DeVillier
Since the variants' devicetrees are almost identical, convert to using an overridetree setup for simplicity. Signed-off-by: Matt DeVillier <matt.devillier@puri.sm> Change-Id: I3dac62a649e12ea2498d3ecafe03fd0d62af5f2b Reviewed-on: https://review.coreboot.org/c/coreboot/+/40911 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Angel Pons <th3fanbus@gmail.com>
2020-05-04mb/purism/librem_skl: Fix CLKREQ for 15v3 NVMeMatt DeVillier
Per the schematics, SRCCLKREQ2# is used for the NVMe and should be enabled. Enable CLKREQ for PCIe RP9, and adjust comments to indicate correct value used per schematic. Test: build/boot Librem 15v3 with NVMe drive, verify drive identified properly and no errors in boot log. Signed-off-by: Matt DeVillier <matt.devillier@puri.sm> Change-Id: I159cb7ce1f5195d95c0229490c3bbde26edbd375 Reviewed-on: https://review.coreboot.org/c/coreboot/+/40950 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Michael Niewöhner Reviewed-by: Nico Huber <nico.h@gmx.de> Reviewed-by: Angel Pons <th3fanbus@gmail.com>
2020-05-04mb/purism/librem_skl: drop SataSpeedLimit restrictionMatt DeVillier
SataSpeedLimit was set to 3Gbps to work around issues which are now known to be the result of incorrect FSP behavior. Since SataPwrOptEnable is now set at the SoC level and ensures the SIR registers are correctly programmed, we can re-enable 6Gbps operation without errors. Test: build/boot Librem 13v2 with both m.2 and 2.5" SATA drives, check dmesg for errors. Change-Id: I3565dc063724ad288ef92361942fcdc14daac17e Signed-off-by: Matt DeVillier <matt.devillier@puri.sm> Reviewed-on: https://review.coreboot.org/c/coreboot/+/40909 Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Michael Niewöhner Reviewed-by: Angel Pons <th3fanbus@gmail.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-05-04soc/intel/skl: always enable SataPwrOptEnableMichael Niewöhner
For unknown reasons FSP skips a whole bunch of SIR (SATA Initialization Registers) when SataPwrOptEnable=0, which currently is the default in coreboot and FSP. Even if FSP's default was 1, coreboot would reset it. This can lead to all sorts of problems and errors, for example: - links get lost - only 1.5 or 3 Gbps instead of 6 Gbps - "unaligned write" errors in Linux - ... At least on two boards (supermicro/x11-lga1151-series/x11ssm-f and purism/librem13v2) SATA is not working correctly and showing such symptoms. To let FSP correctly initialize the SATA controller, enable the option SataPwrOptEnable statically. There is no valid reason to disable it, which might break SATA, anyway. Currently, there are no reported issues on CML and CNL, so a change there could not be tested reliably. SKL/KBL was tested successfully without any noticable downsides. Thus, only SKL gets changed for now. Change-Id: I8531ba9743453a3118b389565517eb769b5e7929 Signed-off-by: Michael Niewöhner <foss@mniewoehner.de> Reviewed-on: https://review.coreboot.org/c/coreboot/+/40877 Reviewed-by: Matt DeVillier <matt.devillier@gmail.com> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-05-04mb/up/squared: Fix eMMC speed for UP2 with EDK2Patrik Tesarik
Since commit 402fe20e (mb/up/squared: Add mainboard) the UP2's eMMC maximum host speed was reduced to DDR50, because HS200 showed I/O errors in the host kernel. We found out that with EDK2 master the correct Host Speed could not be set properly during EDK2 platform init. Therefore eMMC would not show up for boot device selection. This commit sets the eMMC MaxHostSpeed to the designed max value of the used eMMC on the UP2 board and furthermore drops the override from the ramstage.c. It's already set in the devicetree.cb. Though CRC errors are still visible in EDK II debug logs, no other negative effects have been observed. Signed-off-by: Patrik Tesarik <mail@patrik-tesarik.de> Change-Id: I8d53204d8a776efd560fbdea918f83e180813179 Reviewed-on: https://review.coreboot.org/c/coreboot/+/40403 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Angel Pons <th3fanbus@gmail.com>
2020-05-04mb/google/dedede: Read DRAM part number from CBIMarco Chen
The index of MEM_STRAPS will be migrated from per DRAM part number to per DRAM characteristic therefore one index mapped to a single SPD binary can represent to multiple DRAM part numbers as long as their characteristic is the same for DRAM controller to support. In this case, the real DRAM part number would be provisioned in the CBI instead of SPD in the factory flow. As a result, we need to extract DRAM part number from CBI. BUG=b:152019429 BRANCH=None TEST=1. provision dram_part_num field of CBI 2. check DRAM part number is correct in SMBIOS for memory device Change-Id: I40780a35e04efb279591e9db179cb86b5e907c0d Signed-off-by: Marco Chen <marcochen@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/40836 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
2020-05-04mb/**/dsdt.asl: Drop unused BRIGHTNESS_{UP,DOWN}Angel Pons
It is only used with the Lenovo-specific H8 EC code. Change-Id: If3b209a9ab82a07ce7b4450d8a0b62a1ca86a95c Signed-off-by: Angel Pons <th3fanbus@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/40865 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
2020-05-04treewide: Drop ACPI_VIDEO_DEVICE macroAngel Pons
It was always defined to the same value, and only used twice. Change-Id: I2736eb7ea2cf15475f7bb99d7d12450730eb8be0 Signed-off-by: Angel Pons <th3fanbus@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/40864 Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-05-04mb/**/dsdt.asl: Drop unused ACPI_VIDEO_DEVICEAngel Pons
It is only used with the Lenovo-specific H8 EC code. Change-Id: I596d4d19277555894ab728e32a44e34a5a21e21d Signed-off-by: Angel Pons <th3fanbus@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/40863 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
2020-05-04asus/p2b: Enable IDE and UDMA for all variantsKeith Hui
There's no reason not to. Change-Id: I12c9e0f66c437d8add5c4096fd2a5e747d082799 Signed-off-by: Keith Hui <buurin@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/40961 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Patrick Georgi <pgeorgi@google.com>
2020-05-02mb/asus/p8h61-m_pro: Disable SVID LDNAngel Pons
The SVID functionality is not used on this mainboard. Turn it off. Change-Id: Iea891975b32d24f54edec9d8c36391ec60a37d0c Signed-off-by: Angel Pons <th3fanbus@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/40739 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
2020-05-02mb/asus/p8h61-m_pro: Disable SB-TSI base addressAngel Pons
SB-TSI is specific to AMD platforms, but this is an Intel board. Change-Id: I5eb7e3bc920103279dfca3a9ec14a41666404993 Signed-off-by: Angel Pons <th3fanbus@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/40738 Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Felix Held <felix-coreboot@felixheld.de> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-05-02mb/asus/p8h61-m_pro: Fix function of pin 70Angel Pons
The board uses the pin for Deep S5, but the code was setting 3VSBSW. Change-Id: I81c865358002e6af500658efea851ab8c8202950 Signed-off-by: Angel Pons <th3fanbus@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/40737 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
2020-05-02acpi: Move ACPI table support out of arch/x86 (3/5)Furquan Shaikh
This change moves all ACPI table support in coreboot currently living under arch/x86 into common code to make it architecture independent. ACPI table generation is not really tied to any architecture and hence it makes sense to move this to its own directory. In order to make it easier to review, this change is being split into multiple CLs. This is change 3/5 which basically is generated by running the following command: $ git grep -iIl "arch/acpi" | xargs sed -i 's/arch\/acpi/acpi\/acpi/g' BUG=b:155428745 Change-Id: I16b1c45d954d6440fb9db1d3710063a47b582eae Signed-off-by: Furquan Shaikh <furquan@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/40938 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
2020-05-02mb/asus/p2b*: Get rid of power button deviceKeith Hui
These boards have the same issue as [27272]: Currently, two power buttons are exposed in ACPI, and detected by the operating system. > As per the ACPI specification, there are two types of power button > devices: > 1. Fixed hardware power button > 2. Generic hardware power button > > Fixed hardware power button is added by the OSPM if POWER_BUTTON flag > is not set in FADT by the BIOS. This device has its programming model > in PM1x_EVT_BLK. All ACPI compliant OSes are expected to add this > power button device by default if the power button FADT flag is not > set. > > On the other hand, generic hardware power button can be used by > platforms if fixed register space cannot be used for the power button > device. In order to support this, power button device object with HID > PNP0C0C is expected to be added to ACPI tables. Additionally, > POWER_BUTTON flag should be set to indicate the presence of control > method for power button. > > [i440BX] mainboards implemented the generic hardware power button in > a broken manner i.e. power button object with HID PNP0C0C is added to > ACPI however none of the boards set POWER_BUTTON flag in FADT. This > results in Linux kernel adding both fixed hardware power button as > well as generic hardware power button to the list of devices present > on the system. Though this is mostly harmless, it is logically > incorrect and can confuse any userspace utilities scanning the ACPI > devices. Hardware tests on the P2B-LS shows the generic hardware power button is not working anyway - with FADT power button flag set, the board could not power off with the button. This change removes the generic hardware power button from all P2B mainboards and relies completely on the fixed hardware power button. TEST=Booted on P2B-LS, Linux detects only fixed hardware power button, button still powers off. [27272]: https://review.coreboot.org/27272 Change-Id: I0f5b7aaf32366360de3cce58cd742651a2bb46ba Signed-off-by: Keith Hui <buurin@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/40007 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Angel Pons <th3fanbus@gmail.com>
2020-05-02mb/google/reef: Add and use VBTMatt DeVillier
Add VBT file, and override use via Kconfig since all Reef variants use the same VBT file. VBT extracted from firmware in ChromeOS recovery image. Test: built/boot google/reef w/FSP display init Change-Id: I31156ec7371c0443719fdd9ddac6ed4960c83767 Signed-off-by: Matt DeVillier <matt.devillier@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/40926 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Nico Huber <nico.h@gmx.de> Reviewed-by: Angel Pons <th3fanbus@gmail.com>
2020-05-02mb/purism/librem_bdw: Convert to use override devicetreeMatt DeVillier
Since the variants' devicetrees are almost identical, convert to using an overridetree setup for simplicity. Signed-off-by: Matt DeVillier <matt.devillier@puri.sm> Change-Id: I07fb5a09e578bf299081b26e010317385a6c5f7f Reviewed-on: https://review.coreboot.org/c/coreboot/+/40915 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Michael Niewöhner Reviewed-by: Angel Pons <th3fanbus@gmail.com>
2020-05-02mb/purism/librem_bdw: Clean up 15v2 devicetreeMatt DeVillier
The Librem 15v2 only uses SATA ports 0/1, so the DTLE settings for ports 2/3 have no consequence. Drop them to make overridetree conversion cleaner. Signed-off-by: Matt DeVillier <matt.devillier@puri.sm> Change-Id: I4145feecb389be90f317249426e58752c03aef76 Reviewed-on: https://review.coreboot.org/c/coreboot/+/40914 Reviewed-by: Angel Pons <th3fanbus@gmail.com> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-05-02mainboard/google/kahlee: Add hook for early wlan rst gpio initKevin Chiu
Base on the grunt board schematic, gpio70 is an alternative way for wlan rst. Add hook for variants to override default state. BUG=b:154357210,b:154848243 BRANCH=master TEST=emerge-grunt coreboot Signed-off-by: Kevin Chiu <Kevin.Chiu@quantatw.com> Change-Id: Ic3f1c016357dd5090e6adedf96e7593abff29a0c Reviewed-on: https://review.coreboot.org/c/coreboot/+/40944 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Martin Roth <martinroth@google.com>
2020-05-02payloads/seabios: Add Hardware IRQ KconfigMatt DeVillier
Certain boards require SeaBIOS' HARDWARE_IRQ option to be deselected in order for the platform to boot. Add a Kconfig to allow selection of HARDWARE_IRQ enablement, and write to SeaBIOS' .config file in cases where it needs to be disabled. Deselect the option for google/rambi variants so they boot with boards defaults. Test: build/boot google/clapper, verify board boots vs hanging at boot menu prompt. Change-Id: I23e9b30d2d1042c86bd10f134d6fe361edaf8cb2 Signed-off-by: Matt DeVillier <matt.devillier@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/39869 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Angel Pons <th3fanbus@gmail.com>
2020-05-02mb/google/reef: add default non-ChromeOS FMAPMatt DeVillier
Add a FMAP which supports SMMSTORE and non-ChromeOS payloads, since Apollo Lake-based devices like Reef cannot use an automatically-generated FMAP due to strict layout requirements. Change-Id: If570f92f4f81c0e29777c87756fc5e45af549064 Signed-off-by: Matt DeVillier <matt.devillier@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/40907 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Angel Pons <th3fanbus@gmail.com>
2020-05-02mb/supermicro/x11: drop DeepSx config from devicetreeMichael Niewöhner
Drop the DeepSx config as it's unsupported and disabled for the boards. Change-Id: I91cd15b26a41f376561630cf45ffa192745eae84 Signed-off-by: Michael Niewöhner <foss@mniewoehner.de> Reviewed-on: https://review.coreboot.org/c/coreboot/+/40858 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Patrick Georgi <pgeorgi@google.com> Reviewed-by: Angel Pons <th3fanbus@gmail.com>
2020-05-01mb/intel/cedarisland_crb: Enable P2SB deviceAndrey Petrov
Enable P2SB in static device tree so that hide/unhide trick works. Change-Id: I7dc20b001605b715155d333a07580e21a5f24136 Signed-off-by: Andrey Petrov <anpetrov@fb.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/40918 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Maxim Polyakov <max.senia.poliak@gmail.com> Reviewed-by: Angel Pons <th3fanbus@gmail.com>
2020-05-01mb/intel/cedarisland_crb: Populate 2-socket parameters for FSP-MAndrey Petrov
These parameters were found to work fine for 2-socket configuration, for FSP based on tag 16.D.21. Signed-off-by: Andrey Petrov <anpetrov@fb.com> Change-Id: I466a7f2951ef307036ddaed0be0aacf98dd2710f Reviewed-on: https://review.coreboot.org/c/coreboot/+/40917 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Maxim Polyakov <max.senia.poliak@gmail.com> Reviewed-by: Angel Pons <th3fanbus@gmail.com>
2020-05-01md/tiogapass: move all *.h to dir and make them globalMaxim Polyakov
It is necessary to rename the file gpio.h so that there are no conflict with another file (src/include/gpio.h) Change-Id: I4e3ef5882d6cb0ddbcb8357b54106ff2f47e4c51 Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/40733 Reviewed-by: Andrey Petrov <andrey.petrov@gmail.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-05-01xeon_sp, ocp/tiogapass: remove unused FSP-style GPIO defsMaxim Polyakov
Change-Id: I8599dca99c1f34e3937c5b77b3505815ce625b46 Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/39453 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Angel Pons <th3fanbus@gmail.com>
2020-05-01mb/ocp/tiogapass: fix advanced _PAD_CFG_STRUCT macros in configMaxim Polyakov
If the current pad configuration can not be defined using standard macros from the gpio_defs.h [1], then the intelp2m utility generates "advanced" _PAD_CFG_STRUCT() macros. However, often this configuration in the vendor’s firmware is erroneous. Change the extended macros to standard ones taking into account the information based on the schematic diagram and the previous GPIO configuration for FSP-M [2]. [1] src/soc/intel/common/block/include/intelblocks/gpio_defs.h [2] src/mainboard/ocp/tiogapass/skxsp_tp_gpio.h Change-Id: I56e45b1df77acbdd67e6325c3745a7ad137f8805 Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/40732 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Andrey Petrov <andrey.petrov@gmail.com>
2020-05-01mb/ocp/tiogapass: rework GPIOs configuration using macrosMaxim Polyakov
This format of PCH GPIOs configuration, unlike the raw DW0 and DW1 registers values from the inteltool dump, is more understandable and makes the code much cleaner. The gpio.h file with PAD_CFG macros was automatically generated using the util/intelp2m [1] utility: ./intelp2m -p lbg -file tiogapass/vendorbios/inteltool_gpio.log According to the documentation [2], the Host Software Pad Ownership register only affects the pads that are configured as input (GPI). The intelp2m utility takes this into account when converting macros and ignores bits from this register for the corresponding pads. [1] https://review.coreboot.org/c/coreboot/+/35643 [2] Intel Document Number: 549921 Change-Id: I21e98721e58b00be9196927837daa2b5d2560822 Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/40731 Reviewed-by: Andrey Petrov <andrey.petrov@gmail.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-05-01mb/tiogapass: use common driver to configure GPIOMaxim Polyakov
According to changes in the soc/xeon_sp code [1,2], server motherboards with Lewisburg PCH can use the soc/intel/common/gpio driver to configure GPIO controller. This patch adds pads configuration map, which has the format required by the GPIO driver. The data for this was taken from the inteltool register dump with AMI firmware. The gpio.h file with pad configuration was generated automatically using the util/intelp2m [3]: ./intelp2m -raw -p lbg -file tiogapass/vendorbios/inteltool_gpio.log [1] https: //review.coreboot.org/c/coreboot/+/39425 [2] https: //review.coreboot.org/c/coreboot/+/39428 [3] https: //review.coreboot.org/c/coreboot/+/35643 Change-Id: I818d040fa33f3e7b94b73c9bbbafca5df424616d Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/39427 Reviewed-by: Andrey Petrov <andrey.petrov@gmail.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-05-01mb/ocp/sonorapass: Populate FSP-M parametersAndrey Petrov
Since CPX FSP headers are not released yet, populate certain settings with hard-coded offsets. Provided values are probably not correct and I do not understand what they mean and there is no documentation available yet. However they were found to work to a certain degree. TEST=tested on OCP Sonora Pass EVT Change-Id: I0f78cde69cb8a49a388a412b97bf8713e5b380ea Signed-off-by: Andrey Petrov <anpetrov@fb.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/40554 Reviewed-by: Andrey Petrov <andrey.petrov@gmail.com> Reviewed-by: Maxim Polyakov <max.senia.poliak@gmail.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-05-01mb/ocp/sonorapass: Add Sonora PassRyback Hung
Just a minimal set of board files needed to get it to boot in 1 CPU mode. Signed-off-by: Ryback Hung <ryback.hung%quantatw.com@gtempaccount.com> Change-Id: Ia7b45c78b38d091bd9535899b681746e13efb4fe Reviewed-on: https://review.coreboot.org/c/coreboot/+/40469 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Maxim Polyakov <max.senia.poliak@gmail.com> Reviewed-by: Andrey Petrov <andrey.petrov@gmail.com>
2020-05-01mb/google/dedede: Fix crossystem wpsw_cur errorSubrata Banik
Add GPIO_PCH_WP (GPP_C11) to associate GPP_PCH_WP with community zero. TEST=Build coreboot, flash, boot to and log into kernel, execute "wp enable" in console, execute "crossystem" at kernel prompt and verify that "wpsw_cur" shows as being "1", Execute "wp disable" in console, execute "crossystem" at kernel prompt and verify "wpsw_cur" is 0. Change-Id: Ie4ae1365a7611b8be3e795798c171e3f7ea9e417 Signed-off-by: Subrata Banik <subrata.banik@intel.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/40744 Reviewed-by: Usha P <usha.p@intel.com> Reviewed-by: Maulik V Vaghela <maulik.v.vaghela@intel.com> Reviewed-by: Angel Pons <th3fanbus@gmail.com> Reviewed-by: Karthik Ramasubramanian <kramasub@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-05-01mb/google/deltaur: Add BT reset gpioEric Lai
Harrison Peak (HrP) 9560 module needs a reset pin for BT power sequence. BUG=b:155248677 TEST=Boot into OS and check BT is functional. Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com> Change-Id: I55ed1b095ba53c414c44088f4a6e7720b970e2f2 Reviewed-on: https://review.coreboot.org/c/coreboot/+/40831 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2020-05-01mb/google/deltaur: Update USB/WWAN configIvy Jian
Update USB3 ports configuration as schematics design. BUG=b:155026295 TEST=Boot into OS and check WWAN device detected by lsusb. Signed-off-by: Ivy Jian <ivy_jian@compal.corp-partner.google.com> Change-Id: Icb938e5a9c05fcc9772219b081a6f05334261baf Reviewed-on: https://review.coreboot.org/c/coreboot/+/40818 Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-05-01mainboard/google/kahlee: move specific setting to variantKevin Chiu
Separate specific setting to variant from baseboard. baseboard/romstage.c in current release is only utilized by careena, we could remove it from the rest of variant build. BUG=b:154357210,b:154848243 BRANCH=master TEST=emerge-grunt coreboot Change-Id: I658526e44aadc47bdc5538f506a1bfe2e5f20f63 Signed-off-by: Kevin Chiu <Kevin.Chiu@quantatw.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/40796 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Martin Roth <martinroth@google.com>
2020-05-01mb/google/octopus/variants/bobba: Disable XHCI LFPS power managementSheng-Liang Pan
LTE module is lost after idle overnight, with this workaround, host will not initiate U3 wakeup at the same time with device, which will avoid the race condition. Disable XHCI LFPS power management. If the option is set in the devicetree, the bits[7:4] in XHCI MMIO BAR + offset 0x80A4 (PMCTRL_REG) will be updated from default 9 to 0. BUG=b:146768983 BRANCH=octopus TEST=build coreboot with DisableXhciLfpsPM being set to 1 and flash the image to the device. Run following command to check if bits[7:4] is set 0: >iotools mmio_read32 "XHCI MMIO BAR + 0x80A4" Signed-off-by: Pan Sheng-Liang <sheng-liang.pan@quanta.corp-partner.google.com> Change-Id: Ib8e5ae79e097debf0c75ead232ddbb2baced2a2a Reviewed-on: https://review.coreboot.org/c/coreboot/+/40303 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Marco Chen <marcochen@google.com> Reviewed-by: Henry Sun <henrysun@google.com> Reviewed-by: Justin TerAvest <teravest@chromium.org>
2020-05-01mb/google/volteer/malefor: Enable touch screenWilliam Wei
Enable Goodix touch screen and ensure it works properly. BUG=b:154191288 TEST=FW_NAME=malefor emerge-volteer coreboot chromeos-bootimage Boot to kernel and check the Goodix touch screen function. Signed-off-by: William Wei <wenxu.wei@bitland.corp-partner.google.com> Change-Id: I236ac56dd0a1817092151bae93e699115ba88e4c Reviewed-on: https://review.coreboot.org/c/coreboot/+/40598 Reviewed-by: Alex Levin <levinale@google.com> Reviewed-by: Aaron Durbin <adurbin@chromium.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-05-01mb/purism/librem_skl: Use ACPI backlight controlsBenjamin Doron
Enables ACPI backlight controls. Change-Id: Iccf50f427b7555ee1a3ef9cc11a89d532789ac54 Signed-off-by: Benjamin Doron <benjamin.doron00@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/40145 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Wim Vervoorn <wvervoorn@eltan.com> Reviewed-by: Frans Hendriks <fhendriks@eltan.com> Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
2020-05-01mb/google/hatch/vr/puff: Add psys_pmax calculationTim Chen
This patch adds psys_pmax calculation. There are two types of power sources. One is barrel jack and the other is USB TYPE-C. The voltage level is fixed for a barrel jack while TYPE-C may vary depending on power ratings. We need to get voltage information from EC and calculate correct psys_pmax value. The psys_pmax needs to be set before FSP-S since FSP-S will handle the setting passing to pcode, so move the routine ahead to variant_ramstage_init. BUG=b:151972149 TEST=emerge-puff coreboot chromeos-bootimage check firmware log and ensure psys_pmax is passed to FSP check the data from dump_intel_rapl_consumption in the OS and ensure the power data is close to an external power meter. Change-Id: Iff767d4b44a01e766258345545438a54a16d1af5 Signed-off-by: Tim Chen <tim-chen@quanta.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/40828 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Edward O'Callaghan <quasisec@chromium.org>
2020-05-01mb/google/dedede: Enable USB port for camera supportIan Feng
Support USB Chicony user facing camera. BUG=b:155109736 BRANCH=None TEST=Build and Boot waddledoo board and able to capture image using user facing camera. Signed-off-by: Ian Feng <ian_feng@compal.corp-partner.google.com> Change-Id: I7580a58086977e239dca49c1def4f03583831662 Reviewed-on: https://review.coreboot.org/c/coreboot/+/40774 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Justin TerAvest <teravest@chromium.org> Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
2020-05-01mb/intel/jasperlake_rvp: Select PcieRpClkReqDetect in device treeMeera Ravindranath
This CL selects the PcieRpClkReqDetect for the required root ports which is needed to allow proper clksrc gpio configuration. Also, sets the unused PcieClkSrcUsage to 0xFF. BUG=None BRANCH=None TEST=Build and boot jslrvp with NVMe Change-Id: Ie4ae1365a7621b8be3b795798c171e3f7ea9e487 Signed-off-by: Meera Ravindranath <meera.ravindranath@intel.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/40758 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Subrata Banik <subrata.banik@intel.com> Reviewed-by: V Sowmya <v.sowmya@intel.com> Reviewed-by: Ronak Kanabar <ronak.kanabar@intel.com> Reviewed-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
2020-05-01src: Remove not used 'include <smbios.h>'Elyes HAOUAS
Change-Id: I12345a5b6c9ce94ca9f8b555154b2278a8ff97bf Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr> Reviewed-on: https://review.coreboot.org/c/coreboot/+/39816 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Patrick Georgi <pgeorgi@google.com> Reviewed-by: Nico Huber <nico.h@gmx.de> Reviewed-by: Angel Pons <th3fanbus@gmail.com>
2020-05-01mb/google/dedede: Remove pad termination for RAM_STRAP_4Karthikeyan Ramasubramanian
The stuffed resistor straps are weaker compared to the internal pull-up. This can cause the GPIO to read '1' always. Remove the internal pull-up. Also read the GPIO only on the boards where the board version is populated. BUG=b:154301008 TEST=Build and boot the mainboard. Change-Id: Ib640211b9f50dfb0174a570eda1625bacbebb855 Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/40531 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Furquan Shaikh <furquan@google.com>
2020-05-01Helios: Update DPTF settings for smooth fan speed controlSumeet R Pawnikar
Update DPTF settings for smooth fan speed control. BRANCH=firmware-hatch-12672.B BUG=b:154074920 TEST=Built and test on Helios system Change-Id: I3f4d9fd9e17541dd5fb7982a8b43a039c41cba87 Signed-off-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/40530 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
2020-05-01mb/google/dedede: Enable camera support for waddledooPandya, Varshit B
BUG=None BRANCH=None TEST=Build and Boot waddledoo board and able to capture image using world facing camera. Change-Id: I51dcf96a82535fc1e0b9247fd52af919885575e5 Signed-off-by: Pandya, Varshit B <varshit.b.pandya@intel.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/40476 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aamir Bohra <aamir.bohra@intel.com> Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
2020-05-01mb/google/dedede: Add ACPI support for cameraPandya, Varshit B
1. Add support as per the schematics 2. Add 2 Ports and 2 Endpoints 3. Add support for OTVI8856 and OTVI5676 4. Add ON and OFF logic as Power Rails are same for both sensor BUG=None BRANCH=None TEST=Build and Boot waddledoo board and able to capture image using world facing camera. Change-Id: Ic8687bce4896d9fc17b2190b8d11618af3515cc1 Signed-off-by: Pandya, Varshit B <varshit.b.pandya@intel.com> Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/39360 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aamir Bohra <aamir.bohra@intel.com> Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
2020-05-01mb/google/dedede: add new variant for wheeliePeichao Wang
Add initial support for wheelie variant board. BUG=b:154664137 BRANCH=None TEST=build Change-Id: Id638e987f45c247dae824f221a38ccf32626572f Signed-off-by: peichao.wang <peichao.wang@bitland.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/40587 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Marco Chen <marcochen@google.com> Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
2020-05-01mb/google/nightfury: Tune the usb2_port[0] strengthSeunghwan Kim
Update usb2 port strength parameter for usb2_port[0] to improve SI. BUG=b:154668734 BRANCH=firmware-hatch-12672.B TEST=Built and checked SI margin of USB2 ports Signed-off-by: Seunghwan Kim <sh_.kim@samsung.corp-partner.google.com> Change-Id: I8b4b58a67dc0835a677770a2968e8d8d61e0374f Reviewed-on: https://review.coreboot.org/c/coreboot/+/40622 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
2020-05-01mb/ocp/tiogapass: Update UPD IIO bifurcation at run-timeJohnny Lin
Update UPD IIO bifurcation at run-time according to different Riser cards. For detail please reference Facebook Server Intel Motherboard v4.0, Sec. 10.1.2 Riser card types. With the engineering build FSP, it can only configure IIO for one socket so my local test needs to remove all socket1 elements from tp_iio_bifur_table. This change relies on [1] and need to add GPP_C15 and GPP_C16 to early_gpio_table for gpio configuration in bootblock. [1] https://review.coreboot.org/c/coreboot/+/39427/ Tested=OCP Tioga Pass can see socket0 IIO being updated with an engineering build FSP. Change-Id: I8e63a233a2235cd45b14b20542e6efab3de17899 Signed-off-by: Johnny Lin <johnny_lin@wiwynn.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/39895 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Maxim Polyakov <max.senia.poliak@gmail.com>
2020-04-30mb/cedarisland_crb: rework GPIOs configuration using macrosMaxim Polyakov
This format of PCH GPIOs configuration, unlike the raw DW0 and DW1 registers values from the inteltool dump, is more understandable and makes the code much cleaner. The gpio.h file with PAD_CFG macros was automatically generated using the util/intelp2m [1] utility: ./intelp2m -p lbg -file cedarisland/vendorbios/inteltool_gpio.log According to the documentation [2], the Host Software Pad Ownership register only affects the pads that are configured as input. The intelp2m utility takes this into account when converting macros and ignores bits from this register for the corresponding pads. [1] https://review.coreboot.org/c/coreboot/+/35643 [2] Intel Document Number: 549921 Change-Id: Id671a9021a8313d8c3359b89c2934b929bcab1a4 Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/40736 Reviewed-by: Andrey Petrov <andrey.petrov@gmail.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-04-30mb/cedarisland_crb: exclude GPIOs reconfiguration by FSP-MMaxim Polyakov
We should be sure that after romstage the pads will be configured according to the config from gpio.h only. This patch sets the GPIO configuration from gpio.h using the soc/intel/common/gpio.c driver again in ramstage. [1] https://review.coreboot.org/c/coreboot/+/40730 Change-Id: Ic49e504d96fe4fd44434e7b981f8d8d9e76880ef Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/40735 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Andrey Petrov <andrey.petrov@gmail.com>
2020-04-30mb/intel/cedarisland_crb: use common driver to configure GPIOMaxim Polyakov
According to changes in the soc/xeon_sp code [1,2], server motherboards with Lewisburg PCH can use the soc/intel/common/gpio driver to configure GPIO controller. This patch adds pads configuration map, which has the format required by the GPIO driver. The data for this was taken from the inteltool register dump with vendors firmware. The gpio.h file with pad configuration was generated automatically using the util/intelp2m [3]: ./intelp2m -raw -p lbg -file cedarisland/vendorbios/inteltool_gpio.log [1] https: //review.coreboot.org/c/coreboot/+/39425 [2] https: //review.coreboot.org/c/coreboot/+/39428 [3] https: //review.coreboot.org/c/coreboot/+/35643 Change-Id: I90b91e6dbf8c65c747d0e0d94c61023e610f93ab Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/40734 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Andrey Petrov <andrey.petrov@gmail.com>
2020-04-30mb/amd/padmelon: Remove PS/2 keyboard driver selectionPaul Menzel
Most payloads, like GRUB, SeaBIOS and Linux, are able to initialize the PS/2 keyboard themselves, so coreboot does not need to initialize it. Therefore, this option should not be hard-coded for the mainboard, and be left for the user to select. Change-Id: Ibfb7efa22c525e60399afc198af6632330faaac3 Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de> Reviewed-on: https://review.coreboot.org/c/coreboot/+/40752 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
2020-04-30mb/pcengines/apu1: Remove PS/2 keyboard driver configurationPaul Menzel
Since commit 6aa8c5bc (drivers/pc80: Do not initialize PS2 keyboard by default), the Kconfig option `DRIVERS_PS2_KEYBOARD` already defaults to `n`. So, remove it here, as this option should be user selectable anyway depending on the payload. Change-Id: I3d08fb6bbb3e9d53fd2fed96f26679e8b1e73f8c Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de> Reviewed-on: https://review.coreboot.org/c/coreboot/+/40751 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Michał Żygowski <michal.zygowski@3mdeb.com>
2020-04-30mb/purism/librem_bdw: Remove PS/2 keyboard driver selectionPaul Menzel
Most payloads, like GRUB, SeaBIOS and Linux, are able to initialize the PS/2 keyboard themselves, so coreboot does not need to initialize it. Therefore, this option should not be hard-coded for the mainboard, and be left for the user to select. Change-Id: Iac835d2e7a3232f8e5c76f10984ae3f172f9c0ca Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de> Reviewed-on: https://review.coreboot.org/c/coreboot/+/40750 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Matt DeVillier <matt.devillier@gmail.com> Reviewed-by: Angel Pons <th3fanbus@gmail.com>
2020-04-30mb/ocp/tiogapass: Implement port 80h direct to GPIO and init UART pinsBryantOu
Enable aspeed's function that port 80h direct to GPIO for LED display, refer to section 9.4 Port 80h Direct to GPIO Guide of aspeed's Application Design Guide, also configure GPIO to UART for output serial console messages. Tested=Check if port 80h LED debug card can display POST codes at early stage, and serial console can see the related messages. Change-Id: I087d5a81b881533b4550c193e4e9720a134fb8e7 Signed-off-by: BryantOu <Bryant.Ou.Q@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/40481 Reviewed-by: Patrick Rudolph <patrick.rudolph@9elements.com> Reviewed-by: Andrey Petrov <andrey.petrov@gmail.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-04-30mb/google/voteer: Enable DevSlp for SATA port1Wonkyu Kim
BUG=b:152893285 BRANCH=none TEST=Build and boot to OS volteer with Intel SATA and reboot from OS console Signed-off-by: Wonkyu Kim <wonkyu.kim@intel.com> Change-Id: Ibed8f8c445bf2ac2290ffb670d8dfb83fc960438 Reviewed-on: https://review.coreboot.org/c/coreboot/+/40584 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
2020-04-30mb/google/volteer: Create trondo variantDavid Wu
Create the trondo variant of the volteer reference board by copying the template files to a new directory named for the variant. BUG=b:154678884 BRANCH=None TEST=util/abuild/abuild -p none -t google/volteer -x -a make sure the build includes GOOGLE_TRONDO Change-Id: Ie4f9bfe4798e14f91c6cb439f5c5ab2b9ea52b51 Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/40686 Reviewed-by: Caveh Jalali <caveh@chromium.org> Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-04-30mb/google/puff: update USB2 strengthTim Chen
Based on USB SI report to fine tune the strength for USB2 port0. BRANCH=none BUG=b:153590143 TEST=build and test USB2 port0 function works fine. Change-Id: I070c9e1c8153a680fb8f827889738a764d7ea9f4 Signed-off-by: Tim Chen <tim-chen@quanta.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/40482 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Kangheui Won <khwon@chromium.org> Reviewed-by: Edward O'Callaghan <quasisec@chromium.org>
2020-04-29mb/intel/tigerlake: Include TCSS power managementJohn Zhao
Include TCSS RTD3 into ACPI DSDT table. BUG=b:140290596 TEST=Booted to kernel and verified tcss xhci/pcierp/dma power state D3 entry/exit. Change-Id: I8cc5cfb572e15121059eb1fba41f931c59afbdf6 Signed-off-by: John Zhao <john.zhao@intel.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/40615 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
2020-04-29mb/google/volteer: Include TCSS power managementJohn Zhao
Include TCSS RTD3 into ACPI DSDT table. BUG=b:140290596 TEST=Booted to kernel and verified tcss xhci/pcierp/dma power state D3 entry/exit. Change-Id: Iae31a29eb23f7370737d097dd401f4056b8b7052 Signed-off-by: John Zhao <john.zhao@intel.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/40616 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
2020-04-29mb/google/octopus/variants/garg: update Garfour SKU IDTony Huang
SKUID: 49 - Garfour EVT (touch, TypeA DB) 50 - Garfour EVT (non-touch, HDMI DB) BUG=b:152861752 BRANCH=octopus TEST=emerge-octopus coreboot chromeos-bootimage Change-Id: I656a2bb2404efded6da6697664748b6c8d2ca4e0 Signed-off-by: Tony Huang <tony-huang@quanta.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/40586 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Karthik Ramasubramanian <kramasub@google.com> Reviewed-by: Marco Chen <marcochen@google.com>
2020-04-29soc/amd/hda: Move HDA PCI device from DSDT to SSDTFurquan Shaikh
This change adds support in common block HDA driver to add a PCI device for HDA in SSDT and removes the HDA device from DSDT for Stoneyridge and Picasso. _INI method is still retained in stoneyridge since I am unsure why it was added. In order to support the _INI method, HDA driver makes a callback hda_soc_ssdt_quirks() to allow SoCs to add any quirks required for the HDA device. This callback is implemented by Stoneyridge to provide the _INI method which retains the same functionality for HDA device. This makes it easier to ensure that we don't accidentally make the DSDT and SSDT entries inconsistent w.r.t. ACPI name and scope. BUG=b:153858769,b:155132752 TEST=Verified that audio still works fine on Trembyle. Change-Id: I89dc46b92fdcb785bd37e18f0456935c0e57eff5 Signed-off-by: Furquan Shaikh <furquan@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/40785 Reviewed-by: Aaron Durbin <adurbin@chromium.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-04-29mb/google/hatch/romstage_spd_smbus.c: Fix missing DIMM issueEdward O'Callaghan
Since `commit 0ee9b14c09c` the SPD array is set to NULL if no DIMM is present. This causes failure due to an unconditional use of `blk.spd_array[i]`, : i={0,1}. This validates the spd_array is non-NULL before use otherwise it sets the DIMM as not present. Puff fails boot with the following log: ``` ... SPD: banks 16, ranks 2, rows 16, columns 10, density 8192 Mb SPD: device width 8 bits, bus width 64 bits SPD: module size is 16384 MB (per channel) ASSERTION ERROR: file 'src/soc/intel/cannonlake/cnl_memcfg_init.c', line 47 ``` BUG=b:155220125 BRANCH=none TEST=none Change-Id: I5f47c849344951d53fa8c67e779b7c46d632d124 Signed-off-by: Edward O'Callaghan <quasisec@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/40820 Reviewed-by: Jamie Chen <jamie.chen@intel.com> Reviewed-by: Sam McNally <sammc@google.com> Reviewed-by: Furquan Shaikh <furquan@google.com> Reviewed-by: Daniel Kurtz <djkurtz@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-04-29mb/google/volteer: Work around TPM issue by enabling GPIO PM in S0ixVenkata Krishna Nimmagadda
Setting the default values for GPIO community power management, causes issues in detecting TPM interrupts. So to avoid that GPIO PM has to be disabled in devicetree. But for S0ix it is needed. This patch implements a workaround in ASL code to enable GPIO PM on S0ix entry and disable it on S0ix exit. This patch adds the following three platform specific methods. 1. MS0X to enable power management features for GPIO communities on entry and on exit, it disables them. 2. MPTS to enable power management features for GPIO communities when preparing to sleep. 3. MWAK to disable power management features for GPIO communities on waking up. BUG=b:148892882 BRANCH=none TEST="Boot with this change on volteer proto1 and check for GPIO community config with debugger" Signed-off-by: Venkata Krishna Nimmagadda <venkata.krishna.nimmagadda@intel.com> Change-Id: If522c82c0069a4bf5738beb73a2b4f11ed6f51d3 Reviewed-on: https://review.coreboot.org/c/coreboot/+/40261 Reviewed-by: Nick Vaccaro <nvaccaro@google.com> Reviewed-by: Venkata Krishna Nimmagadda <Venkata.krishna.nimmagadda@intel.com> Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-04-28mb/google/volteer: move mipi_camera.asl to variants foldersNick Vaccaro
Moves mipi_camera.asl from mb/google/volteer/acpi/ to mb/google/volteer/variant/baseboard/include/baseboard/acpi/. Adds mipi_camera.asl to variant/[volteer|ripto]/include/acpi/. Adds new VARIANT_HAS_MIPI_CAMERA Kconfig option. Adds VARIANT_HAS_MIPI_CAMERA for volteer and ripto variants. BUG=b:154648941, b:154646959 TEST="emerge-volteer coreboot chromeos-bootimage", flash and boot Ripto and Volteer to kernel. Change-Id: I2f28243dfb945857d26f27f07968a15a3eeb7a4f Signed-off-by: Nick Vaccaro <nvaccaro@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/40578 Reviewed-by: William Wei <wenxu.wei@bitland.corp-partner.google.com> Reviewed-by: Furquan Shaikh <furquan@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-04-28mb/google/volteer: implement mainboard_get_dram_part_num()Nick Vaccaro
Implements mainboard_get_dram_part_num() to override dram part number with a part number read from CBI. BUG=b:146464098 TEST="emerge-volteer coreboot chromeos-bootimage", flash volteer, boot and log into kernel, execute "mosys memory spd print id" and verify that the memory part number from the cbi gets displayed properly. Change-Id: I3a20691f601cb513ee0936c8d141233c3d06db3d Signed-off-by: Nick Vaccaro <nvaccaro@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/40472 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
2020-04-28device: Constify struct device * parameter to acpi_fill_ssdt()Furquan Shaikh
.acpi_fill_ssdt() does not need to modify the device structure. This change makes the struct device * parameter to acpi_fill_ssdt() as const. Change-Id: I110f4c67c3b6671c9ac0a82e02609902a8ee5d5c Signed-off-by: Furquan Shaikh <furquan@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/40710 Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr> Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-04-28device: Constify struct device * parameter to write_acpi_tablesFurquan Shaikh
.write_acpi_tables() should not be updating the device structure. This change makes the struct device * argument to it as const. Change-Id: I50d013e83a404e0a0e3837ca16fa75c7eaa0e14a Signed-off-by: Furquan Shaikh <furquan@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/40701 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Raul Rangel <rrangel@chromium.org>
2020-04-28mb/google/deltaur: Disable POWER_OFF_ON_CR50_UPDATEEric Lai
This is missing configuration of Wiloc projects. Following Wilco projects configuration. CB:32436 The power architecture on this platform is different than most of our other x86 devices and needs some special handling to ensure it powers up again after an EC reset. BUG=b:150165131 Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com> Change-Id: I6da89de9401793a4e5c56a23c1018527819718cf Reviewed-on: https://review.coreboot.org/c/coreboot/+/40663 Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-04-28mb/google/deltaur: Change H1 I2C speed to STANDARDEric Lai
Currently, Deltaur’s I2C speed has not been tuned yet, so slow down the H1 I2C to avoid I2C error for short term. Error logs: Reading cr50 TPM mode I2C receive timeout I2C read failed: bus 3 addr 0x50 BUG=b:154310066 TEST=Check H1 has no I2C error occurring and can be updated by gsctool. Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com> Change-Id: I85a63c1ab9a51d254873377a36d56823af11f0a9 Reviewed-on: https://review.coreboot.org/c/coreboot/+/40644 Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-04-28mb/google/deltaur: Enable PS/2 keyboardEric Lai
By default, the ACPI status method _STA returns false for the PS/2 keyboard and mouse device of the Wilco EC, so the OS does not enable it. Enable these devices, by defining the macro SIO_EC_ENABLE_PS2K. BUG=b:154790509 TEST=Check Keyboard is functional under OS. Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com> Change-Id: I31c74ddb3608589e5a4753c7e487f250b112bb1e Reviewed-on: https://review.coreboot.org/c/coreboot/+/40745 Reviewed-by: Ivy Jian <ivy_jian@compal.corp-partner.google.com> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-09 17:35:08 +0000