| Age | Commit message (Collapse) | Author |
|---|
|
Define a chip option to explicitly soft reset all enabled GPIOs to
default state.
TEST=boot FreeBSD 11.2 on PC Engines apu1, change GPIO configuration
using nctgpio module and check whether GPIOs are reset after reboot
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Change-Id: Iae4205574800138402cbc95f4948167265a80d15
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38850
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
The 2nd COM port's base address defaults to 0x2f8. Current software
for this system expects the port at 0x3e8.
Configure COMB to use 0x3e8 instead of 0x2f8.
BUG=N/A
TEST=tested on facebook monolith
Change-Id: Ibb462bad5f0594e0b5c8dea6e02cd42d58d999ab
Signed-off-by: Wim Vervoorn <wvervoorn@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39499
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Remove unused SMM_STORE space and use it for RW_LEGACY area
BUG=None
TEST=None
Change-Id: I5724b860271025e8cb8b320ecbd33352ef779660
Signed-off-by: Meera Ravindranath <meera.ravindranath@intel.com>
Signed-off-by: Ronak Kanabar <ronak.kanabar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38273
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-by: V Sowmya <v.sowmya@intel.com>
|
|
The concerned GPIO is configured as an open drain at the Embedded
Controller side without an external pull-up. This causes leakage in the
PP3300_A rail. So configure the GPIO to have a weak internal pull-up at
the SoC side.
BUG=b:151680590
TEST=Build the mainboard. Ensure that there are no leakages in the
PP3300_A rail.
Change-Id: I5553cf40adb92edc0fecab5c875ec8d72063ba7b
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39796
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
We should only define function to get lid switch and recovery mode
switches when CHROMEEC_SWITCHES is not available. Correct this to avoid
compilation issues
BUG=None
BRANCH=None
TEST=jslrvp code compilation is fine
Change-Id: I2445d40da1540c9d8c8c5fc845a4f38a5abf983e
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39585
Reviewed-by: Ronak Kanabar <ronak.kanabar@intel.com>
Reviewed-by: V Sowmya <v.sowmya@intel.com>
Reviewed-by: Aamir Bohra <aamir.bohra@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add memory initialization parameters for Jasper Lake RVP boards
Jasper Lake RVP supports two variants, one with memory LPDDR4
and another with DDR4
Based on board id, mainboard will pass correct memory parameters
to the fsp.
BUG=None
BRANCH=None
TEST=Check compilation for Jasper Lake RVP and check memory training passes.
Change-Id: Idc92363a2148990df16c2068c7986013d015f604
Signed-off-by: Ronak Kanabar <ronak.kanabar@intel.com>
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39195
Reviewed-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-by: V Sowmya <v.sowmya@intel.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The ACPI Spec 2.0 states, that Processor declarations should be made
within the ACPI namespace \_SB and not \_PR anymore. \_PR is deprecated
and is removed here.
Additionally add processor scope patching for P-State SSDT created by
AGESA, becasue AGESA creates the tables with processors in \_PR scope.
TEST=boot Debian Linux on PC Engines apu2, check dmesg that there are
no errors, decompile ACPI tables with acpica to check whether the
processor scope is correct and if IASL does not complain on wrong
checksum, run FWTS
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Change-Id: I35f112e9f9f15f06ddb83b4192f082f9e51a969c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39698
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
A bigger than zero value of bmc_boot_timeout must be set
for KCS ipmi_get_bmc_self_test_result() to run, otherwise
the self test result will be error and won't write SMBIOS
type 38 table. Here we set 60 seconds as the maximal self
test timeout.
Tested=Check if the BMC IPMI response data and SMBIOS type
38 on OCP Tioga Pass are correct or not.
Signed-off-by: Johnny Lin <johnny_lin@wiwynn.com>
Change-Id: I3678973736a675ed22b5bc9da20a2ca947220f4b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38995
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
|
|
Nuvoton NCT5104d has no LDN 0xe according to its datasheet.
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Change-Id: I0d34218d88b779b08c380d2396ff9ab9253597fa
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38851
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
|
|
Enable ASPM L0s and L1, Common Clock and Clock Power Management for
all PCIe ports.
TEST=boot Debian linux and check new PCIe capabilities appear in lspci
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Change-Id: I0a4c83731742f31ab8ef1d326e800dfdc2abb1b7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39704
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
PC Engines apu2 had many problems with PCIe cards detection. The cards
were inconsistently detected when booted from G3, S5 or after a reboot.
AGESA can reset PCIe slots using GPIO via callback. Use it to reset the
slots that support using GPIO as reset signal.
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Change-Id: I8ff7db6ff85cce45b84729be905e6c895a24f6f2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39703
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
The `link_frequency_270_mhz` setting was originally used by the native
graphics init code for Sandy/Ivy Bridge, which is long gone.
The value of this information (which board had it set) is questionable.
The only board that had an LVDS panel and set it to 0 was the ThinkPad
L520, where native graphics init was never reported to work. Also, the
native graphics init only used it for calculations, but never confi-
gured the hardware to use a specific frequency. A look into the docu-
mentation also doesn't reveal any straps that could be used to confi-
gure it.
Change-Id: Ieceaa13e4529096a8ba9036479fd84969faebd14
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39763
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Alexander Couzens <lynxis@fe80.eu>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
_DCS, _DGS and _DSS are required by specification. However,
we never implemented them properly, and no OS driver com-
plained yet. So we stub them out and keep the traditional
behavior in case an OS driver checks for their existence.
The old implementations also only returned static values as
there never was any write to their GNVS variables. The TRAP()
that was called in one place is actually implemented by some
ThinkPad's SMI handler as docking event. However, as the call
precedes these SMI handlers in coreboot history, it's most
likely an accident.
Change-Id: Ib0b9fcdd58df254d3b2290900e3bc206a7abd92d
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39726
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
|
|
The format for VPD has changed s.t. the first NIC should
always have a zero concat to the end. drivers/net supports
this with the workaround of setting the idx to 1.
The longer term fix is to adjust all the respective boards
to shift back by one and adjust drivers/net friends to
remove the 'special casing' of idx == 0.
Background:
https://chromeos.google.com/partner/dlm/docs/factory/vpd.html#field-ethernet_macn
BUG=b:152157720
BRANCH=none
TEST=none
Change-Id: I510428c555b92398a5199b346dffb85d38495d74
Signed-off-by: Edward O'Callaghan <quasisec@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39768
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sam McNally <sammc@google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Change-Id: I385339761b3e1b5dcadb67b8ca29b1518c2db408
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39702
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
The ACPI Spec 2.0 states, that Processor declarations should be made
within the ACPI namespace \_SB and not \_PR anymore. \_PR is deprecated
and is removed here for Intel CPUs only.
Tested on:
* X11SSH (Kabylake)
* CFL Platform
* Asus P8Z77-V LX2 and Windows 10
FWTS does not return FAIL anymore on ACPI tests
Tested-by: Angel Pons <th3fanbus@gmail.com>
Change-Id: Ib101ed718f90f9056d2ecbc31b13b749ed1fc438
Signed-off-by: Christian Walter <christian.walter@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37814
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
A certain somebody (that would be me) forgot how to count, it seems.
Change-Id: Iac0ac5827ca242c465a2e8be92a823c8fc9b2935
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39741
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Coalescing is not needed, as all PCIe ports are used.
Change-Id: Icf31f6672e0a54d119a6537da1b52c42f9cee823
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39740
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
IRQ 0x70 was not declared for device 2e.7, and coreboot whined about it.
Change-Id: If40aa390722cf253169003129b31f20543fde5dd
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39739
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Linux does not handle either value in any special way, though.
Change-Id: I833cb94e65b9ddfb79edbcdd0216c70740aa4a16
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39738
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Add camera ACPI configuration for Ripto/Volteer
BUG=None
BRANCH=None
TEST=Build and boot Ripto or Volteer. Start camera app and able to
capture images.
Signed-off-by: Daniel Kang <daniel.h.kang@intel.com>
Change-Id: I2b47ccd989192273a29f09bf097e12e357929334
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39684
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
|
|
This is required for PD notifications on the cros_ec driver.
BUG=b:150649744
TEST=Boot volteer with this patch and verify that PD notifier events are
being generated.
Signed-off-by: Prashant Malani <pmalani@chromium.org>
Change-Id: I2e72320b025a3dfa7412181586cb142a4503eda5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39675
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Use information provided by AGESA to fill the SMBIOS memory tables.
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Change-Id: Id73de7c2b23c6eb71722f1c78dbf0d246f429c63
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38343
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Update Audio AIC UPD settings and gpio pad configs for Tiger Lake.
BUG=none
BRANCH=none
TEST=Build and boot tigerlake rvp board
Signed-off-by: Srinidhi N Kaushik <srinidhi.n.kaushik@intel.com>
Change-Id: I45935b79f6fa4ad66238eead9258a4f15feec508
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39466
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
|
|
Camera ACPI had an incorrect board config flag for TGL-UP4.
BUG=None
BRANCH=None
TEST=Build and boot TGLRVP-UP3 or UP4. Start camera app and able to
capture images.
Signed-off-by: Daniel Kang <daniel.h.kang@intel.com>
Change-Id: Ided0e146a9240169d3f1f27a86218ac1a942b899
Signed-off-by: Daniel Kang <daniel.h.kang@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39682
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
|
|
Micron memory part uses SPD Index 0.
BUG=b:152005386
TEST=Build the mainboard.
Change-Id: I990a95b13d636148f0f922fd5c6d4e489d35ed2c
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39709
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Change-Id: I487fb53bb2b011d214f002fc200ade2f128a4cc6
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39030
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
1. Configure Audio GPIOs.
2. Set i2c4 configuration.
3. Update PCH HDA configuration
TEST=Verify codecs gets listed with aplay -l command.
Signed-off-by: Aamir Bohra <aamir.bohra@intel.com>
Signed-off-by: Yong Zhi <yong.zhi@intel.com>
Change-Id: Ic0516c7a8fee79ce17343a7f42895d6ef534fec9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39285
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Add HID field in max98357a_config and allow mainboards to set it.
Signed-off-by: Aamir Bohra <aamir.bohra@intel.com>
Change-Id: I22d2d078a9a4eb6ab330da8439737ff5133086d4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39286
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I005bf205142d4d8c5e12378f33d2100d278fa174
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39661
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Change-Id: I78f06b54a6a03d565cf86f1d7bdf37965c3f6ad0
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39660
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
They are already in AUTHORS.
Change-Id: I315c0c57babfa239e3d7c501a4183b8996999e6e
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39659
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Updating devicetree to enable ELAN touchpad and ELAN touchscreen on nightfury
BUG=none
BRANCH=firmware-hatch-12672.B
TEST=built and verified touchpad and touchscreen worked
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.com>
Change-Id: Ieba6558ce3897ce2f95f51ed667465d84b4ab189
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39602
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
The VGA port has the DDC on port B.
Select the correct Kconfig and fix graphics init failing on VGA.
Tested on HP Z220, libgfxinit reports success and SeaBIOS is displayed
on the connected VGA monitor.
Change-Id: Ie5ec1a2d4606a21e1dc4217ff6fefe5ee35ac543
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39629
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
This is a µATX mainboard with a LGA1150 socket and four DDR3 DIMM slots.
Working:
- All four DIMM slots
- Serial port to emit spam
- Some USB ports
- Integrated graphics (libgfxinit)
- HDMI and DVI
- Intel GbE
- All PCIe ports
- Both PCI ports behind the ASM1083 PCI bridge
- At least one SATA port
- RAM initialization with MRC binary
- Flashing with flashrom
- S3 suspend/resume
- Rear audio output
- VBT
- SeaBIOS to boot Arch Linux
Not working:
- PS/2 keyboard (detected as mouse)
Untested:
- The other audio jacks
- S/PDIF
- VGA
- EHCI debug
- Front USB headers
- Non-Linux OSes
- TPM header
- Parallel port
Change-Id: I10a16dfc56f2aa88648c8aaaba4feab40c491504
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36770
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Adds GMM into the baseboard of Octopus
For GLK, PCI device 3 is GMM according to
Document#: 569262(Glk EDS Vol-1 rev2-7)
Related to Gerrit review 39579
BUG=b:151115705
BRANCH=None
TEST=Flashed final image on Chromebook
Change-Id: I75b4a835c18c5eeb542b7f7b89deea45a31e47bd
Signed-off-by: Franklin He <franklinh@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39600
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
The integrated BT is routed via USB2 port 8, add USB configuration
to support integrated BT enumeration.
Change-Id: I46d8c92ba57cd72a91ee15ef4d11f07824c29e9a
Signed-off-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39471
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
They're listed in AUTHORS and often incorrect anyway, for example:
- What's a "Copyright $year-present"?
- Which incarnation of Google (Inc, LLC, ...) is the current
copyright holder?
- People sometimes have their editor auto-add themselves to files even
though they only deleted stuff
- Or they let the editor automatically update the copyright year,
because why not?
- Who is the copyright holder "The coreboot project Authors"?
- Or "Generated Code"?
Sidestep all these issues by simply not putting these notices in
individual files, let's list all copyright holders in AUTHORS instead
and use the git history to deal with the rest.
Change-Id: I426518e8e18de1c8efcfb7ecb0835df3e257dca1
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39608
Reviewed-by: Wim Vervoorn <wvervoorn@eltan.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: David Hendricks <david.hendricks@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
They're listed in AUTHORS and often incorrect anyway, for example:
- What's a "Copyright $year-present"?
- Which incarnation of Google (Inc, LLC, ...) is the current
copyright holder?
- People sometimes have their editor auto-add themselves to files even
though they only deleted stuff
- Or they let the editor automatically update the copyright year,
because why not?
- Who is the copyright holder "The coreboot project Authors"?
- Or "Generated Code"?
Sidestep all these issues by simply not putting these notices in
individual files, let's list all copyright holders in AUTHORS instead
and use the git history to deal with the rest.
Change-Id: I09cc279b1f75952bb397de2c3f2b299255163685
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39607
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: David Hendricks <david.hendricks@gmail.com>
|
|
They're listed in AUTHORS and often incorrect anyway, for example:
- What's a "Copyright $year-present"?
- Which incarnation of Google (Inc, LLC, ...) is the current
copyright holder?
- People sometimes have their editor auto-add themselves to files even
though they only deleted stuff
- Or they let the editor automatically update the copyright year,
because why not?
- Who is the copyright holder "The coreboot project Authors"?
- Or "Generated Code"?
Sidestep all these issues by simply not putting these notices in
individual files, let's list all copyright holders in AUTHORS instead
and use the git history to deal with the rest.
Change-Id: I18e513cefc373b1cd70d31d1159928cc948a8476
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39609
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: David Hendricks <david.hendricks@gmail.com>
Reviewed-by: Tristan Corrick <tristan@corrick.kiwi>
|
|
They're listed in AUTHORS and often incorrect anyway, for example:
- What's a "Copyright $year-present"?
- Which incarnation of Google (Inc, LLC, ...) is the current
copyright holder?
- People sometimes have their editor auto-add themselves to files even
though they only deleted stuff
- Or they let the editor automatically update the copyright year,
because why not?
- Who is the copyright holder "The coreboot project Authors"?
- Or "Generated Code"?
Sidestep all these issues by simply not putting these notices in
individual files, let's list all copyright holders in AUTHORS instead
and use the git history to deal with the rest.
Change-Id: I57fc98788bb47df16d6aedd0f0701e9991801743
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39606
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Wim Vervoorn <wvervoorn@eltan.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: David Hendricks <david.hendricks@gmail.com>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-by: Tristan Corrick <tristan@corrick.kiwi>
|
|
* Change power sequence to make it closer to ov8856 sensor
data sheet version 2
* Handle different PWREN GPIO pins for up3 and up4
* Add link frequencies definitions to sensor side
* Clean up format
BUG=None
BRANCH=None
TEST=Build and boot TGLRVP U or Y. Start camera app and able to
capture images.
Signed-off-by: Daniel Kang <daniel.h.kang@intel.com>
Change-Id: Ic11a36f1f82fe425c1a5796847ce020007064403
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39529
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Method RAOW is assuming that the first argument is a Field object
and writing to it expecting the register to get updated. However,
the callers are passing in the value of the Field object instead.
This eventually is resulting the IMGCLK not getting enable/disabled on the
platform.
Fix this by sending the exact address of the register to be updated.
Also MCCT was setting the clock frequency in both case i.e, Clock Enable
and Disable. Split the MCCT method in two, MCON and MCOF to fix the sequencing
like below
MCON:
Set frequency
Enable clock
MCOF:
Disable clock
Also, make use of MCON and MCOF methods for camera clock control in tglrvp.
This is to avoid the buildbot marking the patch unstable.
BUG=None
BRANCH=None
TEST=Build and Boot waddledoo board and verified that IMGCLKOUT for
world facing camera is enabled/disabled and able to capture images.
Build and Boot Tiger Lake RVP board and verified that IMGCLKOUT for
world facing camera is enabled/disabled and able to capture images.
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Change-Id: I8b886255d5f38819502ae1f4af0851b5a0922b22
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39498
Reviewed-by: Srinidhi N Kaushik <srinidhi.n.kaushik@intel.com>
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Foob360 would prefer to use different SAR values. Since Foob360
sku id is 9.
BUG=b:149362272
BRANCH=octopus
TEST=build
Signed-off-by: peichao.wang <peichao.wang@bitland.corp-partner.google.com>
Change-Id: I8cc5d73629990f19d2c1044debdba4990c54d07e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39424
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marco Chen <marcochen@google.com>
|
|
These platforms use the standard fixed function power button
and do not need a second power button device declared or the
kernel will end up with two devices reporting the same event.
Same change was applied to all google mainboards in
CB:27272 which contains more detail.
Change-Id: I17c85e43493530d04f4fa13f33bec6d027cb3147
Signed-off-by: Matt DeVillier <matt.devillier@puri.sm>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39577
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add initial support for waddledee variant board.
BUG=b:151576904
TEST=Build the mainboard and variant board.
Change-Id: I20d41fbbb78c7fd2f964a97ffebbc9c3bbfb1c5c
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39580
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
BRANCH=none
BUG=b:145946347
TEST=boot to OS with TGL RVP UP3,
then copied ISH firmware to host file system /lib/firmware/intel/tglrvp_ish.bin
check "dmesg |grep ish", it shows:
ish-loader: ISH firmware intel/tglrvp_ish.bin loaded
cros_ec_ishtp: Chrome EC device registered
Those means shim loader in coreboot has loaded ISH firmware, and
firmware is running successfully.
Signed-off-by: Hu, Hebo <hebo.hu@intel.com>
Signed-off-by: li feng <li1.feng@intel.com>
Change-Id: I1ee8050aef6ec0828f16ef2695b5347278caa820
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39481
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The X210 EC reports battery values in broken mAh. These have to be
adjusted by 10000 * DGVO, as documented in
https://github.com/torvalds/linux/blob/master/drivers/acpi/battery.c.
Taken from https://github.com/harrykipper/coreboot, commits
2f68f138adb25605e5715896636cf33f6de5bd95
c1c72cc43708a6647f263a767c39cf3072908e20
Change-Id: Ie097272443b18b16c3937034f874d3b5a6bdd62a
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39142
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
- Add USB ports for SD card reader, fingerprint reader,
and internal port.
- Enable PcieRpClkReqSupport on NVMe root port,
correct values for ClkReq/ClkSrc.
- Improve comment for M.2-2230 USB port (BT)
Parts derived from x210_test branch of HarryKipper's repo:
https://github.com/harrykipper/coreboot
Change-Id: Ib64629ada4726e5edc080608f71a51f56a9b747c
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39143
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Derived from x210_test branch of HarryKipper's repo:
https://github.com/harrykipper/coreboot
Test: build/boot x210, test eDP, MiniDP, VGA outputs
Change-Id: Ie2b79b236a458ebd243c992d6e615e41930eeb50
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39106
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
The 51nb X210 is a replacement motherboard for Thinkpad X200/X201 systems,
based on a modern Kabylake CPU. It also ships with no firmware protection,
(IFD is fully unlocked, no protected regions are set, no Bootguard),
making it an ideal coreboot target. This port is based on the support for
the Skylake-based Purism Librem 13v3, with the following significant
changes:
* EC firmware is contained within the system SPI flash, and so a blob of
EC firmware must be injected to a defined location during image build.
* GPIO layout is different - this is currently just a raw import of the
GPIO configuration from the vendor firmware
* The system has two DIMMs, so an additional SPD address has been added
* The USB port layout is different
* The EC must be enabled at boot time through SuperIO-style logical device
configuration
* EC register layout is different, necessitating changes in the ACPI tables
* The HDA pins are different
* The genx_dec config is different
All hardware appears to work as expected, although the SD reader is
untested.
Signed-off-by: Matthew Garrett <mjg59@google.com>
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Change-Id: If74621e76d703f629b54f1feb1acfc95cc72d183
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32531
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
This is new Elan touch screen IC, which includes touch panel and USI pen.
BUG=b:151514167
TEST=build bios and verify touch screen works fine
Signed-off-by: Tommie Lin <tong.lin@bitland.corp-partner.google.com>
Change-Id: I98801b8c31812637f71d7eaaa0f12b47901dc47a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39494
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
The code is for Arrandale CPUs, whose System Agent is Ironlake.
This change simply replaces `nehalem` with `ironlake` and `NEHALEM`
with `IRONLAKE`. The remaining `Nehalem` cases are handled later, as
changing some of them would impact the resulting binary.
Tested with BUILD_TIMELESS=1 without adding the configuration options
into the binary, and packardbell/ms2290 does not change.
Change-Id: I8eb96eeb5e69f49150d47793b33e87b650c64acc
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38941
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Consistently use the official uppercase spelling.
Change-Id: I2e2d62389d1b965f4a391080a10e7f97fa787d14
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39350
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Enable CNVi in devicetree and add gpio pad configs for CNVi
BUG=none
BRANCH=none
TEST=Build and boot tglrvp
Signed-off-by: Srinidhi N Kaushik <srinidhi.n.kaushik@intel.com>
Change-Id: I71146960e0d53dae87946a0365dac6f224a72391
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39464
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Caveh Jalali <caveh@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add Palkia as a variant of Hatch.
BUG=b:150254194
BRANCH=none
TEST=none
Signed-off-by: Kane Chen <kane_chen@pegatron.corp-partner.google.com>
Change-Id: I6a303d9fc2be9ea358ad66cd648738187c974193
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38860
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Volteer uses 4 bits (hardware straps) to indicate what memory
configuration the board is populated with (i.e. which SPD file
to use for the populated memory). This allows for only 16
different SPDs for supporting Volteer and all future variants of
Volteer. Currently, each memory chip needs its own SPD file, so we
can only support 16 different memory chip options for Volteer and
all of its variants.
Generic SPD files are just SPD files that have been stripped down
to contain only fields that are important for the memory controller
(strips out items like vendor info, for example). Using generic SPD
files allows for more than 16 different memory options given it's no
longer a 1-to-1 mapping as similar memory modules from different
vendors can share the same generic SPD file.
BUG=b:147857288
TEST="emerge-volteer coreboot chromeos-bootimage", flash ripto and
verify ripto boots to kernel and "cat /proc/meminfo" reports 8GB
of memory.
Change-Id: I17bd4f4a00b4e3bbaf845d6d321962c11569a186
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39423
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Turn on CNVi device. Turn on PCIe Root port that hosts WLAN device.
Configure PCIe Clk Source and Clk Request mapping. Configure GPIOs used
for WLAN - both CNVi and M.2.
BUG=None
TEST=Build the mainboard.
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Change-Id: I9bb8e57cdb688bc544929c94af380b9ef1d936a2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39115
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Disable the BT module in bootblock and enable it in ramstage. This
allows for loading the BT firmware during reboot.
TEST=Build and boot the mainboard.
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Change-Id: I0406a68ffcab2675a1aedb212cb7c8508a5b61fc
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39446
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Enable GEO SAR function.
BUG=b:150347463
BRANCH=drallion
TEST=NA
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: Iace9aa0245840328aa13920512747ca7f60e85dd
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39467
Reviewed-by: Mathew King <mathewk@chromium.org>
Reviewed-by: Ivy Jian <ivy_jian@compal.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Update GPIO reset type from PLTRST to DEEP.
DEEP setting is more conservative for S3/S4/S5.
Detail information is bug.
BUG=b:151305120
TEST=Build and boot to OS
Signed-off-by: Wonkyu Kim <wonkyu.kim@intel.com>
Change-Id: Ie7d08560ea2ef3623bbd4734b30c80e707869c7b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39476
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Srinidhi N Kaushik <srinidhi.n.kaushik@intel.com>
Reviewed-by: Caveh Jalali <caveh@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Provide settings for configuring the link between HD-Audio controller
and display unit for purposes of HDMI/DP Audio playback.
BUG=b:144708516, b:148385924
TEST=none
Change-Id: I225faac68729b28be65b4d8f1f83769a874f84ff
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39356
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Early ec sync needs to be disabled for EFS2 to function.
BUG=b:151115320
BRANCH=none
TEST=none
Change-Id: I384d072d9614a5cd30837f7cdfb777ad5e4f6b19
Signed-off-by: Edward O'Callaghan <quasisec@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39461
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
1. Configure trackpad interrupt GPIO.
2. Set i2c0 configuration.
3. Add trackpad ACPI support.
TEST= Verify trackpad working. Verify I2C SCL frequency below 400Khz
on trackpad operation.
Change-Id: I52c578aef591f5be90fb709bab4c8342ea9729e6
Signed-off-by: Pandya, Varshit B <varshit.b.pandya@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39236
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Create new variant and build for nightfury.
BUG=b:149226871
TEST=FW_NAME="nightfury" emerge-hatch coreboot chromeos-bootimage
Change-Id: If08692f4a2d216c57499098cc0e35abd708d99d4
Signed-off-by: Raymond Chung <raymondchung@ami.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38826
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Shelley Chen <shchen@google.com>
|
|
Limit PcieL1Substate for RP9, RP11 for ES1 NVMe warm reboot workaround.
Reference: #613582 Tiger Lake PCH-LP Sightings Report
issue id #1409566330
BUG=none
BRANCH=none
TEST= boot to OS and check warm reboot with NVMe
Signed-off-by: Wonkyu Kim <wonkyu.kim@intel.com>
Change-Id: Ie85bf71c43427e326ef2ba674da4566f8f51495a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39413
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Srinidhi N Kaushik <srinidhi.n.kaushik@intel.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
|
|
Enable USB ACPI driver. Add ACPI configuration for all the USB ports.
Since one of the USB ports is used for Bluetooth configure the
reset_gpio used by that port.
TEST=Build the mainboard.
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Change-Id: I3e7b8f00102c96dcc295601359d3ecfbcd1bea00
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39422
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
|
|
BUG=b:148604250
BRANCH=none
TEST=Build and test booting TGLRVP form NVMe and Optane
Check PCIe lane configuration
Show all the NVMe devices
lspci -d ::0108
Show all the NVMe devices and be really verbose
lspci -vvvd ::0108
Print PCIe lane capabilities and configurations for all the NVMe devices.
lspci -vvvd ::0108 | grep -e x[124]
Print all the PCIe information of the device ae:00.0
lspci -vvvs ae:
Signed-off-by: Wonkyu Kim <wonkyu.kim@intel.com>
Change-Id: I5fc8fa0897ad006de9ebe20115bf3033e1e1b499
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39233
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Caveh Jalali <caveh@chromium.org>
Reviewed-by: Srinidhi N Kaushik <srinidhi.n.kaushik@intel.com>
|
|
BUG=b:150154457
BRANCH=none
TEST=Build dedede, flash and boot to kernel.
Change-Id: I7248861efd1edd5a0df0e17d39a47c168cab100e
Signed-off-by: Meera Ravindranath <meera.ravindranath@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39348
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Aamir Bohra <aamir.bohra@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
PMC logic shuts down the PCH thermal sensor when CPU is in a C-state and
DTS Temp <= Low Temp Threshold (LTT) in case of Dynamic Thermal shutdown
when S0ix is enabled.
BUG=None
BRANCH=None
TEST=Verified Thermal Device(B0: D18: F0) TSPM offset 0x1c [LTT (8:0)]
value is 0xFE on Drallion.
Change-Id: I146068d8019859be1c27e2a8174dfe7909d42d0a
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39395
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Bora Guvendik <bora.guvendik@intel.com>
|
|
Add LPDDR3 4GB 2133MHz SPD file.
BUG=b:149226871
TEST=Build and check cbfs has the spd.bin
Change-Id: I1598774a87eecc76082286540beadaa3c26eda69
Signed-off-by: Raymond Chung <raymondchung@ami.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39271
Reviewed-by: Shelley Chen <shchen@google.com>
Reviewed-by: Philip Chen <philipchen@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Optane memory module shows up as 2 NVMe devices in x2 config - NVMe
storage device and NVMe Optane memory. Storage device uses rp9 and
optane memory uses rp11. This patch enables rp11. Please note that
these two share clk related pins.
Configuring pciecontroller3 to be set from 2x2. This will by done by
auto detecting optane memory: enabling HybridStorageMode.
BUG=b:148604250
BRANCH=chromeos
TEST='Build, boot and look for two NVMe devices with lspci on Volteer'
Cq-Depend: chrome-internal:2501837
Signed-off-by: Venkata Krishna Nimmagadda <venkata.krishna.nimmagadda@intel.com>
Change-Id: I5430829b496ed275e2e3bda3c0bf21c3d2132628
Reviewed-on: https://chrome-internal-review.googlesource.com/c/chromeos/third_party/coreboot-intel-private/jsl-tgl/+/2424428
Tested-by: Wonkyu Kim <wonkyu.kim@intel.corp-partner.google.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39420
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
Reviewed-by: Caveh Jalali <caveh@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Disable WWAN PCIe to allow WWAN enumerate as USB on Volteer.
BUG=b:146226689
BRANCH=none
TEST=lsusb shows WWAN device
Change-Id: I04e49e3ec989d20ea3469fce06051c475b0ed0c8
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39421
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
During intial UP4 patch, below UP3 patches merged which should be
applied for UP4.
https://review.coreboot.org/c/coreboot/+/39201
https://review.coreboot.org/c/coreboot/+/39229
Merge these patches to UP4
BUG=none
BRANCH=none
TEST=Build TGL UP4
Signed-off-by: Wonkyu Kim <wonkyu.kim@intel.com>
Change-Id: I7b24cb2b0d03309cf67c6c21ddc2031a054f6110
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39419
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Caveh Jalali <caveh@chromium.org>
Reviewed-by: Srinidhi N Kaushik <srinidhi.n.kaushik@intel.com>
Reviewed-by: Shaunak Saha <shaunak.saha@intel.com>
|
|
Change-Id: I219fb2c12bb865288364f6e48b1e3d64c14bc036
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39079
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Change-Id: Idfb8c834ae63226546a4e2860d9b206ba0288718
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39078
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Remove unmaintained and unsupported old ROMCC board.
This board wasn't hooked up for build.
Change-Id: Ie79637c992874bd06009ed9b3e9f470b44e749b7
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39064
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Remove unmaintained and unsupported old ROMCC board.
This board wasn't hooked up for build.
Change-Id: I1bce09ba5041a6636f900de611846467653f35a9
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39069
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Remove unmaintained and unsupported old ROMCC board.
This board wasn't hooked up for build.
Change-Id: Ib4a95c650cc4d1cddc2ba530c12ce448a1943b34
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39068
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Remove unmaintained and unsupported old ROMCC board.
This board wasn't hooked up for build.
Change-Id: Iaa812dc66ddc14c24263a68e73115502ba5e2417
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39066
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
This is required to transmit button information from EC to kernel.
BUG=b:150830342
BRANCH=None
TEST=firmware_ECPowerButton test passes on puff
Change-Id: I10ba9d55e8997ce2412deb0613cfcaa8f24f271d
Signed-off-by: Kangheui Won <khwon@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39391
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Edward O'Callaghan <quasisec@chromium.org>
|
|
Change-Id: Ia31da9997ba46c15cd385bf55e009cf299848b64
Signed-off-by: Praveen Hodagatta Pranesh <praveenx.hodagatta.pranesh@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36423
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I6374bc2d397800d574c7a0cc44079c09394a0673
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37984
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
If we don't pretend to have binaries, there is no need to add fake ones.
This also fixes building the default config.
Change-Id: I8f933f24a734a9ce3d82ef57f7f234ee4dfa86e9
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39383
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: David Hendricks <david.hendricks@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I32fc8a7d3177ba379d04ad8b87adefcfca2b0fab
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/30360
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
|
|
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Change-Id: I03e8e8db5d827fe113280f2a6376d364edf42870
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33839
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
|
|
This change uses drivers/intel/wifi chip for CNVi device and
adds dynamic SSDT entires for CNVi also export wake gpio for CNVi
BUG=none
BRANCH=none
TEST=Build and boot tigerlake rvp board and check for SSDT entries
for CNVi
Signed-off-by: Srinidhi N Kaushik <srinidhi.n.kaushik@intel.com>
Change-Id: Icdbffa0c29c9e0849a6a99f8592b6f35c0bb3207
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39315
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
Reviewed-by: Caveh Jalali <caveh@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
BUG=144874778
TEST=Built with Volteer recipe and verified USB functionality
Change-Id: I6cbdbd8a4f65a0fe19e3fb8d7b60b8b849f104e7
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39357
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Add configuration for all the PCIe Root ports and Clock Source.
Configure the Root Ports as disabled and clock sources as not used.
BUG=None
TEST=Build the mainboard.
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Change-Id: I0a1ad7e056907e454a93f51c84e1d99f08b7bdef
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39166
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This enables display for use by payload.
TEST=Build and boot the mainboard. Ensure that the screens displayed by
payload are visible.
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Change-Id: I5fcd70623b15ae39954242605e75b2c5ce02ff14
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39347
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
BUG=b:150869661
TEST=Build and boot the mainboard. Trigger apreset from EC console.
Trigger reboot from AP console.
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Change-Id: I0d6dd0b4264c11f7ee0ef436cc819b0bb92974f7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39325
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Leave all the GPIOs in not connected state so that they can be
configured depending on the use-case. This is done to park the GPIOs in
a known safe state. This will also help to ensure that the required
GPIOs are configured when the concerned use-cases are enabled.
Below GPIOs are configured in Native Function 1 and are required for
boot-up.
* VCCIN_AUX_VID0
* VCCIN_AUX_VID1
* AP_SLP_S0_L
* PLT_RST_L
* CPU_C10_GATE_L
* GPDs
BUG=None
TEST=Build and boot the mainboard.
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Change-Id: I5293536f66a6b08c9c2d2a6281684755a0c0b1b3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39114
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
BUG=b:147500717
TEST=none
Change-Id: I32fa27b399127dbf8608e0556c77431d2dad652d
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39358
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
- declare the FPMCU interrupt to be level-triggered
- change EC_PCH_WAKE_ODL gpio to native function mode
- corrected spelling of a signal name in a comment
BUG=b:144933687, b:148179954
BRANCH=none
TEST=none
Change-Id: I62da900d0b71139e55b52d06ec09ca25106f73cd
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39337
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Change-Id: I553fd3a89299314a855f055014ca7645100e12e7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32076
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
|
|
This mainboard has the FSB BSEL straps wired to SuperIO GPIOs. They are
set up in romstage, so it makes no sense to clobber the registers with
garbage in ramstage.
Tested, my Asus P5G41T-M LX still boots and it does not need a full
reset on almost every reboot.
Change-Id: I6ea498119df44243ec42e3cb5c2903de32a17373
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39384
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Not all GPIO4 pins on the SuperIO are configured as outputs.
Change-Id: Idf6350551a91c4c1a25a83e3fb9b1a6722a81c36
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39386
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
This mainboard has the FSB BSEL straps wired to SuperIO GPIOs. They are
set up in romstage, so it makes no sense to rewrite their values in
ramstage.
Tested, my Asus P5QPL-AM still boots.
Change-Id: Ic47f96d12420ebcc70ab5cea940c4c09620c03ca
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39385
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Changes allow to use the integrated panel logic (power sequen-
cing and backlight control) for more connectors. The Kconfigs
GFX_GMA_PANEL_1_PORT and GFX_GMA_PANEL_2_PORT can now be set
to any port, e.g.
config GFX_GMA_PANEL_1_PORT
default "DP3"
Now that the panel logic is not tied to the `Internal` port
choice anymore, we can properly split it into `LVDS` and `eDP`.
This also adds Comet Lake PCI IDs which should still work the
same as Kaby and Coffee Lake.
Change-Id: I78b1b458ca00714dcbe7753a7beb4fb05d69986b
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38921
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add LPDDR4 memory configuration for Tiger Lake UP4 platform which
includes
1. DQ/DQs Mapping
2. Board id Support
3. SPD indexing
BUG=none
BRANCH=none
TEST= Build TGL UP4 successfully
Signed-off-by: Srinidhi N Kaushik <srinidhi.n.kaushik@intel.com>
Change-Id: Ibbd7036919c1a91ef12049d2af657f0a3597b57e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39365
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
