| Age | Commit message (Collapse) | Author |
|---|
|
Disable DRRS on Blooguard SKU - 49, 50, 51, 52
BUG=b:142632381
BRANCH=octopus
TEST=emerge-octopus coreboot chromeos-bootimage
check i915_drrs_status shows DRRS supported NO when SKU ID is blooguard.
Cq-Depend: chrome-internal:1983227
Change-Id: I36a313fd2beacb878da7383f733e206067c1c0fb
Signed-off-by: Tony Huang <tony-huang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36015
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Corrected clang issues in fbg1701 directory.
BUG=N/A
TEST=build
Change-Id: I968bf8418aa457a7ebd28096bd92a64211bf86dd
Signed-off-by: Wim Vervoorn <wvervoorn@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35963
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
|
|
This sets up some common default LPC decode ranges in a common place.
This may set up more decode ranges than needed but that typically does
not hurt. Mainboards needing additional ranges can do so in the
mainboard pch_enable_lpc hook.
Change-Id: Ifeb5a862e56f415aa847d0118a33a31537ab8037
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33549
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Port the backlight-PWM handling from Skylake instead of the previously
used Haswell version. We use a 200Hz PWM signal for all boards. Which
is higher than the previous devicetree value, 183Hz, but that was over-
ridden by the VBIOS anyway. 200Hz is still very low, considering LED
backlights, but accurate values are unknown at this time.
Lynx Point, the PCH for Haswell and Broadwell, is a transition point
for the backlight-PWM config. On platforms with a PCH, we have:
o Before Lynx Point:
The CPU has no PWM pin and sends the PWM duty-cycle setting
to the PCH. The PCH can choose to ignore that and use its own
setting (BLM_PCH_OVERRIDE_ENABLE).
We use the CPU setting on these platforms.
o Lynx Point + Haswell:
The CPU has an additional PWM pin but can be set up to send
its setting to the PCH as before. The PCH can still choose
to ignore that.
We use the CPU setting with Haswell.
o Lynx Point + Broadwell:
The CPU can't send its setting to the PCH anymore. BLM_PCH_
OVERRIDE_ENABLE must always be set(!) if the PCH PWM pin is
used (it virtually always is).
We have to use the PCH setting in this case.
o After Lynx Point:
Same as with Broadwell, only BLM_PCH_OVERRIDE_ENABLE is
implied and the bit not implemented anymore.
Change-Id: I1d61d9b3f1802ebe18799fc4d06f1f1d3b54c924
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35897
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
On some configuration coreboot boots too fast and the EC reports the
max temperature, resulting in Linux shutting down immediately.
Change-Id: I610c7c9fbf2130566d3c2c758f1796314d3a0973
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36059
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Alexander Couzens <lynxis@fe80.eu>
|
|
Change-Id: I03461cb9e87b4ddd599e5601637a75b012694e7c
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36047
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Helios adds TEMP_SENSOR4 to the EC ADC2 pin. Add this to
the DPTF.
BRANCH=None
BUG=b:142266102
TEST=`emerge-hatch coreboot`
Verify that Helios builds correctly.
Change-Id: I3bc19f9b9bd644e134987749ad9a4d875ad8b40a
Signed-off-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35920
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Shelley Chen <shchen@google.com>
|
|
Enable wifi sar feature and set wifi sar name for dragonair sku.
BUG=b:142109545
TEST=emerge-hatch coreboot chromeos-bootimage
1. Check wifi_sar-dragonair.hex in /cbfs-rw-raw/dratini
2. Add iwlwifi.debug into kernel params.
3. check SAR value from dmesg only when sku id is 21/22
Change-Id: I0e08610b7c7d2d8da5a749d278bcde26af590e31
Signed-off-by: Wisley Chen <wisley.chen@quantatw.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35807
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
FPMCU_PCH_BOOT1 pin is connected to GPP_C12. So, config GPP_C12.
BUG=b:142188003
TEST=emerge-hatch coreboot
Change-Id: I73a5c3529330ef3e72f4c7d5fcbbd2f6693494d8
Signed-off-by: Wisley Chen <wisley.chen@quantatw.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35845
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
On Hyper-Threading enabled platforms the MSR_PRMRR_PHYS_MASK was written
when already locked by the sibling thread. In addition it loads microcode
updates on all threads.
To prevent such race conditions only call the code on one thread, such
that the MSRs are only written once per core and the microcode is only
loaded once for each core.
Also add comments that describe the scope of the MSR that is being
written to and mention the Intel documents used for reference.
Fixes crash in SGX MP init.
Tested on Supermicro X11SSH-TF.
Change-Id: I7102da028a449c60ca700b3f9ccda9017aa6d6b5
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35312
Reviewed-by: Christian Walter <christian.walter@9elements.com>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The port is based on the x201 / t410s.
2537-vg5 / i5, no discrete gpu
Tested and working:
* Native raminit
* Native gfxinit
* Booting Seabios 1.12.1
* Booting from EHCI
* Running GNU/Linux 5.0.0
* No errors in dmesg
* EHCI debug on the devices left side, bottom-right
* Keyboard
* Fn keys (Mute, Volume, Mic)
* Touchpad
* TPM
* Wifi
* Sound
* USB
* Ethernet
* S3 resume
* VBOOT
Testing in progress.
Untested:
* VGA
* Displayport
* Docking station
Bugs:
* AC adapter can't be read from ACPI
* TPM not working with VBOOT and C_ENV BB
Details for flashing externally:
1. Disconnect all power
2. Connect the external flasher
3. Connect the power cord (This fixes internal power control)
4. Remove the power cord
Change-Id: Id9d872e643dd242e925bfb46d18076e6ad100995
Signed-off-by: Nicolas Reinecke <nr@das-labor.org>
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/11791
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
This does the following:
- Add gen[1-4]_dec options to the devicetree to set up generic LPC
decode ranges in the southbridge code.
- Move setting up some default decode ranges to a common place. If
somehow a board needs to override this behavior it can happen in the
mb_setup_superio() hook (that will be renamed when moving to
C_ENVIRONMENT_BOOTBLOCK).
Change-Id: I3d904b1125bc410c11aa73a89b1969284e88dac1
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35991
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Change-Id: Id8e25caf2868c37c9d7c7717dd908152dfc583a3
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35986
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
A few notable changes:
- Microcode init is done in assembly during the CAR init.
- The DCACHE_BSP_STACK_SIZE is set to 0x2000, which is the same size
against which the romstage stack guards protected.
- The romstage mainboard_lpc_init() hook is removed in favor of the
existing bootblock_mainboard_early_init().
Change-Id: Iccd7ceaa35db49e170bfb901bbff1c1a11223c63
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35951
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Change-Id: I0b1356420c9ae419b2a0a247b9dc6c8e92b7689a
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35966
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Change-Id: Ic56367d64b9304b36f5ba5a4b7d5237574eb73ae
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35965
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Change-Id: Iaf9a4608f1b7d25cf5d8dbe2c1489b3d2d00f25a
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35964
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
The NO_POST option covers more than classical port 80 output, hence
selecting it seems wrong in any case. The default is still rather
user patronizing, but let's keep it.
As a side effect, this fixes the ability to override the default
for NO_POST which Kconfig rejected while these boards selected it.
(Seems like a bug in Kconfig, though.)
Change-Id: I896b08812b1aa6ce249d7acc8073ebcc0f72eace
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35956
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
|
|
Some boards with the G41 chipset lacked programming CIR, so this
change add that to those boards too.
Change-Id: Ia10c050785170fc743f7aef918f4849dbdd6840e
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35795
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
|
|
The vendorcode/eltan mboot and verified boot options only build if a
few other Kconfig options are defined.
Change-Id: Ie333d2fbf294e23ec01df06ee551e2d09541c744
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35954
Reviewed-by: Wim Vervoorn
Reviewed-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The next board rev will have a new option for an Elan touchscreen. Add
support for this in the devicetree, as well as use the 'probed' property
on both touchscreen options.
BUG=b:141957731
BRANCH=none
TEST=compiles (next board rev not available yet)
Change-Id: I135e693304cbb8dffc0caf4c07846033d6802208
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35944
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Shelley Chen <shchen@google.com>
|
|
Update GPIO_138 and GPIO_139 setting to fix EMR function.
BUG=b:141729962,b:141281846
BRANCH=octopus
TEST=verify EMR function in Grob360S.
Change-Id: I28cef592374fb4aeee2f3d3010cc0e237d62a2fd
Signed-off-by: John Su <john_su@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35881
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marco Chen <marcochen@google.com>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Change-Id: If30a17d053da8f0758085fc36469b564d46049cd
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35901
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Load the calibration params from flash first and check the correctness
of the params. If the params have correct format, perform DRAM fast
calibration with these params to reduce bootup time. Otherwise, load the
DRAM blob and perform DRAM full calibration.
Bootup time of DRAM partial calibration:
- 1,349,385 usecs with low frequency
- 924,698 usecs with middle frequency
- 1,270,089 usecs with high frequency
3,544,172 usecs in total.
Bootup time of DRAM fast calibration:
- 216,663 usecs with low frequency
- 328,220 usecs with middle frequency
- 322,612 usecs with high frequency
867,495 usecs in total.
BUG=b:139099592
BRANCH=none
TEST=emerge-kukui coreboot
Change-Id: I8de29b14b1fb24b3b4f351c855c5c4d8f350cc34
Signed-off-by: Huayang Duan <huayang.duan@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35110
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
|
|
Load calibration params from flash. If the format of the params is
correct, use these calibration params for fast calibration to reduce the
bootup time.
Bootup time of DRAM partial calibration:
- 1,349,385 usecs with low frequency
- 924,698 usecs with middle frequency
- 1,270,089 usecs with high frequency
3,544,172 usecs in total.
Bootup time of DRAM fast calibration:
- 216,663 usecs with low frequency
- 328,220 usecs with middle frequency
- 322,612 usecs with high frequency
867,495 usecs in total.
BUG=b:139099592
BRANCH=none
TEST=Boots correctly on Kukui
Change-Id: I9ef4265dd369a1c276bb02294696556df927e7bc
Signed-off-by: Huayang Duan <huayang.duan@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35164
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Drallion uses UART 0 for console, other two variants remain as UART 2.
BUG=b:139095062
TEST=emerge-drallion coreboot chromeos-bootimage.
Console should be visible.
Change-Id: I520a07ad6f755bc2e6481329fc69bef9a36e31e2
Signed-off-by: Bernardo Perez Priego <bernardo.perez.priego@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35785
Reviewed-by: Bora Guvendik <bora.guvendik@intel.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-by: Mathew King <mathewk@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Dratini/Dragonair doesn't support pen insertion/ejection feature,
so remove it.
BUG=b:142159117
TEST=emerge-hatch coreboot
Change-Id: I64859a162d8dc75ffe55d98b72a056dd72e8de75
Signed-off-by: Wisley Chen <wisley.chen@quantatw.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35844
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Shelley Chen <shchen@google.com>
|
|
FreeBSD's sh (basic posix shell) did not interpret the '\%o' escape
in the same way bash/zsh do. As a result, the decoded files ended up
with ASCII numbers instead of the decoded binary data.
Change-Id: I95b414d959e5cd4479fcf100adcf390562032c68
Signed-off-by: Greg V <greg@unrelenting.technology>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35867
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Minimize use of hard-coded value for acpi_table_header->length to soft
code. Replace length of acpi_header_t with sizeof(acpi_fadt_t).
Change-Id: Ibcae72e8f02497719fcd3f180838557e8e9abd38
Signed-off-by: Himanshu Sahdev <himanshusah@hcl.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35540
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
|
|
BUG=b:142131099
BRANCH=None
TEST=powerd_dbus_suspend, ensure DUT in S0ix
touch fp sensor and ensure DUT wakes up in S0
Change-Id: If57094aa1076d79ac0886b71fa5532411bfeb45f
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35903
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
|
|
Change-Id: I67de5260a756fc7b1cf0ec1903bee0058a2dcb06
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35861
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
|
|
The superio driver that was linked in is nct6779d but static
devicetree expected symbol superio_nuvoton_nct5572d_ops.
Change-Id: I648b7680bb39b9ff5b38cc3bd5147bd336e0b282
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35855
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Change-Id: I13c0134b22e2203e6cee6ecafda0dae89e086aff
Signed-off-by: Peter Lemenkov <lemenkov@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34779
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I0a3076780ac5cf183235f06e4c56d0707bf5e6ca
Signed-off-by: Peter Lemenkov <lemenkov@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34123
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Add the missing detect pin to fix Wacom touchscreen function.
BUG=b:140415892,b:138082886
BRANCH=N/A
TEST=N/A
Change-Id: I8a1b48d4d502945b88e38393383512d30b684fa4
Signed-off-by: Frank Wu <frank_wu@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35790
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Applying reset_gpio config of stylus for kohaku. GPP_A19 has been assigned in
the latest schematics.
We would keep GPP_A10 as output high for old revision devices temporarily.
BUG=b:141914474
BRANCH=none
TEST=verified stylus works internally
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.com>
Change-Id: I61f0f9a4378f47bf455f0726d44beeaf2f67197b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35748
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Shelley Chen <shchen@google.com>
|
|
Add PRESERVE to UNIFIED_MRC_CACHE so that we don't retain the memory
training data upon a FW update unless we need to. We have had users
complaining that a 15 second memory training upon update makes them
believe that their device is not booting, thus many of them hard
resetting before bootup.
BUG=b:142084637
BRANCH=None
TEST=flash RW_SECTION_A, RW_SECTION_B, and WP_RO sections and make
sure memory training doesn't occur on following bootup.
Change-Id: Ia5eb228b1f665a8371982544723dab3dfc40d401
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35803
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
After adjustment on Grob360S
I2C0 CLK: 389.9 KHz
BUG=b:141729962
BRANCH=master
TEST=emerge-octopus coreboot chromeos-bootimage
measure by scope with Grob360S.
Change-Id: I6a30257b7978cc8899a55f9fd6ffffe01cb2a851
Signed-off-by: John Su <john_su@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35788
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
|
|
Change-Id: I9ad9294dd2ae3e4a8a9069ac6464ad753af65ea5
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35541
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Add a GPIO table for Monolake to initialize GPIOs with custom board
configurations.
Tested on Monolake.
Change-Id: I74906bf9395a333be6250ffbd181da536e016f30
Signed-off-by: Jingle Hsu <jingle_hsu@wiwynn.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35367
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: David Hendricks <david.hendricks@gmail.com>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
|
|
Change-Id: I3a3174cf20cea60d8b2c4d0311a48ce9ffe1a8a1
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35804
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
This change does the following:
- Move PCH init code from the common romstage to sb code, this allows
for easier reuse in bootblock
- Provide a common minimal LPC io decode setup, mainboards can
override this in the mainboard_lpc_init if required
- Set up LPC generic IO decode up in romstage based on devicetree
settings
- Remove the ramstage LPC generic IO decode from ramstage as this is
now done in romstage.c
- Get rid of unneeded setup of spi_read configuration in BIOS_CNTL as
this is already done in the bootblock.
Change-Id: I3f448ad1fdc445c4c1fedbc8497e1025af111412
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35772
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Move the mainboard_romstage_entry to a common location and provide
mainboard specific callbacks.
Change-Id: Ia827053617cead5d2cf8e9f06cb68c2cbb668ca9
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35771
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
X201 boots fine without it.
Change-Id: I20a8e598b07bf0a059dcb47651d1a26456863673
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35769
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This is based on the sandybridge settings.
The current lookup table comes from the x201 vendor lookup table.
Tested: USB mouse and webcam still work and current registers are the
same as before. USB IR are not but the code follows EDS instead of the
register replay.
Change-Id: Icea9673623a62e7039d5700100a2ee238478abd1
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35762
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The values read back in those ranges are identical before and after
this change and the Lenovo Thinkpad X201 still boots fine.
Change-Id: I406510e0573ac97003da7d97181abdfbfd2a872f
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35760
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The RCBA registers 0x3400-0x3500 are all handled elsewhere
in the code, so no need to have a 'replay' of those.
The remainder now consist of USB setup and undocumented bits
that should likely not be touched at all.
Change-Id: I69fc8a5e16f7cf0e1068d0d2ed678a6c2f6e70a9
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35440
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
This does the following:
- implement a PCH disable function that will be called by the PCI
drivers as part of their chip_ops
- removes the iobp_x calls as those don't exist on ibexpeak
- complete the devicetree with to be disabled PCI devices for the
chip_ops to be called
- Clean up some code copied from bd82x6x
Change-Id: I78d25ffe9af482c77d397a9fdb4f0127e40baddc
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35753
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Tested on Thinkpad X201: PEG device hidden.
Change-Id: Ib378458a55e18cc02fc49b3e6d6939d31dd4aa65
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35744
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This properly sets up the chipset initialization registers, instead of
replaying an RCBA dump.
The information is taken from the EDS and from the thinkpad x201
vendor BIOS disassembly and from an HP UEFI.
TESTED on Thinkpad X201. Seems stable at booting, rebooting and resume
from S3.
Change-Id: I21c2beaf70da27dbe6a56e2612df2c257c05fc62
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35439
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
The extra PCI bus RST# and 200ms delay there was workaround
for custom add-on hardware.
Change-Id: I38c4677cfb41d620498be8e0c257b517995bad5c
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35765
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Change-Id: Ibd5cd2afc8e41cc50abdda0fb7d063073c3acdc1
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35678
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Minimize use of hard-coded value for acpi_table_header->revision to soft
code. Replace with macro defined in arch/acpi.h for FADT and with the
get_acpi_table_revision function for SSDT.
Change-Id: I99e59afc1a87203499d2da6dedaedfa643ca7eac
Signed-off-by: Sourabh Kashyap <Sourabhka@hcl.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35539
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: Ib8a08e9f854b2b0786c69943d6dbb66abe3ad4d8
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33438
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The SPI flash component requirement for Kukui family is 8M so we should
update FMAP for that:
- Add more comments for alignment and size recommendation.
- Enlarge RO to 4M, and RW_SECTION_{A,B} both ~1.5M.
- BOOTBLOCK: 32K->128K, aligned with other ARM boards.
- Preserve RW_DDR_TRAINING for new calibration.
- Reorder the sections for better alignment.
- RW_MISC to contain RW sections that should be merged when creating AU image.
BUG=b:134624821
TEST=Built Kukui image and boots. dump_fmap -h image-kukui.bin:
# name start end size
RW_LEGACY 00700000 00800000 00100000
RW_SHARED 006f7000 00700000 00009000
RW_UNUSED 006f8000 00700000 00008000
SHARED_DATA 006f7000 006f8000 00001000
RW_SECTION_B 00580000 006f7000 00177000
RW_FWID_B 006f6f00 006f7000 00000100
FW_MAIN_B 00582000 006f6f00 00174f00
VBLOCK_B 00580000 00582000 00002000
RW_MISC 00577000 00580000 00009000
RW_ELOG 0057f000 00580000 00001000
RW_DDR_TRAINING 0057d000 0057f000 00002000
RW_NVRAM 0057b000 0057d000 00002000
RW_VPD 00577000 0057b000 00004000
RW_SECTION_A 00400000 00577000 00177000
RW_FWID_A 00576f00 00577000 00000100
FW_MAIN_A 00402000 00576f00 00174f00
VBLOCK_A 00400000 00402000 00002000
WP_RO 00000000 00400000 00400000
RO_VPD 003f8000 00400000 00008000
RO_SECTION 00000000 003f8000 003f8000
RO_FRID 003f7f00 003f8000 00000100
GBB 003f5000 003f7f00 00002f00
COREBOOT 00021000 003f5000 003d4000
FMAP 00020000 00021000 00001000
BOOTBLOCK 00000000 00020000 00020000
Change-Id: Id342d57dc95c6197d05b8a265742a2866c35ae09
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35612
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
ONBOARD_MICRON_MEM and ONBOARD_SAMSUNG_MEM are available.
These are used to determine if Samsung or Micron onboard memory is
assembled. This can not detected run-time.
Choice is replaced by one config.
Only oldest HW revision contains Samsung module, so set
CONFIG_ONBOARD_SAMSUNG memory to default No.
BUG=N/A
TEST=Boot and verified on Facebook FBG-1701
Change-Id: Id65e92bd4b8d4fe3a6b87dec9bf77e3a62e1be96
Signed-off-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35742
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
|
|
No support is available in mainboard.
Add support to mainboard:
- Add mb_log_list[]
- Add routine mb_crtm()
BUG=N/A
TEST=Boot Embedded Linux 4.20 and verify logging on Facebook FBG-1701
Change-Id: I5120ffb6af0b41520056e1773f63b7b2f34a2460
Signed-off-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33464
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lance Zhao <lance.zhao@gmail.com>
|
|
The vendorcode for verified boot is uploaded, but not used by a mainboard.
Add support to the mainboard for verified boot.
The items to be verifed are placed in board_verified_boot.c
BUG=N/A
TEST=Boot Embedded Linux 4.20 and verify logging on Facebook FBG-1701 rev 0-2
Change-Id: I3ea0a95287977df0dea13e05acedd5406538a6ee
Signed-off-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33463
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Reviewed-by: Lance Zhao <lance.zhao@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Previously all boards using eSPI for the Chrome EC just called it
LPC as the code for the chrome EC is the same between the two
busses.
I'm adding a new Kconfig symbol to specify eSPI, so switch the
boards that actually use eSPI to that symbol and add the LPC
symbol to all the others.
The EC_GOOGLE_CHROMEEC_LPC symbol will no longer default
to enabled for x86 platforms, so one symbol or the other needs to be
specified for each platform.
BUG=b:140055300
TEST=Build tested only.
Change-Id: Icf242ca2b7d8b1470feda4e44b47a2cdc20680f2
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35153
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Connected 4K monitor is not configured at max resolution. The
framebuffer size is too small.
Increase the framebuffer size to 64MB. This is sufficient for max
configuration of 1 HDMI monitor combined with internal LCD panel.
BUG=N/A
TEST=4K HDMI monitor and LCD working fine on Facebook FBG-1701
Change-Id: I25d2cd696830fc5bda84ea2b87538f526373998e
Signed-off-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35064
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
|
|
PCB version is determined using inb() in actual code.
Create function mainboard_read_pcb_version to read pcb version.
BUG=N/A
TEST=Boot and verified on Facebook FBG-1701
Change-Id: I7c16627f468d84ca4ad2aab8bf9fb555f50dc23c
Signed-off-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35741
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
BUG: None
TEST: Build successful, checked the CBMEM log if 1f.6 is disabled with this patch
Signed-off-by: Thejaswani Putta <thejaswani.putta@intel.corp-partner.google.com>
Change-Id: I4e74b259ce8f5f70833dce94692dcbe33e8504db
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35509
Reviewed-by: Mathew King <mathewk@chromium.org>
Reviewed-by: Bora Guvendik <bora.guvendik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The previously provided device path made no difference, all
integrated PCI devices point back to the same chip_info
structure.
Change reduces the exposure of various SA_DEVFN_xx and
PCH_DEVFN_xx from (ugly) soc/pci_devs.h.
Change-Id: Ibf13645fdd3ef7fd3d5c8217bb24d7ede045c790
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35656
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Disable memory channel by HW strap pin. Using for factory
debug.
BUG=b:139773082
BRANCH=N/A
TEST=Rework HW strap pin and check /proc/mem_info
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: Ic5f53f0ba3bd432fbcb7513d2a8aa49d42f7a23e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35241
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Two fields of struct sdram_params are renamed for future CL of DRAM full
calibration. Field 'impedance' is also removed.
BUG=none
BRANCH=none
TEST=emerge-kukui coreboot
Change-Id: I2f9673fd5ea2e62ee971f0d81bdd12aaf565e31c
Signed-off-by: Yu-Ping Wu <yupingso@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35738
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Make the the FSP Parameter PchHdaVcType a devicetree setting and make
use of it in the devicetrees of all boards that currently set it.
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Change-Id: Ibafc3b6bd2495658f2bd634218042ec413a89f5e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35542
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Maxim Polyakov <max.senia.poliak@gmail.com>
|
|
A missing definition of gameport base (PNP io 0x60) will cause
an automatic address assignment during PCI/PNP enumeration, which
won't obey limit 0x7ff. This will cause the enumeration to fail
as other devices already have the values enabled.
The symptoms are: not working USB, PS/2, garbled UART console,
not working PCIe GPUs and crashes. Probably because of wrongly
assigned IO ports.
Example of log (shortened):
Done reading resources.
Setting resources...
!! Resource didn't fit !!
aligned base 1000 size 1000 limit 2e7
1fff needs to be <= 2e7 (limit)
PCI: 00:1c.0 1c * [0x0 - 0xfff] io
!! Resource didn't fit !!
aligned base 1000 size 1000 limit 2e7
1fff needs to be <= 2e7 (limit)
PCI: 00:1c.1 1c * [0x1000 - 0x1fff] io
!! Resource didn't fit !!
aligned base 1000 size 1000 limit 2e7
1fff needs to be <= 2e7 (limit)
PCI: 00:1c.2 1c * [0x2000 - 0x2fff] io
!! Resource didn't fit !!
aligned base 400 size 10 limit 2e7
40f needs to be <= 2e7 (limit)
PCI: 00:1f.2 20 * [0x3080 - 0x308f] io
!! Resource didn't fit !!
...
ERROR: PCI: 00:02.0 14 io size: 0x0000000008 not assigned
...
ERROR: PCI: 00:1f.2 10 io size: 0x0000000008 not assigned
ERROR: PCI: 00:1f.2 14 io size: 0x0000000004 not assigned
ERROR: PCI: 00:1f.2 18 io size: 0x0000000008 not assigned
ERROR: PCI: 00:1f.2 1c io size: 0x0000000004 not assigned
ERROR: PCI: 00:1f.2 20 io size: 0x0000000010 not assigned
...
PCI: 00:1b.0 subsystem <- 8086/27d8
PCI: 00:1b.0 cmd <- 102
PCI: 00:1c.0 bridge ctrl <- 0003
PCI: 00:1c.0 subsystem <- 8086/27d0
PCI: 00:1c.0 cmd <- 107
PCI: 00:1c.1 brids70c01mcu0PeC: 0
dV0i8s0immicrocode: upd10a00000y0025 x666600CPU physiaB 0 0 e k
MTRR cheaeu60zeAttemfWaiting for 1st Sot AP: slot 1 apic_L0ecl0zsax a
aInitiNntt kac:oIG0 Ua dUrSGSGL Ct0C07fintel_vga_int15_h
VGA Option ROM wa7..Azalia0Azalia: codkAbCiPCI: 00:1c.0 init finished
We can see the ports probably started to collide after the activation
of 00:1c.0 device. A debug run with compiled SPEW shows the problem
with enumeration:
PCI: 00:1f.1 18 * [0x50b8 - 0x50bf] io
PCI: 00:1f.2 10 * [0x50c0 - 0x50c7] io
PCI: 00:1f.2 18 * [0x50c8 - 0x50cf] io
PCI: 00:1f.1 14 * [0x50d0 - 0x50d3] io
PCI: 00:1f.1 1c * [0x50d4 - 0x50d7] io
PCI: 00:1f.2 14 * [0x50d8 - 0x50db] io
PCI: 00:1f.2 1c * [0x50dc - 0x50df] io
PNP: 002e.7 60 * [0x50e0 - 0x50e0] io <-- gameport base
DOMAIN: 0000 io: base: 50e1 size: 40e1 align: 12 gran: 0 limit: 7ff done
Notice a weird base for DOMAIN, along with the limit.
Adding a definition of gameport (0x220) as a workaround fixes
the problems.
The gameport should be still disabled thanks to disable bits
(W83627THF datasheet is little bit chaotic). I didn't find any info
if the gameport is available on some pads of the motherboard.
Signed-off-by: Petr Cvek <petrcvekcz@gmail.com>
Change-Id: Ie8e42552ac5e638e91e5c290655edcce1f64e408
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35671
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
This is a PCI standard register, no need to alias its
definitions under different names.
Change-Id: Iea6b198dd70fe1e49b5dc0824dba62628dedc69a
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35521
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
This also reworks the interface to override OPs from the devicetree to
match the interface in sb/intel/common/spi.
Change-Id: I534e989279d771ec4c0249af325bc3b30a661145
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/33040
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
* Disable SATA controller and related configs.
* Disable PCIe root ports 10 and related configs.
-> Board uses integrated CnVi for WLAN
* Disable PCIe root ports 12 and related configs.
-> Board uses WWAN intarfaced over USB
Change-Id: If9d49cef290dcccb114afccc3ac34cd072802ea4
Signed-off-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35723
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
drallion uses below LPSS controllers:
I2C: 0/1/4
GSPI: None
UART: 0(Console)
BUG=b:141575294
Change-Id: I9c57f8054f5da5add667168502ebc3e089c440f8
Signed-off-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35638
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Bora Guvendik <bora.guvendik@intel.com>
|
|
To support mt8183 power saving during suspend to RAM, this patch loads
SPM firmware to support SPM suspend. SPM needs its own firmware to do
these power saving in the right timing under correct conditions. After
linux PM suspends, SPM is able to turn off power for the last CPU and do
more power saving for the SoC such as DRAM self-refresh mode and turning
off 26M crystal.
BUG=none
BRANCH=none
TEST=suspend/resume passes for LPDDR4 3200
Change-Id: I3393a772f025b0912a5a25a63a87512454fbc86e
Signed-off-by: Dawei Chien <dawei.chien@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34545
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
|
|
This removes the "ifdef ACPI" which is not needed here as we currently
don't include gpio.h in any asl file.
Change-Id: I803bbee5933eda9423a9bc9fcaea9e905e3ac78e
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35543
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This fixes the warning that power_on_after_fail could not be found,
adds a default config and adds the parameter hyper_threading.
Change-Id: I10b0aa71fa7916b01e93e16cbd81e427fd14f6a4
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35526
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The CONFIG_GBB_HWID can be generated automatically now so we can remove
the test-only HWIDs set in board config files.
BUG=b:140067412
TEST=Built few boards (kukui, cheza, octopus) and checked HWID:
futility gbb -g coreboot.rom
Change-Id: I4070f09d29c5601dff1587fed8c60714eb2558b7
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35635
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I959cdc08d43fea28f8bbc649cd46bab5656d6ca8
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35674
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Enable VBOOT in Kconfig and provide a flashmap that includes all the
needed sections for VBOOT support.
Change-Id: Iee12a5d1781c869b20bc14a52ecbf23474caa3fd
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35594
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Internal pull up need to be enabled for GPD3 as power button pin for
PCH according cometlake pch EDS vol1 section 17-1. Without that pin will
stay floating and hook up XDP can cause system shutdown as power buttone
event will trigger.
BUG=N/A
TEST=Hook up XDP on drallion platform, able to boot up into OS and stay
at power up state.
Change-Id: Idd1befeb14a251b7c0542ca1f99049d07b28fb98
Signed-off-by: Bora Guvendik <bora.guvendik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35666
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
|
|
BUG=b:141734594
Change-Id: I419f7d11dffebe6c44eefa05750834d07d19857b
Signed-off-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35665
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Bora Guvendik <bora.guvendik@intel.com>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
|
|
BUG=b:141575294
Change-Id: I1b2b4362b84b170bd73b760828ca300ec86c4534
Signed-off-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35636
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
|
|
Drallion uses UART 0 for console, change the config accordindly.
BUG=b:139095062
Change-Id: I0ae2f8459b6225b99b758180413afa22386355d4
Signed-off-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35633
Reviewed-by: Bora Guvendik <bora.guvendik@intel.com>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Per google/stout.
Tested with SanDisk SSD U110.
Change-Id: I7cc9837f572236acac2007e95990e64c25a5d6e2
Signed-off-by: James Ye <jye836@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31364
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Alexander Couzens <lynxis@fe80.eu>
|
|
Based on schematic and register dumps.
Change-Id: I91fc47022988cfe986fb8c1ed21dc073ee7d16bc
Signed-off-by: James Ye <jye836@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31365
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Alexander Couzens <lynxis@fe80.eu>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
The vendor id option set here is useless as most SSVID registers get
filled with 0x8086 (their VID) by default, anyway.
Besides that the Kconfig option isn't meant for retrofit ports, cf.
commit 7e1c83e31bd (Add Kconfig options to override Subsystem Vendor and
Device ID). The right place would be the devicetree.
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Change-Id: If67c679bb342f63096902535734106e4f1651118
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35524
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
|
|
Most of the X11 boards with socket LGA1151 are basically the same boards
with just some minor differences like different NICs (1 GbE, 10 GbE),
number of NICs / PCIe ports etc.
There are about 20 boards that can be added, if there is a community for
testing.
To be able to add more x11 boards easily like x11ssm (see CB:35427) this
restructures the x11ssh tree to represent a "X11 LGA1151 series". There
were multiple suggestions for the structure like grouping by series
(x10, x11, x...), grouping by chipset or by cpu family.
It turned out that there are some "X11 series" boards that are
completely different. Grouping by chipset or cpu family suffers from the
same problem. This is why finally we agreed on grouping by series and
socket ("X11 LGA1151 series").
The structure uses the common baseboard scheme, while there is no "real"
baseboard we know of. By checking images, comparing logs etc. we came to
the conclusion that Supermicro does have some base layout which is only
modified a bit for the different boards.
X11SSH-TF was moved to the variants/ folder with it's gpio.h. As we
expect the other boards to have mostly the same device tree, there is a
common devicetree that gets overridden by each variant's overridetree.
Besides that some very minor modifications happened (formatting, fixing
comments, ...) but not much.
Documentation is reworked in CB:35547
Change-Id: I8dc4240ae042760a845e890b923ad40478bb8e29
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35426
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Modify IRQ pin from D21 to A21 and support wake-up from touchpad
BUG=b:141519690
TEST=build bios and verify elan touchpad works fine
Signed-off-by: Peichao Wang <peichao.wang@bitland.corp-partner.google.com>
Change-Id: I6cc5b780ffcee24f1f2a04e88c30628ceb5904e8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35551
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Shelley Chen <shchen@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
new DDR particle:
1. Samung K4A8G165WC-BCWE
2. Hynix H5AN8G6NCJR-XNC
BUG=b:139085024
BRANCH=master
TEST=rework new source to DUT and re-flash bios to DUT and
verify DUT will bring up successfully
Signed-off-by: Peichao Wang <peichao.wang@bitland.corp-partner.google.com>
Change-Id: I0d039af53938086733308a081a77a7398e7bf5d5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35590
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Add the configuration 'Juniper' for the new mainboard.
BUG=b:137517228
TEST=make menuconfig; select 'juniper' and build
Change-Id: I94e3ac7f6de3fecf177e344cb217eaecf6362d69
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35550
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
All variants of hatch are using Comet Lake and so the selection can be
done in Kconfig without requiring each variant to do the same.
Change-Id: Ief34296334ede5ba0f5f13381e92427ccc440707
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35562
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Andrew McRae <amcrae@chromium.org>
Reviewed-by: Edward O'Callaghan <quasisec@chromium.org>
|
|
Sort the names of all variant mainboards in an ascending order.
Change-Id: I19d502298744c0e0cbc91eb836c62ca90cdb9a5c
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35556
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Enable VBOOT in Kconfig and provide a flashmap that includes all the
needed sections for VBOOT support.
Change-Id: I3d58094256d2730dbd249291a8f1ed8df9dfe62d
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35552
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
The implementation of udelay() with LAPIC timers
existed first, as we did not have calculations
implemented for TSC frequency.
Change-Id: If510bcaadee67e3a5792b3fc7389353b672712f9
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34200
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The Razer Blade Stealth H2U is a KabyLake System using:
- Intel KBL 7500U
- ITE8528E SuperIO
- Intel 600P Series NVMe SSD
- Either four MT52L1G32D4PG (16GB) or MT52L512MB32D4PG (8GB)
of soldered memory in dualchannel mode
- (Optional) Touchscreen
- HDMI 2.0a via DP-1: Paradetech PS175
- AlpineRidge Thunderbolt 3 controller
- TPS65982 USB-PD power switch / multiplexer
Even though it has a 16MB chip equipped (W25Q128.V) only the first 8MB
are used and mapped via IFD. The rest is left empty (0xFF). The flash is
not secured in any way and can be read via flashrom. It should be the
source for this port's IFD and ME blobs.
Working:
- USB-A Ports left and right
- Speakers
- Touchscreen (USB)
- Onboard Keyboard in Linux
- NVMe SSD
- SeaBIOS, Tianocore and Grub Payloads
- Webcam
- Powersaving Modes
- Battery state and LID switch, sometimes slow to update.
- Touchpad (I2C-HID)
- Headphones
Not part of this commit:
- Thunderbolt / USB-C (Requires advanced EC signaling)
- Full HDMI support (Currently requires plugged connection at boot)
Change-Id: I7ede881d631e1863f07f5130f84bc3b8ca61a350
Signed-off-by: Johanna Schander <coreboot@mimoja.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34475
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
|
|
Disable root port IOU0 to which built-in NIC is attached.
TEST=on OCP monolake, hide built-in NIC and make sure OS does not report
built-in NIC
Change-Id: I2384e7dd073355f0ced2902ac2d8418996b1c5aa
Signed-off-by: Andrey Petrov <anpetrov@fb.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35322
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: David Hendricks <david.hendricks@gmail.com>
|
|
- configure DMA fw_cfg
- add support to read using fw_cfg_dma
- provide fw config version id info in logs
BUG=N/A
TEST=Build and boot using qemu-i440fx.
Change-Id: I0be5355b124af40aba62c0840790d46ed0fe80a2
Signed-off-by: Himanshu Sahdev <himanshusah@hcl.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35365
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
|
|
This change applies fine-tuned DPTF parameters and TCC offset setting
for kohaku. Also enables EC_ENABLE_MULTIPLE_DPTF_PROFILES for tablet
mode.
BUG=b:137688474
BRANCH=none
TEST=built and verified the setting values
Change-Id: I92e268b2e07ca5a04e29bda84ddb8fc21eb23251
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35532
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Shelley Chen <shchen@google.com>
|
|
Fill the dimm info struct to make SMBIOS type 17 appear.
TESTED=Up Squared
Change-Id: I4de63362c8fea8a886594cdcf0eec48421afb605
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34564
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Drop unused CNF2_LPC_EN, as there is no device which uses IO 0x4e/4f.
Do not use the mainboard model to set COMA_LPC_EN. Make use of
NO_UART_ON_SUPERIO instead, as it is more future-proof.
Change-Id: Iac49250b0f509a42012f82db8aa85ba85559c66f
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35444
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
BUG=b:140545732
TEST=build bios and spd index set to 6, verify DUT bring up normally
Signed-off-by: Peichao Wang <peichao.wang@bitland.corp-partner.google.com>
Change-Id: I337b0bdcd37a9c4baacccbc6786968031a41b31e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35511
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I28a21d64e2781af294670a94c1fc88fb81e80f9e
Signed-off-by: Philipp Deppenwiese <zaolin@das-labor.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35492
Reviewed-by: Andrey Petrov <anpetrov@fb.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
