| Age | Commit message (Collapse) | Author |
|---|
|
For some nissa variants, there are build configurations that need to use
different blobs, but otherwise are identical. Currently, they use the
same choice of board config and configure blob paths appropriately. This
avoids duplication within the Kconfig file, but the resulting firmware
images can be difficult to distinguish, since they report the same
FRID.
Add a prompt string for MAINBOARD_PART_NUMBER so it can be overridden
and round-tripped through make oldconfig, allowing customisation of the
reported FRID and other MAINBOARD_PART_NUMBER-derived values with
minimal overhead.
BUG=b:253966060
BRANCH=None
TEST=CL:3960290 MAINBOARD_PART_NUMBER configs apply successfully
Signed-off-by: Sam McNally <sammc@chromium.org>
Change-Id: I3497d7fa1c04c8fa2592025c771d9dbc65632e6e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68496
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Reka Norman <rekanorman@chromium.org>
|
|
Pentium CPU will use 150W adaptor, this change revises PsysPL2 to 150W
based on fw_config.
BUG=b:253542746
TEST=Check CPU PsysPL2=150W in AP log with Pentium CPU.
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Change-Id: I63b2a9d79454b20b60ba1317a8eebb3c10eff9d6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68665
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
|
|
SaGv is enabled for all brya variants, so it should be harmless
to enable it for brask variants to save some power.
BUG=254374912
TEST=Build and boot to Chrome OS
Signed-off-by: Derek Huang <derekhuang@google.com>
Change-Id: Ib5d1e39b3f901606e2f1449e4ed40d53696562ed
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68646
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
|
|
The touchscreen IRQ has been configured as LEVEL_LOW in skyrim projects.
Therefore, update the gpio.c to be consistent with the configuration.
BUG=b:253506651, b:251367588
BRANCH=None
TEST=FW_NAME=frostflow emerge-skyrim coreboot
Signed-off-by: Frank Wu <frank_wu@compal.corp-partner.google.com>
Change-Id: Iccfe5b01f10899c43151762e4730a05990afa602
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68638
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Chao Gui <chaogui@google.com>
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
|
|
Add a config for FIVR in devicetree for both, mc_ehl1 and mc_ehl2
variants in order to provide the real delay value for the VCC supply
rail. This delay is needed to enable proper switching between different
VCC levels based on current system state.
Change-Id: Ibccb8ea1b42ccd2ff0a37cbd9651528a2a55ebd6
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68666
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Apollo Lake seems to start with PCIe root ports unusable/uninitialized
before FspMemoryInit() is called and FSP-M properly initializes these
root ports.
However, we need the root ports accessible before FspMemoryInit() in
certain cases, such as emitting POST codes through a PCIe device.
For the initialization to happen properly, certain register writes
specified in Apollo Lake IAFW BIOS spec, vol. 2 (#559811), chapter
3.3.1 have to be done.
BUG=none
TEST=Boot on siemens/mc_apl2 with NC_FPGA_POST_CODE enabled and check
that the POST codes are emitted before FspMemoryInit().
Change-Id: If782bfdd5f499dd47c085a0a16b4b15832bc040e
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Signed-off-by: Jan Samek <jan.samek@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68223
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
On nissa, the pre-x86 time is not part of the 1s firmware boot time
target. Including the pre-x86 timestamps causes confusion since the boot
time appears to be greater than 1s, so disable the Kconfig on nissa.
We're not doing any analysis or optimisation of the pre-x86 time on
nissa anyway, this work will start from MTL onwards. Also, the Kconfig
is already disabled on the brya firmware branch, so this will result in
the same behaviour as brya.
Before:
Total Time: 1,205,840
After:
Total Time: 995,300
BUG=b:239769532
TEST=Boot nivviks, check "1st timestamp" is the first timestamp.
Change-Id: I885071c9e0ff9c8fac9444b382567d38a19c3c15
Signed-off-by: Reka Norman <rekanorman@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68553
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: V Sowmya <v.sowmya@intel.com>
Reviewed-by: Kangheui Won <khwon@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Change-Id: I406f21c0c05e6af357e45e718422be94c6fd5408
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68017
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
|
|
Not all kahlee variants use the RT5682 audio codec, so split the
baseboard audio ACPI into two parts and only include the asl for
the codec(s) actually needed for a given variant.
TEST=build/boot aleena, liara variants and verify no ACPI present
for RT5682 codec (which is not present on the boards).
Change-Id: Icb7df4f8e51495ad3cb40113cd00810fd27dcd00
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68583
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Enable DRIVERS_GENESYSLOGIC_GL9755 support for frostflow
BUG=b:253506651, b:251367588
BRANCH=None
TEST=FW_NAME=frostflow emerge-skyrim coreboot
Signed-off-by: Frank Wu <frank_wu@compal.corp-partner.google.com>
Change-Id: I1db598c68687ed17fd9baa3567ab8fdd3e4fb6a8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68483
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Built from a mixture of autoport output, other variants, schematics and
expert guesswork. I don't have this board, but the code has been tested
by someone else and boots successfully (first try) with TianoCore. It's
reasonable to assume most things work, as this board is very similar to
the already-supported variants.
Change-Id: I3d8df483e5573f77782b7d18b1410b391bfe387d
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61541
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Change-Id: I7b279cf2c69f62b47ef497edd372034f148fff03
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68020
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Initialize MT6315 for powering on big cores on MT8186T.
BUG=b:249436110
TEST=build pass.
BRANCH=corsola
Signed-off-by: Sen Chu <sen.chu@mediatek.corp-partner.google.com>
Signed-off-by: Bo-Chen Chen <rex-bc.chen@mediatek.com>
Change-Id: Ib1d71d4f1689ba1e7ea5f798503ef11eff423fff
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68621
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Reviewed-by: Yidi Lin <yidilin@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Change-Id: I9e8ad533e939553a93e76f1dbb37fc98b53f06d6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67970
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Add two new types for MDN DDI descriptor
BUG=b:228284940
TEST=Normal boot and S0i3 cycles
Signed-off-by: Jason Nien <finaljason@gmail.com>
Change-Id: I02793f032f9855dac202a5aca8666c26426d6cb2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66847
Reviewed-by: Bao Zheng <fishbaozi@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Martin Roth <martin.roth@amd.corp-partner.google.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Nikolai Vyssotski <nikolai.vyssotski@amd.corp-partner.google.com>
|
|
Create the gladios variant of the brask reference board by copying
the template files to a new directory named for the variant.
(Auto-Generated by create_coreboot_variant.sh version 4.5.0).
BUG=b:239513596
BRANCH=None
TEST=util/abuild/abuild -p none -t google/brya -x -a
make sure the build includes GOOGLE_gladios
Signed-off-by: Kevin Chiu <kevin.chiu.17802@gmail.com>
Change-Id: I3dc99d97d8e30d9641f56616222dd68e3a0d548d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68569
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Zhuohao Lee <zhuohao@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
We use the name of the APCB file repeatedly, so put it into a variable
so that it's easier to update.
Signed-off-by: Martin Roth <martin.roth@amd.corp-partner.google.com>
Change-Id: I8684db2f7b2d68f0354e37bd8cdfc4f9cab44b8a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67501
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Jason Glenesk <jason.glenesk@amd.corp-partner.google.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
This change is to skip sending the MBP HOB since coreboot doesn't
use it and also helps to reduce the boot time by ~40 ms.
Boot time data
Before:
* 955:returning from FspSiliconInit 1,656,985 (274,416)
After:
* 955:returning from FspSiliconInit 1,593,036 (233,286)
BUG=b:252410202
TEST=Verified that boot time is reduced by ~40 msec.
Signed-off-by: Wonkyu Kim <wonkyu.kim@intel.com>
Change-Id: I0d4f66940529b8d38d9658c769feba8b5c9b715e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68418
Reviewed-by: Tarun Tuli <taruntuli@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
|
|
We need to boot eMMC for modem calibration, there is not need for BIOS
to initialize NVMe anymore as the kernel will do so. Removing the pci
device from the device tree as a first step.
BUG=b:185426670, b:254281839
BRANCH=None
TEST=Boot after removing from the herobrine device tree.
Change-Id: I802dd1361bc56a24ab3d65e6782bc611b7b75ee3
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68571
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
Configure GPIOs based on GPIO_20221014.xlsx of frostflow.
BUG=b:253506651, b:251367588
BRANCH=None
TEST=FW_NAME=frostflow emerge-skyrim coreboot
Signed-off-by: Frank Wu <frank_wu@compal.corp-partner.google.com>
Change-Id: I02272801c85a7c30d24c834a840e026225956fb8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68481
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jon Murphy <jpmurphy@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Add new memory parts in the mem_parts_used.txt and generate the
SPD ID for the parts. The memory parts being added are:
DRAM Part Name ID to assign
MT62F512M32D2DR-031 WT:B 0 (0000)
H9JCNNNBK3MLYR-N6E 0 (0000)
MT62F1G32D4DR-031 WT:B 1 (0001)
H9JCNNNCP3MLYR-N6E 1 (0001)
MT62F2G32D8DR-031 WT:B 2 (0010)
H9JCNNNFA5MLYR-N6E 3 (0011)
BUG=b:250470704, b:247683159
BRANCH=None
TEST=FW_NAME=frostflow emerge-skyrim coreboot
Signed-off-by: Frank Wu <frank_wu@compal.corp-partner.google.com>
Change-Id: I34584092c938539c91d65501ebe34b00212b34d4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68388
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jon Murphy <jpmurphy@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Remove redundant touchscreen "ELAN6915".
BUG=b:254328657
TEST=emerge-nissa coreboot
Signed-off-by: Tyler Wang <tyler.wang@quanta.corp-partner.google.com>
Change-Id: I8f90b071b053858cf720de5ac2a71031fe623d70
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68497
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: David Wu <david_wu@quanta.corp-partner.google.com>
Reviewed-by: Reka Norman <rekanorman@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Craask does not have a SAR proximity sensor.
BUG=b:253387689
TEST=Dump ACPI SSDT and verify SX9324 related entries are not present.
Change-Id: Ia0e3eb6dba82594ca27040d6ab0197da6095f510
Signed-off-by: Victor Ding <victording@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68564
Reviewed-by: Reka Norman <rekanorman@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Test: cbmem reports verb table loaded for codec #2
Change-Id: I4db044535c95ccd3e81a67bb5e58e6f04ee8d12f
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68552
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Test: build/boot google/drallion with non-ChromeOS build, Tianocore
payload. Windows 10, Linux 5.10.x booted successfully
Change-Id: I6358b1d5c71eee065fed96b7bca31e37f30d3a8f
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58405
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Librem Mini has a UART (accessible with soldering), which is very
useful for work on coreboot. It can be used for coreboot/SeaBIOS/Linux
boot logs, or as a general purpose UART.
Change-Id: I38ad5f19da6af5ed286ad3583f34b824a3660916
Signed-off-by: Jonathon Hall <jonathon.hall@puri.sm>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68551
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Configure the Intel iGPU as primary video adapter if enabled according
to EEPROM settings. The default is to use the ASPEED BMC as primary
video adapter, which only has a VGA output and the remote KVM output.
For now, use the FSP GOP driver to light up the iGPU. There are several
issues with libgfxinit on the Hermes, probably due to the unusual setup
of the iGPU's display outputs. They are routed to a mezzanine connector
for a piggy-back sub-board, of which there are two models. The Poseidon
piggy-back has two DisplayPort outputs and an HDMI output coming from a
MegaChips LSPCON. The Avalanche piggy-back routes all three DisplayPort
outputs from the iGPU into a FPGA, which acts as a DisplayPort sink.
Note that the FSP GOP only initializes at most 2 iGPU display outputs.
However, all three outputs function properly once OS (Windows, Linux)
graphics drivers take over.
Additionally, update the config file that Prodrive uses to build
coreboot images so that the iGPU can be used as primary.
TEST=Verify that the iGPU's outputs work properly in pre-OS, Windows and
Linux, on both the Poseidon and Avalanche piggy-backs.
Change-Id: I24d9ebc2055dc246e7f257aa2f3853b22c8af370
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62649
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I1c00322d2b22e1fafffd6ebd66f2df14bcedbd89
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68461
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add VBT data files, ensure secondary VBTs compiled in as needed,
select INTEL_GMA_HAVE_VBT.
TEST=build/boot lindar variant with FSP/GOP display init, edk2 payload
Change-Id: I81022670fabda7994e292d333c999b508e61b469
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68465
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <inforichland@gmail.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Add VBT data files, ensure secondary VBTs compiled in as needed,
select INTEL_GMA_HAVE_VBT.
TEST=build/boot drawcia, mangolor variants with FSP/GOP display
init and edk2 payload
Change-Id: I58a2ed59bd858ce772e92f6659d341036823b11a
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68464
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <inforichland@gmail.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
The ISH build target used for nissa is called adl_ish_lite: CL:3925007,
and by default the binary is installed as
/lib/firmware/intel/adl_ish_lite.bin
We could change the installed name, but it's nicer to keep it consistent
with the build target, so change the name in coreboot instead.
BUG=b:234776154
TEST=Build and boot nirwen, check firmware name is updated in SSDT
Change-Id: I983a38d08e758cf5a12a3f91a601c7e57d42c0cb
Signed-off-by: Reka Norman <rekanorman@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68466
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
1. Set the PL1, PL2 and PL4.
2. Set PsysPL2 and PsysPmax.
BUG=b:253380352 b:253542746
TEST=Compare the measured power from adapter with the value of 'psys'
from the command 'dump_intel_rapl_consumption'.
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Change-Id: I0a7ff64689b39e7754e0aed2f6869881a682fc93
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68437
Reviewed-by: Ren Kuo <ren.kuo@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Maulik Vaghela <maulikvaghela@google.com>
Reviewed-by: Derek Huang <derekhuang@google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
|
|
This change disables unused PCIE RP8 and CLKSRC4. Without this change
storo cannot enter into s0ix properly.
BUG=b:219376808
TEST=Built and verified in storo
Change-Id: I9867825ce53de72ef73920c153002bc3be4dbd2d
Signed-off-by: Zanxi Chen <chenzanxi@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67788
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Xuxin Xiong <xuxinxiong@huaqin.corp-partner.google.com>
Reviewed-by: Jamie Chen <jamie.chen@intel.corp-partner.google.com>
Reviewed-by: Henry Sun <henrysun@google.com>
Reviewed-by: Maulik Vaghela <maulikvaghela@google.com>
Reviewed-by: Aamir Bohra <aamirbohra@google.com>
|
|
Remove the ACPI ALS device from the EC configuration for newer devices,
because some do not have light sensors, and those who do have their ALS
presented through the new EC sensor interface already.
Inspired from commit ("f13e2501525f ("UPSTREAM: mainboard/google/eve: Remove ACPI ALS device")
BUG=b:253967865
BRANCH=none
TEST=Boot a device and ensure that 'acpi-als' device is not present
in /sys/bus/iio/devices.
Change-Id: Ibcfa9e8c5a4679d557150998fd255789d3f8a272
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68493
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Update SoC GPIO setting of camera according to beadrix schematics.
GPP_D13 : NC -> PLTRST (EN_PP2800_CAMERA)
BRANCH=dedede
BUG=b:247178737,b:244120730
TEST=on beadrix, validated by beadrix seconds_system_resume < 500 ms.
Signed-off-by: Teddy Shih <teddyshih@ami.corp-partner.google.com>
Change-Id: Id00cb85cdad900c03842ad69707966aa62410efd
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68129
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Super Ni <super.ni@intel.corp-partner.google.com>
Reviewed-by: Simon Yang <simon1.yang@intel.com>
Reviewed-by: Ivan Chen <yulunchen@google.com>
Reviewed-by: Maulik Vaghela <maulikvaghela@google.com>
|
|
SAR-related Kconfigs are only used by ChromeOS, and should be guarded
properly as such (as most other boards do).
TEST=build glados w/o CONFIG_CHROMEOS, verify SAR-related Kconfigs not
selected.
Change-Id: Id8abf68ed2e9720b5580f7965208dbe36460af07
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68458
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
SAR-related Kconfigs are only used by ChromeOS, and should be guarded
properly as such (as most other boards do).
TEST=build reef w/o CONFIG_CHROMEOS, verify SAR-related Kconfigs not
selected.
Change-Id: I4fe3092e620bcbc33b0411ea69e55154fc118aa4
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68457
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
SAR-related Kconfigs are only used by ChromeOS, and should be guarded
properly as such (as most other boards do).
TEST=build sarien w/o CONFIG_CHROMEOS, verify SAR-related Kconfigs not
selected.
Change-Id: I424033e087bc37c651a922273718fc229b720448
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68456
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add two memory parts and generate the associated DRAM part ID.
1) Hynix H58G66AK6BX070
2) Micron MT62F1G32D2DS-026 WT:B
BUG=b:251363645
TEST=none
Change-Id: Iceb31576533a5b29c5957170473152014fc7e9c8
Signed-off-by: Amanda Huang <amanda_hwang@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68283
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jon Murphy <jpmurphy@google.com>
|
|
When the GSC is ready for the next transaction, it triggers a
GSC_AP_INT_ODL (active low) pulse with 100us duration to notify the AP.
Currently the TPM IRQ is configured as EDGE_RISING. Changing it to
EDGE_FALLING would speed up each register access by 100us. On Kingler,
this saves 20ms for the boot time (0.93s -> 0.91s).
BUG=b:235185547
TEST=emerge-corsola coreboot
TEST=Kingler booted without TPM errors
BRANCH=none
Change-Id: Id282e0f35694bd151781845cbd5aa4b389a30ddc
Signed-off-by: Yu-Ping Wu <yupingso@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68327
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yidi Lin <yidilin@google.com>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
|
|
Allows brya boards to use coreboot-generated FMAP layout
when building for non-ChromeOS target.
TEST=build/boot brya/banshee with edk2 payload, non-ChromeOS build
Change-Id: I21c2247c034d9bdc49f66771a93abad542a1e1fa
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68452
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Allows dedede boards to use coreboot-generated FMAP layout
when building for non-ChromeOS target.
TEST=build/boot dedede with edk2 payload, non-ChromeOS build
Change-Id: Icb975455cde0d75a5af9130ba3e82a4fb0df5613
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68451
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
X9SAE has a PS/2 controller for keyboard and mouse but its definition
in ACPI used to be missing, and X9SAE used to use a generic SuperIO
support initially generated by autoport, so the full NCT6776 support
is added here like x9scl.
Test result:
Log lines like
i8042: PNP: No PS/2 controller found.
i8042: Probing ports directly.
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mousedev: PS/2 mouse device common for all mice
become
i8042: PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at
0x60,0x64 irq 1,12
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mousedev: PS/2 mouse device common for all mice
and more sub-devices within SuperIO is handled by the PNP driver.
Signed-off-by: Bill XIE <persmule@hardenedlinux.org>
Change-Id: Ie5e73e8c3fc4e57c6683d7a7ca70e96c64dd9366
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68446
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Change-Id: If68ce4fef69a2466e76fc7fc504c00ee915e3e36
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68254
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marc Jones <marc@marcjonesconsulting.com>
|
|
ALC5682-VD/ALC5682I-VS load different kernel driver by different hid
name. Update hid name depending on the AUDIO_CODEC_SOURCE field of
fw_config. Define FW_CONFIG bits 41 - 43 (SSFC bits 9 - 11)
for codec selection.
ALC5682-VD: _HID = "10EC5682"
ALC5682I-VS: _HID = "RTL5682"
BUG=b:244620955
TEST=ALC5682-VD/ALC5682I-VS audio codec can work
Signed-off-by: Frank Chu <frank_chu@pegatron.corp-partner.google.com>
Change-Id: Ia6cb56e76bc4e245a32f29b19226fa4fae330c92
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67824
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Shou-Chieh Hsu <shouchieh@google.com>
Reviewed-by: Maulik Vaghela <maulikvaghela@google.com>
|
|
Change-Id: I9b03ccc1100307e3c24393903600d18f6cc9abdc
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68378
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-by: Erik van den Bogaert <ebogaert@eltan.com>
|
|
Enable PMC in devicetree so that resources are allocated properly
for it.
Tested on StarLite Mk III & IV, and both can power on correctly.
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Change-Id: Ib4384b55751a9979e470dd04f6814d4ca170ff34
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67409
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Reset the XHCI controller prior to S5 to avoid XHCI preventing shutdown.
Linux needs to put the XHCI into D3 before shutting down but the
powerstate commands do not perform a reset.
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Change-Id: I3be70443eb85a7dff8055c9de0ca2fd89f4fc88d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67678
Reviewed-by: Tim Wawrzynczak <inforichland@gmail.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This AMD reference board is called Pademelon and not Padmelon, so fix
the name in coreboot. Also update the corresponding documentation.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Id1c7331f5f3c34dc7ec4bc5a1f5fe3d12d503474
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68426
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martin.roth@amd.corp-partner.google.com>
|
|
Add initial fw config as per config.star.
BUG=b:253199788, b:245158908, b:244113761, b:244012065
TEST=emerge-rex coreboot. Make sure that ACPI tables are equivalent
before and after this change with CBI.FW_CONFIG set to 0x1561.
Signed-off-by: Kapil Porwal <kapilporwal@google.com>
Change-Id: I66f8b3e4ab414c03b8d63fdd31e0f3f424619340
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68220
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Tarun Tuli <taruntuli@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
BUG=b:253199788
TEST=Build and boot to Google/Rex.
Change-Id: Ib729c98a4d67aa46992fdccf592010b0313605a6
Signed-off-by: Eran Mitrani <mitrani@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66817
Reviewed-by: Tarun Tuli <taruntuli@google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
When fw_config is unprovisioned, devicetree will disable all probed
devices. However, boot-critical devices such as storage devices need to
be enabled.
As a temporary workaround while adding devicetree support for this,
remove the fw_config probe for storage devices so that all storage
devices are always enabled. On eMMC SKUs, UFS and ISH will be disabled
by the PCI scan anyway. On UFS SKUs, eMMC is not disabled by the PCI
scan, but keeping it enabled should have no functional impact, only a
possible power impact.
BUG=b:251055188
TEST=On yaviks eMMC and UFS SKUs, boot to OS and
`suspend_stress_test -c 10`
Change-Id: I6b3a20f3c14d5e9aa8d71f6ca436b5a682310797
Signed-off-by: Reka Norman <rekanorman@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68365
Reviewed-by: Sam McNally <sammc@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
1.Change the TPM I2C freqeuncy to 1 MHz for xivu.
2.Config same settings as the baseboard for I2C buses 1-5.
BUG=b:249953477
TEST=On xivu, all timing requirements in the spec are met.
Frequencies:
1. I2C0 (TPM): 974.3 Khz
2. I2C1 (TouchScreen); 375.5 Khz
3. I2C3 （Audio): 389.0 Khz
4. I2C5 (Touchpad): 388.5 Khz
Signed-off-by: Ian Feng <ian_feng@compal.corp-partner.google.com>
Change-Id: I33f712c14978b95f3a4da82d6f1f5fbae1283b17
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68071
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Reka Norman <rekanorman@chromium.org>
Reviewed-by: Frank Wu <frank_wu@compal.corp-partner.google.com>
|
|
The PCIe port descriptor list seems to be specific to Merlin Falcon and
Prairie Falcon has a different PCIe root port configuration. Since I
neither have the board nor the different APUs, I just add a comment
about this instead of trying to come up with a PCIe port descriptor list
that may or may not work properly on Prairie Falcon APUs.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I8e1eb67a8f684297bbefc6e2593250d7bd45593f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68407
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martin.roth@amd.corp-partner.google.com>
|
|
Signed-off-by: Maximilian Brune <maximilian.brune@9elements.com>
Change-Id: Ibb7aac1204bc297d16797cac5b32b119d0a9204b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68224
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
1. Add CHROMEOS_WIFI_SAR to include the SAR configs.
2. Add get_wifi_sar_cbfs_file_name() that return the wifi SAR
filename.
BUG=none
TEST=emerge-rex coreboot
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: Ia863eaa53c9456ae0e9f0e8914e0de497a32b53b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68393
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Ivy Jian <ivy.jian@quanta.corp-partner.google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
|
|
Disable the unused PCIe root ports that are disabled in the PCIe port
corresponding descriptor list passed to AGESA/binaryPI. This descriptor
list is in src/mainboard/google/kahlee/variants/baseboard/OemCustomize.c
and it only has B0D2F2 (gpp_bridge_1) and B0D2F4 (gpp_bridge_3) enabled.
Since the PCIe engines marked as unused in the port descriptor list
won't show up as PCI devices, don't enable those PCI devices in the
devicetree so that coreboot won't complain about static PCI devices not
being found on the PCI bus.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: If8378e343a2eb13de66171cf4f38d77ae3401016
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68382
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
|
|
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I63b1053d36b284ed95b015c0b4b26bdf8e162e67
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68381
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I509daac75c80bdca808706f783b04843209cc313
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68380
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The board's PCIe port descriptors have the PCIe engine disabled, so
update the devicetree accordingly.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ic97a54c3cc762a36752d6b9f21467428912a9edd
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68379
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I9a429c0fd23eb3b52a19a974b22079d675e3506a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68318
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Since commit 60e9114c6210 ("include/device: ensure valid link/bus is
passed to mp_cpu_bus_init"), no dummy LAPIC device is required under the
CPU cluster device. Since the CPU cluster device is already present in
the Stoneyridge chipset devicetree, drop the whole CPU cluster part from
the mainboard's devicetrees.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I8918c14be25ac9756926a9c6a2806a3dceced42a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68317
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
When using a Merlin Falcon APU, explicitly enable the PCIe root port at
B0D3F1. B0D3F0 is only a dummy PCI device function, but needs to also be
enabled in order for the actually used function to be usable. Prairie
Falcon doesn't have and PCI device 3 on bus 0, so remove D3F0 from the
common mainboard devicetree.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I01f9b9ac2a9ebd5899a093d97eb5b2d76d309f66
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68315
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Enable the correct PCIe root ports in the devicetree so that the
configuration matches the PCIe port descriptors in
src/mainboard/amd/padmelon/bootblock/OemCustomize.c.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Idb00a65adcf2059d7432a8df08654bb0ba965e24
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68314
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
PCI devices that aren't present in the devicetree will be treated as
enabled. Since the chipset devicetree that will be added in a follow-up
patch disables this device by default, explicitly enable the IOMMU
device on the Stoneyridge mainboards that don't disable it to keep the
same behavior.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I4a2cdd00abe8309244829dc633dd8a9ca0038dfa
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68313
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Since the devicetree files are passed to util/sconfig without being
processed by the C preprocessor, using #if in the devicetree won't give
the behavior that might be expected. Instead sconfig treats the #if as a
comment, but still processes all other lines. To get the intended
behavior, replace the C preprocessor usage in the devicetree by moving
the APU-specific parts to override devicetrees that get selected
according to the selected APU type.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Iddd317b27a838849fa40c0fb77d942609104cf04
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68312
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
PCIEXP_HOTPLUG_PREFETCH_MEM_BELOW_4G is no longer needed so remove it.
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Change-Id: I82841c2114ceb5e7a46ce228fce63d24822098d2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68084
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Change-Id: I80f3d2c90c58daa62651f6fd635c043b1ce38b84
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68255
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Switch from gpio_configure_pads() to gpio_configure_pads_with_override()
so variants can override romstage GPIO defaults. Rename baseboard
function and add an weak empty override function to be used by variants.
Will be used for touchscreen power sequencing in a follow-on commit.
Change-Id: I45586237919cd07a171beac57f3510e26338f67f
Signed-off-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67811
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
Create the zombie variant of the herobrine reference board by
copying the template files to a new directory named for the variant.
(Auto-Generated by create_coreboot_variant.sh version 4.5.0).
BUG=b:249180463
BRANCH=None
TEST=util/abuild/abuild -p none -t google/herobrine -x -a
make sure the build includes GOOGLE_ZOMBIE
Signed-off-by: Maulik Vaghela <maulikvaghela@google.com>
Change-Id: Ifecf0a6323b20012defbf14bd16ce2f1f41f4714
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68303
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Bob Moragues <moragues@google.com>
Reviewed-by: Shelley Chen <shchen@google.com>
|
|
This change updates scl_lcnt, scl_hcnt, sda_hold value for I2C5.
BUG=b:249031186
BRANCH=brya
TEST=TP function is normal from EE check.
Signed-off-by: John Su <john_su@compal.corp-partner.google.com>
Change-Id: I5e756b7d7e14cace24ef2dfbb323c840c867ae1a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68329
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Frank Wu <frank_wu@compal.corp-partner.google.com>
|
|
HP Z220 series has PCI slot(s) but Interrupt Routing Table in ACPI
used to be missing, so one is added.
Note that the values within the added one are obtained from my own SFF
variant. If other variants have different values, please add them in a
manner similar to mb/gigabyte/ga-b75m-d3h/acpi/pci.asl.
Test result:
Log lines like
pci 0000:00:1e.0: can't derive routing for PCI INT A
ath9k 0000:04:00.0: PCI INT A: no GSI
disappeared from dmesg.
Signed-off-by: Bill XIE <persmule@hardenedlinux.org>
Change-Id: I8522b25ac46db2054302c8f2418927c722b157e0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68334
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Signed-off-by: Bill XIE <persmule@hardenedlinux.org>
Change-Id: I66f99a5afbdd2b847a916a470a5def9a6d3999bc
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68335
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Strings in C are highly cursed. Use `snprintf()` to minimize the
potential of running into undefined behavior in the future.
Change-Id: I3caef25bc7676ac84bb1c40efe6d16f50f8f4d26
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68323
Reviewed-by: Patrick Georgi <patrick@coreboot.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
|
|
The `eeprom_read_serial()` function could return a non-NULL terminated
string if the serial in EEPROM has `HERMES_SN_PN_LENGTH` (32) non-NULL
characters. Make this impossible by adding an additional character for
a NULL byte in the static buffer, which always gets set to 0 (NULL).
Change-Id: I306fe1b6dd3836156afca786e352d2a7dca0d77c
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68322
Reviewed-by: Patrick Georgi <patrick@coreboot.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
|
|
Configure PMC mux in devicetree.
Tested on StarBook Mk V with Ubuntu 22.04.
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Change-Id: I297d5446e43357d97357f345668cf40dcd28502d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68083
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
|
|
Enable the P2SB so that the SPI is discoverable by the OS.
Change-Id: I49802f93a97a18ecc10f48d213619855728e1290
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67029
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: Ie9655406c7afe7a22f131d35633a697c5bbde4e3
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67027
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Fixes brightness controls on Windows 10.
Change-Id: I33ac1b5a17c95dbb1b166c38fcd639cdac439724
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67636
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jeremy Soller <jeremy@system76.com>
|
|
Windows hardware tests require this field not be "Reserved".
The System76 EC firmware does not report the wake type, so it is not
possible to know if the system was powered on from the power switch or
Wake-on-LAN. In the case WoL is used, this will report the wrong value.
Change-Id: I4653c6bce2a5f0a88281fc810df5646e44f90674
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66837
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jeremy Soller <jeremy@system76.com>
|
|
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Change-Id: I2da15db3d7fba4396c74800e531476c108cafe17
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67421
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Enable SRAM in devicetree so that resources are allocated properly
for it.
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Change-Id: I1d7ee4f950b31f2be6fb7bd107b5fe54785ed81a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67420
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Enable the P2SB so that the SPI is discoverable by the OS.
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Change-Id: Ied7a6ea706e6da86182c109ab4813fa3fcebb1f8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67419
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
BRANCH=none
BUG=b:234776154
TEST=build and boot Nirwen UFS, copy ISH firmware to host
file system /lib/firmware/intel/adln_ish.bin
check "dmesg |grep ish", it should show:
ish-loader: ISH firmware intel/adlnrvp_ish.bin loaded
Signed-off-by: Meera Ravindranath <meera.ravindranath@intel.com>
Change-Id: I89782b0b7dde1fca0130472a38628e72dfd5c26c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68164
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Reka Norman <rekanorman@chromium.org>
|
|
First of all, make sure that `get_board_settings()` never returns NULL.
If there's a problem, return predefined values for board settings.
If the board settings definition differs between coreboot and the BMC,
the CRC will not match. Allow coreboot to use the BMC settings provided
by older BMC firmware revisions which have less settings, if the CRC of
the first N bytes matches the expected CRC.
TEST=Boot coreboot master with BMC FW R04.05, observe board settings
being honored even though coreboot's definition has an extra option.
Change-Id: I0f009b21ef0850a2af6edef1818c770171358314
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67381
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch enables PD Sync for Rex.
BUG=b:248775521
TEST=Able to boot Google/Rex with PD sync enabled.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I749b5dea481c7546579e97f923f143dd17f831d3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67819
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Ivy Jian <ivy.jian@quanta.corp-partner.google.com>
|
|
Add a new zydron variant, which is a variant of brya's skolas
baseboard. currently copy the variant file from kano.
BUG=b:250787251
TEST=build pass
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Change-Id: I49a41678568daef80b7cd1e3ed60ce4763034f9e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68130
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: YH Lin <yueherngl@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
birman is the reference board for the morgana SoC. It needs to be
updated to match the actual board design as well.
Signed-off-by: Martin Roth <martin.roth@amd.corp-partner.google.com>
Change-Id: I4b16854c954949217a76c3d4f04ddc4001f64337
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68196
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Create the frostflow variant of the skyrim reference board by
copying the template files to a new directory named for the variant.
(Auto-Generated by create_coreboot_variant.sh version 4.5.0).
BUG=b:240970782
BRANCH=None
TEST=util/abuild/abuild -p none -t google/skyrim -x -a
make sure the build includes GOOGLE_FROSTFLOW
Signed-off-by: Chao Gui <chaogui@google.com>
Change-Id: I937e6562094968824e73bfa20390b3ec8b24dfa0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68189
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Frank Wu <frank_wu@compal.corp-partner.google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Write the value for reset cause registers to the EEPROM for debugging.
Change-Id: I827f38731fd868aac72103957e01aac8263f1cd3
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67483
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Adjust the EEPROM layout to account for two new fields: board part
number and product part number. In addition, put them in a Type 11
SMBIOS table (OEM Strings). Also, rename a macro to better reflect
its purpose.
Change-Id: I26c17ab37859c3306fe72c3f0cdc1d3787b48157
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67759
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Enable DRIVERS_GENESYSLOGIC_GL9750 for lisbon
BUG=b:246657849
TEST=FW_NAME=lisbon emerge-brask coreboot
Signed-off-by: Kevin Chiu <kevin.chiu.17802@gmail.com>
Change-Id: I74cd634700b2de16ae471e0a738b67a14fd82a50
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68168
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add the `eeprom_read_serial()` function to read serials from the EEPROM.
Note that there's only one buffer now: this means only one serial can be
accessed at the same time, and the buffer needs to be cleared so that it
does not contain old data from other serials. Given that the serials are
copied one at a time into SMBIOS tables, having one shared buffer is not
a problem.
Change-Id: I5c9781e4e599043be756514cfd6dd86dedcf580c
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67275
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The PCH's SGPIO pads are connected to a buffer chip that is powered from
the always-on +3V3_AUX rail. For some cursed reason, when the SGPIO pads
stay configured as SGPIO when a Poseidon system shuts down, voltage from
the +3V3_AUX-powered buffer chip will leak into the +5V rail through the
SATA backplane. Just pulling the SGPIO pads low before the system powers
off stops the +5V rail from being cross-powered.
This issue has only been observed in S5, but it's very likely other
sleep states are affected as well. Thus, always pull the SGPIO pins
low before entering ACPI S3 or deeper because the power supply will
turn off in these states as well.
TEST=Obtain a Poseidon system, verify that the +5V rail is cross-powered
after going to S5. We measured 0.17V on our system, but voltages as
high as 0.6V were measured on other systems. Verify that unplugging
the SGPIO cable going to the SATA backplane results in the +5V rail
voltage dropping to 0V, which indicates that the voltage leakage is
exclusively coming from the SGPIO and SATA backplane. Finally, make
sure that the +5V rail voltage drops to 0V after going into ACPI S5
with this patch applied and the SGPIO cable connected.
Change-Id: Ic872903d5fcdd1c17e02b4c06d5ba29889fbc27d
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66616
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
|
|
The intention of predefining driver strength is to avoid that the OS
SD-Card driver changes this setting.
Change-Id: I02fdac94462da1cd77f8dc972faf16f28d94c946
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68166
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
Change the TPM I2C freqeuncy to 1 MHz for pujjo.
BUG=b:249953707
TEST=On pujjo, all timing requirements in the spec are met.
Frequencies:
pujjo - 987.80 kHz
Signed-off-by: Leo Chou <leo.chou@lcfc.corp-partner.google.com>
Change-Id: If99b5022a9b67e9c63c440a1e398d56bb2c467e2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68098
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Reka Norman <rekanorman@chromium.org>
|
|
Update parameters for all I2C devices.
After applied this patch, the measured the I2C frequency meets spec
BUG=b:249953708
TEST=FW_NAME=yaviks emerge-nissa coreboot
flash and measure the all I2C devices
1. I2C0 (TPM): 980.6 Khz
2. I2C1 (TouchScreen); 392.6 Khz
3. I2C3 （Audio): 394.9 Khz
4. I2C5 (Touchpad): 391.6 Khz
Signed-off-by: Wisley Chen <wisley.chen@quanta.corp-partner.google.com>
Change-Id: I33c2891f17bc3c572bbfcbf30bbbdef9eb850ce7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68082
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Reka Norman <rekanorman@chromium.org>
|
|
Add configuration to bump up the SPI flash bus speed from 66 MHz to 100
MHz starting the board version where required schematics update is done.
BUG=b:245949155
TEST=Build and boot to OS in Skyrim with 100 MHz SPI bus speed. Perform
warm and cold reboot cycles for 100 iterations each. Observe that the
boot time improved by ~115 ms compared to 66 MHz SPI flash bus speed.
At 66 MHz:
508:finished loading body 538,319 (83,806)
11:start of bootblock 1,196,809 (624,777)
14:finished loading romstage 1,236,905 (39,163)
970:loading FSP-M 1,237,056 (37)
15:starting LZMA decompress (ignore for x86) 1,237,073 (17)
16:finished LZMA decompress (ignore for x86) 1,358,937 (121,864)
8:starting to load ramstage 2,010,304 (0)
15:starting LZMA decompress (ignore for x86) 2,010,312 (8)
16:finished LZMA decompress (ignore for x86) 2,067,181 (56,869)
971:loading FSP-S 2,078,232 (7,999)
17:starting LZ4 decompress (ignore for x86) 2,078,253 (21)
18:finished LZ4 decompress (ignore for x86) 2,084,297 (6,044)
90:starting to load payload 2,316,933 (5)
15:starting LZMA decompress (ignore for x86) 2,316,947 (14)
16:finished LZMA decompress (ignore for x86) 2,339,819 (22,872)
Total Time: 2,464,338
At 100 MHz:
508:finished loading body 515,118 (59,364)
11:start of bootblock 1,115,043 (566,110)
14:finished loading romstage 1,146,713 (29,697)
970:loading FSP-M 1,146,865 (38)
15:starting LZMA decompress (ignore for x86) 1,146,881 (16)
16:finished LZMA decompress (ignore for x86) 1,249,351 (102,470)
8:starting to load ramstage 1,900,568 (1)
15:starting LZMA decompress (ignore for x86) 1,900,576 (8)
16:finished LZMA decompress (ignore for x86) 1,956,337 (55,761)
971:loading FSP-S 1,967,357 (7,930)
17:starting LZ4 decompress (ignore for x86) 1,967,377 (20)
18:finished LZ4 decompress (ignore for x86) 1,972,925 (5,548)
90:starting to load payload 2,205,300 (6)
15:starting LZMA decompress (ignore for x86) 2,205,313 (13)
16:finished LZMA decompress (ignore for x86) 2,227,087 (21,774)
Total Time: 2,349,804
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Change-Id: I5e8db22151fbc2db1f9e81b3644338348160736d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68116
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jon Murphy <jpmurphy@google.com>
|
|
use function to check if pci device is on a particular bus
number.
TEST: compiled and qemu run successfully
Signed-off-by: Fabio Aiuto <fabioaiuto83@gmail.com>
Change-Id: I4a3e96381c29056de71953ea2c39cd540f3df191
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68103
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This change updates scl_lcnt, scl_hcnt, sda_hold value for I2C5 to
follow I2C specification.
I2C_TCHPAD_SCL high period time is from 0.53 us to 0.6952 us.
I2C_TCHPAD_SDA hold time is from 0.13 us to 0.4623 us.
BUG=b:249031186
BRANCH=brya
TEST=EE check OK with test FW and TP function is normal.
Signed-off-by: John Su <john_su@compal.corp-partner.google.com>
Change-Id: I5977f0dbba8924cc8a1c72c36358d6ba6f2de940
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67920
Reviewed-by: Ricky Chang <rickytlchang@google.com>
Reviewed-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Frank Wu <frank_wu@compal.corp-partner.google.com>
|
