| Age | Commit message (Collapse) | Author |
|---|
|
Add devicetree and Kconfig entries to enable additional configuration
of the Pericom PI7C9X2G608GP PCIe switch on this board variant.
The amplitude is being adjusted to 425 mV and de-emphasis level to
6.0 mV.
BUG=none
TEST=Read out the PCIe config space values of the switch and check if
they match with the ones configured over SMBus.
Change-Id: I11459f0794278ad614aa6e16c56df1ad578fe2f8
Signed-off-by: Jan Samek <jan.samek@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74434
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
To improve the rate of data transfer for PCIe root port #2 (00:1c.1) and
root port #3 (00:1c.2) set the max payload size to 256 bytes for both
root ports.
Change-Id: I553f6cf090d799fbbaafb925646c6566d6951a86
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75127
Reviewed-by: Jan Samek <jan.samek@siemens.com>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
|
|
This mainboard contains in addition to its base variant, mc_ehl2, an LCD
panel driven through the PTN3460 eDP-to-LVDS bridge.
This patch enables the PTN3460 support by adding the device to
devicetree.cb and board-specific configuration parameters in
lcd_panel.c.
BUG=none
TEST=Boot with the LCD panel attached and observe whether the picture is
stable and free of artifacts coming from wrong resolution and timing.
Change-Id: I196d7ceeb7ac241c9b95db2ef791a5f3ff7890a7
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74936
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jan Samek <jan.samek@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
This mainboard is based on mc_ehl2. In a first step, it contains a copy
of mc_ehl2 directory with minimum changes. Special adaptations for
mc_ehl5 mainboard will follow in separate commits.
Change-Id: Id80f8eb49dd2fed0ed1ffc479d47d8669eca84c9
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74935
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
With the introduction of a new Linux version a problem has appeared
after a software initiated reset via CF9h register. The problem
manifests itself in the fact that the Linux kernel does not start after
the reboot. The problem is solved by setting bit 3 to 1 in Reset Control
Register (I/O port CF9h). This leads to the fact that the PCH will drive
SLP_S3 active low in the reset sequence. It leads to the same behavior
as in commit 04ea73ee78bc ("siemens/mc_apl3: Set Full Reset Bit into
Reset Control Register") explained.
Change-Id: Ia8b7f997ca6234add569da751e1070144790e258
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75041
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jan Samek <jan.samek@siemens.com>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
Change-Id: I6578aee52e6900b25441dc119383856acc480231
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75042
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jan Samek <jan.samek@siemens.com>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
An underscore has crept into the mainboard model option for mc_ehl3 and
mc_ehl4 by mistake. This patch fixes the incorrect entry.
Change-Id: Ie59619877fb6341a5bbfe91c13e7692943480ad0
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75040
Reviewed-by: Jan Samek <jan.samek@siemens.com>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
There are only SSD connected to SATA ports on this mainboard. To prevent
misbehavior, set the correct hard drive type for enabled SATA ports.
BUG=none
TEST=Boot into OS and check the stability of the SSD
Change-Id: I116b1e36f0582956604c3c2508961ffb3de0898a
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74947
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jan Samek <jan.samek@siemens.com>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
Since commit 833bb448c521 ("mb/siemens/mc_ehl: Remove spd.bin from
CBFS"), the subdir 'spd' is no longer necessary.
Change-Id: Ibaf44e3181b2167aa83cffcc59835196e4cb5cdb
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74780
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jan Samek <jan.samek@siemens.com>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
The support for a spd.bin from CBFS was removed for all mc_ehl boards in
commit 833bb448c5213 (mb/siemens/mc_ehl: Remove spd.bin from CBFS).
There is still a remaining comment in romstage_fsp_params.c referring to
the removed capability. This fix removes the spd.bin related part of the
comment to stay consistent with the code.
Change-Id: I669ee1c33d1d1c47764640982f71129195e63f14
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74801
Reviewed-by: Jan Samek <jan.samek@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
|
|
This mainboard has SD slot available and therefore it should be enabled.
Use the same SD card configuration as for mc_ehl2 mainboard.
Change-Id: Icd9b25301311679cf93b05ba83a24e551261a020
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74653
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
This mainboard has the RTC RV-3028-C7 connected to the I2C1.
TEST:
- Console Log shows no errors for RV-3028-C7 during I2C1 init
- Finalize device for I2C 00:52 shows correct date and time
Change-Id: I1b4115d7844a0c218fdf92cb1af2da5a95eb4337
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74652
Reviewed-by: Jan Samek <jan.samek@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Correct the USB settings, suitable for this mainboard.
Change-Id: I943eb891e2f2d967acfd441c085063dbad49e993
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74651
Reviewed-by: Jan Samek <jan.samek@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Since mc_ehl4 was only a copy of mc_ehl1 in a first step, the default
value of the Kconfig switch EARLY_PCI_BRIDGE_FUNCTION must be set to
'0'. On this mainboard NC FPGA is connected to PCIe root port #1
(00:1c.0).
Change-Id: I15035523d8575d486c3f2d0ffe3916712ee89d7d
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74650
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
Since mc_ehl4 was only a copy of mc_ehl1 in a first step, the GPIOs must
be adjust according to the circuit diagram for this mainboard.
Change-Id: I66bfbb380e9a05b3a2c08d5d1980e9749b46ee43
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74628
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
With the latest hardware revision, the two GPIOs GPD11 and GPP_C8 are no
longer used.
BUG=none
TEST=Checked output verbose GPIO debug messages
Change-Id: Ia06f93aee4eccb0e4230f0c3ef53922d42701f21
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74201
Reviewed-by: Jan Samek <jan.samek@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
The default SPD size is set to 256 bytes, instead of 512 for
LPDDR4/DDR4 if not overridden by the mainboard Kconfig. This caused
the SMBus libraries to read only the lower half of the DIMM SPD on
protectli/vault_ehl. The lower half of the SPD passed to FSP causes
a bug in DIMM change detection, which relies on the CRC of the
manufacturer bytes in the upper half of the SPD (CRC of zero bytes
always gives zero so no change was assumed). Setting the DIMM SPD size
to 512 fixes it.
Setting the SPD size in SoC will also avoid such problems in the future
Elkhart Lake ports. Elkhart Lake supports only LPDDR4/DDR4 so providing
the correct default of 512 bytes is an obvious thing to do.
TEST=Boot Protectli VP2420 (vault_ehl) with different DIMMs and see
FSP is retraining the memory instead of doing the fastboot with old
DIMM data.
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Change-Id: I998ed8781951034419cadc26c04ff1e0a124b267
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73933
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Due to a non-optimal RX signal (receive) on PCIe root port #4 (00:1c.3)
and #5 (00:1c.4), the speed must be limit to Gen 1.
BUG=none
TEST=RX signal measured with oscilloscope
Change-Id: I695c0ef961290676fe421b6efd631d6e94d6d556
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73767
Reviewed-by: Jan Samek <jan.samek@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Reviewed-by: Maximilian Brune <maximilian.brune@9elements.com>
|
|
Correct the remaining PCI devices, differing from the ehl1 mainboard.
Change-Id: Ie09188b72a62c4d5cba2fcda6f60f3bc0098633e
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73765
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jan Samek <jan.samek@siemens.com>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Reviewed-by: Maximilian Brune <maximilian.brune@9elements.com>
|
|
As discused earlier, the callback name 'mb_adjust_cfg' was considered
too generic. The new naming is chosen to be consistent with other
drivers' callback names designed to be used at mainboard level.
Also other functions, namely 'mb_get_edid' and 'mb_select_edid_table'
are renamed accordingly.
BUG=none
TEST=Builds for siemens/mc_apl{1,4,5,7} and siemens/mc_ehl boards
complete successfully.
Change-Id: I4cbec0e72e5f03e94df0faa36765d1a6cd873a7a
Signed-off-by: Jan Samek <jan.samek@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/72629
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
There were two wrong comments in all mc_ehl gpio.c files. This patch
corrects the incorrect comments.
Change-Id: Iea356db177227d89b91be32a4e2367c612b77350
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/72458
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This mainboard does not use security features like TPM.
Change-Id: Ieebbf12fc844573ffadb089da78062dd2033517a
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/72429
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
The upcoming mc_ehl4 variant is the first Siemens Elkhart Lake mainboard
without a TPM. For this reason, the corresponding Kconfig switches must
be moved to variant level. To prevent Jenkins build from complaining,
the TPM is removed in the following patch.
Change-Id: Ic73ccd1b52e57c1cf1dd7337b0e28beaadbece8e
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/72428
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
Measurements have shown that the automatic calibrated values for RGMII
output impedances are too low. For this reason, set the PMOS value to 16
and the NMOS to 13.
Change-Id: Ic3382889d3281faccb03819f9680a9763703b2a1
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73019
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This mainboard is based on mc_ehl1. In a first step, it contains a copy
of mc_ehl1 directory with minimum changes. Special adaptations for
mc_ehl4 mainboard will follow in separate commits.
Change-Id: I3c1f2cf4a3dcae58895f6d14a7fce46b2825e6ba
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/72427
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
With the latest hardware revision, the two GPIOs GPP_B15 and GPP_E19 are
no longer connected to a native function.
BUG=none
TEST=Checked output verbose GPIO debug messages
Change-Id: I266612f041b749aa83b366497b4211fc075c7bd7
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73341
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jan Samek <jan.samek@siemens.com>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
The currently used panel type could work with 500 ms but increasing
the value to 1 second allows to use a wider range of LVDS LCD panels,
as many of them specify the delay of 1 s as minimum.
BUG=none
TEST=Test link stability using a panel with minimum re-power delay of
1 s.
Change-Id: I2dd86e791c1212b67a80d7e6cfc474ad91b26c6b
Signed-off-by: Jan Samek <jan.samek@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/72804
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
Change-Id: I7eaf625e5acfcefdae7c81e186de36b42c06ee67
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/72704
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Reviewed-by: Sean Rhodes <sean@starlabs.systems>
|
|
Contents of the EDID are passed by a reference to an array
of length 0x80, for which the macro 'PTN_EDID_LEN' has already
been around.
This patch makes use of this macro within the driver and mainboard
implementation utilizing it.
BUG=none
TEST=A successful build of mc_apl{1,4,5,7} and mc_ehl3 mainboards.
Change-Id: If7d254aaf45d717133bb426bd08f8f9fe5c05962
Signed-off-by: Jan Samek <jan.samek@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/72653
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
|
|
Change-Id: Id8e1a52279e6a606441eefe30e24bcd44e006aad
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69815
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Jonathon Hall <jonathon.hall@puri.sm>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jakub Czapiga <jacz@semihalf.com>
|
|
Since the PSE GBE0 MAC has been disabled on this board in
commit 343644006f89 ("mb/siemens/mc_ehl3/devicetree.cb:
Remove TSN GbE 0"), therefore disable the corresponding
GPIOs as well.
BUG=none
TEST=Test link detection and IP assignment on the remaining
ports (PSE GBE1 and PCH GBE0) of mc_ehl3.
Change-Id: Ifa055f58894688471d68b9b93fcb994fdcb2a568
Signed-off-by: Jan Samek <jan.samek@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/72449
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The parallel mp code picks up lapics at runtime, so remove it from all
devicetrees that use this codebase.
Change-Id: I5258a769c0f0ee4bbc4facc19737eed187b68c73
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69303
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Return generic coreboot error codes from the mb_adjust_cfg
callback used in mainboards instead of '-1' constant and
a driver-specific success-indicating define.
BUG=none
TEST=Boards siemens/mc_apl{1,4,5,7} and siemens/mc_ehl3
build correctly.
Change-Id: I5e0d4e67703db518ed239a845f43047f569b94ec
Signed-off-by: Jan Samek <jan.samek@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/72071
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
Enable early POST code display on this variant using
the common mc_apl1 baseboard functionality.
BUG=none
TEST=Boot on mc_apl5 and observe that POST codes are
displayed before DRAM training.
Change-Id: I390e0ab09ca830637e7a991db77e994d6c358e75
Signed-off-by: Jan Samek <jan.samek@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/72386
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Enable early POST code display on this variant using
the common mc_apl1 baseboard functionality.
BUG=none
TEST=Boot on mc_apl6 and observe that POST codes are
displayed before DRAM training.
Change-Id: I2a52c241c383f8ebcf05052e9bc0ba13e63e3728
Signed-off-by: Jan Samek <jan.samek@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/72116
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
Move logic previously used only in the mc_apl2 variant to
the mainboard level so that other variants can also make
use of it without code duplication.
This functionality on the mc_apl6 variant will be enabled
in a follow-up patch.
BUG=none
TEST=Boot on siemens/mc_apl2 and observe that the POST
codes are displayed before DRAM training.
Change-Id: I762e328ad06c047d911ce1fc40f12a66cbd14e11
Signed-off-by: Jan Samek <jan.samek@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/72115
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
With the addition of the mc_ehl3 board variant, a few
points about commenting the code arose either from the
review or during the implementation itself.
This patch unifies structure of these files, which
have a similar structure across more Siemens boards
utilizing the PTN3460 eDP-to-LVDS bridge.
BUG=none
TEST=Check that images for the affected boards can be
built.
Change-Id: I59820362e1f87e296c5548b9c3cecba4d2710fe7
Signed-off-by: Jan Samek <jan.samek@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/72068
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This board contains in addition to its base variant, mc_ehl2,
an LCD panel driven through the PTN3460 eDP-to-LVDS bridge.
This patch enables the PTN3460 support by adding the device to
devicetree.cb and board-specific configuration parameters in
lcd_panel.c, based upon a similar implementation in siemens/mc_apl7.
BUG=none
TEST=Boot with the LCD panel attached and observe whether
the picture is stable and free of artifacts coming from wrong
resolution, timing etc.
Change-Id: Ib8a1a6f47053406e42554c2dd33684165d54be08
Signed-off-by: Jan Samek <jan.samek@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/70692
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
The {read,write}{16,32}() functions used in this file come from the
mmio.h header, so include it directly.
BUG=none
TEST=Read out the SD card controller (device 1a.1) PCI registers
in Linux and check whether the values reflect the ones defined
in this file.
Change-Id: Iff7b55ef2bf98371b7d7d9114ccf3ebed64772a2
Signed-off-by: Jan Samek <jan.samek@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/72009
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
Change MAINBOARD_PART_NUMBER Kconfig value for mc_ehl3
from "MC_EHL3" to "MC EHL3".
Change-Id: Ie548607c5fb62faaed4921af714bc9b912e558a8
Signed-off-by: Jan Samek <jan.samek@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/71775
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
<gpio.h> chain-include <soc/gpio.h>.
Change-Id: Ia57d5cd33c70b6a755babd4db56c64c0e3666f9f
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/71817
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Enable the real-time tuning to improve performance in the real-time
environment for this mainboard.
Change-Id: I91ad7ca58add92b5cc66148aff8378890ee217eb
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/71234
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Due to mainboard restrictions a SATA link at Gen 3 (6 Gbps) can cause
issues as the margin is not big enough. Limit SATA speed to Gen 2 to
achieve a more robust SATA connection.
Change-Id: Ia79998db5f959528a4e8e29e570a7f55283adee1
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/71230
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Due to a high I2C bus load on the mainboard I2C frequency of 400 kHz
leads to poor signaling. Therefore limit the I2C speed to 100 kHz for
this bus. In addition, add a generic I2C device with 100 kHz bus speed
to the devicetree so that the OS will not switch to higher clock rates,
too.
Test= Measure the I2C signals at coreboot and OS runtime and ensure the
clock is always at 100 kHz.
Change-Id: I6b0a642cd3f5b77331663ac8c76ed0a116ae77ca
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/71227
Reviewed-by: Jan Samek <jan.samek@siemens.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Remove the PSE TSN GbE device #0 as it's unused on the board and not
visible during the PCI enumeration.
Change-Id: I4a7d0e437c4f4a12d3a07564cddeafb7c697c6d3
Signed-off-by: Jan Samek <jan.samek@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/70700
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Contrary to mc_ehl2, which this variant is based on, this board
doesn't contain the TI XIO2001 PCIe-to-PCI bridge, which makes the
attempts to modify the bridge's registers unnecessary.
Change-Id: I6597ceb78e4c790c08a0dfa9535dece33a8f95b8
Signed-off-by: Jan Samek <jan.samek@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/70854
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Based upon hardware differences from mc_ehl2, disable RP7
and enable RP3 and RP5.
Change-Id: Iecaa3098c3e4c9ce15254bb8bd1fe6da86d6e706
Signed-off-by: Jan Samek <jan.samek@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/70689
Reviewed-by: Uwe Poeche <uwe.poeche@siemens.com>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add a new mc_ehl variant, which is based on mc_ehl2 implementation.
This patch uses a copy of mc_ehl2 with changes only in naming
as a starting point for the new mc_ehl3 variant.
Follow-up patches will introduce the functional changes against
mc_ehl3.
Change-Id: Ie8c18b4f16d88b175ce576c2ef4c2e6ee0b4c306
Signed-off-by: Jan Samek <jan.samek@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/70688
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
<device/mmio.h>` chain-include `<arch/mmio.h>:
https://doc.coreboot.org/contributing/coding_style.html#headers-and-includes
Also sort includes while on it.
Change-Id: Ie62e4295ce735a6ca74fbe2499b41aab2e76d506
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/70291
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Found using 'Wmissing-include-dirs' command option.
Change-Id: Ie9ff43432215ebc89e6c1ea5f86b248e7fecd943
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/70396
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
GSPI2 interface is not used on this mainboard and can be disabled. It
will in addition remove the warning of a leftover static device in the
log.
Change-Id: I6e7462312953d50385ca7bb2f2e0abb8fc3a5886
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69972
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
|
|
As for mainboard mc_ehl1, a hard real-time dependency is also required
for this mainboard. The L1 prefetcher on Elkhart Lake is too aggressive
which in the end leads to an increased number of cache misses. Disabling
the L1 prefetcher boosts up the performance (in some cases by more than
10 %) in this specific use case.
Change-Id: I07b27dd672533e693a6c2987d16f54333850760e
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69966
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
Set downshift counter to 2 for all Marvell PHYs on this mainboard before
the PHY downshifts to the next highest speed.
Change-Id: I32b5f25a3e1e0f962dff3110143e236992ef8e7d
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69887
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
On this mainboard Marvell PHY INTn is routed to LED[2] pin.
Change-Id: I28a78afdcf0599bb998f906ce8056a0586e24f33
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69434
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This mainboard has three Marvel PHYs connected to the internal SOC GbE
controllers. The default LED status after HW reset of this PHYs shows a
different mode than what is needed. LED[2] is not connected on this
mainboard.
This patch sets the following LED status:
LED[0] - 7 = On - 1000 Mbps Link, Off - Else
LED[1] - 1 = On - Link, Blink - Activity, Off - No Link
LED[2] - not connected
TEST=Try different register values to verify LED feature.
Change-Id: I51d817bc720bf787279777f503efdc17dbb1274d
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69387
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
device
Instead of creating a dummy I2C device in order to force Linux to
decrease the I2C bus speed, use the own 'bus_speed' field of RV3028
device config structure.
Linux should always set the bus speed to the speed of the slowest
device sitting on the bus. Hence the dummy device is not needed
here anymore.
BUG=none
TEST=See if the RV3028 RTC is visible and working (date/time can
be set/read) in Linux. At the time, a driver modification is needed
to add a match table for the "MCRY3028" ACPI HID. A proper kernel
patch is pending.
Change-Id: I6e269dc67d1fe2a6747fcf3bee224def7b553f08
Signed-off-by: Jan Samek <jan.samek@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69544
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
|
|
Provide timing parameter for SSDT generation to achieve the requested
100 kHz speed with a high accuracy.
Test: Measure I2C bus clock, high and low times during I2C access from
Linux and confirm they match the specification.
Change-Id: Ifb6019421b612133b8f25c076519bc0e7200dad8
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69307
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
In Linux, the I2C speed defaults to 400 kHz if there is no device
registered in ACPI which requests a different speed. Due to board
limitations (layout, bus load), 400 kHz are too fast which results in a
timing violation. Therefore, add a dummy I2C device to both used I2C
buses (I2C1 and I2C2) with a speed of 100 kHz. This will limit the bus
speed in Linux accordingly.
Change-Id: I507c53c9ec7f763cef18903609231b1a66ed98fa
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69306
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
|
|
The SPD data for DRAM init has moved into the hwinfo data structure and
is therefore not used from spd.bin anymore. spd.bin will not receive any
updates, changes will only be done in hwinfo. There is no reason to keep
spd.bin around so remove it for both variants.
Change-Id: Ie6091b655ba7ff2e01b684266ce34b85593b8623
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68908
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Enable early POST code output for this mainboard, using
the NC FPGA device on PCIe.
This requires the parent PCI bridge to be initialized early.
BUG=none
TEST=boot on siemens/mc_apl2 and observe whether the POST
codes coming from before FSP-M init are visible
Change-Id: Ice5fe26e11d0513e6bb0a20f1d8f0483d7b3dc6a
Signed-off-by: Jan Samek <jan.samek@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68743
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Uwe Poeche <uwe.poeche@siemens.com>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
The highly real time driven application executed on mc_ehl1 has shown
that the L1 prefetcher on Elkhart Lake is too aggressive which in the
end leads to an increased number of cache misses. Disabling the L1
prefetcher boosts up the performance (in some cases by more than 10 %)
in this specific use case.
Change-Id: Id09a7f8f812707cd05bd5e3b530e5c3ad8067b16
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68668
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
|
|
Add a config for FIVR in devicetree for both, mc_ehl1 and mc_ehl2
variants in order to provide the real delay value for the VCC supply
rail. This delay is needed to enable proper switching between different
VCC levels based on current system state.
Change-Id: Ibccb8ea1b42ccd2ff0a37cbd9651528a2a55ebd6
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68666
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Apollo Lake seems to start with PCIe root ports unusable/uninitialized
before FspMemoryInit() is called and FSP-M properly initializes these
root ports.
However, we need the root ports accessible before FspMemoryInit() in
certain cases, such as emitting POST codes through a PCIe device.
For the initialization to happen properly, certain register writes
specified in Apollo Lake IAFW BIOS spec, vol. 2 (#559811), chapter
3.3.1 have to be done.
BUG=none
TEST=Boot on siemens/mc_apl2 with NC_FPGA_POST_CODE enabled and check
that the POST codes are emitted before FspMemoryInit().
Change-Id: If782bfdd5f499dd47c085a0a16b4b15832bc040e
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Signed-off-by: Jan Samek <jan.samek@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68223
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The intention of predefining driver strength is to avoid that the OS
SD-Card driver changes this setting.
Change-Id: I02fdac94462da1cd77f8dc972faf16f28d94c946
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68166
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
Add the gma-mainboard.ads for display output definition and enable the
libgfxinit usage in mainboard Kconfig.
Change-Id: I7e7a44736a8136b5320821e744134c7d64c7f1b4
Signed-off-by: Jan Samek <jan.samek@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67683
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Enable early initialization of the PTN3460 DP-to-LVDS bridge on this
board in order to allow showing the bootsplash screen at coreboot
runtime.
Change-Id: Ib1b727cef5fb8bea2d6d6c9896ad0107caeea51a
Signed-off-by: Jan Samek <jan.samek@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67682
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-by: Uwe Poeche <uwe.poeche@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Since there are no legacy devices on the variant mc_apl7 do not wait
for them on mc_apl7.
Change-Id: Ia4e6c0fb495a347be51bd6604a1d9b73098fb7b6
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67684
Reviewed-by: Jan Samek <jan.samek@siemens.com>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Due to layout restrictions on mc_ehl2, the SD-card interface is limited
to operate in DDR50 mode. The alternative modes SDR104 and SDR50 are not
supported. Limit the capabilities in the SD card controller to DDR50
mode only so that the SD card driver in OS will choose the right mode
for operation even if the attached SD card supports higher modes.
Change-Id: Idc7f1466ec71f4218f6b957cadeeffadd069eb2d
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67169
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
|
|
Since the new RTC is located in I2C bus 1 now, set the bus speed to
100 kHz as well.
Change-Id: Ica9468e559bc654545592a9b4d23f3164eafca8a
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67102
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Since the latest redesign a new RTC was introduced on mc_ehl2. Instead
of the old RX6110SA the new Micro Crystal RTC RV3028 is used now. Since
the address of this new RTC conflicts with an EEPROM on I2C bus 2, the
new RTC was moved to I2C bus 1.
As the mainboard is not finished yet, there are no incompatibility
issues with this change. Every new mainboard will have the new RTC and
the older mainboards are not delivered yet.
Change-Id: I3dd00855b8c9b22bdea21d3c8563cdb392868751
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67101
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
|
|
With a redesign of mc_ehl2 the used RTC was changed. In order to be able
to select a different RTC type for every variant move the RTC Kconfig
switch into the variant's Kconfig file.
Change-Id: Ia24703ede6a935e3b9886df87237857baec7d6a0
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67100
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
It is highly unlikely that the "OEM revision" of the DSDT is 0x20110725
on mainboards with a chipset not yet released on 2011-07-25. Since this
comment is most likely to have been copy-pasted from other boards, drop
it from boards which use a chipset newer than Sandy/Ivy Bridge.
Change-Id: If2f61d09082806b461878a76b286204ae56bf0eb
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66715
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Tarun Tuli <taruntuli@google.com>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
|
|
These comments don't add much value, so remove them.
Change-Id: I7e9692e3fe82345cb7ddcb11c32841c69768cd36
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66713
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Tarun Tuli <taruntuli@google.com>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
|
|
mc_apl7 does not use security features like VBOOT and TPM.
Test: flash mc_apl4 mainboard and ensure the disabled features via log.
Change-Id: I16683b92deb047208848b69c5aa79dc4212ce930
Signed-off-by: Uwe Poeche <uwe.poeche@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/65284
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
This patch adds a new mainboard variant called mc_apl7 which is based
on mc_apl4. So far only the names have been adjusted with no further
changes. Following commits will introduce the needed changes for this
mainboard variant.
Test: build mc_apl7, flash to mc_apl4 and compare log level 8 output
Change-Id: Ie9f2f5c29d071de442f8f3e3eaf4b3c2a6b8920f
Signed-off-by: Uwe Poeche <uwe.poeche@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/65283
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Hook Up SataPortsEnable to the devicetree. As the default value is 0,
set both [0] and [1] in all mainboards so they aren't affected.
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Change-Id: Ica8cf9484a6e6fe4362eabb8a9a59fcaf97c1bd3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/64524
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Select `HAVE_HYPERTHREADING` and hook up the hyper-threading setting
from the FSP to the option API so that related mainboards don't have to
do that. Unless otherwise configured (e.g. the CMOS setting or overriden
by the mainboard code), the value from the Kconfig setting
`FSP_HYPERTHREADING` is used.
Also, remove related code from the following mainboards, since it is
obsolete now.
* siemens/chili
* starlabs/laptop/cml
Change-Id: I173b87da5ce76549672c50ba30204cd77be8b82f
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/60544
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sean Rhodes <sean@starlabs.systems>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Disable RAPL for all mainboards based on mc_ehl for stable real time
mode of CPUs.
Test: Boot mc_ehl1 with this patch and ensure the bits in the MCBAR
register are cleared.
Change-Id: Ie58a4b6444d5be088ac2b25ff0a2f5cd33120ace
Signed-off-by: Uwe Poeche <uwe.poeche@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63548
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
There are three external Marvell PHY 88E1512 on this mainboard. The PHY
IRQ comes with a falling edge but the EHL MAC side needs a rising edge
signal. For that reason, we need an inversion of the IRQ polarity.
Change-Id: Id3caf582b4434b046779f5733e6ad9b57528ce35
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63889
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
Based on quick fix on this commit 7b0fe59be (soc/intel/ehl: Fix
logical bug for PseTsnGbePhyInterfaceType), disable PSE TSN
SGMII as the original intention is to set the PSE TSN phy
interface as RGMII.
Signed-off-by: Lean Sheng Tan <sheng.tan@9elements.com>
Change-Id: Id2e05b19f156621a945110791038bc0d19a0aad0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/64491
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
|
|
There are two APL specific config switches for RAPL and min. cpu clock
(APL_SKIP_SET_POWER_LIMITS, APL_SET_MIN_CLOCK_RATIO). These switches
could be used in future in other CPU platforms. Move them to common code
instead of having them just for one SOC.
Test: Make sure that the clock ratio (MSR 0x198) and the RAPL settings
(MSR0x610) do not change with this patch applied on mc_apl{1,4,5}
mainboard.
Change-Id: I3d63d1b9b6c96586a3c20bf8c1d8001b1d7c4bed
Signed-off-by: Uwe Poeche <uwe.poeche@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63546
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
repalcement ---> replacement
Change-Id: I486170e89f75fa7c01c7322bb8db783fd4f61931
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/64404
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Program the `SmbusEnable` FSP UPD according to the SMBus PCI device's
state in the devicetree. This avoids having to manually make sure the
SMBus PCI device and the `SmbusEnable` setting are in sync.
Change-Id: I275a981f914a55dc57a75e7d436912ff0255a293
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/64402
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
On this mainboard there are legacy PCI devices connected behind a
PCIe-2-PCI bridge. Not all clock outputs of this bridge are used. This
patch disables the unused PCI clock outputs on the XIO2001 bridge.
Change-Id: Iedbf0abfa554e0a6ad5b1d1741f4e9934103d171
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63931
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This variant uses all three EHL Ethernet GbE-TSN Controller so enable
the TSN GbE driver in order to set the needed MAC addresses. The
required function to retrieve a valid MAC address was already implement
in the common mainboard.c for mc_ehl.
TEST:
- Boot mc_ehl2 into Linux and check MAC addr via 'ip a'
Change-Id: Ia052c44feb606f9e1d31d047f2acc67e3226a895
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63864
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
TSN runs in SGMII mode on this mainboard. This requires setting the link
speed to 1 Gbps.
Change-Id: I9f1da971b4de5671d6d38be6dbc50edbbe20d157
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/64033
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
This mainboard uses all three internal Ethernet GbE-TSN controllers. Two
of them are initialized by the Programmable Services Engine (PSE).
This patch enables the Serial Gigabit Media Independent Interface
(SGMII) mode for GbE PSE0 and GbE PSE1. By setting PCH PSE DMA pins to
host owned, the IO is under control of the IA processor cores through
system software.
TEST:
- Boot mc_ehl2 into Linux and check inet addr via 'ip a'
Change-Id: I74e660548b2c44d5dbdb6023d5a36cfdd7e96f43
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63862
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
Break TPM related Kconfig into the following dimensions:
TPM transport support:
config CRB_TPM
config I2C_TPM
config SPI_TPM
config MEMORY_MAPPED_TPM (new)
TPM brand, not defining any of these is valid, and result in "generic" support:
config TPM_ATMEL (new)
config TPM_GOOGLE (new)
config TPM_GOOGLE_CR50 (new, implies TPM_GOOGLE)
config TPM_GOOGLE_TI50 (new to be used later, implies TPM_GOOGLE)
What protocol the TPM chip supports:
config MAINBOARD_HAS_TPM1
config MAINBOARD_HAS_TPM2
What the user chooses to compile (restricted by the above):
config NO_TPM
config TPM1
config TPM2
The following Kconfigs will be replaced as indicated:
config TPM_CR50 -> TPM_GOOGLE
config MAINBOARD_HAS_CRB_TPM -> CRB_TPM
config MAINBOARD_HAS_I2C_TPM_ATMEL -> I2C_TPM && TPM_ATMEL
config MAINBOARD_HAS_I2C_TPM_CR50 -> I2C_TPM && TPM_GOOGLE
config MAINBOARD_HAS_I2C_TPM_GENERIC -> I2C_TPM && !TPM_GOOGLE && !TPM_ATMEL
config MAINBOARD_HAS_LPC_TPM -> MEMORY_MAPPED_TPM
config MAINBOARD_HAS_SPI_TPM -> SPI_TPM && !TPM_GOOGLE && !TPM_ATMEL
config MAINBOARD_HAS_SPI_TPM_CR50 -> SPI_TPM && TPM_GOOGLE
Signed-off-by: Jes B. Klinke <jbk@chromium.org>
Change-Id: I4656b2b90363b8dfd008dc281ad591862fe2cc9e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63424
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
DDR4 SPD data needs to be 512 byte to comply with the spec.
Though there is no vital timing data used beyond 256 byte there are some
part information which will be used to show the part info in the
coreboot log. If the buffer is too small this log shows garbage.
This patch increases the SPD buffer size from 256 byte to 512 to avoid
side effects.
Change-Id: I5b88df7818cfd62b3579d69f9f5bb14880f49c8c
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62698
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Shorten define names containing PCI_{DEVICE,VENDOR}_ID_ with
PCI_{DID,VID}_ using the commands below, which also take care of some
spacing issues. An additional clean up of pci_ids.h is done in
CB:61531.
Used commands:
* find -type f -exec sed -i 's/PCI_\([DV]\)\(EVICE\|ENDOR\)_ID_\([_0-9A-Za-z]\{2\}\([_0-9A-Za-z]\{8\}\)*[_0-9A-Za-z]\{0,5\}\)\t/PCI_\1ID_\3\t\t/g'
* find -type f -exec sed -i 's/PCI_\([DV]\)\(EVICE\|ENDOR\)_ID_\([_0-9A-Za-z]*\)/PCI_\1ID_\3/g'
Change-Id: If9027700f53b6d0d3964c26a41a1f9b8f62be178
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39331
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
|
|
In order to achieve a stable eMMC interface disable the HS400 capability
of the host controller. This will result in an operating mode of maximum
HS200 (200 MHz single data rate) which leads to a more relaxed timing.
Change-Id: I0e125dd569b00f59ae0fd2f76169c4461291b47a
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62325
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
|
|
On mc_apl2 the external RTC is connected to I2C bus 3. All other I2C bus
devices (16.0, 16.1 and 16.2) have been disabled as they are not used.
While coreboot can handle the case where a PCI device does not have
function 0 enabled but a later one (here function 3), Linux seems to
check for function 0 first and ignores the rest if function 0
is missing. So enable PCI device 16.0 in order to let Linux use 16.3
again.
Test=Boot into Linux and make sure that PCI device 16.0 and 16.3 are
visible and I2C attached RTC works properly.
Change-Id: I55a748b6de8128f4b26b908118feff9f06d3fb7c
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62215
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
The mainboards mc_apl{2,4,5,6} use VBOOT for verification and can be in
a recovery state for different reasons. In this case we still want the
MRC cache to be around to avoid the DRAM retraining on every boot.
This patch enables the Kconfig switch HAS_RECOVERY_MRC_CACHE which makes
the already available MRC recovery region in FMAP useable.
Test=Boot mc_apl2 in recovery mode and make sure the recovery MRC
cache is used.
Change-Id: I2ea4993f05dd87a0e637f55e84b4fc06f5e29ecc
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61827
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
|
|
With latest hardware revision only PCIe RP2 and RP7 are used on this
mainboard.
Change-Id: I7702c2b9058dde1c819cb1df8a68fd602f5997da
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61415
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
With latest hardware revision SATA interface is no longer used on this
mainboard. The mainboard is still in development and not yet released
and for this reason there may still be adjustments.
Change-Id: Icbf088ce4c907e207f6f5d11b8bf5556fe2c90d6
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61414
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
Aggressive Link Power Management are no longer supported on these
mainboards and must therefore be disabled. This feature can have a
negative impact on the real-time behavior of the systems.
TEST:
- Boot into system software on mc_apl1
Change-Id: I8b08381743018790a20273ea1f61e5b0a56e6015
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61402
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
In order to guarantee data integrity an expired TCO must not hard reset
the board. Select the Kconfig switch to prevent this reset.
Change-Id: I04080c6bcd486e3a406438cc7a703165bb6945a0
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61178
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
The only option to make HECI1 function disable on Elkhart Lake SoC
platform is using SBI under SMM mode.
List of changes:
1. Drop `HeciEnabled` from dt and dt chip configuration.
2. Replace all logic that disables HECI1 based on the `HeciEnabled`
chip config with `DISABLE_HECI1_AT_PRE_BOOT` config.
Mainboards that choose to make HECI1 enable during boot don't override
`heci1 disable` config.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I76c625e6221fdef1343599e7dbc7739caa91bf98
Reviewed-on: https://review.coreboot.org/c/coreboot/+/60727
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sheng Lean Tan <sheng.tan@9elements.com>
|
|
Found using:
diff <(git grep -l '#include <console/console.h>' -- src/) <(git grep -l 'console_time_report\|console_time_get_and_reset\|do_putchar\|vprintk\|printk\|console_log_level\|console_init\|get_log_level\|CONSOLE_ENABLE\|get_console_loglevel\|die_notify\|die_with_post_code\|die\|arch_post_code\|mainboard_post\|post_code\|RAM_SPEW\|RAM_DEBUG\|BIOS_EMERG\|BIOS_ALERT\|BIOS_CRIT\|BIOS_ERR\|BIOS_WARNING\|BIOS_NOTICE\|BIOS_INFO\|BIOS_DEBUG\|BIOS_SPEW\|BIOS_NEVER' -- src/) |grep "<"
Change-Id: I9116965512a5b3241fd7e28537d96637008b31e4
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/60919
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Run the command below to fix all occurrences.
$ git grep -l 'ramstage\*/' | xargs sed -i 's,ramstage\*/,ramstage */,'
Change-Id: Ied155d325846fc0ef3e823e5708c6f74e3d7998f
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/60247
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
