| Age | Commit message (Collapse) | Author |
|---|
|
As discused earlier, the callback name 'mb_adjust_cfg' was considered
too generic. The new naming is chosen to be consistent with other
drivers' callback names designed to be used at mainboard level.
Also other functions, namely 'mb_get_edid' and 'mb_select_edid_table'
are renamed accordingly.
BUG=none
TEST=Builds for siemens/mc_apl{1,4,5,7} and siemens/mc_ehl boards
complete successfully.
Change-Id: I4cbec0e72e5f03e94df0faa36765d1a6cd873a7a
Signed-off-by: Jan Samek <jan.samek@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/72629
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
There were two wrong comments in all mc_ehl gpio.c files. This patch
corrects the incorrect comments.
Change-Id: Iea356db177227d89b91be32a4e2367c612b77350
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/72458
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This mainboard does not use security features like TPM.
Change-Id: Ieebbf12fc844573ffadb089da78062dd2033517a
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/72429
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
The upcoming mc_ehl4 variant is the first Siemens Elkhart Lake mainboard
without a TPM. For this reason, the corresponding Kconfig switches must
be moved to variant level. To prevent Jenkins build from complaining,
the TPM is removed in the following patch.
Change-Id: Ic73ccd1b52e57c1cf1dd7337b0e28beaadbece8e
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/72428
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
Measurements have shown that the automatic calibrated values for RGMII
output impedances are too low. For this reason, set the PMOS value to 16
and the NMOS to 13.
Change-Id: Ic3382889d3281faccb03819f9680a9763703b2a1
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73019
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This mainboard is based on mc_ehl1. In a first step, it contains a copy
of mc_ehl1 directory with minimum changes. Special adaptations for
mc_ehl4 mainboard will follow in separate commits.
Change-Id: I3c1f2cf4a3dcae58895f6d14a7fce46b2825e6ba
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/72427
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
With the latest hardware revision, the two GPIOs GPP_B15 and GPP_E19 are
no longer connected to a native function.
BUG=none
TEST=Checked output verbose GPIO debug messages
Change-Id: I266612f041b749aa83b366497b4211fc075c7bd7
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73341
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jan Samek <jan.samek@siemens.com>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
The currently used panel type could work with 500 ms but increasing
the value to 1 second allows to use a wider range of LVDS LCD panels,
as many of them specify the delay of 1 s as minimum.
BUG=none
TEST=Test link stability using a panel with minimum re-power delay of
1 s.
Change-Id: I2dd86e791c1212b67a80d7e6cfc474ad91b26c6b
Signed-off-by: Jan Samek <jan.samek@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/72804
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
Contents of the EDID are passed by a reference to an array
of length 0x80, for which the macro 'PTN_EDID_LEN' has already
been around.
This patch makes use of this macro within the driver and mainboard
implementation utilizing it.
BUG=none
TEST=A successful build of mc_apl{1,4,5,7} and mc_ehl3 mainboards.
Change-Id: If7d254aaf45d717133bb426bd08f8f9fe5c05962
Signed-off-by: Jan Samek <jan.samek@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/72653
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
|
|
Change-Id: Id8e1a52279e6a606441eefe30e24bcd44e006aad
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69815
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Jonathon Hall <jonathon.hall@puri.sm>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jakub Czapiga <jacz@semihalf.com>
|
|
Since the PSE GBE0 MAC has been disabled on this board in
commit 343644006f89 ("mb/siemens/mc_ehl3/devicetree.cb:
Remove TSN GbE 0"), therefore disable the corresponding
GPIOs as well.
BUG=none
TEST=Test link detection and IP assignment on the remaining
ports (PSE GBE1 and PCH GBE0) of mc_ehl3.
Change-Id: Ifa055f58894688471d68b9b93fcb994fdcb2a568
Signed-off-by: Jan Samek <jan.samek@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/72449
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The parallel mp code picks up lapics at runtime, so remove it from all
devicetrees that use this codebase.
Change-Id: I5258a769c0f0ee4bbc4facc19737eed187b68c73
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69303
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Return generic coreboot error codes from the mb_adjust_cfg
callback used in mainboards instead of '-1' constant and
a driver-specific success-indicating define.
BUG=none
TEST=Boards siemens/mc_apl{1,4,5,7} and siemens/mc_ehl3
build correctly.
Change-Id: I5e0d4e67703db518ed239a845f43047f569b94ec
Signed-off-by: Jan Samek <jan.samek@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/72071
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
With the addition of the mc_ehl3 board variant, a few
points about commenting the code arose either from the
review or during the implementation itself.
This patch unifies structure of these files, which
have a similar structure across more Siemens boards
utilizing the PTN3460 eDP-to-LVDS bridge.
BUG=none
TEST=Check that images for the affected boards can be
built.
Change-Id: I59820362e1f87e296c5548b9c3cecba4d2710fe7
Signed-off-by: Jan Samek <jan.samek@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/72068
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This board contains in addition to its base variant, mc_ehl2,
an LCD panel driven through the PTN3460 eDP-to-LVDS bridge.
This patch enables the PTN3460 support by adding the device to
devicetree.cb and board-specific configuration parameters in
lcd_panel.c, based upon a similar implementation in siemens/mc_apl7.
BUG=none
TEST=Boot with the LCD panel attached and observe whether
the picture is stable and free of artifacts coming from wrong
resolution, timing etc.
Change-Id: Ib8a1a6f47053406e42554c2dd33684165d54be08
Signed-off-by: Jan Samek <jan.samek@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/70692
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
The {read,write}{16,32}() functions used in this file come from the
mmio.h header, so include it directly.
BUG=none
TEST=Read out the SD card controller (device 1a.1) PCI registers
in Linux and check whether the values reflect the ones defined
in this file.
Change-Id: Iff7b55ef2bf98371b7d7d9114ccf3ebed64772a2
Signed-off-by: Jan Samek <jan.samek@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/72009
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
Change MAINBOARD_PART_NUMBER Kconfig value for mc_ehl3
from "MC_EHL3" to "MC EHL3".
Change-Id: Ie548607c5fb62faaed4921af714bc9b912e558a8
Signed-off-by: Jan Samek <jan.samek@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/71775
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
<gpio.h> chain-include <soc/gpio.h>.
Change-Id: Ia57d5cd33c70b6a755babd4db56c64c0e3666f9f
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/71817
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Enable the real-time tuning to improve performance in the real-time
environment for this mainboard.
Change-Id: I91ad7ca58add92b5cc66148aff8378890ee217eb
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/71234
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Due to mainboard restrictions a SATA link at Gen 3 (6 Gbps) can cause
issues as the margin is not big enough. Limit SATA speed to Gen 2 to
achieve a more robust SATA connection.
Change-Id: Ia79998db5f959528a4e8e29e570a7f55283adee1
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/71230
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Remove the PSE TSN GbE device #0 as it's unused on the board and not
visible during the PCI enumeration.
Change-Id: I4a7d0e437c4f4a12d3a07564cddeafb7c697c6d3
Signed-off-by: Jan Samek <jan.samek@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/70700
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Contrary to mc_ehl2, which this variant is based on, this board
doesn't contain the TI XIO2001 PCIe-to-PCI bridge, which makes the
attempts to modify the bridge's registers unnecessary.
Change-Id: I6597ceb78e4c790c08a0dfa9535dece33a8f95b8
Signed-off-by: Jan Samek <jan.samek@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/70854
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Based upon hardware differences from mc_ehl2, disable RP7
and enable RP3 and RP5.
Change-Id: Iecaa3098c3e4c9ce15254bb8bd1fe6da86d6e706
Signed-off-by: Jan Samek <jan.samek@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/70689
Reviewed-by: Uwe Poeche <uwe.poeche@siemens.com>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add a new mc_ehl variant, which is based on mc_ehl2 implementation.
This patch uses a copy of mc_ehl2 with changes only in naming
as a starting point for the new mc_ehl3 variant.
Follow-up patches will introduce the functional changes against
mc_ehl3.
Change-Id: Ie8c18b4f16d88b175ce576c2ef4c2e6ee0b4c306
Signed-off-by: Jan Samek <jan.samek@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/70688
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
<device/mmio.h>` chain-include `<arch/mmio.h>:
https://doc.coreboot.org/contributing/coding_style.html#headers-and-includes
Also sort includes while on it.
Change-Id: Ie62e4295ce735a6ca74fbe2499b41aab2e76d506
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/70291
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Found using 'Wmissing-include-dirs' command option.
Change-Id: Ie9ff43432215ebc89e6c1ea5f86b248e7fecd943
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/70396
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
GSPI2 interface is not used on this mainboard and can be disabled. It
will in addition remove the warning of a leftover static device in the
log.
Change-Id: I6e7462312953d50385ca7bb2f2e0abb8fc3a5886
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69972
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
|
|
As for mainboard mc_ehl1, a hard real-time dependency is also required
for this mainboard. The L1 prefetcher on Elkhart Lake is too aggressive
which in the end leads to an increased number of cache misses. Disabling
the L1 prefetcher boosts up the performance (in some cases by more than
10 %) in this specific use case.
Change-Id: I07b27dd672533e693a6c2987d16f54333850760e
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69966
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
Set downshift counter to 2 for all Marvell PHYs on this mainboard before
the PHY downshifts to the next highest speed.
Change-Id: I32b5f25a3e1e0f962dff3110143e236992ef8e7d
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69887
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
On this mainboard Marvell PHY INTn is routed to LED[2] pin.
Change-Id: I28a78afdcf0599bb998f906ce8056a0586e24f33
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69434
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This mainboard has three Marvel PHYs connected to the internal SOC GbE
controllers. The default LED status after HW reset of this PHYs shows a
different mode than what is needed. LED[2] is not connected on this
mainboard.
This patch sets the following LED status:
LED[0] - 7 = On - 1000 Mbps Link, Off - Else
LED[1] - 1 = On - Link, Blink - Activity, Off - No Link
LED[2] - not connected
TEST=Try different register values to verify LED feature.
Change-Id: I51d817bc720bf787279777f503efdc17dbb1274d
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69387
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
device
Instead of creating a dummy I2C device in order to force Linux to
decrease the I2C bus speed, use the own 'bus_speed' field of RV3028
device config structure.
Linux should always set the bus speed to the speed of the slowest
device sitting on the bus. Hence the dummy device is not needed
here anymore.
BUG=none
TEST=See if the RV3028 RTC is visible and working (date/time can
be set/read) in Linux. At the time, a driver modification is needed
to add a match table for the "MCRY3028" ACPI HID. A proper kernel
patch is pending.
Change-Id: I6e269dc67d1fe2a6747fcf3bee224def7b553f08
Signed-off-by: Jan Samek <jan.samek@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69544
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
|
|
Provide timing parameter for SSDT generation to achieve the requested
100 kHz speed with a high accuracy.
Test: Measure I2C bus clock, high and low times during I2C access from
Linux and confirm they match the specification.
Change-Id: Ifb6019421b612133b8f25c076519bc0e7200dad8
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69307
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
In Linux, the I2C speed defaults to 400 kHz if there is no device
registered in ACPI which requests a different speed. Due to board
limitations (layout, bus load), 400 kHz are too fast which results in a
timing violation. Therefore, add a dummy I2C device to both used I2C
buses (I2C1 and I2C2) with a speed of 100 kHz. This will limit the bus
speed in Linux accordingly.
Change-Id: I507c53c9ec7f763cef18903609231b1a66ed98fa
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69306
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
|
|
The SPD data for DRAM init has moved into the hwinfo data structure and
is therefore not used from spd.bin anymore. spd.bin will not receive any
updates, changes will only be done in hwinfo. There is no reason to keep
spd.bin around so remove it for both variants.
Change-Id: Ie6091b655ba7ff2e01b684266ce34b85593b8623
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68908
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
The highly real time driven application executed on mc_ehl1 has shown
that the L1 prefetcher on Elkhart Lake is too aggressive which in the
end leads to an increased number of cache misses. Disabling the L1
prefetcher boosts up the performance (in some cases by more than 10 %)
in this specific use case.
Change-Id: Id09a7f8f812707cd05bd5e3b530e5c3ad8067b16
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68668
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
|
|
Add a config for FIVR in devicetree for both, mc_ehl1 and mc_ehl2
variants in order to provide the real delay value for the VCC supply
rail. This delay is needed to enable proper switching between different
VCC levels based on current system state.
Change-Id: Ibccb8ea1b42ccd2ff0a37cbd9651528a2a55ebd6
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68666
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
The intention of predefining driver strength is to avoid that the OS
SD-Card driver changes this setting.
Change-Id: I02fdac94462da1cd77f8dc972faf16f28d94c946
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68166
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
Due to layout restrictions on mc_ehl2, the SD-card interface is limited
to operate in DDR50 mode. The alternative modes SDR104 and SDR50 are not
supported. Limit the capabilities in the SD card controller to DDR50
mode only so that the SD card driver in OS will choose the right mode
for operation even if the attached SD card supports higher modes.
Change-Id: Idc7f1466ec71f4218f6b957cadeeffadd069eb2d
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67169
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
|
|
Since the new RTC is located in I2C bus 1 now, set the bus speed to
100 kHz as well.
Change-Id: Ica9468e559bc654545592a9b4d23f3164eafca8a
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67102
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Since the latest redesign a new RTC was introduced on mc_ehl2. Instead
of the old RX6110SA the new Micro Crystal RTC RV3028 is used now. Since
the address of this new RTC conflicts with an EEPROM on I2C bus 2, the
new RTC was moved to I2C bus 1.
As the mainboard is not finished yet, there are no incompatibility
issues with this change. Every new mainboard will have the new RTC and
the older mainboards are not delivered yet.
Change-Id: I3dd00855b8c9b22bdea21d3c8563cdb392868751
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67101
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
|
|
With a redesign of mc_ehl2 the used RTC was changed. In order to be able
to select a different RTC type for every variant move the RTC Kconfig
switch into the variant's Kconfig file.
Change-Id: Ia24703ede6a935e3b9886df87237857baec7d6a0
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67100
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
It is highly unlikely that the "OEM revision" of the DSDT is 0x20110725
on mainboards with a chipset not yet released on 2011-07-25. Since this
comment is most likely to have been copy-pasted from other boards, drop
it from boards which use a chipset newer than Sandy/Ivy Bridge.
Change-Id: If2f61d09082806b461878a76b286204ae56bf0eb
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66715
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Tarun Tuli <taruntuli@google.com>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
|
|
These comments don't add much value, so remove them.
Change-Id: I7e9692e3fe82345cb7ddcb11c32841c69768cd36
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66713
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Tarun Tuli <taruntuli@google.com>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
|
|
Disable RAPL for all mainboards based on mc_ehl for stable real time
mode of CPUs.
Test: Boot mc_ehl1 with this patch and ensure the bits in the MCBAR
register are cleared.
Change-Id: Ie58a4b6444d5be088ac2b25ff0a2f5cd33120ace
Signed-off-by: Uwe Poeche <uwe.poeche@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63548
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
There are three external Marvell PHY 88E1512 on this mainboard. The PHY
IRQ comes with a falling edge but the EHL MAC side needs a rising edge
signal. For that reason, we need an inversion of the IRQ polarity.
Change-Id: Id3caf582b4434b046779f5733e6ad9b57528ce35
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63889
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
Based on quick fix on this commit 7b0fe59be (soc/intel/ehl: Fix
logical bug for PseTsnGbePhyInterfaceType), disable PSE TSN
SGMII as the original intention is to set the PSE TSN phy
interface as RGMII.
Signed-off-by: Lean Sheng Tan <sheng.tan@9elements.com>
Change-Id: Id2e05b19f156621a945110791038bc0d19a0aad0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/64491
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
|
|
repalcement ---> replacement
Change-Id: I486170e89f75fa7c01c7322bb8db783fd4f61931
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/64404
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Program the `SmbusEnable` FSP UPD according to the SMBus PCI device's
state in the devicetree. This avoids having to manually make sure the
SMBus PCI device and the `SmbusEnable` setting are in sync.
Change-Id: I275a981f914a55dc57a75e7d436912ff0255a293
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/64402
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
On this mainboard there are legacy PCI devices connected behind a
PCIe-2-PCI bridge. Not all clock outputs of this bridge are used. This
patch disables the unused PCI clock outputs on the XIO2001 bridge.
Change-Id: Iedbf0abfa554e0a6ad5b1d1741f4e9934103d171
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63931
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This variant uses all three EHL Ethernet GbE-TSN Controller so enable
the TSN GbE driver in order to set the needed MAC addresses. The
required function to retrieve a valid MAC address was already implement
in the common mainboard.c for mc_ehl.
TEST:
- Boot mc_ehl2 into Linux and check MAC addr via 'ip a'
Change-Id: Ia052c44feb606f9e1d31d047f2acc67e3226a895
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63864
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
TSN runs in SGMII mode on this mainboard. This requires setting the link
speed to 1 Gbps.
Change-Id: I9f1da971b4de5671d6d38be6dbc50edbbe20d157
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/64033
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
This mainboard uses all three internal Ethernet GbE-TSN controllers. Two
of them are initialized by the Programmable Services Engine (PSE).
This patch enables the Serial Gigabit Media Independent Interface
(SGMII) mode for GbE PSE0 and GbE PSE1. By setting PCH PSE DMA pins to
host owned, the IO is under control of the IA processor cores through
system software.
TEST:
- Boot mc_ehl2 into Linux and check inet addr via 'ip a'
Change-Id: I74e660548b2c44d5dbdb6023d5a36cfdd7e96f43
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63862
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
Break TPM related Kconfig into the following dimensions:
TPM transport support:
config CRB_TPM
config I2C_TPM
config SPI_TPM
config MEMORY_MAPPED_TPM (new)
TPM brand, not defining any of these is valid, and result in "generic" support:
config TPM_ATMEL (new)
config TPM_GOOGLE (new)
config TPM_GOOGLE_CR50 (new, implies TPM_GOOGLE)
config TPM_GOOGLE_TI50 (new to be used later, implies TPM_GOOGLE)
What protocol the TPM chip supports:
config MAINBOARD_HAS_TPM1
config MAINBOARD_HAS_TPM2
What the user chooses to compile (restricted by the above):
config NO_TPM
config TPM1
config TPM2
The following Kconfigs will be replaced as indicated:
config TPM_CR50 -> TPM_GOOGLE
config MAINBOARD_HAS_CRB_TPM -> CRB_TPM
config MAINBOARD_HAS_I2C_TPM_ATMEL -> I2C_TPM && TPM_ATMEL
config MAINBOARD_HAS_I2C_TPM_CR50 -> I2C_TPM && TPM_GOOGLE
config MAINBOARD_HAS_I2C_TPM_GENERIC -> I2C_TPM && !TPM_GOOGLE && !TPM_ATMEL
config MAINBOARD_HAS_LPC_TPM -> MEMORY_MAPPED_TPM
config MAINBOARD_HAS_SPI_TPM -> SPI_TPM && !TPM_GOOGLE && !TPM_ATMEL
config MAINBOARD_HAS_SPI_TPM_CR50 -> SPI_TPM && TPM_GOOGLE
Signed-off-by: Jes B. Klinke <jbk@chromium.org>
Change-Id: I4656b2b90363b8dfd008dc281ad591862fe2cc9e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63424
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
DDR4 SPD data needs to be 512 byte to comply with the spec.
Though there is no vital timing data used beyond 256 byte there are some
part information which will be used to show the part info in the
coreboot log. If the buffer is too small this log shows garbage.
This patch increases the SPD buffer size from 256 byte to 512 to avoid
side effects.
Change-Id: I5b88df7818cfd62b3579d69f9f5bb14880f49c8c
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62698
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Shorten define names containing PCI_{DEVICE,VENDOR}_ID_ with
PCI_{DID,VID}_ using the commands below, which also take care of some
spacing issues. An additional clean up of pci_ids.h is done in
CB:61531.
Used commands:
* find -type f -exec sed -i 's/PCI_\([DV]\)\(EVICE\|ENDOR\)_ID_\([_0-9A-Za-z]\{2\}\([_0-9A-Za-z]\{8\}\)*[_0-9A-Za-z]\{0,5\}\)\t/PCI_\1ID_\3\t\t/g'
* find -type f -exec sed -i 's/PCI_\([DV]\)\(EVICE\|ENDOR\)_ID_\([_0-9A-Za-z]*\)/PCI_\1ID_\3/g'
Change-Id: If9027700f53b6d0d3964c26a41a1f9b8f62be178
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39331
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
|
|
In order to achieve a stable eMMC interface disable the HS400 capability
of the host controller. This will result in an operating mode of maximum
HS200 (200 MHz single data rate) which leads to a more relaxed timing.
Change-Id: I0e125dd569b00f59ae0fd2f76169c4461291b47a
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62325
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
|
|
With latest hardware revision only PCIe RP2 and RP7 are used on this
mainboard.
Change-Id: I7702c2b9058dde1c819cb1df8a68fd602f5997da
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61415
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
With latest hardware revision SATA interface is no longer used on this
mainboard. The mainboard is still in development and not yet released
and for this reason there may still be adjustments.
Change-Id: Icbf088ce4c907e207f6f5d11b8bf5556fe2c90d6
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61414
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
In order to guarantee data integrity an expired TCO must not hard reset
the board. Select the Kconfig switch to prevent this reset.
Change-Id: I04080c6bcd486e3a406438cc7a703165bb6945a0
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61178
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
The only option to make HECI1 function disable on Elkhart Lake SoC
platform is using SBI under SMM mode.
List of changes:
1. Drop `HeciEnabled` from dt and dt chip configuration.
2. Replace all logic that disables HECI1 based on the `HeciEnabled`
chip config with `DISABLE_HECI1_AT_PRE_BOOT` config.
Mainboards that choose to make HECI1 enable during boot don't override
`heci1 disable` config.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I76c625e6221fdef1343599e7dbc7739caa91bf98
Reviewed-on: https://review.coreboot.org/c/coreboot/+/60727
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sheng Lean Tan <sheng.tan@9elements.com>
|
|
Found using:
diff <(git grep -l '#include <console/console.h>' -- src/) <(git grep -l 'console_time_report\|console_time_get_and_reset\|do_putchar\|vprintk\|printk\|console_log_level\|console_init\|get_log_level\|CONSOLE_ENABLE\|get_console_loglevel\|die_notify\|die_with_post_code\|die\|arch_post_code\|mainboard_post\|post_code\|RAM_SPEW\|RAM_DEBUG\|BIOS_EMERG\|BIOS_ALERT\|BIOS_CRIT\|BIOS_ERR\|BIOS_WARNING\|BIOS_NOTICE\|BIOS_INFO\|BIOS_DEBUG\|BIOS_SPEW\|BIOS_NEVER' -- src/) |grep "<"
Change-Id: I9116965512a5b3241fd7e28537d96637008b31e4
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/60919
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Run the command below to fix all occurrences.
$ git grep -l 'ramstage\*/' | xargs sed -i 's,ramstage\*/,ramstage */,'
Change-Id: Ied155d325846fc0ef3e823e5708c6f74e3d7998f
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/60247
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Enable TPM init in bootblock so that all further stages and other CBFS
files are directly measured into PCRs immediately instead of being
logged into a buffer and replayed to the TPM in ramstage.
Change-Id: Ib3ac29aa72abe8e967660ae7e8416aeb8812de26
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/60008
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
|
|
This board does not have a LPC or eSPI connection to the NC FPGA anymore
and therefore IO port 0x80 is not useable for POST codes anymore. Enable
the feature of sending the POST codes to the NC FPGA via PCI so that the
POST codes are visbile again in coreboot.
Change-Id: I9043e4ec9a2ad6b946e373bb3dce9da3d42d00d1
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59347
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
|
|
With latest hardware revision all clock outputs will be used on this
mainboard. For this reason set all clock source mappings to
'PCIE_CLK_FREE' to have a free running clock.
Change-Id: Ic3f6fb4e24128742ed72dade7a4555c39fb722ae
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59259
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
HECI #2 is not used for CSE communication. Therefore, it is not
necessary to set the parameter 'Heci2Enable' in devicetree.
Change-Id: I7012e4d877a464699727ca775af3f9965e0602e9
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58940
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
All the mainboard variants of mc_ehl do not use the external switches
for the bypass rails. Disable the matching UPDs and all the low power
modes of the PMC.
Change-Id: I08f4effe5c4d5845bed01dfe1bd1251c58012b7f
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58895
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-by: Lean Sheng Tan <lean.sheng.tan@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
In order to get a reliable real-time performance disable all P-States
for all mc_ehl based mainboard.
Change-Id: I22857cc0f1476483ca82c1c872e4519e4b350ea9
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58894
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lean Sheng Tan <lean.sheng.tan@intel.com>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
|
|
Disable all C-states other than C0/C1 for CPU and package.
Change-Id: I2c163f859dab4b0dc02896c70122e993cdd3db72
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58893
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lean Sheng Tan <lean.sheng.tan@intel.com>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
|
|
There are a bunch of devices in the devicetree that are disabled in
FSP-S and not used on this board. Having them around in the devicetree,
even if disabled, is not necessary and leads to a message in the log
(left over static devices...check your devicetree).
This commit cleans up devicetree.cb and removes all unused and disabled
devices.
Change-Id: I7486f9ba362c80b43b6c888a3b40a4c947218299
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58887
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
As a prevention of Row-Hammer attacks enable the FSP-M parameter
'RhPrevention'.
Change-Id: I52f68525e882aee26822d9b3c488639c00f27d17
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58856
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
This configures GPIO GPP_G5 as an input pin for SD card detect.
Change-Id: I708eb112fa054f2f88857001c409fb62493b6206
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58855
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
PCIe root ports #4 (00:1c.3) and #6 (00:1c.5) are currently not used on
this mainboard and are not routed either, so remove them from the
devicetree completely. PCIe root port #7 (00:1c.6) is connected and
used. Add the missing settings for L1 substates and latency reporting to
disable these features for this port as well.
Change-Id: I47e8528bea993ed527a0aecdbc93b94bbd9a7a49
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58853
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
On mc_ehl2 there are currently four of the six PCIe clocks used to drive
PCIe devices. None of the used clock output is dedicated to a special
device. Therefore do not use a port mapping of the clocks to avoid a
stopping clock once a device is missing and the matching root port is
disabled. Instead set the mapping to 'PCIE_CLK_FREE' to have a free
running clock.
In addition, use the defined constant 'PCIE_CLK_NOTUSED' instead of the
value 0xFF to disable the CLKREQ-feature and unused clocks.
Change-Id: I81419887b7f463a937917b971465245c1cb46b94
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58852
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Lean Sheng Tan <lean.sheng.tan@intel.com>
|
|
On mc_ehl1 there are three of the 6 PCIe clocks used to drive PCIe
devices. None of the used clock output is dedicated to a special device
(CLK0 drives several devices on the mainboard, CLK1 and CLK2 are
connected to a PCIe switch). Therefore do not use a port mapping of the
clocks to avoid a stopping clock once a device is missing and the
matching root port is disabled. Instead set the mapping to
'PCIE_CLK_FREE' to have a free running clock.
In addition, use the defined constant 'PCIE_CLK_NOTUSED' instead of the
value 0xFF to disable the CLKREQ-feature and unused clocks.
Change-Id: I2beea76ff8fefd79f476bef343d13495b45cdfcf
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58740
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
PCIe root ports #5 (00:1c.4) and #6 (00:1c.5) are not used on this
mainboard and are not routed either, so remove them from the devicetree
completely. PCIe root port #7 (00:1c.6) is connected and used. Add the
missing settings for L1 substates and latency reporting to disable these
features for this port as well.
Change-Id: I06f59f0369ffcd958b5fe12bb3c646d37103811f
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58568
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
There are a bunch of devices in the devicetree that are disabled in
FSP-S and not used on this board. Having them around in the devicetree,
even if disabled, is not necessary and leads to a message in the log
(left over static devices...check your devicetree).
This commit cleans up devicetree.cb and removes all unused and disabled
devices.
Change-Id: Ia5ffb382e3524e61b8583aca801063942fe2f247
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58567
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
|
|
Correct the PCH serial IO settings, suitable for this mainboard.
Change-Id: I3c9915b2d52fbc6a15ac1e68c77bfb3983f7b1cd
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58296
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
Correct the USB settings, suitable for this mainboard.
Change-Id: I691d91d2a76e27b8efdc18eeae737a78e9ae38fa
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58295
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
Correct the remaining PCI devices, differing from the ehl1 mainboard.
Change-Id: I8112fa5ea86e879741061798530150701b759156
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58294
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
This mainboard has its own coreboot ready LED. The LED is switched
on via GPIO GPP_F20.
Change-Id: I3570d691e90d2cb6e11b856b876f0327da118522
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58293
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
Since the DRAM population is fixed to both channels on all mc_ehl boards
there is no need to have this 'half_populated' variable at all.
Simply use a fixed 'false' in the call of 'memcfg_init()' and delete
this variable here.
Change-Id: I783c17e6d92322a8b0c094cce803108e718011fa
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58177
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
|
|
The preferred location for the SPD data on mc_ehl based boards is the
HW-Info data structure. Inside this structure there is a field of 128
bytes available for the SPD data. So in order to use it construct a
buffer in memory which is 256 bytes long (as FSP requests minimum 256
bytes for the SPD data) and where the upper 128 bytes are taken from
HW-Info holding the needed timing parameters for LPDDR4.
If there is a case where HW-Info is not accessible or where the
contained SPD data is not valid (by checking the CRC in HW-Info SPD)
fall back to fixed SPD data set in CBFS.
Change-Id: I2b6a1bde0306ba84f5214b876eaf76ca12d8f058
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58176
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
|
|
On this mainboard there is a legacy PCI device, which is connected to
the PCIe root port via a PCIe-2-PCI bridge. This device only supports
legacy interrupt routing. For this reason, we have to adjust the PIR8
register (0x3150) which is responsible for PCIe device 25h. The bridge
is connected to PCIe root port 7.
The following routing is required:
INTA#->PIRQC#, INTB#->PIRQD#, INTC#->PIRQA#, INTD#-> PIRQB#
TEST:
- Boot into system software
Change-Id: Id6bb8d00458c4d1e3fefd01ac3848078355868d9
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58172
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
In upcoming patches, we need mainboard specific adjustments.
Change-Id: Icf9d829b19b2d26a39ad34be4658064083e9da6d
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58171
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
|
|
Enable LPC ComB on this mainboard.
TEST:
- Boot Linux and check with 'dmesg | grep tty'
Change-Id: I7ec58685a723c177df18144011934b206e6425d0
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58170
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
|
|
This mainboard uses an eSPI-to-LPC bridge for console output. For this
reason, the internal LPSS UART must be disabled.
Change-Id: I86777cf719def331f4d257ddd94e9a87125ebce8
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58169
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
|
|
Set the GPIOs according to the circuit diagram for this mainboard.
Change-Id: I19dc24a16ee9f533b45879bf60fb441e24018cc8
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58168
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
|
|
This mainboard has only SATA Port 1 available with no device sleep
feature.
Change-Id: I338833f2f9bcb407599cfc676ead0b8a9d7379bd
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58167
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
|
|
This mainboard has SD slot available and therefore it should be enabled.
Change-Id: I0c97e2dc589bf6b89713a473925e42a20278f457
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58166
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
|
|
This board has the RTC RX6110SA connected to the I2C2 instead of SMBus
as in mc_ehl1. Set the bus speed for I2C2 to 100 kHz, since this RTC
only supports the standard speed.
TEST:
- Console Log shows no errors for RX6110SA during I2C2 init
- Finalize device for I2C 00:32 shows correct date and time
Change-Id: I679c6397fa0d213a25eebaf8a9e0bda9941acd26
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58112
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
Since this variant uses different DDR4 devices compared to mc_ehl1 in a
memory down configuration, the SPD data file must be adapted.
In a first configuration we use Micron MT53D512M32D2NP modules.
Following values were adjusted according to this board characteristic
and with help of Serial Presence Detect (SPD) for LPDDR3 and LPDDR4
SDRAM Modules JEDEC Spec and the Specification for this Micron modules
itself:
- SPD Byte 4 - only 4Gb density instead of 8Gb for mc_ehl1
- SPD Byte 5 - different Row and Column Address Bits
- SPD Byte 29/30 - 4Gb LPDDR4 needs 130ns tRFCab
- SPD Byte 31/32 - 4Gb LPDDR4 needs 60ns tRFCpb
Change-Id: Icb25f418952f0c96117140863d0d9c897d814ac5
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58111
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
There are currently two variants for mc_ehl where different UARTs are
used for the console. Move the Kconfig switch UART_FOR_CONSOLE to the
Kconfig of the variant and select the matching value there.
Change-Id: I7152013a0e32ff151b92932a47953705e591dc0d
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58052
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add a new variant of the mc_ehl board called mc_ehl2. This patch just
copies the files and renames things where needed.
Following patches will adapt the needed features for this new variant.
Change-Id: I3ec3c091017fd66fe6a09216203cdc7c9e833846
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58051
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
|
|
Enable LPSS UART for coreboot console on mc_ehl1.
Change-Id: Id995953741d48fbbe2482ff7c0ef81cac5a31207
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58049
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
|
|
Specify the type of the `DIMM_SPD_SIZE` Kconfig symbol once.
Change-Id: I619833dbce6d2dbe414ed9b37f43196b4b52730e
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57257
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Since all mainboards use `CHIPSET_LOCKDOWN_COREBOOT`, make it the
default by changing its enum value to 0 and remove its configuration
from all related devicetrees.
If `common_soc_config.chipset_lockdown` is not configured with
something else in the devicetree, then `CHIPSET_LOCKDOWN_COREBOOT`
is used.
Also, add a release note for the upcoming 4.15 release.
Change-Id: I369f01d3da2e901e2fb57f2c83bd07380f3946a6
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56967
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Tim Crawford <tcrawford@system76.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
|
|
Some legacy devices need to have the master bit set in the PCI config
due to old drivers not setting it correctly. Set the master bit if the
feature is enabled via Kconfig switch PCI_ALLOW_BUS_MASTER_ANY_DEVICE.
For now, the PCI devices with the ID 110a:403e and 110a:403f needs this
master bit to be set.
Change-Id: Id3f6bda97e5f47d0613a1db8f8adac0b158ab8b1
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56632
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Boards based on mc_ehl have, just like some mc_apl variants, legacy
devices on the PCI bus which take longer to boot. In order to ensure
that they will be enumerated correctly wait for them to come up before
PCI scan starts.
TEST=Checked that the new message is visible in the log.
Change-Id: If2f935b69ddaa9364566deacfada5e7d41fcdabd
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56631
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
