| Age | Commit message (Collapse) | Author |
|---|
|
Change-Id: Ied455ff29b151fb5f4bca26a189b1d4104d8cede
Signed-off-by: Martin Roth <gaumless@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80595
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This renames bus to upstream and link_list to downstream.
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Change-Id: I80a81b6b8606e450ff180add9439481ec28c2420
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78330
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Signed-off-by: Martin Roth <gaumless@gmail.com>
Change-Id: Ib69236fb5d68272f92405512dc231fa75ecccaa6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80125
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
The .inc suffix is confusing to various tools as it's not specific to
Makefiles. This means that editors don't recognize the files, and don't
open them with highlighting and any other specific editor functionality.
This issue is also seen in the release notes generation script where
Makefiles get renamed before running cloc.
Signed-off-by: Martin Roth <gaumless@gmail.com>
Change-Id: I4790adb41cb62c8c8dd44261a2926dfb6350955a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80111
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Erik van den Bogaert <ebogaert@eltan.com>
Reviewed-by: Maximilian Brune <maximilian.brune@9elements.com>
|
|
Selects should be done in the Kconfig file instead of Kconfig.name and
not mixed over both files.
Change-Id: Ic199a60013ceedfd15b191a5fe707be6654ad3a2
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75078
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
|
|
With the introduction of a new Linux version a problem has appeared
after a software initiated reset via CF9h register. The problem
manifests itself in the fact that the Linux kernel does not start after
the reboot. The problem is solved by setting bit 3 to 1 in Reset Control
Register (I/O port CF9h). This leads to the fact that the PCH will drive
SLP_S3 active low in the reset sequence. It leads to the same behavior
as in commit 04ea73ee78bc ("siemens/mc_apl3: Set Full Reset Bit into
Reset Control Register") explained.
Change-Id: Ibc6d538c939e38732f42995d5ec6c8b61f979a6a
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77603
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Jan Samek <jan.samek@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
To help identify the licenses of the various files contained in the
coreboot source, we've added SPDX headers to the top of all of the
.c and .h files. This extends that practice to Makefiles.
Any file in the coreboot project without a specific license is bound
to the license of the overall coreboot project, GPL Version 2.
This patch adds the GPL V2 license identifier to the top of all
makefiles in the mainboard directory that don't already have an SPDX
license line at the top.
Signed-off-by: Martin Roth <gaumless@gmail.com>
Change-Id: Ic451e68b1ad9ccdf34484dd98bd7fca7e177ef22
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68982
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Reviewed-by: Yidi Lin <yidilin@google.com>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Tim Crawford <tcrawford@system76.com>
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
|
|
With the previous instruction the complete register was set to '0'.
Correctly, only the bits 23:16 must be masked.
Change-Id: Idd6e70dcb42c69cf3bc5d36db993e6def52eba58
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76177
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jan Samek <jan.samek@siemens.com>
|
|
Because of an incorrect transmit voltage swing, the signal must be
adjusted. The factor of slices for full swing level can be corrected via
the High Speed I/O Transmit Control Register 3. The appropriate value of
0.7 V was determined by using an oscilloscope.
Change-Id: I965960004ca44f1b37b16ce6484000fa7fd8ad90
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76175
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jan Samek <jan.samek@siemens.com>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
|
|
The offset '0xa8c' for the High Speed I/O Transmit Control Register 3
refers to SATA port 1 only. To make this clear, change the name of the
define from 'TX_DWORD3' to 'TX_DWORD3_P1'.
Change-Id: I09d17eeffbe84939297e739586f6b74ed3e2258b
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76174
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Jan Samek <jan.samek@siemens.com>
|
|
A correction of Tx signal from SATA interface is not necessary on these
boards currently. Therefore remove the define and the corresponding code
on mc_apl5.
Change-Id: I5092ee128cb35e126069d18bb3cbd635e01bbcdb
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76173
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jan Samek <jan.samek@siemens.com>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
|
|
For a unification of the naming convension, change from pascal case to
snake case style for parameter 'DisableSataSalpSupport'.
Change-Id: I4a68ffd2b68c92434da681b5e5567329c8784c72
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75858
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
For a unification of the naming convension, change from pascal case to
snake case style for parameter 'SataPortsEnable'.
Change-Id: I0df35125360eb42a03d5445011d72842cb2b8d7e
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75553
Reviewed-by: Himanshu Sahdev <himanshu.sahdev@intel.com>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jan Samek <jan.samek@siemens.com>
|
|
There are only SSD connected to SATA ports on this mainboard. To prevent
misbehavior, set the correct hard drive type for enabled SATA ports.
BUG=none
TEST=Boot into OS and check the stability of the SSD
Change-Id: I2c2b0548865e87859a1d742295e09a731bfb3f76
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75367
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jan Samek <jan.samek@siemens.com>
|
|
Due to mainboard restrictions a SATA link at Gen 3 can cause issues as
the margin is not big enough. Limit SATA speed to Gen 2 to achieve a
more robust SATA connection.
Change-Id: Ifdea4542836b9c75b5507324fbb06b9566a6fe1d
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75365
Reviewed-by: Jan Samek <jan.samek@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
With the introduction of a new Linux version a problem has appeared
after a software initiated reset via CF9h register. The problem
manifests itself in the fact that the Linux kernel does not start after
the reboot. The problem is solved by setting bit 3 to 1 in Reset Control
Register (I/O port CF9h). This leads to the fact that the PCH will drive
SLP_S3 active low in the reset sequence. It leads to the same behavior
as in commit 04ea73ee78bc ("siemens/mc_apl3: Set Full Reset Bit into
Reset Control Register") explained.
Change-Id: Ia8b7f997ca6234add569da751e1070144790e258
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75041
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jan Samek <jan.samek@siemens.com>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
Change-Id: I6578aee52e6900b25441dc119383856acc480231
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75042
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jan Samek <jan.samek@siemens.com>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
As discused earlier, the callback name 'mb_adjust_cfg' was considered
too generic. The new naming is chosen to be consistent with other
drivers' callback names designed to be used at mainboard level.
Also other functions, namely 'mb_get_edid' and 'mb_select_edid_table'
are renamed accordingly.
BUG=none
TEST=Builds for siemens/mc_apl{1,4,5,7} and siemens/mc_ehl boards
complete successfully.
Change-Id: I4cbec0e72e5f03e94df0faa36765d1a6cd873a7a
Signed-off-by: Jan Samek <jan.samek@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/72629
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
Change-Id: I7eaf625e5acfcefdae7c81e186de36b42c06ee67
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/72704
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Reviewed-by: Sean Rhodes <sean@starlabs.systems>
|
|
Contents of the EDID are passed by a reference to an array
of length 0x80, for which the macro 'PTN_EDID_LEN' has already
been around.
This patch makes use of this macro within the driver and mainboard
implementation utilizing it.
BUG=none
TEST=A successful build of mc_apl{1,4,5,7} and mc_ehl3 mainboards.
Change-Id: If7d254aaf45d717133bb426bd08f8f9fe5c05962
Signed-off-by: Jan Samek <jan.samek@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/72653
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
|
|
Change-Id: Id8e1a52279e6a606441eefe30e24bcd44e006aad
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69815
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Jonathon Hall <jonathon.hall@puri.sm>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jakub Czapiga <jacz@semihalf.com>
|
|
The parallel mp code picks up lapics at runtime, so remove it from all
devicetrees that use this codebase.
Change-Id: I5258a769c0f0ee4bbc4facc19737eed187b68c73
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69303
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Return generic coreboot error codes from the mb_adjust_cfg
callback used in mainboards instead of '-1' constant and
a driver-specific success-indicating define.
BUG=none
TEST=Boards siemens/mc_apl{1,4,5,7} and siemens/mc_ehl3
build correctly.
Change-Id: I5e0d4e67703db518ed239a845f43047f569b94ec
Signed-off-by: Jan Samek <jan.samek@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/72071
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
Enable early POST code display on this variant using
the common mc_apl1 baseboard functionality.
BUG=none
TEST=Boot on mc_apl5 and observe that POST codes are
displayed before DRAM training.
Change-Id: I390e0ab09ca830637e7a991db77e994d6c358e75
Signed-off-by: Jan Samek <jan.samek@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/72386
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Enable early POST code display on this variant using
the common mc_apl1 baseboard functionality.
BUG=none
TEST=Boot on mc_apl6 and observe that POST codes are
displayed before DRAM training.
Change-Id: I2a52c241c383f8ebcf05052e9bc0ba13e63e3728
Signed-off-by: Jan Samek <jan.samek@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/72116
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
Move logic previously used only in the mc_apl2 variant to
the mainboard level so that other variants can also make
use of it without code duplication.
This functionality on the mc_apl6 variant will be enabled
in a follow-up patch.
BUG=none
TEST=Boot on siemens/mc_apl2 and observe that the POST
codes are displayed before DRAM training.
Change-Id: I762e328ad06c047d911ce1fc40f12a66cbd14e11
Signed-off-by: Jan Samek <jan.samek@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/72115
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
With the addition of the mc_ehl3 board variant, a few
points about commenting the code arose either from the
review or during the implementation itself.
This patch unifies structure of these files, which
have a similar structure across more Siemens boards
utilizing the PTN3460 eDP-to-LVDS bridge.
BUG=none
TEST=Check that images for the affected boards can be
built.
Change-Id: I59820362e1f87e296c5548b9c3cecba4d2710fe7
Signed-off-by: Jan Samek <jan.samek@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/72068
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Due to a high I2C bus load on the mainboard I2C frequency of 400 kHz
leads to poor signaling. Therefore limit the I2C speed to 100 kHz for
this bus. In addition, add a generic I2C device with 100 kHz bus speed
to the devicetree so that the OS will not switch to higher clock rates,
too.
Test= Measure the I2C signals at coreboot and OS runtime and ensure the
clock is always at 100 kHz.
Change-Id: I6b0a642cd3f5b77331663ac8c76ed0a116ae77ca
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/71227
Reviewed-by: Jan Samek <jan.samek@siemens.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Found using 'Wmissing-include-dirs' command option.
Change-Id: Ie9ff43432215ebc89e6c1ea5f86b248e7fecd943
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/70396
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Enable early POST code output for this mainboard, using
the NC FPGA device on PCIe.
This requires the parent PCI bridge to be initialized early.
BUG=none
TEST=boot on siemens/mc_apl2 and observe whether the POST
codes coming from before FSP-M init are visible
Change-Id: Ice5fe26e11d0513e6bb0a20f1d8f0483d7b3dc6a
Signed-off-by: Jan Samek <jan.samek@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68743
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Uwe Poeche <uwe.poeche@siemens.com>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
Apollo Lake seems to start with PCIe root ports unusable/uninitialized
before FspMemoryInit() is called and FSP-M properly initializes these
root ports.
However, we need the root ports accessible before FspMemoryInit() in
certain cases, such as emitting POST codes through a PCIe device.
For the initialization to happen properly, certain register writes
specified in Apollo Lake IAFW BIOS spec, vol. 2 (#559811), chapter
3.3.1 have to be done.
BUG=none
TEST=Boot on siemens/mc_apl2 with NC_FPGA_POST_CODE enabled and check
that the POST codes are emitted before FspMemoryInit().
Change-Id: If782bfdd5f499dd47c085a0a16b4b15832bc040e
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Signed-off-by: Jan Samek <jan.samek@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68223
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add the gma-mainboard.ads for display output definition and enable the
libgfxinit usage in mainboard Kconfig.
Change-Id: I7e7a44736a8136b5320821e744134c7d64c7f1b4
Signed-off-by: Jan Samek <jan.samek@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67683
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Enable early initialization of the PTN3460 DP-to-LVDS bridge on this
board in order to allow showing the bootsplash screen at coreboot
runtime.
Change-Id: Ib1b727cef5fb8bea2d6d6c9896ad0107caeea51a
Signed-off-by: Jan Samek <jan.samek@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67682
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-by: Uwe Poeche <uwe.poeche@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Since there are no legacy devices on the variant mc_apl7 do not wait
for them on mc_apl7.
Change-Id: Ia4e6c0fb495a347be51bd6604a1d9b73098fb7b6
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67684
Reviewed-by: Jan Samek <jan.samek@siemens.com>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
It is highly unlikely that the "OEM revision" of the DSDT is 0x20110725
on mainboards with a chipset not yet released on 2011-07-25. Since this
comment is most likely to have been copy-pasted from other boards, drop
it from boards which use a chipset newer than Sandy/Ivy Bridge.
Change-Id: If2f61d09082806b461878a76b286204ae56bf0eb
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66715
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Tarun Tuli <taruntuli@google.com>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
|
|
These comments don't add much value, so remove them.
Change-Id: I7e9692e3fe82345cb7ddcb11c32841c69768cd36
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66713
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Tarun Tuli <taruntuli@google.com>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
|
|
mc_apl7 does not use security features like VBOOT and TPM.
Test: flash mc_apl4 mainboard and ensure the disabled features via log.
Change-Id: I16683b92deb047208848b69c5aa79dc4212ce930
Signed-off-by: Uwe Poeche <uwe.poeche@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/65284
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
This patch adds a new mainboard variant called mc_apl7 which is based
on mc_apl4. So far only the names have been adjusted with no further
changes. Following commits will introduce the needed changes for this
mainboard variant.
Test: build mc_apl7, flash to mc_apl4 and compare log level 8 output
Change-Id: Ie9f2f5c29d071de442f8f3e3eaf4b3c2a6b8920f
Signed-off-by: Uwe Poeche <uwe.poeche@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/65283
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Hook Up SataPortsEnable to the devicetree. As the default value is 0,
set both [0] and [1] in all mainboards so they aren't affected.
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Change-Id: Ica8cf9484a6e6fe4362eabb8a9a59fcaf97c1bd3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/64524
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
There are two APL specific config switches for RAPL and min. cpu clock
(APL_SKIP_SET_POWER_LIMITS, APL_SET_MIN_CLOCK_RATIO). These switches
could be used in future in other CPU platforms. Move them to common code
instead of having them just for one SOC.
Test: Make sure that the clock ratio (MSR 0x198) and the RAPL settings
(MSR0x610) do not change with this patch applied on mc_apl{1,4,5}
mainboard.
Change-Id: I3d63d1b9b6c96586a3c20bf8c1d8001b1d7c4bed
Signed-off-by: Uwe Poeche <uwe.poeche@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63546
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
Break TPM related Kconfig into the following dimensions:
TPM transport support:
config CRB_TPM
config I2C_TPM
config SPI_TPM
config MEMORY_MAPPED_TPM (new)
TPM brand, not defining any of these is valid, and result in "generic" support:
config TPM_ATMEL (new)
config TPM_GOOGLE (new)
config TPM_GOOGLE_CR50 (new, implies TPM_GOOGLE)
config TPM_GOOGLE_TI50 (new to be used later, implies TPM_GOOGLE)
What protocol the TPM chip supports:
config MAINBOARD_HAS_TPM1
config MAINBOARD_HAS_TPM2
What the user chooses to compile (restricted by the above):
config NO_TPM
config TPM1
config TPM2
The following Kconfigs will be replaced as indicated:
config TPM_CR50 -> TPM_GOOGLE
config MAINBOARD_HAS_CRB_TPM -> CRB_TPM
config MAINBOARD_HAS_I2C_TPM_ATMEL -> I2C_TPM && TPM_ATMEL
config MAINBOARD_HAS_I2C_TPM_CR50 -> I2C_TPM && TPM_GOOGLE
config MAINBOARD_HAS_I2C_TPM_GENERIC -> I2C_TPM && !TPM_GOOGLE && !TPM_ATMEL
config MAINBOARD_HAS_LPC_TPM -> MEMORY_MAPPED_TPM
config MAINBOARD_HAS_SPI_TPM -> SPI_TPM && !TPM_GOOGLE && !TPM_ATMEL
config MAINBOARD_HAS_SPI_TPM_CR50 -> SPI_TPM && TPM_GOOGLE
Signed-off-by: Jes B. Klinke <jbk@chromium.org>
Change-Id: I4656b2b90363b8dfd008dc281ad591862fe2cc9e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63424
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
Shorten define names containing PCI_{DEVICE,VENDOR}_ID_ with
PCI_{DID,VID}_ using the commands below, which also take care of some
spacing issues. An additional clean up of pci_ids.h is done in
CB:61531.
Used commands:
* find -type f -exec sed -i 's/PCI_\([DV]\)\(EVICE\|ENDOR\)_ID_\([_0-9A-Za-z]\{2\}\([_0-9A-Za-z]\{8\}\)*[_0-9A-Za-z]\{0,5\}\)\t/PCI_\1ID_\3\t\t/g'
* find -type f -exec sed -i 's/PCI_\([DV]\)\(EVICE\|ENDOR\)_ID_\([_0-9A-Za-z]*\)/PCI_\1ID_\3/g'
Change-Id: If9027700f53b6d0d3964c26a41a1f9b8f62be178
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39331
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
|
|
On mc_apl2 the external RTC is connected to I2C bus 3. All other I2C bus
devices (16.0, 16.1 and 16.2) have been disabled as they are not used.
While coreboot can handle the case where a PCI device does not have
function 0 enabled but a later one (here function 3), Linux seems to
check for function 0 first and ignores the rest if function 0
is missing. So enable PCI device 16.0 in order to let Linux use 16.3
again.
Test=Boot into Linux and make sure that PCI device 16.0 and 16.3 are
visible and I2C attached RTC works properly.
Change-Id: I55a748b6de8128f4b26b908118feff9f06d3fb7c
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62215
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
The mainboards mc_apl{2,4,5,6} use VBOOT for verification and can be in
a recovery state for different reasons. In this case we still want the
MRC cache to be around to avoid the DRAM retraining on every boot.
This patch enables the Kconfig switch HAS_RECOVERY_MRC_CACHE which makes
the already available MRC recovery region in FMAP useable.
Test=Boot mc_apl2 in recovery mode and make sure the recovery MRC
cache is used.
Change-Id: I2ea4993f05dd87a0e637f55e84b4fc06f5e29ecc
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61827
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
|
|
Aggressive Link Power Management are no longer supported on these
mainboards and must therefore be disabled. This feature can have a
negative impact on the real-time behavior of the systems.
TEST:
- Boot into system software on mc_apl1
Change-Id: I8b08381743018790a20273ea1f61e5b0a56e6015
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61402
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
The `find_resource` function will never return null (will die instead).
In cases where the existing code already accounts for null pointers, it
is better to use `probe_resource` instead, which returns a null pointer
instead of dying.
Change-Id: I329efcb42a444b097794fde4f40acf5ececaea8c
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58910
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Lance Zhao
|
|
Specify the type of the `VARIANT_DIR` Kconfig symbol once instead of
doing so on each and every mainboard.
Change-Id: Iea2f992a59e41e00fec3cdc9d6a13b5f3ab0a437
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56558
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Specify the type of the `FMDFILE` Kconfig symbol once instead of doing
so on each and every mainboard.
Change-Id: I810bd3fe8d42102586db6c2c58b7037a60189257
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56557
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Specify the type of the `DEVICETREE` Kconfig symbol once instead of
doing so on each and every mainboard.
Change-Id: If68f11a5ceaa67a3e8218f89e1138c247ebb9a25
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56555
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Specify the type of the `MAINBOARD_PART_NUMBER` Kconfig symbol once
instead of doing so on each and every mainboard.
Change-Id: I3692f9e82fe90af4d0da1d037018a20aa1b45793
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56554
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Specify the type of the `MAINBOARD_DIR` Kconfig symbol once instead of
doing so on each and every mainboard.
Change-Id: If1cc538b0c4938dac193699897b690e402b3c1e8
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56553
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Use the Kconfig switch PCI_ALLOW_BUS_MASTER_ANY_DEVICE instead of
PCI_ALLOW_BUS_MASTER to enable PCIe bus master bit as requested in
CB:56441 during review.
Change-Id: I433dbae0d9b15e41d1d0750298868341ce3d6b46
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56502
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
|
|
Take Kconfig switch PCI_ALLOW_BUS_MASTER into account and set the PCI
bus master bit for legacy devices only if it is allowed.
Change-Id: I7798a767d528419bb093f301140ab68cc8b9c5ae
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56442
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
|
|
Only I2C controller 3 is used on this mainboard. Disable all other
controllers.
Change-Id: Id06d98787a0574a5b3a8dc2e86858dfcc7154606
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55090
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
|
|
The I2C bus at which the external RTC is attached to is operated at
standard speed (100 kHz) at coreboot runtime. The OS can choose to run it
at fast speed since it uses its own driver and controller setup.
Report additional bus timings for fast mode so that OS can do it right.
Change-Id: I82e11e5dde8ad1047713f105c5a6d020eebf1ffd
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55089
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Already released Linux versions did not have the needed ACPI-extension
in the RTC driver. If the ACPI-Support is enabled for the RTC, this
older Linux will not be able to use this device as it will be claimed by
the PNP-drivers. As there is no way to avoid that an older Linux kernel
meets a newer coreboot in the field, we need to disable the ACPI
support for the RTC for the mc_apl-based mainboards.
Change-Id: I9f9939ba3234dc3654a4ef8a498649453941ebdf
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55004
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Variant mc_apl1 is the only one that uses gpio.c from baseboard. For
this reason, gpio.c is moved from baseboard to mc_apl1.
Change-Id: Ie2ba8181dfe887df9abbbd648f2cbdc6ffc65530
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54945
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
|
|
With commit 405f229689 (soc/intel/*: drop UART pad configuration from
common code) the UART pad configuration was dropped from common SoC
code. Through a second commit 5ff17ed393 (mb/siemens/mc_apl1: do UART
pad configuration at board-level) the UART pad configuration was made
for mc_apl1 baseboard. This change is also needed for all other mc_apl
boards.
Change-Id: If78726d9b141e4e7580cca3267f49c1a5b95d7fa
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54911
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
|
|
All the boards in the patch have a constraint for the I2C bus to operate
on 100 kHz. Provide dedicated values for rise time, fall time and data
hold time on mainboard level to get a proper timing which takes the bus
load into account. Giving these values the driver computes the needed
timings correctly.
TEST=Measure I2C frequency on all boards while coreboot accesses
external RTC and make sure it is 100 kHz.
Change-Id: Iab634190bda5fa2a4fdf2ebaa1e45ac897d84deb
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52721
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I14ec7d6faa20542707a1b6041e1ce358ce4a537a
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50204
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
Change-Id: I6e0f33172fbcecebddfccdf64c22685636a23936
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50524
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
With a new HW revision of this board, the connection of the external RTC
RX6110SA was changed from I2C bus 0 to I2C bus 3.
Change-Id: I10dd44949973ea490b3c7e4ad83d56ce2e566adf
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50391
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
UART pad configuration should not be done in common code, because that
may cause short circuits, when the user sets a wrong UART index. Thus,
add the corresponding pads to the early UART gpio table for the board as
a first step. Common UART pad config code then gets dropped in CB:48829.
Also switch to `bootblock_mainboard_early_init` to configure the pads in
early bootblock before console initialization, to make the console work
as early as possible. The board does not do any other gpio configuration
in bootblock, so this should not influence behaviour in a negative way
(e.g. breaking overrides).
Change-Id: Iac8a6e386b708ae5c4dbf0677bfe05f1358bf8fd
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49442
Tested-by: siemens-bot
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-by: Uwe Poeche <uwe.poeche@siemens.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Objects that are created with acpigen need to be declared
with External () for the generation of dsdt.asl to pass
iasl without errors.
There are some objects that are common to all platforms,
and some that should be declared only conditionally.
Having a top-level ASL helps to achieve this.
Change-Id: Ibaf1ab9941b82f99e5fa857c0c7e4b6192c74330
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49794
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Wim Vervoorn <wvervoorn@eltan.com>
Reviewed-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-by: Christian Walter <christian.walter@9elements.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Until now some FSP-S parameters were configured for Siemens APL
mainboards via the Binary Configuration Tool (BCT). For simplification,
the original APL FSP binary should now be used. For this purpose, the
corresponding FSP-S parameters are set via devicetree, respectively via
mainboard_silicon_init_params accordingly.
The following parameters are affected:
- Disable CPU power states (C-states)
- Set lowest Max Pkg Cstate - PkgC0C1
- Disable PCIe Hot Plug for all enabled RPs
- Disable PCIe Transmitter Half Swing for all RPs
- Disable PCIe Active State Power Management (ASPM) for all RPs
- Disable PCIe L1 Substates for all RPs
TEST:
- Compare old with new coreboot log on mc_apl5, found no differences
- Boot Linux v4.4 and check output of 'lspci'
Change-Id: I5af627defd6426140cc9a74bb18db400a8971d72
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49462
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
Do LPC/eSPI pad configuration at board-level to match other platforms.
Early gpio configuration was done in romstage, while LPC pads were
configured in bootblock. Instead of adding another dedicated gpio table
for bootblock, move early gpio configuration completely to bootblock on
these boards. This won't hurt, since there is no code touching the pads
in between.
The soc code gets dropped in CB:49410.
Change-Id: I2a614afb305036b0581eac8ed6a723a3f80747b3
Tested-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49413
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
|
|
There's one copy of this function for all variants except mc_apl4. Move
one copy into common mainboard.c and exit early if running on mc_apl4.
Change-Id: I4e35b58adc074831ccec433b8e014db0695b955e
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47402
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
A MAC address that is neither 00:00:00:00:00:00 nor ff:ff:ff:ff:ff:ff is
considered valid. Instead of using a temporary buffer and memcmp(), use
a single loop that exits as soon as the MAC cannot possibly be invalid.
Change-Id: I2b15b510092860fbbefd150c9060da38aeb13311
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47405
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-by: Uwe Poeche <uwe.poeche@siemens.com>
|
|
Define and use the MAC_ADDR_LEN macro in place of the `6` magic value.
Change-Id: Icfa2ad9bca6668bea3d84b10f613d01e437ac6a2
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47404
Tested-by: siemens-bot
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
Break down multi-line compound conditions into multiple if-statements,
and leverage `continue` statements to avoid nesting multiple checks.
Change-Id: I5edc279a57e25a0dff1a4b42f0bbc88c0659b476
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47403
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Tested-by: siemens-bot
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Uwe Poeche <uwe.poeche@siemens.com>
|
|
Change-Id: I93e09fc9801f6d32cade351bac0cba82f671acfe
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47400
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Tested-by: siemens-bot
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
|
|
Change-Id: I5a5f4e7067948c5cc7a715a08f7a5a3e9b391191
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45904
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
Enable eMMC with HS200 mode for mc_apl6 mainboard.
TEST: Linux booted and checked with 'lspci'.
Change-Id: Ib760a1a26a92047e8916979ffb5001bcff0a6e45
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45898
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Enable CSE PCI device Bus 0: Device 0x0f: Function 0x00 to let
Intel common cse block code can use this device.
Calling me_read_config32(offset) function from ramstage:
Without this CL :
HECI: Global Reset(Type:1) Command
BUG: me_read_config32 requests hidden 00:0f.0
PCI: dev is NULL!
With this CL :
HECI: Global Reset(Type:1) Command
HECI: Global Reset success!
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Change-Id: I97d221ae52b4b03ecd859d708847ad77fe4bf465
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45469
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
|
|
Use the 96 character limit for pad macros.
Change-Id: I03fd2f9309c04628c46e3473bed280edc57e215c
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44470
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
|
|
GPIO Driver mode is used for configuration interrupt routing for
external devices through GPI. But there is no point in configuring
this for GPO. This patch replaces the PAD_CFG_GPO_GPIO_DRIVER macro
with others that do not set the corresponding bit in the Host Software
Pad Ownership register.
Change-Id: I406a08e526a6c655f38e4c0a355957c98e93881c
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44469
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
|
|
The three Intel Apollo Lake boards (apl_rvp, leafhill and minnow3) do
not define MAX_CPUS, which would then default to 1. Since this is most
likely an oversight, use the same value as other Apollo Lake boards.
To ensure this does not happen again, factor out MAX_CPUS to SoC scope.
Change-Id: I5ed98a6b592c8010b59eca7ff773ae1ccc4cd7b1
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45144
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
APL does not support Hyper-Threading, and has at most four CPU cores.
Change-Id: Ib2ffadc0c31cdd96bec8eed5364c984acb2e1250
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45143
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The common fast SPI driver has a function to set up the SPI OPCODE menu.
Use this function here instead of coding it again as it results in the
very same register values being written.
TEST=Compare register values in both cases and make sure they match.
Change-Id: I98457a0b0652f746734ee4204e10acd09b6e5fda
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43166
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: <uwe.poeche@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I73695152ec8d8ab2dabf8421ef2405f70de0f4ba
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42795
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Kconfig 4.17 started using the $(..) syntax for environment variable
expansion while we want to keep expansion to the build system.
Older Kconfig versions (like ours) simply drop the escapes, not
changing the behavior.
While we could let Kconfig expand some of the variables, that only
splits the handling in two places, making debugging harder and
potentially messing with reproducible builds (e.g. when paths end up
in configs), so escape them all.
Change-Id: Ibc4087fdd76089352bd8dd0edb1351ec79ea4faa
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42481
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-by: Wim Vervoorn <wvervoorn@eltan.com>
|
|
Stefan thinks they don't add value.
Command used:
sed -i -e '/file is part of /d' $(git grep "file is part of " |egrep ":( */\*.*\*/\$|#|;#|-- | *\* )" | cut -d: -f1 |grep -v crossgcc |grep -v gcov | grep -v /elf.h |grep -v nvramtool)
The exceptions are for:
- crossgcc (patch file)
- gcov (imported from gcc)
- elf.h (imported from GNU's libc)
- nvramtool (more complicated header)
The removed lines are:
- fmt.Fprintln(f, "/* This file is part of the coreboot project. */")
-# This file is part of a set of unofficial pre-commit hooks available
-/* This file is part of coreboot */
-# This file is part of msrtool.
-/* This file is part of msrtool. */
- * This file is part of ncurses, designed to be appended after curses.h.in
-/* This file is part of pgtblgen. */
- * This file is part of the coreboot project.
- /* This file is part of the coreboot project. */
-# This file is part of the coreboot project.
-# This file is part of the coreboot project.
-## This file is part of the coreboot project.
--- This file is part of the coreboot project.
-/* This file is part of the coreboot project */
-/* This file is part of the coreboot project. */
-;## This file is part of the coreboot project.
-# This file is part of the coreboot project. It originated in the
- * This file is part of the coreinfo project.
-## This file is part of the coreinfo project.
- * This file is part of the depthcharge project.
-/* This file is part of the depthcharge project. */
-/* This file is part of the ectool project. */
- * This file is part of the GNU C Library.
- * This file is part of the libpayload project.
-## This file is part of the libpayload project.
-/* This file is part of the Linux kernel. */
-## This file is part of the superiotool project.
-/* This file is part of the superiotool project */
-/* This file is part of uio_usbdebug */
Change-Id: I82d872b3b337388c93d5f5bf704e9ee9e53ab3a9
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41194
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This change moves all ACPI table support in coreboot currently living
under arch/x86 into common code to make it architecture
independent. ACPI table generation is not really tied to any
architecture and hence it makes sense to move this to its own
directory.
In order to make it easier to review, this change is being split into
multiple CLs. This is change 3/5 which basically is generated by
running the following command:
$ git grep -iIl "arch/acpi" | xargs sed -i 's/arch\/acpi/acpi\/acpi/g'
BUG=b:155428745
Change-Id: I16b1c45d954d6440fb9db1d3710063a47b582eae
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40938
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
|
|
Done with sed and God Lines. Only done for C-like code for now.
Change-Id: I7b656f0244774cb174a90d97c5ae1c725802b636
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40099
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
|
|
Currently, those who want to use measured boot implemented within
vboot should enable verified boot first, along with sections such
as GBB and RW slots defined with manually written fmd files, even
if they do not actually want to verify anything.
As discussed in CB:34977, measured boot should be decoupled from
verified boot and make them two fully independent options. Crypto
routines necessary for measurement could be reused, and TPM and CRTM
init should be done somewhere other than vboot_logic_executed() if
verified boot is not enabled.
In this revision, only TCPA log is initialized during bootblock.
Before TPM gets set up, digests are not measured into tpm immediately,
but cached in TCPA log, and measured into determined PCRs right after
TPM is up.
This change allows those who do not want to use the verified boot
scheme implemented by vboot as well as its requirement of a more
complex partition scheme designed for chromeos to make use of the
measured boot functionality implemented within vboot library to
measure the boot process.
TODO: Measure MRC Cache somewhere, as MRC Cache has never resided in
CBFS any more, so it cannot be covered by tspi_measure_cbfs_hook().
Change-Id: I1fb376b4a8b98baffaee4d574937797bba1f8aee
Signed-off-by: Bill XIE <persmule@hardenedlinux.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35077
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
They're listed in AUTHORS and often incorrect anyway, for example:
- What's a "Copyright $year-present"?
- Which incarnation of Google (Inc, LLC, ...) is the current
copyright holder?
- People sometimes have their editor auto-add themselves to files even
though they only deleted stuff
- Or they let the editor automatically update the copyright year,
because why not?
- Who is the copyright holder "The coreboot project Authors"?
- Or "Generated Code"?
Sidestep all these issues by simply not putting these notices in
individual files, let's list all copyright holders in AUTHORS instead
and use the git history to deal with the rest.
Change-Id: I18e513cefc373b1cd70d31d1159928cc948a8476
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39609
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: David Hendricks <david.hendricks@gmail.com>
Reviewed-by: Tristan Corrick <tristan@corrick.kiwi>
|
|
Due to build rules, dummy acpi_tables source files were added in many
mainboards. With commit 1e83e5c61a3aa98f58f7d8cbf8d1eb9532896cc3
("src/arch/x86: Build mainboard acpi_tables source if present"),
the build system will build mainboard acpi_tables only if present. Remove
the dummy/empty/blank acpi_tables source files.
BUG=None
TEST=Build test with some google mainboards.
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Change-Id: I0cef34368e2e5f5e3b946b22658ca10c7caad90a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37854
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Wim Vervoorn <wvervoorn@eltan.com>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
|
|
Previously, each Intel chipset had its own sleepstates.asl file.
However, this is no longer the case, so drop these comments.
Change-Id: I50aba6e74f41e2fa498375b5eb6b7e993d06bcac
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37855
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-by: Wim Vervoorn <wvervoorn@eltan.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
It provides no useful information, so it might as well vanish.
Change-Id: I0df6f4639a16058486c2e2d40fe4067d65670731
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37856
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-by: Wim Vervoorn <wvervoorn@eltan.com>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
Change-Id: I5791fddec8b2387df5979adbb1a0fa64c5dd23ea
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37522
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
Kconfig became stricter on what it accepts, so accomodate before
updating to a new release.
Change-Id: I92a9e9bf0d557a7532ba533cd7776c48f2488f91
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37156
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
This patch replaces and cleans up the redundant PTN3460 driver files in
/mainboard/siemens directories by using the now available driver in
src/drivers/i2c/ptn3460 and providing mainboard specific functions to
the driver.
TEST=Display is working on Siemens mainboards (e.g. mc_tcu3, mc_apl1, ...).
Change-Id: I976a502e7176a356bab772758250db3cdff529b9
Signed-off-by: Uwe Poeche <uwe.poeche@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36643
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This mainboard needs VT-d to be enabled. Do so in devicetree.
Change-Id: I9f2f733163be019ac329660d7633b48c5d7896f1
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36749
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
|
|
The TPM chip needs to be added to the devicetree so that the ACPI tables
will be generated for it. These ACPI table entry is used by the OS to get
the location of the TPM chip.
Change-Id: Ic40d1cf236dd849f04f088808d94b6dd81e3238a
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36677
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
|
|
This mainboard variant uses SD-card and not eMMC. Therefore eMMC
controller is disabled while SDHCI is enabled.
Change-Id: I40b314905730b5d74c674d2251f8a4e5c807805f
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36676
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
On this mainboard variant the PCIe-2-PCI bridge is used a bit different.
Adjust the switched off clock lines to match the mainboard
configuration.
Change-Id: I16f3b6eed0948c8201baecdfbb8052c6c1c335c8
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36671
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
|
|
mc_apl6 uses VBOOT scheme so enable it as default.
Change-Id: I341180f3815ff9f3b2db801d9d989119a2585b03
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36669
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
|
|
This patch adds a new mainboard variant called mc_apl6 which is based
on mc_apl3. So far only the names have been adjusted with no further
changes. Following commits will introduce the needed changes for this
mainboard variant.
Change-Id: Ic935f6cc1f037947b2c167696d40da8309e4d4f0
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36668
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
|
|
This patch creates a common instance of sleepstates.asl inside intel common
code (southbridge/intel/common/acpi) and asks all IA CPU/SOC code to
refer sleepstates.asl from common code block.
TEST=Able to build and boot Hatch and ICL DE system. Dump DSDT.asl to verify
S0/S3/S4/S5 entries after booting to OS.
Change-Id: Ie2132189f91211df74f8b5546da63ded4fdf687a
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36463
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
As fmaptool can now handle the offset computation for every mentioned
region in the fmap file on its own there is no need to provide the
offset in the fmd file anymore. This patch clears this out so that the
files are way more readable now.
Change-Id: I1dc841604fdb662e08cb6690ff4bf6dd311e01d8
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36234
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
|
