| Age | Commit message (Collapse) | Author |
|---|
|
Change strcpy to strncpy just to be safe.
Found-by: Coverity Scan #1446759
Signed-off-by: Martin Roth <gaumless@gmail.com>
Change-Id: I7ed094a313692806a6ab6b4226b9978647e9cb8d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78621
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
By calling get_board_settings() when board_cfg is initialized, board_cfg
is guaranteed not to be NULL, so don't check to see if it's NULL.
Found-by: Coverity Scan #1513079
Signed-off-by: Martin Roth <gaumless@gmail.com>
Change-Id: I61105be9ed71ff30efdda66d2cbfcaf54d70053f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78618
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
Selects should be done in the Kconfig file instead of Kconfig.name and
not mixed over both files.
Change-Id: Iface0fd1d44649c6d9773940818e028e3d3a4292
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75029
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
|
|
VMX is enabled through a bit in the IA32_FEATURE_CONTROL MSR, which can
be locked. The MSR remains locked after a non-power cycle reset, though.
If the MSR is locked, coreboot bails out and leaves VMX in the state it
was found. Because of this, changes to the VMX enable option in the BMC
only take effect after the system is power cycled.
This behaviour is highly undesirable because users are likely not aware
that a power cycle is required for changes to VMX state to take effect.
So, if VMX is supported, the IA32_FEATURE_CONTROL MSR is locked and the
current VMX state does not match the requested state, then issue a full
reset. This will power cycle the system and unlock the MSR, so that the
desired VMX state can be programmed into the MSR. This is checked early
to avoid needlessly doing time-consuming operations (running FSP) twice
if we know we will need to power cycle the system anyway.
Note that a user may change the VMX setting after the newly-added check
but before the setting is read in ramstage to program the MSR, but this
is a non-issue as firmware settings need a reset to take effect anyway.
TEST: Toggle VMX setting in BMC and reboot without power cycle, observe
coreboot automatically issues a power cycle reset because the MSR
is locked and the VMX state differs. Verify that the system boots
properly with VMX in the correct state after having power cycled.
Change-Id: Id9061ba896a7062da45a86fb26eeb58927184dcb
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75141
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
|
|
The `get_board_settings()` function always returns non-NULL, so there is
no need for NULL checks. When only one member is accessed, also drop the
local variable and directly dereference the function's return value.
Change-Id: I4fc62ca2454f4da7c8ade506064a7b0e6ba48749
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75140
Reviewed-by: Christian Walter <christian.walter@9elements.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
|
|
Hook up the `wake_on_usb` EEPROM setting so that it works as intended.
TEST=Keysmash on a USB keyboard, verify Hermes does not wake from S3.
Change-Id: I81531b90abae6a62754ea66c47e934e1f440bda2
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/72906
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Found-by: linter
Change-Id: I7c6d0887a45fdb4b6de294770a7fdd5545a9479b
Signed-off-by: Alexander Goncharov <chat@joursoir.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/72795
Reviewed-by: Nicholas Chin <nic.c3.14@gmail.com>
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Erik van den Bogaert <ebogaert@eltan.com>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The parallel mp code picks up lapics at runtime, so remove it from all
devicetrees that use this codebase.
Change-Id: I5258a769c0f0ee4bbc4facc19737eed187b68c73
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69303
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
<gpio.h> chain-include <soc/gpio.h>.
Change-Id: Ia57d5cd33c70b6a755babd4db56c64c0e3666f9f
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/71817
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Change-Id: I2a6947c1a39b115a7c7f5da1c9becfd51f45fad9
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69239
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Also sort includes.
Change-Id: Iccb7f28a2c913ae0983bf224a03610d7fdd13c68
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69030
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Configure the Intel iGPU as primary video adapter if enabled according
to EEPROM settings. The default is to use the ASPEED BMC as primary
video adapter, which only has a VGA output and the remote KVM output.
For now, use the FSP GOP driver to light up the iGPU. There are several
issues with libgfxinit on the Hermes, probably due to the unusual setup
of the iGPU's display outputs. They are routed to a mezzanine connector
for a piggy-back sub-board, of which there are two models. The Poseidon
piggy-back has two DisplayPort outputs and an HDMI output coming from a
MegaChips LSPCON. The Avalanche piggy-back routes all three DisplayPort
outputs from the iGPU into a FPGA, which acts as a DisplayPort sink.
Note that the FSP GOP only initializes at most 2 iGPU display outputs.
However, all three outputs function properly once OS (Windows, Linux)
graphics drivers take over.
Additionally, update the config file that Prodrive uses to build
coreboot images so that the iGPU can be used as primary.
TEST=Verify that the iGPU's outputs work properly in pre-OS, Windows and
Linux, on both the Poseidon and Avalanche piggy-backs.
Change-Id: I24d9ebc2055dc246e7f257aa2f3853b22c8af370
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62649
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Strings in C are highly cursed. Use `snprintf()` to minimize the
potential of running into undefined behavior in the future.
Change-Id: I3caef25bc7676ac84bb1c40efe6d16f50f8f4d26
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68323
Reviewed-by: Patrick Georgi <patrick@coreboot.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
|
|
The `eeprom_read_serial()` function could return a non-NULL terminated
string if the serial in EEPROM has `HERMES_SN_PN_LENGTH` (32) non-NULL
characters. Make this impossible by adding an additional character for
a NULL byte in the static buffer, which always gets set to 0 (NULL).
Change-Id: I306fe1b6dd3836156afca786e352d2a7dca0d77c
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68322
Reviewed-by: Patrick Georgi <patrick@coreboot.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
|
|
First of all, make sure that `get_board_settings()` never returns NULL.
If there's a problem, return predefined values for board settings.
If the board settings definition differs between coreboot and the BMC,
the CRC will not match. Allow coreboot to use the BMC settings provided
by older BMC firmware revisions which have less settings, if the CRC of
the first N bytes matches the expected CRC.
TEST=Boot coreboot master with BMC FW R04.05, observe board settings
being honored even though coreboot's definition has an extra option.
Change-Id: I0f009b21ef0850a2af6edef1818c770171358314
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67381
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Write the value for reset cause registers to the EEPROM for debugging.
Change-Id: I827f38731fd868aac72103957e01aac8263f1cd3
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67483
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Adjust the EEPROM layout to account for two new fields: board part
number and product part number. In addition, put them in a Type 11
SMBIOS table (OEM Strings). Also, rename a macro to better reflect
its purpose.
Change-Id: I26c17ab37859c3306fe72c3f0cdc1d3787b48157
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67759
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add the `eeprom_read_serial()` function to read serials from the EEPROM.
Note that there's only one buffer now: this means only one serial can be
accessed at the same time, and the buffer needs to be cleared so that it
does not contain old data from other serials. Given that the serials are
copied one at a time into SMBIOS tables, having one shared buffer is not
a problem.
Change-Id: I5c9781e4e599043be756514cfd6dd86dedcf580c
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67275
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The PCH's SGPIO pads are connected to a buffer chip that is powered from
the always-on +3V3_AUX rail. For some cursed reason, when the SGPIO pads
stay configured as SGPIO when a Poseidon system shuts down, voltage from
the +3V3_AUX-powered buffer chip will leak into the +5V rail through the
SATA backplane. Just pulling the SGPIO pads low before the system powers
off stops the +5V rail from being cross-powered.
This issue has only been observed in S5, but it's very likely other
sleep states are affected as well. Thus, always pull the SGPIO pins
low before entering ACPI S3 or deeper because the power supply will
turn off in these states as well.
TEST=Obtain a Poseidon system, verify that the +5V rail is cross-powered
after going to S5. We measured 0.17V on our system, but voltages as
high as 0.6V were measured on other systems. Verify that unplugging
the SGPIO cable going to the SATA backplane results in the +5V rail
voltage dropping to 0V, which indicates that the voltage leakage is
exclusively coming from the SGPIO and SATA backplane. Finally, make
sure that the +5V rail voltage drops to 0V after going into ACPI S5
with this patch applied and the SGPIO cable connected.
Change-Id: Ic872903d5fcdd1c17e02b4c06d5ba29889fbc27d
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/66616
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
|
|
use is_enabled_cpu() on cycles over device list to check
whether the current device is enabled cpu.
TEST: compile test and qemu run successfully with coreinfo
payload
Signed-off-by: Fabio Aiuto <fabioaiuto83@gmail.com>
Change-Id: If64bd18f006b6f5fecef4f606c1df7d3a4d42883
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67797
Reviewed-by: Tim Wawrzynczak <inforichland@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
This reverts commit d6695626631a86d9613ea7c34ff0e898fbfa443c.
Reason for revert: Was submitted out-of-order and with an unresolved
TODO in the commit message.
Change-Id: Id5a8770226afbfcdf63d451157e4586b6cdd5189
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67284
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-by: Sean Rhodes <sean@starlabs.systems>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Adjust the EEPROM layout to account for two new fields: board part
number and product part number. In addition, put them in a Type 11
SMBIOS table (OEM Strings).
TODO: This currently stores the "raw" part numbers, should we add a
prefix to the SMBIOS strings?
Change-Id: I85fb9dc75f231004ccce2a55ebd9d7a4867fcb93
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67276
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
There's no reason to use camel case for EEPROM region names or local
variables. Use snake case for consistency with coreboot's code style.
Change-Id: Id1200a0c778095b109d824a1ca4e3e69591e4165
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/67274
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Reviewed-by: Christian Walter <christian.walter@9elements.com>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
|
|
Set the default value for MAX_CPUS in the SoC config and drop it from
the mainboards where it is set to those values.
Change-Id: Ib56fdcfe770ef736a2c5e183481d9f9966570e6d
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52607
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Introduce a new field in the board settings EEPROM region to control
whether BIOS menu is to be enabled. This field will be used in EDK2
payload.
Signed-off-by: Lean Sheng Tan <sheng.tan@9elements.com>
Change-Id: I0af81c9e70a0088caea6bc7e2b81eab9a123c0f7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/65128
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Christian Walter <christian.walter@9elements.com>
|
|
Break TPM related Kconfig into the following dimensions:
TPM transport support:
config CRB_TPM
config I2C_TPM
config SPI_TPM
config MEMORY_MAPPED_TPM (new)
TPM brand, not defining any of these is valid, and result in "generic" support:
config TPM_ATMEL (new)
config TPM_GOOGLE (new)
config TPM_GOOGLE_CR50 (new, implies TPM_GOOGLE)
config TPM_GOOGLE_TI50 (new to be used later, implies TPM_GOOGLE)
What protocol the TPM chip supports:
config MAINBOARD_HAS_TPM1
config MAINBOARD_HAS_TPM2
What the user chooses to compile (restricted by the above):
config NO_TPM
config TPM1
config TPM2
The following Kconfigs will be replaced as indicated:
config TPM_CR50 -> TPM_GOOGLE
config MAINBOARD_HAS_CRB_TPM -> CRB_TPM
config MAINBOARD_HAS_I2C_TPM_ATMEL -> I2C_TPM && TPM_ATMEL
config MAINBOARD_HAS_I2C_TPM_CR50 -> I2C_TPM && TPM_GOOGLE
config MAINBOARD_HAS_I2C_TPM_GENERIC -> I2C_TPM && !TPM_GOOGLE && !TPM_ATMEL
config MAINBOARD_HAS_LPC_TPM -> MEMORY_MAPPED_TPM
config MAINBOARD_HAS_SPI_TPM -> SPI_TPM && !TPM_GOOGLE && !TPM_ATMEL
config MAINBOARD_HAS_SPI_TPM_CR50 -> SPI_TPM && TPM_GOOGLE
Signed-off-by: Jes B. Klinke <jbk@chromium.org>
Change-Id: I4656b2b90363b8dfd008dc281ad591862fe2cc9e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63424
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
Shorten define names containing PCI_{DEVICE,VENDOR}_ID_ with
PCI_{DID,VID}_ using the commands below, which also take care of some
spacing issues. An additional clean up of pci_ids.h is done in
CB:61531.
Used commands:
* find -type f -exec sed -i 's/PCI_\([DV]\)\(EVICE\|ENDOR\)_ID_\([_0-9A-Za-z]\{2\}\([_0-9A-Za-z]\{8\}\)*[_0-9A-Za-z]\{0,5\}\)\t/PCI_\1ID_\3\t\t/g'
* find -type f -exec sed -i 's/PCI_\([DV]\)\(EVICE\|ENDOR\)_ID_\([_0-9A-Za-z]*\)/PCI_\1ID_\3/g'
Change-Id: If9027700f53b6d0d3964c26a41a1f9b8f62be178
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39331
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
|
|
Introduce a new field in the board settings EEPROM region to control
whether VT-x is to be enabled.
Change-Id: If65c58dd6e5069dba1675ad875c7ac89e704350e
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61507
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Marvin Drees <marvin.drees@9elements.com>
|
|
Run the command below to fix all occurrences.
$ git grep -l 'configuration in bootblock\. \*/' | xargs sed -i 's,configuration in bootblock\. \*/,configuration in bootblock */,'
Change-Id: I84669341e2c8976953284dbaf113da3397857de3
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/60248
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
All Coffee Lake mainboards use the default value for the setting
`SataMode`. Thus, drop it from their devicetree.
Change-Id: Ibb329eb8b752c2220bb25f14fb6ae92dd8a308d6
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59889
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The Hermes mainboard is used in different system configurations. The
current VBT for Poseidon systems is unsuitable for Avalanche systems
because display ports are connected differently.
Add a new field in the BMC config EEPROM layout and use it to choose
the correct VBT for every system configuration.
Change-Id: I2647f2ae3f496b9ad75980ba86beb7800fdb0668
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59838
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
The original RCOMP resistor and target values only apply to ULT CPUs and
do not make sense for the CFL-S CPUs Hermes uses. Fix the RCOMP settings
and the associated comments.
Tested, still boots.
Change-Id: I015797c58c914c6581d472e6d70d2dd7bad2b14f
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58364
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Define a new field in the board config EEPROM layout for port B Vref.
Write port B Vref settings to unused non-volatile NID 0x12 instead of
NID 0x18, the actual port B NID. Because per-port Vref settings don't
persist after codec resets, a custom Realtek driver (ab)uses NID 0x12
to restore port B Vref after resetting the codec.
Change-Id: Iaa11ba9c74f643e94046d4983fbce65dbedd1025
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58879
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Update the pin configs for the front panel jacks.
Change-Id: I3760f0a25e964cf0eba99d180fd6f3e8488af868
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59545
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Use lowercase for hex numbers, sort includes alphabetically and avoid
relying on indirect inclusion. Include `<intelblocks/gpio.h>` instead
of `<intelblocks/gpio_defs.h>`, as the latter implcitly relies on one
definition from `<soc/gpio.h>`. Also drop useless dsdt.asl and fix up
the indentation of some includes.
Tested with BUILD_TIMELESS=1, Prodrive Hermes remains identical.
Change-Id: I3aeb9a644cf33cb4b1987174f40ef0fc7daccfa9
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59672
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
There's no need to use a variant structure here. Only one variant is
used, and revision-specific differences are handled at run-time, and
it's unlikely that another variant will ever exist.
Reorganize the mainboard code to get rid of the variant structure.
Change-Id: I1543f5b76975b0e7183fbb759e9bae5c34151d06
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59671
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Change-Id: I943d0e2a91778df306f323e2b889cd4e928e0c2b
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59837
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
The Prodrive Hermes mainboard has four i211 Ethernet NICs and an i210
Ethernet NIC, but their numbering isn't consistent with the PCIe root
port function numbers. With only a M.2 SSD plugged in, Linux uses the
following names:
PHY 0 ---> enp6s0
PHY 1 ---> enp4s0
PHY 2 ---> enp3s0
PHY 3 ---> enp1s0
PHY 4 ---> enp2s0
These names change after adding or removing PCIe devices in slots
connected to root ports that get enumerated before the NICs' root
ports, because the assignment of secondary bus numbers depends on
the enumeration order. Because of this, the "predictable" network
interface names are not at all predictable, which is awful.
To avoid this, describe the NICs using SMBIOS Type41 entries with the
correct instance numbers. With this patch, Linux uses these names:
PHY 0 ---> eno0
PHY 1 ---> eno1
PHY 2 ---> eno2
PHY 3 ---> eno3
PHY 4 ---> eno4
No matter what PCIe devices are present, these names don't change.
Change-Id: I7a527298f84172f9135006083ad7e748dcc27911
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58628
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The "internal audio connection" setting is actually about the front
panel audio. Rename functions and variables to reflect this.
Change-Id: I1be8f68ac3e8b91bc4983dc06daa37afb7bdf926
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58904
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Justin van Son <justin.van.son@prodrive-technologies.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Set the `PcieRpLtrEnable` option to enable the LTR capability on all PCH
PCIe root ports.
TEST=Verify LTR capability enabled in `DevCap2` using `lspci -vv`
Change-Id: I07ea37d178ea61d904c4f131fdea31479e899ef3
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58326
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Map each PCIe clock source to the corresponding root port. Also, correct
the CLKREQ# mapping for clock sources not associated to any CLKREQ# pin.
The default `PcieClkSrcClkReq` value of 0 corresponds to CLKREQ# 0.
TEST=Check that Linux sees the same PCIe devices with this commit:
- All 5 onboard Ethernet NICs
- BMC
- Two random graphics cards in PEG0 and PEG1 slots
- M.2 M NVMe SSD
Change-Id: I0515877a36d42fb8858a0f0b3c0af1199a18d9af
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58368
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Correct the PCIe clock source configuration as per the schematics.
Apparently, FSP does not turn off unused PCIe clock sources when using
SPS (Server Platform Services) firmware, but it does when using CSME
firmware.
TEST=BMC and Ethernet NICs get detected when using CSME firmware.
Change-Id: Id25a34816f512510640db95251a7a792c1eebe62
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58065
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
There's no need to have an overridetree with a single board variant.
TEST=Compare static.c and observe only device order has changed.
Change-Id: I2097e247c27d5d0c5479cb533b477cd490a4c827
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58367
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Move per-port PCIe settings inside the corresponding PCIe root port
device. Also, remove several unnecessary and/or redundant comments.
Tested with BUILD_TIMELESS=1, Prodrive Hermes remains identical.
Change-Id: I3f64d56b3b2c592194b18ae7b7c63ef41a1e060f
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58325
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Enable SATA power optimizer as recommended by Intel. Tested, a SATA SSD
is still detected correctly by SeaBIOS (version 1.14.1).
Change-Id: Ia6d29de08583dfc0c2d38e8395adcaa2c540ec7b
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57834
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Fixes commit bd5b4aa683a634a73a6a63d1f197e2bb74b6a80e
"soc/intel/cannonlake: Switch PMC to use device callbacks" as it
requires the PCI device 1f.2 to be present in the devicetree.
It was missing for this mainboard and caused a boot failure.
Change-Id: Iaf508b2d955578efa2a266af50c568f5c0a47aaf
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57574
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
SoC code already sets this UPD to `CONFIG_IED_REGION_SIZE`, which
defaults to 0x400000 for soc/intel/cannonlake.
Change-Id: I6587e17a4a3425c561cffe6e3df0d932a2458168
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57260
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
|
|
Change-Id: I291dc71bb6e3888b71ebce315f9ad09ccbc4a9a7
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57259
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
|
|
Since all mainboards use `CHIPSET_LOCKDOWN_COREBOOT`, make it the
default by changing its enum value to 0 and remove its configuration
from all related devicetrees.
If `common_soc_config.chipset_lockdown` is not configured with
something else in the devicetree, then `CHIPSET_LOCKDOWN_COREBOOT`
is used.
Also, add a release note for the upcoming 4.15 release.
Change-Id: I369f01d3da2e901e2fb57f2c83bd07380f3946a6
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56967
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Tim Crawford <tcrawford@system76.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
|
|
Tested on prodrive/hermes.
Change-Id: I72be8bde59d9eb0c1eff8c65dc734c6805732e09
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56086
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: <wouter.eckhardt@prodrive-technologies.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Specify the type of the `VARIANT_DIR` Kconfig symbol once instead of
doing so on each and every mainboard.
Change-Id: Iea2f992a59e41e00fec3cdc9d6a13b5f3ab0a437
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56558
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Specify the type of the `OVERRIDE_DEVICETREE` Kconfig symbol once
instead of doing so on each and every mainboard.
Change-Id: I4cbf4e318a30f0cf75aa8690e7454b9caa115c9d
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56556
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Specify the type of the `MAINBOARD_PART_NUMBER` Kconfig symbol once
instead of doing so on each and every mainboard.
Change-Id: I3692f9e82fe90af4d0da1d037018a20aa1b45793
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56554
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Specify the type of the `MAINBOARD_DIR` Kconfig symbol once instead of
doing so on each and every mainboard.
Change-Id: If1cc538b0c4938dac193699897b690e402b3c1e8
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56553
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
There's no need to specify the type of the `CBFS_SIZE` Kconfig symbol
more than once. This is done in `src/Kconfig`, along with its prompt.
Change-Id: I9e08e23e24e372e60c32ae8cd7387ddd4b618ddc
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56552
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Return the HSI version read from BMC in smbios_mainboard_version.
Change-Id: If907d598c9e05d35f8898d294678f61d075f935a
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55712
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
The BMC EEPROM layout has been updated to contain system and mainboard
serial numbers. Use these values in SMBIOS Type 1 and Type 2 tables.
Change-Id: I55b51a856b4ad28fd56b02015b2e1d49cd629735
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55275
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I84b9ef080f1ac91ea6f7273457b882677abf70d3
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52885
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The `write_offset` parameter is always zero. Remove it.
Change-Id: Ib63cb25904ad6c1c7424a9c01d8bf1e84c08453b
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52884
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Hermes can be used with either CSME or SPS firmware. However, the SPS
(Server Platform Services) firmware does not support ACPI S3 and S4
sleep states, and coreboot should not report S3 and S4 as supported.
Add a Kconfig option to be selected when building coreboot to use with
SPS firmware, which allows disabling ACPI S3 and S4 sleep state support.
Change-Id: I9d0fa8530e198e86415f92da6719d2fb0d2401ec
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54058
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
|
|
Drop Vref verbs from the baseboard table as it's not required for
Rev. 3 and earlier.
Change-Id: I41c207f97dad6c9107c1999eb46d2d6304a6c217
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51919
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Christian Walter <christian.walter@9elements.com>
|
|
All related mainboards are setting DIMM_SPD_SIZE to 512. Therefore,
default to 512 in the SoC Kconfig and drop it from related mainboard
Kconfigs.
Change-Id: Idb6a0e42961eeb490afd76b4aa7d940961991733
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52513
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Fix board ID (HSI) read from BMC:
* R02 and R03 have an HSI of 2.
* R04 has an HSI of 3.
Change-Id: I987b2dd848c48e3562bcc07270c958cde3c5a962
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51920
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
MPTS is currently not executed by the AML interpreter.
Use Method (\\_SB.MPTS) instead of
Scope (\\_SB)
Method (MPTS)
ScopeEnd
Tested on Prodrive Hermes. MPTS is now executed at S5.
Change-Id: I9074eb4ba55aab3f9a47ae5e3c3ddd338406a5e4
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52382
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: <wouter.eckhardt@prodrive-technologies.com>
|
|
The logic for bytes to copy to the function input pointer was wrong.
What it did was to loop over all 2 bytes that need to be read and only
copy the first byte.
Change-Id: Ic08cf01d800babd4a9176dfb2337411b789040f3
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52207
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Christian Walter <christian.walter@9elements.com>
|
|
To pack a struct, the `__packed` attribute must come after the `struct`
keyword. Moreover, unions cannot be packed (structs inside unions can,
though). Correct uses of `__packed` so that EEPROM structs get packed.
Change-Id: I39d2c9ebc370605d5623b134189aa95a074ec7c3
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51980
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: <wouter.eckhardt@prodrive-technologies.com>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
|
|
If the board settings aren't valid, Port E uses the settings for earlier
board revisions, which is undesired. Disable Port E by default on R04+.
Change-Id: I03bd50b915a2120283b77179debaa735bb7ef027
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51529
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Christian Walter <christian.walter@9elements.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Already selected by SoC.
Change-Id: I1d941881f50350b6b581416a2e722ea2e7485a1c
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50791
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Christian Walter <christian.walter@9elements.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Use different verb tables depending on board revision.
For board revision R03 and older use the existing verb tables.
For revisions newer than R03 use the new verb tables and also
apply the dynamic audio configuration recently added.
Also do the following:
* Use correct NID port mapping
* Fix verb count in ALC888 header
* Fix NID in Intel codec verbs
Change-Id: I24ea9149eb2cddb815ff82744a351c926a94aaef
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44772
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
As one option is consumed by MPinit, update the soc config even earlier.
Tested on Prodrive hermes:
Turbo can be disabled and cores won't exceed their base frequency.
Change-Id: I9f444c3b91d2ee1a613ebac1922f1e6b60363c0b
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50798
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Will be used to determine the board revision.
Change-Id: I41e4c6ad83e23c9d79e6abab3f38ad46bd3bec06
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50788
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add settings describing the BMC.
Will be used by the following patch to read the board revision.
Change-Id: If464138fc1bdf02a45a21f638b179048d68d974d
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50787
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The I2C EEPROM on SMBUS needs to be updated with the current board
layout, so that the BMC knows the actual configuration.
Collect all needed information and update the EEPROM if something
changed. Every byte written add a delay of 5 msec.
Change-Id: Ic8485e6c700eede75b1e829238ee70da65118ace
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48810
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
|
|
Found using:
diff <(git grep -l '#include <string.h>' -- src/) <(git grep -l 'STRINGIFY\|memcpy\|memmove\|memset\|memcmp\|memchr\|strdup\|strconcat\|strnlen\|strlen\|strchr\|strncpy\|strcpy\|strcmp\|strncmp\|strspn\|strcspn\|strstr\|strtok_r\|strtok\|atol\|strrchr\|skip_atoi\|snprintf' -- src/)|grep '<'
Change-Id: Id2aa085a4762355d9fb1628df40f7b43fbc81fc0
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50687
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
* Check and print errors returned from reading from I2C
* Rework offset calculation by using more macros
* Get rid of stage-specific preprocessor code
* Define the EEPROM layout as struct
* Make use of the defined EEPROM layout to calculate offsets
* Read the UPD to disable VT-d from EEPROM
Change-Id: Iad77811318c7dfd3a3a4f8d523cfa0f457f168b6
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48808
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Configure Port C VREF according to the settings in the EEPROM.
Change-Id: I5b4f0d91fc30c6b585434b9450544281f4411ff4
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50396
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Implement `mainboard_azalia_program_runtime_verbs` to configure the
Realtek ALC888 codec according to the settings in the EEPROM. The
encoding of the `internal_audio_connection` field is:
0: Disabled
1: Front HP out
2: Internal speaker
Change-Id: I5e0013217838888977aaa9259e0cfb78c82f719f
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50389
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
|
|
Change-Id: I13c2ece729128fe245de88c0d36ce7b4bcaf6b6d
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50381
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
The reset GPIOs are already configured in bootblock.
Drop the unused ramstage code.
Change-Id: Ic99fcae2a3f00be7eebd7be618df838522dac69f
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50380
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Cache the board settings in memory to avoid having to read them from the
EEPROM multiple times. For now, configure the following settings:
- DeepSx
- USB power in S5
- Power state after G3
Change-Id: Id88529a0b064c54fdf341de3856a8877109d4b14
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48807
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
|
|
Hermes has an EEPROM with firmware configuration data. Add definitions
to read and verify the `board settings` from the EEPROM. Subsequent
commits will hook up these EEPROM settings.
Change-Id: Id86632192ae53fd6b0e4df5b26b5a0a81e972818
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48806
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
|
|
Objects that are created with acpigen need to be declared
with External () for the generation of dsdt.asl to pass
iasl without errors.
There are some objects that are common to all platforms,
and some that should be declared only conditionally.
Having a top-level ASL helps to achieve this.
Change-Id: Ibaf1ab9941b82f99e5fa857c0c7e4b6192c74330
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49794
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Wim Vervoorn <wvervoorn@eltan.com>
Reviewed-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-by: Christian Walter <christian.walter@9elements.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
The PMC doesn't response any more due to invalid CNVi GPIO
configuration. This caused a 30 second boot delay in FSP-S.
Use the same values as FSP-S does. Always disable external I2S BT
audio and use NF3 for pad GPP_D5 and GPP_D6.
Tested on Prodrive hermes:
No boot delay can be observed any more.
Change-Id: I6f4a954786ec21512b0dce908d333952e96de048
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49678
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-by: Christian Walter <christian.walter@9elements.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
UART pad configuration should not be done in common code, because that
may cause short circuits, when the user sets a wrong UART index. Thus,
add the corresponding pads to the early UART gpio table for the board as
a first step. Common UART pad config code then gets dropped in CB:48829.
Change-Id: I5b99a66fb64683f3647ebff3ab01ceb52058f79c
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49440
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
|
|
Only one EEPROM is used to store the board settings, and its I2C address
is constant. Thus, there's no need to pass its address as a parameter.
In addition, reduce the scope of the `I2C_ADDR_EEPROM` definition, since
using it outside of eeprom.c would bypass the API's abstraction layer.
Change-Id: I958304e6ed6df05af923139d44ff4fd1de204738
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46565
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
|
|
Drop chipset register definitions in mainboard code in favor of existing
definitions in a header. These definitions are not mainboard-specific.
Tested with BUILD_TIMELESS=1, Prodrive Hermes remains identical.
Change-Id: I29d6f35ec27bff43cf52ae697e905b6a7b48a8d1
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48805
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
|
|
Test results show that USB signals look better with these settings.
Yes, there's a macro in the devicetree now. All ports use the same
settings except for the overcurrent pin, so this avoids redundancy.
Change-Id: Ib0dafab88d8dcc05388b724f6a7183c13ac64934
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48694
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I75f83bcc6c65a048e87f7295a66526eb384afc5d
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48692
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Use FSPS_UPD instead of FSP_S_CONFIG as argument as already done on
xeon_sp and denverton_ns. This allows to set test config UPDs from
mainboard code as well.
Change-Id: I6d67264e22df32b9210ce88b99d6a7a4f6b97ffb
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48644
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
|
|
* Drop PcieRpSlotImplemented on internal slots
* Add PCIe port 15 that connected to CNVi/M.2 E
Change-Id: Iaa05affa760b447fc1725e674b12366684a63720
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47239
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Christian Walter <christian.walter@9elements.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Allow to specify which signature is to be checked.
Change-Id: Ica874b1c4283fdb8dbd702c34ccb3315a2cf160d
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48147
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
This allows dropping ugly preprocessor usage from this file.
Change-Id: Idb66d295129d98725f38d11ac162978418bd94c2
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47959
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Having variants' gpio.c call the `gpio_configure_pads` function results
in an API that does not need to pass data around, which is much simpler.
Change-Id: I1064dc6258561bcf83f0e249d65b823368cf0d31
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47958
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
|
|
Most of the existing comments are C-style already.
Change-Id: I9ca4779f5b0560320e9bce4f33e54766522689f9
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47957
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
|
|
The option `HeciEnabled` was partly replaced by use of the device on/off
state in the devicetree in commit 3de90d1. The option has been removed
from the corresponding boards, so `HeciEnabled` is always 0 and ME
always gets disabled during soc finalize, when `HECI_DISABLE_USING_SMM`
is set.
Replace the option in the finalize function by the same dt state check
that sets the FSP option and drop the remaints of `HeciEnabled`.
Devicetrees still having `HeciEnabled` have been adapted to keep the
current behaviour.
Change-Id: Ib4cca9099b9aa3434552a41fbafca7cf6a0dd0eb
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47195
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
InternalGfx isn't used so drop it.
Change-Id: I12f424d8d883e065ef8d007e56a8bff41a7fae53
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47176
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Prevent early throttling when the ambient temperature is high.
Change-Id: Ie6881c9c0942aae3e43509170352271a74244d42
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47094
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
This change reorganizes the CNVi device entries in mainboard
devicetree/overridetree and SoC chipset tree to make it consistent
with how other SoC internal PCI devices are represented i.e. without a
chip driver around the SoC controller itself.
Before:
chip drivers/wifi/generic
register "wake" = "..."
device pci xx.y on end
end
After:
device pci xx.y on
chip drivers/wifi/generic
register "wake" = "..."
device generic 0 on end
end
end
Change-Id: I22660047a3afd5994400341de0ca461bbc0634e2
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46865
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
The dt option `speed_shift_enable` is obsolete now. Drop it.
Change-Id: I5ac3b8efe37aedd442962234478fcdce675bf105
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46462
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
|
|
Get rid of legacy pad macros by replacing them with their newer
equivalents.
TEST: TIMELESS-built board images match
Change-Id: I078f9bb3c78f642afc6dcfd64d77be823a4485c2
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46567
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
