| Age | Commit message (Collapse) | Author |
|---|
|
ALC5682I-VS will use in next build.
BUG=b:194367025
TEST=none.
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I34d736fe1c39860443dac07435a21ccd0ee2f21c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59412
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Enable Acoustic noise mitigation for bugzzy and set slew rate to 1/8
which is calibrated value for the board.
BUG=b:207046230
BRANCH=dedede
TEST=build firmware to UPD and Acoustic noise test
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.corp-partner.google.com>
Change-Id: Id249a143efb9bce70f48fb466fed42e766a10937
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59480
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
If a USB_MUX_EVENT happens while the AP is in S3 during powerdown
transtion (S0->S3->S5), this will cause the device to boot again after
it has finished sequencing down to S5. Since S3 is not POR for ChromeOS
devices anymore, change this event to wake from S3 and S0ix to just
S0ix.
BUG=b:206867635
TEST=emerge-brya coreboot
Signed-off-by: Joey Peng <joey.peng@lcfc.corp-partner.google.com>
Change-Id: Icdab40b6a845a34246d7da336f43e970f7908301
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59411
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
as doc #632048, there is a fix in MRC for this sighting but DdrMemoryDown need to be set to 1.
BUG=b:192478111
BRANCH=volteer
TEST=FW_NAME=chronicler emerge-volteer coreboot chromeos-bootimage
Signed-off-by: Sheng-Liang Pan <sheng-liang.pan@quanta.corp-partner.google.com>
Change-Id: If7ead2d0bb2955a4f1b81d012ee2e2518b2a82e4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59373
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
ACPI_DEVICE_SLEEP_D3_COLD
Configure _DSC to ACPI_DEVICE_SLEEP_D3_COLD so that driver skips initial
probe during kernel boot and prevent privacy LED blink.
BUG=b:199823938
TEST=Build and boot redrix to OS. Verify entries in SSDT and monitor LED
during boot.
Signed-off-by: Varshit B Pandya <varshit.b.pandya@intel.com>
Change-Id: I88ea1b87698c63e1bd69367ee857fba3f25c84ea
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59260
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Add separate gpio table for TPM i2c and interrupt. Remove TPM gpios from
early_gpio_table. This allows for initializing TPM gpios separately from
other gpios.
BUG=b:200578885
BRANCH=None
TEST=Build and boot guybrush
Change-Id: I51d087087b166ec3bb3762bc1150b34db5b22f2f
Signed-off-by: Rob Barnes <robbarnes@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59083
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Based on Intel Kit#615686, USB3 only needs to disable TBT and DMA per
port. And if uses USB3 directly you need to set TcssAuxOri accordingly.
BUG=b:206716691,b:205235144
TEST=USB function work as expected at USB3 only sku.
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I303d042d6c80194ff48130fe4e9c04b49ca13ee8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59385
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Add SPD support to gimble for LPDDR4 memory part MT53E1G32D2NP-046 WT:B
and MT53E512M32D1NP-046 WT:B.
BUG=b:191574298
TEST=USE="project_gimble emerge-brya coreboot" and verify it builds
without error.
Signed-off-by: Mark Hsieh <mark_hsieh@wistron.corp-partner.google.com>
Change-Id: Id3fc35605675b953bf993a29f35140f7721eedab
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59299
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
After CB:57539 applied, it can support romstage GPIO table override.
We can move SSD PERST# de-assertion to romstage.
The reason for this is to give enough time after PERST#
deassertion so that the SSD has enough time to initialize before
the FSP scans the RPs for downstream devices.
BUG=b:199714453
TEST=build
Signed-off-by: Wisley Chen <wisley.chen@quanta.corp-partner.google.com>
Change-Id: I242cb1517f564d9d135d523b1e7f95ac34d601f8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59269
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Correct the WWAN power sequence to meet spec
BUG=b:206079177
TEST=build
Change-Id: Ibba1ecc04b563ae4eedd7596594f33812cbac150
Signed-off-by: Wisley Chen <wisley.chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59267
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Enable Acoustic noise mitigation for redrix and set slew rate to 1/8
BUG=b:204009588
TEST=build and verified by power team
Signed-off-by: Wisley Chen <wisley.chen@quanta.corp-partner.google.com>
Change-Id: I0fc0bb68c4de6fca60ee290eb46a77200d748ca8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58947
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Related to https://review.coreboot.org/c/coreboot/+/58555
commit-id: 35b7e0a2d82ac
In 58555, we added the SOC ID for Stoneyridge in amdfwtool
command line. But it raised building error because it then called
"set_efs_table" without setting SPI mode. So we skipped calling that.
But in set_efs_table, it has case for Stoneyridge. The boards also
need to have this setting. So we remove the skipping and give the
proper SPI mode in mainboard Kconfig.
Change-Id: I24499ff6daf7878b12b6044496f53379116c598f
Signed-off-by: Zheng Bao <fishbaozi@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58871
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Add MT53E1G32D2NP-046 WT:B SPD.
BUG=b:205669003
TEST=Boot up without issues.
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: If084a8af941b36a8f3f608271078e32b093d9108
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59348
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Windows (10/11) freaks out and generates an interrupt storm
if two ACPI devices are enabled and share an interrupt, even
when only one device is actually present. To mitigate this,
mark Cyan's touchpad/touchscreen interrupts as SharedAndWake
rather than ExclusiveAndWake.
Test: build/boot Windows 10 on Relm, observe normal CPU
usage in Task Manager for System Interrupts task when
touchpad/touchscreen in use.
Change-Id: I09bc878318f9fa6252f65a42ad46109418805fa0
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59336
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
According hareware design, mipi panel backlight relies on
AP_BKLTEN(GPIO_12) and TP_EN(GPIO_85). Meanwhile, TP_EN(GPIO_85)
needs pull up to enable PP3300_DISP_ON before AP_BKLTEN(GPIO_12) up.
BUG=b:197709288,b:199081803,b:205166230
BRANCH=trogdor
TEST=emerge-strongbad coreboot
Change-Id: Ie9920e5366f6b1ea9e0da228bd211317516b390a
Signed-off-by: Zanxi Chen <chenzanxi@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59044
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
Correct GPE settings so touchpad can wake up DUT.
BUG=b:206526991
TEST=emerge-brya coreboot and builds without error
Signed-off-by: Joey Peng <joey.peng@lcfc.corp-partner.google.com>
Change-Id: I1978e9220ad7a275d351ad5eeff7036131926b24
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59345
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: YH Lin <yueherngl@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Used H1 firmware where the last version number is 0.0.22, 0.3.22 or
less to production that will need to disable autonomous GPIO power
management and then can get H1 version by gsctool -a -f -M
BUG=b:205315500
TEST=emerge-brya coreboot and test that DUT can boot to OS.
Signed-off-by: Joey Peng <joey.peng@lcfc.corp-partner.google.com>
Change-Id: Ib26797fa2d4d0b1a6eb28c5d79b9ac0a6054abd8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59325
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: YH Lin <yueherngl@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
SSD sometimes can't be detected in in warm/cold boot stress.
M.2 spec describes SSD_PERST# should be sequenced after power enable.
BUG=b:199967106
TEST=SSD was always discovered in warm/cold boot stress.
Signed-off-by: Casper Chang <casper_chang@wistron.corp-partner.google.com>
Change-Id: I74c21cd96cf1c4518c4ed7c0b3b39e915b6b1ff7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59303
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Enable VBOOT_EARLY_EC_SYNC in corebot
BUG=b:201356952
BRANCH=None
TEST=Tested on Brya id 2
Signed-off-by: Boris Mittelberg <bmbm@google.com>
Change-Id: I6e480d64a5d90d5bb9cf59ed60b7b53af9edf46a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59274
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Add VBTs for all hatch variants currently supported by
ChromeOS recovery images. For variants which use multiple
VBTs and select at runtime, ensure these are added directly
to CBFS.
Change-Id: I3c62ce204e3272e778ba0a34f7a47a65d8125f53
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59329
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Change-Id: Ie29242e635bae1e2754bc1109754a64cb496af29
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59328
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
TypeC AUX configuration is variant specific. So move into variant level.
BUG=b:205235144
TEST=No typeC port 0 AUX in felwinter.
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I02bfea462cf4c6359fd8d5cca4368786ee03bc8b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59290
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
For Guybrush Board Version 2, Nipperking Board Version 1,
update SPKR GPIO to match H/W schematic:
SPKR: GPIO31
For Nipperkin Board Version 2, update SPKR GPIO to
match H/W schematic:
SPKR: GPIO70
BUG=b:202992077
BRANCH=guybrush
TEST=emerge-guybrush coreboot chromeos-bootimage
Change-Id: I3d82292b116f53d85d9518364ffd2169bd915a7e
Signed-off-by: Kevin Chiu <kevin.chiu@quantatw.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59051
Reviewed-by: Rob Barnes <robbarnes@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add VBTs for all octopus variants currently supported by
ChromeOS recovery images. For variants which use multiple
VBTs and select at runtime, ensure these are added directly
to CBFS.
Change-Id: I4b5c4268f9255d658f9762d94488db66e0677830
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59327
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Change-Id: I2e57c4f1baa8a42bde2642e7f76ddead7bfd6a58
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59326
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Windows (10/11) freaks out and generates an interrupt storm
if two ACPI devices are enabled and share an interrupt, even
when only one device is actually present. To mitigate this,
mark Peppy's interrupts as Shared rather than the default
of Exclusive.
Test: build/boot Windows 10 on Peppy, observe normal CPU
usage in Task Manager for System Interrupts task when
touchpad in use.
Change-Id: Ida78ddec3105cef6581cdde78da2e2c97d983a0a
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59330
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Add support for RTC and clkbuf.
TEST=boot to kernel and check log ok
BUG=b:202871018
Signed-off-by: Yuchen Huang <yuchen.huang@mediatek.corp-partner.google.com>
Change-Id: Ia02a74f685feb2466c113a77cbfa3a7d8fedb595
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59344
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
Initialize SPM (System Power Management) in RAM stage.
This adds 55ms to the boot time.
TEST=program counter of SPM is correct value(0x250) after booting up
BUG=b:202871018
Signed-off-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Change-Id: I822417f7a679107760b202dd43fb79d1934940bd
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59342
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
Setting of MSDC is defined by soc, so we move them to soc folder.
TEST=emerge-cherry coreboot; emerge-asurada coreboot
Signed-off-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Change-Id: I84ad8a4cde120c97024870ebf750d44b36c2284d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59339
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
In next phase build, the audio codec will change to ALC5682I-VS
BUG=b:205883511
TEST=emerge-brya coreboot chromeos-bootimage and check audio function
Signed-off-by: Malik_Hsu <malik_hsu@wistron.corp-partner.google.com>
Change-Id: I5906ef9bb88da7fe450a986bf7dd1ee701227f95
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59173
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
For tuning, redrix needs differnet dsm paramters file for L/R
speeker/tweeter.
BUG=b:204841998
TEST=build
Signed-off-by: Wisley Chen <wisley.chen@quanta.corp-partner.google.com>
Change-Id: I6f93603a6809f9a5aea9f2e554935de5d0457286
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59241
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Some eMMCs need 80+ms for CMD1 to complete. And the payload may need to
access eMMC in the very early stage (for example, depthcharge needs it
20ms after started) so we have to start initialization in coreboot.
TEST=boot kernel from eMMC ok
BUG=b:202871018
Signed-off-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Change-Id: I3bc06b1fc506b1d6f54f7f456117d22477a87e29
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59294
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
The Corsola reference design has both eMMC and SD Card interfaces
so we have to configure both in RAM stage.
TEST=boot kernel from eMMC and SDCard ok
BUG=b:202871018
Signed-off-by: Wenbin Mei <wenbin.mei@mediatek.com>
Change-Id: I0fa8712eb61685a305dc5dd49cc2e55f1f0eecd4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59293
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
The Corsola reference design has both eMMC and SD Card interfaces
so we have to configure both in RAM stage.
TEST=build pass
BUG=b:202871018
Signed-off-by: Wenbin Mei <wenbin.mei@mediatek.com>
Change-Id: I2f26a8a11edd29a80a7195e3a324151d66ecb293
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59292
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
Add the support LP5 RAM parts for vell:
DRAM Part Name ID to assign
MT62F512M32D2DR-031 WT:B 0 (0000)
MT62F1G32D4DR-031 WT:B 1 (0001)
BUG=b:204284866
TEST=emerge-brya coreboot
Change-Id: I49745948ebdb25fd98e285defd75714f80271968
Signed-off-by: Kevin Chiu <Kevin.Chiu@quantatw.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59288
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Reka Norman <rekanorman@chromium.org>
|
|
In CL:3248796 GPIO_5 was made the default for SD_AUX_RESET_L. No variant
is actually using GPIO_5 for SD_AUX_RESET_L. Making GPIO_69 the default
and only overriding to GPIO_70 for guybrush bid==1.
BUG=b:202992077
BRANCH=None
TEST=Build and boot guybrush, SD card works
Change-Id: I6546ad9961f6f7146aa3aefc35d39a2eb282a252
Signed-off-by: Rob Barnes <robbarnes@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59053
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Redrix has 4 thermal sensors, so add the missing sensors settings.
BUG=b:200134784
TEST=build and verified by thermal team.
Signed-off-by: Wisley Chen <wisley.chen@quanta.corp-partner.google.com>
Change-Id: Ia9c58129d439ade21e96896c5e593cd08a627603
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58970
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
|
|
As Hoglin variant was recently added, need to make sure that it uses
the same configs as piglin.
BUG=b:197366666
BRANCH=None
TEST=create hoglin image and make sure that it boots on CRD 2.0
Change-Id: I14497a205262ac1081c24631e4fd8d39bb804fce
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59273
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This reverts commit adb393bdd6cd6734fa2672bd174aca4588a68016.
This relands commit 6260bf712a836762b18d80082505e981e040f4bc.
Reason for revert:
The original CL did not handle some devices correctly.
With the fixes:
* commit 36721a4 (mb/google/brya: Add GPIO_IN_RW to all variants'
early GPIO tables)
* commit 3bfe46c (mb/google/guybrush: Add GPIO EC in RW to early
GPIO tables)
* commit 3a30cf9 (mb/google/guybrush: Build chromeos.c in verstage
This CL also fix the following platforms:
* Change to always trusted: cyan.
* Add to early GPIO table: dedede, eve, fizz, glados, hatch, octopus,
poppy, reef, volteer.
* Add to both Makefile and early GPIO table: zork.
For mb/intel:
* adlrvp: Add support for get_ec_is_trusted().
* glkrvp: Add support for get_ec_is_trusted() with always trusted.
* kblrvp: Add support for get_ec_is_trusted() with always trusted.
* kunimitsu: Add support for get_ec_is_trusted() and initialize it as
early GPIO.
* shadowmountain: Add support for get_ec_is_trusted() and initialize
it as early GPIO.
* tglrvp: Add support for get_ec_is_trusted() with always trusted.
For qemu-q35: Add support for get_ec_is_trusted() with always trusted.
We could attempt another land.
Change-Id: I66b8b99d6e6bf259b18573f9f6010f9254357bf9
Signed-off-by: Hsuan Ting Chen <roccochen@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58253
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
PCIE port 6 is empty as per schematics.
BUG=b:206047996
TEST=PCIE port 6 is disabled.
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I30fa897c9310c44545e3df670895639a5144e1de
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59243
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
USB2 port 0 is empty as per schematics.
BUG=b:206047996
TEST=USB2 port 0 is disabled.
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I45d467a80c23d82dc33dcbed176430a758eea403
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59236
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Enable garage pen detection.
BUG=b:197912223
TEST=Check evtest can trigger event when toggling the switch.
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: Ib5929c876d1a0da34dadd7997a61ab8e75acbbb6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59234
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Enable RTD3 driver for PCIe-eMMC bridge, If the board version is less
than 1, do not enable RTD3 driver.
BUG=b:204469567
TEST=Boot into eMMC storage and perform suspend stress 100 cycle passed
Signed-off-by: Malik_Hsu <malik_hsu@wistron.corp-partner.google.com>
Change-Id: I5836d65cedfe3907af2c4c33de7a396c4bb8b727
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59135
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Update PL1 minimum value from 3W to 12W as per the thermal design
discussed in this bug 203371203 comment #10.
BUG=b:203371203
BRANCH=None
TEST=Build and boot the gimble system
Change-Id: Id66cfb6f6dc0217bd4d83eae1d66ad867a1bdb46
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58650
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Scott Chao <scott_chao@wistron.corp-partner.google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Kano has 3 thermal sensors, so add the missing sensor settings.
BUG=b:205648035
TEST=build pass
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Change-Id: I0da25f142149f94c83fdf7b2ba2cb8694cddb412
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59089
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
|
|
Create the vell variant of the brya0 reference board by copying
the template files to a new directory named for the variant.
(Auto-Generated by create_coreboot_variant.sh version 4.5.0).
BUG=b:205908918
BRANCH=None
TEST=util/abuild/abuild -p none -t google/brya -x -a
make sure the build includes GOOGLE_VELL
Signed-off-by: Shon Wang <shon.wang@quanta.corp-partner.google.com>
Change-Id: Ide8ba1c0dd9b5d9ad90556053abf2a597136a10c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59242
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Add VMCH and VMC for providing power of SDCard.
TEST=build pass
BUG=b:202871018
Signed-off-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Change-Id: I50fc87415086eb22ff35d157dba38cfd7594cc40
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59255
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
1. Enable and setup USB drivers.
2. Pull up to a weak resistor for USB3_HUB_RST_L and we reset
the hub via GPIO149.
TEST=boot kernel from USB ok
BUG=b:202871018
Signed-off-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Change-Id: Ifcc11d51b0c1e495477957111e6021ef8275f629
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59251
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
Use regulator interface to use regulator more easily.
TEST=build pass
BUG=b:202871018
Signed-off-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Change-Id: Ied43cba51036c62a120df2afffeb63b5d73f012b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59250
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
The 'corsola' reference design will include two implementations
with different BOM selections - 'krabby' and 'kingler'.
TEST=none
BUG=b:202871018
Signed-off-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Change-Id: Iaf9c6af1a395030937a9a5c00e95d7246ddcb6eb
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59249
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
Add basic support for VCORE/VDRAM1/VDDQ of MT6366.
TEST=build pass
BUG=b:202871018
Signed-off-by: James Lo <james.lo@mediatek.corp-partner.google.com>
Change-Id: I22e30421560a32f4a9e15899e8150376b1414494
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59245
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
Add separate gpio table for early eSPI bus init. Remove espi GPIO from
early_gpio_table. This allows for initializing eSPI separately from
other GPIOs. Simplify verstage_mainboard_early_init.
BUG=b:200578885
BRANCH=None
TEST=Build and boot guybrush
Change-Id: I0cd439f207df7c27575ae363b207293d40485bf8
Signed-off-by: Rob Barnes <robbarnes@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59082
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Kangheui Won <khwon@chromium.org>
|
|
This reverts commit ba6fdc892d62741e456ac5628fcd6f869c4cb9af.
Reason for revert: Refer to intel doc #627075 (Intel_600_Series Chipset_Family_PCH_GPIO_Impl_Sumry_ Rev1p5p1), GPP_R6 ~ GPP_R7 should be NF3 for dmic.
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Change-Id: I460fd99b4ad4b9c470f692032ff7ea2b51cad388
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59149
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Change-Id: I6e742b9d5256da2b7edcca0efda4faf999207465
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59192
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Do not place console output in low-level GPIO functions.
The caller of get_recovery_mode_switch() is in vboot_logic.c
that is linked in romstage. So presumably recovery mode
is broken and is not fixed with this commit either.
Change-Id: I2a0fdbb370d54898c72adb29a0e9b990a5fc0ce1
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59003
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Modify BOE panel_id for mrbland due to hardware changes.
BUG=b:205166230,b:198548221
BRANCH=trogdor
TEST=emerge-strongbad coreboot
Change-Id: I65fecd854c4e3443edc07a44a1d43572d5030e4c
Signed-off-by: Zanxi Chen <chenzanxi@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58995
Reviewed-by: xuxinxiong <xuxinxiong@huaqin.corp-partner.google.com>
Reviewed-by: Bob Moragues <moragues@google.com>
Reviewed-by: Shelley Chen <shchen@google.com>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Used H1 firmware where the last version number is 0.0.22, 0.3.22 or
less to production that will need to disable autonomous GPIO power
management and then can get H1 version by gsctool -a -f -M
BUG=b:201054849
TEST=USE="project_primus emerge-brya coreboot" and verify it builds
without error.
Change-Id: If5a99a96e5d4b84be3f2c1165283ce249ca75d58
Signed-off-by: Casper Chang <casper_chang@wistron.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59079
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Low-level GPIOs should not depend on late cros_gpios that
should be guarded with CHROMEOS and implemented for the
purpose of ACPI \OIPG package generation.
Change-Id: Ibe708330504bc819e312eddaf5dfe4016cda21a1
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59004
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Change-Id: Ia473596e3c9a75587cd1288c8816bfef66bef82e
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59000
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Enable SaGv.
BUG=b:198235324
TEST=Boot into without issues.
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I3cbff8d28bb5b5bfdad323f348b9f880245d049d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59095
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Disable unused USB2 and USB3 port
BUG=b:192370253
TEST=build pass
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Change-Id: Ia2fa10fb21e0a42e51728bc3d78163ca213f8d91
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59084
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Use gpio_keys driver to add ACPI node for pen eject event. Also
setting gpio wake pin for wake events.
BUG=b:192415743
TEST=build pass
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Change-Id: Ia36119678cfd5c65a62685d3312537d9aa21e83b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59035
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
|
|
Currently all the power sequencing for FPMCU is done explicitly in
different stages of coreboot. This can all be done by adding ACPI power
resources for FPMCU and clean up the unused code. Here is the expected
power sequence:
PowerUp : Assert EN_PWR_FP -> 3 ms delay -> De-assert FPMCU_RST_ODL
Shutdown : De-assert EN_PWR_FP -> Assert FPMCU_RST_ODL
Reboot : Shutdown -> 200 ms delay -> PowerUp
BUG=None
TEST=Build and boot to OS in Guybrush. Ensure that the FP is able to
unlock the system after the first login attempt. Ensure that the FP is
able to wakeup the system. Observed that the power resource is added
correctly in the FPMCU ACPI object
Name (_PR0, Package (0x01) // _PR0: Power Resources for D0
{
PR01
})
Name (_PR3, Package (0x01) // _PR3: Power Resources for D3hot
{
PR01
})
PowerResource (PR01, 0x00, 0x0000)
{
Method (_STA, 0, NotSerialized) // _STA: Status
{
Return (0x01)
}
Method (_ON, 0, Serialized) // _ON_: Power On
{
\_SB.CTXS (0x0B)
\_SB.STXS (0x20)
\_SB.STXS (0x0B)
}
Method (_OFF, 0, Serialized) // _OFF: Power Off
{
\_SB.CTXS (0x0B)
\_SB.CTXS (0x20)
}
}
Change-Id: I52322eaecf6961ff9a196ca9ab2d58b7d4599d4f
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58705
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Rob Barnes <robbarnes@google.com>
|
|
Modify settings to enable CPU PCIE RP 1 according to schematics.
BUG=b:205504257
TEST=emerge-brya coreboot and can successfully boot with ssd and emmc.
Signed-off-by: Joey Peng <joey.peng@lcfc.corp-partner.google.com>
Change-Id: I0f817c860f2b295c6aa84fa1999d374d99f817f6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59080
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
copy config from guybrush reference board.
BUG=b:204151079
BRANCH=guybrush
TEST=emerge-guybrush coreboot chromeos-bootimage
Signed-off-by: Chris.Wang <chris.wang@amd.corp-partner.google.com>
Change-Id: Ide9e002390e59725dc0e45f83280db2a78270993
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59092
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Rob Barnes <robbarnes@google.com>
|
|
- Set MAX OC1 to USB2_C1
BUG=b:205676803
TEST=USE="project_gimble emerge-brya coreboot" and verify it builds
without error.
Signed-off-by: Mark Hsieh <mark_hsieh@wistron.corp-partner.google.com>
Change-Id: Idcf13ad072ae5d7a897f54adb19e6b2b068609dc
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59100
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Zhuohao Lee <zhuohao@google.com>
|
|
We need to put USB setting in mux order.
BUG=b:204230406
TEST=Type C mux configuration is correct.
Wrong:
added type-c port0 info to cbmem: usb2:2 usb3:2 sbu:0 data:0
added type-c port1 info to cbmem: usb2:3 usb3:3 sbu:0 data:0
Correct:
added type-c port0 info to cbmem: usb2:3 usb3:3 sbu:0 data:0
added type-c port1 info to cbmem: usb2:2 usb3:2 sbu:0 data:0
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I19338e162db6145dbeb5830de1a372cf98f779a0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59012
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
|
|
Divide dsm_param_file_name into dsm_param_R and dsm_param_L
BUG=b:205684021
TEST=build and check SSDT
Signed-off-by: Mark Hsieh <mark_hsieh@wistron.corp-partner.google.com>
Change-Id: Ie2db709a63152c1ccee2f7d594284e366ada8a01
Reviewed-on: https://review.coreboot.org/c/coreboot/+/59046
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add wifi sar for galtic/galtic360/galith360
Using convertible mode of SKU ID to load wifi table.
Each Project and SKU ID correspond as below
galtic (sku id:0x120000)
galith (sku id:0x130000)
gallop (sku id:0x150000)
galtic360 (sku id:0x260000)
galith360 (sku id:0x270000)
BUG=b:203741126
TEST=emerge-dedede coreboot chromeos-bootimage \
coreboot-private-files-baseboard-dedede
verify the SAR table is correct in each project
Signed-off-by: FrankChu <frank_chu@pegatron.corp-partner.google.com>
Change-Id: If4203d176dd717fa62c88d9b4fab8a53847213fe
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58734
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marco Chen <marcochen@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Change-Id: I4052baca2d8041b2a6d6fd410fcf99248662d7a5
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58998
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
It's commented in <types.h> that it shall provide <commonlib/helpers.h>.
Fix for ARRAY_SIZE() in bulk, followup works will reduce the number
of other includes these files have.
Change-Id: I2572aaa2cf4254f0dea6698cba627de12725200f
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58996
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Enable DPTF based thermal control functionality for tpch device
on brya device.
BUG=b:198582766
BRANCH=None
TEST=Build FW and test on brya0 board
Change-Id: I6a35a101599bb811fcddaabab5296f8c6c12af31
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57098
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Currently, the MMCONF Kconfigs only support the Enhanced Configuration
Access mechanism (ECAM) method for accessing the PCI config address
space. Some platforms have a different way of mapping the PCI config
space to memory. This patch renames the following configs to
make it clear that these configs are ECAM-specific:
- NO_MMCONF_SUPPORT --> NO_ECAM_MMCONF_SUPPORT
- MMCONF_SUPPORT --> ECAM_MMCONF_SUPPORT
- MMCONF_BASE_ADDRESS --> ECAM_MMCONF_BASE_ADDRESS
- MMCONF_BUS_NUMBER --> ECAM_MMCONF_BUS_NUMBER
- MMCONF_LENGTH --> ECAM_MMCONF_LENGTH
Please refer to CB:57861 "Proposed coreboot Changes" for more
details.
BUG=b:181098581
BRANCH=None
TEST=./util/abuild/abuild -p none -t GOOGLE_KOHAKU -x -a -c max
Make sure Jenkins verifies that builds on other boards
Change-Id: I1e196a1ed52d131a71f00cba1d93a23e54aca3e2
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57333
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Set RFI Spread Spectrum to 6% for Redrix as RF team request.
The default of Spread Spectrum in FSP is 1.5%, and set 1.5% in baseboard
as default.
BUG=b:200886627
TEST=build
Signed-off-by: Wisley Chen <wisley.chen@quanta.corp-partner.google.com>
Change-Id: Id0b42446e9e46ef629b5ca8d5d29faf2d771348d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58880
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
For the Qualcomm PBL configuration of GPIO, we need to initial the
GPIOs for VDD33# and RST# at the beginning of coreboot. According to
the pa8640 latest spec v1.4, update the sequence of VDD33# and PD#.
BUG=b:204637643
BRANCH=trogdor
TEST=verified the waveform of ps8640 at coreboot phase.
Signed-off-by: xuxinxiong <xuxinxiong@huaqin.corp-partner.google.com>
Change-Id: Ia378aafa49ec462c990501ce48721e330d9648b0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58994
Reviewed-by: Wentao Qin <qinwentao@huaqin.corp-partner.google.com>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Probe the fw_config for RT1015 speaker amplifier operation mode and
enable it accordingly in the device tree.
BUG=none
BRANCH=dedede
TEST=build pass
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Change-Id: I2de1487b7f4767e9ba6432174c39feeb25f9534c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58931
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
This change adjusts all I2C speed to lower then 400KHz. The rise_time_ns
and fall_time_ns values for each port are capured by a scope.
BUG=None
BRANCH=dedede
TEST=built and verified adjusted I2C speed < 400KHz
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.corp-partner.google.com>
Change-Id: I9504608dd8d9a5f5a3848ef34691557942c21023
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58965
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Add ELAN touchscreen support for magneto.
BUG=b:203122673
TEST=Build and verify that touchscreen works.
Signed-off-by: Tyler Wang <tyler.wang@quanta.corp-partner.google.com>
Change-Id: Ie86692901113e952c597fcfc6c58e7ee0fc172fa
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58967
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Update charger performance control table of DPTF for bugzzy.
Since the EC change chromium:197776876 modified maximum charging current
to reduce skin temperature, this change adjusts the charging performance
table with the modified value.
BUG=b:197776876
BRANCH=dedede
TEST=emerge-dedede coreboot
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.corp-partner.google.com>
Change-Id: I33e176fcf5d380b315ff352c6c65af3b8b93c4b9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58840
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
BUG=None
BRANCH=dedede
TEST=enable CHROMEOS_WIFI_SAR in config of coreboot,
emerge-dedede coreboot chromeos-bootimage
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.corp-partner.google.com>
Change-Id: Ie967ef7fbc19886c631e634a0b0c3f2cf1e490af
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58845
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Henry Sun <henrysun@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Change-Id: Ibbdd589119bbccd3516737c8ee9f90c4bef17c1e
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58923
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
Avoid indirect <vc/google/chromeos/chromeos.h> as the
files really only need <security/vboot/vboot_common.h>.
Change-Id: Ic02bd5dcdde0bb5c8be0e2c52c20048ed0d4ad94
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58949
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
SPI speed override is not related to ChromeOS, thus the
location in chromeos.c was poor choice.
Change-Id: Ie3db89f252af1f44e9539497c05bdf965565a191
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58945
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Change-Id: I9e7200d60db4333551e34a615433fa21c3135db6
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58921
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Change-Id: I882c567e6bca0982a0d3d44c742777c4d7bd5439
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58920
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Add NOR-Flash drivers to pass verification of flash at verstage.
TEST=boot to romstage
BUG=b:202871018
Signed-off-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Change-Id: Iee3dd336632b0cf998f5f7c1d118e01e8270e815
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58838
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
This patch sets the enable the external voltage rails since taeko
board have V1p05 and Vnn bypass rails.
BRANCH=None
BUG=b:204832954
TEST=FW_NAME=Check in FSP log and run PLT test
Signed-off-by: Kevin Chang <kevin.chang@lcfc.corp-partner.google.com>
Change-Id: I20ff310d48d3e7073fe5e94d03d29cc55a46d1f9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58943
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Type C port2 uses EC mux port0 as per schematics.
BUG=b:204230406
TEST=No error message in depthahrge.
update_port_state: port C2: get_usb_pd_mux_info failed
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I85218c81018b248c41a2cdaf9360a86e2a7d4d7a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58930
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Add OEM product names from public sources.
Change-Id: Ic051aa9c8afabd47e7e9f6ac878190d9904ef757
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58911
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Currently link_speed_capability is not specified within the DXIO
descriptors sent to FSP. This value specifies the maximum speed that
a PCIe device should train up to. The only device on Monkey Island that
is not currently running at full speed is the NVME but this may not
always be the case.
BUG=b:204791296
TEST=Boot to OS and check link speed with LSPCI to verify
NVME link speed goes from 2.5 GT/s to 5 GT/s
Change-Id: Ibeac4b9e6a60567fb513e157d854399f5d12aee9
Signed-off-by: Matt Papageorge <matthewpapa07@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58799
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
Refer to intel doc #627075 (Intel_600_Series Chipset_Family_PCH_GPIO_Impl_Sumry_ Rev1p5p1)
Set GPIO GPP_S0 ~ GPP_S3 to NF4 and GPP_R6 ~ GPP_R7 to NF3.
BUG=b:204844177 b:202913826
TEST=build pass
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Change-Id: Iafe52ec3a6deead1d2fc5ada0f2842cf2a9f41a4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58877
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: CT Lin <ctlin0@nuvoton.corp-partner.google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
All of these names came from public sources.
Signed-off-by: Martin Roth <martin@coreboot.org>
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Change-Id: I1ed9cc0c1ff63dc415e0cc63fa9d2dcd429a093b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57392
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Setting the PM_ESPI_CS_USE_DATA2 bit in PM_SPI_PAD_PU_PD results in the
eSPI transactions being sent via the SPI2 pins instead of the SPI1 pins.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Iad8e3a48496a52c14c936ab77c75dc1b403f47bb
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58876
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
The name looked a bit odd and the Cezanne PPR #56569 Rev 3.03 confirmed
that the native function names don't have the EMMC_ prefix.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I917c74afd98f2e2133e160d352f11f08c19a3ec6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58874
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
BUG=b:204272905
BRANCH=master
TEST=emerge-trogdor coreboot
Signed-off-by: Kevin Chiu <kevin.chiu@quantatw.com>
Change-Id: Ie13ddfef6adfd53adb0a0d3a98995fb00b8a45e6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58789
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philip Chen <philipchen@google.com>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
Add mainboard folder and drivers for new reference board 'Corsola'.
TEST=build pass
BUG=b:200134633
Signed-off-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Change-Id: I2d701c03c97d3253effb6e93a2d55dcf6cf02db6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58648
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Rex-BC Chen <rex-bc.chen@mediatek.corp-partner.google.com>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
This reverts commit 287cc02c007fd47b515d19389ea00ea0461fd5a1.
Reason for revert: it will break s0ix.
BUG=b:201266532
TEST=build pass
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Change-Id: I393077b26e2cdeae055d8eea1030754602e94ada
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58809
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Enable MKBP (Matrix Keyboard Protocol) interface for all volteer family
to use for buttons and switches. Disable TBMC (Tablet Mode Switch
device), as it is not needed anymore.
BUG=b:171365305
TEST=manual test on Volteer:
Volume Up/Down and Power buttons, Tablet Mode switch
Signed-off-by: FrankChu <frank_chu@pegatron.corp-partner.google.com>
Change-Id: I2bb2e895af17fa4280113e57e2b0ca780af8840e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58741
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Boris Mittelberg <bmbm@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Update guybrush STT (Skin Temperature Tracking) configuration settings
to values provided by power team after tuning.
BUG=b:203123658
Change-Id: I14c69dbe044e4f3f2711be96e5ea80db0686b3eb
Signed-off-by: Jason Glenesk <jason.glenesk@amd.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58674
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Rob Barnes <robbarnes@google.com>
|
|
Currently, the address size field of AT24 NVM is incorrect, and
Linux v5.10 kernel logs the message below:
at24 i2c-PRP0001:01: Bad "address-width" property: 14
The valid size of the AT24 NVM is 16 bits so modify the value from
0x0E to 0x10.
TEST=Boot brya and check the kernel log and see "Bad address-width"
error message is not shown.
Signed-off-by: Varshit B Pandya <varshit.b.pandya@intel.com>
Change-Id: I6c1ed5334396e0ca09ea0078426a7b5039ae4e8b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58769
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
|
