| Age | Commit message (Collapse) | Author |
|---|
|
Recent changes to the ITE 8772F SIO code caused the initial fan PWM
to change from 0 to 50%; set it to 30% to reduce fan noise while
still providing some temp control before the OS/ACPI takes over.
TEST=build/boot google/beltino to payload, verify fan noise is
negligible.
Change-Id: I0177235d73e051f02b5333cf1d735556382b919f
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81513
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Varshit Pandya <pandyavarshit@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The it8772f is now configured by the much better common code that is
used for other chips in the family as well. This mainly concerns the EC,
the GPIO functionality was not moved to common as it currently lacks a
sane abstraction in any codebase.
The datasheets of the it8772e(f) and it8728f (for reference) were
studied and verified against the common code, adding exceptions where
needed.
Change-Id: Ic4d9d5460628e444dc20f620179b39c90dbc28c6
Signed-off-by: Joel Linn <jl@conductive.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81310
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
|
|
The GPIO for NOTE_BOOK_MODE has changed from GPP_B17 to GPP_E9. Also
initializing it (if ISH is enabled) to be NF2 (ISH_GP4). Also took
the liberty of alphabetizing all the ISH GPIOs to they're easier to
search through.
BUG=b:316421831
BRANCH=None
TEST=emerge-brox coreboot chromeos-bootimage
Make sure that brox device still boots up with this change.
Change-Id: I4a091b58deb855c7a7f1489a9506db2f821503b7
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81789
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: Eric Lai <ericllai@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Fill GPIO table for Sundance.
BUG=b:327520553
TEST=emerge-nissa coreboot
Change-Id: I53ed5874347006985ca5231d1531fa519088f796
Signed-off-by: Leo Chou <leo.chou@lcfc.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81613
Tested-by: Martin L Roth <gaumless@gmail.com>
Reviewed-by: Derek Huang <derekhuang@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
|
|
Change-Id: I66265727b68b6ad10722439314b466298dbfff28
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81821
Reviewed-by: Yidi Lin <yidilin@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
In next phase, craaskov will remove external fivr. Use the board
version to config external fivr for backward compatibility and
show message.
BUG=b:330253778
TEST=boot to ChromeOS, cold reboot/suspend/recovery mode/install OS
work normally.
Change-Id: I9280a86bf78caa10b527a6569ac580dfe1d66f60
Signed-off-by: Ian Feng <ian_feng@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81607
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
BUG=b:333605309
TEST=set and unset bit20 in HW_CONFIG and check if VPU(0b.0)
is enabled when bit20 is set, and disabled when cleared.
Change-Id: I6e2230715d783ea7108d71699fd19684ce19e2ff
Signed-off-by: Jamie Ryu <jamie.m.ryu@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81655
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
This patch adds a new variant trulo for the baseboard trulo.
BUG=b:333314089
TEST=abuild -a -x -p none -t google/brya
Change-Id: I91157d252ef56c8938bfc08ed0f734c5dc7e614d
Signed-off-by: Dinesh Gehlot <digehlot@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81627
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
|
|
This patch adds a new baseboard trulo. This commit is a stub which
only adds the minimum code needed for a successful build.
BUG=b:333314089
TEST=abuild -a -x -p none -t google/brya
Change-Id: Iad6230064c6b8359698d37c3e0440614cc7b073d
Signed-off-by: Dinesh Gehlot <digehlot@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81626
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
|
|
Change-Id: I0e216cbc4acf9571c65c345a1764e74485f89438
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81818
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I40e2e5a786499abbe2fce63d6e0f1ac1e780ab51
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81816
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Varshit Pandya <pandyavarshit@gmail.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Eric Lai <ericllai@google.com>
|
|
Change-Id: I26c2abfce3417ed096d945745770fcae91a1e4ad
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81814
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Dinesh Gehlot <digehlot@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Varshit Pandya <pandyavarshit@gmail.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Eric Lai <ericllai@google.com>
|
|
Set orientation of KD_KD101NE3_40TI to LB_FB_ORIENTATION_RIGHT_UP to
align the volume up/down direction with menu up/down in FW screen.
BUG=b:331870701
TEST=emerge-staryu coreboot chromeos-bootimage, and check FW screen on
wugtrio, test volume key behaves as expected.
BRANCH=corsola
Change-Id: Ie101cc8b983d3d16587f88fa787ed622e59d27eb
Signed-off-by: Yang Wu <wuyang5@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81752
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Yidi Lin <yidilin@google.com>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch renames the 16MB FMD file to remove the baseboard-specific
name 'Nissa'. This allows other supported baseboards to utilize the
16MB SPI flash. Additionally, the patch attempts to create a generic,
unified 32MB FMD file for both brya and nissa variants.
BUG=b:333314089
TEST=Build and boot Nivviks.
Change-Id: I9151a4bcbe9cc084cc19b1a3e91c0321fe4dcc37
Signed-off-by: Dinesh Gehlot <digehlot@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81676
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Varshit Pandya <pandyavarshit@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I265e427254ce9f735e65b0631c43f98bc778a34f
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81812
Reviewed-by: Jonathon Hall <jonathon.hall@puri.sm>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Varshit Pandya <pandyavarshit@gmail.com>
Reviewed-by: Yidi Lin <yidilin@google.com>
|
|
Change-Id: Ib1a8fc50217c84e835080c70269ff50fc001392c
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81811
Reviewed-by: Varshit Pandya <pandyavarshit@gmail.com>
Reviewed-by: Jonathon Hall <jonathon.hall@puri.sm>
Reviewed-by: Yidi Lin <yidilin@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The header file console/console.h is unused, just drop it.
TEST=abuild -t google/corsola -b wugtrio -a
TEST=abuild -t google/geralt -b ciri -a
Signed-off-by: Ruihai Zhou <zhouruihai@huaqin.corp-partner.google.com>
Change-Id: If3689afe532b63384b7905116c44c598e5fa13ee
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81685
Reviewed-by: Yidi Lin <yidilin@google.com>
Reviewed-by: Eric Lai <ericllai@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-by: cong yang <yangcong5@huaqin.corp-partner.google.com>
|
|
Correct verbtable value for pin widget 20 of Realtek ALC256 based on the
updated verbtable received from Realtek. Updated Version : 5.0.3.1. This
fixes the headset detection failure, when power_save is enabled in
legacy hda driver.
BUG=b:330433089
BRANCH=None
TEST=Verified headset on Brox
When connected to audiojack in power_save state of legacy hda driver,
headset is detected and audio is resumed.
Change-Id: I71b7d59b3ab5310a0b6cdb31fb5033f94263d151
Signed-off-by: Poornima Tom <poornima.tom@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81654
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Terry Cheong <htcheong@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Shelley Chen <shchen@google.com>
|
|
Change-Id: I878c14058e1edc0f64e37c2fc16b8dcf75b90192
Signed-off-by: Varshit Pandya <pandyavarshit@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81631
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Dinesh Gehlot <digehlot@google.com>
|
|
BUG=b:332488817
TEST=set and unset bit20 in HW_CONFIG and check if VPU(0b.0)
is enabled when bit20 is set, and disabled when cleared
Change-Id: I6d7b35dbf8ac9b0abb42f64a947b4bb94f3c6b0f
Signed-off-by: Jamie Ryu <jamie.m.ryu@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81560
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Varshit Pandya <pandyavarshit@gmail.com>
Reviewed-by: Daniel Kang <daniel.h.kang@intel.com>
|
|
Based on schematic and gpio table of sundance, generate overridetree.cb
settings for sundance.
BUG=b:328505938
TEST=FW_NAME=sundance emerge-nissa coreboot chromeos-bootimage
Change-Id: I857be7bc7f98281cac57fef85bf9f3cef2ec14e9
Signed-off-by: Leo Chou <leo.chou@lcfc.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81653
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <ericllai@google.com>
|
|
I2C slave addresses 0x41.
BUG=b:332458912
BRANCH=None
TEST=emerge-nissa coreboot & working correctly in DUT
Change-Id: I2d26bfd4f415aa128b6256f83bc58987b15a557a
Signed-off-by: Yunlong Jia <yunlong.jia@ecs.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81610
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Varshit Pandya <pandyavarshit@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
When battery level is below critical level or battery is not present,
cpus need to run with a power optimized configuration to avoid platform
instabilities such as system power down.
This will check the current battery status and configure cpu power
limits using current PD power value.
BUG=b:328729536
BRANCH=brya
TEST=built and verified MSR PL2/PL4 values.
Intel doc #614179 introduces how to check current PL values.
[Original MSR PL1/PL2/PL4 register values for xol]
cd /sys/class/powercap/intel-rapl/intel-rapl\:0/
grep . *power_limit*
constraint_0_power_limit_uw:15000000 <= MSR PL1 (15W)
constraint_1_power_limit_uw:55000000 <= MSR PL2 (55W)
constraint_2_power_limit_uw:114000000 <= MSR PL4 (114W)
[When connected 60W adapter without battery]
Before:
constraint_0_power_limit_uw:15000000
constraint_1_power_limit_uw:55000000
constraint_2_power_limit_uw:114000000
After:
constraint_0_power_limit_uw:15000000
constraint_1_power_limit_uw:55000000
constraint_2_power_limit_uw:60000000
[When connected 45W adapter without battery]
Before:
constraint_0_power_limit_uw:15000000
constraint_1_power_limit_uw:55000000
constraint_2_power_limit_uw:114000000
After:
constraint_0_power_limit_uw:15000000
constraint_1_power_limit_uw:45000000
constraint_2_power_limit_uw:45000000
Change-Id: I5d71e9edde0ecbd7aaf316cd754a6ebcff9da77d
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81614
Reviewed-by: Jamie Chen <jamie.chen@intel.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
In order to avoid the noise caused by the codec output to the audio
jack during the shutdown and poweron process, we will use GPP_A11 for
the codec power supply gate, keep low during the startup process, and
wait for the driver to turn on. This change does not affect the beep
output of depthcharge.
BUG=None
TEST=There is no squeaking sound when turning on and off
Change-Id: I5982be5a8d965086b46861f4c2c758d9bdee6e75
Signed-off-by: Jianeng Ceng <cengjianeng@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81629
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
|
|
Add a new Staryu follower device 'Wugtrio'. And also enables SD card
support and MIPI panel support.
BUG=b:331870701
TEST=emerge-staryu coreboot chromeos-bootimage
BRANCH=corsola
Change-Id: I586de68da4d0ee2dd5b7baea92ebb06db9fcfe8b
Signed-off-by: Yang Wu <wuyang5@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81585
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Reviewed-by: Yidi Lin <yidilin@google.com>
Reviewed-by: Varshit Pandya <pandyavarshit@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Move starmie mipi panel selection from BOARD_GOOGLE_STARYU_COMMON
section to BOARD_SPECIFIC_OPTIONS section.
BUG=None
TEST=emerge-staryu coreboot chromeos-bootimage
BRANCH=corsola
Change-Id: Ib5792542f55a78c0840b6169b5ecf092e7cefe98
Signed-off-by: Yang Wu <wuyang5@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81602
Reviewed-by: Yidi Lin <yidilin@google.com>
Reviewed-by: Eric Lai <ericllai@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Ruihai Zhou <zhouruihai@huaqin.corp-partner.google.com>
Reviewed-by: Varshit Pandya <pandyavarshit@gmail.com>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
Enable SMLINK1 interface for PMC-PD communication to configure Type-C
muxes.
Refer RPL EDS vol 1: 765585.
BUG=b:327622474
BRANCH=None
TEST=Boot image on SKU2 and check PMC-PD working.
Change-Id: Ia678d291e7a14aefe09026e70478fea3f68c8e10
Signed-off-by: Ashish Kumar Mishra <ashish.k.mishra@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81207
Reviewed-by: Eric Lai <ericllai@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Deepti Deshatty <deepti.deshatty@intel.com>
|
|
Make get_soc_power_limit_config() a public function to use on brya
variants. Add prefix 'variant_' for it.
BUG=None
BRANCH=brya
TEST=emerge-brya coreboot
Change-Id: I31f938938e7c9da49c2aa7b52dd4b5f46f793495
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81616
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <ericllai@google.com>
|
|
Add sundance supported memory parts in mem_parts_used.txt, generate
SPD id for this part.
1. Samsung K3KL6L60GM-MGCT, K3KL8L80CM-MGCT
2. Hynix H58G56AK6BX069, H9JCNNNBK3MLYR-N6EE
BUG=b:332201349
TEST=Use part_id_gen to generate related settings
Change-Id: Ieece88b0b2b2ea5f0d6192ee8441e50d3f22a972
Signed-off-by: Leo Chou <leo.chou@lcfc.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81612
Reviewed-by: Eric Lai <ericllai@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
|
|
Deku has two Ethernet ports. Currently both get assigned the wrong
MAC address due to the LAN devices indices being swapped and
vpd ethernet_mac0() affects device eth1 and vpd ethernet_mac1() affects
device eth0.
Correct the device indices for LAN devices so ethernet_mac[0-1] in vpd
can apply to the correct ethernet ports.
BUG=b:320203629
BRANCH=firmware-rex-15709.B
TEST=vpd -s ethernet_mac0=<mac address0>
vpd -s ethernet_mac1=<mac address1>
reboot the system and check ifconfig
eth0 and eth1 MAC addresses are fetched correctly
Change-Id: Id1508104cbb5cf0a234f34f9db19cc535fdb634b
Signed-off-by: Tony Huang <tony-huang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81564
Reviewed-by: Eric Lai <ericllai@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Derek Huang <derekhuang@google.com>
|
|
The power_limits_config variable for ADL/RPL is array data, but we got
soc_power_limits_config variable without its index. So correct the
code to get the proper pointer of the data for current CPU SKU.
I tried to override the PL4 value to 80W from 114W with following
table in ramstage.c as a test for bug b/328729536.
```
const struct cpu_power_limits limits[] = {
{PCI_DID_INTEL_RPL_P_ID3, 15, 6000, 15000, 55000, 55000, 80000},
}
```
And then verified the msr_pl4 value on ChromeOS using Intel PTAT tool.
- Before this patch: msr_pl4 was not changed, it's always 114
- After this patch: msr_pl4 was changed to 80
BUG=None
BRANCH=None
TEST=Built and tested the function could adjust PL4 on xol in local.
Change-Id: I9f1ba25c2d673fda48babf773208c2f2d2386c53
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81436
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
Reviewed-by: Eric Lai <ericllai@google.com>
|
|
Update GPIO configuration according to the schematic changes. The
locations of speaker and DMIC are swapped.
- Speaker: I2S2 -> I2S1
- DMIC: GPP_S2/GPP_S3 -> GPP_R4/GPP_R5
BUG=b:318584606
TEST=FW_NAME=xol emerge-brya coreboot chromeos-bootimage
Change-Id: I3468d79f33d9d9ef8377ccf0f8f628956b02d3c3
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81444
Reviewed-by: Eric Lai <ericllai@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Varshit Pandya <pandyavarshit@gmail.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
|
|
ISH Firmware name needs to be configured only when full sensing
capabilities are enabled through ISH_ENABLE FW_CONFIG. Similarly DMA
property needs to be added only when UFS is enabled through STORAGE_UFS
FW_CONFIG. Hence configure the ISH device at run-time based on
FW_CONFIG.
BUG=b:319164720
TEST=Build Brox BIOS image and boot to OS.
Change-Id: I678416acd48e03ab77ae299beae6e295a688b8df
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81418
Reviewed-by: Varshit Pandya <pandyavarshit@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <ericllai@google.com>
|
|
Add Synaptics touchpad via HID-I2C interface in I2C5 bus for glassway.
BUG=b:331677400
BRANCH=firmware-nissa-15217.B
TEST=emerge-brya coreboot and check touchpad function work.
[INFO ] input: PNP0C50:00 06CB:CE9B Touchpad as /devices/pci0000:00/0000:00:19.1/i2c_designware.5/i2c-17/i2c-PNP0C50:00/0018:06CB:CE9B.0001/input/input4
[INFO ] hid-multitouch 0018:06CB:CE9B.0001: input,hidraw0: I2C HID v1.00 Device [PNP0C50:00 06CB:CE9B] on i2c-PNP0C50:00
Change-Id: Ifbb2cb750a80bc6e8f96609257dcd1e695ad1fa4
Signed-off-by: Frank Chu <frank_chu@pegatron.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81552
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Varshit Pandya <pandyavarshit@gmail.com>
|
|
Create the sundance variant of nissa reference board by copying the
template files to a new directory named for the variant.
Due to new_variant.py limitation that repo can no longer be used in
inside, created this CL manually following google suggestion.
BUG=b:328505938
TEST=util/abuild/abuild -p none -t google/brya -x -a
make sure the build includes GOOGLE_SUNDANCE
Change-Id: Ia8ba318f18d2cac69898687311631778e61bf2ea
Signed-off-by: Leo Chou <leo.chou@lcfc.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81347
Reviewed-by: Derek Huang <derekhuang@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Shou-Chieh Hsu <shouchieh@google.com>
|
|
Add a new Kingler follower device 'Kyogre'
BUG=b:318614302
TEST=emerge-corsola coreboot
Change-Id: Iae3857a9f8edadcc2eee3500fda2e76c0334221c
Signed-off-by: Kei Hiroyoshi <hiroyoshi.kei@fujitsu.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81218
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Varshit Pandya <pandyavarshit@gmail.com>
Reviewed-by: Yidi Lin <yidilin@google.com>
|
|
Change-Id: If68303cd59b287c8a5c982063b2ab75fd74898d6
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81477
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Reviewed-by: Jakub Czapiga <czapiga@google.com>
|
|
Currently, simply changing the wake event configuration to ANY does
not completely resolve the issue of inserting a pen not waking the
system. The pen actually needs to wake up the system both when plugged
in and when pulled out. This is because in the pen's GPP_F15
configuration, the original attribute is EDGE_SINGLE, which should be
changed to EDGE_BOTH.
BUG=b:328351027
TEST=insert and remove pen can wakes system up.
Change-Id: I1823afd0bcb86804227117d2d5def38788bc7387
Signed-off-by: Qinghong Zeng <zengqinghong@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81441
Reviewed-by: Weimin Wu <wuweimin@huaqin.corp-partner.google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <ericllai@google.com>
|
|
Create the yavista variant of the nissa reference board by copying
the template files to a new directory named for the variant.
(Auto-Generated by create_coreboot_variant.sh version 4.5.0.)
BUG=b:321583226
BRANCH=None
TEST=util/abuild/abuild -p none -t google/brya -x -a
make sure the build includes GOOGLE_YAVISTA.
Change-Id: I6fa464a4dcd9551a42e8746e64c724b3582dbe02
Signed-off-by: Hsueh Rasheed <hsueh.rasheed@inventec.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80342
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Derek Huang <derekhuang@google.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
Wake signal from EC is routed to GPP_D1 and hence GPE_EC_WAKE
corresponds to GPE0_DW1_01. Fix GPE_EC_WAKE configuration.
BUG=b:329026602
TEST=Build Brox BIOS image and boot to OS. Trigger suspend and wake up
using EC generated events like AC connect/disconnect.
Change-Id: Ifb89bd0de7b7fc316792e801ed5a1d3f25ca5b1c
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81526
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Shelley Chen <shchen@google.com>
Reviewed-by: Kangheui Won <khwon@chromium.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Keith Short <keithshort@chromium.org>
|
|
Change-Id: Ieaaba5b36796d97449896b8475744a21f01e93d1
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81380
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <patrick.rudolph@9elements.com>
|
|
Return statement is not useful in void function.
Change-Id: I8cf020de335e4da933b7bbdc27b7ac6f31afe885
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81430
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Other files in the commits that added these files were licensed under
GPL-2.0-only, and the project as a whole is GPL-2.0-only, so use that
as the license.
Change-Id: I6c1a7ba582f61f98069ebf3857a8b5bdc8588c3e
Signed-off-by: Nicholas Chin <nic.c3.14@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81421
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Assign GPP_C0 and enable only the touchscreen. Before modification,
GPP_C0 supplies power to the touchscreen and sensor at the same time.
Now the hardware circuit has been modified, GPP_C0 supplies power to the
touchscreen alone. After the software is synchronously modified, when
the device enters suspend(S0ix), GPP_C0 will not enable VDD, which can
reduce the standby power consumption of the touchscreen when it is
suspended(S0ix), which is about 2.1mW.
BUG=b:304920262
TEST= touchscreen function workable
Change-Id: Ia06209aa8303be4fc0669c5d6e5d7a06e8e9ab99
Signed-off-by: Qinghong Zeng <zengqinghong@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81265
Reviewed-by: Eric Lai <ericllai@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Weimin Wu <wuweimin@huaqin.corp-partner.google.com>
|
|
Configure I2C0/1 timing in devicetree to meet timing requirement.
(THIGH(us) minimum is 0.6us).
Before:
I2C0 : THIGH(us) 0.595us
I2C1 : THIGH(us) 0.582us
After:
I2C0 : THIGH(us) 0.673us
I2C1 : THIGH(us) 0.666us
Change-Id: I79af4fde4eb08d4eb896794756a633701bebb755
Signed-off-by: Ivy Jian <ivy.jian@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81348
Reviewed-by: Shelley Chen <shchen@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
The previous value of 32MB was set to meet Google's ChromeOS reqs,
but hampers real-world performance in Linux/Windows, so increase it
to 128MB to match the "auto" default for the Picasso UEFI firmware.
TEST=build/boot Windows on google/zork (morphius), verify UMA set
to 128MB.
Change-Id: I8c6487a4cb8155f826d20fd3ceca87859829199c
Signed-off-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81364
Reviewed-by: Martin L Roth <gaumless@gmail.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jason Glenesk <jason.glenesk@amd.corp-partner.google.com>
|
|
This patch creates a new tivviks variant, which is a Twinlake
platform. This variant uses Nivviks board mounted with the
Twinlake SOC and hence the plan is to reuse the existing
nivviks code.
BUG=b:327550938
TEST= Genearte the Tivviks firmware builds and verify with boot check.
Change-Id: Ia833a1dad45e13cd271506ade364b116c5880982
Signed-off-by: Sowmya V <v.sowmya@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81262
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Dinesh Gehlot <digehlot@google.com>
Reviewed-by: Eric Lai <ericllai@google.com>
|
|
Set FW_CONFIG bit 21 to enable ISH PCI device and define ISH main
firmware name so ISH shim loader can load firmware from file system.
ISH also need to be enabled if STORAGE_UFS is set.
BUG=b:280329972
TEST= Set bit CBI FW_CONFIG bit 21
Boot Brox board, check that ISH is enabled and loaded
lspci shows: 00:12.0 Serial controller: Intel Corporation Alder
Lake-P Integrated Sensor Hub (rev 01).
Change-Id: Iadc5108c62737d27642a6948c00b5c122541aaba
Signed-off-by: Li Feng <li1.feng@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80773
Reviewed-by: Tanu Malhotra <tanu.malhotra@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Shelley Chen <shchen@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Yuval Peress <peress@google.com>
|
|
Select USE_UNIFIED_AP_FIRMWARE_FOR_UFS_AND_NON_UFS in brox Kconfig.
This enables a single binary for both SKU1 and SKU2. For SKU2, upon
boot from cold reset, it will disable the UFS Controller and then
trigger a warm boot.
BUG=b:329209576
BRANCH=None
TEST=Boot image on SKU1/SKU2 and check S0ix working.
Change-Id: Iabd0b3a83aa386e09310b671632368807a4018d4
Signed-off-by: Ashish Kumar Mishra <ashish.k.mishra@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81224
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Shelley Chen <shchen@google.com>
|
|
Update eMMC DLL settings based on Craaskov board.
BUG=b:318323026
TEST=executed 2500 cycles of cold boot successfully on all eMMC sku
Change-Id: I56f8329c28261c2bcae9d058da929be6763b293c
Signed-off-by: Ian Feng <ian_feng@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81304
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Simon Yang <simon1.yang@intel.com>
Reviewed-by: Eric Lai <ericllai@google.com>
|
|
Update touchpad and touchscreen I2C timing.
- Data hold time: 300ns - 900ns
BUG=b:328724191
BRANCH=firmware-nissa-15217.B
TEST=Check wave form and met the spec.
I2C1 (touchscreen) Hold time from 83.58ns to 413.87ns
I2C5 (touchpad) Hold time from 95.93ns to 425.27ns
Change-Id: I65fb1298f9e96ab0b63aba436f6a319f21b38925
Signed-off-by: Frank Chu <frank_chu@pegatron.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81136
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Shawn Ku <shawnku@google.com>
|
|
Adjust touchscreen power sequencing for eKTH5015M.
The INX touch panel (eKTH5015M) contains a pull-up register which causes TCHSCR_REPORT_EN pull-up abnormally from Z1 power on.Because the t25 must be at least greater than 20ms, TCHSCR_REPORT_EN is initialized to GPO_L in the early stage (romstage) to meet the spec.
BUG=b:328170008
BRANCH=firmware-nissa-15217.B
TEST=Build and check I2C devices timing meet spec.
[INFO ] input: Elan Touchscreen as /devices/pci0000:00/0000:00:15.1/i2c_designware.1/i2c-10/i2c-ELAN0001:00/input/in4
Change-Id: I50f9c21ddee2bc9c1d313f63049cb587b4ae047a
Signed-off-by: Frank Chu <frank_chu@pegatron.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81135
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Eric Lai <ericllai@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Currently, inserting the pen does not wake the system, only removing
the pen does. This is caused by the wake event configuration being
DEASSERTED, so change it to ANY.
BUG=b:328351027
TEST=insert and remove pen can wakes system up.
Change-Id: Icdea995c2be04ea459e985f79269e49faf88248d
Signed-off-by: Jianeng Ceng <cengjianeng@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81102
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Shou-Chieh Hsu <shouchieh@google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Derek Huang <derekhuang@google.com>
Reviewed-by: Weimin Wu <wuweimin@huaqin.corp-partner.google.com>
|
|
Create the bujia variant of the brask reference board by copying
the template files to a new directory named for the variant.
(Auto-Generated by create_coreboot_variant.sh version 4.5.0).
BUG=b:327549688
BRANCH=None
TEST=util/abuild/abuild -p none -t google/brya -x -a
make sure the build includes GOOGLE_BUJIA
Change-Id: I453a50f1aa64f8d4119bf0f860d928aa3e00a144
Signed-off-by: Shon Wang <shon.wang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81198
Reviewed-by: Eric Lai <ericllai@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kevin Chiu <kevin.chiu.17802@gmail.com>
|
|
This patch enables the `SOC_INTEL_COMMON_BASECODE_RAMTOP` configuration
at the SoC level for all MTL devices. This change streamlines the
configuration process, avoiding redundant selections on individual
mainboards.
BUG=b:306677879
BRANCH=firmware-rex-15709.B
TEST=Verified boot functionality on google/ovis and google/rex.
Change-Id: I3aa3a83c190d0a0e93c267222a9dca0ac7651f9c
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81271
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
This patch ensures Ovis baseboard can select RAMTOP caching to improve
the boot time w/o any runtime hang.
BUG=b:306677879
BRANCH=firmware-rex-15709.B
TEST=Verified boot on google/ovis with ~30ms savings in boot time.
Change-Id: Ic0b73eb8fb9cd6ca70d3d7168b79dfd0fbc550e3
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81270
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
NVMe using clk_src[0] and clk_req[1] mapping to hardware design,
Due to inconsistency between PMC firmware and FSP, we need to set
clk_src to clk_req number, not same as hardware mapping in coreboot.
Then swap correct setting to clk_src=0,clk_req=1 in mFIT.
BUG=b:328318578
TEST=build firmware and veirfy suspend function on NVMe SKU DUT.
Cq-Depend: chrome-internal:7063434
Change-Id: I1777310782a0f4417bd1bb21287bec5852be966e
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81230
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <ericllai@google.com>
|
|
Modeled after the Rex Kconfigs for ISH.
Change-Id: Ic670d550a9aaad64e52489d895b8aac2aee4b5ed
Signed-off-by: Yuval Peress <peress@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81050
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Define SSFC bit 0-1 in coreboot for add 2nd BOE G7500 touchscreen.
BUG=b:329339069
BRANCH=firmware-nissa-15217.B
TEST=Check touchscreen can detect and function work.
[INFO ] input: GTCH7503:00 2A94:A804 as /devices/pci0000:00/0000:00:15.1/i2c_designware.1/i2c-10/i2c-GTCH7503:00/0014
Change-Id: I85688919864e3cac1beb2442ef3e23fe9d5f916c
Signed-off-by: Frank Chu <frank_chu@pegatron.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81217
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <ericllai@google.com>
|
|
Now that EC software sync has been verified to work on Brox, we can
enable it by default.
BUG=b:326152804
BRANCH=None
TEST=Verify that SW sync occurs
Change-Id: I3d356c006fc448125605761f7328d1f1e203a7c4
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81211
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Pull down USI_REPORT_EN(GPP_C6) in romstage to solve
an abnormal peek pull high before BL_EN.
Because power sequence no meet spec, pre #comment36,
it may have ghost touch.
BUG=b:326337003
TEST=FW_NAME=omnigul emerge-brya coreboot, measurement of HW and test
touch detection by evtest
Change-Id: I66f4a7915f135927fbc0a16254dece202dfc23a2
Signed-off-by: Jamie Chen <jamie_chen@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80769
Reviewed-by: Derek Huang <derekhuang@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
|
|
Select USE_UNIFIED_AP_FIRMWARE_FOR_UFS_AND_NON_UFS to use unified AP
FW for UFS/Non-UFS SKUs.
BUG=b:326481458
BRANCH=firmware-brya-14505.B
TEST=FW_NAME=xol emerge-brya coreboot chromeos-bootimage
Change-Id: I85c3c1c7ccaae9d46b66d3e7a2efea6dc9056188
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81107
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
|
|
Create the nova variant of the brask reference board by copying
the template files to a new directory named for the variant.
(Auto-Generated by create_coreboot_variant.sh version 4.5.0.)
BUG=b:328711879
BRANCH=None
TEST=util/abuild/abuild -p none -t google/brya -x -a
make sure the build includes GOOGLE_NOVA
Change-Id: Ie1cee43f0e2545288130bcc5152075603695c395
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81132
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kenneth Chan <kenneth.chan@quanta.corp-partner.google.com>
|
|
Disable unused controllers in overridetree.cb by referring to xol proto2
schematics. Enabling unused controllers blocks entering s0ix.
- I2C3
- SATA
- PCIE RP8
- PCIE RP9
- GSPI1
BUG=b:328318578
BRANCH=firmware-brya-14505.B
TEST=FW_NAME=xol emerge-brya coreboot chromeos-bootimage
Change-Id: I1be7caf8234c32406aa2cff8fc7fe9fa39b16d89
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81105
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Update psys_pmax value to 122 from 145. This value is from internal
power team.
BUG=None
BRANCH=firmware-brya-14505.B
TEST=FW_NAME=xol emerge-brya coreboot chromeos-bootimage
Change-Id: I8bc58343d5736e2457db006972dc229e16d3fe59
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81104
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
Enable Acoustic noise mitigation for xol. The setting values are from
internal power team.
- Enable Acoustic noise mitigation
- Set slow slew rate VCCIA and VCCGT to SLEW_FAST_4
- Set FastPkgCRampDisable VCCIA and VCCGT to 1
BUG=None
TEST=FW_NAME=xol emerge-brya coreboot chromeos-bootimage
Change-Id: I6165ae6ca73d1467a1d2cc7bd545298bd4c2f54f
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81103
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
|
|
For SKU1, wake pin is WLAN_PCIE_WAKE_ODL.
Update gpio config and corresponding ACPI for WoWLAN.
BUG=b:327379404
BRANCH=None
TEST=Boot image on SKU1 and check Wake on WLAN from S0ix.
Change-Id: I04c35da2c9ac57cafdf7f7a35d83ab2e7a05fe4a
Signed-off-by: Ashish Kumar Mishra <ashish.k.mishra@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80780
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Shelley Chen <shchen@google.com>
|
|
Update eMMC DLL values to improve initialization reliability.
BUG=b:327123701
TEST=Improve reboot on MB with eMMC smoothly.
Change-Id: Ice9ee217acf7dc6e3e704bc82529e0b9a8faf184
Signed-off-by: Daniel Peng <Daniel_Peng@pegatron.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80779
Reviewed-by: Shawn Ku <shawnku@google.com>
Reviewed-by: Eric Lai <ericllai@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Simon Yang <simon1.yang@intel.com>
|
|
Currently, the oak boards are the only boards that build the ChromeEC
by default as a part of the coreboot build.
As a part of replacing the chromeec submodule with a different build
mechanism, disable this default.
Signed-off-by: Martin Roth <gaumless@gmail.com>
Change-Id: Idd4fe45e52dbdd1c8dccf0d2c09d5cf6d61aa839
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81023
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Reviewed-by: Yidi Lin <yidilin@google.com>
|
|
Add VGPIO configurations for NVMe on PEG60.
BUG=b:326481458, b:372086400
BRANCH=firmware-brya-14505.B
TEST=Verified DUT could detect NVMe.
Install ChromeOS into NVMe and boot from it.
Change-Id: I5520dc2a4bf6e788701a774674d223b7e8ad5b44
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81033
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
Add FW_CONFIG probe to separate touch panel settings.
TOUCH_PANEL_ENABLE/TOUCH_PANEL_DISABLE
Use different gpio tables based on the value of TOUCH_PANEL.
BUG=b:325987249
TEST=emerge-nissa coreboot and run in DUT
Change-Id: I23c62406a932815ff1cfafe05b70468b1f9cca54
Signed-off-by: Yunlong Jia <yunlong.jia@ecs.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80850
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Kyle Lin <kylelinck@google.com>
|
|
Add wifi sar table for dochi
BUG=b:326137130
BRANCH=firmware-brya-14505.B
TEST=emerge-brya coreboot chromeos-bootimage
Change-Id: Iaf90756eb318bef1ffcda9368a976c0ca209a100
Signed-off-by: Morris Hsu <morris-hsu@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80809
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Bob Moragues <moragues@google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
Turn off SD ASPM L1.1/L1.2 as w/a for wlan DMA resume failure
We completed 4 runs for each of the 2 tests - power_idle and power_VideoCall. Here are the averages for both the tests:
L1ss disabled SD plugged power idle test: 735.3875
L1ss enabled SD plugged power idle test: 737.2335
L1ss disabled SD plugged power video test: 333.29325
L1ss enabled SD plugged power video test: 333.442
BUG=b:254382832
TEST=test pass over 10k cycles
Signed-off-by: Jason Nien <finaljason@gmail.com>
Change-Id: I4d903f0f6333ffa18069e42be3c932aeae8013d9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80237
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-by: Tim Van Patten <timvp@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
BUG=none
TEST=Verify CSE telemetry data in boot time data on Yahiko.
Before:
```
yahiko-rev9 ~ # cbmem -t
71 entries total:
0:1st timestamp 197,583 (0)
```
After:
```
yahiko-rev9 ~ # cbmem -t
76 entries total:
990:CSME ROM started execution 0
944:CSE sent 'Boot Stall Done' to PMC 49,000
945:CSE started to handle ICC configuration 49,000 (0)
946:CSE sent 'Host BIOS Prep Done' to PMC 51,000 (2,000)
947:CSE received 'CPU Reset Done Ack sent' from PMC 168,000 (117,000)
0:1st timestamp 195,861 (27,861)
```
Signed-off-by: Kapil Porwal <kapilporwal@google.com>
Change-Id: I3f90d0462cb766655bf8e59a90bc550ceefb2256
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79768
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
For boot beep functionality, relevant register values are
required to be updated.
BUG=b:324528901
BRANCH=None
TEST=Build & verified Boot Beep functionality on Brox
Change-Id: If236c8ac173a279db676af412377fa4e4122c1cd
Signed-off-by: poornima tom <poornima.tom@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80416
Reviewed-by: Krishna P Bhat D <krishna.p.bhat.d@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change ClkSrc index for NVME to 0 from 1 by referring to proto2
schematics.
BUG=b:326481458
BRANCH=firmware-brya-14505.B
TEST=FW_NAME=xol emerge-brya coreboot chromeos-bootimage
Change-Id: I7ea1cd7d8e16d4cee953e931d2f1829eae7d1978
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80768
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
Add 2 configuration on Kconfig for glassway.
- DRIVERS_GENERIC_GPIO_KEYS
- DRIVERS_GENESYSLOGIC_GL9750
BUG=b:319071869
BRANCH=firmware-nissa-15217.B
TEST=Local build successfully and boot to OOBE normally.
Change-Id: Id7e358d2f472cd435d2828f6256f5ee91dfb8ef6
Signed-off-by: Daniel Peng <Daniel_Peng@pegatron.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80766
Reviewed-by: Shawn Ku <shawnku@google.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Eric Lai <ericllai@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
Refer to the reference board of nivviks, and update GPIO settings
via glassway schematic of ca24a_r10_240108_v3_mb_gsen_gmr.pdf.
BUG=b:319071869
BRANCH=firmware-nissa-15217.B
TEST=Local build successfully and boot to OOBE normally.
Change-Id: I0de743746160c6eb081cb9a061ac1703b01ba5b4
Signed-off-by: Daniel Peng <Daniel_Peng@pegatron.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80764
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Eric Lai <ericllai@google.com>
|
|
Several users complained of link's fan not running at all, particularly
when using ChromeOS Flex. Enabling auto fan control at boot/s3 resume
resolved the issue for them.
Change-Id: I8f0db6b6c94fac2e0dcb580be0f6df839780c38c
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80713
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
No Windows driver exists or is needed, so hide to prevent an unknown
device from being listed in Windows Device Manager. Same change was
made for frostflow variant previously.
TEST=build/boot Win11 on skyrim, verify unknown device for the
fingerprint reader no longer present.
Change-Id: Ia700aa4ccd478bc734db012e1419e566a5dcf493
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80711
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add STORAGE config in FW_CONFIG to support NVME sku.
- STORAGE_UFS : 0
- STORAGE_NVME: 1
BUG=b:326481458
BRANCH=firmware-brya-14505.B
TEST=FW_NAME=xol emerge-brya coreboot chromeos-bootimage
Change-Id: Id8316f643ba9a55319b67431a24a507e92419aa7
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80767
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Eric Lai <ericllai@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
Refer to the reference board of nivviks, and update devicetree settings
via glassway schematic of ca24a_r10_240108_v3_mb_gsen_gmr.pdf.
BUG=b:319071869
BRANCH=firmware-nissa-15217.B
TEST=Local build successfully and boot to OOBE normally.
Change-Id: Ibbb10a373bd5fa52a0833b81133517d2a088536b
Signed-off-by: Daniel Peng <Daniel_Peng@pegatron.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80742
Reviewed-by: Eric Lai <ericllai@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
IOEX was replaced with GPIOs, this CL makes the required changes
BUG=b:325533052
TEST=Built FW image correctly.
Change-Id: I09ebba336b179cb36c6801b47ee0be5ade08c257
Signed-off-by: Eran Mitrani <mitrani@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80570
Reviewed-by: Derek Huang <derekhuang@google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
GPP_F19 and GPP_F20 sre set incorrectly previously. Change them to not
connected according to schematics.
BUG=b:305793886
TEST=Built FW image correctly.
Change-Id: Ifb6da1f8696f44cb47be3d1de83c55e62b12a9e9
Signed-off-by: Eran Mitrani <mitrani@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80569
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Eric Lai <ericllai@google.com>
|
|
Starting from MT8195, MediaTek platform supports "dram adaptive" to
automatically detect dram information, including channel, rank, die
size..., and can automatically configure EMI settings. So we can just
pass a placeholder param blob to `mt_mem_init_run` by enabling this
option.
Platforms (MT8173, MT8183, MT8192) which do not support "dram adaptive"
need to implement `get_sdram_config` to get onboard DRAM configuration
info.
TEST=emerge-geralt coreboot && emerge-asurada coreboot
TEST=CONFIG_MEDIATEK_DRAM_ADAPTIVE is set to y on geralt
TEST=CONFIG_MEDIATEK_DRAM_ADAPTIVE is no set on asurada
Change-Id: I05a01b1ab13fbf19b2a908c48a540a5c2e1ccbdc
Signed-off-by: Yidi Lin <yidilin@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80687
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
Improve SSD readiness time by enabling earlier power sequencing.
Here are the two GPIOs to look for:
* GPP_A19: Power Enable
* GPP_A20: PERST
The flow is presented as `stage (GPIO PAD/Value)` for easy
understanding:
bootblock (A20/0, A19/1)
|
v
romstage (A20/1)
Ideally, we don't need SSD power sequencing at ramstage, hence, remove
the logic from ramstage.
TEST=Able to build and boot google/deku using NVMe without any problems.
S0ix and read/write from/to SSD are also normal.
Change-Id: Iedaff8a793f1ba5d2b97352b95c4dfdd2b818ebd
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80664
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Improve SSD readiness time by enabling earlier power sequencing.
Here are the two GPIOs to look for:
* GPP_A19: Power Enable
* GPP_A20: PERST
The flow is presented as `stage (GPIO PAD/Value)` for easy
understanding:
bootblock (A20/0, A19/1)
|
v
romstage (A20/1)
|
v
ramstage (A19/1, A20/1)
Ideally, we don't need SSD power sequencing at ramstage, but due to the
fact that Karis has RO locked, any change in the bootblock won't be
applicable for FSI'ed karis devices. Therefore, we're keeping the
existing ramstage power sequencing flow as is
TEST=Able to build and boot google/karis using NVMe without any
problems. S0ix and read/write from/to SSD are also normal.
Change-Id: I79171a7830b75f5c20bbe30023f2814a62743a13
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80663
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Tyler Wang <tyler.wang@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Improve SSD readiness time by enabling earlier power sequencing.
Here are the two GPIOs to look for:
* GPP_A19: Power Enable
* GPP_A20: PERST
The flow is presented as `stage (GPIO PAD/Value)` for easy
understanding:
bootblock (A20/0, A19/1)
|
v
romstage (A20/1)
Ideally, we don't need SSD power sequencing at ramstage, hence, remove
the logic from ramstage.
TEST=Able to build and boot google/ovis using NVMe without any problems.
S0ix and read/write from/to SSD are also normal.
Change-Id: I891b5a6d2c29f5d940793a4e90215265f2a4fcd8
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80642
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
|
|
Improve SSD readiness time by enabling earlier power sequencing.
Here are the two GPIOs to look for:
* GPP_A19: Power Enable
* GPP_A20: PERST
The flow is presented as `stage (GPIO PAD/Value)` for easy
understanding:
bootblock (A20/0, A19/1)
|
v
romstage (A20/1)
Ideally, we don't need SSD power sequencing at ramstage, hence, remove
the logic from ramstage.
TEST=Able to build and boot google/rex0 using NVMe without any problems.
S0ix and read/write from/to SSD are also normal.
Change-Id: Idde2f7693771f1d7e3171e51232d1bb899bfe33e
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80641
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
|
|
Improve SSD readiness time by enabling earlier power sequencing.
Here are the two GPIOs to look for:
* GPP_A19: Power Enable
* GPP_A20: PERST
The flow is presented as `stage (GPIO PAD/Value)` for easy
understanding:
bootblock (A20/0, A19/1)
|
v
romstage (A20/1)
|
v
ramstage (A19/1, A20/1)
Ideally, we don't need SSD power sequencing at ramstage, but due to the
fact that Screebo has RO locked, any change in the bootblock won't be
applicable for FSI'ed screebo devices. Therefore, we're keeping the
existing ramstage power sequencing flow as is.
TEST=Able to build and boot google/screebo using NVMe without any
problems. S0ix and read/write from/to SSD are also normal.
Change-Id: I0ee1fa4613178da8771c9e6b5ee871e50ea6324c
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80640
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Early EC Sync does not need to be enabled in coreboot as EFS2 is being
enabled in the EC.
BUG=b:326152804
BRANCH=None
TEST=emerge-brox coreboot
To be tested with EC sync enabled
Change-Id: I08bdbe9f3dcea837b0b148adc137c03d3461877a
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80689
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
BUG=b:320203629
BRANCH=firmware-rex-15709.B
TEST=emerge-ovis coreboot built FW image correctly.
Change-Id: I8db065e25e21406f1966d8020a3b926b3a62ae12
Signed-off-by: Tony Huang <tony-huang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80685
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
|
|
Add supported memory parts in mem_parts_used list, and generate SPD ID
for these parts.
DRAM Part Name ID to assign
K3KL8L80CM-MGCT 0 (0000)
K3KL6L60GM-MGCT 1 (0001)
H58G56AK6BX069 2 (0010)
H9JCNNNBK3MLYR-N6E 3 (0011)
BUG=b:319071869
BRANCH=firmware-nissa-15217.B
TEST=Run command "go run ./util/spd_tools/src/part_id_gen/\
part_id_gen.go ADL lp5 \
src/mainboard/google/brya/variants/glassway/memory/ \
src/mainboard/google/brya/variants/glassway/memory/\
mem_parts_used.txt"
Change-Id: I00ae3efe8e554f44cee5a27ac88c5d65eb95f7fb
Signed-off-by: Daniel Peng <Daniel_Peng@pegatron.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80686
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Daniel Peng <daniel_peng@pegatron.corp-partner.google.com>
|
|
Add support memory parts for Xol.
- Samsung K3KL6L60GM-MGCT
- Samsung K3KL8L80CM-MGCT
BUG=b:319506033
BRANCH=firmware-brya-14505.B
TEST=FW_NAME=xol emerge-brya coreboot chromeos-bootimage
Proto board can boot to ChromeOS.
Change-Id: Ic6a36e40f0f93109f296c5cc67a368ace81bd217
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80637
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
Update memory configuration following proto schematics.
BUG=b:319506033
BRANCH=firmware-brya-14505.B
TEST=FW_NAME=xol emerge-brya coreboot chromeos-bootimage
Proto board can boot to ChromeOS.
Change-Id: I59aabe0870317092f59701bdf88b53bf9731377a
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80326
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Eric Lai <ericllai@google.com>
|
|
Update initial DTT policy and TCC setting for Xol. The setting values
are from internal power team.
- Critical CPU temparature: 105 -> 99
- TCC offset: 90 -> 94
BUG=b:323989520
BRANCH=firmware-brya-14505.B
TEST=FW_NAME=xol emerge-brya coreboot chromeos-bootimage
Change-Id: I546b313a1e6af16029309174a5bed2d1e4aa4d11
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80410
Reviewed-by: Eric Lai <ericllai@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
Set tdp_pl1_override to 15 for performance required by the thermal team.
Fix policies.critical index from 2 to 0.
BUG=b:313833488
TEST=emerge-nissa coreboot
Change-Id: I5341bd3d4842f9298a2f5d9e589918bb1b06ba69
Signed-off-by: Weimin Wu <wuweimin@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80620
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Eric Lai <ericllai@google.com>
|
|
Keeping the PM timer enabled will disqualify an ADL system from entering
S0i3, and will also cause an increase in power during suspend states.
The PM timer is not required for brya boards, therefore disabling it.
Fixes: 0e90580 (soc/intel: transition full control over PM Timer from
FSP to coreboot)
This mirrors an identical commit for google/brya: 1ce0f3aab72d
("mb/google/brya: Fix S0i3 regression")
TEST=Boot Linux on google/drobit, verify S0i3 counter incrementing after
exiting S0ix suspend states.
Change-Id: I644e42388c0f6127512bf52e774b79721601ecc9
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80612
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Create the glassway variant of the nivviks reference board by copying
the template files to a new directory named for the variant.
BUG=b:319071869
BRANCH=firmware-nissa-15217.B
TEST=None
Change-Id: I597666a5be6f71b82c7baddbe343da3d5117dd1c
Signed-off-by: Daniel Peng <Daniel_Peng@pegatron.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80636
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Daniel Peng <daniel_peng@pegatron.corp-partner.google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Eric Lai <ericllai@google.com>
|
|
Enable DPTF functionality for brox board
BRANCH=None
BUG=b:324360936
TEST=Built and tested on brox board
Change-Id: I0315f7f45688ccc36d321d6be4fa4fac7559a16b
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80418
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <ericllai@google.com>
|
