| Age | Commit message (Collapse) | Author |
|---|
|
One specific Hynix LPDDR5x DRAM part requires an ABL workaround to
eliminate DRAM-related failures during a FAFT test, but due to the
use of generic/common SPDs, there is no way for the ABL to determine
the DRAM part # itself.
Consequently, we will have coreboot check the DRAM part #, and set/clear
a CMOS bit as appropriate, which the ABL will check in order to apply
(or not apply) the workaround.
The ABL already uses byte 0xD of the extended CMOS ports 72/73 for
memory context related toggles, so we will use a spare bit there.
BUG=b:270499009, b:281614369, b:286338775
BRANCH=skyrim
TEST=run FAFT bios tests on frostflow, markarth, and whiterun without
any failures.
Change-Id: Ibb6e145f6cdba7270e0a322ef414bf1cb09c5eaa
Signed-off-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75698
Reviewed-by: Martin Roth <martin.roth@amd.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jason Glenesk <jason.glenesk@amd.corp-partner.google.com>
|
|
Instead of adding the new PCI IDs of the XHCI controllers in every new
chip generation to the pci_xhci driver, bind the driver to the internal
PCI devices of the XHCI controllers via the device ops statement in the
chipset devicetree. The PCI device function of the XHCI2 controller in
Mendocino can be either a dummy device or the XHCI controller, so the
device ops are attached to that device in the mainboard devicetree
instead. The Glinda code is right now just a copy of the Mendocino code,
so it'll change in the future, but for consistency the equivalent
changes to those in Mendocino are applied there too.
Since the device ops are now attached to the devices via the static
devicetree entry, also remove both the xhci_pci_driver struct and the
amd_pci_device_ids array from drivers/usb/pci_xhci/pci_xhci.c.
TEST=SSDT entries for the XHCI controllers are still generated on
Mandolin.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I9c455002c6d2aac576fe24eee0c31744b4507bb0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75713
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jon Murphy <jpmurphy@google.com>
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
Add 'common_config.acp_config' to the device tree, so we have the
correct pin configuration.
BUG=b:225320579
TEST=USE=fwconsole emerge-skyrim ... ; verify 'devbeep' works in
depthcharge console
TEST=Boot into ChromeOS, verify YouTube sound works with internal
speakers and headphone jack
TEST=Boot into ChromeOS, verify microphone with Google Meet
Change-Id: Ie2d79408104273d8a53214b683800fa0663c14d3
Signed-off-by: Tim Van Patten <timvp@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74962
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Commit f99d6700 ("mb/google/skyrim/var/winterhold: Fix USB port ACPI
generation") fixed the USB-A ports being double-nested, but neglected
to move the chip driver registers up into the correct scope. While the
generated ACPI is still correct, fix the register scope anyway to
avoid confusion.
BUG=b:283778468
BRANCH=skyrim
TEST=build/boot winterhold, dump ACPI, verify unchanged
Change-Id: Ia9982fed0fe2093d787ee9506ac5bbadd6cc03f9
Signed-off-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75389
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
Commit d81ee3f1 ("mb/google/skyrim/var/markarth: Fix USB port ACPI
generation") fixed the USB-A ports being double-nested, but neglected
to move the chip driver registers up into the correct scope. While the
generated ACPI is still correct, fix the register scope anyway to
avoid confusion.
BUG=b:283778468
BRANCH=skyrim
TEST=build/boot markarth, dump ACPI, verify unchanged
Change-Id: I5c1cd23c49b512f55e9e13b2164d30dfb7fb682d
Signed-off-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75388
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
Commit a539893c ("mb/google/skyrim/var/frostflow: Fix USB port ACPI
generation") fixed the USB-A ports being double-nested, but neglected
to move the chip driver registers up into the correct scope. While the
generated ACPI is still correct, fix the register scope anyway to
avoid confusion.
BUG=b:283778468
BRANCH=skyrim
TEST=build/boot frostflow, dump ACPI, verify unchanged
Change-Id: I3912fe1b7d3f2a07cb379928cd4f5d87100d3284
Signed-off-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75387
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
The overridetree definitions for the USB ports wrongly double-nested
the ports, causing the generated SSDT to be incorrect, leading to
an error in dmesg:
ACPI BIOS error (bug): Could not resolve symbol \
[\_SB.PCI0.GP41.XHC1.RHUB.HS02.HS03], AE_NOT_FOUND
BUG=b:283778468
BRANCH=skyrim
TEST=untested, but same error/fix as frostflow variant.
Change-Id: Ic498afcc8b8e0224f344f405e2f1ef6184df1d6b
Signed-off-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75340
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Jason Glenesk <jason.glenesk@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
|
|
The overridetree definitions for the USB ports wrongly double-nested
the ports, causing the generated SSDT to be incorrect, leading to
an error in dmesg:
ACPI BIOS error (bug): Could not resolve symbol \
[\_SB.PCI0.GP41.XHC1.RHUB.HS02.HS03], AE_NOT_FOUND
BUG=b:283778468
BRANCH=skyrim
TEST=untested, but same error/fix as frostflow variant.
Change-Id: Ie40541ada508acfa5771ea800249b8a57b168e3b
Signed-off-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75339
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jason Glenesk <jason.glenesk@gmail.com>
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
|
|
The overridetree definitions for the USB ports wrongly double-nested
the ports, causing the generated SSDT to be incorrect, leading to
an error in dmesg:
ACPI BIOS error (bug): Could not resolve symbol \
[\_SB.PCI0.GP41.XHC1.RHUB.HS02.HS03], AE_NOT_FOUND
BUG=b:283778468
BRANCH=skyrim
TEST=build/boot frostflow, verify error no longer present in dmesg.
Change-Id: I0b87af6b2c04f9354e6f394a8f987fa660e49134
Signed-off-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75338
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Jason Glenesk <jason.glenesk@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
|
|
According to Thermal table 0518, adjust DPTC and STT settings.
BRANCH=none
BUG=b:273636128
TEST=emerge-skyrim coreboot chromeos-bootimage
Then the thermal team has verified.
Signed-off-by: John Su <john_su@compal.corp-partner.google.com>
Change-Id: Id1c1884eabc1ea58148270f39eaca836ccc3fb54
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75326
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Chao Gui <chaogui@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Ian Feng <ian_feng@compal.corp-partner.google.com>
Reviewed-by: Amanda Hwang <amanda_hwang@compal.corp-partner.google.com>
Reviewed-by: Frank Wu <frank_wu@compal.corp-partner.google.com>
|
|
Set the DmaProperty in the device's _DSD so that the OS can treat the
device as untrusted.
BUG=b:278310256
TEST=cat /sys/bus/pci/devices/<wifi>/untrusted == 1
iperf3 -c <iperf3-server> -t 60 (No performance regressions seen)
Change-Id: I06369a19afa5b881b26f5c1eb243e2db41a9bb36
Signed-off-by: Mark Hasemeyer <markhas@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75095
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Van Patten <timvp@google.com>
|
|
We have largely dropped from filling in mainboard_ops.name
as unnecessary. A common place should be decided where or if
this information is added in the console log.
Change-Id: I917222922560c6273b4be91cd7d99ce2ff8e4231
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74450
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
|
|
Because SPL fuse needs to be set before the FW lock. So enable
Markarth project to send the fuse SPL (security patch level)
command to the PSP.
BUG=b:279499511
BRANCH=none
TEST=FW_NAME="Markarth" emerge-skyrim coreboot chromeos-bootimage
Then get "PSP: SPL Fusing Update Requested." in the firmware log.
Signed-off-by: John Su <john_su@compal.corp-partner.google.com>
Change-Id: I8fbbd89d11b1bdb2c95c761955c10bedb366fd70
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74753
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Update Samsung 4G K3KL6L60GM-MGCT support
BRANCH=None
BUG=b:243337816
TEST=emerge-skyrim coreboot
Change-Id: I89b9798c16635a32dff12f1c0b65737d3c16cd59
Signed-off-by: Rex Chou <rex_chou@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74740
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Set edp_panel_t9_ms to 8ms which means it will delay 8ms
between backlight off and vary backlight off.
BUG=b:271704149
BRANCH=Skyrim
TEST=Build; Verify the UPD was passed to system integrated table;
Signed-off-by: Chris Wang <chris.wang@amd.corp-partner.google.com>
Change-Id: I952d05b18e29cf30256f43562a5052007c5c6268
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74790
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-by: Jason Glenesk <jason.glenesk@gmail.com>
Reviewed-by: Martin Roth <martin.roth@amd.corp-partner.google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Rename the UPD pwr_on_vary_bl_to_blon to edp_panel_t8_ms to
match the eDP sequence timing in milliseconds.
BUG=b:271704149
BRANCH=Skyrim
Test=Build/Boot to ChromeOS
Signed-off-by: Chris Wang <chris.wang@amd.corp-partner.google.com>
Change-Id: Iecdfe47cd9142d8a1ddeee0ec988d37b2a11028e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74787
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-by: Jason Glenesk <jason.glenesk@gmail.com>
Reviewed-by: Martin Roth <martin.roth@amd.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
Because WD SSD drive isn't holding the clock low for some reason.
So we change to read eMMC clkreq signal instead.
BRANCH=none
BUG=b:274377518
TEST=emerge-skyrim coreboot chromeos-bootimage and verify ok.
Change-Id: I1329386631dc54209db54ac146e4aafe95b6a3ac
Signed-off-by: Rex Chou <rex_chou@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74599
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Van Patten <timvp@google.com>
Reviewed-by: Martin Roth <martin.roth@amd.corp-partner.google.com>
|
|
By default, coreboot includes support for all the different types of SPI
ROMs. Excluding the unused ROM types shrinks ramstage by almost 4k.
BUG=b:267735039
TEST=Build & Boot ROM
BRANCH=Skyrim
Signed-off-by: Martin Roth <gaumless@gmail.com>
Change-Id: If6e402269d1f2cac8256d478eb36743441497bdf
Reviewed-on: https://review.coreboot.org/c/coreboot/+/72769
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Van Patten <timvp@google.com>
Reviewed-by: Jon Murphy <jpmurphy@google.com>
|
|
Mendocino and Rembrandt don't have an eMMC controller and also don't
have GPIO pins that eMMC signals can be multiplexed on, so drop the eMMC
related code from Mendocino.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ib8ec49a7084bdd62e480baee75a280fde8b13d01
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74660
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
|
|
Because WD SSD drive isn't holding the clock low for some reason.
So we change to read eMMC clkreq signal instead.
BRANCH=none
BUG=b:278495684
TEST=emerge-skyrim coreboot chromeos-bootimage and verify ok.
Signed-off-by: John Su <john_su@compal.corp-partner.google.com>
Change-Id: I3a9225473a6ae1ba01dc8e5d982c4999f073267e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74583
Reviewed-by: Chao Gui <chaogui@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martin.roth@amd.corp-partner.google.com>
Reviewed-by: Tim Van Patten <timvp@google.com>
Reviewed-by: Frank Wu <frank_wu@compal.corp-partner.google.com>
|
|
On Skyrim variants, the eMMC reset GPIO should be SSD_AUX_RST_L (GPIO6).
Update the port_descriptors to link the correct reset GPIO. Data
is from the skyrim variant schematics and go/skyrim-gpios.
BUG=b:278759559
TEST=reboot: 5 iterations
suspend_stress_test: 10 iterations
Signed-off-by: Jon Murphy <jpmurphy@google.com>
Change-Id: I4713b3af23bb7684c9e2e81cf9c8d8a560b41a79
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74512
Reviewed-by: Tim Van Patten <timvp@google.com>
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martin.roth@amd.corp-partner.google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Update the blob type for TypeId0x25_Mp2Fw_MDN_AD03.sbin to
subprogram 0. Delete the extra MP2FW line.
BUG=b:246770914
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Change-Id: I5418b1ed59e1916b971d2eece9f6a2fd0e51b1b3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74327
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martin.roth@amd.corp-partner.google.com>
|
|
With EC's lid switch implementation, there is no need to maintain the
lid switch state in mainboard. Hence remove LIDS ACPI object from
mainboard.
BUG=None
TEST=Build Skyrim BIOS image and boot to OS. Read the lid switch state
correctly through /proc/acpi/button/lid/LID0/state.
Change-Id: I0f8dc7216337268c421a475f54ee5b28abf33d08
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74333
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
From request, all type C port limit to to Gen1 5GHz.
So enable UPD usb3_port_force_gen1 for Markarth.
BUG=b:273841155
BRANCH=skyrim
TEST=Build, verify the setting will be applied on Markarth.
Signed-off-by: John Su <john_su@compal.corp-partner.google.com>
Change-Id: I9314b67a82ad2993c87f0110db5ec927caaa772b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74087
Reviewed-by: Patrick Huang <patrick.huang@amd.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Chao Gui <chaogui@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Reviewed-by: Amanda Hwang <amanda_hwang@compal.corp-partner.google.com>
Reviewed-by: Ian Feng <ian_feng@compal.corp-partner.google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
Because Markarth PCIe port 1 use for eMMc not SD. So we need override
PCIe config for Markarth. And also the Markarth have NVMe and eMMC
SKU. Follow Winterhold to look at the NVMe CLKREQ signal before
initializing the ports allowing us to identify which device is populated
and only initialize that device.
BRANCH=none
BUG=b:275669215
TEST=emerge-skyrim coreboot chromeos-bootimage
Signed-off-by: John Su <john_su@compal.corp-partner.google.com>
Change-Id: I0b4e4067a30019d742c7589a52badf93b7091615
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74133
Reviewed-by: Martin Roth <martin.roth@amd.corp-partner.google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Frank Wu <frank_wu@compal.corp-partner.google.com>
|
|
On Skyrim, there isn't a need for a sleep GPIO table. Remove the TODO
and filler table and function to reduce unnecessary function overhead.
BUG=None
BRANCH=Skyrim
TEST=Build Skyrim BIOS image.
Change-Id: Ia9d55a5e2295bb2e2c2957c4f5207362f616022c
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73852
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jon Murphy <jpmurphy@google.com>
|
|
Having L1.2 enabled on the SD port increases the kernel resume times by
between 30 & 40ms. This patch disables L1.2 on SD to get that time
back.
As with needing to have hotplug enabled on the SD card, this seems like
a driver issue, so hopefully that will get sorted out and this patch
can be reverted.
BUG=b:274025743
TEST=resume times are decreased.
BRANCH=skyrim
Signed-off-by: Martin Roth <gaumless@gmail.com>
Change-Id: I2c409fa2cd66c712c5ba7104635499d63fa0d2be
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74118
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Use die_no_apcb to cause a build error when the APCB or SPD sources are
not found.
TEST=builds with and without matching APCB and SPD sources
Signed-off-by: Fred Reitberger <reitbergerfred@gmail.com>
Change-Id: I62dce2c71061bfc5c01e0344b7dc115a47669140
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73008
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
This sets the location of the skyrim MP2 firmware within the mainboard's
blobs directory, and adds the Kconfig option to the mainboard directory
so that it can be enabled in a saved .config file.
The skyrim MP2 firmware is skyrim specific, so it should not be placed
in the main PSP AMD_BLOBS directory.
We will also only want to enable the MP2 firmware for chromeos builds as
it's not useful for non-chromeos builds.
BUG=b:259554520
TEST=Build MP2 firmware into image, see that it gets loaded
BRANCH=skyrim
Signed-off-by: Martin Roth <gaumless@gmail.com>
Change-Id: I04be6f2d0b605d4eca37fd927a70310259dc106c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73659
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Robert Zieba <robertzieba@google.com>
Reviewed-by: Jon Murphy <jpmurphy@google.com>
|
|
set pwr_on_varybl_to_blon to 0x1c, which means fw will delay 112ms
between backlight on and vary backlight.
BUG=b:271704149
BRANCH=none
TEST=Build; Verify the UPD was passed to system integrated table;
measure the power on sequence on whiterun
Signed-off-by: Chris.Wang <chris.wang@amd.corp-partner.google.com>
Change-Id: Ib966d2ebd4ef4a8085695901ec5da160f467e32e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73753
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jason Glenesk <jason.glenesk@gmail.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Add UPD usb3_port_force_gen1 for skyrim
The default setting is set to disable
Skyrim -> set default as disable
BUG=b:273841155
BRANCH=skyrim
TEST=Build, verify the setting will be applied on skyrim.
Change-Id: Id53bed82a9fef93b574c3f30830555e02d7f4737
Signed-off-by: Patrick Huang <patrick.huang@amd.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73917
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
It seems like the hotplug enable might be doing more than just enabling
devices to be hot-plugged, so re-enable the feature for the SD card.
Removing it from SD increased resume time and may have caused reboot
issues for SD after resume.
This is a partial revert of CB:73512
BUG=b:273620322
TEST=See resume time go down on Skyrim
BRANCH=Skyrim
Change-Id: I4814d4377d0ba8a1e9b308853b3e02a4a27bd8d5
Signed-off-by: Martin Roth <gaumless@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73868
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Frank Wu <frank_wu@compal.corp-partner.google.com>
Reviewed-by: John Su <john_su@compal.corp-partner.google.com>
Reviewed-by: Jon Murphy <jpmurphy@google.com>
|
|
Enable Frostflow platform to send the fuse SPL (security patch level)
command to the PSP.
BUG=b:274028833
BRANCH=none
TEST=FW_NAME="frostflow" emerge-skyrim coreboot chromeos-bootimage
Then get "PSP: SPL Fusing Update Requested." in the firmware log.
Change-Id: I6437d5324877702f2f8b4c69d4c850543e1b74be
Signed-off-by: Frank Wu <frank_wu@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73884
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
This will be tracked directly in the bug, so a code comment is not
needed.
BUG=263161283
TEST=none
BRANCH=Skyrim
Signed-off-by: Martin Roth <gaumless@gmail.com>
Change-Id: I4d5af35762354c8825d30f813098547a7e009e35
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73828
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
We're not going to move the AMDFW binary around at this point, so get
rid of the TODO.
BUG=None
TEST=None
BRANCH=skyrim
Signed-off-by: Martin Roth <gaumless@gmail.com>
Change-Id: If802c3ee19f4e6a3a74da49bbda55f6a89fa8060
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73827
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
|
|
Because Mendocino doesn't support PCIe Gen4, PSPP on this platform does
not save any power, so leave it disabled.
BUG=273889287
TEST=None
BRANCH=skyrim
Signed-off-by: Martin Roth <gaumless@gmail.com>
Change-Id: I1a1c6692cd0a44469a35582042b92eeec31073fa
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73826
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Follow thermal team's request on b/248086651 comment#32. Update the
thermal table setting for each mode and the conditions of temperature
switching.
BUG=b:248086651,b:241180483
TEST=emerge-skyrim coreboot
Change-Id: Ibcf6c110029d39bdc6bfaf46c234a4073ee69f30
Signed-off-by: EricKY Cheng <ericky_cheng@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73732
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Van Patten <timvp@google.com>
|
|
Add new memory MT62F2G32D4DS-026 WT:B to replace H9JCNNNBK3MLYR-N6E．
Add new memory parts in the mem_parts_used.txt and generate the
SPD ID for the parts. The memory parts being added are:
DRAM Part Name ID to assign
MT62F512M32D2DR-031 WT:B 0 (0000)
MT62F1G32D4DR-031 WT:B 1 (0001)
MT62F1G32D2DS-026 WT:B 2 (0010)
MT62F2G32D4DS-026 WT:B 3 (0011)
K3LKBKB0BM-MGCP 4 (0100)
BUG=b:273177939
BRANCH=None
TEST=emerge-skyrim coreboot
Signed-off-by: Yunlong Jia <yunlong.jia@ecs.corp-partner.google.com>
Change-Id: I545bd8d9f88e7b3055acef4066769e6fcb766cc0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73681
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
If recovery APCB is not passed, amdfwtool will build amdfw*.rom with
AMD_BIOS_APCB_BK entry pointing to the same offset as AMD_BIOS_APCB
entry. This will help to save 40 KiB flash space in each FW slot. On
ChromeOS, this means saving ~120 KiB flash space.
BUG=b:240696002
TEST=Build and boot to OS in Skyrim.
Change-Id: Ib3bbc1eededae20b2cd48f514722a207c46536a0
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73662
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
According to file thermal_table_0310, adjust the STT settings.
BRANCH=none
BUG=b:257149501
TEST=emerge-skyrim coreboot chromeos-bootimage
Then the thermal team has verified.
Change-Id: If4500c85dcea051aca15602f1fb4b5ec80b73e67
Signed-off-by: Frank Wu <frank_wu@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73698
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Tim Van Patten <timvp@google.com>
Reviewed-by: Chao Gui <chaogui@google.com>
|
|
Change stop_delay_ms time(T3) from 180 to 150 to meet specification.
T3 min-value of HID-I2C should be 150ms.
BUG=b:267280863
TEST=emerge-skyrim coreboot chromeos-bootimage.
Change-Id: I7ef7db4edaecece1fa5ab07e30a80e556ed35f8b
Signed-off-by: EricKY Cheng <ericky_cheng@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73665
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Van Patten <timvp@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
Add new ram_id:0011 for Micron MT62F1G32D2DS-023 WT:B.
Add new ram_id:0100 for Micron MT62F2G32D4DS-023 WT:B.
DRAM Part Name ID to assign
K3KL8L80CM-MGCT 0 (0000)
H58G56BK7BX068 0 (0000)
MT62F1G32D2DS-026 WT:B 0 (0000)
K3KL9L90CM-MGCT 1 (0001)
H58G66BK7BX067 1 (0001)
MT62F2G32D4DS-026 WT:B 1 (0001)
MT62F512M32D2DR-031 WT:B 2 (0010)
H58G56BK8BX068 3 (0011)
MT62F1G32D2DS-023 WT:B 3 (0011)
H58G66BK8BX067 4 (0100)
MT62F2G32D4DS-023 WT:B 4 (0100)
BUG=b:271188237
BRANCH=None
TEST=FW_NAME=markarth emerge-skyrim coreboot
Change-Id: I59a6a6dff249cd4fe982a4de824848f1bac0ecba
Signed-off-by: John Su <john_su@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73510
Reviewed-by: Frank Wu <frank_wu@compal.corp-partner.google.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
And rename PSP_HW_IPCFG_FILE to PSP_HW_IPCFG_FILE_SUB0
Change-Id: Ia1ab8482074105de367905be2b4b0418066823d2
Signed-off-by: Zheng Bao <fishbaozi@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73531
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
|
|
For simplicity, OEM devices are given a single codename per build variant. Winterhold was intended to be the lead device and was chosen as the code name for this OEM. Unfortunately, Winterhold was cancelled. We attempted to rename Winterhold to Whiterun to avoid future confusion. Again, unfortunately, since some devices were already built, changing the name requires a manual change to force the firmware to be taken by the DUT. This was not a reasonable path forward, so we're abandoning the naming to Whiterun.
This reverts commit af69de494e2c32140ce5e00a1562c2845345b1bf.
Signed-off-by: Jon Murphy <jpmurphy@google.com>
Change-Id: Idef95f0f4f369b235937e1806ce57c427e441f21
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73583
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Tim Van Patten <timvp@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Implement `smm_mainboard_pci_resource_store_init` to store the
resources for XHCI devices. These stored resources are later used by
the elog code to log XHCI wake events.
Example elog contents:
```
244 | 2022-10-11 15:49:24 | S0ix Enter
245 | 2022-10-11 15:49:29 | S0ix Exit
246 | 2022-10-11 15:49:29 | Wake Source | GPE # | 31
247 | 2022-10-11 15:49:29 | Wake Source | PME - XHCI (USB 2.0 port) | 256
248 | 2022-10-11 15:50:08 | S0ix Enter
249 | 2022-10-11 15:50:16 | S0ix Exit
250 | 2022-10-11 15:50:16 | Wake Source | GPE # | 31
251 | 2022-10-11 15:50:16 | Wake Source | PME - XHCI (USB 2.0 port) | 257
```
BUG=b:186792595
TEST=Ran on skyrim proto, verified that wake events show in elog
Change-Id: I529f541a8932267a8825773ddc582beafb27da63
Signed-off-by: Robert Zieba <robertzieba@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68325
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Winterhold boards populate either NVMe or eMMC, but not both.
This means that there is always one link that is unpopulated. The PCIe
configuration code takes longer to verify that a link is unpopulated
than to just train the link, so this slows down the boot by roughly
80ms vs the case when the device is present. Not training the device
at all lowers boot time by another 20ms, for a total of 100ms saved.
Looking at the NVMe CLKREQ signal before initializing the ports allows
us to identify which device is populated and only initialize that
device.
BUG=b:271569628
TEST=Boot Whiterun and eMMC or NVMe correctly work, boot time is lower.
BRANCH=skyrim
Signed-off-by: Martin Roth <gaumless@gmail.com>
Change-Id: I0b87f5e968cd1c87e62a1c0fbdee1fc0723f655d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73441
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
|
|
These ports are not hot pluggable, so drop the parameter, which
will result it in being set to zero / not enabled.
BUG=none
TEST=build boot skyrim, verify all PCIe devices functional.
BRANCH=skyrim
Change-Id: Iaa55cc765e8f073b31f25771633789ac13e2fffa
Signed-off-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73512
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
Reviewed-by: Jon Murphy <jpmurphy@google.com>
|
|
Enable both L1.1 and L1.2 substates for the WiFi, SD card reader,
and SSD (both NVMe and eMMC). If a given device does not support
a particular substate, then it will not be enabled during PCIe
enumeration by coreboot.
BUG=b:270690572
TEST=build/boot multiple skyrim/whiterun/frostflow SKUs with different
storage configs, verify WiFi/SD card/SSD all functional and have L1
substates enabled insofar as they are supported by the device.
BRANCH=skyrim
Change-Id: Ib84df8b9d97282ae696414e52c4a65cfb0a81194
Signed-off-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73438
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
Reviewed-by: Jon Murphy <jpmurphy@google.com>
|
|
This allows variants to override the skyrim port descriptors.
BUG=None
TEST=Tested with following patches
BRANCH=skyrim
Signed-off-by: Martin Roth <gaumless@gmail.com>
Change-Id: I8cff44f5b39d130a7191a69970cae8a88bb5d475
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73294
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Van Patten <timvp@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
|
|
Enable whiterun/winterhold platforms to send the fuse SPL (security
patch level) command to the PSP.
BUG=b:254568112
TEST=On a platform that supports SPL fusing, a message indicating
that fusing was requested will appear in the coreboot console log,
followed by a puff of smoke when the fuse is set and the message
"OK" again on the debug console. (Kidding about the smoke.)
BRANCH=skyrim
Signed-off-by: Martin Roth <gaumless@gmail.com>
Change-Id: I45578597234ba672c89ac421b4626088faca27d5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/72914
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jon Murphy <jpmurphy@google.com>
|
|
Move the sustained_power_limit_mW setting from the baseboard
to variants. This setting will be needed before STT is enabled,
but once STT is enabled, this setting should be removed.
BUG=b:265267957
BRANCH=none
TEST=Build/Boot to ChromeOS
Signed-off-by: Chris Wang <chris.wang@amd.corp-partner.google.com>
Change-Id: I7b9779600cfa8c7581732e936a714728fd618d20
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73426
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Frank Wu <frank_wu@compal.corp-partner.google.com>
|
|
Skyrim does not have a cardbus socket, so disable it.
Maybe cardbus support shouldn't be enabled by default?
BUG=None
TEST="PC Card (PCMCIA) is supported" no longer shows up
in dmidecode output.
Signed-off-by: Martin Roth <gaumless@gmail.com>
Change-Id: Ic941b075e8b5082b5e61e728a77fd79c0ebba35e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73167
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jason Glenesk <jason.glenesk@amd.corp-partner.google.com>
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Only Frostflow supports the stylus, so remove the gpio-keys ACPI node
from Skyrim.
The Kconfig value DRIVERS_GENERIC_GPIO_KEYS is still enabled for all
Skyrim variants, since coreboot will drop the driver from the BIOS image
if there are no references to it (in the devicetree). If some other
design ends up using the stylus in the future we won't have to bring it
back.
BUG: none
TEST: build_packages --board=skyrim chromeos-bootimage --autosetgov
Change-Id: I9ffe215741b72b678d74405769f35167d8ded4b5
Signed-off-by: Tim Van Patten <timvp@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73299
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
|
|
Add new ram_id:0011 for Hynix H58G56BK8BX068.
Add new ram_id:0100 for Hynix H58G66BK8BX067.
The RAM ID table has been assigned as:
DRAM Part Name ID to assign
K3KL8L80CM-MGCT 0 (0000)
H58G56BK7BX068 0 (0000)
MT62F1G32D2DS-026 WT:B 0 (0000)
K3KL9L90CM-MGCT 1 (0001)
H58G66BK7BX067 1 (0001)
MT62F2G32D4DS-026 WT:B 1 (0001)
MT62F512M32D2DR-031 WT:B 2 (0010)
H58G56BK8BX068 3 (0011)
H58G66BK8BX067 4 (0100)
BUG=b:270629852
BRANCH=None
TEST=FW_NAME=markarth emerge-skyrim coreboot
Change-Id: Ida5c8354af71cd92c056a33e38d1fadfc5704977
Signed-off-by: John Su <john_su@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73252
Reviewed-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Reviewed-by: Ian Feng <ian_feng@compal.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
According to thermal_table_0215, adjust DPTC and STT settings.
BRANCH=none
BUG=b:257149501
TEST=emerge-skyrim coreboot chromeos-bootimage
Then the thermal team has verified.
Signed-off-by: Frank Wu <frank_wu@compal.corp-partner.google.com>
Change-Id: Id7df3f9bfa3f0e1337c502bc7db9e09e12cd956a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73081
Reviewed-by: Tim Van Patten <timvp@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: John Su <john_su@compal.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The SPL parameter for DPTC settings is not available for STT-enabled
platforms. It needs to be removed to avoid confusing STT calculations.
BUG=b:265267957
BRANCH=none
TEST=Run the WebGL aquarium with 5000 fish and verify that
there are no power drop peaks.
Change-Id: I8e6dad7d24883f8aadce83ebac401ecd4137d61a
Signed-off-by: Chris Wang <chris.wang@amd.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73124
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Van Patten <timvp@google.com>
|
|
This is causing some issues, so disable it until those issues can be
resolved.
BUG=b:271437658, b:271199389, b:270077971
TEST=Screen always lights up on boot & after S0i3
Signed-off-by: Martin Roth <gaumless@gmail.com>
Change-Id: Id4aa441e4b4f76168f8243b6abafa1cf1ea08dbd
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73393
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Handle the new host event EC_HOST_EVENT_BODY_DETECT_CHANGE.
Previously, the EC sent the host event EC_HOST_EVENT_MODE_CHANGE when
body detection changed between lap/desk mode. However, that event is a
wake event, which resulted in spurious AP wake events being triggered
when the EC detected lap/desk mode changes while the AP was suspended.
To resolve this, the new host event EC_HOST_EVENT_BODY_DETECT_CHANGE was
added, which will not be a wake event. This CL adds handling for the new
event to acpi/ec.asl to switch DPTC tables when a change is detected.
BRANCH=none
BUG=b:261141172
TEST=bodydetectmode on|off, verify host event is received
Change-Id: Iabeb7891489a209f45504804355f1fa817082976
Signed-off-by: Tim Van Patten <timvp@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73298
Reviewed-by: Caveh Jalali <caveh@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Enable HAS_RECOVERY_MRC_CACHE config and add RECOVERY_MRC_CACHE FMAP
section to cache the MRC training data in recovery mode.
BUG=b:270569389
TEST=Build and boot to OS in Skyrim. Ensure that the Type 0x63 BIOS
directory entry is populated with the appropriate MRC_CACHE FMAP
section.
Change-Id: I3f0f41c20b61c96473e887521f84f3ad240adc2b
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73250
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Tim Van Patten <timvp@google.com>
|
|
Use fw_config to probe fingerprint.
BUG=b:269986245
TEST=emerge-skyrim coreboot chromeos-bootimage. Test result is pass
with 1000 reboot cycles.
Change-Id: I4b4bca42dd78dfd5b8636ff3cb05406d2d0c94f7
Signed-off-by: EricKY Cheng <ericky_cheng@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73262
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Van Patten <timvp@google.com>
|
|
Remove ACPI node for pen eject event to meet project design.
BUG=b:265106657
TEST=emerge-skyrim coreboot chromeos-bootimage
Change-Id: I732de49c6319397d93671c48a6518c7c7e955fdc
Signed-off-by: EricKY Cheng <ericky_cheng@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73154
Reviewed-by: Tim Van Patten <timvp@google.com>
Reviewed-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Reviewed-by: Jon Murphy <jpmurphy@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
Add new memory parts in the mem_parts_used.txt and generate the
SPD ID for the parts. The memory parts being added are:
DRAM Part Name ID to assign
MT62F512M32D2DR-031 WT:B 0 (0000)
MT62F1G32D4DR-031 WT:B 1 (0001)
MT62F1G32D2DS-026 WT:B 2 (0010)
H9JCNNNBK3MLYR-N6E 0 (0000)
K3LKBKB0BM-MGCP 3 (0011)
BUG=b:265190498
BRANCH=None
TEST=emerge-skyrim coreboot
Signed-off-by: Yunlong Jia <yunlong.jia@ecs.corp-partner.google.com>
Change-Id: I860f10552e4e4180e09ab805ca82b108fdc8f21a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73049
Reviewed-by: Jon Murphy <jpmurphy@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Setup FW_Config for our project.
Configure USBHub\PIXA Touchpad\Audio(rt5682s & alc1019).
BRANCH=None
BUG=b:262798445, b:268621319
TEST=emerge-skyrim coreboot
Signed-off-by: Yunlong Jia <yunlong.jia@ecs.corp-partner.google.com>
Change-Id: I2c590ae36d4d089f70e1799189cd414f825e5b8b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73048
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Chao Gui <chaogui@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
This patch makes EC wake up AP from s3/s0ix for OS shutdown/hibernate
when the state of charge drops to low_battery_shutdown_percent.
BUG=b:255465618
TEST=emerge-nissa chromeos-bootimage (EC: https://crrev.com/c/4243898)
Verify system resumes from s0ix and then enter S5 on nivviks with steps:
1. disconnect AC
2. powerd_dbus_suspend --disable_dark_resume=false
3. fakebatt 5
4. fakebatt 4
Change-Id: I63b5246432687e38ddfc5733ac3a115c3456d7e9
Signed-off-by: Ivan Chen <yulunchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73082
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Derek Huang <derekhuang@google.com>
|
|
Based on product spec v1.4, update T3 timing from 180 ms to 150 ms.
BRANCH=none
BUG=b:262734395
TEST=emerge-skyrim coreboot chromeos-bootimage
Then the Elan touchscreen works fine.
Signed-off-by: John Su <john_su@compal.corp-partner.google.com>
Change-Id: I0d8f1e008276fccdfbb8c76cfebaccbe71160b64
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73130
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Frank Wu <frank_wu@compal.corp-partner.google.com>
|
|
Based on product spec v1.4, update T3 timing to 150 ms from 300 ms
BRANCH=none
BUG=b:269041202
TEST=emerge-skyrim coreboot chromeos-bootimage
Then the Elan touchscreen works fine.
Change-Id: Ie5bd4bc2c8be2e43470edd374af0623162067497
Signed-off-by: Frank Wu <frank_wu@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73067
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Chao Gui <chaogui@google.com>
|
|
Create the whiterun variant of the skyrim reference board by
copying the winterhold files to a new directory named for the variant.
BUG=b:265955979
BRANCH=None
TEST=emerge-skyrim coreboot and boot up on Whiterun
Change-Id: I3539f84e79c05936fe006bfe9d08743d6a9a6ba7
Signed-off-by: Isaac Lee <isaaclee@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/72483
Reviewed-by: Martin L Roth <gaumless@gmail.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add a FMAP region to support caching GOP-driver-modified VBIOS tables.
Select SOC_AMD_GFX_CACHE_VBIOS_IN_FMAP if CHROMEOS && RUN_FSP_GOP.
Default USE_SELECTIVE_GOP_INIT to y if CHROMEOS && RUN_FSP_GOP.
BUG=b:255812886
TEST=build/boot skyrim, verify cached VBIOS data differs from VBIOS
in CBFS, cached VBIOS data is used when not booting in recovery
or developer modes.
Change-Id: I5857fa4a15250bf6478bffa96b16200e318492b1
Signed-off-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/70900
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Follow thermal table to modify setting.
"stapm_time_constant_s" = "200" to "275"
BRANCH=none
BUG=b:257149501
TEST=emerge-skyrim coreboot
Signed-off-by: John Su <john_su@compal.corp-partner.google.com>
Change-Id: I7fe05fe1c17258a3323b8d04302212e76a388797
Reviewed-on: https://review.coreboot.org/c/coreboot/+/72934
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Tim Van Patten <timvp@google.com>
Reviewed-by: Frank Wu <frank_wu@compal.corp-partner.google.com>
|
|
2/5
of split changes of https://review.coreboot.org/c/coreboot/+/58552/28
Change-Id: I18f73462a3995038fe93750320dfc053fec969ba
Signed-off-by: Zheng Bao <fishbaozi@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/72457
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
|
|
The keyboard reset is not being used on this board, so disable the
functionality.
BUG=None
TEST=Check register values
Signed-off-by: Martin Roth <gaumless@gmail.com>
Change-Id: I4a9f8f254dfefcb32a77f558f984bcdd6004d34b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/72913
Reviewed-by: Jon Murphy <jpmurphy@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
This reverts commit 8e1bb93fb88bc9cc20aab33a1fe09fb4c0c652a0.
Reason: Enabling L.2 breaks some devices on this bridge. Reverting
until a workaround is found and additional testing is done.
Signed-off-by: Martin Roth <gaumless@gmail.com>
Change-Id: I9f721178244e7764e9b08e419db8a8c05ecc29a7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/72916
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jon Murphy <jpmurphy@google.com>
|
|
GPIO 67 is not currently used on skyrim, so set it as no-connect.
Since it's now free for other purposes, make sure that the
SPI-ROM-SHARING functionality is disabled.
BUG=b:268330591
TEST=Examine registers after change
Signed-off-by: Martin Roth <gaumless@gmail.com>
Change-Id: Id083baf41d25920eca09795453a01aac1d00d0f5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/72908
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jon Murphy <jpmurphy@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
BUG=None
TEST=Verify that DMI type 3 - Chassis Information Type field has changed
from Desktop to Laptop
Signed-off-by: Martin Roth <gaumless@gmail.com>
Change-Id: I76c8970fe3fdc2ea322a07f114ad03a0373e152c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/72907
Reviewed-by: Jon Murphy <jpmurphy@google.com>
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Add configuration to bump up the SPI flash bus speed from 66 MHz to 100
MHz for starting next phase.
BUG=b:267539952
TEST=None
Signed-off-by: John Su <john_su@compal.corp-partner.google.com>
Change-Id: Id46201351780bb5bc05422ff36dad6972285690e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/72870
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Chao Gui <chaogui@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Frank Wu <frank_wu@compal.corp-partner.google.com>
|
|
Since the LIDS field is only used in the ACPI code and not in the C code
of any mainboard using the Mendocino SoC, remove it form the global NVS
and add an ACPI object for this in the DSDT of the mainboards that use
it in their ACPI code.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I1ed0407826f579eb14169246b7b14ba677c20e8d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/72185
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
Add configuration to bump up the SPI flash bus speed from 66 MHz to 100
MHz starting the board version of the current phase.
BUG=b:260127676
TEST=Build and boot to OS in Frostflow with 100 MHz SPI bus speed.
Observe that the boot time improved by 100 ms compared to 66 MHz SPI
flash bus speed.
firmware log:
SPI fast read speed: 100 MHz
At 66 MHz:
Total Time: 1,563,384
At 100 MHz:
Total Time: 1,462,570
Change-Id: I9435f4ad0d3541b040703dc9a453badbd080dc09
Signed-off-by: Frank Wu <frank_wu@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/72694
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
|
|
This enables L1.2 for the SSD port.
link_hotplug is unused on Mendocino, so remove it while I'm here, just
as code cleanup. This has no functional difference.
Enabling L1.2 on other devices currently causes problems. Debug is
ongoing.
BUG=b:265890321
TEST=Build & boot, look at states enabled in lspci. Test device
functionality.
Signed-off-by: Martin Roth <gaumless@gmail.com>
Change-Id: I8940856a127c8a4ba45148cbbf07a08b621beb4d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/72391
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
Adding EC_HOST_EVENT_PANIC to SCI mask allows the EC to interrupt the
Kernel when an EC panic occurs. If system safe mode is also enabled
on the EC, the kernel will have a short period to extract and save info
about the EC panic.
BUG=b:266696987
BRANCH=None
TEST=Observe kernel ec panic handler run when ec panics
Change-Id: I9b50ab3c0bcef192ef89f173852cda222f1533c7
Signed-off-by: Rob Barnes <robbarnes@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/72455
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Tim Van Patten <timvp@google.com>
|
|
Follow thermal team's request on b/248086651 comment#27. Update the
thermal table setting for each mode and the conditions of temperature
switching.
BUG=b:248086651
TEST=emerge-skyrim coreboot
Change-Id: Ida10d9b10c33dea11440879afda07c04c1eccb9f
Signed-off-by: EricKY Cheng <ericky_cheng@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/72006
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Reviewed-by: Tim Van Patten <timvp@google.com>
Reviewed-by: Jon Murphy <jpmurphy@google.com>
|
|
The mp2 PCI device is still present when no mp2 firmware is loaded. When
this device isn't explicitly enabled in the mainboard's devicetree, the
chipset devicetree default of the device being disabled is used. This
results in coreboot's resource allocator not allocating resources to the
device and since the bridge doesn't have enough MMIO space reserved, the
Linux kernel can't assign resources to it. To fix this problem, enable
the mp2 device in the mainboard's devicetree so that it gets its
resources assigned by coreboot. An equivalent change was verified on
Chausie.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I1076ccacc6f51bf195b8280a6df5ad1849771519
Reviewed-on: https://review.coreboot.org/c/coreboot/+/72196
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Update setting for touchpad I2C frequency and hold time to meet touchpad
i2c SPEC.
- Frequency: 380 ~ 400 kHz
- hold time : 0.3 ~ 0.9 us
BUG=b:261159229
TEST=On frostflow, touchpad i2c spec from EE measure
Frequencies: I2C0 (Touchpad): 393.7 kHz
Hold time = 0.604 us
Change-Id: Iecf4960a12aa56ac307fb9022e47c4e94a2551c1
Signed-off-by: Rex Chou <rex_chou@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/72114
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Turn on the dxio_tx_vboost_enable for frostflow in coreboot.
It needs to confirm the PCIe Signal Integrity after enabled.
BUG=b:259007881, b:248221908
BRANCH=none
TEST=emerge-skyrim coreboot chromeos-bootimage
Signed-off-by: Frank Wu <frank_wu@compal.corp-partner.google.com>
Change-Id: Iaac331737c83ac7a4a1261c32151359e126a009e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/71926
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
Turn on the dxio_tx_vboost_enable for markarth in coreboot.
It needs to confirm the PCIe Signal Integrity after enabled.
BUG=b:263534907, b:263216451
BRANCH=none
TEST=emerge-skyrim coreboot chromeos-bootimage
Signed-off-by: Frank Wu <frank_wu@compal.corp-partner.google.com>
Change-Id: I0798c1d9788e1911c2643bf387722b072aa79045
Reviewed-on: https://review.coreboot.org/c/coreboot/+/71931
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Reviewed-by: John Su <john_su@compal.corp-partner.google.com>
Reviewed-by: Chao Gui <chaogui@google.com>
|
|
Skyrim doesn't use the firmware TPM, so remove the binary from the
image.
Note that because this was not used, removing it doesn't change the boot
time.
BUG=None
TEST=Boot
Signed-off-by: Martin Roth <gaumless@gmail.com>
Change-Id: Ia627b128c3346a2556c5306de7506519d1f2d70c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/72002
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
|
|
Winterhold runs with the SPI fast read speed set to 100MHz. This
decreases boot time by roughly 100ms.
BUG=None
TEST=Examine boot times.
Signed-off-by: Martin Roth <gaumless@gmail.com>
Change-Id: I879e17fb0212910c7f90ba0e78ee16bea8b7cffa
Reviewed-on: https://review.coreboot.org/c/coreboot/+/71888
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
|
|
Update USB port Type-A Port A0 setting.
BUG=b:261650602
TEST=emerge-skyrim coreboot. Ensure that USB-A port is enumerated correctly in the output of lusub command.
Change-Id: I9563f7b141c34b613cf896f1ce92178617a62c93
Signed-off-by: EricKY Cheng <ericky_cheng@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/71854
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Van Patten <timvp@google.com>
|
|
Update settings for touchpad I2C frequency and data hold time.
I2C frequency and data hold time need to meet touchpad spec.
- I2C frequency: 380kHz - 400kHz
- Data hold time: 0.3us - 0.9us
BUG=b:262320419
TEST=On winterhold, touchpad i2c measurement from vendor,
Frequencies: 395 kHz, Data hold time: 0.66 us
Change-Id: I40fa6f9e88656d4ec02a4120f75a2a9413b5abaa
Signed-off-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/71853
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
Exposing the GPIOs via an ACPI PowerResource and the _CRS results in the
OS driver and ACPI thinking they own the GPIO. This can cause timing
problems because it's not clear which system should be controlling the
GPIO.
Previously, we flagged as an error any device which set the
'has_power_resource' flag but did not set 'disable_gpio_export_in_crs.'
There's no reason to require explicit disablement however, so drop the
superfluous 'disable' flag, and change the _CRS generation to check if
the GPIOs will be exported via the 'has_power_resource' flag instead.
BUG=b:265055477
TEST=build/boot skyrim, dump SSDT and verify touchscreen GPIOs only
listed under PRx, not under _CRS.
Change-Id: I837ae6c6fe4b8e1c4e10686406cba06bdb7759d2
Signed-off-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/71849
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
|
|
Morthal has been overcome by events.
Signed-off-by: Martin Roth <gaumless@gmail.com>
Change-Id: Ice46f4c7400772dbf51eb9d20b61af277daa8513
Reviewed-on: https://review.coreboot.org/c/coreboot/+/71880
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
Update devicetree based on the schematic_20230105.
BUG=b:263534907, b:263216451
BRANCH=None
TEST=FW_NAME=markarth emerge-skyrim coreboot
Change-Id: I437425ac4a7cdb883dc213f5f6bb5f8a33a5577b
Signed-off-by: John Su <john_su@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/71714
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Reviewed-by: Ian Feng <ian_feng@compal.corp-partner.google.com>
|
|
Update setting for touchpad I2C frequency.
And meet touchpad i2c SPEC (380 ~ 400 kHz).
BUG=b:261159229
TEST=On frostflow, touchpad i2c spec from EE measure
Frequencies: I2C0 (Touchpad): 389 kHz
Change-Id: Ie9efd4e597e2701c98064185e5b39a6e256a5f1c
Signed-off-by: Rex Chou <rex_chou@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/71772
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Frank Wu <frank_wu@compal.corp-partner.google.com>
|
|
Enable DPTC support for markarth.
BUG=b:263216451
TEST=emerge-skyrim coreboot
Change-Id: I18c2c840037f65f4f2ca92054247cece28843e45
Signed-off-by: John Su <john_su@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/71720
Reviewed-by: Tim Van Patten <timvp@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
Because skyrim is loading ramstage from SPI with the DMA engine, the
size of the compressed image is less important to load speed than
decompression time.
Because the LZ4 decompression is so much faster than LZMA, compressing
with LZ4 saves us roughly 30ms in boot time.
For size, we're spending roughly 57KiB:
fallback/ramstage 0x9b00 stage 130864 LZMA (305316 decompressed)
fallback/ramstage 0x9b00 stage 189126 LZ4 (305316 decompressed)
Right now we have 2MiB empty space in Skyrim's RO before this change,
and roughly 550KiB empty space in RW, so there aren't currently any
size worries.
Just for fun, I also tested uncompressed ramstage, and it was still
18ms faster than LZMA, but that makes it roughly 12ms slower than LZ4.
BUG=b:264409477
TEST=Boot skyrim, look at boot speed.
Signed-off-by: Martin Roth <martin.roth@amd.corp-partner.google.com>
Change-Id: Iedde6fc2db9d702c0ff2b0081e7baa254ac6699f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/71675
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
|
|
Add new ram_id:0000 for Micron MT62F1G32D2DS-026 WT:B.
Add new ram_id:0010 for Micron MT62F512M32D2DR-031 WT:B
The RAM ID table has been assigned as:
DRAM Part Name ID to assign
K3KL8L80CM-MGCT 0 (0000)
H58G56BK7BX068 0 (0000)
MT62F1G32D2DS-026 WT:B 0 (0000)
K3KL9L90CM-MGCT 1 (0001)
H58G66BK7BX067 1 (0001)
MT62F2G32D4DS-026 WT:B 1 (0001)
MT62F512M32D2DR-031 WT:B 2 (0010)
BUG=b:263296326, b:263216451
BRANCH=None
TEST=FW_NAME=markarth emerge-skyrim coreboot
Change-Id: I3a0d3edb813ef91bfdc68f7400be64fb679dfc04
Signed-off-by: John Su <john_su@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/71619
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Reviewed-by: Ian Feng <ian_feng@compal.corp-partner.google.com>
|
|
Configure GPIOs based on b/263534907#comment4 from EE.
BUG=b:263534907, b:263216451
BRANCH=None
TEST=FW_NAME=markarth emerge-skyrim coreboot
Signed-off-by: John Su <john_su@compal.corp-partner.google.com>
Change-Id: I5346a4322a6538d69d3482948166cfb5bd182021
Reviewed-on: https://review.coreboot.org/c/coreboot/+/71635
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Turn on the dxio_tx_vboost_enable for winterhold/whiterun in coreboot.
It needs to confirm the PCIe Signal Integrity after enabled.
BUG=b:259622787
BRANCH=none
TEST=confirm the setting has been set correspondingly with checking
the FSP log.
Signed-off-by: Chris.Wang <chris.wang@amd.corp-partner.google.com>
Change-Id: I6aad3d9118180d2ffdfba38abc80b175b6f103bd
Reviewed-on: https://review.coreboot.org/c/coreboot/+/71647
Reviewed-by: Jason Glenesk <jason.glenesk@amd.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
|
|
Add new memory parts in the mem_parts_used.txt and generate the
SPD ID for the parts. The memory parts being added are:
DRAM Part Name ID to assign
K3KL8L80CM-MGCT 0 (0000)
H58G56BK7BX068 0 (0000)
K3KL9L90CM-MGCT 1 (0001)
H58G66BK7BX067 1 (0001)
MT62F2G32D4DS-026 WT:B 1 (0001)
BUG=b:263296326, b:263216451
BRANCH=None
TEST=FW_NAME=markarth emerge-skyrim coreboot
Signed-off-by: John Su <john_su@compal.corp-partner.google.com>
Change-Id: I4f00d444bd59443ecba29c6c155d676bab7a3d82
Reviewed-on: https://review.coreboot.org/c/coreboot/+/71632
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Chao Gui <chaogui@google.com>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
|
|
Create the markarth variant of the skyrim reference board by copying
the template files to a new directory named for the variant.
(Auto-Generated by create_coreboot_variant.sh version 4.5.0.)
BUG=b:262092858
BRANCH=None
TEST=util/abuild/abuild -p none -t google/skyrim -x -a
make sure the build includes GOOGLE_MARKARTH
Change-Id: Ifbace841ca56d8659aaffdc31fb2bc4367d96f82
Signed-off-by: Chao Gui <chaogui@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/71610
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
|
|
winterhold/whiterun has different H/W topology to skyrim that the eMMC device
is on a different GPP:
skyrim: GPP1 -> SD
winterhold : GPP1 -> eMMC
BUG=b:263763288
BRANCH=none
TEST=s0i3 stress over 2500 cycles.
Signed-off-by: Chris.Wang <chris.wang@amd.corp-partner.google.com>
Change-Id: Ie6af4287057c6befa0b787ac28d7898166401b29
Reviewed-on: https://review.coreboot.org/c/coreboot/+/71277
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Reviewed-by: Martin Roth <martin.roth@amd.corp-partner.google.com>
|
