| Age | Commit message (Collapse) | Author |
|---|
|
Regenerate SPD for MT53E1G32D2NP-046 WT:B with correct value of ranks.
BUG=b:190692797
TEST=Build and boot to OS
Signed-off-by: Ivy Jian <ivy_jian@compal.corp-partner.google.com>
Change-Id: Icee095c7114f1d6dd960f2134db3816b367bf987
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55384
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Add EC_HOST_EVENT_HANG_DETECT to S3/S5/S0ix wake mask. This event is
sent when the EC detects the AP didn't fully enter a sleep state.
BUG=b:186571086
TEST=Trigger hang detect while AP is in S0ix, AP wakes from S0ix
Change-Id: I09ccf609fc453c19b4fb1ddaa5a0c86d7a85aad1
Signed-off-by: Rob Barnes <robbarnes@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55365
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
Currently variant_has_fpmcu() is called very early in bootblock, before
eSPI is initialized. When checking CBI for its presence, that causes
an error and nothing else can be read from CBI in bootblock.
Moving it slightly later in bootblock doesn't hurt anything from a
timing standpoint, and allows CBI to be read.
BUG=None
TEST=See CBI get read and the FPMCU field read correctly.
Signed-off-by: Martin Roth <martinroth@chromium.org>
Change-Id: I6de44119e92c8820b266f9f07287706c7d4eb505
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54740
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This will tell the kernel to ignore PCI ASPM when suspending the device
and instead place the device into D3. We don't actually have a pin to
control power to the NVMe so we leave it in D3Hot. I'm not sure if
`PCI_RST#` is working correctly on S0i3 suspend/resume. If it's not
acting as expected we can add the reset GPIO and have the OS do it.
BUG=b:184617186
TEST=Run suspend_stress_test on guybrush for 10 cycles
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I29539ac120a9f1b7c1bfeaca745cfc82acfa461a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54967
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Some of the I2C buses are required to operate at different voltage level
compared to other I2C buses eg. I2C bus to Google Security Chip (GSC)
should be at 1.8V level. By default, all the I2C buses are initialized
to operate at 3.3 V. Add support to configure I2C pad RX select through
devicetree and update the concerned devicetree.
BUG=b:188538373
TEST=Build and boot to OS in Guybrush. Ensure that the communication
with GSC is fine. Build Majolica mainboard.
Change-Id: I595a64736fdac0274abffb68c5e521302275b845
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55149
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Some of the GPIOs are either re-purposed for different use-cases or are
unused in upcoming board phase (board version 2). Update the GPIO
configuration accordingly. Here are the GPIOs that are updated:
GPIO Board Id 1 Board Id 2
=============================================
GPIO31 TP183 EN_SPKR
GPIO69 EN_SPKR SD_AUX_REST_L
GPIO70 SD_AUX_RESET_L Unused TP27
GPIO74 RAM_ID_CHAN_SEL Unused TP49
BUG=b:189327557, b:188542649, b:188542497
TEST=Build Guybrush mainboard. Verify Audio is audible and SD card is
detected fine in Board ID 1.
Change-Id: I31523b3e03d2b59577f33eae548747834cfc98aa
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55148
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
GSC is connected with AP via i2c bus so we need to enable i2c in
psp_verstage.
Signed-off-by: Kangheui Won <khwon@chromium.org>
Change-Id: I5f7b73be67a692ea7de31ae53bd111d0e4b6998c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55136
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
In order to resolve the I2C address conflict with another peripheral in
the upcoming hardware build, left speaker amplifier I2C address is
reconfigured.
BUG=b:188539052
TEST=Build Guybrush mainboard. On Guybrush board ID 1, all the 3
speaker amplifiers are added to the ACPI table.
\_SB.I2C2.D028: Realtek SPK AMP L at I2C: 03:28
\_SB.I2C2.D029: Realtek SPK AMP R at I2C: 03:29
\_SB.I2C2.D02A: Realtek SPK AMP L1 at I2C: 03:2a
At the OS side, the concerned speaker amplifiers are probed and
enumerated.
localhost ~ # i2cdetect -y -r 2
0 1 2 3 4 5 6 7 8 9 a b c d e f
00: -- -- -- -- -- -- -- -- -- -- -- -- --
10: -- -- -- -- -- -- -- -- -- -- UU -- -- -- -- --
20: -- -- -- -- -- -- -- -- UU UU -- -- -- -- -- --
30: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
40: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
50: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
60: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
70: -- -- -- -- -- -- -- --
Change-Id: I69a7e7dd65a459c2e5629ada1dea1f1660dd9990
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55028
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This fixes the following error from the Linux kernel:
ccp 0000:03:00.2: ioremap failed
ccp 0000:03:00.2: initialization failed
ccp: probe of 0000:03:00.2 failed with error -12
BUG=b:186575712,b:189202985
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I5cbc620001d3c21c538b62ab2811b6e07269feb2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54962
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
BUG=b:188793754
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I262c4c3ae90d8d12fdfe71a3620739070a444a55
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54931
Reviewed-by: Matt Papageorge <matthewpapa07@gmail.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
All relevant USB phy settings can now be controlled via devicetree.
The given values are the AMD default ones.
For proper tuning procedure and values contact AMD.
Signed-off-by: Julian Schroeder <julianmarcusschroeder@gmail.com>
Change-Id: Ie8d08bde54f8c0cb8202ba111b9c7a9bd33fa03e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54785
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
Add Goodix touchscreen according to the Programming Guide Rev.0.7
BUG=b:188872893
TEST=build and boot into OS.
check dmesg trying to add GDIX0000:00 device.
Signed-off-by: Ivy Jian <ivy_jian@compal.corp-partner.google.com>
Change-Id: I38c9bbf6e1c1531bf3524552db58c0bf183acbb4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54760
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Enable ASPM, Common Clock and Clock Power Managment. Accomplish this
by adding the options in the platform Kconfig as well as dxio
descriptors.
BUG=b:187743927
TEST=Boot to ChromeOS and see ASPM, CC and Clock PM enabled with lspci
Change-Id: Iefc4b5b489cb8caf59f21dd4333d7af66ba47c32
Signed-off-by: Matt Papageorge <matthewpapa07@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54282
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The time constant values were taken from the zork thermal.asl.
BUG=b:186166365
TEST=Boot guybrush to OS and verify logs look correct
thermal-0294 thermal_trips_update : Found critical threshold [3641]
thermal-0321 thermal_trips_update : No hot threshold
thermal-0200 thermal_get_temperatur: Temperature is 3060 dK
thermal-0219 thermal_get_polling_fr: Polling frequency is 100 dS
thermal-0200 thermal_get_temperatur: Temperature is 3060 dK
thermal LNXTHERM:00: registered as thermal_zone0
ACPI: Thermal Zone [TM00] (33 C)
thermal-0200 thermal_get_temperatur: Temperature is 3070 dK
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: Iaeed75bdaa16b117d0fa7144ede98db1388f74f3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54134
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Select GOOGLE_SMBIOS_MAINBOARD_VERSION allows querying
board revision from the EC.
BUG=b:187904819
TEST=1. emerge-guybrush coreboot chromeos-bootimage
2. flash the image to the device and check board rev
by using command `dmidecode -t 1 | grep Version`
Signed-off-by: Ivy Jian <ivy_jian@compal.corp-partner.google.com>
Change-Id: I48dc83d85cfc49e2e4155e389814fce08693c4bd
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54084
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Peers <epeers@google.com>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Rob Barnes <robbarnes@google.com>
|
|
In order to support wake on WLAN events, configure the wake resource.
BUG=b:186011392
TEST=Build and boot to OS in guybrush. Ensure that WiFi power resource
is added to SSDT.
Device (\_SB.PCI0.GP20.WF00)
{
Name (_UID, 0x38B82CBC) // _UID: Unique ID
Name (_DDN, "WIFI Device") // _DDN: DOS Device Name
Name (_ADR, 0x0000000000000000) // _ADR: Address
}
Scope (\_SB.PCI0.GP20.WF00)
{
Name (_PRW, Package (0x02) // _PRW: Power Resources for Wake
{
0x08,
0x03
})
}
Change-Id: Ic238d9606aea20c058e9b47093693f10b14e6288
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52908
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
The 448KB size of the GBB is larger than is needed, so adjust it down
to the minimum size needed.
BUG=b:186761897
TEST=Build & Boot guybrush
Signed-off-by: Martin Roth <martinroth@chromium.org>
Change-Id: I7a24945cd9ecc8872871f57b09ca71fc40e92473
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52764
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Enable Display Controller Engine Audio endpoint to enable HDMI audio.
BUG=b:186479763
TEST=Build and boot to OS in guybrush.
Change-Id: I5e35440e8e70ee125d37c7ac30c9219ec69c7c6e
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52974
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Everybody wants a stylish stylus. Enable the power system to it.
BUG=b:186267293
TEST=connect multimeter to PP5000_PEN and see it go from 0 to 1. MAGIC!
Signed-off-by: Eric Peers <epeers@google.com>
Change-Id: I11d05c118ec9451d26136c320f3650c489e02c59
Reviewed-on: https://review.coreboot.org/c/coreboot/+/53943
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
The PIC IRQs are required so we can correctly set up the PCI_INT
registers. This only matters when booting in PIC mode. We don't need to
set the IO-APIC registers since the linux kernel will auto-assign those
to reduce conflicts.
BUG=b:184766519
TEST=Boot guybrush with `pci=nomsi,noacpi amd_iommu=off noapic` and
verify xhci and graphics continue to work.
$ cat /proc/interrupts
12: 285064 XT-PIC nvme0q0, nvme0q1, rtw88_pci
13: 100000 XT-PIC xhci-hcd:usb1
14: 4032 XT-PIC amdgpu, xhci-hcd:usb3
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I1d66ccd08a86a64242dbc909c57ff9685828f61f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52915
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Using the push-pull alert was causing leakages when in S0i3. This is
because the EC drives ALERT#, so when the AP enters S0i3, the extra
current leaks into the SoC and ends up turning on the power regulators.
By using in-band ALERT#, the EC no longer drives this pin high, thus
fixing the leak. We could also have used an open drain alert, but the
rise time is less than ideal.
BUG=b:187122344, b:186135022
TEST=Measure S0i3 power on guybrush and validate it's no longer high.
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I6de771aeda8feca062652f0ea9eb57d31cb68562
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52955
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Rob Barnes <robbarnes@google.com>
|
|
Some designs might wish to use an open drain eSPI ALERT#. This change
adds an enum that allows setting the eSPI alert mode.
BUG=b:187122344, b:186135022
TEST=Boot guybrush using all 3 alert modes
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: Ia35fc59a699cf9444b53aad5c9bb71aa27ce9251
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52954
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Pen Detect GPIO is exported through GPIO keys driver to the kernel so
that stylus tools is popped on pen eject event. Hence enable the GPIO
keys driver and configure the devicetree.
BUG=b:186011392
TEST=Build and boot to OS in guybrush. Ensure that PRP0001 device is
added to the ACPI SSDT table. Ensure that the Pen Eject events are
detected.
Event: time 1620159356.243180, type 5 (EV_SW), code 15 (SW_PEN_INSERTED), value 1
Event: time 1620159356.243180, -------------- SYN_REPORT ------------
Event: time 1620159356.735316, type 5 (EV_SW), code 15 (SW_PEN_INSERTED), value 0
Ensure that when the device is suspended, it wake on Pen Eject event and
does not wake on Pen Insert event.
Change-Id: I4d2aa29c0f1839c563b40734527a687a5618ba5c
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52906
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Using PAD_WAKE is actually wrong. The wake bits are only supposed to be
set when using the GPIO controller to wake the system. coreboot's
current architecture relies on using GPEs to wake the system.
BUG=b:186011392
TEST=Wake system from S0i3 with EC and see GPE 3 increment.
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: If7f9d2c13503c01fb9d834c436dac723f2c3b24c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52801
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Guybrush is pretty definitely alive, so this can be removed, as the
TODO line said.
BUG=180721202
TEST=Build
Signed-off-by: Martin Roth <martinroth@chromium.org>
Change-Id: I14f89f3e6f780c2da2136a838950ef2bcebc4c3a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52740
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
Update the telemetry setting for guybrush
vddcrvddfull_scale_current : 92165 #mA
ddcrvddoffset : 412
vddcrsocfull_scale_current : 30233 #mA
vddcrsocoffset : 457
BUG=b:182754399
TEST=Build, boot to guybrush
Change-Id: Ib92bb169693634665fc8e165837e7ae3e6137bcf
Signed-off-by: Chris Wang <chris.wang@amd.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52736
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
guybrush and mancomb don't configure any GPIO as PAD_SMI. Since
mainboard_smi_gpi will only get called for a GEVENT that will cause a
non-SCI SMI, this isn't expected to be called. For the unexpected and
very unlikely case that it still does get called, put a printk into
mainboard_smi_gpi to see what is happening there.
TEST=none
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ifd6e3348ecc078932bf6cf5b0830b4b034d274bb
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52360
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Configure Audio Co-processor(ACP) to operate in I2S TDM mode. Also fix
the scope in which ACP is defined in the devicetree.
BUG=b:182960979
TEST=Build and boot to OS in Guybrush. Ensure that the ACPD device is
enabled in the appropriate scope in SSDT.
Change-Id: Ic90fd82e5c34a9feb9a80c4538a45e7c2fb91add
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52645
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
All guybrush boards should have system_configuration set to 2, so
put this in the main devicetree.
BUG=b:185209734
TEST=Build & Boot guybrush
Signed-off-by: Martin Roth <martinroth@chromium.org>
Change-Id: I1ce2acb3b4ed51aa9a0aa379ed125f0b04f04d31
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52680
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: chris wang <Chris.Wang@amd.com>
|
|
This change fixes two problems:
1) We had the enum values for .direction and .level swapped. The naming
is very confusing...
2) ESPI_SYS is not a good event to use for EC SCI. It is a level/low
event that is only cleared by reading the eSPI status register 0x9C.
Cezanne has added a new event source that directly exposes the SCI bit.
This is the correct event source to use for EC SCI.
BUG=b:186045622, b:181139095
TEST=`lpc sci` on EC console and see /proc/interrupts increase by 1
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I764b9ec202376d5124331a320767cbf79371dc07
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52673
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
This enables STAPM power management. Values follow the AMD
specification.
BUG=b:185209734
TEST=Build & Boot guybrush
Signed-off-by: Martin Roth <martinroth@chromium.org>
Change-Id: Ib9f2ec9a8ac118c55ae53b9419ea4ff74ce7b599
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52650
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: chris wang <Chris.Wang@amd.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
BUG=b:185939089
TEST=Build and boot to OS in Guybrush. Enter S0i3 after passing the
sleep state configuration from the mainboard.
Change-Id: I4b23b014ca45bd09c76b626b73b0332586dec056
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52619
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Mathew King <mathewk@chromium.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
The next guybrush build uses 2 new LPDDR4X memory chips:
- Micro MT53E1G32D2NP-046 WT:B
- Hynix H9HCNNNBKMMLXR-NEE
The MT53E2G32D4NQ-046 WT:A chip has been added to the global LPDDR4X
list since the last time guybrush was updated, so that's brought into
the guybrush SPD directory as lp4x-spd-10.hex, but it's not used.
BUG=b:186027256
TEST=Build only
Signed-off-by: Martin Roth <martinroth@chromium.org>
Change-Id: Ia5efd548f8b9442fb3703518387175aba8933a33
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52587
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
Change eSPI bus frequency to 33Mhz.
BUG=b:184356693, b:185514521
TEST=Boot guybrush, observe no eSPI bus errors
Change-Id: Ie2c1b256531f5c7354600e35e9e5191567197feb
Signed-off-by: Rob Barnes <robbarnes@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52402
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add PSP_DISABLE_POSTCODES and PSP_POSTCODES_ON_ESPI kconfig options for
cezanne. Select PSP_DISABLE_DISABLE_POSTCODES and unselect
PSP_POSTCODES_ON_ESPI for guybrush. Port80 codes from PSP can cause bus
errors on guybrush.
BUG=b:185514903, b:184356693
TEST=Boot guybrush, observe no port80 codes from PSP
Change-Id: I7241e47ec1b89782e699135370c796eb251afcaa
Signed-off-by: Rob Barnes <robbarnes@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52401
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This reverts commit 1e36dc078e4012f884d67a32f1faac5f80406285. With EFS2
already enabled in EC, enabling early EC sync is not required. Also a
workaround has been added in payload to address any boot issues.
BUG=b:185277224
TEST=Build and boot to OS in Guybrush in both normal and recovery mode.
Cq-Depend: chromium:2832032
Change-Id: I921dc5c814e5187dce283eeff43075b59885723a
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52418
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
EN_SPKR is routed to SD pin in the ALC1019 speaker amplifier. The
concerned pin has a voltage rating of 1.8V whereas the EN_SPKR GPIO has
a voltage rating of 3.3 V. The schematics has been updated to bridge the
gap. So enable the speaker amplifier by default and add a gpio override
table to disable the speakers before board version 2.
Also update the codec ACPI HID name for the kernel machine driver to
probe the codec successfully.
BUG=b:182960979
TEST=Build and boot to OS in guybrush. Ensure that the GPIO output state
is high.
Change-Id: I32b29bfae9bc94b5119b33a535d8bc825ef89445
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52355
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Mathew King <mathewk@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Enable AMD I2S machine driver and configure the devicetree with HID
information so that the machine driver ACPI objects can be passed to the
kernel.
BUG=b:182960979
TEST=Build and boot to OS in guybrush. Ensure that the ACPI objects for
machine driver is populated.
Change-Id: I8ed474d25273082d1e0742ba93746d97930deb19
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52394
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Enable CRFP in devicetree and configure GPIOs.
BUG=b:182201937
BRANCH=None
TEST=Boot into OS and confirm FPMCU is responding.
Signed-off-by: Ivy Jian <ivy_jian@compal.corp-partner.google.com>
Change-Id: I7c56b0db193be6804d07c2f333445c2a1dbf9f59
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52181
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Add ACPI code to enable the backlight when we enter the OS.
BUG=b:184198808
TEST=Backlight enabled in the OS
Signed-off-by: Martin Roth <martinroth@chromium.org>
Change-Id: I3e0a6c06120ac5abf0a0d82494e03d9cf80c1f8c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52113
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add uart controller to chipset.cb and leave it off by default.
Turn uart0 on for console for mainboards.
BUG=none
TEST=builds and boot into OS
Signed-off-by: Ivy Jian <ivy_jian@compal.corp-partner.google.com>
Change-Id: Iaeb7fea4b92bd89331c7ae7c1c000f8d9961fe9e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52287
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
|
|
BUG=b:185397933
TEST=boot guybrush and no longer see tis_plat_irq_status warnings
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I9b67cb59221d4e355df8e8a2205e03ead7dba51f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52352
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
This is the same as zork.
BUG=b:184126844
TEST=Boot guybrush in developer mode and switch to normal mode.
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: Ib11c255ab7e937de334ecd18dc030006f7724275
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52354
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
BUG=none
TEST=none
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I658372d082a8276f15c7165fe4104de4613fe7d0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52353
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
This include provides the GPIO_x definitions.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I12a0d95f79658f3852132876e92c389b715f3001
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52358
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The board's ec.h file defined EC_SCI_GPI as GEVENT_24, so use that
definition in all places in the mainboard code instead of a mix of the
board specific define and the SoC's GEVENT number define.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I46525ed24e9993acd3d850959dd63761a690d5df
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52309
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
When GPIO_2 was configured as PAD_NF with the WAKE_L function selected
the GPIO_2 override in soc_gpio_hook called soc_route_sci that wrote the
corresponding SCI mapping register, but didn't set up the SCI level and
trigger type, so that couldn't have worked on most of the boards. The
only boards where I think this was actually tested are the google/zork
ones and they configured GPIO_2 as PAD_SCI where the GPIO mux setting is
GPIO mode instead of the WAKE_L mode, but at least the SCI was
configured correctly. The new PAD_NF_SCI macro can configure both the
right GPIO mux setting and set up the SCI configuration correctly, so
use this new macro for the GPIO_2 pin. For test purposes I also added
the corresponding GPIO_2 configuration to amd/mandolin to see if the
affected registers end up having the expected value using the HDT
debugger to look at the registers, but didn't test the wake-up
functionality, since S3 resume isn't working on amd/mandolin yet.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Suggested-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Change-Id: Ic069e46b759fb6746645faccd254263c49a892d4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51756
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
PS/2 keyboard used IRQ 1.
BUG=none
TEST=Boot guybrush and see internal keyboard working
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I97b7382eac28aae2cc82f430c58cf8066b9701e1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52143
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Guybrush doesn't have a PS/2 mouse.
BUG=none
TEST=boot guybrush to the OS
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I87e51d23b69cfd6ad7bb88b364714d679e92728f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52145
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
To train PCIe devices, the devices need to be enabled and taken out of
reset. This patch does the bare minimum needed to train PCIe. It is
not intended to handle timings, which will be addressed later.
Copy the enables for WWAN & WLAN into early GPIO Init so that they're
enabled before FSP-M runs and trains the PCIe busses.
Again, this patch is the minimum to let the FSP train the PCIe busses.
BUG=b:182202136
TEST=Boot guybrush from NVME.
Signed-off-by: Martin Roth <martinroth@chromium.org>
Change-Id: I3807e02de1e9ae40b0a4162217afd6aabb5b04ed
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52115
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This is a temporary workaround for a bug that breaks graphics due to
some power management issue.
Signed-off-by: Matt Papageorge <matthewpapa07@gmail.com>
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ie4c8ff8e827901112fd8b2e993898006bc133241
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52141
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
pcie_rst isn't working correctly, so use the AUX resets to reset the
PCIe devices before training.
BUG=b:182202136
TEST=See PCIe devices train & enumerate
Change-Id: I6db21c79dcbd40c7a8c3f01c60b02882a3851278
Signed-off-by: Martin Roth <martinroth@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52114
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Signed-off-by: Matt Papageorge <matthewpapa07@gmail.com>
Change-Id: Ic8a4349315f8759c79dc6b087b2a933c307cd573
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51957
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
This patch adds the functionality to write the DXIO and DDI descriptors
to the UPD data structure to the SoC code and adds the
mainboard_get_dxio_ddi_descriptors function to each mainboard using the
Cezanne SoC that gets called to get the descriptors from the board code.
Change-Id: I1cb36addcf0202cd56ce99e610a13d6d230bc981
Signed-off-by: Matt Papageorge <matthewpapa07@gmail.com>
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51948
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
This reverts commit 52e61945588bc327844acc4658426861d63ad189.
Reason for revert: Graphics actually works now. I should have abandoned this CL.
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I83aac3a2c616bb434706f23e36549760bc764080
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51985
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
This is locking up the OS. For now this will unblock booting.
BUG=b:183971103
TEST=Boot guybrush to OS
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: Id2b96eedf38c9038169407418c6d36f13299fb62
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51928
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mathew King <mathewk@chromium.org>
|
|
Enable I2C2 in devicetree and fill ACPI information for Codec and
Speaker amplifiers. Pass correct IRQ GPIO for headset jack.
BUG=None
BRANCH=None
TEST=Ensure that the Codec and Speaker Amplifiers are detected in
i2cdetect.
Change-Id: I1ae52a8bbaa0181c906cd14a94de22e0250ed4c1
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52046
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Configure the BT disable GPIO to logic low in order to enable Bluetooth.
Add USB ACPI configuration for BT device.
BUG=b:182201890
TEST=Build and boot to OS.
Change-Id: I647c301e2db6d4a7c5c8cb31cbc47a44cba5e734
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51963
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Configure camera power GPIO to high
BUG=b:182207799
TEST=Build and boot to OS then checked camera device existence with lsusb
Signed-off-by: Ivy Jian <ivy_jian@compal.corp-partner.google.com>
Change-Id: Ie894167e3c4f8efdb3710599c6ff3a9fc975adb6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52017
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Bhanu Prakash Maiya <bhanumaiya@google.com>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Initialize all eSPI signals including PCIE_RST0_L early for EC
communication.
- Set PCIE_RST0_L to a GPIO and set it high to release the bus. This is
a temporary workaround until PCIE_RST_L comes up on its own.
- Make sure all GPIO muxes initialized early are re-initialized.
BUG=b:183340503
TEST=Boot Guybrush
Change-Id: I512cb8b435dc8412cd46189e741ad94e5a24699e
Signed-off-by: Martin Roth <martinroth@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51675
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
BUG=None
TEST=Build and boot to OS in Guybrush. Ensure that the EC Software Sync
is complete.
Change-Id: Id8655b6f805e14ce3cb71777c1cc175f45841fcc
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52009
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
Enable Touchpad by configuring the enable GPIO to logic high. Add
touchpad configuration for ELAN touchpad.
BUG=b:182207444
TEST=Build and boot to OS in Guybrush. Ensure that the trackpad events
are detected using evtest.
Change-Id: Ib47fbb33f2b181eb85f6ded98a5b0ce08fbc7b64
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51962
Reviewed-by: Mathew King <mathewk@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
BUG=b:183737011
TEST=cat /proc/interrupts and see i2c controllers and gpio controller
listed
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I5b2f23b2c2a7c4cec198276814d80f545e85aa41
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51959
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mathew King <mathewk@chromium.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Needed so get_lid_switch will actually call the EC. Otherwise it
returns -1.
BUG=b:183524609
TEST=Depthcharge no longer halts complaining that coreboot didn't sample
the pin
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I4639b3713d726192e251dcffa14381dd92518fa2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51954
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mathew King <mathewk@chromium.org>
|
|
It looks like we are having SI issues on eSPI at 33 MHz. Switching to 16
MHz makes everything a lot more stable.
BUG=b:183524609
TEST=Boot to OS and run `ectool version` 1000 times and see no problems.
Before with 33 MHz there was an error every few cycles.
declare -i i=0; while ectool version; do i+=1; echo "$i"; sleep .11; done; echo "Finished: $i"
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I6ab515629703a157c1d1ac6adcf5cf379e80f8ee
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51953
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Mathew King <mathewk@chromium.org>
Reviewed-by: Rob Barnes <robbarnes@google.com>
|
|
Now that we have the DISABLE_KEYBOARD_RESET_PIN Kconfig option, select
it and remove the temporary workaround that was implemented in the
mainboard code in commit 39ef89033624a2d14b0c77cdbdf287dd7d7059e1.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I634d11290dad8c93f10979f06243b1bf84737ae2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51785
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Guybrush uses GPIO67 as an input.
BUG=none
TEST=Boot guybrush
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I10068bb6870b2cb96033cf3893cde71db5c1d709
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51781
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This change allows guybrush EC communication while other patches
in the SOC code are worked on.
BUG=b:183149183
TEST=Boot guybrush with EC comunication
Signed-off-by: Mathew King <mathewk@chromium.org>
Change-Id: I56fb64d4c065cf0665025346218cc66d77dacb52
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51665
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
GPIO129 is muxed with KBRST, so setting GPIO129 to low causes reset
when KBRSTEN is set to 1. Since reset value of KBRSTEN is 1 we need a
logic to clear it.
BUG=b:183340503
TEST=build
Signed-off-by: Kangheui Won <khwon@chromium.org>
Change-Id: I194e8432a14d6105f6bcf12111647f5aad4e2de2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51727
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
Configure H1 I2C and Interrupt GPIOs during the early initialization.
Add devicetree configuration for H1 device and enable the required
config items.
BUG=b:180528902
TEST=Build Guybrush mainboard.
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Change-Id: I040a5e6101bab0c7425d7b6cc6fbed3b479a5a44
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51544
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Add I2C peripheral reset configuration required during early init.
Enabled I2C generic and HID drivers. I2C GPIOs are configured as
required in CB:50091.
BUG=b:180531661
TEST=Build guybrush mainboard.
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Change-Id: I67690fbd25639879a730260aaca4cddb5e47bbc7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51543
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
GPIOs should be configured in ramstage even if they are configured in an
earlier stage.
BUG=b:180721208
TEST=builds
Signed-off-by: Mathew King <mathewk@chromium.org>
Change-Id: I9896db41dbe2812856357510bc4420482e73ab3d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51547
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
BUG=b:180721208
TEST=builds
Signed-off-by: Mathew King <mathewk@chromium.org>
Change-Id: I8aa54acf1fa9295b27c33a0066432665e6e3755c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51540
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
|
|
BUG=b:181972598
TEST=builds
Signed-off-by: Mathew King <mathewk@chromium.org>
Change-Id: I1abb070324254e21b03bfe00d6eee3b70120564c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51473
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Guybrush does not have a dedicated SCI pin so it uses VW.
BUG=b:181134664
TEST=builds
Signed-off-by: Mathew King <mathewk@chromium.org>
Change-Id: I12fb7c23718ad2350478b89b321e9f0aa099e53b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51238
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
BUG=b:181690884
TEST=builds
Signed-off-by: Mathew King <mathewk@chromium.org>
Change-Id: I8ceeb8db24be34588b370c13d865753f095e4be6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51472
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
This enables the standard library method of adding SPDs to CBFS.
BUG=b:178715165
TEST=Build
Signed-off-by: Martin Roth <martin@coreboot.org>
Change-Id: I2ec94fd866409e1dfa5cb65f6960ea07cbe22f2a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51022
Reviewed-by: Mathew King <mathewk@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add the option to build guybrush firmware with support for EM100.
This will assist in bringup of the new board.
BUG=b:180723776
TEST=builds
Signed-off-by: Mathew King <mathewk@chromium.org>
Change-Id: I2246d2952f341cd8fff8fd486cf989cdb7929411
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51071
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Since not all mainboards based on the Cezanne SoC have to support ACPI
resume, select this option in the mainboard's Kconfig and not in the
SoC's Kconfig.
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I988276ccb5b61837d7f3f015d1d1aba783324b02
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51305
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This adds the Guybrush APCBs into the AMD firmware binary.
BUG=b:182510885
TEST=Build
Signed-off-by: Martin Roth <martinroth@chromium.org>
Change-Id: Iba40cab1d68e9f8d7291e7d715be185a3b6249f3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51418
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mathew King <mathewk@chromium.org>
|
|
BUG=b:180507937
TEST=builds
Signed-off-by: Mathew King <mathewk@chromium.org>
Change-Id: Icb8aba87390475cad7a2a9911c3832a59c987b65
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51240
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
BUG=b:181961514, b:180721208
TEST=builds
Signed-off-by: Mathew King <mathewk@chromium.org>
Change-Id: I0d22de977f09cbf46b28243d9f0c1e9a36e1398f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51295
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Justin Frodsham <justin.frodsham@amd.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Configure early GPIOs in verstage if it is run in PSP otherwise
configure them in bootblock.
BUG=b:181961514, b:180721208
TEST=builds
Signed-off-by: Mathew King <mathewk@chromium.org>
Change-Id: Ib9410089592776ffe198901f2de914fd04bdbade
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51348
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
BUG=b:181961514
TEST=builds
Signed-off-by: Mathew King <mathewk@chromium.org>
Change-Id: I289a2ad1adc5dcc33c5863d6138f66b9b6dc6590
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51294
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
BUG=b:180529005
TEST=builds
Signed-off-by: Mathew King <mathewk@chromium.org>
Change-Id: I94d97a38d992f46b32c2c6aca4c8da688d3b76fc
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51257
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
BUG=b:181910592
TEST=builds
Signed-off-by: Mathew King <mathewk@chromium.org>
Change-Id: I7851d3b11ea3b026b999019d02df1144f8393753
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51270
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
|
|
BUG=b:180653357
TEST=builds
Signed-off-by: Mathew King <mathewk@chromium.org>
Change-Id: Ifd43d9cc1832d8ed8d90c68ba88b5667e3c04f89
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51269
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
BUG=b:180507937
TEST=builds
Signed-off-by: Mathew King <mathewk@chromium.org>
Change-Id: I7b8b2ab73d66e0aaa0e9b7570661c885f7f777ca
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51296
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
BUG=b:180507707
TEST=builds
Signed-off-by: Mathew King <mathewk@chromium.org>
Change-Id: I25ce0ca869ca854ff33242d2c416319e9688cc6f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51264
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
BUG=b:180507937
TEST=builds
Signed-off-by: Mathew King <mathewk@chromium.org>
Change-Id: I3cdd6422b1bc53ea934346327359cbc6d86baeeb
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51043
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
BUG=b:181809122
TEST=builds
Signed-off-by: Mathew King <mathewk@chromium.org>
Change-Id: I64475a475e9b72a6edd04ce0728591e0649d9f60
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51244
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
These files were automatically generated by the lpddr4 version of
gen_part_id.go.
BUG=b:178715165
TEST=Build
Signed-off-by: Martin Roth <martin@coreboot.org>
Change-Id: I3797ba6d52248961418000614a4f7885182521a3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51021
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
These SPDs were generated by the lpddr4 version of gen_spd.go from the
global_lp4x_mem_parts.json.txt file.
BUG=b:178715165
TEST=None
Signed-off-by: Martin Roth <martin@coreboot.org>
Change-Id: I7b9bd04534d6e45dbfe10a0028052978ef3d7c17
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51020
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
BUG=b:180523962
TEST=builds
Signed-off-by: Mathew King <mathewk@chromium.org>
Change-Id: Ic8f30f6d7c4781d4e8451546b39395a74393608f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50882
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
BUG=b:180507937
TEST=builds
Signed-off-by: Mathew King <mathewk@chromium.org>
Change-Id: Ic607d6bca5c70255332a6fbee2b63e6daba7d1e7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51047
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Enabling the GPIO_SIGN_OF_LIFE option will allow for early boot testing.
BUG=b:180721202
TEST=builds
Change-Id: I069623ae76a4e4d1e43a47dd95fdfcece398ebfb
Signed-off-by: Mathew King <mathewk@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51069
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
|
|
BUG=b:180530492
TEST=builds
Signed-off-by: Mathew King <mathewk@chromium.org>
Change-Id: I468d76d0e061431bc819ec12978203614bfe72b4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50919
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Rob Barnes <robbarnes@google.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Enable the building of guybrush variants and configure the first variant
also called guybrush.
BUG=b:180419462
TEST=builds
Signed-off-by: Mathew King <mathewk@chromium.org>
Change-Id: I3bed620378f9152277b4943ead1017f61a21ea82
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50845
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
BUG=b:180419454
TEST=builds
Signed-off-by: Mathew King <mathewk@chromium.org>
Change-Id: I1e724e78b5ef378d474063417aa2b7e57a00886f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50814
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
|
|
BUG=b:175143925
TEST=builds
Signed-off-by: Mathew King <mathewk@chromium.org>
Change-Id: I8d038126b3e511bd16df2144652992c2d5b56c87
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50507
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
